L65369 Rev Planning Guide. Effective 04/13/15

Transcription

1 L65369 Rev Planning Guide Effective 04/13/15

2 2015 Planning Guide Important Information: This Dacor Planning Guide contains that latest product information as of prill 13th, Specifications are subject to change without notice. For the most accurate and up to date planning guide pages, we recommend that you visit our web site at If you cannot access our web site via computer, please fill out the Planning Guide Update Form on the following page and FX or mail it to us. We can send you updates via or regular mail. If you need additional copies of this planning guide, please contact the Marketing Department at (800) and reference part number: L65369 Revision Thank you Dacor, all rights reserved

3 UPDTE FORM If you cannot access our web site via computer to obtain planning guide updates, fill out this form completely and fax or mail it as instructed below. We will send you updates as they are issued. Please mail this form to the address below or fax it to (626) Dacor tt: Marketing Department PO ox City of Industry, C Full Name: Company name: ddress: City: State: Zip code: Telephone number: Fax number: address: My Dacor representative: Please send updates via: Printed copy Web site:

4 Table of Contents Revised 02/18/15 WLL OVENS Discovery iq Single (DYO, DYOV) Discovery iq Double (DYO, DYOV) Distinctive Single (DTO, DTOV) Distinctive Double (DTO, DTOV) Renaissance Single (RNO, RNOV) Renaissance Double (RNO, RNOV) WRMING DRWERS Renaissance ELECTRIC COOKTOPS Discovery (MET) Distinctive (DECT) Renaissance (ETT) Renaissance Induction (RNCT) GS COOKTOPS Classic Drop-In (SGM) Discovery Slide-In (DYRTP) Distinctive Drop-In (DCT) Distinctive Slide-In (DRT) Renaissance Slide-In (EG) Renaissance Drop-In (RGC) RNGES , 48 Discovery Dual Fuel (DYRP36/48DS) Distinctive Dual Fuel (DR30D) Distinctive Electric (DR30E) Distinctive ll Gas (DR30G) Renaissance Dual Fuel (ER30D) , 48 Renaissance Dual Fuel (ER36/48D) Renaissance ll Gas (ER30G) Renaissance ll Gas (ER36G) Renaissance Electric/Induction (RNR30N) /48 Renaissance ll Gas (RNRPxxG) DUCT 6.1 HOODS Discovery Island Style (DHI) 7.1 Discovery Wall Mount (DHW) 7.2 Discovery Glass Wall Mount (PHW) 7.3 Distinctive Wall Mount (DH) Renaissance Wall Mount (EH, EHR, MH) Integrated Ventilation System (IVS, IVSR) 7.9 Custom Hood Liner (IHL) 7.10 DOWNDRFT VENTS Renaissance Slim Chassis (ERV, PRV) Classic Standard Chassis (RV) LOWERS Cabinet Style for Selected Downdraft Vents (CP) 9.1 Renaissance, In-Line (ILHSF) Renaissance, Remote (REMP) DISHWSHERS Distinctive DDW Renaissance RDW24I/RDW24S REFRIGERTION Distinctive 36 with Dispenser (DTF 4-Door) 11.1 Renaissance 24 Wine Cellar (RNF) 11.2 MICROWVES Discovery Convection Type (DCM24) 12.1 Trim Kits for bove (CTK/DCMTK/OCTK) 12.1 Discovery 24" Microwave-In--Drawer (MMD24) 12.2 Discovery 30" Microwave-In--Drawer (MMD[V]30) 12.3 Discovery Convection Type, Over Range (PCOR30) 12.4 Distinctive Stainless Steel (DMW2420S) 12.5 Trim Kits for bove (MTK/DMWTK/OMTK) 12.5 Renaissance lack Glass (DMT2420K) 12.6 Trim Kits for bove (MTK/OMTK) 12.6 OUTDOOR GRILLS Discovery (O/OS) uilt-in Trim kit for O/OS Series Grills (OGT) " Outdoor Grill Cart, for O/OS36 Grill (OC) 13.5 CKGURDS 14.1 ackguard, Stand-lone (E) 14.1 DISPENSING SYSTEMS Discovery Wine Dispensing System (DYWS) X.1

5 Table of Contents Revised 02/18/15 COMINTION INSTLLTIONS CI.1-CI.21 Drop-In Cooktop/Downdraft Vent/Single Wall Oven CI.1-CI.2 Drop-In Cooktop/Slim Downdraft Vent/Single Wall Oven CI.3-CI.4 Single Wall Oven/Drop-In Cooktop CI.5-CI.6 Cooktop/Range/Downdraft Vent CI.7 Warming Drawer/Drop-In Cooktop CI.8 Warming Drawer/Slide-In Cooktop CI.9 Warming Drawer (stacked)/slide-in Cooktop CI.10 Warming Drawer (side-by-side)/slide-in Cooktop CI.11 DCM Microwave/Warming Drawer CI.12 DMT/DMW Microwave/Warming Drawer CI.13 DCM Microwave/DTO Wall Oven/Warming Drawer CI.14 DMT/DMW Microwave/ DTO Wall Oven/Warming Drawer CI.15 DCM Microwave/DYO Wall Oven/Warming Drawer CI.16 DMT/DMW Microwave/ DYO Wall Oven/Warming Drawer CI.17 DMW Microwave/RNO Wall Oven/ Warming Drawer CI.18 DTO Wall Oven/Microwave In--Drawer/ Warming Drawer CI.19 DYO Wall Oven/Microwave In--Drawer/ Warming Drawer CI.20 RNO Wall Oven/Microwave In--Drawer/ Warming Drawer CI.21 X.2

6 DYO, DYOV Discovery iq 30 Wide Single Wall Ovens Revised 03/10/14 WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. Product tolerances: ±1/16 (±1.6 mm), unless otherwise stated. 3 1/2 (8.9 cm) 1 1/8 (2.9 cm) 1 1/8 (2.9 cm) 3 3/16 (8.1 cm) 1 1/8 (2.9 cm) Dedicated Circuit Required 240 Vac, 4-wire*, 60Hz, 30 mp. Total Connected Load** 240 Vac 60 Hz, 22.5 mp. 5.4 kw * Two 120 Vac hot (L1 and L2), one neutral, one ground. ** This specification is for reference only. See the product data label for exact specifications. HNDLE DIMENSIONS - SIDE VIEW J K Utility cutout Top of chassis F G C H D 21 7/8 (55.6) cm Control panel front Control panel side view E Conduit: 60 (152 cm) long Top of chassis C D E F G H J K 29 7/8 (75.9 cm) 28 1/4 (71.8 cm) 28 11/16 (72.9 cm) 27 3/8 (69.5 cm) 1 5/16 (3.3 cm) 6 1/2 (16.5 cm) 5 (12.7 cm) 7 7/8 (20.0 cm) 1 3/8 (3.5 cm) 23 1/2 (59.7 cm) PRODUCT DIMENSIONS 1.1

7 DYO, DYOV Discovery iq 30 Wide Single Wall Ovens Revised 03/10/14 Cutout tolerances: +1/16 (+1.6 mm), -0, unless otherwise stated. 1 1/2 (3.8 cm) thick typical counter Recommended electrical location 29 3/4 * (75.6 cm) min. to overhang C 4 (10.2 cm) min. between cutout C 1 (2.5 cm) min. to combustible floor 3/4 (1.9 cm) support platform 3/4 (1.9 cm) support platform lternate electrical locations Toe kick CUTOUT DIMENSIONS SIDE-Y-SIDE UNDER-COUNTER INSTLLTION Recommended electrical location 1 1/2 (3.8 cm) thick typical counter 29 3/4 (75.6 cm) * min. to bottom of cabinet door C 3/4 (1.9 cm) support platform 29 3/4 * (75.6 cm) min. to overhang 3/4 (1.9 cm) support platform C 1 (2.5 cm) min. to combustible floor Recommended electrical location Toe kick CUTOUT DIMENSIONS - UNDER-COUNTER INSTLLTION 1 (2.5 cm) min. any obstructions to ventilation lternate electrical location 31 1/4 (79.4 cm) recommended () () (C) 30 (76.2 cm) 28 3/8 to 29 (72.1 cm to 73.7 cm) 27 7/16 to 28 1/4 (69.7 cm to 71.8 cm) 4 typical toe kick NOTES: CUTOUT DIMENSIONS - WLL INSTLLTION * 30 3/4 (76.1 cm) recommended CUTOUT DIMENSIONS 1. Minimum interior cabinet depth: 24 (61.0 cm). 2. 1/8 (3 mm) minimum clearance from appliance to adjacent cabinet doors/drawers. 3. Two (2) Single Ovens are not approved in a stack configuration. 1.2

