Installation Instructions WARNING WARNING. Variable Speed High Efficiency Blower Kit for Gas Furnace Applications 3. INSTALLATION

Size: px
Start display at page:

Download "Installation Instructions WARNING WARNING. Variable Speed High Efficiency Blower Kit for Gas Furnace Applications 3. INSTALLATION"

Transcription

1 Installation Instructions Variable Speed High Efficiency Blower Kit for Gas Furnace Applications ANING To avoid the risk of electrical shock, personal injury, or death, disconnect electrical power before installing this kit or performing maintenance. Before beginning installation, read these instructions thoroughly and follow all warnings and cautions in these instructions and on the unit. These instructions are primarily intended to assist qualifi ed individuals experienced in the proper installation of this appliance. Some local codes require licensed installation/service personnel for this type of equipment. Improper installation, service, adjustment, of maintenance can cause fi re, electrical shock of other conditions which may result in personal injury or property damage, unless otherwise noted in the instructions, only factory authorized kits of accessories may be used when modifying this product.. SPEIFIATIONS The variable speed blower kit is designed for installation in G7 gas furnaces. Part number 9087 is for A cabinet models and may be fi eld-confi gured for air conditioning/ heat pump airfl ows from -/ to tons. Part number is for B cabinet models and may be fi eld-confi gured for air conditioning/heat pump airfl ows from to -/ tons. Part number is for cabinet models, and may be field-configured for air conditioning/heat pump airfl ows from to tons. Part number is for D cabinet models and may be fi eld-confi gured for air conditioning/heat pump airfl ows from to tons. Part number is an upgrade kit for units already equipped with the Fixed Speed High Effi ciency Blower. Note: hen using these kits as part of an iq Drive System, replace the transformer in the furnace with a 0 VA transformer - NODYNE part number 07 (see iq Drive instructions).. INSTALLATION EQUIEMENTS heck Equipment After unpacking, inspect the kit thoroughly for concealed damage. If damage is found, notify the transportation company immediately and fi le a concealed damage claim. All installations shall be made as described in the installation instructions and in accordance with applicable national and local codes including the requirements of local utilities.. INSTALLATION G7 VSHE Blower Kit - SKUs 9087, 90877, 90878, Loose harness descriptions: For upflow furnaces: A7 or 99 Female 9-pin AMP mate-n-lok to -pin power connector, blue wire with female Q, black wire with female Q, and white wire with female Q For downflow furnace: 77 Female 9-pin AMP mate-n-lok to female 8-pin JST connector, blue wires with female Q, black wire with female Q, and white wire with female Q 70 Male 9-pin AMP mate-n-lok to female 8-pin JST connector, blue wires with female Q, black wire with male Q, and white wire with male Q A0 or 70 -pin power connector to -pin power connector Upflow Installations. Disconnect electrical power to the furnace.. emove the upper and lower access doors from the furnace.. emove or back-out the ground screws from the top of the blower deck to allow the blower to slide out of the furnace.. Unplug the existing electrical connector containing the blower wires from the receptacle located on the right side of the blower deck.. emove the blower assembly from the furnace by removing the screws attaching the blower to the blower deck and sliding the blower assembly out of the furnace.. emove the existing upper wire harness containing the blower power wires from the blower deck and the furnace control board, including the wires in the harness which go to the limits (supply air limit and either the vent limit, on select models, or the fl ame roll-out limit). ANING Failure to remove the existing high voltage harness in this step may damage new motor or control board if VSHE kit is connected. 7. Also remove the other blue limit wire from the supply air limit, cut off the connector, wire nut the blue wire (from pin 8 of the furnace control board 9-pin control harness), and leave dead.

2

3 8. If needed, attach the blower mounting brackets to the blower assembly. These brackets may be already attached to the new blower, or they may be taken from the old blower. 9. Slide the blower assembly into the furnace. Be sure that the sides of the blower are captured by all of the blower mounting tabs in the blower deck. Secure with the screws removed in step. 0. eplace the ground screws attaching the ground wires to the blower deck removed in step.. Install the A7 or 99 wire harness (loose harness included in kit). Attach the female 9-pin AMP panel connector to the blower deck. Attach the -pin power connector to the Expansion Port connector on the furnace control board. Attach the black wire to LA on the furnace control board. Attach the white wire to an open Neutral on the furnace control board. Attach the limit wire to the supply air limit (terminal open from step 7).. Install the blue jumper wire (included in kit) from the supply air limit to the fl ame roll-out limit or, on select models, the vent limit (open terminals from step ).. Attach the electrical plug of the new blower assembly to the receptacle installed in the blower deck in step.. Verify all wires are connected to the furnace according to the wiring diagram. Additionally, verify all wires which are factory connected and tighten as necessary.. Use wire ties to secure wires away from moving parts, burner area, and to keep wires neat.. efer to section marked onfi guring the Blower. If necessary to gain access to the motor control board, remove the cover of the motor control board mounting bracket. eplace when fi nished confi guring the blower. 7. eplace current wiring diagram with new wiring diagram for the application which is included in the kit. 8. eplace doors. estore power to the furnace. Installation is now complete. Downflow Installations For downfl ow installations, the motor control board and power choke (applicable with ¾ and hp motors) will be mounted separately from the blower. Begin installation by preparing the blower kit as follows: emove the wiring harness which was pre-installed on the kit, the motor control board, and the choke (if applicable) from the motor control mounting bracket, disconnecting any wiring to allow these parts to be removed. emove the motor control mounting bracket by removing the screws attaching it to the blower. Install the new 70 wiring harness (loose harness included in kit) by attaching the 8-pin female connector to the motor low voltage 8-pin plug. Attach the black wire to the motor black power wire, and the white wire to the motor white power wire. Attach the longer of the blue limit wires to the limit on the opposite side of the blower wrapper, and the shorter blue limit wire to the limit on the same side of the blower wrapper as the motor. Leave the blue jumper wire attaching the blower limits on either side of the blower housing. Be sure to reattach the green motor ground wire to the blower wrapper side. If applicable, remove the blower mounting brackets from either side of the blower housing.. Disconnect electrical power to the furnace.. emove the upper and lower access doors from the furnace.. emove the fl ue pipe from in front of the inner blower access door.. emove the inner blower access door and unplug the receptacle containing the blower wires from the blower access door support column.. emove the screws securing the blower assembly and slide the entire blower assembly out of the furnace.. emove the existing wire harness containing the blower power wires from the inner blower access door support column and the furnace control board, including the wires in the harness which go to the limits (supply air limit and either the vent limit, on select models, or the fl ame roll-out limit). ANING Failure to remove the existing high voltage harness in this step may damage new motor or control board if VSHE kit is connected. 7. Install the new modifi ed blower assembly into the furnace, making sure that the sides of the blower are captured by all of the blower mounting tabs in the blower deck. Secure the blower with the screws removed in step. 8. Install one end of the new 77 wiring harness (loose harness included in kit) by attaching the female 9-pin AMP panel connector to the inner blower access door. 9. Install the plug of the blower wires harness into the receptacle inner blower access door. 0. e-install the inner blower access door.. Mount the motor control board to the mounting bracket (included in kit). Then mount the mounting bracket onto inside wall of the furnace using the mounting holes on the right furnace side wall.

4 . Mount the power choke (applicable with ¾ and hp motors only) onto the inner blower access door using the mounting holes provided.. Attach the other leads of the 77 wiring harness from the inner blower access support column (in step 8). onnect the 8-pin plug onto the motor control board Blower Motor receptacle. onnect the blue limit wires of the harness to the supply air limit and either the vent limit (on select models) or the fl ame roll-out limit (the limits that had the harness removed from in Step ). Attach the white wire of the harness to the VA_L _OUT terminal on the motor control board. Attach the black wire of the wire harness to either L terminal on the motor control board. ( / or hp motor units, attach the black wire of the harness to the motor choke male quick-connect terminal, then use the long, black extra wire included in the kit to connect the other lead of the choke to the L terminal of the motor control board.). Attach the A0 or 70 harness (loose harness included in kit) from the furnace control board Expansion Port to the motor control board Expansion Port.. Attach the short, black extra wire included in the kit from the other L terminal on the motor control board to the LA terminal on the furnace control board. Attach the extra white wire included in the kit from the VA_L _IN terminal on the motor control board to an open Neutral terminal on the furnace control board.. Verify all wires are connected to the furnace according to the wiring diagram. Additionally, verify all wires which are factory connected and tighten as necessary. 7. Use wire ties to secure wires away from moving parts, burner area, and to keep wires neat. 8. efer to section marked onfi guring the Blower. 9. eplace current wiring diagram with new wiring diagram for the application which is included in the kit. 0. eplace doors. estore power to the furnace. Installation is now complete. G7 VSHE Blower Upgrade Kit - SKU Loose harness descriptions: For Upflow Furnace: A9 or 700 Male 9-pin AMP mate-n-lok to -pin power connector, blue wire with female Q, black wire with female Q, and white wire with female Q Note: Airfl ow Labels for all sizes of the furnace are supplied in the kit. Select the correct Airfl ow Label and place it on the motor control mounting bracket cover in upfl ow applications or on the back of the access panel on downfl ow applications: 7079 for A cabinet size furnaces 7079 for B cabinet size furnaces 7079 for cabinet size furnaces for D cabinet size furnaces Upgrade Kit Installations Upflow. Disconnect electrical power to the furnace.. emove the upper and lower access doors from the furnace.. emove or back-out the ground screws from the top of the blower deck to allow the blower to slide out of the furnace.. Unplug the existing electrical connector containing the blower wires from the receptacle located on the right side of the blower deck.. emove the blower assembly from the furnace by removing the screws attaching the blower to the blower deck and sliding the blower assembly out of the furnace.. emove the cover from the motor control board bracket located on the front of the blower. 7. emove the existing blower wire harness from the blower assembly by unplugging the black and white power wires from the motor, the blue wire from the blower limit, and the -pin connector from the motor control board. emove blue wire from on board. 8. eplace the Fixed Speed Motor ontrol Board on the mounting bracket with the Variable Speed Motor ontrol Board which is included with the kit. econnect blue wire removed from on FSHE to the output on VSHE Board. 9. oute the black and white power wires from the motor through the wire grommet in the motor control mounting bracket. onnect the white motor power wire to the VA_L _OUT terminal on the motor control board. onnect the black wire to either L terminal on the motor control board. Leave the green motor ground attached to the blower housing. 0. oute the low voltage 8-pin connector from the motor through the wire grommet in the motor control mounting bracket. onnect the 8-pin connector to the Blower Motor receptacle on the motor control board.. Install the new A9 or 700 wire harness, routing the pin connector and the black and white power wires through the wire grommet on the motor control mounting bracket. onnect the -pin connector to the Expansion Port on the motor control board. onnect the white wire to the VA_L _IN terminal on the blower control board. onnect the black wire to the other L terminal not used in Step 8 on the

