WaterWorks _ Reverse Osmosis
|
|
- Gwendolyn Phelps
- 5 years ago
- Views:
Transcription
1 WaterWorks _ Reverse Osmosis DRINKING WATER SYSTEM Model RO 1000 Installation Operation Maintenance Repair Parts IF YOU HAVE QUESTIONS WHEN INSTALLING, OPERATING AND MAINTAINING YOUR REVERSE OSMOSIS SYSTEM... CALL TOLL FREE WATER Manufactured by EcoWater Systems, Inc. PO BOX 64420, ST. PAUL, MN Part No (10/99)
2 - WARRANTY - FULL WARRANTY ON REVERSE OSMOSIS DRINKING WATER SYSTEM I, (except filter cartridges and R. O. membrane) I I For one year from the date of purchase, when the Reverse Osmosis Drinking Water System is installed I and maintained in accordance with our instructions, Sears will repair, free of charge, defects in material t and workmanship, except filter cartridges and the R. O. membrane. Q! I TO THROUGHOUT OBTAIN WARRANTY THE UNITED SERVICE, STATES. SIMPLY This warranty CONTACT applies THE NEAREST only while this SEARS product SERVICE is in use CENTER in the I ' United States.! I This warranty gives you specific legal rights, and you may have other rights which vary from state to state. I! I, Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL 60179, L_... _J SEARS INSTALLATION POLICY All installation labor arranged by Sears shall be performed in a neat, workmanlike manner in accordance with generally accepted trade practices. Further, all installations shall comply with all local laws, codes, regulations, and ordinances. Customer shall also be protected, during installation, by insurance relating to Property Damage, Workman's Compensation and Public Liability. SEARS INSTALLATION WARRANTY In addition to any warranty extended to you on the WaterWorks merchandise involved, which warranty becomes effective the date the merchandise is installed, should the workmanship of any Sears arranged installation prove faulty within one year, Sears will, upon notice from you, cause such faults to be corrected at no additional cost to you. - SAFETY GUIDES - Read all steps, guides and rules carefully before installing and using your reverse osmosis system. Follow all steps exactly to correctly install. Reading this manual will also help you to get all the benefits from the reverse osmosis system. Do not attempt to use this product to make safe drinking water from non-potable water sources.do not use the system on microbiologically unsafe water, or water of unknown quality. Check with your local public works department for plumbing and sanitation codes. You must follow their guides as you install the system. Follow your local codes if they differ with guides in this manual. The reverse osmosis system works on water pressures of 40 psi (minimum) to 125 psi (maximum). If your house water pressure is over the maximum, install a pressure reducing valve in the water supply pipe to the reverse osmosis system. Do not install the reverse osmosis system outside, or in extreme hot or cold temperatures. Temperature of the water supply to the reverse osmosis system must be between 40 F and 100 F. Do not install on hot water. Read the other limits (ph, hardness, etc.) in the specifications and be sure your water supply conforms. Also see "Water Supply" on page 3. The reverse osmosis membrane contains a preservative for storage and shipment. Be sure to purge as instructed on page 9 before using product water.
3 - TABLE OF CONTENTS - Where To Install the RO System... 4 Tools and Materials Needed... 4 Installation Steps Cold Water Supply Saddle Valve... 5 Drain Adapter... 6 Faucet RO Assembly... 7 Storage Tank, Tubing Connections... 8 Installation Steps - continued Sanitizing, Pressure Test, Purging... 9 How the RO System Works Care of RO System Dimensions, Specifications Repair Parts Remote Installation Locations WHAT YOUR REVERSE OSMOSIS SYSTEM WILL DO - Your Reverse Osmosis (RO) Drinking Water System is a water treatment unit. It uses household water pressure to reverse a natural physical process called osmosis. Water, under pressure, is forced through a semi-permeable membrane where minerals and impurities are filtered out. Clean drinking water goes to the faucet or storage, while minerals and impurities are sent to the drain with RO waste water. The minerals and impurities are measured in water as total dissolved solids (TDS). The system includes replaceable pre and postfilter sediment-carbon cartridges. The prefilter removes sand, silt, dirt, rust particles, other sediments, and chlorine from the water supplybefore it can enter the RO membrane. The postfilter removes any tastes and/or odors that may remain in the water, after passing through the RO membrane, and just before going to the RO faucet. To prevent water waste, an automatic shutoff valve closes when the RO faucet is closed and the storage tank is full. Your reverse osmosis system gives you a continuous supply of sparkling clear, delicious water for drinking, cooking and other uses. Foods will look and taste better too. Having high quality RO product water at your fingertips eliminates the need to buy bottled water. The storage tank holds over 2 gallons of RO product water for your needs. - BEFORE YOU BEGIN TO INSTALL THE RO SYSTEM - Check Your Water Supply: The cold water supply to the RO system must be within certain quality limits. See the specification table on page 15. If supply water is not within limits, the RO system can not make product water as it should and reduced RO membrane life will result. Trained salespeople at Sears can arrange for a free water analysis. The analysis will tell you if other water supply treatment is needed before going to the RO system. CAUTION: Chlorine in the water will destroy the RO membrane. Most cities add chlorine to the water supply to kill bacteria. The prefilter removes chlorine up to the limits shown in the specifications before it enters the RO membrane. It is important to replace the prefilter cartridge at least every 6 months. See the RO care guide on page 14. Check Parts Included: Unpack the carton and remove the RO system. In addition to the assembled RO and the storage tank, the system includes the parts illustrated below, a separate length of tubing, and this manual. [ F,G. 1] ; WATER_AUCET1 I ROPRODUCT I (,I ADAPTERS _ I WATER SUPP_ SADDLE VALVE [ F 7 I_ DRAIN I I '7 i 'I_ADAPTER! HANGER I I SCREWS I I 3
4 - WHERE TO INSTALL THE RO SYSTEM - The RO assembly and storage tank is designed for installation under the sink, usually in the kitchen or bathroom. The RO assembly mounts on a wall surface, or can lay on the cabinet floor next to the storage tank. Hanger washers and wood screws are included for cabinet wall mounting. The RO product water faucet installs on the sink or on the countertop next to the sink (pages 6 and 7). Note: Tubing lengths allow for the removal of the assembly from the hanger washers for servicing. If tubing lengths are shortened for nearer appearance, it may be necessary to keep the assembly on the hanger washers for service. You can also locate the RO assembly and storage tank in any remote location from the faucet, observing I FIG. 2 ] J cold water supply II II safety guides on page 2. You do need a nearby water source and drain point (see page 18). Water Supply: To provide supply water to the RO system inlet, a saddle valve is included to install (where codes permit) on a cold water pipe, page 5. Provide other pipe fittings for tubing connection, as typically shown on page 5, where saddle valves are not allowed. Drain Point: A suitable drain point is needed for reject water from the RO membrane. A floor drain, laundry tub, standpipe, sump, etc., is preferred, as shown in the remote locations drawing, page 18. A sink p-trap drain adaptor is included to install where codes permit, as an optional drain point (page 6). RO product water faucet --, ;_: _'_ drain adapter Storage Tank t sink drain p-trap RO Assembly - TOOLS AND MATERIALS NEEDED - _- adjustable wrench, standard pliers, and larger adjustable jaw pliers or pipe wrench to fit sink drain plumbers slotted and putty Phillips head screwdrivers _- pipe joint compound (thread seal) or Teflon tape, approved for use on potable water supplies hand or battery powered drill with 1 / 8" bit (if needed for the cold water supply valve, page 5) _P- electric drill and bits, if hole is needed for the RO faucet, page 6 and 7-6 STEPS TO INSTALL - STEP 1: - Install Cold Water Supply Saddle Valve, or other fittings - page 5 STEP 2: - Install Drain Adapter - page 6 STEP 3: - Install Faucet - pages 6 and 7 STEP 4: - Install RO Assembly - page 7 STEP 5: - Install Storage Tank, Make Remaining Tub_ ing Connections - page 8 STEP 6: - Sanitizing, Pressure Testing, Purging - page 9 4
