THE HYBRID WATER PURIFIER USER MANUAL

Transcription

1 THE HYBRID WATER PURIFIER USER MANUAL Congratulations on the purchase of your water purifier F-FWEG1-M-A-NT-**-*** Warning: Boil the water should the purification unit fail

2 DECLARATION Waterlogic International Ltd 1. If any abnormal case occurs, firstly unplug the appliance. 2. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. 3. Children should be supervised to ensure that they do not play with the appliance. 4. This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years. 5. Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. 6. Children must not play with the appliance. 7. If the supply cord or the detachable cord sets are damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 8. WARNING: fill with potable water only. 9. The appliance is to be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA. 10. This appliance is intended to be used in household and similar applications such as staff kitchen areas in shops, offices and other working environments; farm houses and by clients in hotels, motels and other residential type environments; bed and breakfast type environments; catering and similar non-retail applications. 11. This appliance contains a UV-C emitter (UV lamp) 12. Unintended use of the appliance or damage to the housing may result in the escape of dangerous UV-C radiation. UV-C radiation may, even in little doses, cause harm to the eyes and skin. 13. Appliances that are obviously damaged must not be operated. 14. Read the maintenance instructions before opening the appliance. 15. The appliance must be disconnected from the supply before replacing the UV lamp. 16. The UV lamp must be replaced at 12 month intervals or when necessary. If the unit is placed in a high use area, the UV lamp will need to be replaced more frequently. The quartz spiral can be cleaned by using an ultrasonic bath if needed. 17. WARNING: Do not operate the UV lamp when it is removed from the appliance enclosure. 3

3 IMPORTANT CAUTIONS To enjoy the reassurance of delicious, refreshing, healthy and hygienic drinking water, please follow the instructions contained in this document. Please retain these instructions for future reference in a safe and convenient place. This appliance is for use with potable drinking water only. Never use this appliance with unknown or unsafe sources Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance Do not use this appliance if the mains cord, plug or other parts are damaged Do not allow children to use the appliance without supervision Never leave the appliance unattended when water is being dispensed Never use the appliance if there is any visible damage to the appliance or the power cord The reservoir may be stored in the fridge if you would like to dispense cold water from the appliance Unplug the appliance before removing any part of the appliance for servicing This appliance is for indoor use only Never immerse the appliance in water or spray any liquid onto the outside of the appliance Do not overfill the reservoir When re-inserting any screws make sure that they are hand tightened only Only use authorised parts from the manufacturer to repair and service the unit Only use Waterlogic UV lamps and filters with the appliance, failure to do so will void the warranty When the appliance has not been used for 3 hours or is idle, the UV lamp will turn on for 60 seconds at 3 hour intervals Make sure the appliance is placed on a flat, level, dry and secure surface Read all instructions contained in this user manual prior to using this appliance When removing the water reservoir from the appliance, place one hand on top of the appliance securing it while using your other hand to remove the reservoir Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cyst The system and installation shall comply with applicable state and local regulations The system must be supplied with cold or ambient water DECLARATION The UV lamp in our appliance conforms to the applicable provisions of the Code of Federal Regulations (CFR) requirements including, Title 21, Chapter 1, Subchapter J, Radiological Health DÉCLARATION La lampe UV dans notre appareil est conforme aux dispositions applicables du Code of Federal Regulations (CFR), y compris à ses exigences du titre 21, chapitre 1, sous-chapitre J «Radiological Health» Power Supply: Volt / 50Hz & 120 Volt / 60Hz Power consumption: 0.07 Kwh Rated service flow: 0.9 lpm with a new filter Operating Temperature: 2 C - 32 C Reservoir capacity: 1.5 Liters 1. Only trained competent technicians should carry out repairs on the appliance 2. Packing materials could present a trip hazard. Keep them off the floor and out of reach of infants and small children 3. Avoid the power plug and cord contacting water or moisture. Should this happen, unplug the lead from the power source and discontinue using the appliance until deemed safe to do so 4. Do not handle or move the appliance when the reservoir contains water 5. GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an appliance-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances MISE A LA TERRE Cet appareil doit être mis à la terre. En cas de dysfonctionnement ou de panne, la terre réduira le risque de choc électrique en fournissant un chemin de moindre résistance pour le courant électrique. Cet appareil est équipé d un cordon muni d un conducteur appareil à la terre et une fiche de terre. La fiche doit être branchée dans une prise appropriée qui est installée et mise à la terre conformément à tous les codes et règlements locaux 6. Connect only to a circuit that is protected by a ground-fault circuit-interrupter (GFCI) Connecter uniquement à un circuit protégé par une mise à la un défaut à la terre de circuit (GFCI) 7. WARNING Improper connection of the appliance-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified technician AVERTISSEMENT Un mauvais raccordement du conducteur de mise à la terre de l appareil peut entraîner un risque de choc électrique. Vérifier avec un électricien qualifié ou un technicien agréée représentant de service si vous avez des doutes quant à la mise à la terre de l appareil est correctement mis à la terre. Ne pas modifier la fiche fournie avec l appareil ; si elle n entre pas dans la prise, faites installer une prise adéquate par un technicien qualifié 8. Warning Isolate power supply before removing cover 9. This Class A system conforms to NSF Standard 55 and P231 for the disinfection of micro biologically contaminated water that meets all other public health standards. The system is not intended to convert wastewater or raw sewage into drinking water. The system is intended to be installed on visually clear water 5