5 motor control board. ( / or hp motor units, attach the black wire of the harness to the motor choke male quick-connect terminal, then the other lead of the choke to the L terminal of the motor control board.). Slide the blower assembly back into the furnace. Be sure that the sides of the blower are captured by all of the blower mounting tabs in the blower deck. Secure with the screws removed in step.. eplace the ground screws attaching the ground wires to the blower deck removed in step.. Attach the new harness 9-pin plug to the receptacle on the right side of the blower deck.. Verify all wires are connected to the furnace according to the wiring diagram. Additionally, verify all wires which are factory connected and tighten as necessary.. Use wire ties to secure wires away from moving parts, burner area, and to keep wires neat. 7. efer to section marked onfi guring the Blower. If necessary to gain access to the motor control board, remove the cover of the motor control board mounting bracket. eplace when fi nished confi guring the blower. 8. eplace current wiring diagram with new wiring diagram for the application which is included in the kit. 9. eplace doors. estore power to the furnace. Installation is now complete. Upgrade Kit Installations Downflow. Disconnect electrical power to the furnace.. emove the upper and lower access doors from the furnace.. emove all wires from the connectors on the existing motor control board.. eplace the Fixed Speed Motor ontrol Board on the mounting bracket with the Variable Speed Motor ontrol Board which is included with the Upgrade Kit.. e-attach the leads of the existing wiring harness to the new motor control board. onnect the 8-pin plug onto the motor control board Blower Motor receptacle. emove the white wire of the blower motor harness from the Neutral connector on the furnace control board and attach it to the VA_L _OUT terminal on the motor control board. emove the black wire from the LA terminal on the furnace control board and attach it to either L terminal on the motor control board. ( / or hp motor units, the black power wire coming from the motor choke needs to be removed from the LA terminal and connected to the L terminal of the motor control board.). e-attach the -pin board-to-board harness from the furnace control board Expansion Port to the motor control board Expansion Port. 7. Attach the short black extra wire included in the kit from the other L terminal on the motor control board to the LA terminal on the furnace control board. Attach the extra white wire included in the kit from the VA_L _IN terminal on the motor control board to an open Neutral terminal on the furnace control board. econnect blue wire removed from on FSHE board to output on VSHE. 8. Verify all wires are connected to the furnace according to the wiring diagram. Additionally, verify all wires which are factory connected and tighten as necessary. 9. Use wire ties to secure wires away from moving parts, burner area, and to keep wires neat. 0. efer to section marked onfi guring the Blower.. eplace current wiring diagram with new wiring diagram for the application which is included in the kit.. eplace doors. estore power to the furnace. Installation is now complete.. ONFIGUING THE BLOE The variable speed high effi ciency blower kit is equipped with a microprocessor-controlled variable speed motor that is pre-programmed to deliver optimum airfl ow in a variety of conditions and system confi gurations. Before operation, the variable speed high effi ciency blower kit must be confi gured to match the unit with the system, system options, and climatic conditions. ith the variable speed high effi ciency blower kit installed and confi gured properly, the furnace will respond directly to thermostat inputs. During normal operation, the motor will gradually change speed in response to changes in the system variables, such as the thermostat settings, duct static, fi lter, etc. The variable speed high effi ciency blower kit is confi gured by setting the 8 switches located on the motor control board as described below. Note: hen used as a part of an iq Drive System, the blower airfl ow is controlled by the iq Drive thermostat, not the "HEAT" and "OOL" switches on the motor control board - these switches are ignored. However, it is necessary to set the fi rst "A/B" selector switch to select an "A" or "B" cabinet size, if applicable(see section "Selecting the abinet Size"). Also see iq Drive instructions.

6 IMPOTANT The variable speed high efficiency blower kit is designed to give the installer maximum flexibility to optimize system performance, efficiency, and comfort. Because there are so many way to configure the kit, it is important to read and follow these instructions carefully. Selecting the abinet Size The furnace cabinet size may be selected by setting the fi rst switch marked "A/B". For an A-size furnace, this switch should be set to 0 or "off". For a B-size furnace, this switch should be set to or "on". For a - or D-size furnace, the switch setting does not matter - it may be set to either "on" or "off". Selecting the (Gas) Heating Airfl ow The heating airfl ow is selected by setting switches through (also marked as HEAT) on the motor control board. efer to the Airfl ow Settings graph and select an airfl ow to allow the furnace to reach an appropriate heat rise as shown on the unit rating plate. To reduce the heat rise, select a higher airfl ow; to increase the heat rise, select a lower airfl ow. Be sure that the selected rise is within the specifi cation of the furnace as shown on the furnace rating label. Determining Nominal System apacity (A/ & HP) In order to select the appropriate airfl ow for the A and HP operation, the nominal system capacity must be known. The nominal system capacity is ALAYS the nominal capacity of the outdoor unit. In some cases, the nominal system capacity is not the same as the nominal capacity of the indoor coil. Selecting the ooling/heat Pump Airfl ow The cooling/heat pump airfl ow is selected by setting switches through 8 (also marked as OOL) on the motor control board. All airfl ows for other modes of operation, except for gas heat, are determined by this setting. efer to the Airfl ow Settings graph and select an airfl ow in the range recommended for the nominal system capacity. For maximum capacity and energy effi ciency, generally a selection at or near the top of the FM range for that nominal system capacity is best. For maximum dehumidifi cation, select an airfl ow near the middle or bottom of the FM range for that nominal system capacity. Note: If coil icing is observed, the cooling/heat pump airfl ow may be set too low. Double-check to be sure the setting selected is within the range shown. Also, check to be sure the system is properly charged (see outdoor unit installation instructions). If icing continues to occur, raise the selected airfl ow one or two steps.. SYSTEM OPEATION (Gas) Heating Mode hen the thermostat calls for heating, the circuit between and is completed. The furnace control board initiates the ignition sequence. Approximately 0 seconds after the gas fl ame has proven, the blower motor will slowly ramp up to the selected motor airfl ow. The blower will continue to operate after the call for heat has been removed for a selectable (switch on furnace control board) number of seconds. Note: All on- and off-delays for heating continue to be controlled by the furnace control board. ooling or Heat Pump Mode hen the thermostat calls for cooling or heat pump heating, the circuit between, G, and Y (O is ignored by the blower) is completed. The blower slowly ramps up to the selected cooling airfl ow. If there is a humidistat connected to the motor control board calling for humidity control, the motor will operate at 7% of the airfl ow setting. Or, if the system is installed where humidity control is desired but a humidistat is not available, the DEHUM and terminals on the motor control board may be jumpered. In this case, the blower will operate at 7% airfl ow for the fi rst 0 minutes of the cycle and then return to normal torque for the remainder of the cooling cycle. After the call for cooling or heat pump is satisfi ed, the blower continues to operate for 0 seconds at 0% of the selected airfl ow. Manual Fan hen the manual fan switch on the thermostat is on, energizing G only, the blower will ramp up to 0% of the selected cooling/heat pump motor airfl ow.. FAULT ONDITIONS There is a green and a red LED labeled Status on the motor control board to provide system faults as described below. Diagnostic Description ed LED (AN) Green LED (AN) ontrol Fault (No Power) Off Off Normal Operation Motor Fault Flash No Motor Fault Flash ommunications Fault Flash Flash Table. Fault onditions