8 DYO, DYOV Discovery iq 30 Wide Double Wall Ovens Revised 03/10/14 WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. Product tolerances: ±1/16 (±1.6 mm), unless otherwise stated. Dedicated Circuit Required 240 Vac, 4-wire*, 60 Hz, 50 mp. Total Connected Load 240 Vac 60 Hz, 45 mp kw * Two 120 Vac hot (L1 and L2), one neutral, one ground. ** This specification is for reference only. See the product data label for exact specifications. 3 1/2 (8.9 cm) 1 1/8 (2.9 cm) 1 1/8 (2.9 cm) 3 3/16 (8.1 cm) 1 1/8 (2.9 cm) FJ KG HNDLE DIMENSIONS - SIDE VIEW C D 21 7/8 (55.6) cm Control panel front Control panel side view E Top of chassis Conduit: 60 (152 cm) long C D E F G 29 7/8 (75.9 cm) 28 1/4 (71.8 cm) 51 1/8 (129.9 cm) 50 3/16 (127.5 cm) 15/16 (2.4 cm) 1 3/8 (3.5 cm) 23 1/2 (59.7 cm) PRODUCT DIMENSIONS 1.3

9 DYO, DYOV Discovery iq 30 Wide Double Wall Ovens Revised 03/10/14 Cutout tolerances: +1/16 (+1.6 mm), -0, unless otherwise stated. C 5 x 5 vent hole in back of cabinet recommended 52 1/8 (132.4 cm) min. to bottom of cabinet door * lternate electrical location (adjacent cabinet) 3/4 (1.9 cm) support platform 1 (2.5 cm) min. to top of drawer face Recommended electrical location 9 5/8 (24.4 cm) recommended 4 typical toe kick * 53 1/8 (134.9 cm) recommended () () (C) 30 (76.2 cm) 28 3/8 to 29 (72.1 cm to 73.7 cm) 50 1/4 to 50 3/4 (127.6 cm to cm) CUTOUT DIMENSIONS NOTES: 1. Minimum interior cabinet depth: 24 (61.0 cm). 2. 1/8 (3 mm) minimum clearance from appliance to adjacent cabinet doors/drawers. 1.4

10 DTO, DTOV Distinctive 27 and 30 Wide Single Wall Ovens Revised 10/10/14 Product tolerances: ±1/16 (±1.6 mm) unless otherwise stated J K Utility cutout Top of chassis F WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. G C H D Control panel front Control panel side view 3 1/2 (8.9 cm) 1 1/8 (2.9 cm) E 1 1/8 (2.9 cm) 3 3/16 (8.1 cm) Conduit: 60 (152 cm) long Top of chassis 1 1/8 (2.9 cm) Model DTO[V]127 DTO[V]130 (F) Utility Cutout Width 6 1/2 (16.5 cm) () Overall Width 26 7/8 (68.3 cm) 29 7/8 (75.9 cm) (G) Utility Cutout Height 5 (12.7 cm) () Chassis Width 25 1/2 (64.8 cm) 28 1/2 (72.4 cm) (C) Overall Height 27 3/4 (70.5 cm) 27 3/4 (70.5 cm) (H) Utility Cutout Depth 7 7/8 (20.0 cm) 21 7/8 (55.6) cm (D)* Chassis Height 26 5/8 (67.6 cm) 26 5/8 (67.6 cm) (J) Control Panel Depth 1 1/4 (3.2 cm) (E) Control Panel Overlay 1 1/8 (2.9 cm) 1 1/8 (2.9 cm) (K) Chassis Depth 23 1/2 (59.7 cm) Epicure Millennia (Order kit #ROVH30S) Handle Dimensions Flush Model DTO[V]127 DTO[V]130 ELECTRICL SPECIFICTIONS Dedicated Circuit Requirements 240 Vac 60 Hz., 4-wire,*** 30 mp. 240 Vac 60 Hz., 4-wire,*** 30 mp. Total Connected Load 240 Vac 60 Hz, 23.3 mp., 5.6 kw 240 Vac 60 Hz, 24.9 mp., 6.0 kw *** Two 120 Vac hot (L1 and L2), one neutral, one ground The above specifications are for reference only. See the appliance data plate for exact specifications. 1.5

11 DTO, DTOV Distinctive 27 and 30 Wide Single Wall Ovens Revised 10/10/14 Cabinet/countertop tolerances: +1/16, -0, (+1.6 mm, -0) unless otherwise stated 1 (2.5 cm) min. to combustibles 1 1/2 (3.8 cm) typical counter 36 typ. (91.4 cm) P R Recommended electrical location 4 typical toe kick N 3/4 (1.9 cm) support platform 1 (2.5 cm) min. to combustible floor SINGLE WLL OVEN - INSTLLED UNDER COUNTER 1 (2.5 cm) min. to bottom of cabinet door Recommended electrical location Model Minimum Interior Cabinet Depth: 24 (61.0 cm) (N) Minimum Cabinet Width (P) Cut Out Width (R) Cutout Height P R 3/4 (1.9 cm) support platform DTO[V]127 DTO[V] (68.6 cm) 30 (76.2 cm) 25 5/8 (65.1 cm) minimum (recommended) 26 1/8 (66.4 cm) maximum 28 5/8 (72.7 cm) minimum (recommended) 29 1/8 (74.0 cm) maximum 26 3/4 (67.9 cm) minimum (recommended) 27 1/2 (69.9 cm) maximum 26 3/4 (67.9 cm) minimum (recommended) 27 1/2 (69.9 cm) maximum 1 (2.5 cm) min. to top of cabinet door lternate electrical location 31 1/4 (79.4 cm) recommended 4 typical toe kick SINGLE WLL OVEN - CUTOUT DIMENSIONS 1.6

12 DTO, DTOV Distinctive 27 and 30 Wide Double Wall Ovens Revised 10/10/14 Product tolerances: ±1/16 (±1.6 mm) unless otherwise stated J K Utility cutout Top of chassis F G WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. H C D 21 7/8 (55.6) cm Control panel front Control panel side view E Top of chassis Conduit: 60 (152 cm) long Model DTO[V]227 DTO[V]230 () Overall Width 26 7/8 (68.3 cm) 29 7/8 (75.9 cm) () Chassis Width 25 1/2 (64.8 cm) 28 1/2 (72.4 cm) (C) Overall Height 50 1/8 (127.3 cm) 50 1/8 (127.3 cm) (D) Chassis Height 49 (124.5 cm) 49 (124.5 cm) (E) Control Panel Overlay 1 1/8 (2.9 cm) 1 1/8 (2.9 cm) 3 1/2 (8.9 cm) 1 1/8 (2.9 cm) 1 1/8 (2.9 cm) 3 3/16 (8.1 cm) 1 1/8 (2.9 cm) (F) Utility Cutout Width 6 1/2 (16.5 cm) (G) Utility Cutout Height 5 (12.7 cm) (H) Utility Cutout Depth 7 7/8 (20.0 cm) (J) Control Panel Depth 1 1/4 (3.2 cm) (K) Chassis Depth 23 1/2 (59.7 cm) Model DTO[V]227 DTO[V]230 ELECTRICL SPECIFICTIONS Dedicated Circuit Total Connected Load Requirements 240 Vac 60 Hz., 4-wire,* 40 mp. 240 Vac 60 Hz., 4-wire,* 40 mp. 240 Vac 60 Hz, 26.2 mp., 6.4 kw 240 Vac 60 Hz, 26.6 mp., 6.4 kw * Two 120 Vac hot (L1 and L2), one neutral, one ground Epicure Millennia (Order kit #ROVH30S) Flush The above specifications are for reference only. See the appliance data plate for exact specifications. Handle Dimensions 1.7

