Models C708 & C716 McDonald's Heat Treatment Soft Serve Freezers

Transcription

1 Models C708 & C716 McDonald's Heat Treatment Soft Serve Freezers Model C708 Model C716 Insert for C708/C716 Operator Manual MCD 11/26/13 (Rev. G)

2

3 Notes: 1

4 The McDonald's C708 and C716 are similar to the standard Models C708 and C716. Follow the instructions in the C708/C716 Operator's Manual and use this insert to substitute the following information where applicable. PARTS IDENTIFICATION/FUNCTIONS Replace the Accessories Parts Identification/Function information with the following: C708 Accessories (See Figure 1.) ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR. CLASS Pail-Mix 10 Qt. 1 Holds solution for cleaning and 000 sanitizing the freezer WHT Tool-O-Ring Removal 1 Provides easy removal of o-rings Tool-Shaft-Drive-Pump Hopper Lubricant-Taylor Hi-Performance 5 X59380 Dispenser A.-Cup & Cone 1 Enables easy removal of the pump drive shaft Lubricant for moving parts and 000 wear items. 1 Dispenses cups and cones. 103 * X Kit A.-Tool Box C708 1 Contains: 1/X63146 tune up kit, 1/X53795 topping pump spares kit, 1/ ladle, 1/ Taylor Lube HP, 1/ drive shaft tool, 1/ drive shaft tool, 1/ tool box. * X Kit A.-Syrup Rail-Side Mount * X59454 Kit A.-Syrup Rail C708 Front (B.O.M. C70833AFG only) 1 Contains: 1/X rail assy., 1/X53800-BRN pump, 1/ ladle, 1/ syrup jar, 1/ syrup jar, 1/ jar lid, 1/ drip tray, 1/ drip tray shelf. 1 1/X48147 bracket, 1/X59398 rail assy., 2/ screw, 2/ collar, 1/ corner, 3/ jar, 2/ shield, 2/ tray, 1/ BRN pump, 1/ RED pump, 1/ TAN pump. * X57797 Kit A.-Parts Tray 1 Contains 1/ barrel and 1/ simplified pump plastic parts trays, which are used for air drying parts when cleaning the machine. * X44127 Brush A.-Package HT 1 Contains 1/each of , , , , , , , , brushes required for cleaning. (Note: See illustration in C708/C716 Operator Manual.) * Not Shown

5 C708 Accessories Figure

6 C716 Accessories (See Figure 2.) ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR. CLASS Pail-Mix 10 Qt. 1 Holds solution for cleaning and 000 sanitizing the freezer WHT Tool-O-Ring Removal 1 Provides easy removal of o-rings Tool-Shaft-Drive-Pump Hopper Lubricant-Taylor Hi-Performance 1 Enables easy removal of the pump drive shaft. 1 Lubricant for moving parts and wear items. 5 X42811 Holder A.-Lid 1 Holds the sundae cup lids. 103 Contains: 1/ magnetic strip, 1/ front lid holder, 1/ panel lid holder. 6 X63388 Dispenser A.-Cup & 1 Dispenses cups and cones. 103 Cone * X Kit A.-Tool Box C716 1 Contains: 1/X tune up kit, 1/X53795 topping pump 000 spares kit, 2/ ladles, 1/ Taylor Lube HP, 1/ drive shaft tool, 1/ tool box. * X67432 Kit A.-Parts Tray 1 Contains barrel and simplified pump plastic parts trays, which are used for air drying parts when cleaning the machine. 000 * X56533 Kit A.-Power Cord Hanger 1 Used to hold the power cord off the floor. Contains: 2/ washer, 1/ hanger, 1/ nipple, 1/ nut, 1/ connector, 1/ nut. * X44127 Brush A.-Package HT 1 Contains 1/each of , , , , , , , , brushes required for cleaning. (Note: See illustration in C708/C716 Operator Manual.) * Not Shown

7 C716 Accessories Figure

8 Add the following X53800-BRN/TAN Pump A.-Syrup Heated Parts Identification: X53800-BRN/TAN Pump A.-Syrup Heated (See Figure 3.) ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR. CLASS 1 X36576-TAN X36576-BRN Plunger A. 1 Used to dispense toppings. NNN 1a TAN BRN Knob-Plunger 1 Holds plunger assembly in place. TAN and BRN indicate the hot caramel and hot fudge toppings. 1b Nut-Plunger 1 Threaded nut which holds plunger 103 assembly down on the cover. 1c Tube-Plunger 1 Guides plunger and plunger insert 103 in place. 1d Insert-Plunger 1 Determines the amount of topping 103 dispensed. Factory precut to allow 1 fl. oz. (30 ml.) of topping per stroke. 1e Spring-Plunger-Syrup 1 Returns plunger to ready position. 000 Pump 1f Washer-Nylon 1 Rests on tapered portion of inlet 000 cavity creating tension on spring. 1g Plunger 1 Forces topping up through the 103 outlet spout on the downstroke and fills cavity on the upstroke. 1h X33057 Seal A. 1 Seals and centers the plunger. 000 Includes o-ring (019330) Lid-Pump 1 Covers topping container and 103 holds topping pump body in place Nut-Spout 1 Secures lock in place X53798-SER Pump A.-Syrup Heated 2 Distributes and heats syrup toppings

