Product Data. 38YCC (60 Hz) 10 SEER Heat Pump Export Model Sizes ( /2 to 5 Nominal Tons) FEATURES AND BENEFITS.

Transcription

1 (60 Hz) 10 SEER Heat Pump Export Model Sizes ( /2 to 5 Nominal Tons) Product Data The Outdoor Section of Split-System Heat Pumps is designed for quiet, reliable heating during the winter and cooling during the summer. With EER ratings up to 9.5, this heat pump system provides economy of operation through energy conservation when used with components designated by the manufacturer. The recovers heat for indoor comfort from outdoor air during the heating season and, by automatically reversing the refrigerant system, removes indoor heat and excess humidity during the cooling season. All models are listed with UL (U.S. and Canada). FEATURES AND BENEFITS Electrical Range All units are offered in 208/230v single phase. Three-phase units are available from 036 through 060 sizes in 208/230v. Wide Range of Sizes All sizes of the are offered in single phase v. The 030 through 060 models are offered in 208/230v 3 phase. Unit Design All units are equipped with totally enclosed fan motors for greater reliability under adverse weather conditions. The large, wrap -around coil uses copper tube epoxy coated enhanced aluminum fin and is designed for optimum heat transfer and corrosion protection during heating and cooling. The vertical air discharge carries the sound and air up and away from adjacent patio areas and foliage. Coil can be cleaned with a common garden hose. WeatherArmort Cabinet A weather protective cabinet of pre -painted steel is protected underneath by a zinc galvanized coating for a finish that will last for many years. All screws on cabinet exterior are coated for a long -lasting, rust -resistant, quality appearance. Compressor Designed specifically for heat pump duty, with energy efficiency during heating and cooling operation. Each compressor is hermetically sealed against contamination to assure long life and dependable performance; compressors are also externally mounted on rubber isolators for quiet operation. For improved serviceability, all models are equipped with a compressor terminal plug. Continuous compressor operation is approved down to -30_F (-34.4_C) in the heating mode, and down to 55_F (12.8_C) in the cooling mode (unless equipped for low -ambient operation). Compressor Protection Each compressor is protected with internal temperature - and current -sensitive overloads. Reliable standard components Includes a suction -tube accumulator that reduces the amount of liquid refrigerant that reaches the compressor; a lowpressure switch to stop the compressor if refrigerant charge is lost; a crankcase heater on all 3 -phase units (except 030 size) to keep compressor oil warm and free of refrigerant for maximum lubricity; an internal compressor relief valve for high -pressure protection. 3-phase monitor board (scroll compressor models) Control board that monitors the electrical phase and prevents compressor operation if wired incorrectly.

2 FEATURES AND BENEFITS (CONT.) External Service Valves Service valves are brass, front seating type. The has sweat field connections. Valves are externally located so refrigerant tube connections can be made quickly and easily. Each valve has a service port for ease of checking operating refrigerant pressures. Easy Serviceability One panel provides access to electrical controls. Removal of wire dome gives access to fan motor and removal of the top gives access to the coil and compressor. All models are equipped with a compressor terminal plug. Discharge Muffler Minimizes low frequency sound and pressure pulsation generated by compressor discharge gas. Defrost Control Board Incorporates a defrost relay, defrost timer, and low -voltage terminations. The defrost control is a time and temperature initiation/termination control which includes 3 field -selectable time periods of 30, 60, and 90 minutes. PRODUCT NUMBER NOMENCLATURE 018 X 3 A A 10 SEER Electric Heat Pump Nominal /2 Ton Tons /2 Tons Tons /2 Tons Ton Ton Series Packaging X =Export =Standard Electrical Supply 3=208/ =208/ ISO 9001:2000 REGISTERED PHYSICAL DATA UNIT SIZE A A A, 5A A,5A B,5A B,5A A,5A OPERATING WEIGHT (lb/kg) 127/ / / / / / /107.5 COMPRESSOR TYPE Recip Scroll Recip Scroll REFRIGERANT R Control Piston Charge Ft./4.6m 4.25/ / / / / / /4.8 COND FAN Propeller Type, Direct Drive Air Discharge Vertical Air Qty (CFM/L/S) 1700/ / / /1557 Motor HP 1/12 1/4 Motor RPM COND COIL Copper Tube, Aluminum Plate Fin Face Area sq ft / sq m 9.11/ / / / /2.08 Fins per in./25.4 mm Rows 1 Circuits VALVE CONNECTION Sweat Vapor (in./mm)ld 5/8/ /4/ /8/22.23 Liquid (in./mm)ld 3/8/9.53 REFRIG. TUBES*(in./mm) OD Vapor ( ft/ m Tube) 5/8/ /4/ /8/22.3 Vapor (Max Diameter for Long Line Applications) 3/4/ /8/ /8/28.58 Liquid ( ft./ m/ Tube Length) 3/8/9.53 Liquid (For Long Line Applications) 3/8/9.53 * For tubing sets between 50 and 175 ft (15.24 and m) horizontal and/or 20 ft (6.1 m) vertical differential, consult Residential Split Systems Long --- Line Application Guideline. NOTE: See unit Installation Instructions for proper installation. 2

