Installation Instructions & Operating Manual IMPORTANT

Transcription

1 Installation Instructions & Operating Manual IMPORTANT These instructions should be read carefully and retained for future reference

2 TABLE OF CONTENTS SECTION 1: WARNINGS & ELECTRIC SPECIFICATIONS 1.1 Important Safety Instructions Specifications 3 SECTION 2: INSTALLATION & PREPARATION 2.1 Unpacking the Fireplace Check Your Components Parts and Hardware 5-6 SECTION 3: WALL MOUNTED INSTALLATION 7-9 SECTION 4: FREE STANDING INSTALLATION SECTION 5: OPERATING INSTRUCTIONS SECTION 6: MAINTENANCE 6.1 Remote Handset Battery Replacement Resetting the Thermal Cutout Switch Cleaning & Maintenance Environment 15 SECTION 7: WARRANTY 16 This electric fire is not intended for use as a primary heat source and should not be factored as such in residential heating calculations _4 2

3 SECTION 1 WARNING & ELECTRIC SPECIFICATIONS 1.1 Important Safety Instructions When using electrical appliances, simple precautions should always be followed to reduce the risk of personal injury, electrical shock and reduce the risk of fire: If the appliance is damaged, do not install or operate the product, check with the supplier. Do not use the product outdoors Do not use the product in the immediate surrounds of a bath, shower or swimming pool Do not locate the heater immediately below a fixed socket outlet or connection box In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device,such as a timer, or connected to circuit that is regularly switched on and off by utility In the event of a fault unplug the heater Unplug the heater when not required for long periods The appliance must be positioned so that the plug is accessible. If the supply cord is damaged, it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard Do not cover the heater. Do not place material or garments on the heater or obstruct the air circulation around the heater, for instance by curtains or furniture as this could cause overheating and a fire risk. Ensure that furniture, curtains and other fabrics and combustible materials are positioned no closer than 1 metre from the heater Children should not play with the appliance Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance. Cleaning and user maintenance shall not be made by children with out supervision This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present _4

4 1.2 SPECIFICATIONS Voltage Total Amps Total Watts Heater Rating Dimensions Weight V AC, 50 Hz 6.5 AMP 1500 Watts 1480 Watts Length: 820mm, Width: 110mm, Height: 343mm 13.4 Kg Note: This heater must be earthed. If in any doubt consult an electrician or suitable competent person SECTION 2 INSTALLATION & PREPARATION 2.1 Unpacking the Fireplace WARNING: The product inside the packaging includes a glass panel please use extreme caution when handling the glass. If in any doubt seek assistance to prevent damage and personal injury. Open the packaging and remove the contents carefully Retain the original packaging for future storage and transportation Keep plastic wrapping away from children Any waste material should be recycled where possibleoperate the heater WARNING Keep plastic wrapping away from children 2.2 Check Your Components Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and assembly steps are grouped for free standing or wall mounted use. Check the parts list to make sure nothing is missing. Free-Standing Installation: You will need Part A (Firebox) Part B (Glass Panel) Box 1 (Remote Control) Box 2 (Coal Bed Decorations) Box 3 (Pedestal Leg) Box 4 (Pedestal Base) Wall-Hanging Mode: You will need Part A (Firebox) Part B (Glass Panel) Part C (Wall Bracket) Part 6 (Thumb Screws) Box 1 (Remote Control) Box 2 (Coal Bed Decorations) Box 5 (Screws) _4 4

5 2.3 Parts and hardware A Firebox ( 1 ) B Front Glass Panel ( 1 ) NOTE: The wall mount bracket (C) is attached to the back of the firebox (A) by two thumb screws (6). C Wall Mount Bracket ( 1 ) 6 Thumb Screws ( 2 ) 6 6 C A NOTE: Unscrew both thumbscrews (6) from the top of the firebox (A). keep the thumb screws. Remove the wall mount bracket (C) from the firebox whether you will use the unit in free-standing or wall-hanging mode _4

6 Parts and hardware GENERAL Box 1: Remote Control & Machine Screws Box 1 Remote Control & Machine Screws Box 2: Decorative Glass Box 2 Decorative Glass 2 M4x8 Machine screws ( 2 ) RC Remote Control ( 1 ) RC Battery ( 1 ) D Decorative Glass ( 1 set ) Parts PARTS & and hardware: hardware: FREE-STANDING Free standing MODE mode Box 3 Pedestal Leg Parts and Hardware Box 3: Pedestal Leg Parts and Hardware Box 4 Pedestal Base Box 4: Pedestal Base E Pedestal Leg ( 1 ) G Pedestal leg Cover ( 1 ) 1 M5x12 Machine Screws ( 10 ) F Pedestal Base Assembly ( 1 ) PARTS & hardware: WALL-hANGING MODE Parts and hardware: Wall MOUNTED Mode Box 5 Wall Hanging Hardware Box 5: Wall Hanging Hardware 3 M5x40 Wood Screws ( 4 ) 4 Φ8x40 Drywall Anchors ( 4 ) _4 6