9 X53800-BRN/TAN Pump A.-Syrup Heated Figure

10 Add the following BRN/RED/TAN Pump A.-Syrup Parts Identification: BRN/RED/TAN Pump A.-Syrup (See Figure 4.) ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR. CLASS BRN RED TAN Knob-Plunger 1 Holds plunger assembly in place. BRN, RED, and TAN indicate the syrup flavor Nut-Plunger 1 Threaded nut which holds plunger 103 assembly down on the cover Tube-Plunger 1 Guides plunger and plunger insert 103 in place Insert-Plunger 1 Determines the amount of syrup 103 dispensed. Factory preset to allow 1 fl. oz. (30 ml.) of syrup per stroke Spring-Plunger-Syrup 1 Returns plunger to ready position. 000 Pump Washer-Nylon 1 Rests on tapered portion of inlet 000 cavity creating tension on spring Plunger 1 Forces syrup up through the outlet 103 spout on the downstroke and fills cavity on the upstroke. 8 X33057 Seal A. 1 Seals and centers the plunger a O-Ring-13/16 OD x 1 Part of X33057 seal assembly W Nut-Spout 1 Secures lock in place Lid-Pump 1 Covers syrup container and holds 103 pump body in place Cylinder-Syrup Pump 1 Chamber to propel the syrup Tube-Discharge 1 Discharges syrup O-Ring-1/5/16 OD x 1 Seals valve W O-Ring-1 OD x.103 W 1 Seals valve Kit-Valve-Captured Ball Shallow 1 Directs syrup flow

11 BRN/RED/TAN Pump A.-Syrup Figure

12 DAILY OPENING PROCEDURES Replace the Daily Opening Procedures in the C708/C716 Operator Manual with the following information: Before performing the opening procedures, check the display panel for any error messages. Normally the display is blank unless an operational fault has occurred. If a fault has been detected, investigate the cause and follow the instructions on the display before proceeding with the opening procedures. (See Failure Messages, in the C708/C716 Operator Manual.) Set-Up - Complete The Following Make sure your hands are clean and sanitized before performing these next steps. 1. With the drain plugs closed, check the water level in the two heated topping wells. Fill the wells with water to the indicating mark on the bottom of the well. 2. Place the topping heaters in the ON position by touching the topping heater symbols. Caution: As soon as the heaters are turned on, the topping wells will begin heating. This heating process will take approximately 2-1/2 hours to reach temperature. The water level in the wells should be checked daily. the way back to its locking position. Place the cones in the drawer and release the spring guide. 8. Prepare a small amount of KAY-5 Sanitizer (HCS) solution. Use one packet in 2.5 gallons (9.5 liters) of water (100 PPM). 9. Return to the freezer with a small amount of sanitizing solution. Dip the door spout brush into the sanitizing solution and brush clean the door spouts and bottom of the draw valves. Note: To assure sanitary conditions are maintained, brush clean each item for a total of 60 seconds, repeatedly dipping the brush in sanitizing solution. 10. Using a clean, sanitized towel, wipe down the freezer door, front panel, the area around the bottom of the freezer door, and any other areas that demonstrate a build-up of either moisture or food substance. 11. Install the front drip tray and splash shield. 12. Install the design caps (C716, only). 13. When ready to resume normal operation, touch the AUTO symbol. (See Figure 5.) 3. Fill the topping containers with topping. Place the caramel and fudge topping containers in the heated wells. Place the remaining two topping containers in the unheated wells. Cover the containers. 4. Sanitize the two topping ladles and place in the cold topping containers. 5. For C708's equipped with optional shake syrup containers and pumps: Remove the syrup pumps and fill the containers with shake syrup. 6. Fill the cup dispensers, cup lid holder, and cone dispenser. 7. To fill the cone dispenser, slide the drawer up and pull out. Push the spring guide all Figure 5 The control has a feature in the Manager's Menu to enable or disable the AUTO START feature. When AUTO START in enabled, the machine will automatically exit the STANDBY mode and start the machine in the AUTO mode at a designated time each day. Note: This procedure should be performed 15 minutes prior to serving product

