BMW E36 Thermostat Removal And Coolant Flush

Size: px
Start display at page:

Download "BMW E36 Thermostat Removal And Coolant Flush"

Transcription

1 BMW E36 Thermostat Removal And Coolant Flush Disclaimer: The cooling system is critical to the proper operation of your car. Failure to properly install all of the components of the cooling system could result in a damaged engine or you being stranded. Caution must be taken to properly secure your car when working underneath it to avoid injury (or death). Safety notice: When working with engine coolant, precautions must be taken. Coolant is a dangerous chemical to both people and animals. Animals are known to like the taste of coolant due to it's sweet smell. All efforts must be taken to ensure that coolant does end up in any location which may be consumed by animals and should always be disposed of properly. Never remove the radiator coolant cap while the engine is hot. Severe burns can result from hot coolant spraying out of the radiator cap or from the drain plugs. This job was being done on a '98 328iA Cabrio. The reason for doing this work stemmed from the fact that the car was not fully warming up in the winter time. I suspected a faulty thermostat that was not closing properly and decided to replace it. At the same time I chose to replace the stock plastic thermostat housing with an aluminium one based on reports I had read of premature failure of the plastic part. Since the coolant had to be drained (partially) to replace the thermostat, I further decided to flush the entire cooling system and replace all of the coolant with new. Parts needed: A) 2 jugs of BMW coolant B) 2-4 litre jugs of distilled water C) New thermostat (with new o-ring) D) Funnel E) New aluminium thermostat housing (with gaskets) Not shown:

2 * New washer for engine drain plug * 32mm wrench * various size sockets and wrenches * torque wrench (should support 2-25 Nm range) * 1-2 large buckets (that will fit under your car) * floor jack * jack stands * wheel chocks * gloves * rags Section 1 - Coolant Draining and Thermostat Removal Step 1: Perform this work with the engine cold or at least let it cool down for several hours. Step 2: Since the coolant that is put into your car is diluted 50/50 with water, it is easier to pre-mix it before you start pouring it in. To easily do this, get one or two empty 4 litre water jugs and using a measuring cup, measure out the 2 litre and 4 litre marks and put these lines on the side of the jugs. Step 3: Pour 2 litres of distilled water into each of the containers. Do not use tap water as this can cause problems inside your engine. For the couple of bucks it will cost you to get distilled water (from your grocery store), why would you not put the correct stuff in your engine? Step 4: Fill the remainder of each jug with 2 litres of BMW coolant. In most cases this should give you enough coolant mix to refill your car but if you end up needing more you can refill one of the jugs again later. Step 5: Block both rear wheels securely. Step 6: Jack up the front of the car and put both sides on jack stands. Step 7: Inside the car, turn the ignition to the ON position (without starting the car) then turn the heater setting to the highest temperature.

3 Step 8: Turn the ignition off. Step 9: Slide under the front of the car and place a bucket nearby. Unscrew the radiator drain plug and position the bucket to contain the coolant which comes out. If done correctly, no coolant should spill onto the ground. Step 10: After the radiator had fully drained, set the radiator drain plug aside then move the bucket further towards the centre of the car near the oil pan to catch the output from the engine block coolant drain plug. Step 11: The engine drain plug is very difficult to see and can only be accessed from underneath the car. It is located on the passenger side of the engine in between the exhaust headers. On the ' that I did this work on, the drain plug was located right next to one of the oxygen sensors. Feel around with your hand for the only item on that side of the engine that looks like a drain bolt (similar to the oil drain plug). Step 12: On this car, the engine coolant drain plug required a 19mm wrench. Because it was right next to one of the oxygen sensors, it was difficult to remove and took some time to get the wrench in the right spot to loosen the bolt. As soon as the plug is loosened, coolant will start to drip down so have the bucket ready. Note: Do not remove the engine drain plug all the way out. If you keep the drain plug partially in the drain hole, the coolant will come out in a more controller manner. This will allow you to catch all (or most) of it in your bucket as opposed to it falling all over the floor. As needed, use rags to contain any coolant which may be dripping onto the ground. Step 13: Let the remainder of the coolant drain from the rear drain plug. This will probably take up to 30 minutes to complete with the plug still partially in. Step 14: Remove the alternator cooling duct. This duct is not secured with any fasteners so it just removes by pushing it out. Step 15: Remove the 6 screws that attach the shroud.

4 Step 16: Loosen the hose clamps on the two hoses attached to the thermostat housing then slide the hoses off. Bend the hoses out of the way. Step 17: Using the 32mm wrench, loosen the engine fan retaining nut. As the retaining nut is threaded in reverse, you must move the wrench clockwise (to the right) to loosen the nut.

5 Note: If the nut doesn't loosen, try striking the end of the wrench with a rubber mallet. If it still doesn't budge, you may have to try and get a screwdriver in between the pulley bolts to hold it in place. Step 18: Once the fan retaining nut is loose, unscrew it by hand while holding onto the fan (so it doesn't drop when the nut is unscrewed). Step 19: Carefully lift the fan out of the car (being careful not to damage any of the plastic blades or the radiator on the way out). Step 20: Once out of the car, clean the front of the fan of any dirt using a brush. Put the fan aside but store it in an upright position (the same as it normally is in your car). Step 21: Remove the two bolts which secure the engine lift bracket then remove the bracket.

6 Step 22: Remove the remaining 3 bolts to the thermostat housing then lift out the housing. Step 23: Once the thermostat housing is removed, the thermostat will be visible. There will be a small arrow stamped on the thermostat. Observe the orientation of the arrow on the thermostat as the new one will be installed in the same way. Step 24: Remove the thermostat.

