New Zip AquaFlo. Stainless steel cylinders for mains pressure hot water

Transcription

1 New Zip AquaFlo Stainless steel cylinders for mains pressure hot water

2 2

3 AquaFlo II Zip AquaFlo II is a range of direct and indirect stainless steel cylinders designed to provide mains pressure hot water for powerful showers and fast filling baths. Quick recovery times and high performance insulation ensure that hot water is always available and delivered as economically as possible. Manufactured in the UK from high grade duplex stainless steel, Zip AquaFlo II utilises high quality controls for high flow rates and reliability. Solar compatible options enable Zip AquaFlo II to be integrated into the latest renewable technology water heating systems. Zip AquaFlo II provides: A full range of capacities from 90 to 300 litres for both direct and indirect applications Coil-in-coil heat exchangers ensure quick recovery and maximum effective capacity (up to 96% of the nominal capacity) High performance insulation and fast recovery times translate into high efficiency and big savings in energy External expansion ensuring: More effective use of the cylinder volume More usable space around the unit Reduced maintenance and greater reliability with no air bubble to lose Easier installation from: A slim profile and footprint with a diameter of 545mm The use of standard compression fittings throughout Minimal maintenance required due to: External expansion No sacrificial anode High quality construction, materials and electrical components for longevity and complete peace of mind. Backed by a transferable 25 year on-site parts and labour warranty on the cylinder and 2 year, on-site parts and labour warranty on all other components Duplex Stainless Steel cylinder with superior corrosion resistance means years and years of service from your Zip AquaFlo after which it can be completely recycled Zip products are in daily use in tens of thousands of locations in London and across the UK. 3

4 Applications and Installation Domestic Applications Type of property Direct Indirect Bedsit / 1 Bed AF3120 AF4090 1/2 Beds 1 Bath & Shower AF3150 AF Beds 1 Bath & Shower AF3180 AF Beds 1 Bath & Shower AF3210 AF4180 4/5 Beds 2 Baths & Showers AF3250 AF4210 4/6 Beds 3 Baths & Showers AF3300 AF4250 Commercial Applications For commercial applications Zip AquaFlo units should be selected to ensure that sufficient total capacity and flow rate is available for all outlets to be served Volume of hot water required at 60 C per outlet Wash basins Sinks Showers Baths Up to 5 litres 10 to 15 litres 30 litres (at 10 l/min) 60 litres Refer to Technical Data on page 6 to ensure that the correct kw loading is selected for the required heat up and recovery performance The above are for guidance only and the requirements of specific installations should be determined Siting the Unit Zip AquaFlo can be positioned more or less anywhere in the building but it should be remembered that for every 1 metre that an outlet is above the AquaFlo, the pressure will be reduced by 0.1 bar. If siting outside the heated envelope of the building such as in a garage or outbuilding then frost protection should be provided and exposed pipework should be insulated. Zip AquaFlo must be supported on a flat base capable of supporting the weight of the cylinder when full. The minimum recommended cupboard size is 650mm square. It s important that consideration is given to access for maintenance of the valves. The immersion heaters are 375mm long and access space should be provided for their possible future replacement. Water Supply AquaFlo is capable of delivering over 50 litres per minute when connected to a suitable mains supply. The high quality inlet control set with a 3 bar operating pressure has been designed to make the most of what is available, however the performance of any unvented system is only as good as the water supply. In unvented systems both hot and cold services are supplied simultaneously from the mains so the maximum possible on-site water demand must be assessed and the water supply should be tested to ensure it can meet these requirements. Consult the local water supplier if necessary regarding the likely pressure and flow rate availability. Plumbing For connection to 22mm mains potable water supply Minimum water supply 1.5 bar, 20 l/min Maximum water supply pressure 12 bar Electrical To be wired to a suitably rated double pole fused spur Installation must comply with current IEE regulations Connecting Zip AquaFlo Units in Parallel Multiple Zip AquaFlo units can be connected in parallel for applications where higher storage capacity is required. To connect in parallel, each Zip AquaFlo should be provided with a separate cold supply while the hot outlets are connected to a common pipeline. Secondary Return All Zip AquaFlo units are suitable for use with secondary return systems. A dedicated secondary return connection is provided on AquaFlos with a capacity of 210 litres and above. On smaller sizes the secondary return can be connected to the incoming supply. Always check that the kw loading available on direct units is sufficient to recover the heat loss in the secondary circuit in addition to any hot water drawn off. Installation Installation must be undertaken by a competent installer in accordance with all national and local Building Regulations. Zip AquaFlo is intended for floor standing only refer to Technical Data on page 6 for weights when full. 4