13 DAILY CLOSING PROCEDURES Replace the Daily Closing Procedures in the C708/C716 Operator Manual with the following information: THIS PROCEDURE MUST BE PERFORMED ONCE DAILY! The function of the Heat Treatment Cycle is to destroy bacteria by raising the temperature of the mix in the freezing cylinder and the hopper to a specified temperature for a specified period of time, and then bringing the temperature back down low enough to retard spoilage. The Heat Treatment Cycle will start at the time designated in the Auto Heat Time. IMPORTANT: The level of mix in the mix hoppers must be above the mix low probe(s). (The mix low light must not be ON.) Note: If the BRUSH CLEAN COUNTER display has counted down to one day, do not add mix. The machine must be disassembled and brush cleaned within 24 hours. The freezer must be in the AUTO (AUTO symbol illuminated) or in the STANDBY mode (STANDBY symbol illuminated) before the HEAT cycle may be started. 1. Place the topping heaters in the OFF position by touching the heater symbols. The symbols will not be illuminated when the heaters are off. 2. Remove the hopper cover(s). Make sure your hands are clean and sanitized before performing these next steps. Note: Pressing either one of the arrow symbols will stop agitator movement. The agitator will automatically restart after 10 seconds. 3. Remove the agitators from the mix hoppers. 4. Remove the design caps (C716, only). 5. Take the agitators, hopper covers and design caps to the sink for further cleaning and sanitizing. 6. Rinse these parts in cool, clean water. 7. Draw a small amount of SolidSense All Purpose Super Concentrate (APSC) (HCS) cleaning solution from the sink proportioner and brush clean the parts. 8. Prepare a small amount of KAY-5 Sanitizer (HCS) solution. Use one packet in 2.5 gallons (9.5 liters) of water (100 PPM). Sanitize the agitator(s) and hopper cover(s). 9. Install the agitators back onto the agitator drive shaft housings. Replace the hopper covers. IMPORTANT: If you do not install the agitators correctly, the machine will fail the heat cycle and lock out in the morning. 10. Return to the freezer with a small amount of cleaning solution. Dip the door spout brush into the cleaning solution and brush clean the door spouts and bottom of the draw valves. Note: To assure sanitary conditions are maintained, brush each item for a total of 60 seconds, repeatedly dipping the brush in cleaning solution. 11. Remove, clean and reinstall all drip pans. (See Figure 6.) Figure

14 12. Using a clean, sanitized towel, wipe down the freezer door, front panel, the area around the bottom of the freezer door, and any other areas that demonstrate a build-up of either moisture or food substance. The heat cycle will start when the clock on the machine reaches the AUTO HEAT TIME set in the Manager's Menu. There are 3 phases of the heat cycle: Heating, Holding and Cooling. Each phase has a time limit. If any one of the three phases fail to reach the proper temperatures within the time limit, the cycle will automatically abort and return to the STANDBY mode. A failure message will appear on the fluorescent display to inform the operator that the machine did not successfully complete the heat treatment cycle. The product may not be safe to serve. The freezer will be locked out (softlock) of the AUTO mode. The operator will be given the option of selecting the HEAT symbol which will begin a new heat cycle, or touching the WASH symbol which will place the freezer into the OFF mode to allow a brush clean of the machine. Note: Once the heating cycle has started, it cannot be interrupted. The heating cycle will take a maximum of 3.5 hours to complete with full hoppers. DO NOT attempt to draw product or disassemble the machine during the HEAT cycle. The product is hot and under extreme pressure. When the heating cycle is complete, the control will return to the STANDBY mode. The STANDBY symbol(s) will be illuminated. WEEKLY CLEANING Add the following Weekly Cleaning information: The topping containers, lids, topping pumps, and water baths require weekly cleaning. For C708's equipped with optional shake syrup containers and pumps: The shake syrup pumps and syrup containers require weekly cleaning. Water Bath Cleaning 1. Place the topping heaters in the OFF position by touching the heater symbols. The symbols will not be illuminated when the heaters are off. 2. Remove the topping container assemblies and take them to the 3-compartment sink for cleaning and sanitizing. 3. Allow the water in the water baths to cool for 10 minutes and then drain the water. 4. Fill the water bath with SolidSense All Purpose Super Concentrate (APSC) (HCS) solution. Use a clean, sanitized towel and thoroughly clean the inside of the water bath. Drain the solution. 5. Fill the water bath with clean tap water. Use a clean, sanitized towel and rinse the inside of the water bath. Drain the water. 6. Use a clean, single service towel and dry the inside of the water bath. 7. Repeat the previous 3 steps to clean the other water bath(s)