7 PAT OF MOTO FM L-OUT L-IN L L MOTO ONTOL BOAD 8-00 INPUTS DHUM Y FAN SPEED HEAT OOL SEN / AND HP MOTOS ONLY NONE MODE PM NONE OMMON FAULT HP (PM) SPEED DX+ DX- If any of the original wire as supplied with the furnace must be replaced, it must be replaced with wiring material having a temperature rating of at least 0. Use copper conductors only V OUTPUTS Y/Y Y H X X GEEN BON Variable Speed High Efficiency Blower Kit Single Stage Upflow Furnaces OPTIONAL HUMIDISTAT (NOMALLY OPEN) FO -STAGE ONDENSING UNIT THEMOSTAT / BLK STIPES TO OUTDOO UNIT efer to the Installation Instructions provided with the kit for the proper heating and cooling speeds for your application. LEGEND: FIELD IING V BLK / STIPES LO VOLTAGE HIGH VOLTAGE V AMP FUSE FLAME OLL-OUT SITH VENT SITH (ON SELET MODELS) SUPPLY AI OM BL Y G BL OFF DELAY 9 8 GEEN 7 IE NUT FLAME SENSO BL LA GAS VALVE PESSUE SITH (ON SELET MODELS) LO ML MH HIGH EA L XFM HUM NEUTALS IGNITO DOO SITH INDUE PESSUE SITH X 0V (NEUTAL) GOUND GEEN OM FUNAE ONTOL FAULT ONDITIONS Diagnostic Description Green LED ed LED ontrol Fault (No Power) Off Off L / Neutral Polarity Fault Flash Flash Hour Lockout Alternating Flash Normal Operation MOTO ONTOL FAULT ONDITIONS Diagnostic Description ed LED Green LED ontrol Fault (No Power) Off Off Pressure Switch losed Fault Flash Pressure Switch Open Fault Flash Open Limit Switch Fault Flash Off Motor Fault Normal Operation Motor Fault Flash No Motor Fault Flash ommunications Fault Flash Flash Off Yellow LED ontinuous Flash Diagnostic Description Low Flame Sensor Signal Flame Present 7

8 FM MOTO PAT OF MOTO BL DEK (SELET MODELS) L-OUT L-IN OUTPUTS TO OUTDOO UNIT L L Y/Y Y MOTO ONTOL BOAD 8-00 LEGEND: FIELD IING H LO VOLTAGE HIGH VOLTAGE FO -STAGE ONDENSING UNIT OPTIONAL HUMIDISTAT (NOMALLY OPEN) Variable Speed High Efficiency Blower Kit Down Flow Single Stage Furnaces THEMOSTAT / BLK STIPES 0V V efer to the Installation Instructions provided with the kit for the proper heating and cooling speeds for your application. BLK / STIPES V AMP FUSE INPUTS DHUM OM FLAME OLL-OUT SITH VENT SITH (ON SELET MODELS) SUPPLY AI BL Y BL FAN SPEED HEAT OOL SEN 7090 X Y G NONE MODE PM NONE OMMON FAULT HP (PM) SPEED BL OFF DELAY 9 GEEN X 8 7 FLAME SENSO DX+ DX- LA GAS VALVE LO ML MH HIGH EA L XFM HUM NEUTALS IGNITO PESSUE SITH (ON SELET MODELS) -BK- () INDUE DOO SITH V (NEUTAL) GOUND PESSUE SITH GEEN FUNAE ONTOL FAULT ONDITIONS 9-PIN HOUSING 9-PIN PLUG / AND HP MOTOS ONLY Diagnostic Description Green LED ed LED ontrol Fault (No Power) Off Off L / Neutral Polarity Fault Flash Flash Alternating Flash Hour Lockout If any of the original wire as supplied with the furnace must be replaced, it must be replaced with wiring material having a temperature rating of at least 0. MOTO ONTOL FAULT ONDITIONS Diagnostic Description ed LED Green LED ontrol Fault (No Power) Off Off Normal Operation Pressure Switch losed Fault Flash Pressure Switch Open Fault Flash Open Limit Switch Fault Flash Off Motor Fault Off Yellow LED Use copper conductors only. Normal Operation Motor Fault Flash No Motor Fault Flash ommunications Fault Flash Flash ontinuous Flash Diagnostic Description Low Flame Sensor Signal Flame Present 8

9 FAULT ONDITIONS Diagnostic Description Green LED ed LED ontrol Fault (No Power) Off Off L / Neutral Polarity Fault Flash Flash Hour Lockout Alternating Flash Normal Operation Pressure Switch losed Fault Flash Pressure Switch Open Fault Flash Open Limit Switch Fault Flash Off Off Fault Motor Diagnostic Description Yellow LED Low Flame Sensor Signal ontinuous Flash Flame Present FM MOTO DHUM Y SEN L-IN L-OUT L-IN PM MODE L-OUT PAT OF MOTO SPEED FAULT OMMON HP OOL HEAT FAN SPEED OPEN OPEN GEEN MOTO HOKE (ON / AND HP MOTOS ONLY) DX+ DX- X Y/Y Y H BLOE BLOE BON GEEN For 80+ and 90+ -Stage Variable Speed Upflow Furnaces If any of the original wire as supplied with the furnace must be replaced, it must be replaced with wiring material having a temperature rating of at least 0. This wiring diagram shows connections and termination required for the blower kit only. Use in addition to the wiring diagram for the furnace. efer to the Installation Instructions provided with the kit for the proper heating and cooling speeds for your application. Use copper conductors only. / BLK STIPES ONDENSATE (ON SELET MODELS) LO V 0 V BLK / STIPES PESSUE SITH PESSUE SITH HIGH VIOLET PESSUE SITH PESSUE SITH X OM Y/Y Y G VIOLET VIOLET GEEN GAS VALVE BON BON LO HI BL OFF DELAY FLAME SENSO LINE- N LINE- N XMF-N HUM LINE LINE XMF EA BON GEEN VENT (ON SELET MODELS) FLAME OLL-OUT SUPPLY AI DOO SITH (NEUTAL) 0V GOUND GEEN INDUE H IGNITO L LEGEND: FIELD IING LO VOLTAGE HIGH VOLTAGE 9

10 For 80+ and 90+ -Stage Variable Speed Downflow Furnaces FAULT ONDITIONS Diagnostic Description Green LED ed LED ontrol Fault (No Power) Off Off L / Neutral Polarity Fault Flash Flash If any of the original wire as supplied with the furnace must be replaced, it must be replaced with wiring material having a temperature rating of at least 0. This wiring diagram shows connections and termination required for the blower kit only. Use in addition to the wiring diagram for the furnace. efer to the Installation Instructions provided with the kit for the proper heating and cooling speeds for your application. Hour Lockout Alternating Flash Normal Operation Pressure Switch losed Fault Flash Pressure Switch Open Fault Flash Open Limit Switch Fault Flash Off Motor Fault Off Use copper conductors only. Diagnostic Description Yellow LED Low Flame Sensor Signal ontinuous Flash Flame Present / BLK STIPES V 0 V PAT OF MOTO BLK / STIPES LO PESSUE SITH HIGH PESSUE SITH L-IN SEN DHUM Y LOUT L-IN FM MOTO X OM Y/Y Y G VIOLET VIOLET PM MODE L-OUT SPEED FAULT OMMON HP OOL HEAT FAN SPEED 0 GEEN OPEN OPEN GEEN GAS VALVE DX+ DX- BON 7 8 BON LO HI 7 8 X FLAME SENSO MOTO HOKE (ON / AND HP MODELS ONLY) BL OFF DELAY Y/Y Y H LINE- N LINE- N XMF-N HUM LINE LINE XMF EA FLAME OLL-OUT SUPPLY AI VENT (ON SELET MODELS) DOO SITH (NEUTAL) 0V GOUND BLOE BLOE DEK BLOE GEEN INDUE H IGNITO L LEGEND: FIELD IING LO VOLTAGE HIGH VOLTAGE 0

11 Nominal Heating Airflows (FM) and erature ise ( F) A abinet *SA-0(ŧ)-*A *SA/SK-0(ŧ)-*A *S-08D-*A Models Models Models Switch Settings Input (BTU) Input (BTU) Input (BTU) HEAT A/B FM ise ( F) FM ise ( F) FM ise ( F) B abinet *SA/SK-07(ŧ)-*B *SA/SK-090(ŧ)-*B *S/SL-0D-*B *S/SL-07D-*B Models Models Models Models Switch Settings Input (BTU) Input (BTU) Input (BTU) Input (BTU) HEAT A/B FM ise ( F) FM ise ( F) FM ise ( F) FM ise ( F) abinet *SA-07(ŧ)-* *SA-090(ŧ)-* *SA/SK-08(ŧ)-* *S-07D-* *S/SL-090D-* Models Models Models Models Models Switch Settings Input (BTU) Input (BTU) Input (BTU) Input (BTU) Input (BTU) HEAT A/B FM ise ( F) FM ise ( F) FM ise ( F) FM ise ( F) FM ise ( F) # # # # # # # # D abinet *SA/SK-(ŧ)-*D *S-08D-*D *S/SL-0D-*D Models Models Models Switch Settings Input (BTU) Input (BTU) Input (BTU) HEAT A/B FM ise ( F) FM Single Stage Furnace ise ( F) FM ise ( F) # # # # # # # # # Switch not used - can be 0 or Notes:. Two openings are recommended for airfl ows above 00 FM if the fi lter(s) is (are) adjacent to the furnace.. erature rises in the table are approximate. Actual temperature rises may vary.. erature rises that are shaded in grey are for reference only. These conditions are not recommended.