5 - STEP 1: INSTALL COLD WATER SUPPLY SADDLE VALVE - Check and comply with local plumbing codes as you plan, then install a cold feed (supply) water fitting. The fitting must provide a leak-tight connection to the RO 1/4" tubing (see FIG. 8, page 8). A typical connection, using the included saddle valve is shown in FIG.3 - A below. An optional connection, using standard plumbing fittings (not included), is shown in B. Note: Codes in the state of Massachusetts require instal- r ] FIG. 3 lation by a licensed plumber, and do not permit the use L J of the saddle valve. For installation, use plumbing chusetts, A. SADDLE VALVE Note: This valve has a cutting pin and will pierce a hole in copper tubing or plastic pipe. If installing on iron pipe, you have to drill a 1 / 8" hole for the piercing pin. Read the following danger note and be sure to turn off water to the pipe and to drain water from it before drilling. code 248-CMR of the Commonwealth of Massanut (2) - not req'c with clamp Z clamp Z A. WATER SUPPLY CONNECTION (using included saddle valve) pre-drill I" 1/8" hole Check local iron pipe I codes for seal clamp X valve L approval DANGER (if drilling metal pipe): To protect yourself from serious inj ury or fatal shock, use a battery powered hand drill only to make the hole. Do not use an electric drill. 1. Close the house main water shutoff valve and open faucets to drain water from the sink cold water pipe. 2. Observing above note and caution, drill the 1/8" diameter hole in iron pipe. 3. Looking at figure 3A, turn the valve into clamp X and tighten (maybe already assembled). Turn the valve handle all the way out. 4. Place the seal on the inside of clamp X as shown. Be sure the cutting pin does not stick out beyond the seal. 5. Place clamp X and Z around the pipe and secure in place with 2 screws. If you predrilled a 1/8" hole, align the cutting pin with it. Tighten both screws evenly, but do not overtighten. Clamp Z will either have threaded screw holes, or 2 nuts are included. 6. Carefully turn the handle inward to pierce a hole in the copper or plastic pipe. B. OPTIONAL PIPE FITTINGS (compression type shown) Note: Be sure to turn off the water supply and open a low faucet to drain the pipe. insert See note on codesl use to connect in the state of tubing, step 2, Massachusetts, on page 8 above left. \!- ( handle Cold water shutoff a. WATER SUPPLY TYPICAL CONNECTION f (using compression fitting) - parts not included - 1/4" compression fitting insert ferrule Complying with plumbing codes, install a fitting on the kitchen cold water pipe to adapt 1/4" OD tubing. A typical connection is shown in figure 3B. If threaded fittings are used, be sure to use pipe joint compound or Teflon tape on outside threads. cold water pipe 1/4" tubing to RO inlet (see step 2, on page 8) 5
6 - STEP 2: INSTALL DRAIN ADAPTER - [] Note: Running the drain tubing directly to a floor drain, sump, standpipe, laundry tub, etc., as shown on page 18, is preferred. However, if that is not possine or practical, the included drain adapter installs in the sink drain pipe, always above or ahead of the p-trap (FIG. 4). Be sure to comply with your local plumbing codes. Other drain pipe fittings, in addition to the adapter, may be needed. [] The drain adapter fits 1-1/2" sink drain pipe. [] The adapter installs directly onto the sink tailpiece as typically shown in FIG, 4 and 5. [] Locate so drain tubing from the faucet (installed in step 1, page 8) makes a straight run to the adapter, without dips, loops, low spots or kinks. Note: Consult a plumber if you are not familiar with plumbing procedures. FIG, 4 ] FIG. 5 ] 1. Use a ferrule and nut to assemble the drain tubing connector to the drain adapter (FIG. 5). Turn the connector to about 45 o from the 12:00 position, as shown (to 10:00 or 2:00 position as needed). Tighten the nut securely. 2. Carefully disassemble the sink drain pipe and clean the tailpiece to assure a leak-tight fit. ferrule 0 3. Install the drain adapter onto the sink tailpiece, using a ferrule and nut. Snug the nut, but do not tighten. X_f459q,.t,,,- Note: If needed, to make fit, you can cut to shorten the unthreaded end of the adapter. Do not cut too short so the adapter willmake a leak-tight seal with the connecting fitting. cut, if needed drain tubing connector 2:00 4. Assemble the p-trapto the drain adapter, and other drain pipe fittings as required (check codes) to complete the drain run. 5. Tighten all connections, but do not overtighten and break plastic fittings. - STEP 3: INSTALL FAUCET - A. PREPARE MOUNTING HOLE 1. Select 1 of the following places for the faucet. Be sure it will fit flat against the surface, and there is space underneath for tubing (see FIG. 8, page 8). Use an existing sink top hole for a spray hose or other faucet. A 1" to 1-1/4" diameter hole is needed. j Drill a new hole in the countertop next to the sink. Drill a new bole in the sink top. CAUTION: To avoid damaging a sink beyond repair, consult a qualified plumber or installer for guides to drill holes in porcelain or stainless steel. 2. If drilling is needed, make the 1" to 1-!/4" diameter hole. 3. Place plumbers putty around the drilled hole (FIG. 6) to prevent water leakage around the base of the faucet.
7 B. ASSEMBLE FAUCET - STEP 3: INSTALL FAUCET (cont.)- 1. If not already assembled, install the rubber washer, spacer, flat (or lock) washer and hex nut onto the threaded faucet stud. FIG. 6 ] 2. Apply Teflon tape to the end of the faucet stud. Turn the tubing adapter with a blue collet onto the stud and tighten. 3. Wet the o-ring seals on the faucet spout. Then, remove and discard the short piece of tubing from the faucet body and insert the spout in it's place. 4. CONNECT TUBING TO FAUCET AS FOLLOWS. a. Take the separate length of 3/8" black tubing and, putting end through the larger hole in the rubber washer, slide end onto the larger barb fitting on the bottom of the faucet. Note: To soften end of tubing, hold under hot water. in t piece l I ASSEMBLED IN MOUNTING HOLE /aucet & spout _)_" tubing barb fittings rubber washer b. Route 1/4" red tubing from RO up through the sink hole and slide end onto the smaller barb fitting (heat end if needed) on the faucet. c. Route 3/8" blue tubing from RO up through the sink hole and push end all the way into the tubing adapter fitting on the bottom of the faucet. Pull on the tubing to be sure it's held firmly in the adapter fitting. See pages 12 and 13 for tubing connection instructions. space steel washer _hex t[- nut /s pace r flat (or lock) washer hex nut _ ubing adapter blue collet 5, Lower the faucet into the sink or countertop hole. 6. On the underside of the sink or countertop, insert the large steel washer between the mounting hole and the spacer on the faucet stud (see assembled view). Then, turn the hex nut up to the spacer and tighten. Tighten the hex nut so the faucet can not move, but do not overtighten and break the faucet. - STEP 4: INSTALL RO ASSEMBLY - steel was_r._ /'/ I Io hole in sink or _=_ I_ F countertop /_ H _ 1/4" redtubing 3/8"blaektubing / / \ \\ /fromrodrain 3/8" blue- TUBING FROM tubing RO SYSTEM Hang the assembly on the included hanger washers, or lay on the cabinet floor, as desired. 1. Refer to FIG. 7 for wall mounting. Hold the assembly up to the wall surface and mark locations for the hanger washers. Indicator marks on top of the bracket are the needed 10-1/2" apart. 2. Install hanger washers at least 15-1/2" up from the cabinet floor, allowing room to remove sumps from filter heads. Wood screws are provided, or obtain other fasteners as needed. 15-1/2" min. up from floor 7
