Product Data. Efficiency S S S Sound S Comfort S. S S S S S S Durability. WeatherArmort protection package: S S S

Transcription

1 Comfortt13 Air Conditioner for Coastal Applications with r Refrigerant Product Data the environmentally sound refrigerant Carrier s Air Conditioners with r refrigerant provide a collection of features unmatched by any other family of equipment. The 24ABB has been designed utilizing Carrier s refrigerant. The environmentally sound refrigerant allows you to make a responsible decision in the protection of the earth s ozone layer. This product has been designed and manufactured to meet Energy tarr criteria for energy efficiency when matched with appropriate coil components. Refer to the combination ratings in the Product Data for system combinations that meet Energy tarr guidelines. NOTE: Ratings contained in this document are subject to change at any time. Always refer to the AHRI directory ( for the most up -to -date ratings information. INDUTRY LEADING FEATURE / BENEFIT Efficiency ound Comfort EER/ EER Microtube Technologyt refrigeration system Indoor air quality accessories available ound level as low as 75 dba supports Thermidistatt or standard thermostat controls Reliability Durability r refrigerant - environmentally sound, won t deplete the ozone layer and low lifetime servce cost. Front -seating service valves croll compressor Internal pressure relief valve Internal thermal overload Filter drier Balanced refrigeration system for maximum reliability WeatherArmort protection package: olid, durable sheet metal construction Dense wire coil guard Baked -on powder paint on all sides ArmorPlate Condenser Coil Aluminum fin material is pre -coated on both sides with a corrosion protective epoxy phenolic coating. Applications Long -line - up to 250 feet (76.20 m) total equivalent length, up to 200 feet (60.96 m) condenser above evaporator, or up to 80 ft. (24.38 m) evaporator above condenser (ee Longline Guide for more information.) Low ambient (down to -20_F/-28.9_C)) with accessory kit

2 MODEL NUMBER NOMENCLATURE N N A A A/N N N N A/N A/N A/N N N 2 4 A B B C Product eries Product Family Tier Major eries EER Cooling Capacity 24=AC A=RE AC B=Comfort B= 3=13 EER C=Coastal Variations Open Open Voltage eries 0=Not Defined 0=Not Defined 3=208/ = Original eries the environmentally sound refrigerant Use of the AHRI Certified TM Mark indicates a manufacturer s participation in the program For verification of certification for individual products, go to This product has been designed and manufactured to meet Energy tar criteria for energy efficiency when matched with appropriate coil components. However, proper refrigerant charge and proper air flow are critical to achieve rated capacity and efficiency. Installation of this product should follow all manufacturing refrigerant charging and air flow instructions. Failure to confirm proper charge and air flow may reduce energy efficiency and shorten equipment life. TANDARD FEATURE Feature Refrigerant X X X X X X X Maximum EER Rating croll Compressor X X X X X X X DenseWireCoilGuard X X X X X X X FieldInstalledFilterDrier X X X X X X X Front eating ervice Valves X X X X X X X Internal Pressure Relief Valve X X X X X X X Internal Thermal Overload X X X X X X X Long Line capability X X X X X X X Low Ambient capability with Kit X X X X X X X X = tanadard 2

3 REFRIGERANT PIPING LENGTH LIMITATION Liquid Line izing and Maximum Total Equivalent Lengths { for Cooling Only s with r Refrigerant: The maximum allowable length of a residential split system depends on the liquid line diameter and vertical separation between indoor and outdoor units. ee Table below for liquid line sizing and maximum lengths : ize Liquid Line Connection Liquid Line Diam. w/ TXV ( ) Maximum Total Equivalent Length Outdoor Unit BELOW Indoor Unit Refrigerant Maximum Total Equivalent Length{: Outdoor unit BELOW Indoor Vertical eparation ft (m) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) 1/ /16 250* 250* 250* 250* 250* 250* 250* 225* * 250* 250* 250* 250* 250* 250* 250* 250* 1/ /16 250* 250* 250* 250* 250* 225* * 250* 250* 250* 250* 250* 250* 250* 250* 1/ / * * 250* 250* 250* 250* 250* 250* 250* 250* 5/ //8 250* 250* 250* 250* 250* 250* 250* 250* 250* 5/ * 250* 250* 250* 250* 250* 250* 250* * 250* 250* 250* 250* 250* * 250* 250* 225* * Maximum actual length not to exceed 200 ft (61 m) { Total equivalent length accounts for losses due to elbows or fitting. ee the Long Line Guideline for details = outside acceptable range ize Liquid Line Connection Liquid Line Diam. w/ TXV 25 (7.6) Maximum Total Equivalent Length Outdoor Unit ABOVE Indoor Unit Refrigerant Maximum Total Equivalent Length{: Outdoor unit ABOVE Indoor Vertical eparation ft (m) ( ) ( ) ( ) ( ) ( ) ( ) ( ) 1/ * 250* 250* 250* 250* 250* 250* 5/16 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 1/ * 250* 250* 250* 5/16 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 1/ /16 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 5/16 225* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 5/ * 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* 250* * Maximum actual length not to exceed 200 ft (61 m) { Total equivalent length accounts for losses due to elbows or fitting. ee the Long Line Guideline for details = outside acceptable range 3