4 1. BOX CONTENTS 2. SET-UP GUIDE 1.1 Remove the HYBRID from the box. To avoid damaging the appliance DO NOT use any sharp object to open the box 1.2 Please check the contents of the box and make sure that all items are present A B C D HYBRID UNIT RESERVOIR LID RESERVOIR DISPENSING BUTTON IMPORTANT 2.1 Check the unit for any damage, if the appliance is damaged then please return to the place of purchase 1.3 The UV lamp and filter are pre-installed and ready to use. E F FAUCET DRIP TRAY 2.2 Remove the protective cover from the end of the Firewall spiral D B E 2.3 Insert the plug into the mains socket. When the mains power is switched on the appliance will automatically go through a self check/test and once this is complete the button will turn blue A F C 2.4 Remove the water reservoir from the main body of the appliance and remove the lid from the reservoir If any of the items are missing please contact customer service 7

5 2.5 Rinse the reservoir and then fill the reservoir from a potable water source. Do not overfill the reservoir. Re-fit the reservoir cover 2.7 Place a glass or large container under the dispense area and touch the dispense button to operate the unit, and touch again to stop the appliance. Allow water to run through the unit until the reservoir has been emptied. Refer to section 5 in this manual for the button functions Note: Do not consume the water until step 2.8 has been completed. The first 3-5 litres of water dispensed may contain some fine, black carbon particles. Carbon is a natural, organic material made from coconut shell, and is harmless to your health. Clear water should be noticed after flushing through 3 to 5 litres of water (2 to 3 full reservoirs). Do not allow the water level in the reservoir to drop below the minimum fill line, as when the reservoir is completely empty the pump will begin to suck in air and make bubbling noises Re-fit the reservoir to the appliance making sure it is firmly fitted 2.8 Repeat steps three to four times (3x - 4x). This will flush the carbon from the new filter 2.9 Once step 2.8 has been completed you can drink purified, healthy and safe water from your appliance During the first week of use and after every filter change you may notice water dripping out of the dispensing-nozzle for several seconds after the unit has stopped dispensing. This is normal, and will stop after several days of use. Note: For a cold refreshing drink the reservoir may be stored full of water in the fridge x3-4 9