8 - STEP 5: INSTALL STORAGE TANK, MAKE REMAINING TUBING CONNECTIONS - 1. CONNECT DRAIN TUBING, FAUCET TO DRAIN ADAPTER: Referring to FIG. 8, run the loose section (connected to faucet barb fitting) of black 3 / 8" tubing from the faucet to the drain adapter, with a black collet, installed on page 6. Cut this tubing as needed to route in as straight of a run as possible, without loops, dips, low spots or kinks, Cut the end of the tubing square. Then, push all the way into the fitting. Pull on the tubing to be sure it's held firmly in the adapter fitting. See pages 12 and 13 for tubing connection instructions. 2. CONNECT TUBING TO WATER SUPPLY: Use the tubing insert, ferrule and nut to fasten the 1 / 4" green tubing to the saddle valve fitting installed on page 5. Tighten the nut with a wrench. 3. Move the storage tank into place next to the RO assembly. You can stand the tank upright, or lay it on side. Apply Teflon tape to the threads on the nipple at the top of the tank. Turn the other included tubing adapter fitting with the yellow collet onto the tank nipple. 4. Run the 3/8" yellow tubing to the fitting installed in step 3. Be sure the end of the tubing is cut square, and insert all the way into the fitting. Again, pull on the tubing to be sure it's held firmly in the fitting. FIG. 8 ] TYPICAL UNDERSINK INSTALLATION RO product water faucet See note on codesinthe state of Massachuse_s page 5. watersupply HOT COLD valve drain adapter p-trap g, to larger barb on faucet Note: See note on page 4 regarding tubing lengths. nut ferrule CLOSE insert yellow collet tubing adaptor
9 - STEP 6: SANITIZING, PRESSURE TESTING & PURGING -- SANITIZING Sanitizingisrecommended upon installationof the RO system, and afterservicinginner parts.itisimportant for the service person to have clean hands while handling inner parts of the system. CAUTION: Be sure to remove the RO membrane and both filter cartridges as follows, before sanitizing. Chlorine will destroy the RO membrane cart iag. 1. Be sure the water supply to the RO is turned off, and the RO faucet is open to relieve pressure. 2. Referring to FIG. 9, page 11, press inward while turning the RO cap to the left (_) to remove from the bracket/membrane housing. Remove (use pliers) the RO cartridge from the housing. Place the cartridge in a clean plastic bag. 3. Be sure the o-ring seal is in the RO cap. Replace the RO cap and push inward while turning to the right (_) to lock. 4. Remove the postfilter sump, turning to the left. Take the cartridge from the sump and place in the plastic bag. Replace the sump and tighten securely. 5. Remove the prefilter sump and cartridge. Also place this cartridge in the clean bag. 6. If needed to clean, flush the prefilter sump with flesh water. Then, fill with water to about 1" from the top. Add 1.0 ounce of chlorine (ordinary 525% household bleach...hilex, Clorox, etc.) and mix in the water. Do not add chlorine first. Concentrated, it will attack plastics. 7. Carefully replace the sump on the prefilter head and tighten securely. 8. Slowly open the water supply to the RO. 9. Open the RO faucet, locking the lever upward, against the spout. 10. Allow water to circulate through the RO system until you smell the bleach odor. Then dose the faucet and allow the RO to stand idle for 20 minutes. 11. After the 20 minutes, open the RO faucet and run water until the bleach odor is gone. 12. Turn off the water supply to the RO. 13. Be sure your hands are clean. Then, repeat steps 1-5 and 7, only replace all cartridges. Important: Refer to FIG. 9, page 11, and to page 12 when replacing cartridges. The preffiter (left side) cartridge has light gray coloring, and the postfilter (right side) has blue coloring. PRESSURE TESTING 1. Do the preceding sanitizing procedures before pressure testing. 2. Open the water supply shutoff valve to the RO. 3. Open the main water supply valve and several house faucets to purge air from the system. Close faucets when water runs smooth. 4. In about 2 hours, pressure will start to build in the RO system. Then, carefully check all fittings and connections for water leaks. Correct leaks if any are found. Note: When the system is first pressurized, water may "spurt" from the faucet airgap hole until air is expelled from the RO system. PURGING RO MEMBRANE Important purging instructions: The RO cartridge contains a food g'ade preservative that you should clean from it before using water from the system. The preservative will give product water an unpleasant taste and odor. 1. Allow the storage tank to fill for about 4 hours. Then, open the RO faucet until the tank is empty and flow stops. 2. Close the RO faucet and allow the tank to fill again for 4 hours. Then, open the RO faucet and empty again. Repeat steps I and 2 to purge the storage tank 4 times. Then, the RO system is ready to make product water for use.
10 - HOW YOUR REVERSE OSMOSIS SYSTEM WORKS - PREFILTER Water from the cold supply pipe enters the RO assembly prefilter first (FIG. 8 and schematic below). The prefirer has a replaceable sediment cartridge with activated carbon in its composition. The cartridge (10 micron) removes sand, silt, dirt, other sediments, and up to the ppm of chlorine shown in the specifications from the feed water. Chlorine will destroy the RO membrane. Filtered, clean, chlorinefree water flows from the prefilter, to the RO membrane cartridge. IMPORTANT: See prefilter maintenance, page 11. REVERSE OSMOSIS (RO) CARTRIDGE The cartridge inside of the RO housing, is a tightly wound, special membrane. Water is forced through the cartridge and the membrane removes the dissolved solids and organic matter, High quality product water (_tbout i ounce per minute) exits the RO housing and goes to the storage tank or to the post- _ter and RO faucet. Reject water, with the dissolved solids and organic matter, is routed through the flow control and to the drain. STORAGE TANK The storage tank holds up to 2.3 gallons of product water, A diaphragm inside the tank keeps water pressurized to about 30 psi, when the tank is full, to provide fast flow from the RO faucet. The tank when empty, is pressurized to 5-7 psi. POSTFILTER After leaving the storage tank but before going to the RO faucet, product water goes through the postfilter The postfilter is an activated carbon type filter Any remaining tastes and odors are removed from the product water. Taste-f-me, odor-f_e, clean, high quality drinking water is available for use. FAUCET The sink or countertop faucet has a hand operated, spring-loaded closed lever to prevent the waste of drinking water. You can also keep the faucet open by pushing upward on the lever and locking it against the faucet spout. To comply with plumbing codes, an air-gap is built into the faucet drain water connection. SHUTOFF ASSEMBLY To conserve water, the drinking water system has an automatic shutoff system. When the storage tank has filled to capacity, and the drinking water faucet is closed, pressure closes the shutoff to stop flow into the RO. Pressure in the storage tank is about half of the water supply pressure. After drinking water is used, and pressure in the system drops, the shutoff opens to allow water flow again. CHECK VALVE A checkvalve (FIG. 10) is located in the outlet end of the RO housing, opposite of the cap. The checkvalve prevents a backward flow of product water from the storage tank. A backward flow could rupture the RO membrane. FLOW CONTROL Water flow through the RO membrane is regulated by the flow control. It maintains the desired flow rate to obtain the highest quality drinking water. The flow control is located in the end of the 1 / 4" red drain tubing, at the RO housing drain port. A small coneshaped screen fits over the end of the flow control to help prevent plugging with drain water sediments. PRODUCT WATER FAUCET air gap _ RED YELLOW REVERSE OSMOSIS,I, d_o_,oow SCHEMATIC lb" _1]_ RO MEMBRANE g r" 'Y I BLUE PRODUCT WATER check II _ f f f _l 1' _,_p R AUTO MATIO _- _ [_1 # SHUTOFF _ L.. J WATER IN GREEN 10