15 Topping & Shake Syrup Container Cleaning Note: The heated topping pump has been selected for illustration. The C708 optional shake syrup pump looks slightly different, but the procedures are essentially the same. 4. To remove the knob, compress the spring by holding the nut and pressing on the end of the plunger. Turn the knob counterclockwise. (See Figure 8.) 1. Remove the lids and syrup topping pumps from the syrup containers. 2. Discard the topping from the containers. 3. Rinse the topping containers, lids, and ladles in warm water at the sink. 4. Draw a small amount of SolidSense All Purpose Super Concentrate (APSC) (HCS) cleaning solution from the sink proportioner and brush clean these parts. 5. Prepare a small amount of KAY-5 Sanitizer (HCS) solution. Use one packet in 2.5 gallons (9.5 liters) of water (100 PPM). Figure 8 5. Remove the plunger nut, tube, and insert from the plunger assembly. (See Figure 9.) 6. Sanitize the parts in the KAY-5 Sanitizer (HCS) solution for a minimum of 60 seconds. Allow the parts to air dry after sanitizing. Topping & Shake Syrup Pump Disassembly 1. Flush and rinse the pump in a container of warm water. Place the lower end of the pump into the water container. Operate the pump until only warm water flows from the discharge tube. 2. Remove the pump from the container of water for disassembly. 3. Remove the plunger assembly from the pump body by turning the plunger nut counterclockwise. (See Figure 7.) Figure 9 6. Remove the spring and washer from the plunger assembly. (See Figure 10.) Figure 7 Figure

16 7. Remove the seal assembly from the plunger assembly. (See Figure 11.) 10. Remove the lid by sliding it off the discharge tube. 11. Remove the cylinder from the valve body by turning it counterclockwise (See Figure 14.) Figure Remove the o-ring from the seal. (See Figure 12.) Figure Remove the discharge tube from the valve body by turning it counterclockwise. (See Figure 15.) Figure Remove the discharge tube lock nut by turning it counterclockwise and sliding it off the discharge tube. (See Figure 13.) Figure 15 Figure Remove the 1-5/16 o-ring from the valve body and remove the 1 o-ring from the discharge tube. 14

17 Topping & Shake Syrup Pump Cleaning 1. Wash and scrub all parts in SolidSense All Purpose Super Concentrate (APSC) (HCS). 2. Insert the black shielded brush through the tip of the discharge tube. Move the brush back and forth to scrub the tip of the discharge tube. (See Figure 16.) 5. Insert the black shielded brush into the top side of the outlet valve. Scrub this area, specifically around the steel ball. (See Figure 18.) Figure 18 Figure Advance the brush completely through the discharge tube and pull the brush from the bottom of the tube. 4. Insert the black shielded brush into the top side of the inlet valve. Scrub this area, specifically around the steel ball. (See Figure 17.) 6. Insert the black shielded brush, by the non-bristle end, into the passageway between the inlet valve and the outlet valve. (See Figure 19.) Figure 17 Figure 19 15

18 7. Move the brush back and forth to scrub this passageway. Advance the brush completely, and pull the brush out of the valve body. (See Figure 20.) Topping & Shake Syrup Pump Assembly After pump disassembly and cleaning is complete, assemble the pump. 1. Lubricate and install the seal o-ring into the seal. (See Figure 22.) Figure Insert the black shielded brush into the bottom side of the inlet valve. Move the brush back and forth to scrub this area, specifically around the steel ball. (See Figure 21.) Figure Install the seal assembly onto the piston end of the plunger assembly. 3. Install the washer and spring onto the plunger assembly. (See Figure 23.) Figure 23 Figure Install the plunger insert into the plunger tube by positioning the end of the insert with small hole and beveled edge to enter the plunger tube first. (See Figure 24.) 9. Advance the brush completely through the inlet valve, and pull the brush out of the valve body. 10. Rinse all parts with clear water. 11. Sanitize the parts in KAY-5 Sanitizer (HCS) solution for a minimum of 60 seconds. Allow the parts to air dry after sanitizing. Figure 24 16