4 Liquid Line ize REFRIGERANT CHARGE ADJUTMENT Charge oz/ft (g/m) 0.60 (17.74) (Factory charge for lineset = 9 oz / g) 5/ (11.83) 1/ (7.98) Units are factory charged for 15 ft (4.6 m) of liquid line. The factory charge for lineset 9 oz. When using other length or diameter liquid lines, charge adjustments are required per the chart above. Charging Formula: [(Lineset oz/ft x total length) (factory charge for lineset)] = charge adjustment Example 1: has 15 ft of line set using existing 1/4 liquid line. What charge adjustment is required? Formula: (.27 oz/ft x 15ft) (9 oz) = (-4.95) oz. Net result is to remove 4.95 oz of refrigerant from the system Example 2: has 45 ft of existing 5/16 liquid line. What is the charge adjustment? Formula: (.40 oz/ft. x 45ft) (9 oz.) = 9 oz. Net result is to add 9 oz of refrigerant to the system LONG LINE APPLICATION An application is considered Long Line, when the refrigerant level in the system requires the use of accessories to maintain acceptable refrigerant management for systems reliability. ee Accessory Usage Guideline table for required accessories. Defining a system as long line depends on the liquid line diameter, actual length of the tubing, and vertical separation between the indoor and outdoor units. For Air Conditioner systems, the chart below shows when an application is considered Long Line. AC WITH PURONr REFRIGERANT LONG LINE DECRIPTION ft (m) Beyond these lengths, long line accessories are required Liquid Line ize Units On ame Level Outdoor Below Indoor Outdoor Above Indoor 1/4 No accessories needed within allowed No accessories needed within allowed lengths lengths 175 (53.3) 5/ (36.6) 50 (15.2) vertical or 120 (36.6) total 120 (36.6) 80 (24.4) 35 (10.7) vertical or ) total 80 (24.4) Note: eelonglineguidelinefordetails VAPOR LINE IZING AND COOLING CAPACITY LO Acceptable vapor line diameters provide adequate oil return to the compressor while avoiding excessive capacity loss. The suction line diameters shown in the chart below are acceptable for AC systems with refrigerant: Unit Nominal ize (Btuh) Vapor Line izing and Cooling Capacity Losses r Refrigerant 1 -tage Air Conditioner Applications Maximum Liquid Line Diameters (In. OD) Vapor Line Diameters (In. OD) ( ) ( ) Cooling Capacity Loss (%) Total Equivalent Line Length ft. (m) ( ) ( ) ( ) ( ) ( ) ( ) ( ) 018 1/ tage 5/ / / tage 3/ / / tage 3/ / / tage 3/ / / tage 7/ / / tage 7/ / / tage 7/ / Applications in this area may be long line and may have height restrictions. ee the Residential Piping and Long Line Guideline.