7 SECTION 3 WALL MOUNTED INSTALLATION Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing a location ensure that the general instructions are followed. For best results, install out of direct sunlight. Make sure that the plug or switched fused spur is accessible after the electric fire is fitted. The appliance should be located close to a suitable mains socket to enable connection. The electrical socket must be easily accessible to allow disconnection. WARNING! Keep drapery and other furnishings at least 1 metre from the front and sides of the electric fireplace. Fig. 1 Clearance to Combustibles sides 50 mm floor 110 mm Top 0 mm Back 0 mm INSTALL YOUR FIREPLACE (WALL MOUNTED) STEP 1 Choose a flat wall and then put the bracket on the position where you want to install the fire. Mark the 4 holes carefully from the holes on the bracket (see Fig. 2) STEP 2 Remove the bracket and then drill 4 x Φ8mm holes on the wall. Use appropriate plugs and fixings for your wall type. (see Fig. 3). STEP 3 Fix the bracket by 4x M5 8 screws (See Fig. 4) STEP 4 With the firebox (A) at an angle, fit the slots in the back of firebox (A) over the hooks on the wall mount bracket, and carefully press the top of the firebox against the wall mount bracket. The slots at the top edge of the firebox should slide over the wall mount bracket tabs. Hold the firebox in place and thread the thumb screws (6) through the holes in the firebox and into the wall mount bracket tabs. Tighten both thumb screws and make sure the firebox is secure to the wall. (See Fig. 5, 6 and 7) STEP 5 Carefully arrange the decorative glass (D) along the inset window ledge at the front of the firebox. Use care when moving the fireplace to prevent the decorative glass from sliding about. (See Fig. 8 and 9) _4

8 WARNING The next step requires installation of a glass panel. The manufacturer recommends that two adults install the glass panel. Always use caution when handling glass. Failure to do so could result in injury or property damage. STEP 6 Set both hooks of the front glass panel (B) into the slots at the top front edge of the firebox (A). Press the two posts of the glass panel into the locking slots near the lower corners of the front firebox panel. Thread the M4x8 machine screws (2) through the hooks and into the threaded holes in the firebox. Check the glass panel alignment and securely tighten the screws with a Phillips screwdriver. (Fig. 10) Fig. 2 Fig. 3 Fig _4 8

9 Fig. Fig. 5 5 Fig. Fig. 66 Fig. 7 Fig. 8 Fig. 8 Fig. 9 Fig. 9 Fig _4

10 SECTION 4 FREE STANDING INSTALLATION INSTALL YOUR FIREPLACE (FREE STANDING) Ensure fire is unplugged from mains before proceeding with any installation STEP 1 STEP 2 STEP 3 Lay the firebox (A) on its back. Align the holes in the pedestal leg (E) with the threaded inserts in the firebox. Thread one M5x12 machine screw (1) through each hole in the pedestal leg and into the threaded inserts. Check the leg alignment. Tighten securely with a Phillips screwdriver (Not supplied). (Fig. 11) The pedestal leg cover (G) into the pedestal base assembly (F). Push into place. (Fig. 12) Lay the firebox on its back so the pedestal leg (E) hangs over the edge of a table or with assistance lift the bottom edge of the firebox. Slide the pedestal leg cover and base (F/G) over the pedestal leg (E). Make sure the power supply cord comes out from the notch in the pedestal leg cover. Thread one M5x12 machine screw (1) through each hole in the pedestal base, into the threaded holes in the pedestal leg. Tighten securely with a Phillips screwdriver (Not Supplied). (Fig. 13) WARNING The next step requires handling of small glass pieces! Use caution when handling. Failure to do so could result in personal injury or damage to property. Always keep the small glass pieces out of reach from children and ensure no pieces are left out as these could be a choking hazard. STEP 4 Stand the fireplace up and set it on a sturdy level surface at or near where you plan to use it. Carefully arrange the decorative glass (D) along the inset window ledge at the front of the firebox. Use care when moving the fireplace to prevent the decorative glass from sliding about. (see Fig. 14). WARNING The next step requires installation of a glass panel. The manufacturer recommends that two adults install the glass panel. Always use caution when handling glass. Failure to do so could result in injury or property damage. STEP 5 1. Carefully set both hooks of the front glass panel (B) into the slots at the top front edge of the firebox (A). 2. Press the two posts of the glass panel into the locking slots near the lower corners of the front firebox panel. Thread the M4x8 machine screws (2) through the glass panel hooks and into the threaded holes in the firebox. Partially tighten by hand. Check the alignment of the glass panel and securely tighten the screws with a Phillips screwdriver (Not supplied). (Fig. 15) Fig /08/ _ _4 10