11 - CARE OF YOUR REVERSE OSMOSIS SYSTEM - To keep your reverse osmosis system operating and making high quality water, you must make sure supply water is always within the limits shown in the specifications. Good supply water helps to assure longer life from the RO membrane cartridge, prefilter and postfilter cartridges. However, each of these will wear out in time and need replacement. This reverse osmosis system contains a replaceable treatment component critical for effective removal of total dissolved solids. The water should be tested periodically to verify the system is performing satisfactorily. Note: The prefilter cartridge has light gray netting and end caps. The postfilter has blue. Do not interchange. *Note: Use a lubricant approved for use on a potable water supply. mounting FIG. 9 -'1t washers (2) (RO cartridge o-ring seals on this end) If the RO assembly is wall mounted, you may be able to replace parts with the assembly left on the wall. If not, simply lift the RO assembly from the mounting washers and lay on the cabinet floor when replacing the prefilter and post filter cartridges and RO membrane. prefilt_ cartridge RO Ca_ridge Note: To prevent spillage, place a container under the RO assembly, or put the RO assembly in a container to catch the water. CAUTION: Before disconnecting parts, be sure to close the water supply valve to the RO. PREFILTER AND POSTFILTER CARTRIDGES You must replace the prefilter cartridge often to protect the RO membrane from being destroyed by chlorine, and / or from plugging with sediments in your water supply. If the water supply contains both chlorine and sediments, replace the prefilter cartridge at least every 6 months of product water use. Replace more often than 6 months if it begins to plug with sediments. If the water has sediments only, with no chlorine, you may notice a slower making of product water as the prefilter collects the sediments. When this occurs, replace the prefilter cartridge. Also replace the postfilter cartridge. To replace the filter cartridges (see FIG. 9): 1. Turn off the water supply and open the RO faucet to relieve pressure. 2. Remove (turn to the left) both sumps from the filter beads. Be careful...the sumps are full of waten 3. Remove and discard the inner cartridges in a proper mannen Flush the insides of the sumps with fresh water. Do not lose the large o-ring seals. 4. Insert new cartridges, and with lubricated* o-rings in place, turn on and tighten tbe sumps. Turn sumps in the direction of the arrow to remove. Turn opposite way to install and tighten. Ii I o-ring o-ring seal seal sump RO MEMBRANE CARTRIDGE l RO cap The life of the RO membrane cartridge depends mostly on the ph of the supply water to the RO system (see specifications). Cartridge life is shorter with higher ph. For example, if supply water ph is from 6.8 to 7.7, the cartridge may last for well over I year. HoweveT; cartridge life may be as short as 6 months if the ph is as high as 8.5 to 10. Higher ph weakens the cartridge membrane and causes pin-hole leaks. It's time to replace the RO cartridge when the production rate and/or quality of product water drops. Product water may begin to taste different or bad, indicating solids and organics are passing through the RO membrane. To be sure it is the RO cartridge, replace the prefilter and postfilter cartridges first. To replace the RO cartridge (see FIG. 9): 1. Turn off the water supply and open the RO faucet to relieve pressure. continued 11
12 - CARE OF-YOUR REVERSE OSMOSIS SYSTEM - 2. Press inward while turning the RO cap to the left (_) to remove from the bracket/membrane housing. 3. Use a pliers, or heavy wire made into a hook, to pull the RO cartridge from the housing. Note: Sanitizing is recommended after servicing inner parts of the system (see page 9). 4. Install the new cartridge, end with o-ringseals inward. Work back and forth to get all the way in (end of cartridge about 1-1/4" in from end of housing). 5. Inspect the o-ring and collet. Replace if worn, cut or otherwise damaged. Carefully replace into the drain port. 6. Be sure the flow control is in the end of the tubing, then push all the way into the fitting. FIG, 10 ] TO DIqAIN 5. Lubricate the RO cap o-ringseal if dry. Replace the o-ring into the cap. Press inward on the cap while turning to the right ( ',)to lock. The cap will not go on if the RO cartridge is not fully seated inward. 6. Check the flow control and screen (see below). 7. Purge the RO membrane cartridge following instructions on page 9. FLOW CONTROL AND SCREEN :vl 114" tubing o-ring seal,al\'rain per1 low (control) insert SCreen The flow control is vital for proper operation of the RO membrane cartridge. The control keeps water flow through the membrane at the needed rate to obtain the best quality product water. Whenever servicing the RO system, check the flow control to be sure the small hole through it is clean and unrestricted. Also check and clean or replace the cone-shaped screen in front of the control. The RO membrane cannot discharge minerals and impurities to the drain if the flow control plugs with foreign material. If this happens, it only takes a short time for the membrane to foul and become useless. cap spring/ o-ring! /check bail valve To clean/replace flow control and screen (FIG. 10): 1. At the drain connection, depress the eollet (FIG. 11) with a finger while carefully pulling on the drain tubing to remove. 2. Remove the flow control from the end of the drain tubing. Be sure the center hole is clean. 3. Check the drain tubing to be sure it's clean. Then, insert the cleaned or new flow control into the tubing. 4. With a small screwdriver, carefully remove the collet and o-ring from the drain port. Use a small needle-nose pliers or tweezers to remove the screen from the drain port. Thoroughly clean, or replace with a new screen. Install, pointed end down. Note: Visually check to be sure it is positioned correctly. TUBING CONNECTION (all push-in fitting locations) This RO system includes push-in fittings for quick tubing connection at most locations. If working with the fittings, do the following. Connection (FIG. 11): 1. Use a sharp cutter or knife to cut the end of tubing square. 2. Inspect tl_e end (about 1") of the tubing to be sure there are no nicks, scratches or other rough spots. If needed, cut the tubing again. 3. Push tubing through the collet and all the way into fitting. Full engagement is 11/16" for 1 / 4" tubing, and 3/4" for 3/8" tubing. continued 12
13 - CARE OF YOUR REVERSE OSMOSIS SYSTEM - TUBING CONNECTION (continued) If tubing is used, other than supplied with the system, be sure it is of high quality, exact size and roundness with a smooth surface. AUTOMATIC SHUTOFF SERVICE If the shutoff assembly requires service, be sure to reassemble parts exactly as shown in FIG. 12, and to reconnect tubing as shown on pages 10 and 16. To Disconnect Tubing: Push the collet inward and hold with a finger while pulling the tubing out. Tubing correctly cut and connected FIG. 12 1/4" NPT x 3/8" ) Tube [ ToeFitt,n screw (4) cut tubing s_uare collet. i! end of tubing round and smooth, with no cuts, nicks or flat spats. " / Replacing collet and toilet (oepress to /.. / o-nng seal remove_blng_) / Push o-ring sealinto x4_,_ X / bottom of port, then [L.'_'_ / follow with collet tubing....-'%jdj..-j /.'. SHUTOFF ASSEMBLY diaphragm plunger O 7.--o.q_l, ng _co_let - ' Changing CoUet and O-ring (FIG. 11): diaphragm O 1. With a small screwdriver, remove tlie collet and o- ring from the fitting. 2. Be sure the port is clean, then lubricate and insert the o-ring seal to the bottom of the port. 3. Push the collet inward until it locks in place. r 1 I CAUTION I I DO NOT USE VINEGAR, OR OTHER ACID I I BASED CLEANERS ON THIS RO SYSTEM. THEY I I WILL DEGRADE SOME RO SYSTEM PARTS. AL- [ I WAYS USE SOAP AND WATER. ] L... J r--a,/ Elbowfittingturns into OUT port. Male Elbow, l/8" NPT x 1/4" Tubir tubing co!let /TPT Male Connector, x 1/4" Tube ] This reverse osmosis system contains a replaceable [ ] treatment component critical for effective removal ] ] of total dissolved solids. The water should be ] [ tested periodically to verify the system is perform- ] ] ing satisfactorily. I L... J 13