19 5. Install the plunger nut onto the plunger tube. (See Figure 25.) 8. Lubricate and install the 1 o-ring onto the groove provided on the discharge tube. (See Figure 28.) Figure Install the flared end of the plunger tube (assembled with insert and nut) onto the plunger assembly. (See Figure 26.) Figure Lubricate and install the 1-5/16 o-ring into the valve body. (See Figure 29.) Figure Holding the nut, press the end of the plunger to compress the spring until the threaded end of the stem projects through the opening on the plunger tube. Install the knob onto the threaded end of the plunger assembly and tighten the knob by turning it clockwise. (See Figure 27.) Figure 27 Figure Install the discharge tube onto the smaller opening in the valve body by aligning the flats on the discharge tube with the locking grooves on the valve body. Push down the discharge tube until it is seated into the valve body opening. Turn the discharge tube clockwise to fully engage it into locking grooves on the valve body. 11. Install the cylinder onto the larger opening in the valve body by tilting the cylinder away from the discharge tube and sliding the widest section of flange under the center locking groove on the valve body. Align the tabs on the cylinder with the locking grooves on the valve body. Turn the cylinder clockwise until the tabs fully engage into the locking grooves on the valve body

20 12. Install the lid by inserting the discharge tube through the smaller hole in the lid. Slide the lid until the larger hole fits around the top of the cylinder. The discharge tube lock nut will secure the lid in position. 13. Install the discharge tube lock nut and tighten, by turning it clockwise. 14. Lubricate the seal assembly and install the plunger assembly into the cylinder opening in the pump body. (See Figure 30.) 15. Tighten the plunger nut by turning it clockwise. (See Figure 31.) Figure 31 Figure 30 LIMITED WARRANTY ON EQUIPMENT Replace the Limited Warranty on Equipment information in the C708/C716 Operator Manual with the following: TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS FOR MCDONALD S Taylor Company, a division of Carrier Commercial Refrigeration, Inc. ( Taylor ) is pleased to provide this limited warranty on new Taylor-branded freezer equipment available from Taylor (the Product ) to the original McDonald s purchaser only. LIMITED WARRANTY Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to defect during the applicable warranty period Taylor, through an authorized Taylor distributor or service agency, will provide a new or re-manufactured part, at Taylor s option, to replace the failed defective part at no charge for the part. C602 C708 C716 Product Part Limited Warranty Period Insulated shell assembly Five (5) years Refrigeration compressor Five (5) years (except service valve) Beater motors Two (2) years Beater drive gear Two (2) years Printed circuit boards Two (2) years Parts not otherwise listed in One (1) year this table or excluded below

21 In addition, during the one (1) year period commencing on the date of original installation of the Product, Taylor will also provide, through an authorized Taylor distributor or service agency, all service needed to replace the failed defective part at no charge for the service. This no-charge service shall not be available for service performed by authorized McDonald s service technicians. Local sales and use taxes may still apply and will be charged accordingly. Except as otherwise stated herein, these are Taylor s exclusive obligations under this limited warranty for a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed below and on the reverse (if any) of this document. LIMITED WARRANTY CONDITIONS 1. If the date of original installation of the Product cannot be verified, then the limited warranty period begins ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of purchase may be required at time of service. 2. This limited warranty is valid only if the Product is installed and all required service work on the Product is performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are used. 3. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the Equipment Manual. 4. Defective parts must be returned to the authorized Taylor distributor or service agency for credit. 5. The use of any refrigerant other than that specified on the Product s data label will void this limited warranty. LIMITED WARRANTY EXCEPTIONS This limited warranty does not cover: 1. Except as otherwise specifically set forth in this limited warranty, labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective parts, replacement parts, or new Products. 2. Normal maintenance, cleaning and lubrication as outlined in the Equipment Manual, including cleaning of condensers. 3. Replacement of wear items designated as Class 000 parts in the Equipment Manual. 4. External hoses, electrical power supplies, and machine grounding. 5. Parts not supplied or designated by Taylor, or damages resulting from their use. 6. Return trips or waiting time required because a service technician is prevented from beginning warranty service work promptly upon arrival. 7. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized alteration or improper operation or use as indicated in the Equipment Manual, including but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies. 8. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty, accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or water supply specification of the Product; or components repaired or altered in any way so as, in the judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration. 9. Any Product purchased over the Internet. 10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or interruption of electrical service. 19

22 11. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever. 12. Damages resulting from the use of any refrigerant other than that specified on the Product s data label will void this limited warranty. 13. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant. 14. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential damages, so this limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. LIMITATION OF WARRANTY THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER. LEGAL REMEDIES The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL

23 LIMITED WARRANTY ON PARTS Replace the Limited Warranty on Parts information in the C708/C716 Operator Manual with the following: TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS Taylor Company, a division of Carrier Commercial Refrigeration, Inc. ( Taylor ) is pleased to provide this limited warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally (the Parts ) to the original purchaser only. LIMITED WARRANTY Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will provide a new or re-manufactured Part, at Taylor s option, to replace the failed defective Part at no charge for the Part. Except as otherwise stated herein, these are Taylor s exclusive obligations under this limited warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed below and on the reverse (if any) of this document. Part's Warranty Class Code or Part Class 103 Parts¹ Class 212 Parts² Class 512 Parts Class 000 Parts Taylor Part # (Motor-24VDC *C832/C842*) Limited Warranty Period Three (3) months Twelve (12) months Twelve (12) months No warranty Four (4) years LIMITED WARRANTY CONDITIONS 1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required at time of service. 2. This limited warranty is valid only if the Part is installed and all required service work in connection with the Part is performed by an authorized Taylor distributor or service agency. 3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation location in the unit of original installation. 4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the Taylor Operator s Manual. 5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit. 6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate Taylor Limited Warranty on freezer or grill equipment. 7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this limited warranty. 1, 2 Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1 (Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment

24 This limited warranty does not cover: LIMITED WARRANTY EXCEPTIONS 1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of defective Parts, replacement Parts, or new Parts. 2. Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator s Manual, including cleaning of condensers or carbon and grease buildup. 3. Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but not limited to the platen and plate, sides of the shroud or top of the shroud. 4. Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials or cleaning processes not approved for use by Taylor. 5. Replacement of wear items designated as Class 000 Parts in the Taylor Operator s Manual, as well as any release sheets and clips for the Product s upper platen assembly. 6. External hoses, electrical power supplies, and machine grounding. 7. Parts not supplied or designated by Taylor, or damages resulting from their use. 8. Return trips or waiting time required because a service technician is prevented from beginning warranty service work promptly upon arrival. 9. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing, unauthorized alteration or improper operation or use as indicated in the Taylor Operator s Manual, including but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning supplies. 10. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty, accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or water supply specification of the unit in which a part is installed; or Parts or the units in which they are installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or normal wear or deterioration. 11. Any Part purchased over the Internet. 12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or interruption of electrical service. 13. Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever. 14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is installed will void this limited warranty. 15. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant. 16. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential damages, so this limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. 22

25 LIMITATION OF WARRANTY THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS, PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER. LEGAL REMEDIES The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL

26

27 OPERATOR'S MANUAL Model C708 & C716 Heat Treatment Soft Serve Freezers Original Operating Instructions M January, 2005 (Original Publication) (Updated 11/21/13)

28 Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: Minimum Wire Ampacity: A A E 2005 Carrier Commercial Refrigeration, Inc M Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be a violation of Copyright Law of the United States of America and other countries, could result in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties. All rights reserved. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL 61072

29 Table of Contents Section 1 To the Installer... 1 Installer Safety... 1 Site Preparation... 1 Air Cooled Units... 2 Water Connections (Water Cooled Units Only)... 2 Electrical Connections... 2 Beater Rotation... 3 Refrigerant... 3 Section 2 To the Operator... 4 Section 3 Safety... 5 Section 4 Operator Parts Identification... 8 Model C Model C Model C708 Single Spout Door and Beater Assembly Model C716 Door and Beater Assembly X57029-XX Pump A. - Mix Simplified (Models C708 & C716) Accessories Brush A.-Package-HT X Section 5 Important: To the Operator Symbol Definitions Operating Screen Descriptions Freezer Locks Manager's Menu Section 6 Operating Procedures Freezing Cylinder Assembly Freezer Door Assembly Mix Pump Assembly Sanitizing Priming Daily Closing Procedures Daily Opening Procedures Manual Brush Cleaning Draining Product From The Freezing Cylinder Models C708 & C716 Table of Contents

30 Table of Contents - Page 2 Rinsing Hopper Cleaning Disassembly Brush Cleaning Section 7 Important: Operator Checklist During Cleaning and Sanitizing Troubleshooting Bacterial Count Regular Maintenance Checks Winter Storage Section 8 Troubleshooting Guide Section 9 Parts Replacement Schedule Section 10 Limited Warranty on Equipment Section 11 Limited Warranty on Parts Section 12 Parts List Wiring Diagrams Note: Continuing research results in steady improvements; therefore, information in this manual is subject to change without notice. Note: Only instructions originating from the factory or its authorized translation representative(s) are considered to be the original set of instructions. E 2005 Carrier Commercial Refrigeration, Inc. (Original Publication) (Updated November, 2013) M Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be a violation of Copyright Law of the United States of America and other countries, could result in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties. All rights reserved. Taylor Company a division of Carrier Commercial Refrigeration, Inc. 750 N. Blackhawk Blvd. Rockton, IL Table of Contents Models C708 & C716