7 Step 25: Clean the area around where the thermostat was mounted. Section 2 - Flushing the Engine While the engine coolant has been removed, there still may be sediment in the cooling system which can be more thoroughly removed by "flushing" the system. While the thermostat is removed, it is an ideal time to flush the cooling system as it can be done without having to warm up the car to full operating temperature. Step 1: Reinstall the drain plugs on the radiator and engine block hand tight. Step 2: Install the new thermostat housing without the thermostat (or the original one if you are not installing a new one). Tighten the bolts hand tight. Step 3: Attach the two hoses to the thermostat housing without either hose clamp attached. Step 4: Place some rags around the mouth of the radiator overflow tank. This will hopefully prevent coolant from splashing onto your paint and staining it. Step 5: Using a garden hose or large watering can, fill the radiator with as much water as it will hold. Step 6: Start the engine. Step 7: Monitor the level of water in the radiator and add as needed until no more water can be added. Step 8: Run the car for about 5 minutes. Note: During the flushing process, occasionally check the coolant temperature from inside the car. Turn the engine off if the temperature rises beyond the normal limit. Step 9: Let the car cool down for about minutes then drain the water out of the radiator and engine block as in section 1. Caution: the rear engine drain plug is close to the exhaust pipes which can remain hot for quite a long time after the engine is turned off. If necessary, use a glove to remove the rear drain plug to avoid getting burned.

8 Step 10: Remove the hoses from the thermostat housing then remove the thermostat housing from the engine again. Step 11: There may be some residual gasket material on the thermostat housing or the engine block where the housing mounts to the engine. Using a plastic scraper or other non-metal tool, ensure that both surfaces are clean and all traces of foreign matter are removed. If these surfaces do not mate properly, you may end up with a coolant leak later on. Step 12: Put a new metal washer on the rear drain plug then tighten. While this plug is supposed to be torqued to 25Nm, I found it impossible to get a torque wrench in there and had to tighten it by hand with a wrench. Step 13: Reinstall the radiator drain plug and torque to 2-3 Nm. As this drain plug is made of plastic, it is very easy to strip when installing if not using a torque wrench. Step 14: Install the new thermostat and the new O-ring supplied with it. Ensure that you orient the new thermostat the same way as the one that you removed and that it is facing the right direction front to back. Step 15: Install the gaskets onto the thermostat housing and place the housing over top of the thermostat on the engine. Using the three smaller bolts, hand tighten to hold it in place. Note: When placing the thermostat housing up to the engine, it is important that all gaskets and the thermostat do not fall out of place before the bolts get tightened. If this happens you will have coolant leaks. Step 16: Put the engine lift bracket back in place then tighten the bolts by hand. Step 17: Tighten the bolts to the engine lift bracket to 22Nm. Step 18: Tighten the remaining three thermostat housing bolts to 10Nm. Step 19: Reinstall the lower hose to the thermostat housing and tighten clamp. Ensure that the hose is all the way onto the hose fitting and it not kinked in any way.

9 Step 20: Carefully move the fan back into place and thread the mounting bolt onto the pulley. The manual says to torque to 40Nm without a special BMW tool or 30Nm with the tool. I hand tightened this with the 32mm wrench to what I felt was appropriate. Step 21: Reinstall the upper hose to the thermostat housing and tighten clamp. Step 22: Reinstall the alternator cooling duct then reinstall the 5 mounting screws for the shroud. Step 23: Remove the jack stands and lower the car back to its normal position. Section 3 - Refilling the Engine Coolant Step 1: Using a funnel, start slowly pouring the coolant mix into the overflow tank. Note: Take your time when pouring coolant back into your car. The car will only accept new coolant at a certain rate and will easily overflow. Do everything you can to avoid spilling coolant. Step 2: Fill the new coolant up to the "Cold" mark on the passenger side of the overflow tank. You will find that if you wait a few moments when it gets to this mark the fluid level will go down. Keep adding more fluid until it stops going down and stays at the Cold mark. Note: Having a light source to illuminate the inside of the funnel helps to see where the fluid level. Step 3: Loosen the radiator bleed screw. Step 4: Turn the ignition to the On position but do not start the car. Step 5: Continue to slowly add coolant - adding more after the level has dropped. Step 6: Eventually coolant will start to bubble out of the bleed screw. When the bubbling has stopped and only fluid comes out of the bleed screw hole, tighten the bleed screw while continuing to pour. Step 7: Replace the radiator cap. Step 8: Start the car and let it heat to the normal operating temperature.

10 Step 9: Check for any obvious coolant leaks. Step 10: Using a hose, quickly spray the inside of the engine and underneath the car to rinse away any coolant remnants. Step 11: Clean up your tools. Step 12: Dispose of the old coolant according to the laws in your area. Do not pour coolant down the drain or into the ground. Follow Up: When the car has cooled down for several hours or the next day, check the coolant level in the expansion tank. If it is below the Cold level, add more coolant mix to bring it to this level. For the next day or so, look underneath your car and also inside the engine compartment when it has been parked for several hours to see if there are any leaks. Sometimes a coolant leak may take several days to be noticeable. bimmerdiy.com dan alınmıştır.

How to Install a Mishimoto Radiator for a Mustang 5.0L

How to Install a Mishimoto Radiator for a Mustang 5.0L How to Install a Mishimoto Radiator for a 1979-1993 Mustang 5.0L The below installation instructions work for the following products: Mishimoto Performance Aluminum Radiator - Manual (79-93 5.0L) Here

More information

JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30)

JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30) P. 1 of 12 JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30) Item: Qty: Description: 1 2 1 x 1 x 5/8 Tee Fitting 2 2 Plastic Snap-in Hose Grommet 3 4 1-1/2" Hose Clamps

More information

SAAB 99 Series H Type Engine. Installation Guide Silicone Cooling System Hoses. Classic Silicone Hoses

SAAB 99 Series H Type Engine. Installation Guide Silicone Cooling System Hoses. Classic Silicone Hoses SAAB 99 Series 1981 1984 H Type Engine Installation Guide Silicone Cooling System Hoses Classic Silicone Hoses http://www.classicsiliconehoses.com/ Disclaimer This document is for reference purposes only.