14 - CARE OF YOUR REVERSE OSMOSIS SYSTEM - REVERSE OSMOSIS SYSTEM CARE GUIDE MODEL Re AT LEAST every 6 months, replace the prefilter and postfilter cartridges. Clean or replace the flow control and screen. 2. Replace the RO membrane cartridge when the percent reiection of total dissolved solids (TDS) is less th an shown in the specifications (see B, below). If any of the following occur before the 6 months, replace as directed. A.SlowMakingofProductWater:Replacetheprefi]tercartridge. C.ChlorineTasteand/orOdor:Replacetheprefilter, postfilterand Iftheproductionratedoesnotimprove, replacethe postfilter car- Re membrane cartridges. tridge and Re membrane cartridge. B. High Total Dissolved Solids (TDS) in Product Water: Send treated and untreated water samples to a water analysis lab for testing.it isimportant retest boththe treated and untreated water I to determine system performance. If the TDS is not within the system's performance guidelines, replace the prefilter, postfilter and Re membrane cartridges. OTHER TROUBLESHOOTING PROBLEM CAUSE CORRECTION Chlorine taste and/or odor in the RO product water The ppm of chlorine in your water supply exceeds maximum limits, and has destroyed the Re membrane. The prefilter is no longer removing chlorine from the water supply. Ifthewater supply contains morethan 2.0 ppmof chlorine,additional filtering of the water supply to the RO is needed. Correct this condition before doing maintenance on the RO system, Replace the prefilter, postfilter and RO membrane cartridges, flow control, and screen. Other taste and/or odor Postfilter expended. RO membrane cartridge expended. Replace the postfilter cartridge, If taste and odor persists, replace the prefilter cartridge, RO membrane cartridge, flow control, and screen. Contaminationin productwaterstorage. Use sanitizing procedures. Replace the postfilter cartridge. System makes product WatersupplytotheROsystemnotwlthin Increasewaterpressure,preconditionthewater, etc.,asneeded water too slowly specifications, to conform before doing maintenance on the RO system. Prefilter or RO membrane cartridges Replacetheprefiltercartridge. lfratedoesnotincrease, replace plugged with sediments, the postfilter cartridge, RO membrane cartridge, flow control, and screen. System makes lower Storage tank air-charge less than 5-7 Open RO faucet and drain tank until flow slows to a drip. Keep amount of product water psi. faucet open and check tank pressure. If low, pressurize to 6 psi. than usual Close faucet to refill the tank. High total dissolved sol- WatersupplytotheROsystemnotwithin Increasewaterpressure,preconditionthewater, etc.,asneeded ids (TDS) in product wa- specifications, to conform before doing maintenance on the RO system. ter RO membrane cartridge expended. Replace the prefilter, postfilter and RO membrane cartridges, flow control, and screen. Water leaking from fau- Drain side of faucet airgap {3/8" tubing) Inspect and eliminate restriction or plug. Refer to installation cet airgap hole )lugged, restricted, or incorrectly con- instructions for proper drain connection. nected to drain point. Continual water flow to Checkvalveorautomaticshutoffassem- Clean, repair or replace as needed. drain bly plugged, restricted or parts worn Note: Sanitizing is recommended after servicing inner parts of the system(see page 9). 14
15 - DIMENSIONS and SPECIFICATIONS - 15" STORAGE TANK 9" dia. --_ Metric Supply water pressure limits psi Supply water temperature limits F kpa 5-40 C Maximum total dissolved solids (TDS) ppm Maximum water 6.9 ph gpg Maximum iron, manganese, hydrogen sulfide... 0 Chlorine in water supply (max. ppm) Supply water ph limits (ph) Product (quality) water, 24 hours (_... 6 gal. Waste water per gallon of product 5 gal. Percent rejection of TDS, minimum (new membrane) Storage tank capacity (max.) gal. Automatic shutoff control... yes 22.7 liters 18.9 liters 8.7 liters (_ feed water supply at 50 psi, 77 F, and 750 TDS - Quality water production, amount of waste water and percent rejection allvarywith changesin pressure,temperatureandtotaldissolved solids. 15
16 -REPAIR PARTS - WaterWorks Reverse Osmosis Drinking Water System, Model SADDLE VALVE See note on codes inthe statei of Massachusetts, page 5 '+ ij 32 1 I RO g J,, 1/4" Tubin o+ring seals DRAIN ADAPTER _/ 21 Bracket/Membrane Heusing PUSH - IN FI'FrlNGS (_)1/4" _3/8" o-ring seal 20 collet 24 _
17 - REPAIR PARTS - KEY NO WaterWorks T. PART NUMBER Faucet Reverse Osmosis Drinking Water S' tstem, Model RO 1000 DESCRIPTION Adaptor, 7/16"-24 Screw, #10-12 x 5/8" (8) R@ Membrane OF PART x 3/8" Tubing Cartridge O-ring Seal, 1-7/8" x 2-1/8" R@ Cap Elbow, 3/8" NPT x 3/8" Tube (2) Head (2) O-ring Seal, 3-3/8" x 3-5/8" (2) Filter Cart., T & O Postfilter Sump (2) Connector, 1/8" NPT x 1/4" Tubing Elbow, 1/8" NPT x 1/4" Tubing Valve Top Valve Center Plunger Diaphragm (2) Valve Bottom Screw, #10-14 x 1-3/4" (4 req.) Shutoff Assembly [] Tee, 1/4" NPT x 3/8 Tubing Elbow, 3/8" NPTx 1/4" Tube (2) Filter CarL, Sed.- T & O Prefilter KEYI PART NO.I NUMBER 23 I ! I ' !904170O ! ! DESCRIPTION Storage Tank Adaptor, Bracket/Membrane Check Ball Spring OF PART 1/4" NPT x 3/8" Tubing Housing O-ring Seal, 7/16" x 5/8" Check Valve Cap Cone Screen Flow (Control) Saddle Valve Drain Adapter Insert Push-in Fitting Kit, 1/4" _@ Push-in Fitting Kit, Screw (2) Hanger Washer (2) Sump Removal Wrench Tubing, 1/4" x 20' - white [] i Tubing, 1/4" x 100' - white Tubing, 3/8" x 29' - white Tubing, 3/8" x 100' - white [] Owners's Manual [] includes key numbers 14 through 19 [] tubing lengths for remote installations, page 18 (not included) Direct replacement for colored lengths of tubing. not see page 16 for use locations - Note: This o-ring and co]let are for replacement in the bracket/membrane housing only. They do not fit the other push-in fittings, key nos. 2, 7, 12, 13, 21 and not included 17
18 - REMOTE LOCATION FOR REVERSE OSMOSIS SYSTEM - REMOTE RO INSTALLATION (storage tank not shown) Possible remote locations for the RO nearby the kitchen or bathroom sink include; (1) a basement area underneath the sink, and (2) an adjacent room or closet. Longer lengths of tubing may be needed (see parts list on page 17). You can run the drain tubing directly to 1 of several suitable open drain points, as shown below, bypassing the faucet airgap and p-trap d rain. This type of drain is the preferred over the p-trap drain adapter. Check your local codes. Always be sure to provide an air gap between the end of the hose and the drain point. RO product water faucet 3/8" blue tubing Note: Tubing colors as supplied with RQ system. OPTIONAL DRAIN POINTS FOR REJECT WATER red ( red storage tank COLD WATER SUPPLY airgap / STANDPIPE LAUNDRY TUB FLOOR DRAIN When ordering parts, always provide the following information: Product Type: WaterWorks TM Reverse Osmosis Drinking Water System Model: RO 1000 Part Number: from page 17 Part Description: from page 17 For the repair or replacement parts you need Call 7 am - 7 pro, 7 days aweek PART ( ) 18
19 19
20 20
ERO-175. Undersink REVERSE OSMOSIS DRINKING WATER SYSTEM. u Safety Guides u Installation u Operation u Maintenance u Repair Parts
Undersink REVERSE OSMOSIS DRINKING WATER SYSTEM ERO-175 u Safety Guides u Installation u Operation u Maintenance u Repair Parts EcoWater Systems LLC P.O. Box 64420 St. Paul, MN 55164 TEL (651) 739-5330
More informationInstallation and Operation Manual
Model EP-RO25 How to install, operate and maintain your Reverse Osmosis Drinking Water System Do not return unit to store If you have any questions or concerns when installing, operating or maintaining
More informationNSRO42C4. How to Install, operate and maintain your Reverse Osmosis Drinking Water System
NSRO42C4 How to Install, operate and maintain your Reverse Osmosis Drinking Water System If you have any questions or concerns when installing, operating or maintaining your Reverse Osmosis System call
More informationERO-375E. Undersink REVERSE OSMOSIS DRINKING WATER SYSTEM. Safety Guides Installation Operation Maintenance Repair Parts
Undersink REVERSE OSMOSIS DRINKING WATER SYSTEM ERO-375E Safety Guides Installation Operation Maintenance Repair Parts System tested and certified by NSF International against NSF/ANSI Standard 58. See
More informationPRF-RO Pentair Reverse Osmosis System Installation and Maintenance Manual SAFETY GUIDES THE BASIC REVERSE OSMOSIS SYSTEM. Tools and Materials Required
PRF-RO Pentair Reverse Osmosis System Installation and Maintenance Manual SAFETY GUIDES Read and follow all steps and guides carefully before installing and using your reverse osmosis system. Do not use
More informationAdvanced Two-Stage Drinking Water Filter
OWNER'S MANUAL E L I T E Advanced Two-Stage Drinking Water Filter MODEL NO. 625.385010 Caution: Read and follow all safety rules and operating instructions before first use of this product. Questions?