31 Section 1 To the Installer The following information has been included in the manual as safety and regulatory guidelines. For complete installation instructions, please see the Installation Checklist. This unit has many sharp edges that can cause severe injuries. Installer Safety In all areas of the world, equipment should be installed in accordance with existing local codes. Please contact your local authorities if you have any questions. Care should be taken to ensure that all basic safety practices are followed during the installation and servicing activities related to the installation and service of Taylor equipment. S S S S Only authorized Taylor service personnel should perform installation and repairs on the equipment. Authorized service personnel should consult OSHA Standard 29CFRI or the applicable code of the local area for the industry standards on lockout/tagout procedures before beginning any installation or repairs. Authorized service personnel must ensure that the proper PPE is available and worn when required during installation and service. Authorized service personnel must remove all metal jewelry, rings, and watches before working on electrical equipment. The main power supply(s) to the freezer must be disconnected prior to performing any repairs. Failure to follow this instruction may result in personal injury or death from electrical shock or hazardous moving parts as well as poor performance or damage to the equipment. Note:Allrepairsmustbeperformedbyan authorized Taylor Service Technician. Site Preparation Review the area where the unit will be installed before uncrating the unit. Make sure that all possible hazards to the user and the equipment have been addressed. For Indoor Use Only: This unit is designed to operate indoors, under normal ambient temperatures of 70_-75_F (21_-24_C). The freezer has successfully performed in high ambient temperatures of 104_(40_C) at reduced capacities. This unit must NOT beinstalledinanarea where a water jet or hose can be used. NEVER use a water jet or hose to rinse or clean the unit. Failure to follow this instruction may result in electrocution. This unit must be installed on a level surface to avoid the hazard of tipping. Extreme care should be taken in moving this equipment for any reason. Two or more persons are required to safely move this unit. Failure to comply may result in personal injury or equipment damage. Uncrate the unit and inspect it for damage. Report any damage to your Taylor Distributor. This piece of equipment is made in the USA and has USA sizes of hardware. All metric conversions are approximate and vary in size. Models C708 & C To the Installer

32 Air Cooled Units Electrical Connections DO NOT obstruct air intake and discharge openings: Model C708: Requires a minimum of 6 (152 mm) of clearance on both sides and 0 in the rear of the unit. Model C716: Requires a minimum of 3 (76 mm) of clearance on all sides. Install the deflector provided to prevent recirculation of warm air. This will allow for adequate air flow across the condensers. Failure to allow adequate clearance can reduce the refrigeration capacity of the freezers and possibly cause permanent damage to the compressors. Water Connections (Water Cooled Units Only) An adequate cold water supply must be provided with a hand shut-off valve. On the underside of the base pan or on the right side, two 3/8 I.P.S. water connections for inlet and outlet are provided for easy hook-up. 1/2 inside diameter water lines should be connected to the machine. (Flexible lines are recommended, if local codes permit.) Depending on local water conditions, it may be advisable to install a water strainer to prevent foreign substances from clogging the automatic water valve. There will be only one water in and one water out connection. DO NOT install a hand shut-off valve on the water out line! Water should always flow in this order: first, through the automatic water valve; second, through the condenser; and third, through the outlet fitting to an opentrapdrain. A back flow prevention device is required on the incoming water connection side. Please refer to the applicable National, State, and local codes for determining the proper configuration. In the United States, this equipment is intended to be installed in accordance with the National Electrical Code (NEC), ANSI/NFPA The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising from the use of electricity. This code contains provisions considered necessary for safety. In all other areas of the world, equipment should be installed in accordance with the existing local codes. Please contact your local authorities. FOLLOW YOUR LOCAL ELECTRICAL CODES! Each unit requires one power supply for each data label on the unit. Check the data label(s) on the freezer for branch circuit overcurrent protection or fuse, circuit ampacity, and other electrical specifications. Refer to the wiring diagram provided inside of the electrical box for proper power connections. CAUTION: THIS EQUIPMENT MUST BE PROPERLY GROUNDED! FAILURE TO DO SO CAN RESULT IN SEVERE PERSONAL INJURY FROM ELECTRICAL SHOCK! This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized installer. The installation location is marked by the equipotential bonding symbol (5021 of IEC ) on both the removable panel and the equipment's frame To the Installer 2 Models C708 & C716