More information

Heater with Air Conditioning. E-Series Ford Aeromaster

Heater with Air Conditioning. E-Series Ford Aeromaster Service Guide Heater with Air Conditioning E-Series Ford Aeromaster Contents Blower Motor...2 Plenum Removal...3 Control Module...6 Servo Motors...8 Coolant Valve and Servo Motor...8 Evaporator Recirculation

More information

Chapter 3 Cooling, heating and ventilation systems

Chapter 3 Cooling, heating and ventilation systems 3 1 Chapter 3 Cooling, heating and ventilation systems Contents Antifreeze mixture..............................see Chapter 1 Cooling fan assembly - testing, removal and refitting.............8 Cooling

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publication No. HEATER KIT P/N 0SE01-HL3-102 (SXS700M2/M4) P/N 0SE01-HL3-103 (SXS700M2D/M4D) SXS700M2/M2D/M4/M4D MII 14607-15172 Issue Date REVISED: June

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publication No. INSTALLATION INSTRUCTIONS HEATER KIT P/N 0SE01-HL3-101 SXS700M4/M2 Honda Dealer: Please give a copy of these instructions to your customer. PARTS LIST REPAIR KIT (P/N

More information

6. Cooling System XCITING 400i. This chapter covers the location and servicing of the cooling system components for the KYMCO XCITING 400i.

6. Cooling System XCITING 400i. This chapter covers the location and servicing of the cooling system components for the KYMCO XCITING 400i. 6. Cooling System XCITING 400i Cooling System This chapter covers the location and servicing of the cooling system components for the KYMCO XCITING 400i. Coolant... 6-3~6-11 Radiator... 6-12~6-23 Thermostat...

More information

51AKB / 51 AKC OWNER S MANUAL

51AKB / 51 AKC OWNER S MANUAL 51AKB / 51 AKC OWNER S MANUAL This manual applies to the following models 51AKB 009 51AKB 012 51AKC 009 51AKC 012 Read this instruction manual thoroughly before using the air conditioner. Control panel

More information

Removal. CAUTION: Do not let tensioner arm snap back to the freearm position, sever damage may occur to the tensioner.

Removal. CAUTION: Do not let tensioner arm snap back to the freearm position, sever damage may occur to the tensioner. Removal 3.7L/4.7L ENGINE CAUTION: Do not let tensioner arm snap back to the freearm position, sever damage may occur to the tensioner. 1. Disconnect negative battery cable from battery. 2. Rotate belt

More information

SECTION 1D ENGINE COOLING

SECTION 1D ENGINE COOLING SECTION 1D ENGINE COOLING CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical

More information

COOLING SYSTEM 1. Section V CONTENTS DATA AND SPECIFICATIONS. Page. Fluid Fan Drive (Silent Flite) 3. Water Pump 4. Radiator 5

COOLING SYSTEM 1. Section V CONTENTS DATA AND SPECIFICATIONS. Page. Fluid Fan Drive (Silent Flite) 3. Water Pump 4. Radiator 5 Section V COOLING SYSTEM CONTENTS Fluid Fan Drive (Silent Flite) 3 Water Pump 4 Radiator 5 Water Temperature Gauge 6 Thermostat 7 Radiator Pressure Cap 7 Service Diagnosis 7 DATA AND SPECIFICATIONS COOLING

More information

6. COOLING SYSTEM 6-0 COOLING SYSTEM MXU 500

6. COOLING SYSTEM 6-0 COOLING SYSTEM MXU 500 6 COOLING SYSTEM SYSTEM FLOW PATTERN----------------------------------------------- 6-1 SERVICE INFORMATION------------------------------------------------ 6-2 TROUBLESHOOTING-----------------------------------------------------

More information

Installation Instructions

Installation Instructions Suzuki Samurai Coolant and Water Hose Kit (SKU# SER-CHK) Installation Instructions SER-HHCK SER-WPI SER-ROP CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools

More information

Heater for BRP Commander. Caution: Before using this product, read this manual and follow all safety instructions. Owner s Manual

Heater for BRP Commander. Caution: Before using this product, read this manual and follow all safety instructions. Owner s Manual Owner s Manual Model: Can Am Commander Heater for BRP Commander Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions Kit Contents Tool Requirement

More information

Chapter 3 Cooling, heating and air conditioning systems

Chapter 3 Cooling, heating and air conditioning systems 3 1 Chapter 3 Cooling, heating and air conditioning systems Contents Air conditioner receiver-drier - removal and refitting............ 16 Air conditioning blower motor (E28/ old-shape 5-series models)

More information

SuperKlean Washdown Products

SuperKlean Washdown Products February 2012 DURAMIX 8000 INSTALLATION AND MAINTENANCE INSTRUCTIONS **DO NOT THROW AWAY AFTER INSTALLATION** **SAVE AND DISPLAY PROMINENTLY WHERE THIS EQUIPMENT IS USED** WARNING HIGH PRESSURE AND HOT

More information

Thermo-Bob 4 Installation Manual KT5A Kit

Thermo-Bob 4 Installation Manual KT5A Kit Thermo-Bob 4 Installation Manual KT5A Kit 2009-2016 KTM 400/450/500 EXC, XC-W 2008-2011 KTM 530 EXC-R 2011 Husaberg FS510 2013-2014 Husaberg FE501 2014-2016 Husqvarna FE501 IM TB4-KT5A V1 Watt-man.com

More information

I had to remove front splash shield to drain the radiator.