More informationGROWMAX WATER Perfect Water for Plants and Gardens
GROWMAX WATER Perfect Water for Plants and Gardens WATER SYSTEMS FOR HYDROPONICS AND GARDENING GROWMAX 3000 Ultra-Pure Reverse Osmosis Water System Up to 3000 L/D of Pure Water Don't forget to register
More informationMKTF CRO-Series 5-Stage Reverse Osmosis System Installation and Maintenance Manual
MKTF - 215 CRO-Series 5-Stage Reverse Osmosis System Installation and Maintenance Manual Please fill out the following information at the time of installation. Save for future reference. Model: Date Code:
More informationSystem tested and certified by NSF International against NSF/ANSI Standard 42. See performance data sheet for details, Printed on recycled
OWNER'S MANUAL Undersink Housing System ;r Filter MODEL NO. 625.384540 Caution: Read and follow all safety rules and operating instructions before first use of this product. Questions? Visit www.kenmorewater.com
More informationInstallation & Service Guide
Reverse Osmosis Ontario Soft Water.ca Kitchener, Canada 519-579-0500 Installation & Service Guide Pentair 75 gpd Encapsulated Membrane System Standard System 75gpd Membrane Your New Reverse Osmosis System
More information475 PRO SERIES Reverse Osmosis System Installation & Operation Manual
PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THIS SYSTEM 475 PRO SERIES Reverse Osmosis System Installation & Operation Manual Model STAGE 1 STAGE 2 STAGE 3 STAGE 4 OUTPUT 475 SEDIMENT CARBON
More informationInstallation and Operation Manual
How To Install, Operate and Maintain Your Reverse Osmosis System FILTER CARTRIDGE CONFIGURATION MAY BE SUBJECT TO CHANGE. 475 PRO SERIES 475BP PRO SERIES INSTALLERS: PLEASE READ ALL INSTRUCTIONS BEFORE
More informationInstallation and Operation Manual
How To Install, Operate and Maintain Your Reverse Osmosis System INSTALLERS: PLEASE READ ALL INSTRUCTIONS BEFORE IN- STALLING AND USING THIS SYSTEM. IT IS RECOMMENDED TO WAIT UNTIL THE ENTIRE SYSTEM IS
More informationReverse Osmosis Drinking Water System
OWNER'S MANUAL MODEL NO. UltraFilter 150 625.385700 UltraFilter 350 625.385720 Caution: Read and Follow All Safety Rules and Operating Instructions Before First Use of This Product. If you have questions
More informationOwner s Manual AQ-RO-BASE. Aquasana OptimH2O Drinking Water System Reverse Osmosis Filtration Technology
Owner s Manual AQ-RO-BASE Aquasana Drinking Water System Reverse Osmosis Filtration Technology Welcome to the Aquasana experience. You are about to enjoy clean, clear water and the peace of mind that comes
More informationReverse Osmosis Drinking Water System OWNER'S MANUAL MODEL NO
OWNER'S MANUAL MODEL NO. 625.384700 Caution: Read and Follow All Safety Rules and Operating nstructions Before First Use of This Product. Reverse Osmosis Drinking Water System Warranty How To nstall f
More informationAPEX Water Filters MODEL RO 5. Treat your body to pure goodness with Apex filtered water INSTRUCTION MANUAL. pure water in every drop
APEX Water Filters pure water in every drop MODEL RO 5 INSTRUCTION MANUAL Treat your body to pure goodness with Apex filtered water A Water supply adapter valve B Cold water shut-off valve C Hot water
More informationModel WHER12. Model WriER18. How to install, operate maintain your Reverse Drinking Water System. Do not return R.O. to store
TM Model WHER12 Model WriER18 How to install, operate maintain your Reverse Drinking Water System and Osmosis Do not return R.O. to store If you have questions or concerns when installing, operating or
More informationWATER FILTRATION SYSTEM (USF3) OWNER S MANUAL
WATER FILTRATION SYSTEM (USF3) OWNER S MANUAL 1 INTRODUCTION Congratulations on choosing Permatech to improve the quality of your water. You will immediately begin to notice the numerous benefits of having
More informationOWNER S MANUAL. How to install, operate and maintain your. EcoWater Systems Automatic Sediment Filter
OWNER S MANUAL How to install, operate and maintain your EcoWater Systems Automatic Sediment Filter Model EASF1 EcoWater Systems LLC P.O. Box 64420, St. Paul, MN 55164-0420 7301805 (Rev. C 8/26/08) Table
More informationPRO-RO 6-Stage Reverse Osmosis System
PRO-RO 6-Stage Reverse Osmosis System Rev: 1016 Introduction to the PRO-RO Congratulations on your purchase of the PRO-RO six stage reverse osmosis system. The PRO-RO features a four-stage prefilter,
More informationULTIMATE REVERSE OSMOSIS SYSTEM
ULTIMATE REVERSE OSMOSIS SYSTEM INSTALLATION INSTRUCTION & OWNER S MANUAL Ver 3.1 All Rights Reserved APEC Water Systems Please keep this Owner s Manual for future reference. It contains useful information
More informationREVERSE OSMOSIS WATER FILTRATION SYSTEM MODEL PB-TLRO4H50T INSTRUCTION MANUAL
REVERSE OSMOSIS WATER FILTRATION SYSTEM MODEL PB-TLRO4H50T INSTRUCTION MANUAL Pure Blue H20, LLC 13813 Monroes Business Park Tampa, FL 33635 USA www.pureblueh2o.com (844) 787-3148 (844) PURE-1-4-U 2015.02.25
More informationOwner s Manual AQ-RO-3. Aquasana OptimH2O Drinking Water System. Reverse Osmosis plus Claryum Filtration Technology
Owner s Manual AQ-RO-3 Aquasana OptimHO Drinking Water System Reverse Osmosis plus Claryum Filtration Technology Welcome to the Aquasana experience. You are about to enjoy clean, clear water and the peace
More informationOWNER S MANUAL AND INSTALLATION GUIDE PLEASE READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING INSTALLATION
ClearChoice Economy Under Sink Drinking Water System OWNER S MANUAL AND INSTALLATION GUIDE PLEASE READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING INSTALLATION Congratulations on the purchase of your ClearChoice
More informationOWNER S MANUAL. How to install, operate and maintain your. EcoWater Systems Automatic Sediment Filter. EcoWater Systems Poland
OWNER S MANUAL How to install, operate and maintain your EcoWater Systems Automatic Sediment Filter Model AFF EcoWater Systems Poland Bałtycka 6, 61-013 Poznań, Poland www.ecowater-systems.com 201-8402972
More informationWATER FILTRATION SYSTEM (RO6) OWNER S MANUAL
WATER FILTRATION SYSTEM (RO6) OWNER S MANUAL 1 INTRODUCTION Congratulations on choosing Permatech to improve the quality of your water. You will immediately notice the numerous benefits of having quality
More informationTap Master Artesian Hydro Gardener Series Installation & Service Manual
Perfect Water Technologies 7 Tips for an Easy and Successful Installation 1. Keep it simple - there are 3 connections to make, and the tubing is color coded. 2. Have plenty of time, light, space, and towels
More informationInstallation and Operation Manual
Model EP-ASF1 How to install, operate and maintain your Automatic Sediment Filter If you have any questions or concerns when installing, operating or maintaining your Automatic Sediment Filter, call our
More informationInstallation and Operation Manual
Installation and Operation Manual Canature North America Inc. How To Install, Operate and Maintain Your Reverse Osmosis System FILTER CARTRIDGE CONFIGURATION MAY BE SUBJECT TO CHANGE. 475 PRO SERIES 475BP
More informationWATER FILTRATION SYSTEM (RO5) OWNER S MANUAL
WATER FILTRATION SYSTEM (RO5) OWNER S MANUAL 1 INTRODUCTION Congratulations on choosing Permatech to improve the quality of your water. You will immediately notice the numerous benefits of having quality
More informationSears, Roebuck and Co., Chicago, IL U.S.A.
BLENDING TANK WARRANTY... PG 2 DIMENSIONS-SPECIFICATIONS.PG 2 OPERATION... PG 3 INSTALLING... PG 3 MAINTENANCE... PG 5 REPAIR PARTS... PG 5 Sears, Roebuck and Co., Chicago, IL 60684 U.S.A. BLENDING TANK
More informationParasitic Cysts - Cryptosporidium and Giardia, Chemicals, Heavy Metals, Dissolved Salts, Offensive Tastes and Odours, Sediment, Dirt,
Aqua-Pure is a market leader in water filtration. In addition to our comprehensive range of Domestic Water Purifiers, we design and manufacture an extensive commercial and industrial range of purification
More information5-Stage Reverse Osmosis System
5-Stage Reverse Osmosis System 41840 McAlby Court, Suite A Murrieta, CA 92562 800-451-9343, FAX 951-894-2801 www.nimbuswater.com 02/09 1 Introduction to the WaterMaker Five Congratulations on your purchase
More informationERO-375 HERO-375. Undersink REVERSE OSMOSIS DRINKING WATER SYSTEM. Safety Guides Installation Operation Maintenance Repair Parts
Undersink REVERSE OSMOSIS DRINKING WATER SYSTEM ERO-375 HERO-375 Safety Guides Installation Operation Maintenance Repair Parts System tested and certified by NSF International against NSF/ANSI Standard
More informationR.O. DRINKING WATER SYSTEM
R.O. DRINKING WATER SYSTEM INSTALLATION, OPERATION & SERVICE MANUAL IMPORTANT NOTICES: This reverse osmosis system contains replaceable treatment components critical for effective performance. It is the
More informationReverse Osmosis System OWNERS MANUAL
APS Water Services Corporation Quick Change, Twist & Loc Reverse Osmosis System OWNERS MANUAL Installation, Operation & Maintenance Sold By : APS Water Services Corp 818-786-0600 NOTE: Please read through
More informationREVERSE OSMOSIS DRINKING WATER SYSTEM
REVERSE OSMOSIS DRINKING WATER SYSTEM 10/10 1 2 Introduction To The Sierra Congratulations on your purchase of the Nimbus Sierra reverse osmosis system. When properly maintained, this system will provide
More informationTANKLESS REVERSE OSMOSIS SYSTEMS USER S MANUAL
Water Systems, LLC www.123filter.com Email: sales@123filter.com TANKLESS REVERSE OSMOSIS SYSTEMS USER S MANUAL Model #RCB4T ABOUT THE SYSTEM Reverse Osmosis process is a separation process. Tap water enters
More informationUS Water American Revolution 5-Stage RO System The ONLY RO system on the market that is totally American made!