12 ooling/heat Pump Airflows A abinet B abinet Switch Settings Nominal A/ and HP Switch Settings FM FM HEAT OOL apacity HEAT OOL A/B 7 8 LO HIGH A/B 7 8 LO FM Nominal A/ and HP apacity TON TON TON TON TON TON. TON TON abinet D abinet Switch Settings Nominal A/ and Switch Settings FM HEAT OOL HP apacity HEAT OOL FM A/B 7 8 LO FM A/B 7 8 LO FM # # # TON. TON # # # # # # # TON # # # TON # # # # # # # # TON # # # # # # # 0 90 # 0 9 # # # Nominal A/ and HP apacity TON TON. TON # Switch not used - can be 0 or

13 Two - Stage Furnace Natural Heating Airflows (FM) and erature ise ( F) A ABINET Switch Settings (HEAT) *TA/TK-00( )-*VA Input (BTU) 0,000 FM ise ( F) ,00 0 0,0 0 0,00 7 Switch Settings (HEAT) B ABINET *TA/TK-080( )-*VB Input (BTU) 80,000 *TA/TK-00( )-*VB Input (BTU) 00,000 FM ise ( F) FM ise ( F) 0 0 0,000 9, ,00, ,00 9,00 0,00, ,00,00 0,00 0,00 9 0,00 7,00,700,700 Switch Settings (HEAT) ABINET *TA/TK-00( )-*V Input (BTU) 00,000 *TA/TK-0( )-*V Input (BTU) 0,000 FM ise ( F) FM ise ( F) # 0 0 0,000 7, # 0 0,, 80 # 0 0,0 0,0 7 # 0,, # 0 0,0,0 # 0,7 7,7 # 0,90,90 #,80,80 9 D ABINET Switch Settings (HEAT) *TA/TK-0( )-*VD Input (BTU) 0,000 FM ise ( F) # 0 0 0,00 9 # 0 0, # 0 0,70 0 # 0,8 # 0 0,90 # 0,07 0 # 0,90 7 #,0 NOTES: # Switch not used - can be 0 or. Two openings are recommended for airflows above,00 FM if the filter(s) is (are) adjacent to the furnace.. erature rises in the table are approximate. Actual temperature rises may vary.. erature rises shaded in grey are for reference only. These conditions are not recommended.

14 Nominal Heating Airflows (FM) and erature ises ( F) for Furnaces with - Variable Speed B ABINET *T/TL-00D-*B Switch Settings (HEAT) Input (BTU) 0,000 FM ise ( F) 0 0 0, , ,00 0,00 0 0,00 8 0,00 0,00,700 Switch Settings (HEAT) ABINET *T/TL-080D-* Input (BTU) 80,000 *T/TL-00D-* Input (BTU) 00,000 FM ise ( F) FM ise ( F) # 0 0 0,000 70, # 0 0,, 79 # 0 0,0 7,0 7 # 0,, # 0 0,0 8,0 0 # 0,7,7 # 0,90,90 #,80 9,80 9 D ABINET *T/TL-0D-*D Switch Settings (HEAT) Input (BTU) 0,000 FM ise ( F) # 0 0 0,00 70 # 0 0, # 0 0,70 # 0,8 7 # 0 0,90 # 0,07 # 0,90 8 #,0 Notes: # Switch not used - can be 0 or. Two openings are recommended for airflows above,00 FM if the fi lter(s) is (are) adjacent to the furnace.. erature rises in the table are approximate. Actual temperature rises may vary.. erature rises shaded in grey are for reference only. These conditions are not recommended.

15

16 O'Fallon, MO 70888Z (replaces 70888B) Specifi cations and illustrations subject to change without notice and without incurring obligations. Printed in U.S.A. (07/09)

Installation Instructions

Installation Instructions HHK Series Installation Instructions Electric Heater Kits Installation in Standard and Variable Speed Indoor Air Handlers! IMPOTANT: The instructions included with this heater kit are for installations

More information

Installation Instructions

Installation Instructions H6HK Series Installation Instructions Electric Heater Kits Installation in Standard and Variable Speed Indoor Air Handlers IMPORTANT: The instructions included with this heater kit are for installations

More information

Installation Instructions

Installation Instructions Installation Instructions B5BV Series Electric Furnaces For HUD approved installations in manufactured homes and modular homes These instructions are intended to assist qualified individuals experienced

More information

Installation Instructions

Installation Instructions Installation Instructions System Field Wiring Instructions SOPE This document describes basic fi eld wiring required to interconnect components of NODYNE iq Drive heating and air conditioning systems.

More information

FG6T(C,L) Series. High Efficiency / Direct Vent or Non Direct Vent 2-Stage Condensing Gas Furnace with Variable Speed Blower TECHNICAL SPECIFICATIONS

FG6T(C,L) Series. High Efficiency / Direct Vent or Non Direct Vent 2-Stage Condensing Gas Furnace with Variable Speed Blower TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS FG6T(C,L) Series High Efficiency / Direct Vent or Non Direct Vent 2-Stage Condensing Gas with Variable Speed Blower 92+ Upflow/Horizontal 90+ Downflow The high effi ciency 2-Stage

More information

KG6TE Series. High Efficiency / Direct Vent or Non Direct Vent 2-Stage Condensing Gas Furnace with Variable Speed Blower TECHNICAL SPECIFICATIONS

KG6TE Series. High Efficiency / Direct Vent or Non Direct Vent 2-Stage Condensing Gas Furnace with Variable Speed Blower TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS KG6TE Series High Efficiency / Direct Vent or Non Direct Vent 2-Stage Condensing Gas with Variable Speed Blower 95.1 Upflow/Horizontal The high effi ciency 2-Stage gas furnace

More information

5.0 AIR HANDLER EQUIPPED WITH THE COMFORT CONTROL 2 SYSTEM INTERFACE BOARD

5.0 AIR HANDLER EQUIPPED WITH THE COMFORT CONTROL 2 SYSTEM INTERFACE BOARD 5.0 AI HANDLE EQUIPPED WITH THE OMFOT ONTOL 2 SYSTEM INTEFAE BOAD FIGUE 8 THE AI HANDLE OMFOT ONTOL 2 SYSTEM ONTOL BOAD The HPN-series of air handlers are designed to operate with conventional 24VA controls

More information

KG6RC Series TECHNICAL SPECIFICATIONS FEATURES AND BENEFITS

KG6RC Series TECHNICAL SPECIFICATIONS FEATURES AND BENEFITS TECHNICAL SPECIFICATIONS KG6RC Series High Efficiency / Direct Vent or Non Direct Vent Condensing Upflow/ Horizontal Gas Furnace Induced Draft - 92+ AFUE Input 40,000-120,000 Btuh The high effi ciency

More information

FG7T (C and L Series)

FG7T (C and L Series) TECHNICAL SPECIFICATIONS FG7T (C and L Series) WARRANTY Smartlite Two Stage, Variable Speed, Condensing Upflow/Horizontal and Downflow Gas Furnaces Induced Draft - 95.1 AFUE Input 60,000-120,000 Btuh The

More information

5.0 AIR HANDLER Comfort Control 2 System INTERFACE BOARD

5.0 AIR HANDLER Comfort Control 2 System INTERFACE BOARD 5.0 AI HANDLE omfort ontrol 2 System INTEFAE OAD FIGUE 8 THE AI HANDLE ONTOL OAD EQUIPPED WITH THE omfort ontrol 2 System The HPL-series of air handlers are designed to operate with conventional 24VA controls

More information

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Model PGC2T (C and L) Series SmartStart M1200 Product Line Two Stage, Variable Speed, High Efficiency Upflow/Horizontal and Downflow Gas Furnaces 95.1 AFUE Input 60,000-120,000

More information

G6RC Series TECHNICAL SPECIFICATIONS

G6RC Series TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS G6RC Series High Efficiency / Direct Vent or Non Direct Vent Condensing Upflow/ Horizontal Gas Furnace Induced Draft - 92+ AFUE Input 40,000-120,000 Btuh The high effi ciency upfl

More information

Installation in Standard & Variable Speed Indoor Air Handlers IMPORTANT

Installation in Standard & Variable Speed Indoor Air Handlers IMPORTANT H6HK Series Electric Heater Kit INSTALLATION INSTRUCTIONS Installation in Standard & Variable Speed Indoor Air Handlers IMPORTANT These instructions are primarily intended to assist qualified individuals

More information

Installation Instructions

Installation Instructions Split System Indoor Coils Installation Instructions CAUTION: Read the Installation Instructions supplied with furnace/air handler and observe all safety requirements outlined in instructions and/or furnace/air