I had to remove front splash shield to drain the radiator. At the start of 2013, my cooling was losing significant coolant that seemed to be coming from the water pump. The car had about 107,000 miles on it at the time. I had to remove front splash shield to drain

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK P/N 08T44-SNA-100 2007 MDX BII 32728 Issue Date OCT 2006 PARTS LIST Engine block heater Aluminum washer Heater harness Protective

More information

BASIC SYSTEM LOCATION INDEX

BASIC SYSTEM LOCATION INDEX BASIC SYSTEM LOCATION INDEX 2005 HVAC Basic System - MX-5 Miata Fig. 1: Identifying HVAC Basic System Components BLOWER UNIT REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the

More information

Safety. Rinse Kit for Multi-Pro 1200 and 1250 Turf Sprayers Model No Safety and Instructional Decals. Installation Instructions

Safety. Rinse Kit for Multi-Pro 1200 and 1250 Turf Sprayers Model No Safety and Instructional Decals. Installation Instructions Rinse Kit for Multi-Pro 1200 and 1250 Turf Sprayers Model No. 106-4842 Form No. 3353-529 Rev B Installation Instructions Note: Determine the left and right sides of the machine from the normal operating

More information

Parts & Material Included

Parts & Material Included O² Hydro Well System Installation, Use & Care Guide Parts & Material Included 1. Funnel 11. Drain Line 21. Air Head 2. Media Tank Distributer Tube 12. Air Release 22. Drain Fitting 3. Air Tank Distributer

More information

COOLING SYSTEM. Page CO-2 TROUBLESHOOTING... CO-4 CHECK AND REPLACEMEANT OF ENGINE COOLANT... WATER PUMP... DESCRIPTION...

COOLING SYSTEM. Page CO-2 TROUBLESHOOTING... CO-4 CHECK AND REPLACEMEANT OF ENGINE COOLANT... WATER PUMP... DESCRIPTION... COOLING SYSTEM DESCRIPTION... Page CO-2 TROUBLESHOOTING... CO-4 CHECK AND REPLACEMEANT OF ENGINE COOLANT... WATER PUMP... CO-5 CO-6 THERMOSTAT... CO-8 RADIATOR... CO-9 CO-2 COOLING SYSTEM - Description

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 41826 ENGINE BLOCK P/N 08T44-SNA-101 2010 ODYSSEY Issue Date JUNE 2009 PARTS LIST Engine block heater Aluminum washer NOTE Always use

More information

Mishimoto Performance Aluminum Mustang Radiator - Automatic - (97-04 GT/Cobra/MACH1/Bullitt) - Installation Instructions

Mishimoto Performance Aluminum Mustang Radiator - Automatic - (97-04 GT/Cobra/MACH1/Bullitt) - Installation Instructions Mishimoto Performance Aluminum Mustang Radiator - Automatic - (97-04 GT/Cobra/MACH1/Bullitt) - Installation Instructions The below installation instructions work for the following products: Mishimoto Performance

More information

Radiator Coolant Flush

Radiator Coolant Flush Radiator Coolant Flush Should be done every couple years. Fairly easy job, need a Phillips head screwdriver, 10mm deep socket, couple gallons of water, a gallon of silicate free anti-freeze, needle nose

More information

Heating and ventilation system,

Heating and ventilation system, Page 1 of 24 87-151 Heating and ventilation system, servicing Instrument panel air outlets and air guide ducts CAUTION! Before working on the electrical system: Obtain security code for anti-theft radio.

More information

Dyna-Star HP or HF Pump 35# Pail Kit and Follower Plate

Dyna-Star HP or HF Pump 35# Pail Kit and Follower Plate Instructions Dyna-Star HP or HF Pump 35# Pail Kit and Follower Plate 332517B EN For adapting a 60# Dyna-Star Pump for use with a 35# bucket. For professional use only. Part No.: Important Safety Instructions

More information

Heat Exchanger Block Replacement Instructions

Heat Exchanger Block Replacement Instructions Series 1-4 Gas-fired water boiler Heat Exchanger Block Replacement Instructions Ultra-80 S1-4 Heat Exchanger Block Replacement Kit, Part No. 383-500-773 Ultra-105 S1-4 Heat Exchanger Block Replacement

More information

02 COOLING SYSTEM 02 COOLING SYSTEM COOLING SYSTEM INDEX. 1. General Specifications... 65

02 COOLING SYSTEM 02 COOLING SYSTEM COOLING SYSTEM INDEX. 1. General Specifications... 65 REV. 02 / 01.11.13 COOLING SYSTEM INDE 1. General... 64 2. Specifications... 65 3. Structure and Operation... 65 3.1. Cooling System... 65 3.2. Radiator... 65 3.3. Water Pump... 65 3.4. Thermostat... 65

More information

HFG 12 and 24 Hydrogen Generators Installation Instructions

HFG 12 and 24 Hydrogen Generators Installation Instructions HFG 12 and 24 Hydrogen Generators Installation Instructions Model 12 Model 24 PLEASE READ THESE INSTRUCTIONS FROM BEGINNING TO END BEFORE STARTING YOUR INSTALLATION. If you are still having problems after

More information

Engine Block Heater Service Kits (Tank Type) 30RZ/33RZ/45RZ (CSG 649 Ford Powered) Standby Generator Sets

Engine Block Heater Service Kits (Tank Type) 30RZ/33RZ/45RZ (CSG 649 Ford Powered) Standby Generator Sets TT 880 INSTRUCTIONS 7/92 Engine Block Heater Service Kits (Tank Type) 30RZ/33RZ/45RZ (CSG 649 Ford Powered) Standby Generator Sets Model Voltage Kit No. All Models 120 276380 All Models 240 276381 This