13 DTO, DTOV Distinctive 27 and 30 Wide Double Wall Ovens Revised 10/10/14 Cabinet/countertop tolerances: +1/16, -0, (+1.6 mm, -0) unless otherwise stated N 1 (2.5 cm) min. to bottom of cabinet door Recommended electrical location R P 3/4 (1.9 cm) support platform 1 (2.5 cm) min. to top of drawer face 4 typical toe kick 9 5/8 (24.4 cm) recommended Minimum Interior Cabinet Depth: 24 (61.0 cm) Model (N) Minimum Cabinet Width (P) Cut Out Width (R) Cutout Height DTO[V] (68.6 cm) 25 5/8 (65.1 cm) minimum (recommended) 26 1/8 (66.4 cm) maximum 49 1/8 (124.8 cm) minimum (recommended) 50 (127.0 cm) maximum DTO[V] (76.2 cm) 28 5/8 (72.7 cm) minimum (recommended) 29 1/8 (74.0 cm) maximum 49 1/8 (124.8 cm) minimum (recommended) 50 (127.0 cm) maximum 1.8

14 RNO, RNOV Renaissance 27 and 30 Wide Single Wall Ovens Revised 11/25/14 J Product tolerances: ±1/16 (±1.6 mm) unless otherwise stated K Utility cutout Top of chassis F G WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. 2 3/8 (6.0 cm) 1 7/8 (4.8 cm) C H D Control panel front Control panel side view L E M Conduit: 60 (152 cm) long Top of chassis Epicure Model RNO[V]127 RNO[V]130 Millennia (Order kit #ROVH30S) Handle Dimensions Flush ELECTRICL SPECIFICTIONS Dedicated Circuit Total Connected Load Requirements 240 Vac 60 Hz., 4-wire,*** 30 mp. 240 Vac 60 Hz., 4-wire,*** 30 mp. 240 Vac 60 Hz, 19.0 mp., 4.7 kw 240 Vac 60 Hz, 24.5 mp., 6.0 kw *** Two 120 Vac hot (L1 and L2), one neutral, one ground The above specifications are for reference only. See the appliance data plate for exact specifications. 21 1/2 (54.6) cm Model RNO[V]127 RNO[V]130 () Overall Width 26 7/8 (68.3 cm) 29 7/8 (75.9 cm) () Chassis Width 25 1/2 (64.8 cm) 28 1/2 (72.4 cm) * To top of chassis notch behind control panel (C) Overall Height 27 3/4 (70.5 cm) 27 3/4 (70.5 cm) (D)* Chassis Height 27 3/8 (69.5 cm) 27 3/8 (69.5 cm) (E) Control Panel Overlay 3/8 (1.0 cm) 3/8 (1.0 cm) (F) Utility Cutout Width 6 1/2 (16.5 cm) (G) Utility Cutout Height 5 (12.7 cm) (H) Utility Cutout Depth 7 7/8 (20.0 cm) (J) Control Panel Depth 3/4 * (1.9 cm) (K) Chassis Depth 24 (61.0 cm) * 7/8 (2.2 cm) for models RNO[V]127, RNO[V]130, RNO127W and RNO130W (L) Control Panel Notch Depth 1/2 (1.3 cm) (M) Notch Height 3/4 (1.9 cm) 1.9

15 RNO, RNOV Renaissance 27 and 30 Wide, Single Wall Oven Revised 11/25/14 Cabinet tolerances: +1/16 (+1.6 mm) -0, unless otherwise stated 1 (2.5 cm) min. to combustibles 1 1/2 (3.8 cm) typical counter N 36 typ. (91.4 cm) P R Recommended electrical location 4 typical toe kick 1 (2.5 cm) min. to bottom of cabinet door Recommended electrical location 3/4 (1.9 cm) support platform 1 (2.5 cm) min. to combustible floor CUTOUT DIMENSIONS - STNDRD UNDER COUNTER INSTLLTION SINGLE WLL OVEN Minimum interior cabinet depth: 24 (61.0 cm) Model (N) Minimum Cabinet Width (P) Cutout Width (R) Minimum Cutout Height P R 3/4 (1.9 cm) support platform RNO[V]127 RNO[V] (68.6 cm) 30 (76.2 cm) 25 5/8 (65.1 cm) minimum (recommended) 26 1/8 (66.4 cm) maximum 28 5/8 (72.7 cm) minimum (recommended) 29 1/8 (74.0 cm) maximum 27 1/2 (69.9 cm) 27 1/2 (69.9 cm) 1 (2.5 cm) min. to top of cabinet door lternate electrical location 31 1/4 (79.4 cm) recommended 4 typical toe kick CUTOUT DIMENSIONS - STNDRD WLL INSTLLTION SINGLE WLL OVEN 1.10

16 RNO, RNOV Renaissance 27 and 30 Wide, Single Wall Oven Revised 11/25/14 CUTOUT DIMENSIONS - FLUSH INSTLLTION SINGLE WLL OVEN Cabinet tolerances: +1/16 (+1.6 mm) -0, unless otherwise stated T Finished stops * W TOP VIEW U V X VENTILTION INSET 3/4 (1.9 cm) SIDE VIEW Cabinet face 1 (2.5 cm) ** ** 1 1/8 (2.9 cm) for models RNO[V]127, RNO[V]130, RNO127W, RNO130W FRONT VIEW Model (T) Minimum Cabinet Depth (U) Cutout Width (V) Cutout Height (W) Stop Depth (X) Stop Width RNO127[F]S 24 3/4 (62.9 cm) 27 (68.6 cm) 27 7/8 (70.8 cm) 3/4 (1.9 cm) 3/8 (1.0 cm) RNO130[F]S 24 3/4 (62.9 cm) 30 (76.2 cm) 27 7/8 (70.8 cm) 3/4 (1.9 cm) 3/8 (1.0 cm) RNO[V]127, RNO127W 24 7/8 (63.2 cm) 27 (68.6 cm) 27 7/8 (70.8 cm) 7/8 (2.2 cm) 3/8 (1.0 cm) RNO[V]130, RNO130W 24 7/8 (63.2 cm) 30 (76.2 cm) 27 7/8 (70.8 cm) 7/8 (2.2 cm) 3/8 (1.0 cm) * ack of wall oven control panel rests against stops 1.11