5 Product Specification Construction Direct, indirect and solar compatible unvented water heaters Corrosion resistant Duplex Stainless Steel cylinder High performance, low profile coil-in-coil heat exchanger High performance CFC-free injected polyurethane foam insulation White plastic coated steel case resistant to scuffing External expansion for reliability and ease of maintenance Cylinder pressure tested to 15 bar Solar Compatible Cylinders Zip AquaFlo Solar cylinders have been specifically designed for use with solar heating systems and feature a high efficiency heat exchanger to extract maximum benefit from the solar energy that is available. Solar compatible cylinders are also available in both direct and indirect construction. Nominal Capacity Direct and Indirect units: 90, 120, 150, 180, 210, 250 and 300 litres Solar Twin Coil and Solar Direct units: 150, 180, 210, 250 and 300 litres Immersion Elements Incoloy construction 1¾ thread. Length 14 Loading 240V Diagrams Showing Connection Points Heat Exchanger 22mm low profile, high efficiency stainless steel coil-in-coil Controls Thermostat adjustable up to 65 C Over temperature safety cut-out Manually re-settable. Operates at 85 C Expansion relief valve 6 bar Temperature and pressure relief valve 90 C and 7 bar Pressure reducing valve 3 bar Expansion vessel Pre-charged to 3 bar L units 12L vessel L units 18L vessel 300L units 24L vessel Approvals KIWA approved to UK Water Regulations and UK Building Regulations Part G3 and Part L Immersion element/thermostat BEAB approved and CE endorsed Warranty On site parts and labour: 25 years transferable on cylinder (conditions apply) 2 years warranty on all other components Aquaflo Direct Aquaflo Indirect and Solar Compatible 38 Immersion* Immersion 45 Cold Inlet 38 Immersion* 15 T&P Valve *Multi element options only AF3150S AF3300S 66 Sec Return 40 Primary Coil 25 Stat Pocket 45 Cold Inlet Primary Coil T&P Valve Immersion 5

6 Technical Data AquaFlo Direct Nominal Height Weight Weight Vol within Heat up Heat up Heat up Boost Low level High level Standing Capacity (mm) x Empty Full 10ºC of set 3kW 6kW 9kW re-heat immersion immersion Loss Model (L) 545 Dia (kg) (kg) temp (L) (mins) (mins) (mins) (mins) elements elements (kwh/day) AF AF AF AF AF AF AF AF3150S* # 3 or 2 0 or AF3180S* # 3 or 2 0 or AF3210S* # 3 or 2 0 or AF3250S* # 3 or 2 0 or AF3300S* # 3 or 2 0 or * Supplied with 3 elements and 4 bosses - 3 at low level and 1 at high level. Additional elements are available for installation in the 4th boss. # If using high level element AquaFlo Indirect Nominal Height Weight Weight Vol within Indirect Heat Recovery Boost Low level High level Standing Capacity (mm) x Empty Full 10ºC of set Exchanger Indirect re-heat immersion immersion Loss Model (L) 545 Dia (kg) (kg) temp (L) (kw) (mins) (mins) elements elements (kwh/day) AF AF AF AF AF AF AF AquaFlo Solar Compatible Nominal Height Weight Weight Vol within Indirect Heat Solar Dedicated Recovery Boost Low level High level Standing Capacity (mm) x Empty Full 10ºC of set Exchanger Heat Solar solar re-heat immersion immersion Loss Model (L) 545 Dia (kg) (kg) temp (L) (kw) Exchanger Capacity (mins) (mins) elements elements (kwh/day) Solar Twin Coil AF * 12.0# AF * 14.8# AF * 15.5# AF * 20.0# AF * 25.0# Solar Direct AF * AF * AF * AF * AF * * Re-heat times based on BS12897 parameters with an 80 C primary flow at 15 l/min. # Using Indirect heat exchanger Actual performance when installed will vary considerably dependant on the rate of solar or other renewable input, number of panels etc. 6

7 Dimensions H1 G1 C1 H1 G2 C2 B1 A1 A2 F1 B2 D1 Direct Indirect H2 G2 H2 G2 F3 B3 E1 C3 A3 F2 D2 A3 F2 B4 D2 Solar Twin Coil Solar Direct Cold Inlet Immersion 1 Immersion 2 Bottom Coil Top Coil Stat Pocket Sec Return T&P Valve Capacity Height Diameter A1 A2 A3 B1 B2 B3 B4 C1 C2 C3 D1 D2 E1 F1 F2 F3 G1 G2 H1 H2 90L L L L L L L

8 Zip sets new standards in Customer Care with the largest team of directly employed engineers in its sector, providing comprehensive on-site maintenance, repair and installation packages Zip Heaters (UK) Ltd Bertie Ward Way, Dereham, Norfolk NR19 1TE Customer Service Tel: The terms Zip and Aquaflo are registered trade marks of Zip Industries Zip Heaters (UK) Ltd, January 2010