More information

Water Distillation System Instruction Manual Nutriteam TC-501

Water Distillation System Instruction Manual Nutriteam TC-501 Water Distillation System Instruction Manual Nutriteam TC-501 Thank you for purchasing the Nutriteam TC-501 Water Distillation System. It will provide your household with freshly made, ultra clean, great

More information

WS1 Greensand Installation & Start Up Guide

WS1 Greensand Installation & Start Up Guide WS1 Greensand Installation & Start Up Guide Thank you for purchasing a WS1 Water System for the removal of iron, manganese and hydrogen sulphide gas. With proper installation and a little routine maintenance

More information

HT650 TM FAN DRIVE SERVICE INSTRUCTIONS

HT650 TM FAN DRIVE SERVICE INSTRUCTIONS HT650 TM FAN DRIVE SERVICE INSTRUCTIONS When unpacking your product, remove all components and inspect them to ensure that no damage occurred during shipping. If any components are missing or damaged,

More information

Installation Instructions. For the 18 Built-In Dishwasher and Front Color Panels

Installation Instructions. For the 18 Built-In Dishwasher and Front Color Panels Installation Instructions For the 18 Built-In Dishwasher and Front Color Panels Printed in USA 154232102 Before You Begin DO NOT INSTALL DISHWASHER UNTIL YOU HAVE READ ALL INSTRUCTIONS. FOR YOUR SAFETY,

More information

Can Am Commander 1000 Radiator Relocation Installation Instructions

Can Am Commander 1000 Radiator Relocation Installation Instructions Can Am Commander 1000 Radiator Relocation Installation Instructions What comes with the kit 2 CNC Machined Aluminum mounting brackets 2 pcs M6 x 1.0 x 60mm long SHCS 2 pcs M6 x 1.0 x75mm long SHCS 4 pc

More information

This site is based on a but applies to all 1971-on Saab 99 and Saab 900.

This site is based on a but applies to all 1971-on Saab 99 and Saab 900. by Mark Jeter updated: December 8, 2004 originally web-published June 27, 2001 This document shows how the original waterpump in a Saab "B" engine can be eliminated and replaced with a reliable, efficient

More information

569, 570, 571, 572 Series

569, 570, 571, 572 Series Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TID-0137_0A TECHNICAL INSTRUCTIONS AM Series Boiler Heat Exchanger Maintenance & Replacement For all models of AM Series Boilers, Including: Boilers: AM 399B AM 500B AM 750B AM 1000B Water Heaters: AM

More information

Welcome! Today s topic: Small Home Repairs. November 14, 2015

Welcome! Today s topic: Small Home Repairs. November 14, 2015 Welcome! Today s topic: Small Home Repairs November 14, 2015 Small Home Repairs Course Presented by Monique Johnson Environmental Green Solutions, LLC Objective Educate homeowners on basic technical skills

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK P/N 08T44-SNA-100 2008 MDX BII 37679 Issue Date AUG 2007 PARTS LIST Engine block heater Aluminum washer Heater harness Protective

More information

CapraLite. Owner s Manual. Milking Machines. Built by: Apparatus Mfg., Inc. 13 Commerce St Poughkeepsie, NY 12603

CapraLite. Owner s Manual. Milking Machines.  Built by: Apparatus Mfg., Inc. 13 Commerce St Poughkeepsie, NY 12603 CapraLite Milking Machines Owner s Manual www.capralite.com Built by: Apparatus Mfg., Inc. 13 Commerce St Poughkeepsie, NY 12603 Page 2 Getting your Machine ready Your machine is almost ready to use. For

More information

A HEATER KIT With Diesel Engine Connection Fittings

A HEATER KIT With Diesel Engine Connection Fittings A-12142 HEATER KIT With Diesel Engine Connection Fittings Figure 1 (General Layout and Parts I.D.) Page 1 of 6 Read these instructions and identify all components. Please retain these instructions for

More information

CBT Bowl & wrap replacement

CBT Bowl & wrap replacement CBT bowl & wrap replacement 2 CBT BOWL & WRAP REPLACEMENT Revision History rev. level 01_03.14.2012 rev. level 02_03.19.2012 rev. level 03_03.23.2012 rev. level 04_05.30.2013 NOTE: due to the fact that

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 30320 ENGINE BLOCK 2006 CIVIC HYBRID P/N 08T44-SVB-100 Issue Date SEP 2005 PARTS LIST Engine block heater Aluminium washer Heater harness

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK P/N 08T44-SVB-100 2011 CIVIC 4-DOOR Si All 44405 Issue Date AUG 2010 PARTS LIST Engine block heater Aluminum washer Heater

More information

Nilfisk Inc Winnetka Avenue North Minneapolis, MN REV.03( ) VF80189

Nilfisk Inc Winnetka Avenue North Minneapolis, MN REV.03( ) VF80189 Nilfisk Inc. 9435 Winnetka Avenue North Minneapolis, MN 55445 www.usviper.com REV.03(05-) VF8089 SAFETY PRECAUTIONS This machine is intended for commercial use. It is constructed for use in an indoor

More information

WATER DISPENSER INSTALLATION GUIDE

WATER DISPENSER INSTALLATION GUIDE WATER INSTALLATION GUIDE Before you begin: Your dispenser has two lines attached to it. The HOUSE WATER LINE attaches to your house s water supply. The REFRIGERATOR WATER LINE attaches to your refrigerator

More information

Chapter 3 Cooling, heating and ventilation systems

Chapter 3 Cooling, heating and ventilation systems 1 Chapter Cooling, heating and ventilation systems Contents Antifreeze - general information............................ 2 Auxiliary drivebelt check and renewal...............see Chapter 1 Coolant level

More information

569, 570, 571, 572 Series

569, 570, 571, 572 Series Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect

More information

Sanitise Syrup Lines & Valves. Taylor PH61 Cleaning every 14 days

Sanitise Syrup Lines & Valves. Taylor PH61 Cleaning every 14 days Taylor PH61 Cleaning every 14 days Drain the Syrup Lines Remove each syrup feed tube from syrup bottle and let excess syrup drain from the feed tube back into the syrup bottle. When flow of syrup from

More information

SD Bendix AD-1 and AD-2 Air Dryers

SD Bendix AD-1 and AD-2 Air Dryers SD-08-2403 Bendix AD-1 and AD-2 Air Dryers AD-1 AIR DRYER AD-2 AIR DRYER FIGURE 1 The air dryer collects and removes moisture and contaminants before the air reaches the first reservoir. It is distinctly

More information

Series 1140 and 1141 Temperature Regulators

Series 1140 and 1141 Temperature Regulators Hoffman Specialty Installation & Maintenance Instructions HS-504(E) Series 1140 and 1141 Temperature Regulators! CAUTION FOLLOW ALL INSTALLATION AND OPERATING INSTRUCTIONS. TURN OFF WATER OR STEAM BEFORE

More information

Platen Heater Pad Replacement

Platen Heater Pad Replacement Instruction Sheet P/N Platen Heater Pad Replacement WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related

More information

L24TWS. Beverage Tower Kit Components. L24TWD Lynx Beverage Kits Model L24TWS Single Tower and L24TWD Double Tower

L24TWS. Beverage Tower Kit Components. L24TWD Lynx Beverage Kits Model L24TWS Single Tower and L24TWD Double Tower Installation, Care and Use of Your Lynx Beverage Tower Kits MOM FRIENDLY. DAD READY. L24TWS Beverage Tower Kit Components L24TWD Lynx Beverage Kits Model L24TWS Single Tower and L24TWD Double Tower Introduction:

More information

Hot Chocolate Dispenser

Hot Chocolate Dispenser Hot Chocolate Dispenser Instruction manual Model: CN219-A AU Telephone Helpline: 1300225960 Safety Tips Position on a flat, stable surface. A service agent/qualified technician should carry out installation

More information

Detailed Cleaning Instructions

Detailed Cleaning Instructions NY Thermal Inc. Tel: (06) 67-6000 Toll Free: 1-800-688-27 Fax: 1-06-432-113 Web: www.ntiboilersl.com Email: info@ntiboilers.com Style Heat Exchanger occupants or, death. This boiler must be serviced by

More information

Mobile Milker. Filling the oil reservoir to HALF FULL

Mobile Milker. Filling the oil reservoir to HALF FULL 1 2 Mobile Milker Upon receiving the unit check if there is any visible damage to pump, motor etc... If there is any damage do not attempt to run the unit! Call 800-245-8222 for assistance. Preparing to

More information

Product Support Bulletin

Product Support Bulletin MODEL: SUBJECT: CONVENTIONAL, W/ C7 CAT ENGINE WEBASTO TSL-17 HEATER Body DATE: APRIL 13, 2004 INDEX: 6 PAGE: 1 OF 16 Before you start this procedure, perform Freightliner Service Bulletin #20-7 first.

More information

FLECK 5600 WATER SOFTENER INSTALLATION

FLECK 5600 WATER SOFTENER INSTALLATION FLECK 5600 WATER SOFTENER INSTALLATION Discount Water Softeners recommends using a licensed plumber to install your water softener. The following installation instructions are for use with the water softener

More information

INSTALLATION INSTRUCTIONS John Deere One Series; 1023E, 1025R and 1026R Models A HEATER KIT. Figure 1 (General Layout and Parts I.D.

INSTALLATION INSTRUCTIONS John Deere One Series; 1023E, 1025R and 1026R Models A HEATER KIT. Figure 1 (General Layout and Parts I.D. A-11978 HEATER KIT Figure 1 (General Layout and Parts I.D.) Read these instructions and identify all components. Please retain these instructions for future reference and parts ordering information. Refer

More information

As part of the V.I.P. family, you are entitled to the best protection by one of the most comprehensive warranties in the industry.

As part of the V.I.P. family, you are entitled to the best protection by one of the most comprehensive warranties in the industry. CONGRATULATIONS on your purchase of a Viper product, and welcome to the V.I.P. family. We appreciate your business and will do everything in our power to keep you happy with your purchase for many years

More information

specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST FORD TRUCK

specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST FORD TRUCK specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967-72 FORD TRUCK CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

DEUTSCH Bio-Master Bio-Max

DEUTSCH Bio-Master Bio-Max DEUTSCH D 8217-3029-02 Bio-Master Bio-Max SVENSKA S 4. 2. 1. 3. 4. 5. 3 S SVENSKA 7. 6. 8. 9. 10. 4 SVENSKA S 11. 12. 4. 13. 4. 15. 14. 5 GB ENGLISH SAFETY PRECAUTIONS GENERAL This symbol means WARNING.

More information

URBAN CRUISER AIR CONDITIONING (RHD) ENGLISH EUROPE

URBAN CRUISER AIR CONDITIONING (RHD) ENGLISH EUROPE URBAN CRUISER (RHD) AIR CONDITIONING ENGLISH EUROPE - 0 - IMPORTANT NOTICE DEFINITION OF TERMS INTRODUCTION This manual has been designed for technicians who are qualified and educated in the proper procedures

More information

FUN I / FUN U FUN I MCP / FUN U MCP FUN V / FUN V MCP

FUN I / FUN U FUN I MCP / FUN U MCP FUN V / FUN V MCP OPERATION INSTRUCTIONS MANUAL DUCTED FAN COILS UNIT FUN I / FUN U FUN I MCP / FUN U MCP FUN V / FUN V MCP 1 CONTENTS 1. GENERAL... 3 2. INSTALLATION... 4 3. AIR CONNECTIONS... 5 4. WATER CONNECTIONS...