5 PHYICAL DATA UNIT IZE ERIE Operating Weight lb (kg) (58.1) (60.3) (70.3) (75.7) (85.3) (89.4) (102.7) hipping Weight lb (kg) Compressor Type REFRIGERANT Control Charge lb (kg) 159 (72.1) 4.1 (1.86) 167 (75.7) 5.1 (2.31) 193 (87.3) 205 (92.8) croll 225 (102.1) r (R---410A) TXV (r Hard hutoff) (2.63) (3.08) (2.81) Propeller Type, Direct Drive Vertical 235 (106.6) 7.3 (3.31) 267 (120.9) COND FAN Air Discharge Air Qty (CFM) Motor HP 1/12 1/10 1/5 1/5 1/5 1/5 1/4 Motor RPM COND COIL Face Area (q ft) Fins per In Rows Circuits VALVECONNECT.(In.ID) Vapor 5/8 5/8 3/4 3/4 7/8 7/8 7/8 Liquid REFRIGERANT TUBE (In. OD) Rated Vapor* 5/8 3/4 7/ /8 Vapor 3/4 7/ / /8 Liquid ( ft / m) Tube Length) Liquid (For Long---Line applications) * Units are rated with 25 ft (7.6 m) of lineset length. ee Vapor Line izing and Cooling Capacity Loss table when using other sizes and lengths of lineset Note: ee unit Installation Instruction for proper installation. ACCEORY THERMOTAT PART NUMBER PROGRAM GA ELECTRIC HEAT PUMP HEAT COOL TC --- PAC Day 1 1 TC --- NAC01 NP 1 1 TCNAC01 NP 1 1 THERMOTAT ACCEORIE PART NUMBER DECRIPTION THERMOTAT UED WITH TTATXXCNV10 Thermostat Conversion Kit (4 to 5 wire) pack All Carrier branded thermostats TX --- LBP01 LargeDecorativeBackplate TP --- Pxx, TP --- Nxx, TC --- Pxx TX ---MBP01 Medium Decorative Backplate TC ---Nxx, TB ---Pxx 9.9 (4.49) ACCEORIE ORDER NUMBER DECRIPTION ize --- Voltage & eries KAAFT0101AAA FREEZE THERMOTAT X X X X X X X KAATD0101TDR TIME DELAY RELAY X X X X X X X KAAW0101AAA WINTER TART X X X X X X X KALA LOW AMBIENT PW X X X X X X X KALA0601AAA{ MOTORMATER 230V X X X X X X X HC32GE234 MOTOR FAN BALL BEARING X HC34GE239 MOTOR FAN BALL BEARING X HC38GE219 MOTOR FAN BALL BEARING X X HC40GE228 MOTOR FAN BALL BEARING X X X KAH1701AAA HARD TART (CAP / RELAY) X X X X X X X KACY0101AAA CYCLE PROTECTOR X X X X X X X KAF0101AAA UPPORT FEET X X X X X X X KAAC0201PTC TART AIT PTC X X X X X X X KAACH1201AAA CRANKCAE HTR X X X KAACH1401AAA CRANKCAE HTR X X X X KATX0201PUR TXV PURON HO X X X KATX0301PUR TXV PURON HO X X KATX0401PUR TXV PURON HO X KATX0501PUR TXV PURON HO X KAH0601COP OUND HOOD X X X X X X KAH2101COP OUND HOOD X KAALP0301PUR LOW PREURE WITCH X X X X X X X KAAHI0501PUR HIGH PREURE WITCH X X X X X X X KAAL0201LL LIQUID LINE OLENOID X X X X X X X KHA0606MPK* NOW TAND RACK X X X X X X X { Required accessories include ball bearing fan motor, compressor start assist (CAP / Relay), crankcase heater, evaporator freeze stat, hard shut---off TXV. X Available accessory * Available for order through RCD 5