6 3. UV BULB AND FILTER REPLACEMENT IMPORTANT NOTE ON HYBRID SERVICING To ensure the highest quality of water and compliance with NSF Protocol P231, the Hybrid model that is on sale in the US includes a 1 micron carbon block filter with cyst & lead reduction capabilities, and a 13 Watt UV-C lamp, that require periodic replacement (annualy, in most cases) - please refer to section 3 of the Hybrid User Manual or section 2 of the Hybrid Servicing Manual for instructions on how to service the machine. Please ensure you purchase only original Waterlogic replacement parts sold in the US. PART NUMBERS: MODEL NUMBER: F-FWEG1-M-A-NT-XX-YYY This system, when used with FT-0006-L00-XXX 1 micron CBC cyst and Lead reduction filter, has been tested and certified by WQA according to NSF/ANSI 42, NSF/ANSI 53, NSF/ANSI 55 Class A and NSF/ANSI P231 as verified and substantiated by test data. The Hybrid Pure Kit which is sold in the US: K-FU-E0C1L XXX Carbon Block Filter included in the Hybrid Pure Kit: FT-0006-L00-XXX UV Lamp included in the Hybrid Pure Kit: CT-2090-C Note: Please note the letters XXX can be any 3 letters Where to buy? the Hybrid Pure Kit is available from the retailer where you purchased your machine, call us if you want more details. CT-2090-C THIS PRODUCT IS A HIGH PERFORMANCE WATER PURIFIER, KEEPING IT IN GOOD WORKING ORDER WILL PROVIDE THE REASSURANCE OF TRULY GREAT DRINKING WATER PLEASE READ AND NOTE SECTION 6 INDICATION & WARNING ICONS IMPORTANT - UNPLUG THE APPLIANCE FROM THE MAINS BEFORE REPLACING THE UV LAMP OR FILTER 3.1 Remove the water reservoir from the main body of the appliance. This can be cleaned with a light solution of dishwashing liquid. Never use abrasive chemicals or materials to clean the reservoir as this could scratch and deface the product 3.2 Remove the two screws that hold the top cover in place. You will need to use a screwdriver to carry out step 3.2 The UV Bulb and Filter must be replaced every 12 months to ensure that your appliance is dispensing the highest quality drinking water. Replacement Parts: Please make sure you use only original Waterlogic replacement parts. If you are not sure which replacement parts to use, please consult with your local Waterlogic retailer or distributor CT-2090-C FT-0006-L00-XXX Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. 11

7 3.3 Remove the top cover from the unit by slightly pushing it back and then lifting it up 3.6 Insert the new UV lamp while holding the white end caps only. Insert the UV lamp as shown in the illustration and push it all the way down until it cannot go any further CAUTION :- Do not use force when removing and inserting the UV lamp as you may damage internal parts :- Do not touch the UV lamp glass surface with your fingers as this will affect the performance of the UV lamp 3.4 Disconnect the UV lamp connector by holding it and pressing in the clip on the connector and pulling it up 3.7 Re-connect the UV lamp connector making sure the connectors are lined up correctly as they will only fit together when correctly aligned 3.5 To remove the UV lamp firmly pull it up and out. Do not pull the lamp out at an angle as it may break or damage the internal parts of the appliance Note: The UV lamp must be disposed of correctly and must not be disposed of with normal household waste 3.8 To remove the Filter, do the following: 1. Rotate the red rotating lever so that it is parallel with the side panel 2. Insert your finger into the round hole of the lever, and pull the lever up to the vertical position 3. Pull the lever straight up to remove the Filter assembly (Slight force may be required. Support the unit with your other hand while pulling the filter out). Note: Dispose of the filter following your local guidelines

8 4. BUTTON FUNCTIONS 3.9 Fit the new filter assembly into the appliance as follows: 1. Insert the filter assembly back into its cradle, aligning the two male spigots with the female holes in the cradle 2. Push firmly until the filter sits snugly and is flush inside the cradle and with the cradle top surface When the appliance is in standby mode the button will be blue but when it is touched it will turn green and water will be dispensed Note: If the button is not touched within 2 minutes of being activated then it will automatically stop the flow of water and turn the pump off. 3. Lock the filter by closing the locking lever until it clicks into place 4. Rotate the red rotating lever back into the LOCK position 3.10 Re-fit the top cover, making sure the front is attached first. If the top cover is not fitted correctly the unit will not switch on Hint: Fit the top cover making sure the front is pushed in place first and then push the back end with the screws down to give a snug fit Touch to STOP dispensing water. When you touch the button to stop water being dispensed the button will change colour from green to blue Note: After one minute the product is in a stand-by mode it goes in an energy saving mode as the UV is off; when the product is in this condition, there will be a 2 second delay before the water is dispensed after the dispense button is touched so as to activate the UV lamp and purify the water Re-fit the two screws that hold the lid down using a screwdriver. Caution: The screws should be hand tightened, do not over tighten Insert the plug into the mains socket Press and hold the dispense button for 10 seconds until you hear a beep as this will rest the filter timer Note: Place a cup or container under the dispense area before carrying out step The filter now needs to be flushed, follow step 2.3 through to