More information

SAFETY PRECAUTIONS. 2) Before operating machine: - Make sure all safety devices are in place and operate properly.

SAFETY PRECAUTIONS. 2) Before operating machine: - Make sure all safety devices are in place and operate properly. TABLE OF CONTENTS Machine Components Safety Precautions Machine Set Up Machine Operation Machine Maintenance & Storage Troubleshooting Technical Specifications Parts Lists Wiring Diagram 1 2 3 3-4 5 6

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK P/N 08T44-SNA-101 2010 CIVIC 2 AND 4 DOOR (EXCEPT GX) AII 42477 Issue Date SEP 2009 PARTS LIST Engine block heater Aluminum

More information

51AKS I S O OWNER S MANUAL

51AKS I S O OWNER S MANUAL LLOYD'S REGISTER QUALITY ASSURANCE 51AKS I S O 9 00 1 OWNER S MANUAL This manual applies to the following models Stand-alone Split 51AKS 085--- 51AKS 010--- 51AKS 185--- 51AKS 013--- 51AKS 113--- 51AKS

More information

How To: PREPARATION REPLACE A KITCHEN SINK

How To: PREPARATION REPLACE A KITCHEN SINK Skill Level: INTERMEDIATE Give these projects a try if you're a confident DIYer with a good working knowledge of a variety of tools. They can take a day or more to complete. If you can build a birdhouse

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK P/N 08T44-SNA-100 2007 CIVIC 2 AND 4-DOOR (DX, LX, EX) AII 33542 Issue Date AUG 2006 PARTS LIST Engine block heater Aluminum

More information

MODEL A5-2 SOLVENT & WATER RECOVERY SYSTEMS (EXPLOSION PROOF UNITS)

MODEL A5-2 SOLVENT & WATER RECOVERY SYSTEMS (EXPLOSION PROOF UNITS) MODEL A5-2 SOLVENT & WATER RECOVERY SYSTEMS (EXPLOSION PROOF UNITS) FOR PROPER AND SAFE USE OF THIS CHEMCHAMP EQUIPMENT, PLEASE FOLLOW THIS DOCUMENT AND LOCAL AUTHORITY. KEEP THIS DOCUMENT FOR FUTURE REFERENCE.

More information

Cleaning Instructions for Burner, Pilot Assembly, and Emitter Screen. Series: LP Gas

Cleaning Instructions for Burner, Pilot Assembly, and Emitter Screen. Series: LP Gas Cleaning Instructions for Burner, Pilot Assembly, and Emitter Screen Series: 220000-450000 LP Gas For assistance call 1.800.762.1142. Bottle brush Brass brush Heavy-duty pipe cleaners Non-abrasive Scouring

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory ENGINE BLOCK Application 2010 INSIGHT Publications No. AII 40879 Issue Date MARCH 2009 PARTS LIST Engine Block Heater Kit P/N 08T44-SNA-101 Engine block heater Engine

More information

TT /97 WARNING WARNING WARNING INSTALLATION INSTRUCTIONS

TT /97 WARNING WARNING WARNING INSTALLATION INSTRUCTIONS TT-116 2/97 INSTALLATION INSTRUCTIONS Original Issue Date: 2/97 Model: 900/1000 kw Market: Industrial Subject: Block Heater Kits PA-28648, PA-28648-SD The block heater kit heats engine coolant, making

More information

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST FORD PICKUP

PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST FORD PICKUP specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1960-66 FORD PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK ELEMENT AII 24284 Issue Date DEC 2002 PARTS LIST Engine block heater Aluminum washer Heater harness Protective cap 20 Long

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory ENGINE BLOCK V6 P/N 08T44-SNA-101 Application 2008 ACCORD 2- AND 4-DOOR Publications No. AII 36800-38336 Issue Date NOV 2007 PARTS LIST ENGINE BLOCK Engine block heater

More information

Group 7 COOLING SYSTEM CONTENTS

Group 7 COOLING SYSTEM CONTENTS Group 7 COOLING SYSTEM CONTENTS COOLING SYSTEM 1 Paragraph Page Engine Water Temperature Gauge 9 7 Instrument Panel Unit 7 Temperature Sending Unit ; 8 Electrical Circuit (Testing) 8 Pressure Testing Cooling

More information

Patterson/AMT Inline Circulator Pump Refer to pump manual for General Operating and Safety Instructions.

Patterson/AMT Inline Circulator Pump Refer to pump manual for General Operating and Safety Instructions. Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect

More information

HEATING AND AIR CONDITIONING

HEATING AND AIR CONDITIONING WJ HEATING AND AIR CONDITIONING 24-1 HEATING AND AIR CONDITIONING TABLE OF CONTENTS page SERVICE PROCEDURES REFRIGERANT OIL LEVEL...1 REFRIGERANT RECOVERY....1 REFRIGERANT SYSTEM CHARGE...1 REFRIGERANT

More information

DIESEL/PARAFFIN HEATERS

DIESEL/PARAFFIN HEATERS DIESEL/PARAFFIN HEATERS MODEL NO: XR80, XR110, XR160, XR210 PART NO: 6931004, 6931006, 6931008, 6931012 OPERATION & MAINTENANCE INSTRUCTIONS LS0814 INTRODUCTION Thank you for purchasing this CLARKE product.