6 ACCEORY UAGE GUIDELINE ACCEORY REQUIRED FOR LOW---AMBIENT COOLING APPLICATION (Below 55 F/12.8_C) REQUIRED FOR LONG LINE APPLICATION* (Over 80 ft./24.38 m) REQUIRED FOR EA COAT APPLICATION (Within 2 miles/3.22 km) Ball Bearing Fan Motor Yes{ No No Compressor tart Assist Capacitor and Relay Yes Yes No Crankcase Heater Yes Yes No Evaporator Freeze Thermostat Yes No No Hard hut --- Off TXV Yes Yes Yes Liquid Line olenoid Valve No No No Motor Master or Low---ambient Pressure witch Yes No No upport Feet Recommended No Recommended Winter tart Control Yes No No * For tubing line sets between 80 and 200 ft. (24.38 and m) and/or 20 ft. (6.09 m) vertical differential, refer to Residential plit--- Longline Application Guideline. { Additional requirement for Low---Ambient Controller (full modulation feature) MotorMasterr Control. Accessory Description and Usage (Listed Alphabetically) 1. Ball-Bearing Fan Motor 5. Cycle Protector A fan motor with ball bearings which permits speed reduction while maintaining bearing lubrication. Required on all units when MotorMasterr 2. Compressor tart Assist - Capacitor and Relay tart capacitor and relay gives a hard boost to compressor motor at each start up. Required for reciprocating compressors in the following applications: Long line Low ambient cooling Hard shut off expansion valve on indoor coil Liquid line solenoid on indoor coil Required for single-phase scroll compressors in the following applications: Long line Low ambient cooling uggested for all compressors in areas with a history of low voltage problems. 3. Compressor tart Assist PTC Type olid state electrical device which gives a soft boost to the compressor at each start -up. uggested in installations with marginal power supply. 4. Crankcase Heater An electric resistance heater which mounts to the base of the compressor to keep the lubricant warm during off cycles. Improves compressor lubrication on restart and minimizes the chance of liquid slugging. Required in low ambient cooling applications. Required in long line applications. uggested in all commercial applications. The cycle protector is designed to prevent compressor short cycling. This control provides an approximate 5 -minute delay after power to the compressor has been interrupted for any reason, including power outage, protector control trip, thermostat jiggling, or normal cycling. 6. Evaporator Freeze Thermostat An PT temperature-actuated switch that stops unit operation when evaporator reaches freeze -up conditions. 7. Liquid -Line olenoid Valve (LL) An electrically operated shutoff valve which stops and starts refrigerant liquid flow in response to compressor operation. It is to be installed at the outdoor unit to control refrigerant off cycle migration in the heating mode. An LL is required in all long line heat pump applications to control refrigerant off cycle migration in the heating mode. ee Long Line Guideline. Required when low ambient kit has been added. 8. Low -Ambient Pressure witch Kit A long life pressure switch which is mounted to outdoor unit service valve. It is designed to cycle the outdoor fan motor in order to maintain head pressure within normal operating limits (approximately 100 psig to 225 psig). The control will maintain working head pressure at low -ambient temperatures down to 0_F when properly installed. A Low -Ambient Pressure witch or MotorMasterr Low -Ambient Controller must be used when cooling operation is used at outdoor temperatures below 55_F (12.8_C). 9. MotorMasterr Low -Ambient Controller A fan -speed control device activated by a temperature sensor, designed to control condenser fan motor speed in response to the saturated, condensing temperature during operation in cooling mode only. For outdoor temperatures down to -20_F (-28.9_C), it maintains condensing temperature at 100_F ±10_F (37.8_C ± _C). A MotorMasterr Low Ambient Controller or Low -Ambient Pressure witch must be used when cooling operation is used at outdoor temperatures below 55_F (12.8_C). uggested for all commercial applications. 6

7 Accessory Description and Usage (Listed Alphabetically) (Continued) 10. Outdoor Air Temperature ensor Designed for use with Carrier Thermostats listed in this publication. This device enables the thermostat to display the outdoor temperature. This device also is required to enable special thermostat features such as auxiliary heat lock out. uggested for all Carrier thermostats listed in this publication. 11. ound Hood Wraparound sound reducing cover for the compressor. Reduces the sound level by about 2 dba. uggested when unit is installed closer than 15 ft (4.6 m) to quiet areas, bedrooms, etc. uggested when unit is installed between two houses less than 10 ft (3.0 m) apart. 12. upport Feet Four stick -on plastic feet that raise the unit 4 in. above the mounting pad. This allows sand, dirt, and other debris to be flushed from the unit base, minimizing corrosion. uggested in the following applications: Coastal installations. Windy areas or where debris is normally circulating. Rooftop installations. For improved sound ratings. 13. Thermostatic Expansion Valve (TXV) A modulating flow -control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving the evaporator. Kit includes valve, adapter tubes, and external equalizer tube. Hard shut off types are available. NOTE: When using a hard shut off TXV with single phase reciprocating compressors, a Compressor tart Assist Capacitor and Relay is required. Required to achieve AHRI ratings in certain equipment 14. Time-Delay Relay An PT delay relay which briefly continues operation of indoor blower motor to provide additional cooling after the compressor cycles off. NOTE: Most indoor unit controls include this feature. For those that do not, use the guideline below. For improved efficiency ratings for certain combinations of indoor and outdoor units. Refer to AHRI Unitary Directory. 15. Winter tart Control This control is designed to alleviate nuisance opening of the low -pressure switch by bypassing it for the first 3 minutes of operation. combinations. Refer to combination ratings. Hard shut off TXV or LL required in air conditioner long line applications. Required for use on all zoning systems. 7