9 5. INDICATION AND WARNING ICONS 6. PERFORMANCE DATA SHEET Your product has been designed and internationally certified to the highest standards of water purification, and guarantees at all times, to dispense the purest and cleanest water. The self monitoring system will warn you of any potential risks, by way of 3 possible alarms. 5.1 Once the Filter has reached 95% of its life, the Filter icon will flash as a reminder, and continue to flash until the filter has been replaced as per 5.2 below. During this time, your machine will continue to dispense water, until 5.2 below has been reached WATERLOGIC HYBRID Model Name: F-FWEG1-M-A-NT-XX-YYY Waterlogic HYBRID with CYST/LEAD Removal Filter FT-0006-L00-XXX XX: color code YYY(-XXX): customer code IMPORTANT NOTICE MANUFACTURED BY QINGDAO WATERLOGIC MANUFACTURING CO., LTD. No. 10 Jinling Road, Jinling Industrial Zone, Chengyang District, Qingdao China Tel ; Fax This system, when used with FT-0006-L00-XXX 1 micron CBC cyst and reduction filter, has been tested according to NSF/ANSI 42, NSF/ANSI 53, NSF/ANSI 55 Class A and NSF/ANSI P231 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42, NSF/ANSI 53, NSF/ANSI 55 Class A and NSF/ANSI P231. While testing was conducted under standard laboratory conditions, actual performance may vary. 5.2 After a 12 month period, both the UV Bulb and Filter must be replaced to ensure optimal water purification. Both the UV Icon and Filter Icon will alarm 20 times and flash alternately. When this occurs, no water will be dispensed, until the Filter and UV Bulb have both been replaced and the machine reset (to do this you will need to follow steps 3.5 to 3.13 ) FILTER PERFORMANCE DATA TABLE Parameter Minumum % reduction requirement / Max effluent concentration Average Influent Challenge Effluent Average Effluent Maximum Percent Reduction Average Percent Reduction Minimum Chlorine >=50% reduction 1.90 ppm 0.02 mg/l 0.02 mg/l 98.9% 98.9% Cyst Lead (Low ph = 6.5) >=99.95% reduction 120,000 oocyst/l 38 oocyst/l < 50 oocyst/l 99.99% 99.97% < 10 ug/l 144 ug/l 0.49 ug/l 1.60 ug/l 99.7% 98.9% 5.3 In the unlikely event that the UV bulb should fail the UV icon will flash and alarm 20 times. No water will be dispensed until steps 3.1 to 3.7 and steps 3.10, 3.11 are completed Lead (High ph = 8.5) Particulate Class I (>=0.5 um to <1 um) < 10 ug/l 140 ug/l 1.47 ug/l 7.50 ug/l 98.9% 94.6% >=85% reduction >/=10,000 particles/ml 288 particles/ml 704 particles/ml 97.9% 94.9% Tested using flow rate = 0.5 GPM; pressure = 60 psi; ph = 7.5 ± 0.5; temp. = 20 ± 1.0 C. UV PERFORMANCE DATA TABLE Parameter Bacteria (R.terrogema) Virus (MS2)* Log Reduction Average 7.4 Log 3.16 Log Note: 2 Log reduction of MS2 is equivalent to 4 Log reduction of Poliovirus or Rotavirus Tested using flow rate = 0.5 GPM; pressure = 60 psi; ph = 7.5 ± 0.5; temp. = 20 ± 1.0 C. 17