More information

an ISO 9001:2015 Registered Company

an ISO 9001:2015 Registered Company an ISO 9001:2015 Registered Company Mark IV (672001-VHY) 18865 Goll St. San Antonio, TX 78266 Phone: 800-862-6658 Sales: sales@vintageair.com Tech Support: tech@vintageair.com www.vintageair.com 902001-VHY

More information

LG G2 Super Cool C7 Radiator

LG G2 Super Cool C7 Radiator LG G2 Super Cool C7 Radiator THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 Parts Inventory: 1. Radiator 2. 170 thermostat (optional) Tools Needed: 1. Drain pan 2.

More information

This guide will be posted in several chunks so please don't post till im done, cheers.

This guide will be posted in several chunks so please don't post till im done, cheers. vx220.org.uk > General Discussion > VX220 Discussion Radiator Replacement Guide Options SteveA Jan 10 2007, 00:47 Post #1 This guide will be posted in several chunks so please don't post till im done,

More information

OWNER S MANUAL AND INSTALLATION GUIDE PLEASE READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING INSTALLATION

OWNER S MANUAL AND INSTALLATION GUIDE PLEASE READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING INSTALLATION ClearChoice Economy Under Sink Drinking Water System OWNER S MANUAL AND INSTALLATION GUIDE PLEASE READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING INSTALLATION Congratulations on the purchase of your ClearChoice

More information

BC BRONCOS AIR CONDITIONING UNIT

BC BRONCOS AIR CONDITIONING UNIT BC BRONCOS AIR CONDITIONING UNIT CAUTION If you are not familiar with the principals of air conditioning, have an authorized air conditioning technician evacuate and charge the system. Serious damage to

More information

Installation Instructions

Installation Instructions Installation Instructions For the 18" Built-In Dishwasher Sears, Roebuck and Co. Sears Canada, Inc. Hoffman Estates, IL 60179 U.S.A. Toronto, Ontario, Canada M5B 2B8 154435201 Before You Begin DO NOT INSTALL

More information

COMPRESSED AIR DRYER. SAFETY... Page 2 MAINTENANCE... Page 5. INSTALLATION... Page 3 PARTS AND KITS... Page 6

COMPRESSED AIR DRYER. SAFETY... Page 2 MAINTENANCE... Page 5. INSTALLATION... Page 3 PARTS AND KITS... Page 6 OWNERS MANUAL BOSS COMPRESSED AIR DRYER Distributed by Air & Vacuum Process, Inc. Phone: 281-866-9700 Fax: 281-866-9717 Email: sales@airvacuumprocess.com SAFETY... Page 2 MAINTENANCE... Page 5 INSTALLATION...

More information

OWNER S MANUAL. Models: Herkules Equipment Corporation 2760 Ridgeway Court Walled Lake, MI USA Fax

OWNER S MANUAL. Models: Herkules Equipment Corporation 2760 Ridgeway Court Walled Lake, MI USA Fax Part# 1000692 7/12/99 tn INSTRUCTIONS This manual contains important information concerning the installation and operation of the gun washers listed at the right. Read manual thoroughly and keep for future

More information

Tornado Operations & Maintenance Manual

Tornado Operations & Maintenance Manual Tornado Industries, LLC 333 Charles Court West Chicago, IL 60185 www.tornadovac.com Tornado Operations & Maintenance Manual MODEL NO. 99414 Form No. L9740AB Tornado Industries, LLC. All rights reserved

More information

Tornado Operations & Maintenance Manual

Tornado Operations & Maintenance Manual TORNADO INDUSTRIES 7401 W. LAWRENCE AVENUE CHICAGO, IL 60706 (708) 867-5100 FAX (708) 867-6968 www.tornadovac.com Tornado Operations & Maintenance Manual MODEL NO. 99690 BD 22/14, 99720 BD 26/14 L9722

More information

A/C-HEATER SYSTEM - MANUAL

A/C-HEATER SYSTEM - MANUAL A/C-HEATER SYSTEM - MANUAL 1986 Isuzu Trooper II 1986 A/C-HEATER SYSTEM Isuzu A/C-Heater Systems - Manual P UP, Trooper II * PLEASE READ THIS FIRST * CAUTION: When discharging air conditioning system,

More information

Unpacking and removing shipping bolts. Connecting the drain line Leveling the washer Connecting to the power supply

Unpacking and removing shipping bolts. Connecting the drain line Leveling the washer Connecting to the power supply 11 INSTALLATION Installation Overview Choosing the proper location Unpacking and removing shipping bolts Connecting the water line Connecting the drain line Leveling the washer Connecting to the power

More information

The Handle The Flush Valve And the Ballcock

The Handle The Flush Valve And the Ballcock Replace Toilet Tank Parts All of the parts inside your toilet are used many times a day, and are constantly under water. This causes a lot of damage on these parts, but thankfully enough they re very easy

More information

HydroFlux Welder Torch System T0-102 / T0-103

HydroFlux Welder Torch System T0-102 / T0-103 HydroFlux Welder Torch System T0-102 / T0-103 Setting Up The HydroFlux 1. Location - The HydroFlux Welder must be placed on a level surface with adequate ventilation. We recommend a minimum of 4 inches

More information

CABS/BLADES/ SPREADERS/ACCESSORIES

CABS/BLADES/ SPREADERS/ACCESSORIES JOHN DEERE 3000 SERIES (4200/4300/4400) (4210/4310/4410) (3120/3320/3520/3720) JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) OPTIONAL AUXILIARY HEATER INSTALLATION (p/n

More information

INSTALLATION PROCEDURE 2011 Navistar MaxxForce 13L

INSTALLATION PROCEDURE 2011 Navistar MaxxForce 13L Evans Cooling Systems, Inc. 1 Mountain Rd. Suffield, CT 06078 INSTALLATION PROCEDURE 2011 Navistar MaxxForce 13L CAUTIONARY NOTE: DO NOT FLUSH COOLING SYSTEM WITH WATER! 1. Supplies, information, and special

More information