11 Fig. 11 Fig. 12 Fig. 12 Fig. 13 Fig. 13 Fig. 14 Fig. 14 Fig. 15 Fig. 15 Fig. 16 / _ _4

12 SECTION 5 OPERATING INSTRUCTIONS POWER Make sure the ON/OFF switch, located on the control panel, is in the OFF position. Plug the power cord into a 230~240 Volt 13 Amp power supply. Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit. Methods of Operation To use both remote and manual functions the manual on/off switch must be in ON position. CONTROL PANEL: Located on the right side panel of the fireplace (see figure below). Controls ON/OFF, FLAME EFFECT, LED BACKLIGHTS, and HEATER. The control panel will not provide you with all function control. Please use the remote hand set to carry out all functions. REMOTE CONTROL (Battery included): Controls the FLAME EFFECT, LED BACKLIGHTS, HEATER, THERMOSTAT, and TIMER _4 12

13 CONTROL PANEL OPERATION BUTTON FUNCTION ACTION & INDICATION ON/OFF FLAME HEATER ON: Enables control panel functions. Remote control is enabled. OFF: Disables all functions. Remote control will not function. FLAME button: Controls the flame effect and LED backlight effects. FLAME button: Enables the heater. The heater button will only work if the flame effect is ON. NOTE: The FLAME effect stays on until the ON/OFF button is turned OFF. HEATER button: Turns heater on and off. NOTE: The HEATER button only works when the flame effect is ON. If the flame effect is OFF, the heater will not turn on. NOTE: To prevent overheating, the heater fans will blow cool air for 8-10 seconds before the heater comes on, and after the heater turns off. NOTE: Thermostat settings are controlled by the REMOTE CONTROL (see Page 15). 1. Press ON. The unit will beep. Power turns ON, and all functions are enabled. 2. Press OFF. The unit will beep. Power and all functions turn OFF. 1. Press once. Flame effect: High. 2. Press again. Flame effect: Medium. 3. Press again. Flame effect: Low. 4. Press to cycle through LED backlight effects (Orange and Blue). Flame effect stays on. 5. Press again. Backlights turn off. 1. Press once. The unit will beep. The heat symbol on the digital display will glow, and then turn off. Cool air will blow for 8-10 seconds. The heater will then click on and blow hot air. 2. Press again. The unit will beep. The heater will turn OFF. The fan will blow for 10 seconds to allow the air and the heater to cool down. The fan will then turn OFF. Please note: When the heater is first turned on, a slight odor may be present. This is normal and should not occur again unless the heater is not used for a long period of time. REMOTE CONTROL OPERATION BUTTON FUNCTION ACTION & INDICATION ON/OFF FLAME The CONTROL PANEL switch must be ON to use the REMOTE CONTROL. The ON/OFF button turns on the flame and enables all functions. Other functions will only work when this is ON The FLAME button allows you to select one of four flame effects. It does not control the back lights. While the ON/OFF is ON, the flame is ON. 1. Beep. Flame effect high intensity. All other functions are now enabled. 2. Beep. During operation, when switched OFF, all functions will turn OFF. 1. Flame intensity - high. 2. Flame intensity - medium. 3. Flame intensity - low. 4. Flame effect - multicolor _4