17 RNO, RNOV Renaissance 27 and 30 Wide Double Wall Ovens Revised 01/13/15 Product tolerances: ±1/16 (±1.6 mm) unless otherwise stated J K Utility cutout Top of chassis F G WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. H C D 21 1/2 (54.6) cm Control panel front Control panel side view L E M Top of chassis Conduit: 60 (152 cm) long Model RNO[V]227 RNO[V]230 ELECTRICL SPECIFICTIONS Dedicated Circuit Total Connected Load Requirements 240 Vac 60 Hz., 4-wire,*** 40 mp. 240 Vac 60 Hz., 4-wire,*** 50 mp. 240 Vac 60 Hz, 39.4 mp., 9.5 kw 240 Vac 60 Hz, 48.6 mp., 12.0 kw *** Two 120 Vac hot (L1 and L2), one neutral, one ground The above specifications are for reference only. See the appliance data plate for exact specifications. Model RNO[V]227 RNO[V]230 () Overall Width 26 7/8 (68.3 cm) 29 7/8 (75.9 cm) () Chassis Width 25 1/2 (64.8 cm) 28 1/2 (72.4 cm) * To top of chassis notch behind control panel (C) Overall Height 50 1/8 (127.3 cm) 50 1/8 (127.3 cm) (D)* Chassis Height 49 3/4 (126.4 cm) 49 3/4 (126.4 cm) (E) Control Panel Overlay 3/8 (1.0 cm) 3/8 (1.0 cm) (F) Utility Cutout Width (G) Utility Cutout Height (H) Utility Cutout Depth (J) Control Panel Depth (K) Chassis Depth (L) Control Panel Notch Depth (M) Notch Height 6 1/2 (16.5 cm) 5 (12.7 cm) 7 7/8 (20.0 cm) 3/4 (1.9 cm) 24 (61.0 cm) 1/2 (1.3 cm) 3/4 (1.9 cm) 1.12

18 RNO, RNOV Renaissance 27 and 30 Wide Double Wall Ovens Revised 01/13/15 N 2 3/8 (6.0 cm) 1 7/8 (4.8 cm) 1 (2.5 cm) min. to bottom of cabinet door Recommended electrical location Epicure Millennia (Order kit #ROVH30S) Flush R Handle Dimensions P 3/4 (1.9 cm) support platform 1 (2.5 cm) min. to top of drawer face 4 typical toe kick 9 5/8 (24.4 cm) recommended DOULE WLL OVEN - CUTOUT DIMENSIONS Model (N) Minimum Cabinet Width (P) Cut Out Width (R) Minimum Cutout Height RNO[V] (68.6 cm) 25 5/8 (65.1 cm) minimum (recommended) 26 1/8 (66.4 cm) maximum 49 7/8 (126.7 cm) RNO[V] (76.2 cm) 28 5/8 (72.7 cm) minimum (recommended) 29 1/8 (74.0 cm) maximum 49 7/8 (126.7 cm) Minimum interior cabinet depth: 24 (61.0 cm) 1.13

19 RNO, RNOV Renaissance 27 and 30 Wide, Double Wall Oven Revised 01/13/15 CUTOUT DIMENSIONS - FLUSH INSTLLTION DOULE WLL OVEN Cabinet tolerances: +1/16 (+1.6 mm) -0, unless otherwise stated T Finished stops * W TOP VIEW U X V VENTILTION INSET 3/4 (1.9 cm) SIDE VIEW Cabinet face 1 (2.5 cm) ** ** 1 1/8 (2.9 cm) for models RNO[V]227, RNO[V]230, RNO227W, RNO230W FRONT VIEW Model (T) Minimum Cabinet Depth (U) Cutout Width (V) Cutout Height (W) Stop Depth (X) Stop Width RNO227[F]S 24 3/4 (62.9 cm) 27 (68.6 cm) 50 1/4 (127.6 cm) 3/4 (1.9 cm) 3/8 (1.0 cm) RNO230[F]S 24 3/4 (62.9 cm) 30 (76.2 cm) 50 1/4 (127.6 cm) 3/4 (1.9 cm) 3/8 (1.0 cm) RNO[V]227, RNO227W 24 7/8 (63.2 cm) 27 (68.6 cm) 50 1/4 (127.6 cm) 7/8 (2.2 cm) 3/8 (1.0 cm) RNO[V]230, RNO230W 24 7/8 (63.2 cm) 30 (76.2 cm) 50 1/4 (127.6 cm) 7/8 (2.2 cm) 3/8 (1.0 cm) * ack of wall oven control panel rests against stops 1.14

20 DWD, ERWD, EWD, IWD, MRWD, MWDH, MWDV, OWD, RWDV 24, 27, 30, 36 Wide Warming Drawers Revised 01/18/12 Product tolerances: ±1/16 (±1.6 mm) unless otherwise stated DWD 1 (2.5 cm) 3 1/2 (8.9 cm) 1 1/8 (2.9 cm) ERWD 3 7/16 (8.7 cm) EWD 1 (2.5 cm) Electrical Circuit Required 120 Vac, 60 Hz, 15 mp. grounded, dedicated circuit 10 1/8 (25.7 cm) Total Connected Load Vac, 60 Hz. Minimum mbient Operating Temperature 32 F (0 C) 1 7/16 (3.7 cm) MRWD30 (only) ll other MRWD series 1 (2.5 cm) MWDH, MWDV, RWDV 3 1/4 (8.3 cm) 1 (2.5 cm) DRWER FCE DIMENSIONS (MWD SERIES SHOWN) HNDLE DIMENSIONS - SIDE VIEW Mounting hole 9 places 40 (101.6 cm) 3-prong 120 Vac power cord 1/2" (1.3 cm) 9" (22.9 cm) C 10" (25.4 cm) Chassis without drawer inserted Chassis 23 3/8 (59.4 cm) 1/2" (1.3 cm) CHSSIS DIMENSIONS Drawer open 5/64" (2 mm) OVERLL DIMENSIONS - TOP VIEW (EWD SERIES SHOWN) 23 13/16 (60.5 cm) Model () Drawer Face Width () Chassis Face Width (C) Chassis Width DWD30 30 (76.2 cm) 29 5/8 (75.2 cm) 28 1/4 (71.8 cm) ERWD27 27 (68.6 cm) 26 5/8 (67.6 cm) 25 1/4 (64.1 cm) ERWD30 30 (76.2 cm) 29 5/8 (75.2 cm) 28 1/4 (71.8 cm) EWD24 24 (61.0 cm) 23 5/8 (60.0 cm) 22 1/4 (56.5 cm) EWD27 27 (68.6 cm) 26 5/8 (67.6 cm) 25 1/4 (64.1 cm) EWD30 30 (76.2 cm) 29 5/8 (75.2 cm) 28 1/4 (71.8 cm) EWD36 36 (91.4 cm) 35 5/8 (90.5 cm) 34 1/4 (87.0 cm) MRWD /4 (67.9 cm) 26 5/8 (67.6 cm) 25 1/4 (64.1 cm) MRWD /4 (75.6 cm) 29 5/8 (75.2 cm) 28 1/4 (71.8 cm) MWDH27 27 (68.6 cm) 26 5/8 (67.6 cm) 25 1/4 (64.1 cm) MWDH30 30 (76.2 cm) 29 5/8 (75.2 cm) 28 1/4 (71.8 cm) MWDV27 27 (68.6 cm) 26 5/8 (67.6 cm) 25 1/4 (64.1 cm) MWDV30 30 (76.2 cm) 29 5/8 (75.2 cm) 28 1/4 (71.8 cm) RWDV30 30 (76.2 cm) 29 5/8 (75.2 cm) 28 1/4 (71.8 cm) WRMING DRWER OVERLL DIMENSIONS 2.1