3 ELECTRICAL DATA UNIT SIZE V/PH OPER VOLTS* COMPRESSOR Max Min LRA RLA FAN FLA MCA 60 C MIN WIRE SIZE 75 C MIN WIRE SIZE 60 C MAX LENGTH ft (m) 75 C MAX LENGTH ft (m) MAX FUSE** OR CKT BKR AMPS A A A A / B B A A A A 208/230/ A A * Permissible limits of the voltage range at which unit will operate satisfactorily. Operation outside these limits may result in unit failure. { If wire is applied at ambient greater than 30 C, consult Table of the NEC (ANSI/NFPA 70). The ampacity of nonmetallic---sheathed cable (NM), trade name ROMEX, shall be that of 60 C conductors, per the NEC (ANSI/NFPA 70) Article If other than uncoated (non---plated), 60 or 75 C insulation, copper wire (solid wire for 10 AWG and smaller, stranded wire for larger than 10 AWG) is used, consult applicable tables of the NEC (ANSI/NFPA 70). } Length shown is as measured 1 way along wire path between the unit and service panel for a voltage drop not to exceed 2%. ** Time --- delay fuse. FLA --- Full Load Amps LRA --- Locked Rotor Amps MCA --- Minimum Circuit Amps RLA --- RatedLoadAmps NOTES: 1. Control circuit is 24v on all units and requires external power source. 2. Copper wire must be used from service disconnect to unit. 3. All motors/compressors contain internal overload protection. METERING DEVICE UNIT SIZE --- VOLTAGE, SERIES OUTDOOR PISTON PISTON* REQUIRED SUB---COOLING _F (_C) A (6.7) A (6.7) A, 5A (6.7) A, 5A (7.8) B, 5A (8.9) B, 5A (8.3) A, 5A (5.6) * Piston listed is for any approved non ---capillary tube coil combination. Piston is shipped with outdoor unit and must be installed in an approved indoor coil. A -WEIGHTED SOUND POWER (dba) UNIT SIZE STANDARD TYPICAL OCTAVE BAND SPECTRUM (db, without tone adjustment) RATING (db) A A A,5A A,5A B,5A B,5A A,5A