14 BUTTON FUNCTION ACTION & INDICATION HEATER TEMP TIMER The HEATER button controls the left and right heaters. There are four levels: Low (Left), Low (Right), High (Both), and Off. The heater only works when the flame effects are ON. If the flame effects are OFF, the heater will not turn on. To prevent overheating, the heater fans will blow cool air for 8-10 seconds each time the heater is turned ON or OFF. The TEMP button controls the thermostat. The thermostat will ONLY work when the heater is ON. The thermostat will automatically turn the heaters (left and right) ON and OFF to maintain the selected temperature setting. If the HEATER button is pressed while the thermostat is ON, the thermostat will be turned OFF, and the digital display will go blank. The heaters will now be controlled by the HEATER button, not the thermostat. Press TEMP to restart the thermostat. The TIMER button controls the timer settings, which will shut the fireplace OFF when the timer reaches 0.0. Settings are by the half-hour: 0.0 (off), 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0 H. 1. Heat symbol on digital display glows; then turns off. 2. Beep. Cool air blows for 10 seconds; then heater turns ON and blows hot air. 3. Beep. Heater turns OFF. Fan blows for 10 seconds to allow air and heater to cool down, and then turns off. 1. Beep. Digital display shows ON, the thermostat settings OFF (default). Digital display will shut off after 10 seconds. It will light up each time the button is pushed. 2. Beep. Thermostat setting will increase. Digital display: Beeps. Thermostat settings will increase by 1 up to 28 maximum. The digital display will show each setting. 13. Beep. Thermostat and display ON 1. Beep. Digital display:0.0h Beeps. Timer settings will increase from 0.5H up to 5H. The digital display will show each setting, and then go blank after 10 seconds. BACK LIGHT The BACK LIGHT button controls the LED light strips at the rear edges of the fireplace. The five settings are OFF, Yellow, Blue, Yellow/Blue, and Multicolor. The back lights work with or without the other features being turned on. 1. Beep. Back light - yellow 2. Beep. Back light - blue 3. Beep. Back light - yellow + blue 4. Beep. Back light - alternating colors 5. Beep. Back light turns OFF _4 14

15 SECTION 6 MAINTENANCE WARNING Before any maintenance and/or cleaning the exterior of the fireplace, disconnect the unit from the power supply and leave until cooled off. 6.1 Remote Handset Battery Replacement Replace with one CR2032 battery. Make sure the battery is installed correctly in the remote control. 6.2 RESETTING THE THERMAL CUTOUT SWITCH The appliance is fitted with an Electronic Safety Control (E.S.). This is a safety device, which switches off the fire if, for any reason, the appliance overheats, e.g. when covered. If the heater stops operating whilst the flame effect continues normally, this indicates that the E.S. Control is in operation. The E.S. Control can only be re-set after the appliance has cooled down, in order to re-set the E.S. Control proceed as follows: Switch off the appliance (Manual On/Off switch) and leave for approximately minutes. Remove any obstruction to the fan heater outlet or fan blades etc. Make sure that the power supply is disconnected at the plug socket outlet whilst you do this. Switch on appliance and the E.S. Control will re-set. Ensure that the appliance is functioning correctly. If the E.S. Control operates again, the appliance should be checked by a competent Electrician. 6.3 CLEANING THE FIREPLACE You can clean the exterior of the fireplace with a soft, damp, lint-free cloth. Do not use cleaning or polishing products. To remove fingerprints or other marks on the front glass panel, use a soft, damp, lint-free cloth with a good quality household glass cleaner. The front glass panel should always be completely dried with a clean, lint-free cloth or paper towel. CAUTION Do not use abrasive cleaners on the glass panel. Do not spray liquids directly onto any surface of the unit. WARNING An authorised service representative should perform any other servicing. The area around the fire should be kept free of any materials such as lint or house dust (i.e. animal hair/ carpet fibers) that could be drawn into the internal workings of the appliance and hence affect the performance. We recommend that you clean around the fan grille housing at regular intervals. This can be done using standard vacuum cleaner and suitable attachment. 6.4 ENVIRONMENT Meaning of crossed out wheeled dustbin: Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposals at least free of charge _4

16 SECTION 7 WARRANTY Be Modern Group (the Company ) provide a twelve month guarantee in respect of electric fire (the Product ) ranges. 1. The twelve month Guarantee applies to: All Products in the ranges manufactured by the Company (but subject to exceptions below); where The Product has been purchased and installed within the UK and in respect of The initial installation; and in favour of The original Purchaser 2. Proof of purchase must be retained by the Purchaser 3. The twelve month Guarantee does not apply to: Damage or inferior workmanship practices while the Product is being installed Damage caused by the mis-use of the Product or where normal standards of care and use have not been complied with. Damage through a malfunction or an inadequately installed electric fire. Damage or defects due to, mis-use, accident or unauthorized alterations. During the twelve month after the Product has been supplied, the Guarantee covers the making good (whether by repair or replacement at the company s option) of defects arising from defective manufacture of materials of Product covered in paragraph (1), all at no cost to the Purchaser. This Guarantee does not affect your statutory rights On requiring service contact the retailer who supplied your product who will assist you and advise you as necessary. Customer Services Tel: (0191) Fax: (0191) This fire complies with the European Safety Standards (LVD) EN and the European Electro Magnetic Compatibility (EMC) En55015, EN and EN which covers the essential requirements of the EEC Directives and 89/ _4 16