21 DWD, ERWD, EWD, IWD, MRWD, MWDH, MWDV, OWD, RWDV 24, 27, 30, 36 Wide Warming Drawers Revised 01/18/12 Product tolerances: ±1/16 (±1.6 mm) unless otherwise stated C Electrical Circuit Required 120 Vac, 60 Hz, 15 mp. grounded, dedicated circuit Total Connected Load Vac, 60 Hz. Minimum mbient Operating Temperature 32 F (0 C) Chassis E 5/16 (8 mm) D Drawer open F DRWER FCE DIMENSIONS (IWD/OWD SERIES SHOWN) OVERLL DIMENSIONS - IWD/OWD SERIES TOP VIEW ** ** Mounting hole, 9 places 40" (101.6 cm) 3 prong 120 Vac power cord ** ** G Chassis without drawer installed ** = OWD24 mounting holes CHSSIS DIMENSIONS (IWD/OWD SHOWN) Model () Dimension Drawer Face Width () Dimension Chassis Width (C) Dimension Chassis Face Width (D) Dimension Drawer Face Height (E) Dimension Chassis Depth (F) Dimension Drawer Depth (G) Dimension Chassis Height IWD /16 (56.7 cm) 22 1/4 (56.5 cm) 22 3/8 (56.8 cm) IWD /16 (64.3 cm) 25 1/4 (64.1 cm) 25 3/8 (64.5 cm) IWD /16 (71.9 cm) 28 1/4 (71.8 cm) 28 3/8 (72.1 cm) 8 15/16 (22.7 cm) 23 3/8 (59.4 cm) 23 13/16 (60.5 cm) 9 1/16 (23.0 cm) OWD /2 (57.1 cm) 22 1/2 (57.1 cm) 22 1/2 (57.1 cm) 11 7/8 (30.2 cm) 20 (50.8 cm) 18 (45.7 cm) 11 7/8 (30.2 cm) 2.2

22 DWD, ERWD, EWD, IWD, MRWD, MWDH, MWDV, OWD, RWDV 24, 27, 30, 36 Wide Warming Drawers Revised 01/18/12 Cabinet/countertop tolerances: +1/16 (+1.6 mm), -0 unless otherwise stated 36" typ. Warming drawer (91.4 cm) Warming 120 Vac drawer electrical outlet 27"/30"/36" Dacor single wall oven Warming drawer Warming drawer 120 Vac elect. 120 Vac elect. D C D C 36" typ. (91.4 cm) C C 3/4" min.* (1.9 cm) D 3/4" min.* (1.9 cm) Cooktop WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. Mounting platform must be 3/4" (1.9 cm) thick and support 100 lbs. 1 1/2" (3.8 cm) Typical countertop Warming drawer C 120 Vac electrical outlet 3/4 min.* (1.9 cm) Toe kick 3/4" min.* (1.9 cm) Model () Cutout Width () Min. Width to djacent Doors/ Drawers (C) Cutout Height (D) Min. Vertical Gap etween Cutouts Min. Cutout Depth DWD /2 (72.4 cm) 30 1/4 (76.8 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* ERWD /2 (64.8 cm) 27 1/4 (69.2 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* ERWD /2 (72.4 cm) 30 1/4 (76.8 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* EWD /2 (57.2 cm) 24 1/4 (61.6 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* EWD /2 (64.8 cm) 27 1/4 (69.2 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* EWD /2 (72.4 cm) 30 1/4 (76.8 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* EWD36**** 34 1/2 (87.6 cm) 36 1/4 (92.1 cm)* 9 1/8 (23.2 cm) N IWD /2 (57.2 cm) ** 9 1/8 (23.2 cm) 1 1/16 (2.7 cm) IWD /2 (64.8 cm) ** 9 1/8 (23.2 cm) 1 1/16 (2.7 cm) 24 (61.0 cm) IWD /2 (72.4 cm) ** 9 1/8 (23.2 cm) 1 1/16 (2.7 cm) MRWD /2 (64.8 cm) 27 (68.6 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* MRWD /2 (72.4 cm) 30 (76.2 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* MWDH /2 (64.8 cm) 27 1/4 (69.2 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* MWDH /2 (72.4 cm) 30 1/4 (76.8 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* MWDV /2 (64.8 cm) 27 1/4 (69.2 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* MWDV /2 (72.4 cm) 30 1/4 (76.8 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* OWD24***** 22 5/8 (57.5 cm) 24 1/4 (61.6 cm)*** 11 15/16 (30.3 cm) N 20 1/8 (51.1 cm) RWDV /2 (72.4 cm) 30 1/4 (76.8 cm)* 9 1/8 (23.2 cm) 1 1/4 (3.2 cm)* 24 (61.0 cm) * are minimum spacing to allow for ventilation and avoid scraping on DWD, ERWD, EWD, MRWD, MWDH, MWDV and RWDV series models. ** On IWD series models or OWD24 without the optional front panel kit: The chassis and the drawer faceplate are smaller than the cutout. The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must exceed the appropriate cutout dimensions ( and C above) to cover the hole. llow 1/4" minimum additional space on the top, bottom and sides from the custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop. *** OWD24 with optional factory front panel kit only. are minimum spacing shown to avoid scraping. Gap above and below cutout is 3/4 minimum. See ** above for OWD24 with custom front panel. **** Model EWD36 cannot be installed above or below another warming drawer (any type). ***** Model OWD24 cannot be installed above, below or adjacent to a wall oven or warming drawer (any type). 2.3

23 MET304, MET365-1 Discovery 30 and 36 Wide, Electric Cooktops Revised 10/20/14 Product tolerances: ±1/16 (±1.6 mm) unless otherwise noted 30 1/4" * (76.8 cm) 4 (10.2 cm) chassis height 3/16 (4.8 mm) WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. 21 1/4" * (54.0 cm) 19 3/8" (49.5 cm) 28 3/8" (72.1 cm) 36 1/4" * (92.1 cm) 4 (10.2 cm) chassis height 3/16 (4.8 mm) PRODUCT DIMENSIONS - MET /4" * (54.0 cm) 19 3/8" (49.5 cm) 34 3/8" (87.3 cm) PRODUCT DIMENSIONS - MET365-1 * For units with stainless steel trim, other units may be up to 1/8" less. Model No. Electrical Circuit Required Total Connected Load* MET Vac, 60 Hz, 40 mps. 6.9 kw (29 mps.) MET Vac, 60 Hz, 50 mps.* 9.6 kw (40 mps.) * For reference only, See the product data label on bottom of unit for exact specifications. ELECTRICL SUPPLY REQUIREMENTS Minimum Supply Wire Size Line and Ground Connections No. 8 WG NOTES: 1. The cooktop is supplied with a flexible, 48 inch long power conduit consisting of two (2) insulated hot lead conductors (L1 and L2) and one (1) insulated ground conductor. There is no neutral connection. ll leads are copper. The conduit is connected to the right corner of the cooktop. Do not connect the ground wire to neutral. 2. Tested in accordance with the latest edition of NSI Z21.1 and U.L. 858 Standard for household cooking appliances. 3. These cooktops are not approved for recessed installation. 3.1

24 MET304, MET365-1 Discovery 30 and 36 Wide, Electric Cooktops Revised 10/20/14 ll tolerances: +1/16, -0, (+1.6 mm, -0) unless otherwise stated llow a minimum of 6 inches (15.2 cm) clearance between the top of the countertop and any combustible surface below, including the upper edge of a drawer below the cooktop. Proper under-cabinet clearance is also required for the cooktop hold down brackets. When installing model MET365-1 and the bottom of the chassis is to be enclosed wall to wall, you must install Dacor ventilation duct kit TD323. Cooktop cutout in top of cabinet 6 (15.2 cm) min. clearance to combustible surfaces 7 3 / 4 X 4 3 / 8 ventilation cut-outs in enclosure floor Model () Minimum Under Counter Clearance (Width) MET304 MET /2 (77.5 cm) 36 1/2 (92.7 cm) 3 /4 1 1 / / 2 3 /4 UNDER COUNTER CLERNCE TOP VIEW VENTILTION CUTOUT Cabinets that are: () Overhead Clearances: ll Installations Directly above cooking surface 1 To left or right of cooking surface 1, 2 30 (76.2 cm) 18 (45.7 cm) Rear wall 6" (15.2 cm) min. from mounting surface to combustibles below cooktop chassis C Model MET304 MET365-1 (C) Cutout Width: Installations without Downdraft Vent 28 3/4 (73.0 cm) 34 3/4 (88.3 cm) 2 1/4 min. (5.7 cm) 19 3/4 (50.2 cm) 1 min. (2.5 cm) 6 (15.2 cm) min. to combustible, side wall, both sides COUNTERTOP CUTOUT (WITHOUT DOWNDRFT VENT) 3.2