More information

Installation Instructions

Installation Instructions Split System Indoor Coils Installation Instructions CAUTION: Read the Installation Instructions supplied with furnace/air handler and observe all safety requirements outlined in instructions and/or furnace/air

More information

Important Information

Important Information Electric Central - & Relay Installation Instructions For Models E(1,)E(H,B) Series The p/n 9098 -wire and p/n 90987 A/C Heat Pump ( to 7 wire) es install with current models of the E1 and E NORDYNE electric

More information

WARNING CAUTION 50T INSTALLATION INSTRUCTIONS DESCRIPTION PRECAUTIONS. Integrated Furnace Control

WARNING CAUTION 50T INSTALLATION INSTRUCTIONS DESCRIPTION PRECAUTIONS. Integrated Furnace Control 50T35-743 Integrated Furnace Control INSTALLATION INSTUCTIONS FAILUE TO EAD AND FOLLO ALL INSTUCTIONS CAEFULLY BEFOE INSTALLIN O OPEATIN THIS CONTOL COULD CAUSE PESONAL INJUY AND/O POPETY DAMAE. DESCIPTION

More information

ZONE PANEL KIT INSTALLATION MANUAL COMMUNICATING ZONE PANEL KIT - (S1-TCZCB01A) ZONE PANEL WITH ZONING TOUCH SCREEN FIRMWARE

ZONE PANEL KIT INSTALLATION MANUAL COMMUNICATING ZONE PANEL KIT - (S1-TCZCB01A) ZONE PANEL WITH ZONING TOUCH SCREEN FIRMWARE ZONE PANEL KIT INSTALLATION MANUAL OMMUNIATING ZONE PANEL KIT - (S1-TZB01A) ZONE PANEL WITH ZONING TOUH SEEN FIMWAE FO USE WITH TOUH SEEN OMMUNIATING ONTOL MODELS: S1-TTS GENEAL INFOMATION This kit is

More information

Design & Installation for. Zonex Systems. System Zone Auto Changeover. System Zone Manual Changeover

Design & Installation for. Zonex Systems. System Zone Auto Changeover. System Zone Manual Changeover Design & Installation for Zonex Systems System 2000 2-20 Zone Auto hangeover System 1000 2-7 Zone Manual hangeover Part #101ASIM ev. September 2003 TABLE OF ONTENTS System 2000 System Operation...1 omponents...1

More information

User s Manual. THE iq Drive SYSTEM USER S INFORMATION IMPORTANT. Variable Speed Ultra-High SEER Split System IMPORTANT NOTE

User s Manual. THE iq Drive SYSTEM USER S INFORMATION IMPORTANT. Variable Speed Ultra-High SEER Split System IMPORTANT NOTE User s Manual Variable Speed Ultra-High SEER Split System These units have been designed and tested for capacity and effi ciency in accordance with ARI standards. These outdoor air conditioning units are

More information

USER S MANUAL AND INSTALLATION INSTRUCTIONS IMPORTANT

USER S MANUAL AND INSTALLATION INSTRUCTIONS IMPORTANT USER S MANUAL AND INSTALLATION INSTRUCTIONS P3BD Series 13 SEER Single Package Air Conditioner IMPORTANT Read this owner information to become familiar with the capabilities and use of your appliance.

More information

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Model PGF1TA 2 Stage Series Upflow/Horizontal M1010 Product Line High Efficiency / 80+ Upflow/Horizontal 2 Stage Gas Furnace with Variable Speed Blower 2 10 YEAR WARRANTY WORRY-FREE

More information

NOT DESTROY. PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

NOT DESTROY. PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE. B6BM, B6EM, & B6VM Series Installation Instructions AI HANDLE IMPOTANT Please read all information in this manual thoroughly and become familiar with the capabilities and use of your appliance before attempting

More information

USER'S MANUAL/INSTALLATION INSTRUCTIONS

USER'S MANUAL/INSTALLATION INSTRUCTIONS TM USER'S MANUAL/INSTALLATION INSTRUCTIONS P Series Single Package Convertible Air Conditioner Single Package Convertible Air Conditioner IMPORTANT These instructions are primarily intended to assist qualifi

More information

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS TM TECHNICAL SPECIFICATIONS Model PGF1TE 2 Stage Series Upflow/Horizontal M1010 Product Line High Efficiency / 95.1 AFUE Direct Vent or Non Direct Vent Condensing Furnace 10 YEAR WARRANTY WORRY-FREE PERFORMANCE

More information

Installation instructions for Plenum-mounted add-on electric heaters MODEL TU. MARCH 2011 version 7

Installation instructions for Plenum-mounted add-on electric heaters MODEL TU. MARCH 2011 version 7 Installation instructions for Plenum-mounted add-on electric heaters MODEL TU MARCH 2011 version 7 THERMOLEC PLENUM HEATER MODEL TU BEFORE YOU START -GENERAL SAFETY AND INSTALLATION PRECAUTIONS Please

More information

INSTALLATION INSTRUCTIONS Fan Coils FVM2X, FVM4X

INSTALLATION INSTRUCTIONS Fan Coils FVM2X, FVM4X Fan oils FVM2X, FVM4X These instructions must be read and understood completely before attempting installation. DANGE, WANING, AUTION, and NOTE The signal words DANGE, WANING, AU- TION, and NOTE are used

More information

INSTALLATION GUIDE. AAN & AEN Series - Manufactured Housing Electric Furnace. 1. Safety Instruction. 2. Inspection ! CAUTION CAUTION `!

INSTALLATION GUIDE. AAN & AEN Series - Manufactured Housing Electric Furnace. 1. Safety Instruction. 2. Inspection ! CAUTION CAUTION `! INSTALLATION GUIDE AAN & AEN Series - Manufactured Housing Electric Furnace. Safety Instruction Potential safety hazards are alerted using the following symbols. The symbol is used in conjunction with

More information

INSTALLATION MANUAL MODULAR VARIABLE SPEED AIR HANDLERS MODELS: MV LIST OF SECTIONS LIST OF FIGURES LIST OF TABLES SECTION I: GENERAL

INSTALLATION MANUAL MODULAR VARIABLE SPEED AIR HANDLERS MODELS: MV LIST OF SECTIONS LIST OF FIGURES LIST OF TABLES SECTION I: GENERAL INSTALLATION MANUAL MODULA VAIABLE SPEED AI HANDLES MODELS: MV ISO 9001 ertified Quality Management System GENEAL.............................................. 1 SAFETY................................................

More information

G71MPP WARNING. WARNING Sharp edges. Be careful when servicing unit to avoid sharp edges which may result in personal injury. Service Literature

G71MPP WARNING. WARNING Sharp edges. Be careful when servicing unit to avoid sharp edges which may result in personal injury. Service Literature Service Literature Corp. 0804 L2 Revised 05 05 2008 G71MPP G71MPP SERIES UNITS G71MPP series units are high efficiency multi position (upflow, downflow, horizontal right and left) gas furnaces equipped

More information

MX Series Indoor Modular Blowers ModuleFlex Electric or Hot Water Heat with available Variable-Speed High Efficiency ECM Motor

MX Series Indoor Modular Blowers ModuleFlex Electric or Hot Water Heat with available Variable-Speed High Efficiency ECM Motor IM-MAH-0662403-11 November 2017 Installation Instructions MX Series Indoor Modular Blowers ModuleFlex Electric or Hot Water Heat with available Variable-Speed High Efficiency EM Motor TABLE OF ONTENTS

More information

ICM Simple Systems. CC750 Comfort Control Center CC and CC Application Guide

ICM Simple Systems. CC750 Comfort Control Center CC and CC Application Guide ICM Simple Systems CC750 Comfort Control Center CC750-115 and CC750-230 Application Guide For more information on our complete range of American-made products plus wiring diagrams, troubleshooting tips

More information

Wiring: All wiring should be conventional 18 gauge thermostat wire. Thermostats and zone dampers may be located up to 300 feet from the Z-300 panel.