4 ACCESSORIES ORDERING NUMBER DESCRIPTION KAATD0101TDR Time--Delay Relay All Sizes KSALA0201R22 Low--Ambient Pressure Switch All sizes KSALA0401AAA*{ MotorMaster Low--Ambient Controller Sizes ; 036 (3A, 5A); 042 (3B, 5A); 048 (3B, 5A); 060 (3A, 5A) HC34GE232 (RCD) Ball Bearing Fan Motor Sizes 018, 024 HC40GE232 (RCD) Ball Bearing Fan Motor Sizes 030 (3A, 5A); 036 (3A, 5A); 042 (3B, 5A); 048 (3B, 5A); 060 (3A, 5A) KAAFT0101AAA} Evaporator Freeze Thermostat All Sizes KH0101AAA} Isolation Relay All Sizes KSACY0101AAA Cycle Protector All Sizes KSAHS0901AAA Start Assist Capacitor and Relay Size 030 (3A) KSAHS2101AAA Start Assist Capacitor and Relay Sizes 024 (3A); 036 (3A) KSAHS2001AAA Start Assist Capacitor and Relay Size 018 (3A) KSAHS1501AAA Start Assist Capacitor and Relay Sizes 042 (3B); 048 (3B) KSAHS1601AAA Start Assist Capacitor and Relay Size 060 (3A) KAACS0201PTC Start Assist PTC Sizes (3A); 036 (3A); 042 (3B); 048 (3B); 060 (3A) Standard Crankcase Heater All Three Phase KAACH1001AAA Crankcase Heater (3A) KAACH1201AAA Crankcase Heater Sizes 042 (3B); 048 (3B); 060 (3A) KSASH0601COP Sound Hood Size 042 (3B, 5A) KSASH2001BRL Sound Hood Sizes (3A) KSASH2101COP Sound Hood Sizes 048 (3B, 5A); 060 (3A, 5A) KHAOT0301FST Outdoor Thermostat All Sizes KHAOT0201SEC Secondary Outdoor Thermostat All Sizes KSATX0601HSO** TXV (Hard Shutoff) Sizes KSATX0701HSO** TXV (Hard Shutoff) Size 048 KSATX1001HSO** TXV (Hard Shutoff) Size 060 KHATX0201RPB TXV (RPB) Size 018 KHATX0301RPB TXV (RPB) Size 024 KHATX0401RPB TXV (RPB) Size 030 KHATX0501RPB TXV (RPB) Sizes 036, 042 KHATX0601RPB TXV (RPB) Sizes 048 KHATX0701RPB TXV (RPB) Sizes 060 KHAHI0101HPS High--Pressure Switch All Sizes P S (RCD) Filter Drier Bi--Flow Sizes P S (RCD) Filter Drier Bi--Flow Sizes KHALS0401LLS Liquid--Line Solenoid Valve (LSV) All Sizes KAACF1001MED Coastal Filter Kit KAACF1101LRG Coastal Filter Kit * Isolation relay required. { Fan motor with ball bearings required. } Use with low---ambient controller. ** Addition of these accessories requires capacitor and relay compressor start assist on all single---phase reciprocating compressor applications. ACCESSORY THERMOSTATS THERMOSTAT / SUBBASE PKG. TSTATCCPRH01---B* TSTATCCPHH01---B* TSTATCCPHP01---B TSTATCCNHP01---C TSTATCCSHP01 TSTATCCBHP01* ---B TSTATXXSEN01---B** TSTATXXNBP01 TSTATXXPBP01 TSTATXXSBP01 TSTATXXBBP01 TSTATXXCNV10{ TB --- PHP DESCRIPTION Thermidistatt Control Non---Programmable/Programmable Thermostat with Humidity Control (For use in Dual Fuel, AC, HP, and 2S applications. Includes Outdoor Air Temperature Sensor.) HybridHeatt (Dual Fuel) Thermostat Auto Changeover, 7---Day Programmable, F/ C, Includes Outdoor Sensor (TSTATXXSEN01---B) Thermostat Auto Changeover, 7---Day Programmable, F/ C, 2 ---Stage Heat, 1 ---Stage Cool Thermostat Auto Changeover, Non---Programmable, F/ C, 2 ---Stage Heat, 1 ---Stage Cool Standard Programmable Thermostat Manual Changeover, Day Programmable, F/ C, 1 ---Stage Heat/ 1 ---Stage Cool Builder s Thermostat Heat Pump, Non---Programmable, F/ C, 2---Stage Heat, 1---Stage Cool, Manual Changeover Outdoor Air Temperature Sensor Backplate for Non---Programmable Thermostat Backplate for Programmable Thermostat and Thermidistatt Control Backplate for Standard Programmable Thermostat Backplate for Builder s Thermostat Thermostat Conversion Kit (4 to 5 Wire) 10 Pack Base Series Programmable HP Stat TB --- NHP Base Series Non---programmable HP Stat * Do not use in zoning heat pump applications. ** Outdoor temperature sensor is an accessory for all Carrier electronic thermostats, except the non---programmable air conditioner version and builder;s thermostats. It allows the temperature at a remote location (outdoors) to be displayed on the thermostat. The outdoor air temperature sensor must be used with the HybridHeatt (dual fuel) thermostat. { Thermostat conversion kit is a 24---vac accessory that can turn a 4---wire thermostat application into a 5---wire application. This kit can also be used to re place a broken thermostat wire, or add an extra wire when needed. The outdoor air temperature sensor is included with the Thermidistat Control and HybridHeatt (dual fuel) thermostat. 4