25 MET304, MET365-1 Discovery 30 and 36 Wide, Electric Cooktops Revised 10/20/14 ll tolerances: +1/16 (+1.6 mm), -0, unless otherwise stated. 3/8 min. (1.0 cm) flat countertop overhang required behind cutout Countertop 5/8 min. (1.6 cm) flat countertop overhang required behind cutout Countertop Stiffener ETT or MET series cooktop Stiffener ETT or MET series cooktop Cabinet face 3/8 min. (1.0 cm) space behind downdraft vent chassis to clear stiffener ERV or PRV series downdraft vent: Check downdraft vent specifications to determine proper fit Cabinet face 5/8 min. (1.6 cm) space behind downdraft vent chassis to clear stiffener RV series downdraft vent: Check downdraft vent dimensions/specifications to determine proper fit 4 5/8 (11.7 cm) 9 7/8 (25.1 cm) with CP3 blower installed Floor Floor ERV ND PRV SERIES DOWNDRFT VENT INSTLLTION SIDE VIEW RV SERIES DOWNDRFT VENT INSTLLTION SIDE VIEW E C F Rear wall D 19 3/4" (50.2 cm) Cabinet face 1" min. (2.5 cm) 6" (15.2 cm) min. from mounting surface to combustibles below cooktop chassis 6" min. (15.2 cm) 6" min. (15.2 cm) COUNTERTOP CUTOUT (WITH DOWNDRFT VENT) TOP VIEW Cabinets that are: Directly above cooking surface 1 To left or right of cooking surface 1, 2 COUNTERTOP CUTOUT (WITH DOWNDRFT VENT) ISO VIEW () Overhead Clearances: ll Installations 30 (76.2 cm) 18 (45.7 cm) Model/Configuration () Cooktop Cutout Width (C) Downdraft Vent Cutout Width (D) Total Cutout Depth (E) Downdraft Vent Cutout Depth (F) Minimum Rear Countertop Overhang MET304 cooktop with ERV30[15] or PRV30 downdraft vent 28 3/4 27 3/4 22 1/2 (57.2 cm) 2 3/4 (7.0 cm) 3/8 (1.0 cm) MET304 cooktop with RV30 downdraft vent (73.0 cm) (70.5 cm) 22 1/4 (56.5 cm) 2 1/2 (6.4 cm) 5/8 (1.6 cm) MET365-1 cooktop with ERV36[15] or PRV36 downdraft vent 34 3/4 33 3/4 22 1/2 (57.2 cm) 2 3/4 (7.0 cm) 3/8 (1.0 cm) MET365-1 cooktop with RV36 downdraft vent (88.3 cm) (85.7 cm) 22 1/4 (56.5 cm) 2 1/2 (6.4 cm) 5/8 (1.6 cm) 3.3

26 DECT304, DECT365 Distinctive 30 and 36 Wide, Electric Cooktops Revised 10/17/13 Product tolerances: ±1/16 (±1.6 mm) unless otherwise noted WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. 30 (76.2 cm) 21 (53.3 cm) 19 3/16 (48.8 cm) 28 5/8 (72.7 cm) 2 (5.18 cm) PRODUCT DIMENSIONS - DECT (91.4 cm) 21 (53.3 cm) 19-3/16 (48.8 cm) 2 (5.18 cm) 34 (86.3 cm) PRODUCT DIMENSIONS - DECT365 IMPORTNT: DECT series cooktops are not approved for installation with a downdraft vent. Model No. Electrical Circuit Required Total Connected Load* Minimum Supply Wire Size Line and Ground Connections DECT Vac, 60 Hz, 30 mps. 6.7 kw (28 mps.) No. 10 WG DECT Vac, 60 Hz, 40 mps. 9.4 kw (39 mps.) No. 8 WG * For reference only, See the product data label on bottom of unit for exact specifications. ELECTRICL SUPPLY REQUIREMENTS NOTES: 1. The cooktop is supplied with a flexible, 48 inch long power conduit consisting of two (2) insulated hot lead conductors (L1 and L2) and one (1) insulated ground conductor. There is no neutral connection. ll leads are copper. The conduit is connected to the right rear corner of the cooktop. Do not cut or lengthen the conduit. 2. These cooktops are not approved for recessed installation. 3.4

27 DECT304, DECT365 Distinctive 30 and 36 Wide, Electric Cooktops Revised 10/17/13 ll tolerances: +1/16 (+1.6 mm), -0 unless otherwise stated 1 1/2" (3.8 cm) min. clearance - Width of cut - Depth of cut 1 (2.5 cm) from edge of cutout to front of countertop Hole in cabinet floor for conduit routing: 3 1/2" (9 cm) deep x 2 1/2" (6.5 cm) wide See notes 1-1/4" (3.2 cm) Canadian 2-1/4" (5.7 cm) US COUNTERTOP CUTOUT IMPORTNT: Under the cooktop it is necessary to install a partition, spaced from the bottom of the appliance as shown. Wall covering cabinets, and countertop must withstand heat up to 200 F (93 C) H Install junction box so that it can be reached through the front of the cabinet CINET DIMENSIONS ND REQUIREMENTS CONDUIT OPENING Model () () (C) (D) (E) (F) (G) (H) DECT304 DECT /16 (72.9 cm) to 28 15/16 (73.5 cm) 34-1/16 (86,5 cm) to 34-5/16 (87.2 cm) 19-1/4 (49.0 cm) to 19-9/16 (49.7 cm) 19-1/4 (49.0 cm) to 19-9/16 (49.7 cm) 30 (76.2 cm) min. 36 (91.4 cm) min. 18 (45.7 cm) min height from countertop to nearest cabinet on either side of unit 30 (76.2 cm) min.* clearance from countertop to unprotected overhead surface 2 (5 cm) min. clearance from cutout to side wall on the left and right of the unit 13 (33 cm) depth of unprotected overhead 12 (31 cm) min. from bottom of countertop and adjacent cabinet (right side) * 24 (61 cm) min. clearance if bottom of wood or metal cabinets is protected by not less than 1/4 (0.6 cm) flame retardant millboard covered with no less than No. 28 MSG sheet steel (0.04 cm) stainless steel, or (0.06 cm) aluminum or (0.05cm) copper. 30 (76.2 cm) min. clearance between top of cooking platform and bottom of unprotected wood or metal cabinet. NOTES: 1. Chamfer all exposed edges of decorative laminate to prevent damage from chipping. 2. Radius corners of cutout and file to insure smooth edges and prevent corner cracking. Recommend 1/4 or 3/8 diameter drill In each corner. 3. Rough edges, inside corners which have not been rounded and forced fits can contribute to cracking of the countertop laminate. 4. This cooktop has been designed with wide tolerances of cut-out to cover possible replacement with other brands. Dacor recommends that you use the minimum cutout dimensions in the case of new Installation. 5. lways consult the countertop manufacturer for specific instructions. 6. Ensure the countertop is square and level and ensure no structural members interfere with space requirements. 7. The junction box, must be located where it will allow considerable slack in the conduit for serviceability. 8. For solid surface material installations such as Surel and Corian, consult with solid surface manufacturer to determine if heat reflective tape is required. 3.5