Wiring: All wiring should be conventional 18 gauge thermostat wire. Thermostats and zone dampers may be located up to 300 feet from the Z-300 panel. THE EEN Z NE Z EE THE NE N Sequence of Operation: The reen Zone Z-300-HPS is a residential / light commercial zone control system that allows a single HVA unit to have up to three separate zones. Each

More information

MBVC. Variable-Speed, ComfortNet - Compatible Modular Blowers. Cooling Capacity: 18,000-60,000 BTU/h

MBVC. Variable-Speed, ComfortNet - Compatible Modular Blowers. Cooling Capacity: 18,000-60,000 BTU/h MBV Variable-Speed, omfortnet - ompatible Modular Blowers ooling apacity: 8,000-60,000 BTU/h Standard Features ompatible with the omfortnet ommunication System family of products Variable-speed EM blower

More information

LRP14HP/LRP14DF/LRP14AC/LRP14GE/LRP16GE/LRP16HP SERIES UNITS

LRP14HP/LRP14DF/LRP14AC/LRP14GE/LRP16GE/LRP16HP SERIES UNITS Service Literature orp. 1501-L2 August 2016 Revised March 2017 LRP14HP/DF/A/GE LRP16GE/HP 2 to 5 Ton (7.0 to 17.6 kw) LRP14HP/LRP14DF/LRP14A/LRP14GE/LRP16GE/LRP16HP SERIES UNITS The LRP14/16 series packaged

More information

G60UH(X) WARNING. WARNING Sharp edges. Be careful when servicing unit to avoid sharp edges which may result in personal injury. Service Literature

G60UH(X) WARNING. WARNING Sharp edges. Be careful when servicing unit to avoid sharp edges which may result in personal injury. Service Literature Service Literature Corp. 0204 L2 Revised 11 2006 G60UH(X) G60UH(X) SERIES UNITS G60UH(X) series units are mid efficiency gas furnaces used for upflow or horizontal applications only, manufactured with

More information

TECHNICAL GUIDE. Acclimate MODELS: FL9S GAS-FIRED CONDENSING / HIGH EFFICIENCY UPFLOW SINGLE STAGE FURNACES 92% AFUE

TECHNICAL GUIDE. Acclimate MODELS: FL9S GAS-FIRED CONDENSING / HIGH EFFICIENCY UPFLOW SINGLE STAGE FURNACES 92% AFUE TEHNIAL GUIDE Acclimate MODELS: FL9S GAS-FIRED ONDENSING / HIGH EFFIIENY UPFLOW SINGLE STAGE FURNAES 92% AFUE NATURAL GAS 40-135 MBH INPUT EFFIIENY RATING ERTIFIED ISO 9001 ertified Quality Management

More information

50M TYPICAL WIRING DIAGRAM 24 VAC CLASS II TRANSFORMER 24 VAC 50M COOL PARK HEAT LO HEAT HI LINE XFMR EAC HUM

50M TYPICAL WIRING DIAGRAM 24 VAC CLASS II TRANSFORMER 24 VAC 50M COOL PARK HEAT LO HEAT HI LINE XFMR EAC HUM 21M51U-843 WIIN AND CONFIUATION INTEATED HOT (LINE) TYPICAL WIIN DIAAM 120 VAC NEUTAL (LINE) 24 VAC CLASS II TANSFOME TH 24 VAC T COOL PAK HEAT LO HEAT HI LINE XFM EAC HUM CICU- LATO BLOWE HUMIDIFIE (OPTIONAL)

More information

Installation Instructions

Installation Instructions Split System Indoor Coils Installation Instructions! CAUTION: Read the Installation Instructions supplied with furnace/air handler and observe all safety requirements outlined in instructions and/or furnace/air

More information

CP-6 Installation and Operation Instructions 3 Heat / 2 Cool Heat Pump with Fossil Fuel option Auto Changeover - Cooling Priority or Majority Wins

CP-6 Installation and Operation Instructions 3 Heat / 2 Cool Heat Pump with Fossil Fuel option Auto Changeover - Cooling Priority or Majority Wins P-6 Installation and Operation Instructions 3 Heat / 2 ool Heat Pump with Fossil Fuel option Auto hangeover - ooling Priority or Majority Wins Sequence of Operation: Each zone damper is controlled by its

More information

INSTALLATION INSTRUCTIONS Fan Coils FVM4X B Series

INSTALLATION INSTRUCTIONS Fan Coils FVM4X B Series Fan oils FVM4X B Series These instructions must be read and understood completely before attempting installation. DANGE, WANING, AUTION, and NOTE The signal words DANGE, WANING, AU- TION, and NOTE are

More information

Installation Instructions

Installation Instructions Installation Instructions EHMA SERIES ELECTRIC HEATERS FOR PAM3 SERIES PACKAGE AIR CONDITIONERS PHM3 SERIES PACKAGE HEAT PUMPS TABLE OF CONTENTS SAFE INSTALLATION REQUIREMENTS... 2 GENERAL INFORMATION...

More information

Installation Instructions

Installation Instructions TM Single Package Heat Pump Installation Instructions IMPORTANT These instructions are primarily intended to assist qualifi ed individuals experienced in the proper installation of heating and/or air conditioning

More information

SERVICING S-15 CHECKING CAPACITOR

SERVICING S-15 CHECKING CAPACITOR S-15 CHECKING CAPACITOR The direct drive motors are of the permanent split capacitor design. A run capacitor is wired across the auxiliary and a portion of the main windings. The capacitors primary function

More information

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS

ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. U.S.A. WARNING FOR YOUR

More information

INSTALLATION INSTRUCTIONS Apartment Fan Coil

INSTALLATION INSTRUCTIONS Apartment Fan Coil Apartment Fan oil Product Family: FSA2X, FSA4X These instructions must be read and understood completely before attempting installation. DANE, WANIN, AUTION, and NOTE The signal words DANE, WANIN, AUTION,

More information

ICM 275. Replacement Description

ICM 275. Replacement Description IM 275 Fan ontrol enter Replacement Description The IM275 Gas Furnace ontrol enter is a new generation control for the replacement market. The IM275 Gas Furnace ontrol enter is designed to function similarly

More information

Installation Instructions

Installation Instructions Installation Instructions Indoor Air Handlers for Systems These instructions are primarily intended to assist qualifi ed individuals experienced in the proper installation of heating and/or air conditioning

More information

Electric Heat Accessory

Electric Heat Accessory Electric Heat Accessory AMFK05CHA AMFK05CHB AMFK07CHA AMFK07CHB AMFK0CHA AMFK0CHB AMFK4CHB AMFK20CHB AMFK25CHB AMFK30CHB Single Phase For Use ith Blower & Fan Coil Units and Electric Furnaces ANING Electrical

More information

SLP98UHV WARNING. WARNING Sharp edges. Be careful when servicing unit to avoid sharp edges which may result in personal injury. Service Literature

SLP98UHV WARNING. WARNING Sharp edges. Be careful when servicing unit to avoid sharp edges which may result in personal injury. Service Literature Service Literature Corp. 1029 L7 SLP98UHV SLP98UHV SERIES UNITS SLP98UHV series units are high efficiency upflow, horizontal right and left) gas furnaces equipped with variable capacity gas valve, variable

More information

G60UHV(X) WARNING. WARNING Sharp edges. Be careful when servicing unit to avoid sharp edges which may result in personal injury. Service Literature

G60UHV(X) WARNING. WARNING Sharp edges. Be careful when servicing unit to avoid sharp edges which may result in personal injury. Service Literature Service Literature Corp. 0124 L11 Revised 11 2006 G60UHV(X) G60UHV(X) SERIES UNITS G60UHV(X) series units are mid efficiency gas furnaces used for upflow or horizontal applications only, manufactured with

More information

USER'S MANUAL/INSTALLATION INSTRUCTIONS

USER'S MANUAL/INSTALLATION INSTRUCTIONS TM USER'S MANUAL/INSTALLATION INSTRUCTIONS P Series Single Package Convertible Air Conditioner Single Package Convertible Air Conditioner IMPORTANT These instructions are primarily intended to assist qualifi

More information

Installation Instructions

Installation Instructions 50ZPB, C, 50ZHB, C, PA3Z ---A, PH3Z ---A, PA4Z, PH4Z, PAJ4,PHJ4,WJA4,WJH4 SMALL PACKAGED PRODUCTS (SPP) Accessory Electric Heaters 5---20 kw For 14 SEER, R---410A Manufactured Home Installation Instructions

More information

S1-CD065T01 Central Dehumidifier Installation Instructions. Johnson Controls Unitary Products WARNING CAUTION SPECIFICATIONS LOCATION CONSIDERATIONS

S1-CD065T01 Central Dehumidifier Installation Instructions. Johnson Controls Unitary Products WARNING CAUTION SPECIFICATIONS LOCATION CONSIDERATIONS Johnson ontrols Unitary Products S1-D065T01 entral Dehumidifier Installation Instructions WANING 1. 120 volts may cause serious injury from electric shock. Disconnect electrical power before starting installation.

More information

SERVICE MANUAL FOR 6636A & 6636B SERIES TWO TON HIGH EFFICIENCY PACKAGED AIR CONDITIONERS

SERVICE MANUAL FOR 6636A & 6636B SERIES TWO TON HIGH EFFICIENCY PACKAGED AIR CONDITIONERS SERVICE MANUAL FOR 6636A & 6636B SERIES TWO TON HIGH EFFICIENCY PACKAGED AIR CONDITIONERS TABLE OF CONTENTS 1. Warnings & Component Match-Up............................................ 2 2. Unit Specifications..........................................................

