Nilfisk Inc winnetka Avenue North Minneapolis, MN Rev.05(15-12)

Transcription

1 Nilfisk Inc winnetka Avenue North Minneapolis, MN Rev.05(15-12)

2 TABLE OF CONTENTS Machine Components 3 Safety Precautions 4 Machine Set Up 5 Machine Operation 5-6 Machine Maintenance & Storage 6-7 Troubleshooting 8 Parts Lists 9-17 Wiring Diagram 18 2

3 MACHINE COMPONENTS ) Vacuum / pump on/off switch 2) Recovery tank lid 3) Solution tank fill port 4) Pipe 5) Accessory tool solution hookup 6) Drain hose 3

4 SAFETY PRECAUTIONS GROUNDING INSTRUCTIONS General This carped extraction machine shall be grounded while in use to protect the operator from electric shock. The machine is provided with a three-contact grounding type attachment plug to fit the proper grounding type receptacle. The green (or green & yellow) conductor in the cord is the grounding wire. Never connect this wire to other than the grounding pin of the attachment plug. This machine is for use on a nominal 120- volt circuit and has a grounding plug that resembles the plug illustrated in figure below. Make sure that the machine is connected to an outlet having the same configuration as the plug. No adapter should be used with this machine. This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only recommended accessories. All operators shall read, understand and exercise the following safety precautions: 1) Do not operate machine: - Unless trained and authorized - Unless you have read and understand operators manual - In flammable or explosive areas. - With damaged or modified cord or plug. - If not in proper operating condition. - In outdoor areas. - In standing water. - Without filters in place. - With the use of unapproved extension cords. 2) Before operating machine: - Make sure all safety devices are in place and operate properly. 3) When using machine: - Mix and handle any chemicals according to manufacturer s recommendations - Do not run machine over cord. - Do not pull machine by cord or plug. - Do not pull cord around sharp edges or corners. - Do not unplug by pulling on the cord. - Do not stretch cord. - Do not handle plug with wet hands. - Keep cord away from heated surfaces. - Do not pick up flammable materials or reactive metals. - Report machine damage or faulty operation immediately. 4) Before leaving or servicing machine: - Turn off machine. - Unplug power cord from outlet. 5) When servicing machine: - Unplug cord from outlet. - Use manufacturer supplied or approved replacement parts. - Avoid moving parts. Don t wear loose clothing. 4

5 SLIDER EXTRACTOR SETUP!!! Read operators manual thoroughly prior to operating or servicing this machine!!! Carefully check the shipping carton for signs of damage. Report any carton damage to carrier immediately. Check carton contents to ensure carton is complete. Contact your Viper distributor if anything is missing. Contents: Carpet Extractor Short bleeder vacuum hose 50 extension power cable Vacuum and solution hoses!!! Read operators manual thoroughly prior to operating or servicing this machine!!! 1) Using a hose or bucket, fill tank with a maximum of 10 gallons of hot water. 2) Add distributor recommended cleaning solution!!! Do not use flammable liquids or operate machine in or near flammable liquids or vapors!!! 3) Connect the supplied extension power cable to the machine. Plug cord into a grounded wall outlet. (see grounding instructions) 4) Attach vacuum and solution hoses to appropriate connections on the machine and your wand.. As you do this, always inspect hoses for cracks or fraying. Do not use if hose are cracked of frayed. MACHINE OPERATION PRIOR TO EXTRACTING CARPETS 1) Inspect power cable and extension cable for damage. Replace cable if damage is found. 2) Vacuum carpet to remove debris prior to extracting carpet. CARPET EXTRACTING 1) Turn on vacuum / pump switch. 2) To release spray, simply pull back on your wand trigger. OPERATING HINTS 1) Work away from power outlet and power cable in order to avoid damage to the power cable. 2) Continually check for foam buildup in recovery tank. Use a distributor recommended foam control solution. NOTE: Excessive foam buildup will not activate the float shut-off and may cause damage to the vacuum motor. 3) Repeat extraction path on heavily soiled areas. 4) When recover of the dirty solution ends, or the solution tank is empty, you must drain the recovery tank. (see TANK DRAINING) USE OF ACCESSORY TOOLS NOTE: Prior to cleaning upholstery, be sure to read cleaning instructions provided by the manufacturer. 1) Attach vacuum and solution hoses to appropriate connections on the machine. 2) Connect (optional) accessory tool to solution and vacuum hoses. 5