28 ETT304-1, ETT365-2 Renaissance 30 and 36 Wide, Electric Cooktops Revised 10/20/14 Product tolerances: ±1/16 (±1.6 mm) unless otherwise noted 30 1/4" * (76.8 cm) 4 (10.2 cm) chassis height 3/16 (4.8 mm) WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. 21 1/4" * (54.0 cm) 19 3/8" (49.5 cm) 28 3/8" (72.1 cm) 36 1/4" * (92.1 cm) 4 (10.2 cm) chassis height 3/16 (4.8 mm) PRODUCT DIMENSIONS - ETT /4" * (54.0 cm) 19 3/8" (49.5 cm) 34 3/8" (87.3 cm) PRODUCT DIMENSIONS - ETT365-2 * For units with stainless steel trim, other units may be up to 1/8" less. Model No. Electrical Circuit Required Total Connected Load* ETT Vac, 60 Hz, 40 mps. 6.9 kw (29 mps.) ETT Vac, 60 Hz, 40 mps. 9.1 kw (38 mps.) * For reference only, See the product data label on bottom of unit for exact specifications. ELECTRICL SUPPLY REQUIREMENTS Minimum Supply Wire Size Line and Ground Connections No. 8 WG NOTES: 1. The cooktop is supplied with a flexible, 48 inch long power conduit consisting of two (2) insulated hot lead conductors (L1 and L2) and one (1) insulated ground conductor. There is no neutral connection. ll leads are copper. The conduit is connected to the right corner of the cooktop. Do not connect the ground wire to neutral. 2. Tested in accordance with the latest edition of NSI Z21.1 and U.L. 858 Standard for household cooking appliances. 3. These cooktops are not approved for recessed installation. 3.6

29 ETT304-1, ETT365-2 Renaissance 30 and 36 Wide, Electric Cooktops Revised 10/20/14 ll tolerances: +1/16, -0, (+1.6 mm, -0) unless otherwise stated llow a minimum of 6 inches (15.2 cm) clearance between the top of the countertop and any combustible surface below, including the upper edge of a drawer below the cooktop. Proper under-cabinet clearance is also required for the cooktop hold down brackets. When installing model ETT365-2 and the bottom of the chassis is to be enclosed wall to wall, you must install Dacor ventilation duct kit TD323. Cooktop cutout in top of cabinet 6 (15.2 cm) min. clearance to combustible surfaces 7 3 / 4 X 4 3 / 8 ventilation cut-outs in enclosure floor Model () Minimum Under Counter Clearance (Width) ETT304-1 ETT /2 (77.5 cm) 36 1/2 (92.7 cm) 3 /4 1 1 / / 2 3 /4 UNDER COUNTER CLERNCE TOP VIEW VENTILTION CUTOUT Cabinets that are: () Overhead Clearances: ll Installations Directly above cooking surface 1 To left or right of cooking surface 1, 2 30 (76.2 cm) 18 (45.7 cm) Rear wall 6" (15.2 cm) min. from mounting surface to combustibles below cooktop chassis C Model (C) Cutout Width: Installations without Downdraft Vent 2 1/4 min. (5.7 cm) 19 3/4 (50.2 cm) ETT304-1 ETT /4 (73.0 cm) 34 3/4 (88.3 cm) 1 min. (2.5 cm) 6 (15.2 cm) min. to combustible, side wall, both sides COUNTERTOP CUTOUT (WITHOUT DOWNDRFT VENT) 3.7

30 ETT304-1, ETT365-2 Renaissance 30 and 36 Wide, Electric Cooktops Revised 10/20/14 ll tolerances: +1/16 (+1.6 mm), -0, unless otherwise stated. 3/8 min. (1.0 cm) flat countertop overhang required behind cutout Countertop 5/8 min. (1.6 cm) flat countertop overhang required behind cutout Countertop Stiffener ETT or MET series cooktop Stiffener ETT or MET series cooktop Cabinet face 3/8 min. (1.0 cm) space behind downdraft vent chassis to clear stiffener ERV or PRV series downdraft vent: Check downdraft vent specifications to determine proper fit Cabinet face 5/8 min. (1.6 cm) space behind downdraft vent chassis to clear stiffener RV series downdraft vent: Check downdraft vent dimensions/specifications to determine proper fit 4 5/8 (11.7 cm) 9 7/8 (25.1 cm) with CP3 blower installed Floor Floor ERV ND PRV SERIES DOWNDRFT VENT INSTLLTION SIDE VIEW RV SERIES DOWNDRFT VENT INSTLLTION - SIDE VIEW E C F Rear wall D 19 3/4" (50.2 cm) Cabinet face 1" min. (2.5 cm) 6" (15.2 cm) min. from mounting surface to combustibles below cooktop chassis 6" min. (15.2 cm) 6" min. (15.2 cm) COUNTERTOP CUTOUT (WITH DOWNDRFT VENT) TOP VIEW Cabinets that are: Directly above cooking surface 1 To left or right of cooking surface 1, 2 COUNTERTOP CUTOUT (WITH DOWNDRFT VENT) ISO VIEW () Overhead Clearances: ll Installations 30 (76.2 cm) 18 (45.7 cm) Model/Configuration () Cooktop Cutout Width (C) Downdraft Vent Cutout Width (D) Total Cutout Depth (E) Downdraft Vent Cutout Depth (F) Minimum Rear Countertop Overhang ETT304-1 cooktop with ERV30[15] or PRV30 downdraft vent 28 3/4 27 3/4 22 1/2 (57.2 cm) 2 3/4 (7.0 cm) 3/8 (1.0 cm) ETT304-1 cooktop with RV30 downdraft vent (73.0 cm) (70.5 cm) 22 1/4 (56.5 cm) 2 1/2 (6.4 cm) 5/8 (1.6 cm) ETT365-2 cooktop with ERV36[15] or PRV36 downdraft vent 34 3/4 33 3/4 22 1/2 (57.2 cm) 2 3/4 (7.0 cm) 3/8 (1.0 cm) ETT365-2 cooktop with RV36 downdraft vent (88.3 cm) (85.7 cm) 22 1/4 (56.5 cm) 2 1/2 (6.4 cm) 5/8 (1.6 cm) 3.8

31 RNCT304, RNCT365 Renaissance 30 and 36 Wide, Electric Induction Cooktops Revised 10/20/14 WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. Product tolerances: ±1/16 (±1.6 mm) unless otherwise noted 30 2 (76.2 cm) Glass thickness: 3/16 (4.8 mm) 3 7/8 (9.8 cm) (48.3 cm) 1 (53.3 cm) 2 28 (72.4 cm) (91.4 cm) Glass thickness: 3/16 (4.8 mm) 3 7/8 (9.8 cm) PRODUCT DIMENSIONS - RNCT (48.3 cm) 1 2 (53.3 cm) 34 (86.4 cm) 1 PRODUCT DIMENSIONS - RNCT365 1 Chassis depth is 1/2 wider/deeper at base of glass cooking surface assembly. 2 Cooking surface overhangs top of chassis by 3/4 (1.9 cm) in front, back and on both sides. Model No. RNCT304 RNCT365 Total Connected Load* 31.0 mp kw 44.0 mp kw Dedicated Circuit Requirement 240 Vac, 60 Hz. 3 wire** 40 mp. 240 Vac, 60 Hz. 3 wire** 50 mp. * These specifications are for reference only. See the product data label for exact specifications. ** Two 120 Vac hot (L1 and L2) and one ground (all copper). ELECTRICL SUPPLY REQUIREMENTS 3.9