5 ACCESSORY USAGE GUIDELINE ACCESSORY REQUIRED FOR LOW---AMBIENT APPLICATIONS (Below 55 F / C) REQUIRED FOR LONG LINE APPLICATIONS* (Over 80 Ft. / m) REQUIRED FOR SEA COAST APPLICATIONS (Within 2 miles / 3.22 km) Accumulator No No No Ball Bearing Fan Motor Yes{ No No Compressor Start Assist Capacitor and Relay Yes{ Yes No Crankcase Heater Yes{ Yes No Evaporator Freeze Thermostat Yes{ No No Isolation Relay Yes{ No No Liquid Line Solenoid Valve No See Long Line Application Guideline No Motor Master Control or Low---ambient Pressure Switch Yes{ No No Support Feet Recommended No Recommended * For tubing line sets between 80 and 200 ft. (24.38 and m) and/or 20 ft. vertical (6.09 m) differential, refer to Residential Split System Long Line Application Guideline. { Required for Low---Ambient Controller MotorMasterr Control only. Accessory Description and Usage (Listed Alphabetically) 1. Ball-Bearing Fan Motor A fan motor with ball bearings which permits speed reduction while maintaining bearing lubrication. Required on all units when MotorMasterr is used. 2. Compressor Start Assist - Capacitor and Relay Start capacitor and relay gives a hard boost to compressor motor at each start up. Required for reciprocating compressors in the following applications: Long line Low ambient cooling Hard shut off expansion valve on indoor coil Liquid line solenoid on indoor coil Required for single-phase scroll compressors in the following applications: Long line Low ambient cooling Suggested for all compressors in areas with a history of low voltage problems. 3. Compressor Start Assist PTC Type Solid state electrical device which gives a soft boost to the compressor at each start -up. Suggested in installations with marginal power supply. 4. Crankcase Heater An electric resistance heater which mounts to the base of the compressor to keep the lubricant warm during off cycles. Improves compressor lubrication on restart and minimizes the chance of liquid slugging. Required in low ambient cooling applications. Required in long line applications. Suggested in all commercial applications. 5. Cycle Protector The cycle protector is designed to prevent compressor short cycling. This control provides an approximate 5 -minute delay after power to the compressor has been interrupted for any reason, including power outage, protector control trip, thermostat jiggling, or normal cycling. 6. Evaporator Freeze Thermostat An SPST temperature-actuated switch that stops unit operation when evaporator reaches freeze -up conditions. Required when low ambient kit has been added. 7. High Pressure Switch A high pressure switch that protects unit against excessive pressure. Required in all heat pumps operated in dual fuel applications. 8. Isolation Relay An SPDT relay which switches the low -ambient controller out of the outdoor fan motor circuit when the heat pump switches to heating mode. Required in all heat pumps where low ambient kit has been added. 9. Liquid -Line Solenoid Valve (LLS) An electrically operated shutoff valve which stops and starts refrigerant liquid flow in response to compressor operation. It is to be installed at the outdoor unit to control refrigerant off cycle migration in the heating mode. An LLS is required in all long line heat pump applications to control refrigerant off cycle migration in the heating mode. See Long Line Guideline. 10. Low -Ambient Pressure Switch Kit A long life pressure switch which is mounted to outdoor unit service valve. It is designed to cycle the outdoor fan motor in order to maintain head pressure within normal operating limits (approximately 100 psig to 225 psig). The control will maintain working head pressure at low -ambient temperatures down to 0_F when properly installed. A Low -Ambient Pressure Switch or MotorMasterr Low -Ambient Controller must be used when cooling operation is used at outdoor temperatures below 55_F (12.8_C). 5