6 3) Turn on vacuum / pump switch. 4) Operate accessory tools as needed. 5) When cleaning is completed, relieve water pressure from solution lines by turning off vacuum / pump switch and then squeeze trigger for 4 seconds. DRAINING TANKS DRAINING SOLUTION TANK 1) Connect the bleeder vacuum hose (included with machine) to the vacuum inlet. 2) Remove the solution tank filter at the fill area and place end of bleeder hose into the bottom of the tank. 3) Turn on vacuum / pump switch & vacuum out the remaining solution. DRAINING RECOVERY TANK 1) Turn off machine, unplug and remove power cable. 2) Unhook drain hose off the back of the machine and remove drain hose stopper. 3) Drain dirty solution into floor drain. 4) Replace drain hose stopper and reattach hose to back of machine. MACHINE MAINTENANCE To keep the machine performing well for many years, please follow the following maintenance procedures.!!! Always confirm that the machine is unplugged prior to performing any maintenance or repairs!!! DAILY MAINTENANCE 1) When cleaning operation is complete for the day, drain and rinse the recovery tank thoroughly with clean water. 2) Remove remaining solution from solution tank. 3) Remove float shut-off (ping pong ball in cage) from recovery tank and clean with water. 4) The filter located in the solution tank need to checked and cleaned when dirty in order for it to properly filter debris from the solution tank. if the filter is missing or damaged it must be replaced before the machine is used. 5) Clean machine with a nonabrasive cleaner. 6) Inspect power cable for any damage. Replace if necessary. MONTHLY MAINTENANCE 1) Flush pump & plumbing with an acetic acid solution to dissolve any chemical buildup. Mixing Instructions: a) Premix 16 oz. or an acetic acid solution with 2 gallons of water and pour into solution tank. b) Attach solution hose and wand to machine. c) Turn vacuum / pump switch on. 6

7 d) Hold the wand trigger open and direct the flow of solution into the solution tank so that it can recirculate through the entire solution system. After 5 minutes. Remove wand from solution tank and completely empty solution tank through the bleeder vacuum hose and drain into the appropriate drain outlet. e) Fill solution tank with 3 gallons clean water and completely drain solution tank by holding open the wand trigger and draining into appropriate drain outlet. 2) Inspect machine for water leaks. 3) Lubricate wheels with a water resistance lubricant. 4) Check machine for loose or missing nuts, screw and bolts and replace as necessary. MACHINE STORAGE 1) Prior to storing the machine, ensure the solution and recovery tanks are clean and empty of any solution. 2) Store machine in upright position in a dry area, with the brush head off the floor. 3) Remove recovery tank clear lid to allow for air circulation. NOTE: If you are storing the machine in an area which can freeze, be sure both tanks and the solution plumbing are empty of all water and dry! 7