US Water American Revolution 5-Stage RO System The ONLY RO system on the market that is totally American made! MEMBRANE POST CARBON PRE SEDIMENT TUBING FAUCET AND MOUNTING KIT FILTER WRENCH DRAIN SADDLE
More informationAlkaline RO System INSTALLATION MANUAL
Alkaline RO System INSTALLATION MANUAL 1-800-992-8876 Customer Support Disclaimer All rights reserved. All material published on this site by Express Water Inc., including all portions of the website,
More informationReverse Osmosis System
OWNER'S MANUAL Reverse Osmosis System MODEL NO. 625.381560 UltraFilter 450 Caution: Read and follow aft safety rules and operating instructions before first use of this product. Questions? Visit www.kenmorewater.com
More informationSystem tested and certified by NSF International against NSF/ANSl Standard 42 and 58. See performance data sheet for details, Printed on recycled
OWNER'S MANUAL O E L I T Reverse Osmosis System I Z _D _m R D MODEL NO. 625.385560 UltraFilter 650 m i D _W _D O Caution: Read and follow all safety rules and operating instructions before first use of
More informationWATERSHIELIJrM REVERSE OSMOSIS INSTALLA TION MANUAL ~ ~ ~ ~ ~ l ~ TO INSURE THIS PRODUCT AND THE INSTALLATION THEREOF. ~ ~ ~ ~ ~
WATERSHIELIJrM REVERSE OSMOSIS SYSTEM INSTALLA TION MANUAL p 1 ~ -~ I IMPORTANT I ITHIS REVERSE OSMOSIS SYSTEM WAS SOLD IN KIT FORM. IT HAS ~ INOT BEEN PRESSURE TESTED IN ANY WAY. UPON INSTALLATION IT
More informationRO.. DRINKING WATER SYSTEM
MICROLINE RO.. DRINKING WATER SYSTEM MODEL C. T. A. - 3 INSTALLATION, OPERATION & SERVICE MANUAL IMPORTANT NOTICES: This reverse osmosis system contains replaceable treatment components critical for effective
More informationTable of Contents. List of Figures
1 P a g e Table of Contents Introduction. 3 Receiving....4 Description Model G3 & G4...5/6 Water Production Flow Chart...7 Positioning the Cooler...8 Water Cooler Connections..9 Feed Water Connection....10
More informationMODEL NO {DELUXE) WaterWorks. Safety Guides Installation Operation Cartridge Replacement Repair Parts
MODEL NO. 625.343800 625.343820 {DELUXE) Caution: Read and Follow All Safety Rules, Installation and Operating Instructions Before First Use of This Product. WaterWorks If you have questions when installing
More information1 P a g e. G4 Counter Top OPERATION MANUAL
1 P a g e G4 Counter Top OPERATION MANUAL Table of Contents Introduction. 3 Receiving....4 Description Model G3 & G4...5/6 Water Production Flow Chart...7 Positioning the Cooler...8 Water Cooler Connections..9
More informationREVERSE OSMOSIS DRINKING WATER SYSTEM
REVERSE OSMOSIS DRINKING WATER SYSTEM INSTALLATION, OPERATION & SERVICE MANUAL Drink With Confidence! TABLE OF CONTENTS SECTION I. Page INTRODUCTION...3 SECTION II. SPECIFICATIONS...4 SECTION III. SECTION
More informationINSTALLATION MANUAL CRS-3
INSTALLATION MANUAL CRS-3 12630 US 33 N. Churubusco, IN 46723 Ph. (260)693-1972 Fax (260)693-0602 www.sterlingwatertreatment.com 1 TABLE OF CONTENTS: SECTION I. SECTION II. INTRODUCTION...3 SPECIFICATIONS...3
More informationModel #: PT3000T36-GOLD
Good Water Warehouse Inc. 1700 E Walnut Ave Fullerton CA 92831 (714) 441-2893 (714) 441-0525 FAX Reverse Osmosis System Installation & Service Guide Model #: PT3000T36-GOLD Do not use with water that is
More informationPremier Reverse Osmosis Drinking Water System
OWNER'S MANUAL 0 Premier Reverse Osmosis Drinking Water System _W _O _o _m _m l o MODEL NO. 625.385560 0 Caution: Read and follow all safety rules and operating instructions before first use of this product.
More informationIMPORTANT! ank You! Model: Twist-In 100 GPD, 3-Stage RO Unit. Installation, Operation & Maintenance Guide
Twist-In 00 GPD, 3-Stage RO Unit WARNING: Please read carefully before proceeding with installation. Your failure to follow any attached instructions and operating parameters may lead to the product s
More informationINSTALLATION & SERVICE MANUAL
INSTALLATION & SERVICE MANUAL Countertop Reverse Osmosis Systems Series CT System Tested and Certified by WQA against NSF/ANSI Standard 58 for the reduction of Arsenic, Barium, Cadmium, Copper, Cyst, Hexavalent
More informationInstallation Instructions. For the 18 Built-In Dishwasher and Front Color Panels
Installation Instructions For the 18 Built-In Dishwasher and Front Color Panels Printed in USA 154232102 Before You Begin DO NOT INSTALL DISHWASHER UNTIL YOU HAVE READ ALL INSTRUCTIONS. FOR YOUR SAFETY,
More informationispring Whole House Water Filter Systems USER S MANUAL
ispring Whole House Water Filter Systems USER S MANUAL Version 2014-5 Introduction Congratulations on your purchase of the ispring Whole House Water Filter system. Featuring a three-stage filtration process,
More informationREVERSE OSMOSIS DRINKING WATER SYSTEM
REVERSE OSMOSIS DRINKING WATER SYSTEM 12/12 1 Please fill out the following information at the time of installation. Save for future reference. Model: Sierra NS-1N30-00 Date Code: Install Date: Sold by:
More informationby Water Purification Supplies
REVERSE OSMOSIS PURIFIER With Booster Pump by Water Purification Supplies Member, Water Quality Association Read these instructions carefully before using the purifier. Retain these instructions in safe
More informationINSTALLATION & SERVICE MANUAL
INSTALLATION & SERVICE MANUAL Countertop Reverse Osmosis Systems Series CT CT-315 CT-315TFC CT-445 CT-445P CT-D425 CT-D425P CT-550UP 3 STAGE CTA RO SYSTEM 3 STAGE TFC RO SYSTEM 4 STAGE TFC RO SYSTEM 4
More informationInstallation Instructions Residential Reverse Osmosis Drinking Water System
Your Reverse Osmosis System has been tested to ensure it will operate correctly. The following periodic maintenance is recommended so your system will provide years of trouble-free service: Replacement
More informationWM-450-PT WM-900-PT Commercial Wall Mounted Reverse Osmosis
WM-450-PT WM-900-PT Commercial Wall Mounted Reverse Osmosis Installation And Service Manual Watts Pure Water 1725 W. Williams Dr. C-20., Phoenix, Arizona 85027 Phone: 888-774-7405 Fax: 602-588-0356 www.wattspurewater.com
More informationREVERSE OSMOSIS DRINKING WATER SYSTEM
REVERSE OSMOSIS DRINKING WATER SYSTEM Model RO-14C Installation, Operation & Service Manual This system has been tested under Industry Standard S-300-91 for TDS reduction and structural integrity. TABLE
More informationInstallation Instructions
Installation Instructions For the 18" Built-In Dishwasher Sears, Roebuck and Co. Sears Canada, Inc. Hoffman Estates, IL 60179 U.S.A. Toronto, Ontario, Canada M5B 2B8 154435201 Before You Begin DO NOT INSTALL
More informationInstallation Instructions
Installation Instructions SELECTRONIC Hard-Wired AC Powered ICU Lavatory Proximity Faucet PRODUCT NUMBER 0. Certified to comply with ASME A..M 0 American Standard M 0. ICU Faucet shown Installed on American
More informationINSTALLATION MANUAL ARS-1
INSTALLATION MANUAL ARS-1 First Sales, LLC 12630 US 33 N. Churubusco, IN 46723 Ph. (260) 693-1972 Fax (260) 693-0602 1 ARS-1 Manual 141021 TABLE OF CONTENTS: SECTION I. SECTION II. INTRODUCTION AND LIABILITY...3
More informationDWSB-TFC-50 DWSB-50-PUMP
INSTALLATION MANUAL DWSB-TFC-50 DWSB-50-PUMP 12630 US 33 N. Churubusco, IN 46723 Ph. (260)693-1972 Fax (260)693-0602 www.sterlingwatertreatment.com 1 TABLE OF CONTENTS: SECTION I. SECTION II. INTRODUCTION...3
More informationTABLE OF CONTENT WARNING: READ ENTIRE MANUAL. FAILURE TO FOLLOW ALL GUIDES AND RULES COULD CAUSE PERSONAL INJURY OR PROPERTY DAMAGE.
TABLE OF CONTENT I. COMPONENTS AND TOOLS IDENTIFICATION... 3 II. PRE-INSTALLATION... 3 System Location... 4 Site Preparation... 4 Unit Preparation... 4 III. INSTALLATION INSTRUCTIONS... 4 Faucet Installation...
More informationClean Water Made Easy. CWS Time Clock Softener Installation & Start Up Guide. Questions?