6 Accessory Description and Usage (Listed Alphabetically) - CONTINUED 11. MotorMasterr Low -Ambient Controller A fan -speed control device activated by a temperature sensor, designed to control condenser fan motor speed in response to the saturated, condensing temperature during operation in cooling mode only. For outdoor temperatures down to -20_F (-28.9_C), it maintains condensing temperature at 100_F ±10_F (37.8_C ± 5.5_C). A MotorMasterr Low Ambient Controller or Low -Ambient Pressure Switch must be used when cooling operation is used at outdoor temperatures below 55_F (12.8_C). Suggested for all commercial applications. 12. Outdoor Air Temperature Sensor Designed for use with Carrier Thermostats listed in this publication. This device enables the thermostat to display the outdoor temperature. This device also is required to enable special thermostat features such as auxiliary heat lock out. Suggested for all Carrier thermostats listed in this publication. 13. Outdoor Thermostat An SPDT temperature -actuated switch which turns on supplemental electric heaters when outdoor air temperature drops below a user-selected set point. Electric supplemental heat applications in non -variable speed indoor units when electric heat staging is desired. Some local codes may require limiting the heating head pressure in the vapor line in some applications. 14. Secondary Outdoor Thermostat An SPDT temperature -actuated switch which turns on third -stage of supplemental electric heaters when outdoor air temperature drops below the second -stage set point. Outdoor thermostat applications where electric heater is capable of 3 -stage operation. 15. Snow Stand Coated wire rack which supports unit 18 in. (457.2 mm) above mounting pad to allow for drainage from unit base. Suggested in the following applications: Heat pump installations in heavy snowfall areas. Heat pump installations in snow drift locations. Heat pump installations in areas of prolonged subfreezing temperatures. All commercial installations. 16. Sound Hood Wraparound sound reducing cover for the compressor. Reduces the sound level up to 2 dba. Suggested when unit is installed closer than 15 ft (4.57 m) to quiet areas, bedrooms, etc. Suggested when unit is installed between two houses less than 10 ft (3.05 m) apart. Suggested in the following applications: Heat pump installations in heavy snowfall areas. Heat pump installations in snowdrift locations. Heat pump installations in areas of prolonged subfreezing temperatures. All commercial installations. 17. Thermostatic Expansion Valve (TXV) Bi-Flow A modulating flow -control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving the evaporator. Required in all heat pump applications 18. Time-Delay Relay An SPST delay relay which briefly continues operation of indoor blower motor to provide additional cooling after the compressor cycles off. Note: Most indoor unit controls include this feature. For those that do not, use the guideline below. Accessory required to meet ARI rating, where indoor not equipped. 6

7 DIMENSIONS (ENGLISH) 7

8 DIMENSIONS (S.I.) 8

9 BALANCE POINT WORKSHEET (ENGLISH) B,5A B,5A 9 OUTDOOR TEMPERATURE, _F

10 BALANCE POINT WORKSHEET (S.I.) A,5A FA4CNF(F,C) B,5A FA4CN(F,C) B,5A FA4CN(F,C) A,5A FA4CN(F,C) A,5A FA4CN(F,C) BUILDING HEAT LOSS, KW UNIT INTEGRATED HEATING CAPACITY, KW A FA4CN(F,C) A FA4CN(F,C)018 5 BASED ON ENT. AT 21ºC ANDATRATEDCFM OUTDOOR TEMPERATURE, _C