8 BASIC TROUBLESHOOTING PROBLEM CAUSE SOLUTION Machine doesn't work Not plugged in to power source Plug into a grounded outlet Faulty power cable Faulty extension power cable Replace with new extension power cable Solution pump not working Vacuum / pump switch not on Turn on switch Vacuum / pump switch faulty Faulty solution pump Vacuum motor not working Pump overheated Loose or broken wiring Vacuum / pump switch not on Vacuum / pump switch faulty Determine cause and allow 30 minutes for pump to cool Turn on switch Vacuum motor thermal overload tripped Check for obstruction and allow 30 minutes to cool Faulty vacuum motor Worn carbon brushes Loose or broken wiring Poor pick up Air leaking around clear recovery lid Ensure recovery lid is firmly tightened Clogged float shut-off Remove float shut-off and clean off debris Float shut-off is activated Drain recovery tank Loose drain hose stopper Ensure stopper is securely in place Loose vacuum hose connections Ensure vacuum hose connections are tight Defective vacuum hose Replace vacuum hose Loose vacuum hose cuffs Ensure cuffs are secure to the hose Uneven or no solution spray Solution tank is empty or low Fill solution tank Vacuum / pump switch not on Turn on switch Dirty or plugged spray tips Clean or replace spray tips Improper spray tip size or spray angle Worn spray tips Faulty solution pump Plugged solution tank filter Clean or replace filter Pinched or kinked solution hose Check for obstructions and kinks and reroute or replace if needed 8

9 9

10 PARTS LIST DIA NO PART NO DESCRIPTION NUMBER REQ'D 1 VV67161 CLEAR DOME, FRICTION FIT 1 2 VV67163 GASKET, CLEAR DOME 1 3 VA13477 SELF-TAPPING SCREW,ST4X VV67109 TUBE, ELBOW 1 5 VV67301 COUPLER 1 6 VV67302 GASKET, COUPLER 1 7 VV67108 ELBOW 1 8 VF81226 COUPLER, VACUUM HOSE 1 9 VV67706 DRAIN HOSE 1 10 VV VACUUM HOSE 1 11 VV10113 HOSE CLAMP, 2" 2 12 VV20509 SCREW, M5X10, SST 4 13 VV13601 WASHER, LOCK, SST, Ø VV50712 CLAMP, CORD 3 15 VV67503 SWITCH 1 16 VV66502 BLOCK, SWITCH 1 17 GV40239 COVER, SWITCH 2 18 VF14126 SCREW, HEX HEAD, M5X GV40215 CORD WRAP 1 20 VV67111 CLAMP, DRAIN HOSE 1 21 VV67501C SWITCH HOUSING 1 22 VF99008 STRAIN RELIEF 1 23 VV67507 CORD 1 24 VV67116 POWER CORD 1 25 VV67505 BUSHING, CORD, GT13032 WASHER, PLAIN, Ø6XØ16X VV13607 WASHER, LOCK, SST, Ø GT13056 SCREW, PAN HEAD, M6X VV67105 CONNECTOR 1 30 VV80128 HOSE BARB 1 31 VV80115 ELBOW, STREET, VV80125A NUT, COUPLING 1 33 VV20667 WASHER, LOCK, INTERNAL TOOTH 1 34 VV60509 GASKET, SOLUTION,INTAKE 1 35 VV20276 WASHER, PLAIN 1 36 VV80125 COUPLING 1 37 VV10411 STRAINER, LINE 1 38 VV67101 SOLUTION TANK 1 39 VF47035A LOGO 1 40 VV67107 FILTER 1 10

11 PARTS LIST DIA NO PART NO DESCRIPTION NUMBER REQ'D 41 VA13471 SCREW, ST5X VV67102 RECOVERY TANK 1 43 VF81504 FLOAT SHUT-OFF 1 44 VV67305 BEND 1 45 VV13664 WASHER,PLAIN, 4X 12X VF13491 SCREW, M4X12, SST 2 47 VV67162 RUBBER HINGE 1 48 VF81403 ELBOW, 90º, BRASS 1 49 VV67708 TUBING 1 50 VF82090 CLAMP(16-20) 1 51 VV67711 ELBOW, 90º, BRASS 1 52 VV67118 LABEL, RIGHT 1 53 VF80331 DECAL, WARNING 1 54 VV67119 LABEL, LEFT 1 55 VA20104A PLUG,DRAIN HOSE 1 11