8 ELECTRICAL DATA UNIT IZE --- VOLTAGE, ERIE V/PH OPER VOLT* COMPR FAN MCA MIN WIRE IZE MIN WIRE IZE MAX LENGTH ft. (m) MAX LENGTH ft. (m) MAX MIN LRA RLA FLA 60 C 75 C 60 C 75 C (20.4) 64 (19.5) (13.4) 42 (12.8) (12.8) 40 (12.2) /230/ (17.4) 54 (16.5) (23.2) 73 (22.3) (21.3) 66 (20.1) (27.7) 55 (16.8) 50 * Permissible limits of the voltage range at which the unit will operate satisfactorily { If wire is applied at ambient greater than 30_C, consult table of the NEC (NFPA 70). The ampacity of non ---metallic ---sheathed cable (NM), trade name ROMEX, shall be that of 60_C conditions, per the NEC (NFPA 70) Article If other than uncoated (no---plated), 60 or 75_C insulation, copper wire (solid wire for 10 AWG or smaller, stranded wire for larger than 10 AWG) is used, consult applicable tables of the NEC (NFPA 70). } Length shown is as measured 1 way along wire path between unit and service panel for voltage drop not to exceed 2%. ** Time --- Delay fuse. FLA --- Full Load Amps LRA --- Locked Rotor Amps MCA --- Minimum Circuit Amps RLA --- RatedLoadAmps NOTE: Control circuit is 24---V on all units and requires external power source. Copper wire must be used from service disconnect to unit. All motors/compressors contain internal overload protection. Complies with 2010 requirements of AHRAE tandards 90.1 A-WEIGHTED OUND POWER LEVEL (dba) UNIT IZE --- VOLTAGE, ERIE TANDARD RATING (dba) MAX FUE** or CKT BRK AMP TYPICAL OCTAVE BAND PECTRUM (dba, without tone adjustment) NOTE: Tested in compliance with AHRI but not listed with AHRI. A-WEIGHTED OUND POWER LEVEL (dba) WITH OUND HIELD UNIT IZE --- VOLTAGE, ERIE TANDARD RATING (dba) TYPICAL OCTAVE BAND PECTRUM (dba, without tone adjustment) NOTE: Tested in compliance with AHRI but not listed with AHRI. CHARGING UBCOOLING (TXV-TYPE EXPANION DEVICE) UNIT IZE --- VOLTAGE, ERIE REQUIRED UBCOOLING F ( C) (4.4) (6.1) (5.0) (5.6) (6.1) (6.7) (6.1) 8