11 COMBINATION RATINGS* OUTDOOR UNIT SIZE --- SERIES UNIT NOMINAL --- FLOW CFM L/S Rated BTUH 95 F (35 C) kw kw Rated EER Heating High F (8 C) Low F ( C) Rated BTUH kw kw Rated BTUH kw FB4BN(F,L) A FA4CN(F,C) FA4CN(F,C) FB4BN(F,L) A FA4CN(F,C) FA4CN(F,C) FB4BN(F,L) A,5A FA4CN(F,C) FA4CN(F,C) FB4BN(F,L) A,5A FA4CN(F,C) FA4CN(F,C) FB4BN(F,L) B,5A FA4CN(F,C) FA4CN(F,C) FB4BN(F,L) B,5A FB4BN(F,L) FA4CN(F,C) FA4CN(F,C) A,5A FB4BN(F,L) FA4CN(F,C) * Ratings are net values reflecting the effects of circulating fan heat. Supplemental electric heat is not included. Ratings are based on: Cooling Standard: 80_F (27_C) db 67_F (19_C) wb indoor entering air temperature and 95_F (35_C) db air entering outdoor unit. High---Temp Heating Standard: 70_F (21_C) db indoor entering air temperature and 47_F (8_C) db 43 F (6_C) wb air entering outdoor unit. Low---Temp Heating Standard: 70_F (21_C) db indoor entering air temperature and 17_F (±9_C) db 15 F (±10_C) wb air entering outdoor unit. SEER Seasonal Energy Efficiency Ratio COP Coefficient of Performance TDR Time ---Delay Relay HSPF Heating Seasonal Performance Factor EER Energy Efficiency Ratio kw 38CKC 11

12 DETAILED COOLING CAPACITIES* (ENGLISH) COIL CFM EWB [ CONDENSER ENTERING TEMPERATURES F [ [ [ Sens] Sens] Sens] Sens] Sens] Sens] A Outdoor Section With FA4CN(F,C)018 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) [ [ COIL CFM EWB [ CONDENSER ENTERING TEMPERATURES F [ [ [ [ [ Sens] Sens] Sens] Sens] Sens] Sens] A Outdoor Section With FA4CN(F,C)024 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) See notes on page 13 12

13 DETAILED COOLING CAPACITIES* (ENGLISH) CONTINUED COIL CONDENSER ENTERING TEMPERATURES F CFM EWB Sens Sens Sens Sens Sens Sens A Outdoor Section With FA4CN(F,C)030 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) COIL CFM EWB [ Sens ] CONDENSER ENTERING TEMPERATURES F [ [ [ [ [ Sens] Sens] Sens] Sens] Sens] A, 5A Outdoor Section With FA4CN(F,C)036 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) See notes on page 13 13

14 DETAILED COOLING CAPACITIES* (ENGLISH) CONTINUED COIL CFM EWB [ CONDENSER ENTERING TEMPERATURES F [ [ [ [ [ Sens] Sens] Sens] Sens] Sens] Sens] B, 5A Outdoor Section With FA4CN(F,C)042 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) COIL CFM EWB [ CONDENSER ENTERING TEMPERATURES F [ [ [ [ [ Sens] Sens] Sens] Sens] Sens] Sens] B, 5A Outdoor Section With FA4CN(F,C)048 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) FB4BN(F,L) See notes on page

15 DETAILED COOLING CAPACITIES* (ENGLISH) CONTINUED COIL CFM EWB [ CONDENSER ENTERING TEMPERATURES F [ [ [ [ [ Sens] Sens] Sens] Sens] Sens] Sens] A, 5A Outdoor Section With FA4CN(F,C)060 Indoor Section Cooling Indoor Model *FB4BN(F,L) NOTE: When the required data fall between the published data, interpolation may be performed. Extrapolation is not an acceptable practice. * Detailed cooling capacities are based on indoor and outdoor unit at the same elevation per ARI standard 210/ If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. { and sensible capacities are net capacities. Blower motor heat has been subtracted. } Sensible capacities shown are based on 80 F (27 C) entering air at the indoor coil. For sensible capacities at other than 80 F (27 C), deduct 835 Btuh (245 kw) per 1000 CFM (480 L/S) of indoor coil air for each degree below 80 F (27 C), or add 835 Btuh (245 kw) per 1000 CFM (480 L/S) of indoor coil air per degree above 80 F (27 C). ** Unit kw is total of indoor and outdoor unit kilowatts. EWB --- Entering Wet Bulb 15