12 12

13 PARTS LIST DIA NO PART NO DESCRIPTION NUMBER REQ'D 1 VV67605 PUMP,115V,100PSI 1 2 VV67601 MOUNTING FRAME,PUMP 1 3 VV80210 BEND,NYLON,PUMP 2 4 VV10114 CLAMP,HOSE,3/8" 4 5 VF81503 GASKET,VAC MOTOR 1 6 ZD63000A VAC MOTOR,3-STAGE,120V 1 7 GT13032 WASHER,SST,PLAIN,Ø6XØ16X VF13502 NUT,LOCK,M6 3 9 VF13521 NUT,SST,M VF81508 STUD 3 11 VV10113 CLAMP,HOSE, 2" 3 12 VV67152 EXHAUST HOSE,Ø VV67117 HOSE,SOLUTION 1 14 VV66115 HOSE,SPRAYING 1 15 VV80128 BARB,HOSE 1 16 VV66101 PIPE ASSY,VAC ELBOW 1 17 VV20274A WASHER,PLAIN,Ø14XØ32X VV20274 WASHER,PLAIN,Ø13.5XØ32X RD80208 COUPLER,QUICK CONNECT 1 20 VV67104 SPACER 2 21 VF13512 SCREW,FH,M5X15,SST VV60406S HINGE,SST,4" 2 23 VV13607 WASHER,LOCK,Ø GT13056 SCREW,SST,PH,M6X VV66102 PLATE,3.5" CASTER 2 26 VA " CASTER 2 27 VF13495 BOLT,M6X16,HEX 6 28 VF82028 CABLE 1 29 VV67120 CLAMP 1 30 VA13473 SCREW,RHM,M4X16,SST 1 31 VV13635 SCREW,RHM,M5X20,SST 1 32 GT13014 NUT,NYLON,INSERT,M VV60113S WASHER,WHEEL,AL 2 34 VF13551 WASHER,SST,PLAIN,Ø6XØ22X VA75004 WHEEL,10" 2 36 VF13604 WASHER, Ø VV13633 NUT,SST,M VV13634 SCREW,RHM,M5X30,SST 4 39 VV13601 WASHER,LOCK,Ø VF13474A WASHER,SST,PLAIN,Ø5XØ15X VV67505 BUSHING,90,CORD 1 42 VV66200 BOTTOM PLATE,ASSEMBLY 1 43 VV67702 HOSE ASSEMBLY,VACUUM & ASSEMBLY 1 44 VV91559 HAND TOOL 1 13

14 14

15 PARTS LIST DIA NO PART NO DESCRIPTION NUMBER REQ'D 1 VV40328 UPHOLSTERY TOOL 1 2 VV WINDOW,HAND TOOL 1 3 VV20071 SCREW,5/16-18X5/8"L,HH 1 4 VV20298 WASHER,LOCK,5/16 L,SST 1 5 VV60531 GASKET 1 6 VV80159 NOZZLE,SPRAY TIP,80º 1 7 VV80105 BUSHING,BRASS 1 8 VV80115 ELBOW,STREET,45 DEGREES 1 9 VV10933 TRIGGER VALVE 1 10 VV80128 HOSE BARB 1 11 VV10114 CLAMP,HOSE, 3/ VV85317 SOLUTION HOSE,3/ VV80241 HOSE BARB,MAIL END 1 15

16 16

17 PARTS LIST DIA NO PART NO DESCRIPTION NUMBER REQ'D 1 VV60220 CUFF, 1 1/2" 2 2 VV67703 HOSE,VACUUM 1 3 VV20652 TIE,CABLE 16 4 VV80241 HOSE BARB,MAIL PLUG,SST 1 5 VV10114 CLAMP,HOSE,3/8,SST 2 6 VV67704 HOSE,SOLUTION,16'LONG 1 7 VV80128 HOSE BARB 1 8 VV80208 COUPLER,QUICK CONNECT 1 9 VV67703A VACUUM HOSE ASSEMBLY 1 10 VV67704A SOLUTION HOSE ASSEMBLY 1 17

18 18