9 DIMENION - ENGLIH UNIT ERIE ELECTRICAL CHARACTERITIC A B C D E F G K L M N P OPERATING WEIGHT (lbs) HIPPING WEIGHT (lbs) HIPPING DIMENION (L x W x H) 24ABB318 0 X O O O 25 3/4" 31 13/16" 3 3/4" 5/8" 4 7/16" 21 1/4" 9 1/8" 2 13/16" 1/2" 15 " 12 1/2" 14 3/4" /8" X 30 1/16" X 35 15/16" 24ABB324 0 X O O O 25 3/4" 35 1/4" 3 3/4" 5/8" 4 7/16" 21 1/4" 9 1/8" 2 13/16" 1/2" 13" 14 1/4" 15 7/8" /8" X 30 1/16" X 39 " 24ABB330 0 X O O O 31 3/16" 32 5/16" 3 3/4" 3/4" 6 9/16" 24 11/16" 9 1/8" 2 13/16" 1/2" 16 1/8" 15" 15 7/8" " X 35 1/2" X 35 15/16" 24ABB336 0 X O O O 31 3/16" 39 1/8" 3 3/4" 3/4" 6 9/16" 24 11/16" 9 1/8" 2 13/16" 1/2" 13 5/8" 15 3/4" 18 1/2" " X 35 1/2" X 42 3/4" 24ABB342 0 X O O O 35" 28 15/16" 3 7/8" 7/8" 6 9/16" 28 7/16" 9 1/8" 2 15/16" 5/8" 15 3/4" 15" 12 " /8" X 39 5/16" X 32 9/16" 24ABB348 0 X O O O 35" 32 5/16" 3 7/8" 7/8" 6 9/16" 28 7/16" 9 1/8" 2 15/16" 5/8" 16 1/4" 16 " 14 1/4" /8" X 39 5/16" X 35 15/16" 24ABB360 0, 1 X O O O 35" 28 15/16" 3 7/8" 7/8" 6 9/16" 28 7/16" 9 1/8" 2 15/16" 5/8" 16 " 16 5/8" 12 1/4" /8" X 39 5/16" X 32 9/16" X = YE O = NO / A Q. AIR DICHARGE G M AIR IN AIR DICHARGE B FIELD CONTROL UPPLY CONN. 7/8" HOLE FIELD POWER UPPLY CONN. 7/8" HOLE WITH 1 1/8" KNOCKOUT AIR IN N F " LIQUID LINE CONN. P 3" C 3 1/2" 1 7/8" E D VAPOR LINE CONN. L 5/16" K AIR IN UNIT IZE MINIMUM MOUNTING PAD DIMENION /2" X 23 1/2" 18,24 26" X 26" 30, /2" X 31 1/2" 42,48,60 35" X 35" " TIEDOWN KNOCKOUT (2) PLACE AIR IN 9

10 DIMENION - I UNIT ERIE ELECTRICAL CHARACTERITIC A B C D E F G K L M N P OPERATING WEIGHT (Kgs) HIPPING WEIGHT (Kgs) HIPPING DIMENION (L x W x H) 24ABB318 0 X O O O X X ABB324 0 X O O O X X ABB330 0 X O O O X X ABB336 0 X O O O X X ABB342 0 X O O O X X ABB348 0 X O O O X X ABB360 0, 1 X O O O X X X = YE O = NO / A Q. AIR DICHARGE G M AIR IN AIR DICHARGE B FIELD CONTROL UPPLY CONN HOLE FIELD POWER UPPLY CONN HOLE WITH KNOCKOUT AIR IN N F AIR IN LIQUID LINE CONN P 76.2 C E D VAPOR LINE CONN. L 8.0 K AIR IN UNIT IZE MINIMUM MOUNTING PAD DIMENION X , X , X ,48, X TIEDOWN KNOCKOUT (2) PLACE 10

11 Wall CLEARANCE Wall 6 (152.4) 24 (609.6) ervice 12 (304.8) 24 (609.6) ervice 18 (457.2) Note: Numbers in ( ) = mm 12 (304.8) 18 (457.2) Clearances (various examples) 12 (304.8) Wall 24 (609.6) ervice 18 (457.2) Wall 24 (609.6) ervice 12 (304.8) 24 (609.6) ervice 6 (152.4) A

12 TETED AHRI COMBINATION RATING* NOTE: Ratings contained in this document are subject to change at any time. For AHRI ratings certificates, please refer to the AHRI directory Additional ratings and system combinations can be accessed via the Carrier database at: Equipment performance Calculator can be accessed at: Model Number Indoor Model Furnace Model Capacity EER EER 24ABB318C30 CAP**1814A**+TDR 17, ABB324C30 CAP**2414A**+TDR 22, ABB330C30 CAP**3014A**+TDR 29, ABB336C30 CAP**3617A**+TDR 34, ABB342C30 CAP**4221A**+TDR 40, ABB348C30 CAP**4821A**+TDR 46, ABB360C31 CAP**6024A**+TDR 59, * Ratings are net values reflecting the effects of circulating fan heat. upplemental electric heat is not included. Ratings are based on: EER Energy Efficiency Ratio EER easonal Energy Efficiency Ratio TDR Time---DelayRelay. Inmostcases,only1methodshouldbeusedtoachieve TDR function. Using more than 1 method in a system may cause degradation in performance. Use either the accessory Time---Delay Relay KAATD0101TDR or a furnace equipped with TDR. Most Carrier furnaces are equipped with TDR. NOTE: 1. Ratings are net values reflecting the effects of circulating fan motor heat. upplemental electric heat is not included. 2. Tested outdoor/indoor combinations have been tested in accordance with DOE test procedures for central air conditioners. Ratings for other combinations are determined under DOE computer simulation procedures. 3. Determine actual CFM values obtainable for your system by referring to fan performance data in fan coil or furnace coil literature. 4. Do not apply with capillary tube coils as performance and reliability are significantly affected. 12