10 OPERATING SPECIFICATIONS Filter Capacity Lead Capacity Maximum Flow Rate Maximum Feed water temp Minimum Feed water temp Maximum Working Pressure Electrical Requirements GENERAL INSTALLATION/OPERATION/ MAINTENANCE REQUIREMENTS This appliance is for use with potable drinking water only. Never use this appliance with unknown or unsafe sources. Flush new units with 5 Liters of water prior to use. Replace filter cartridge when rated capacity is reached, or every 12 months, or when flow becomes too slow. Replace UV lamps every 12 months, or when the UV intensity is lower than required. Install in compliance with state and local laws and regulations. SPECIAL NOTICES The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. System certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. 2,500 Gallons / 9,464 Liters 1,250 Gallons /4,732 Liters 0.42 GPM / 1.6 LPM 32 C (90 F) 2 C (35 F) N/A EU: V 50Hz; USA: 120V 60Hz; Maximum 2.0 amps This Class A system conforms to NSF/ANSI 55 for the disinfection of microbiologically contaminated water that meets all other public health standards. The system is not intended to convert wastewater or raw sewage to drinking water. This system is intended to be installed on visually clear water. NSF/ANSI 55 defines waste water to include human and/or animal body waste, toilet paper, and any other material Intended to be deposited in a receptacle designed to receive urine and/or feces (blackwaste); and other waste materials deposited in plumbing fixtures (greywaste). WARRANTY INFORMATION Waterlogic International (Waterlogic) warrants that the products delivered will be free from any defects in workmanship or materials. Further, the warranty provided herein applies, only when used within the products specifications and service life, from the date of installation, beyond which time or use Waterlogic is absolved of any and all liability for any use of the product. In the event of defect or non-conformity, buyer shall promptly notify Waterlogic in writing, supplying proof of purchase dates, installation dates, and will protect and retain the products for investigation, or Waterlogic is absolved of any and all liability for any use of the product. There are no other warranties, either merchantability or fitness, either expressed or implied. FOR IOWA ONLY The manufactures PDS shall be given to the buyer by the seller and shall be signed and dated by the buyer and the seller prior to the consummation of the sales of the water treatment system and retained on file by the seller for a minimum of two years. Seller Date Buyer Date 7. TROUBLESHOOTING If there is no water being dispensed: Check that the unit is plugged in and switched on at the mains wall socket Check that the reservoir is fitted correctly Check that there is water in the reservoir Make sure that the top cover is fitted correctly 8. CLEANING Make sure the button is illuminated solid blue. Should the appliance be faulty please either return the product in its original packaging with proof of purchase or contact the local customer service centre. Should there be no response from the button remove the power cord and wait 10 seconds before plugging it back in. This will reset the appliance. It is recommended that you maintain your appliance by cleaning it on a regular basis. The appliance can be cleaned using a damp lint free cloth. Never use any alcohol or alcohol based chemicals or abrasive materials on any part of the product. 9. STORAGE Never store the appliance with water in the reservoir and always store it the correct way up in a dry environment. If the unit has not been used for more than 3 months it is recommended that you flush several liters of water through it before drinking. Always ensure you replace your filter every year even if the device is not being used regularly. 19

11 10. SAFETY Do not touch or look directly into the faucet Do not handle or lift the appliance by holding the reservoir Only authorised trained technicians may carry out repairs on this appliance The user may only replace the filter and UV lamp The filter and UV lamp must be replaced every 12 months. Never use any chemicals or abrasive materials on any part of the product Should a fault occur on the appliance always unplug it from the mains power supply If the power lead is damaged in any way it must be replaced by an authorised dealer or qualified person This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance 11. CERTIFICATION The appliance has attained and complies with the following certifications and directives: CE, NSF 42 & 53, NSF 55a, NSF P231, RoHS, REACH 12. DISPOSAL Do not dispose of the appliance with normal household waste, hand it in at an official collection point for recycling. By doing this you are doing your bit for the environment. WEEE compliance Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. Manufactured by Qingdao Waterlogic Manufacturing Co., Ltd No 10 Jinling Road, Jinling Industrial Zone, Chengyang District, Qingdao, , Shandong, P.R. CHINA TEL: v03 20