Clean Water Made Easy www.cleanwaterstore.com CWS Time Clock Softener Installation & Start Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
More informationTop Control Dishwasher
INSTALLATION GUIDE Top Control Dishwasher NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Before using your new product, please read these instructions to prevent any damage. Contents Introduction......................................................................................................
More informationINSTALLATION AND OPERATIONS MANUAL
MODEL 6001 REVERSE OSMOSIS High Purity Water Production System THREE STAGE Filtration for the reduction of: Organic Matter Total Dissolved Solids (TDS) Suspended Solids Chemical Contaminants Bad Taste
More informationClean Water Made Easy
Clean Water Made Easy http://www.cleanwaterstore.com Pro-OX 2510 Iron Filter Installation & Start- Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine
More informationInstallation Instructions for:
Installation Instructions for: Home II Reverse Osmosis System Home II Reverse Osmosis System COMBO Installation Instructions Pre-amble. This Aquasafe Reverse Osmosis System has been specifically designed
More informationTier1 Water Home Filtration System
Tier1 Water Home Filtration System Salt-Free Softener OWNERS MANUAL BEFORE YOU BEGIN INSTALLATION, READ THIS ENTIRE MANUAL. FOLLOW THE INSTALLATION INSTRUCTIONS CAREFULLY. 1. Avoid pinched o-rings during
More informationINSTALLATION, OPERATION AND SERVICE MANUAL GUARDIAN R.O. DRINKING WATER SYSTEM WITH WATER QUALITY MONITOR MODEL LRO-35
INSTALLATION, OPERATION AND SERVICE MANUAL GUARDIAN R.O. DRINKING WATER SYSTEM WITH WATER QUALITY MONITOR MODEL LRO-35 Tested and Certified by NSF International against NSF/ANSI Standard 58 for the reduction
More informationPlease read the following installation instructions first after purchasing this product or transporting it to another location.
9 Installation Overview Please read the following installation instructions first after purchasing this product or transporting it to another location. 1 Unpacking your refrigerator 2 Choosing the proper
More informationInstalling the Turbo Floor Model System
Installing the Turbo Floor Model System Location 1. Locate as close as possible to water supply source. 2. Locate as close as possible to a three-prong grounding receptacle. 3. Locate the System on a smooth
More informationMODEL FW-2000 OPERATION MANUAL
MODEL FW-2000 OPERATION MANUAL 1 P a g e Table of Contents Introduction...pg.3 Receiving..pg.4 Description Model H2O- 2000....pg.5 Operation. pg.6,7 Drain Container Operation. p.g.8 Cup Dispenser Operation.p.g.9
More informationWM Stage Reverse Osmosis System
WM5-50 5-Stage Reverse Osmosis System System tested and certified by NSF International against NSF/ANSI Standard 58 for the reduction of substances specified on the performance data sheet. 41840 McAlby
More informationIMPORTANT! ank You! Model: Twist-In 100 GPD 4-Stage RO/DI Unit. Installation, Operation & Maintenance Guide
Model: 54037 Twist-In 00 GPD 4-Stage RO/DI Unit WARNING: Please read carefully before proceeding with installation. Your failure to follow any attached instructions and operating parameters may lead to
More informationInstant Hot Water Dispenser Owner s Manual
Model Hot1 Instant Hot Water Dispenser Owner s Manual Installation, Care & Use Instalacion, cuidado & uso Installation, soin et utilisation WHAT YOU SHOULD KNOW BEFORE YOU BEGIN For your satisfaction and
More informationInstallation Instructions
Installation Instructions Built-In Dishwasher If you have questions, call 800-944-9400(US),800-245-8352(Canada)or visit our website at: www.frigidaire.com BEFORE YOU BEGIN Read these instructions completely
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILT-IN BOTTOM MOUNT REFRIGERATOR/FREEZER DBRTGK72SS-GRILLE KIT (FOR designer SERIES ONLY) VIKING RANGE CORPORATION 111 Front Street Greenwood, Mississippi (MS) 38930 USA (662)
More informationReverse Osmosis Filter Change Guide
Reverse Osmosis Filter Change Guide Written by 602abcWATER Start Here Con irm Your ilter order. Open your packages and confirm that you have received all the correct filters. If you are missing or sent
More informationOwners Manual. Economy RO. Installation, Operation & Service Instructions with Parts List Economy Reverse Osmosis Drinking Water System
Owners Manual Economy RO Installation, Operation & Service Instructions with Parts List Economy Reverse Osmosis Drinking Water System Models: RO75, RO75BP Canada West 855 Park St., Unit 1 Regina, SK S4N
More informationDishwasher Installation Instructions DW 24XT/DW 24XV
Dishwasher Installation Instructions DW 24XT/DW 24XV Installation Instructions Dishwasher BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT Observe all governing codes and ordinances.
More informationInstallation, Operation & Service Instructions with Part List. Quick Change Reverse Osmosis Drinking Water System
Installation, Operation & Service Instructions with Part List Quick Change Reverse Osmosis Drinking Water System Model No. QCRO4V-50 www.pura.com This system certified by WQA according to NSF/ANSI 58 for
More informationFleck 2510 SXT Catalox Installation & Start Up Guide
Fleck 2510 SXT Catalox Installation & Start Up Guide For Catalox Filters with PotPerm Bleach Solution Tank Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
More informationUser Guide Reverse Osmosis Undersink Water Filter Systems RO SERIES
User Guide Reverse Osmosis Undersink Water Filter Systems RO SERIES For correct operation & installation it is essential to observe these instructions. What's Inside What s inside Introduction...3 Operation...3
More informationClean Water Made Easy
Clean Water Made Easy http://www.cleanwaterstore.com Pro-OX 1650 Iron Filter Installation & Start-Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
More informationInstallation Instructions for:
Installation Instructions for: Maximus II Reverse Osmosis System with Remineralization Maximus II Reverse Osmosis System COMBO with Remineralization Installation Instructions Pre-amble. This Aquasafe Reverse
More informationTier1 Water Home Filtration System
Tier1 Water Home Filtration System Carbon+KDF Series OWNERS MANUAL BEFORE YOU BEGIN INSTALLATION, READ THIS ENTIRE MANUAL. FOLLOW THE INSTALLATION INSTRUCTIONS CAREFULLY. 1. Avoid pinched o-rings during
More informationModel MRO-35 INSTALLATION, OPERATION & SERVICE MANUAL
Millennium Reverse Osmosis Drinking Water System Model MRO-35 INSTALLATION, OPERATION & SERVICE MANUAL Tested and Certified by NSF International against NSF/ANSI Standard 58 for the reduction of the claims
More information1 P a g e MODEL G5CT COUNTER TOP OPERATION MANUAL
1 P a g e MODEL G5CT COUNTER TOP OPERATION MANUAL Table of Contents Introduction...pg.3 Receiving..pg.4 Description Model G5CT Counter Top.......pg.5 Operation. pg.6,7 Positioning the Cooler....pg.8 Water
More informationReverse Osmosis Drinking Water System
OWNER'S MANUAL MODEL NO. UltraFilter 550 625.385750 Caution: Read and Follow All Safety Rules and Operating nstructions Before First Use of This Product. f you have questions when installing, operating
More informationHot-1 Hot Water Dispenser
The Installation, Care and Use of Your New Hot-1 Hot Water Dispenser Valve lever design may vary How your hot water dispenser works Water is electrically heated to a brewing/cooking hot 190 F (88 C)* by
More informationFleck 5600 Carbon Filter Installation & Start Up Guide
Clean Water Made Easy www.cleanwaterstore.com Fleck 5600 Carbon Filter Installation & Start Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
More informationInstallation Instructions Built-In Dishwasher
GE Consumer & Industrial Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com BEFORE YOU BEGIN Read these
More informationAQUA ONE. Reverse Osmosis System Model ARO5000. Installation and Service Guide PLEASE READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING INSTALLATION
AQUA ONE Reverse Osmosis System Model ARO5000 Congratulations on your purchase of the most sophisticated water purifier system available! Installation and Service Guide PLEASE READ THIS MANUAL CAREFULLY
More informationInstallation Instructions
GE Consumer & Industrial Appliances Installation Instructions Junction Box Cover Within this user bag, you will find a junction box cover and a #10 hex head screw used to attach the junction box cover
More informationGE & PROFILE SmartWater Softener Systems
GE & PROFILE SmartWater Softener Systems INSTALLATION INSTRUCTIONS GE Models GNSF18Z01, GNSF2Z01, GNSF5Z01, GXSF2Z01 & Profile Model PNSF1Z01 TABLE OF CONTENTS: Page # Important Installation Recommendations
More information