13 DETAILED COOLING CAPACITIE# EVAPORATOR AIR CFM EWB F( C) CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens 24ABB318C30 Outdoor ection With CAP**1814A** Indoor ection 72 (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) EVAPORATOR AIR CFM 700 EWB F( C) CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens 24ABB324C30 Outdoor ection With CAP**2414A** Indoor ection 72 (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) ee notes on pg

14 DETAILED COOLING CAPACITIE# (CONT.) EVAPORATOR AIR CFM EWB F( C) CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens 24ABB330C30 Outdoor ection With CAP**3014A** Indoor ection 72 (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) EVAPORATOR AIR CFM 1050 EWB F( C) CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens 24ABB336C30 Outdoor ection With CAP**3617A** Indoor ection 72 (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) ee notes on pg

15 DETAILED COOLING CAPACITIE# (CONT.) EVAPORATOR AIR CFM EWB F( C) CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens 24ABB342C30 Outdoor ection With CAP**4221A** Indoor ection 72 (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) EVAPORATOR AIR CFM 1400 EWB F( C) CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens 24ABB348C30 Outdoor ection With CAP**4821A** Indoor ection 72 (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) ee notes on pg

16 DETAILED COOLING CAPACITIE# (CONT.) EVAPORATOR AIR CFM EWB F( C) CONDENER ENTERING AIR TEMPERATURE F ( C) 75 (23.9) 85 (29.4) 95 (35) 105 (40.6) 115 (46.1) 125 (51.7) Total ens Total ens Total ens Total ens Total ens Total ens 24ABB360C31 Outdoor ection With CAP**6024A** Indoor ection 72 (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) (22.2) (19.4) (16.7) (13.9) { Total and sensible capacities are net capacities. Blower motor heat has been subtracted. } ensible capacities shown are based on 80_F (27_C) entering air at the indoor coil. For sensible capacities at other than 80_F (27_C), deduct 835 Btuh (245 kw) per 1000 CFM (480 L/) of indoor coil air for each degree below 80_F (27_C), or add 835 Btuh (245 kw) per 1000 CFM (480 L/) of indoor coil air per degree above 80_F (27_C). # Detailed cooling capacities are based on indoor and outdoor unit at the same elevation per AHRI standard 210/ If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. ** kw is total of indoor and outdoor unit kilowatts. {{ At TVA rating indoor condition (75_F edb/63_f ewb). All other indoor air temperatures are at 80_F edb. NOTE: When the required data falls between the published data, interpolation may be performed. Extrapolation is not an acceptable practice. EWB Entering Wet Bulb NOTE: When the required data fall between the published data, interpolation may be performed. Extrapolation is not an acceptable practice. 16

17 CONDENER ONLY RATING* T F( C) 30 ( ) 35 (1.67) 40 (4.44) 45 (7.22) 50 (10.0) 55 (12.78) 30 ( ) 35 (1.67) 40 (4.44) 45 (7.22) 50 (10.0) 55 (12.78) 30 ( ) 35 (1.67) 40 (4.44) 45 (7.22) 50 (10.0) 55 (12.78) 30 ( ) 35 (1.67) 40 (4.44) 45 (7.22) 50 (10.0) 55 (12.78) ee notes on pg. 18 CONDENER ENTERING AIR TEMPERATURE F ( C) 55 (12.78) 65 (18.33) 75 (23.89) 85 (29.44) 95 (35.0) 105 (40.56) 115 (46.11) 125 (51.67) 24ABB318C30 TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW ABB324C30 TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW ABB330C30 TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW ABB336C30 TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW

18 CONDENER ONLY RATING* (CONT.) T F( C) 30 ( ) 35 (1.67) 40 (4.44) 45 (7.22) 50 (10.0) 55 (12.78) 30 ( ) 35 (1.67) 40 (4.44) 45 (7.22) 50 (10.0) 55 (12.78) 30 ( ) 35 (1.67) 40 (4.44) 45 (7.22) 50 (10.0) 55 (12.78) CONDENER ENTERING AIR TEMPERATURE F ( C) 55 (12.78) 65 (18.33) 75 (23.89) 85 (29.44) 95 (35.0) 105 (40.56) 115 (46.11) 125 (51.67) 24ABB342C30 TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW ABB348C30 TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW ABB360C31 TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW TCG DT KW * AHRI listing applies only to systems shown in Combination Ratings table. KW --- Outdoor Unit Kilowatts Only. DT --- aturated Temperature Leaving Compressor ( F/ C) T --- aturated Temperature Entering Compressor ( F/ C) TCG --- Gross Cooling Capacity (1000 Btuh) 18

19 GUIDE PECIFICATION GENERAL Description Outdoor-mounted, air-cooled, split-system air conditioner unit suitable for ground or rooftop installation. Unit consists of a hermetic compressor, an air-cooled coil, propeller-type condenser fan, and a control box. Unit will discharge supply air upward as shown on contract drawings. Unit will be used in a refrigeration circuit to match up to a packaged fan coil or coil unit. Quality Assurance Unit will be rated in accordance with the latest edition of AHRI tandard 210. Unit will be certified for capacity and efficiency, and listed in the latest AHRI directory. Unit construction will comply with latest edition of ANI/ AHRAE and with NEC. Unit will be constructed in accordance with UL standards and will carry the UL label of approval. Unit will have c-ul approval. Unit cabinet will be capable of withstanding Federal Test Method tandard No. 141 (Method 6061) 500 -hr salt spray test. Air-cooled condenser coils will be leak tested at 150 psig and pressure tested at 450 psig. Unit constructed in IO9001 approved facility. Delivery, torage, and Handling Unit will be shipped as single package only and is stored and handled per unit manufacturer s recommendations. Warranty (for inclusion by specifying engineer) U.. and Canada only. PRODUCT Equipment Factory assembled, single piece, air -cooled air conditioner unit. Contained within the unit enclosure is all factory wiring, piping, controls, compressor, refrigerant charge r (R -410A), and special features required prior to field start -up. Unit Cabinet Unit cabinet will be constructed of galvanized steel, bonderized, and coated with a powder coat paint. AIR -COOLED, PLIT -YTEM AIR CONDITIONER 1-1/2 TO 5 NOMINAL TON Fans Condenser fan will be direct-drive propeller type, discharging air upward. Condenser fan motors will be totally enclosed, 1 -phase type with class B insulation and permanently lubricated bearings. hafts will be corrosion resistant. Fan blades will be statically and dynamically balanced. Condenser fan openings will be equipped with coated steel wire safety guards. Compressor Compressor will be hermetically sealed. Compressor will be mounted on rubber vibration isolators. Condenser Coil Condenser coil will be air cooled. Coil will be constructed of aluminum fins mechanically bonded to copper tubes which are then cleaned, dehydrated, and sealed. ArmorPlate coating - Aluminum fin material is pre-coated on both sides with a corrosion protective epoxy phenolic coating. Refrigeration Components Refrigeration circuit components will include liquid -line shutoff valve with sweat connections, vapor-line shutoff valve with sweat connections, system charge of r (R -410A) refrigerant, and compressor oil. Unit will be equipped with filter drier for refrigerant. Operating Characteristics The capacity of the unit will meet or exceed Btuh at a suction temperature of F/_C. The power consumption at full load will not exceed kw. Combination of the unit and the evaporator or fan coil unit will have a total net cooling capacity of Btuh or greater at conditions of CFM entering air temperature at the evaporator at F/_C wet bulb and F/_C dry bulb, and air entering the unit at F/_C. The system will have a EER of Btuh/watt or greater at DOE conditions. Electrical Requirements Nominal unit electrical characteristics will be v, single phase, 60 hz. The unit will be capable of satisfactory operation within voltage limits of v to v. Unit electrical power will be single point connection. Control circuit will be 24v. pecial Features Refer to section of this literature identifying accessories and descriptions for specific features and available enhancements. 19