33 S S S Stationary appliances which are not equipped with a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation. Appliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 ma, particularly when disconnected or not used for long periods, or during initial installation, shall have protective devices such as a GFI, to protect against the leakage of current, installed by the authorized personnel to the local codes. Supply cords used with this unit shall be oil-resistant, sheathed flexible cable not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion. Electrical connections are made directly to the terminal block provided in the main control box, located: C708 - behind the rear panel. C716 - behind the lower front panel. Refrigerant In consideration of our environment, Taylor uses only earth friendly HFC refrigerants. The HFC refrigerant used in this unit is R404A. This refrigerant is generally considered non-toxic and non-flammable, with an Ozone Depleting Potential (ODP) of zero (0). However, any gas under pressure is potentially hazardous and must be handled with caution. NEVER fill any refrigerant cylinder completely with liquid. Filling the cylinder to approximately 80% will allow for normal expansion. Use only R404A refrigerant that conforms to the AHRI standard 700 specification. The use of any other refrigerant may expose users and operators to unexpected safety hazards. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified person, in order to avoid a hazard. Beater Rotation Refrigerant liquid sprayed onto the skin may cause serious damage to tissue. Keep eyes and skin protected. If refrigerant burns should occur, flush immediately with cold water. If burns are severe, apply ice packs and contact a physician immediately. Beater rotation must be clockwise as viewed looking into the freezing cylinder. Note: The following procedures must be performed by an authorized Taylor service technician. To correct rotation on a three-phase unit, interchange any two incoming power supply lines at freezer main terminal block only. To correct rotation on a single-phase unit, change the leads inside the beater motor. (Follow diagram printed on motor.) Taylor reminds technicians to be cautious of government laws regarding refrigerant recovery, recycling, and reclaiming systems. If you have any questions regarding these laws, please contact the factory Service Department. WARNING: R404A refrigerant used in conjunction with polyolester oils is extremely moisture absorbent. When opening a refrigeration system, the maximum time the system is open must not exceed 15 minutes. Cap all open tubing to prevent humid air or water from being absorbed by the oil. Models C708 & C To the Installer

34 Section 2 To the Operator Your freezers have been carefully engineered and manufactured to give you dependable operation. These units, when properly operated and cared for, will produce a consistent quality product. Like all mechanical products, they will require cleaning and maintenance. A minimum amount of care and attention is necessary if the operating procedures outlined in this manual are followed closely. This Operator's Manual should be read before operating or performing any maintenance on your equipment. Your Taylor freezer will NOT eventually compensate for and correct any errors during the set-up or filling operations. Thus, the initial assembly and priming procedures are of extreme importance. It is strongly recommended that personnel responsible for the equipment's operation, both assembly and disassembly, go through these procedures together in order to be properly trained and to make sure that no confusion exists. In the event you should require technical assistance, please contact your local authorized Taylor Distributor. Note: Your Taylor warranty is valid only if the parts are authorized Taylor parts, purchased from the local authorized Taylor Distributor, and only if all required service work is provided by an authorized Taylor service technician. Taylor reserves the right to deny warranty claims on units or parts if non-taylor approved parts or incorrect refrigerant were installed in the unit, system modifications were performed beyond factory recommendations, or it is determined that the failure was caused by abuse, misuse, neglect, or failure to follow all operating instructions. For full details of your Taylor Warranty, please see the Limited Warranty section in this manual. Note: Constant research results in steady improvements; therefore, information in this manual is subject to change without notice. If the crossed out wheeled bin symbol is affixed to this product, it signifies that this product is compliant with the EU Directive as well as other similar legislation in effect after August 13, Therefore, it must be collected separately after its use is completed, and cannot be disposed as unsorted municipal waste. The user is responsible for returning the product to the appropriate collection facility, as specified by your local code. For additional information regarding applicable local laws, please contact the municipal facility and/or local distributor. Compressor Warranty Disclaimer The refrigeration compressor(s) on this unit are warranted for the term stated in the Limited Warranty section in this manual. However, due to the Montreal Protocol and the U.S. Clean Air Act Amendments of 1990, many new refrigerants are being tested and developed, thus seeking their way into the service industry. Some of these new refrigerants are being advertised as drop-in replacements for numerous applications. It should be noted that in the event of ordinary service to this unit's refrigeration system, only the refrigerant specified on the affixed data label should be used. The unauthorized use of alternate refrigerants will void your Taylor compressor warranty. It is the unit owner's responsibility to make this fact known to any technician he employs. It should also be noted that Taylor does not warrant the refrigerant used in its equipment. For example, if the refrigerant is lost during the course of ordinary service to this machine, Taylor has no obligation to either supply or provide its replacement either at billable or unbillable terms. Taylor does have the obligation to recommend a suitable replacement if the original refrigerant is banned, obsoleted, or no longer available during the five year warranty of the compressor. Taylor will continue to monitor the industry and test new alternates as they are being developed. Should a new alternate prove, through our testing, that it would be accepted as a drop-in replacement, then the above disclaimer would become null and void. To find out the current status of an alternate refrigerant as it relates to your compressor warranty, call the local Taylor Distributor or the Taylor Factory. Be prepared to provide the Model/Serial Number of the unit in question To the Operator 4 Models C708 & C716