More information

Model 1730A Compact Dehumidifier Installation Instructions

Model 1730A Compact Dehumidifier Installation Instructions Model 1730A ompact Dehumidifier Installation Instructions WANING 1. 120 volts may cause serious injury from electric shock. Disconnect electrical power before starting installation. Leave power disconnected

More information

USER s MANUAL & INSTALLATION INSTRUCTIONS IMPORTANT

USER s MANUAL & INSTALLATION INSTRUCTIONS IMPORTANT USER s MANUAL & INSTALLATION INSTRUCTIONS 2 Stage R-410A Single Package Heat Pump 15 SEER IMPORTANT Please read this information thoroughly and become familiar with the capabilities and use of your appliance

More information

Installation Instructions

Installation Instructions H5HK Series Installation Instructions 3 Phase Electric Heater Kits Light Commercial Package A/C and Heat Pump Systems Description Installation of 208/240V and 480V H5HK 3 Phase Heater Kits in 6, 7.5 and

More information

Installation Instructions

Installation Instructions Installation Instructions Fan oil for Puron efrigerant 002, 003, 005, 006 FV4B A98023 Fig. 1Model FV4B NOTE: ead the entire instruction manual before starting the installation. This symbol indicates a

More information

AG Series Electric Heaters

AG Series Electric Heaters AG Series Electric Heaters Installation, Operation and Maintenance Instructions Internal Auxililary Electric Heat 97B0005N03 Table of Contents Overview 3 Vertical Upflow Installation 4 Horizontal Installation

More information

50M56U-843 INSTALLER MUST READ DESCRIPTION PRECAUTIONS WARNING CAUTION

50M56U-843 INSTALLER MUST READ DESCRIPTION PRECAUTIONS WARNING CAUTION 50M56U-843 Universal Single Stage HSI Integrated Furnace Control Kit INSTALLATION INSTRUCTIONS INSTALLER MUST READ PAGE 3 CONTAINS WIRING HARNESS AND BLOWER CONNECTION INSTRUCTIONS FOR ALL APPLICATIONS

More information

Installation Instructions

Installation Instructions FFMA DIET EXPANSION FAN OIL UNIT Installation Instructions NOTE: ead the entire instruction manual before starting installation. TABLE OF ONTENTS PAGE SAFETY ONSIDEATIONS... 1 INTODUTION... 1 INSTALLATION...

More information

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Model PGF1RA Series M1010 Product Line High Efficiency / Upflow / Horizontal Gas Furnace Induced Draft - 80+ AFUEurnace 2 10 YEAR WARRANTY WORRY-FREE PERFORMANCE 5 YEAR DEPENDABILITY

More information

Your safety and the safety of others are very important.

Your safety and the safety of others are very important. VARIABLE SPEED ELECTRIC FURNACE INSTALLATION INSTRUCTIONS VARIABLE SPEED ELECTRIC FURNACE SAFETY...1 INSTALLATION REQUIREMENTS...2 Tools and Parts...2 Location Requirements...2 Installation Configurations...3

More information

Wiring Diagrams. 9AB4-12 Air-Cooled Remote Condenser INDEX OPERATING SEQUENCE ACCESSORIES LEGEND AND NOTES FOR FIG. 1-6

Wiring Diagrams. 9AB4-12 Air-Cooled Remote Condenser INDEX OPERATING SEQUENCE ACCESSORIES LEGEND AND NOTES FOR FIG. 1-6 9AB4-12 Air-ooled Remote ondenser Wiring Diagrams INDEX UNIT 9AB DRAWING TYPE DRAWING NUMBER FIG. NO. 4,6 Label Diagram 9AB6-10816 1 8,12 Label Diagram 9AB12-10816 2 AESSORIES OMPONENT PART NO. FIG. NO.

More information

TECHNICAL MANUAL MBVC

TECHNICAL MANUAL MBVC TEHNIAL MANUAL AL MBV Blowers efer to Service Manual S0000 for installation, operation, and troubleshooting information. All safety information must be followed as provided in the Service Manual. efer

More information

TECH SHEET - DO NOT DISCARD PAGE 1

TECH SHEET - DO NOT DISCARD PAGE 1 TECH SHEET - DO NOT DISCAD PAGE 1 ANING Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock.

More information

E2 Series. Downflow, Upflow Electric Furnaces TECHNICAL SPECIFICATIONS. Features and Benefits

E2 Series. Downflow, Upflow Electric Furnaces TECHNICAL SPECIFICATIONS. Features and Benefits TECHNICAL SPECIFICATIONS E2 Series Downflow, Upflow Electric Furnaces The E2 Series furnace is designed for all sizes of manufactured and modular homes. These units incorporate reliability and low maintenance.

More information

CAUTION WARNING. 50T Integrated Furnace Control INSTALLATION INSTRUCTIONS DESCRIPTION PRECAUTIONS

CAUTION WARNING. 50T Integrated Furnace Control INSTALLATION INSTRUCTIONS DESCRIPTION PRECAUTIONS 50T35-743 Integrated Furnace Control INSTALLATION INSTRUCTIONS FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY

More information

Installation Instructions Part No , Part No Part No

Installation Instructions Part No , Part No Part No Torsion-Flex Motor mount for PSC motors and Rigid-Mount for ECM motors Replacement Kit Cancels: New Installation Instructions Part No. 327752-401, Part No. 327753-401 Part No. 327754-401 IIK-310A-45-11

More information

Operator: Save these instructions for future use!

Operator: Save these instructions for future use! WHITE-ODES 1F89-11 Non-Programmable Electronic Digital Heat Pump Thermostat INSTALLATION AND OPEATION INSTUTIONS Operator: Save these instructions for future use! FAILUE TO EAD AND FOLLOW ALL INSTUTIONS

More information

GMH95/GCH9 MULTI-POSITION, DUAL$AVER CONVERTIBLE, MULTI-SPEED GAS FURNACE

GMH95/GCH9 MULTI-POSITION, DUAL$AVER CONVERTIBLE, MULTI-SPEED GAS FURNACE 95%/93% AFUE HEATING INPUT: 46,000 5,000 BTU/H Standard Features / MULTI-POSITION, DUAL$AVER ONVERTIBLE, MULTI-SPEED GAS FURNAE The Goodman / 95%/93% AFUE Dual$aver onvertible, Multi-Speed, Multi-Position

More information

Mini-Combo id. Model MCH. Installation and Operation Instructions. Induced Draft Residential Gas-Fired Space/Water Heater

Mini-Combo id. Model MCH. Installation and Operation Instructions. Induced Draft Residential Gas-Fired Space/Water Heater Installation and Operation Instructions Document 2101B Installation and Operation Instructions for Mini-Combo id Model MCH Induced Draft esidential Gas-Fired Space/Water Heater Note: This document is to

More information

TECHNICAL GUIDE AFFINITY MODELS: PS9*UP GAS-FIRED CONDENSING / HIGH EFFICIENCY UPFLOW SINGLE STAGE FURNACES 92% TO 94% AFUE

TECHNICAL GUIDE AFFINITY MODELS: PS9*UP GAS-FIRED CONDENSING / HIGH EFFICIENCY UPFLOW SINGLE STAGE FURNACES 92% TO 94% AFUE TEHNIAL UIDE AFFINIT MODELS: PS9*UP AS-FIED ONDENSIN / HIH EFFIIEN UPFLO SINLE STAE FUNAES 92% TO 94% AFUE NATUAL AS 40-135 MBH INPUT EFFIIEN ATIN ETIFIED ISO 9001 ertified Quality Management System Due

More information

Installation Instructions

Installation Instructions Installation Instructions THERMAL EXPANSION VALVE (TXV) KIT FOR HEAT PUMP AND AIR CONDITIONING SAFETY INFORMATION IMPORTANT: Please read all instructions before servicing this equipment. Pay attention

More information

M3RL Series TECHNICAL SPECIFICATIONS. FEATURES and BENEFITS. High Efficiency / Direct Vent Condensing Downflow Gas Furnace

M3RL Series TECHNICAL SPECIFICATIONS. FEATURES and BENEFITS. High Efficiency / Direct Vent Condensing Downflow Gas Furnace TECHNICAL SPECIFICATIONS M3RL Series High Efficiency / Direct Vent Condensing Downflow Gas Furnace Induced Draft - 90+ AFUE Input 60,000 & 80,000 Btuh The high efficiency downflow gas furnace is especially

More information

Operator: Save these instructions for future use!

Operator: Save these instructions for future use! 50V64-743 Integrated Furnace Control for Furnaces with Variable Fan Speed INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS C7BA Series Split System Indoor Cased Coils IMPORTANT ATTENTION INSTALLERS: It is your responsibility to know this product better than your customer. This includes being able

More information

Operator: Save these instructions for future use!

Operator: Save these instructions for future use! 50A65-843 Universal Integrated Furnace Control INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTUCTIONS Models EBV 2-5 Ton Use ONL factory listed electric heaters. Variable Speed Safety Labeling and Signal ords Danger, arning and Caution The signal words DANGE, ANING and CAU- TION

More information

Smart-Wall TV Kit - Installation & Operation Instructions -

Smart-Wall TV Kit - Installation & Operation Instructions - If any parts are missing or damaged, contact your Dealer before starting installation. DO NOT install a damaged kit. Be sure to also reference the appliance Installers Guide. Approvals The flexible duct

More information

21D83M-843 Integrated Single Stage Furnace Control Replacement Kit INSTALLATION INSTRUCTIONS

21D83M-843 Integrated Single Stage Furnace Control Replacement Kit INSTALLATION INSTRUCTIONS 21D83M-843 Integrated Single Stage Furnace Control Replacement Kit INSTALLATION INSTRUCTIONS FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE

More information

TECHNICAL GUIDE MODELS: GY9F*UP GAS-FIRED CONDENSING / HIGH EFFICIENCY UPFLOW FURNACES 95% AFUE DESCRIPTION WARRANTY FEATURES YTG-B-0907

TECHNICAL GUIDE MODELS: GY9F*UP GAS-FIRED CONDENSING / HIGH EFFICIENCY UPFLOW FURNACES 95% AFUE DESCRIPTION WARRANTY FEATURES YTG-B-0907 TEHNIAL UIDE MODELS: 9F*UP AS-FIED ONDENSIN / HIH EFFIIEN UPFLO FUNAES 95% AFUE NATUAL AS 48-96 MBH INPUT EFFIIEN ATIN ETIFIED ISO 9001 ertified Quality Management System DESIPTION These ategory IV, highly

More information

Installation Instructions P/N

Installation Instructions P/N IM2 eplacement Kit For FK4A ancels: IIK FK4A-2-2 IIK FK4A-2-3 6-1 Installation Instructions P/N 32981-752 NTE: ead the entire instruction manual before starting the installation. SAFETY NSIDEATINS Improper

More information

Operator: Save these instructions for future use!