16 DETAILED COOLING CAPACITIES* (S.I.) COIL CONDENSER ENTERING TEMPERATURES C CFM EWB Sens Sens Sens Sens Sens Sens A Outdoor Section With FA4CN(F,C)018 Indoor Sectione Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) COIL CONDENSER ENTERING TEMPERATURES C CFM EWB Sens Sens Sens Sens Sens Sens A Outdoor Section With FA4CN(F,C)024 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) See notes on page 17 16

17 DETAILED COOLING CAPACITIES* (S.I.) CONTINUED COIL CONDENSER ENTERING TEMPERATURES C CFM EWB Sens Sens Sens Sens Sens Sens A Outdoor Section With FA4CN(F,C)030 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) COIL CONDENSER ENTERING TEMPERATURES C CFM EWB Sens Sens Sens Sens Sens Sens A, 5A Outdoor Section With FA4CN(F,C)036 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) See notes on page 17 17

18 DETAILED COOLING CAPACITIES* (S.I.) CONTINUED COIL CONDENSER ENTERING TEMPERATURES C CFM EWB Sens Sens Sens Sens Sens Sens B, 5A Outdoor Section With FA4CN(F,C)042 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) COIL CONDENSER ENTERING TEMPERATURES C CFM EWB Sens Sens Sens Sens Sens Sens B, 5A Outdoor Section With FA4CN(F,C)048 Indoor Section Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) FB4BN(F,L) See notes on page 17 18

19 DETAILED COOLING CAPACITIES* (S.I.) CONTINUED COIL CONDENSER ENTERING TEMPERATURES C CFM EWB Sens Sens Sens Sens Sens Sens A, 5A Outdoor Section With FA4CN(F,C)060 Indoor Section Cooling Indoor Model *FB4BN(F,L) NOTE: When the required data fall between the published data, interpolation may be performed. Extrapolation is not an acceptable practice. * Detailed cooling capacities are based on indoor and outdoor unit at the same elevation per ARI standard 210/ If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. { and sensible capacities are net capacities. Blower motor heat has been subtracted. } Sensible capacities shown are based on 80 F (27 C) entering air at the indoor coil. For sensible capacities at other than 80 F (27 C), deduct 835 Btuh (245 kw) per 1000 CFM (480 L/S) of indoor coil air for each degree below 80 F (27 C), or add 835 Btuh (245 kw) per 1000 CFM (480 L/S) of indoor coil air per degree above 80 F (27 C). ** Unit kw is total of indoor and outdoor unit kilowatts. EWB --- Entering Wet Bulb 19

20 HEAT PUMP HEATING PERFORMANCE (ENGLISH) OUTDOOR COIL ENTERING TEMPERATURES F EDB CFM kw kw kw kw kw A Outdoor Section With FA4CN(F,C)018 Indoor Section Pow er kw Pow er kw Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) Pow er kw EDB CFM OUTDOOR COIL ENTERING TEMPERATURES F kw kw kw kw kw A Outdoor Section With FA4CN(F,C)024 Indoor Section kw kw Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) kw See notes on page 23 20

21 HEAT PUMP HEATING PERFORMANCE (ENGLISH) CONTINUED OUTDOOR COIL ENTERING TEMPERATURES F EDB CFM kw kw kw kw A Outdoor Section With FA4CN(F,C)030 Indoor Section kw kw kw Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) kw EDB CFM OUTDOOR COIL ENTERING TEMPERATURES F kw kw kw kw A, 5A Outdoor Section With FA4CN(F,C)036 Indoor Section kw kw kw Cooling Indoor Model *FA4CN(F,C) FB4BN(F,L) kw See notes on page 23 21