Operator: Save these instructions for future use! WHITE-RODGERS 50A55-474 & 50A55-571 Integrated Furnace Controls INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE

More information

TECHNICAL GUIDE. AFFINITY MODELS: PS8*DH GAS-FIRED HIGH EFFICIENCY SINGLE STAGE DOWNFLOW/HORIZONTAL FURNACES STANDARD & Low NOx DESCRIPTION WARRANTY

TECHNICAL GUIDE. AFFINITY MODELS: PS8*DH GAS-FIRED HIGH EFFICIENCY SINGLE STAGE DOWNFLOW/HORIZONTAL FURNACES STANDARD & Low NOx DESCRIPTION WARRANTY TEHNIAL UIDE AFFINIT MODELS: PS8*DH AS-FIED HIH EFFIIEN SINLE STAE DONFLO/HOIZONTAL FUNAES STANDAD & Low NOx NATUAL AS 40-130 MBH INPUT EFFIIEN ATIN ETIFIED DESIPTION These high efficiency, downflow/horizontal

More information

DDNECNJ SEQUENCE OF OPERATION This sequence assumes employment of a single enthalpy economizer using a two stage thermostat.

DDNECNJ SEQUENCE OF OPERATION This sequence assumes employment of a single enthalpy economizer using a two stage thermostat. -7-00 -7- (fax) Buschong, Houston, TX 770 www.mcdanielmetals.com DDNENJ00 DOWNFLOW JADE EONOMIZE FITS DAIKIN D00-0, DH00-0, D00-0 to cool the space. (o to step.). Outdoor air dampers open to minimum position

More information

TECHNICAL GUIDE SINGLE PIECE VARIABLE SPEED AIR HANDLERS DESCRIPTION FOR USE WITH SPLIT-SYSTEM COOLING & HEAT PUMPS FEATURE MODELS: AVG24 THRU 60*(C)

TECHNICAL GUIDE SINGLE PIECE VARIABLE SPEED AIR HANDLERS DESCRIPTION FOR USE WITH SPLIT-SYSTEM COOLING & HEAT PUMPS FEATURE MODELS: AVG24 THRU 60*(C) TEHNIAL UIDE SINLE PIEE VARIABLE SPEED AIR HANDLERS FOR USE WITH SPLIT-SYSTEM OOLIN & HEAT PUMPS MODELS: AV24 THRU 60*() DESRIPTION The Air Handler line offers the ultimate in comfort, sound and application

More information

E3EH-xxx-H Series E3EB-xxx-H Series

E3EH-xxx-H Series E3EB-xxx-H Series TECHNICAL SPECIFICATIONS E3EH-xxx-H Series E3EB-xxx-H Series Downflow, Upflow Electric Furnaces The E3 Series furnace is designed for all sizes of manufactured and modular homes. These units incorporate

More information

WARNING IMPORTANT DIAGNOSTIC TESTS ACTIVATING THE DIAGNOSTIC TEST MODE DIAGNOSTIC GUIDE. Electrostatic Discharge (ESD) Sensitive Electronics

WARNING IMPORTANT DIAGNOSTIC TESTS ACTIVATING THE DIAGNOSTIC TEST MODE DIAGNOSTIC GUIDE. Electrostatic Discharge (ESD) Sensitive Electronics TECH SHEET - DO NOT DISCAD PAGE ANING Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS C7BA & C7BH Series Split System Indoor Cased Coils INSTALLATION INSTRUCTIONS IMPORTANT It is your responsibility to know this product better than your customer. This includes being able to install the

More information

Energy Manager INSTALLATION INSTRUCTIONS. Keep these instructions with the boiler at all times for future reference

Energy Manager INSTALLATION INSTRUCTIONS. Keep these instructions with the boiler at all times for future reference INSTALLATION INSTRUCTIONS Energy Manager Keep these instructions with the boiler at all times for future reference BOYERTOWN FURNACE CO. PO Box 100 BOYERTOWN, PA 19512 1-610-369-1450 www.boyertownfurnace.com

More information

TECHNICAL GUIDE MODELS: GM9S*UP GAS-FIRED CONDENSING / HIGH EFFICIENCY UPFLOW FURNACES 92% TO 94% AFUE DESCRIPTION WARRANTY FEATURES BTG-A-0407

TECHNICAL GUIDE MODELS: GM9S*UP GAS-FIRED CONDENSING / HIGH EFFICIENCY UPFLOW FURNACES 92% TO 94% AFUE DESCRIPTION WARRANTY FEATURES BTG-A-0407 TEHNIAL UIDE MODELS: M9S*UP AS-FIED ONDENSIN / HIH EFFIIEN UPFLO FUNAES 92% TO 94% AFUE NATUAL AS 40-135 MBH INPUT EFFIIEN ATIN ETIFIED ISO 9001 ertified Quality Management System DESIPTION These ategory

More information

TECH SHEET - DO NOT DISCARD PAGE 1 DIAGNOSTIC TESTS. Press/hold 2-5 seconds. DIAGNOSTIC: Unsuccessful Entry. DIAGNOSTIC: Saved Fault Codes

TECH SHEET - DO NOT DISCARD PAGE 1 DIAGNOSTIC TESTS. Press/hold 2-5 seconds. DIAGNOSTIC: Unsuccessful Entry. DIAGNOSTIC: Saved Fault Codes TECH SHEET - DO NOT DISCAD PAGE ANING Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock.

More information

Installation instructions for Plenum-mounted add-on electric heaters MODEL TU. September 2016 Version 7

Installation instructions for Plenum-mounted add-on electric heaters MODEL TU. September 2016 Version 7 Installation instructions for Plenum-mounted add-on electric heaters MODEL TU September 2016 Version 7 THERMOLEC PLENUM HEATER MODEL TU BEFORE YOU START -GENERAL SAFETY AND INSTALLATION PRECAUTIONS Please

More information

G60DFV(X) WARNING. WARNING Sharp edges. Be careful when servicing unit to avoid sharp edges which may result in personal injury. Service Literature

G60DFV(X) WARNING. WARNING Sharp edges. Be careful when servicing unit to avoid sharp edges which may result in personal injury. Service Literature Service Literature Corp. 0211 L3 Revised 09 2006 G60DFV(X) G60DFV(X) SERIES UNITS G60DFV series units are mid efficiency gas furnaces used for downflow applications only, manufactured with Lennox Duralok

More information

Operator: Save these instructions for future use!

Operator: Save these instructions for future use! 031-01284-000/50A55-241 Integrated Furnace Control INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR

More information

BCE4 PRODUCT SPECIFICATIONS ENHANCED AIR HANDLER WITH VARIABLE SPEED APPLICATION INSTALLATION CABINET COMPONENTS CONTROLS WARRANTY

BCE4 PRODUCT SPECIFICATIONS ENHANCED AIR HANDLER WITH VARIABLE SPEED APPLICATION INSTALLATION CABINET COMPONENTS CONTROLS WARRANTY PRODUCT SPECIFICATIONS ENHANCED AIR HANDLER WITH VARIABLE SPEED FORM NO. -100 (11/2015) APPLICATION 2-5 ton sizes Upflow, horizontal, and downflow capable Sequenced for demand management External access

More information

DAVE LENNOX SIGNATURE COLLECTION Lo-Boy - Variable Speed Blower

DAVE LENNOX SIGNATURE COLLECTION Lo-Boy - Variable Speed Blower PRODUCT SPECIFICATIONS OIL FURNACES sl085bv DAVE LENNOX SIGNATURE COLLECTION Lo-Boy - Variable Speed Blower Bulletin No. 0677 August 05 Supersedes September 04 AFUE - Up to 87% Heating Input - 79,000 to

More information

ACNF Series Ceiling-Mount Air Handlers 1½ to 2½ Tons

ACNF Series Ceiling-Mount Air Handlers 1½ to 2½ Tons ANF Series eiling-mount Air Handlers 1½ to 2½ Tons Standard Features Suitable for use with refrigerants R-410A and R-22 heck flowrater for heat pump and cooling-only applications All-Aluminum tube/aluminum

More information