32 RNCT304, RNCT365 Renaissance 30 and 36 Wide, Electric Induction Cooktops Revised 10/20/14 Cabinet tolerances: +1/16 (+1.6 mm), -0 unless otherwise stated To reduce the risk of personal injury caused by reaching over a hot appliance, cabinet storage space located directly above the cooktop should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood. Locate the junction box within reach of the included 48 inch long (122 cm) cooktop power conduit attached at the bottom right rear of the chassis. Make sure the underside of the cooktop and the junction box are accessible for inspection/service. To reduce the risk of personal injury and to reduce accumulated smoke in the room, Dacor strongly recommends installing a range hood. Install the range hood according to the accompanying installation instructions. range hood should cover the entire cooking surface below and project horizontally a minimum of 5 inches beyond the bottom of overhead cabinets. lways consult the countertop manufacturer for specific installation instruction or requirements. NOTE: The countertop opening must accept square corners of the cooktop. Some installations may require the installation of fire retardant materials (see notes below). Flame retardant materials bear the mark: UNDERWRITERS LORTORIES INC. CLSSIFIED MINERL ND FIER ORDS. SURFCE URNING CHRCTERISTICS This mark is followed by the flame spread and smoke ratings. These designations are shown as FHC (Flame Spread)/(Smoke Developed). Material with 0 flame spread rating are flame retardant. Local codes may allow other flame spread ratings. If the cooktop chassis is completely enclosed, provide ventilation of 7 square inches minimum into the enclosure. See following page for flush and downdraft vent installation cutouts. 13 (33.0 cm) max (45.7 cm) min. 3 Note 4 To allow for ventilation, maintain a minimum of 5 3/4 (14.6 cm) clearance between the top of the counter and NY surface below, including the upper edge of any drawers below. lso maintain a clearance of 2 (5.1 cm) between the vents on the front of the chassis and the cabinet. Countertop 19 3/4 (50.2 cm) 5 3/4 (14.6 cm) min. Non-combustible surface along back wall recommended Cooktop UNDER COUNTER CLERNCE Note 1 Note 5 Grate level 2 gap (5.1 cm) min. Front cabinet face 1 1/2 (3.8 cm) max. countertop thickness Note 2 CINET CUTOUT DIMENSIONS 1 30 inches minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet or = 24 inches minimum when the bottom of wood or metal cabinet is protected by not less than 1/4 inch thick flame retardant material covered with not less than #28 gage sheet steel,.015 inch thick stainless steel,.024 inch thick aluminum, or.020 inch thick copper. 2 Distance to combustible side wall (both sides): 2 7/8 (7.3 cm) min. from edge of cutout, 2 1/4 (5.7 cm) min. from edge of cooking surface. 3 This specification not applicable for cabinets more than a horizontal distance of 2 1/4 (5.7 cm) from edge of cooktop, when installed /8 (2.9 cm) min. to combustible surface to rear. 3/4 (1.9 cm) min. to non-combustible surface to rear. 5 Make sure proper internal spacing is maintained to allow for under-cabinet (chassis) ventilation. See diagram above. Model () () RNCT304 RNCT (76.2 cm) 36 (91.4 cm) 28 3/4 (73.0 cm) 34 3/4 (88.3 cm) 3.10

33 RNCT304, RNCT365 Renaissance 30 and 36 Wide, Electric Induction Cooktops Revised 10/20/14 Cabinet tolerances: +1/16 (+1.6 mm), -0 unless otherwise stated Countertop 3/16 (4.8 mm) 11/16 (7.0 mm) IMPORTNT: See previous page for minimum clearances to combustibles and overhead cabinets. Countertop Inset (side view) 19 3/4 (50.2 cm) Model () () RNCT304 RNCT /8 (76.5 cm) 36 1/8 (91.8 cm) 28 3/4 (73.0 cm) 34 3/4 (88.3 cm) 21 1/8 (53.7 cm) FLUSH INSTLLTION CUTOUT DIMENSIONS (COOKING SURFCE EVEN WITH COUNTERTOP) F D G IMPORTNT: See previous page for minimum clearances to combustibles and overhead cabinets. Install only the downdraft vent models specified in the table below. E 19 3/4" (50.2 cm) C Cabinet face If installing the cooktop and downdraft vent flush to the countertop, use the countertop inset dimensions shown above for the cooktop. The countertop inset for the downdraft vent will need to be lower to accommodate the top cap, which is different from model to model. Determine the inset depth from the product dimensions in the downdraft vent installation instructions. dditional sealing will be required between the cooktop chassis and the downdraft vent due to the difference in inset depth required. Model/Configuration (C) Cooktop Cutout Width (D) Vent Cutout Width (E) Total Cutout Depth (F) Vent Cutout Depth (G) Minimum Rear Countertop Overhang RNCT304 with ERV30[15]/PRV30 downdraft vent 28 3/4 27 3/4 22 1/2 (57.2 cm) 2 3/4 (7.0 cm) 3/8 (1.0 cm) RNCT304 with RV30 downdraft vent (73.0 cm) (70.5 cm) 22 1/4 (56.5 cm) 2 1/2 (6.4 cm) 5/8 (1.6 cm) RNCT365 with ERV36[15]/PRV36 downdraft vent 34 3/4 33 3/4 22 1/2 (57.2 cm) 2 3/4 (7.0 cm) 3/8 (1.0 cm) RNCT365 with RV36 downdraft vent (88.3 cm) (85.7 cm) 22 1/4 (56.5 cm) 2 1/2 (6.4 cm) 5/8 (1.6 cm) RNCT COOKTOP WITH DOWNDRFT VENT CUTOUT DIMENSIONS (TOP VIEW) 3.11

34 SGM304, SGM365, SGM466 Classic 30, 36 and 46 Wide, Drop-in Gas Cooktops Revised 10/20/14 ll tolerances ±1/16 (±1.6 mm), unless otherwise noted. WRNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. This appliance must be installed in accordance with the accompanying installation instructions. 30" (76.2 cm) 1 5/8" (4.1 cm) bottom of base to cooking surface 4" (10.2 cm) chassis height 21" (53.3 cm) 19 1/2" * (49.5 cm) * including embosses/screws in side of chassis 27 5/8" * (70.2 cm) 36" (91.4 cm) PRODUCT DIMENSIONS - MODEL SGM /8" (4.1 cm) bottom of base to cooking surface 4" (10.2 cm) chassis height 21" (53.3 cm) 19 1/2" * (49.5 cm) 33 1/2" * (85.1 cm) PRODUCT DIMENSIONS - MODEL SGM365 * including embosses in side of chassis 46" (116.8 cm) 4" (10.2 cm) chassis height 1 5/8" (4.1 cm) bottom of base to cooking surface 21" (53.3 cm) 19 1/2" * (49.5 cm) 44 5/8" * (113.3 cm) PRODUCT DIMENSIONS - MODEL SGM466 * including embosses/screws in side of chassis 4.1

35 SGM304, SGM365, SGM466 Classic 30, 36 and 46 Wide, Drop-in Gas Cooktops Revised 10/20/14 Electrical Requirements WRNING To prevent an electric shock hazard, the power supply must meet the specifications stated below. It is the owner s responsibility to make sure that the electrical service meets electrical requirements and that the electrical outlet has been properly installed. The cooktop is supplied with a factory installed, 40-inch, three-prong, grounding electrical plug. It is connected to the chassis at the bottom right rear corner (see Chassis ottom Diagram below). It must be connected to a dedicated, grounded three-prong electrical outlet installed by a licensed electrician. The electrical installation, including minimum supply wire size and grounding, must be done in accordance with National Electric Code NSI/NFP 70* and local codes and ordinances. copy of this standard may be obtained from: National Fire Protection ssociation 1 atterymarch Park Quincy, Massachusetts The correct voltage, frequency and amperage must be supplied to the electrical outlet according to the product data label located on the bottom of the chassis. See the Gas and Electrical Requirements table on this page for reference. e certain to locate the electrical outlet so that the power cord may be easily disconnected if the unit needs service. Front of unit Product data label Electric cord CHSSIS OTTOM DIGRM Gas inlet Gas Supply Requirements e certain that the cooktop being installed is correct for the gas service being provided (natural gas or LP gas). lso, if operating the cooktop at an altitude above 4000 ft. (1219 m) make sure it is equipped for high altitude operation. Units equipped for LP operation have LP in the model number listed on the product data label. See the Chassis ottom Diagram for label location. Units equipped for high altitude operation have an H at the end of the model number listed on the product data label. Check your local building codes for the proper method of installation. In the absence of local codes, this appliance should be installed in accordance with the National Fuel Gas Code NSI Z223.1/NFP 54. n external manual shut-off valve must be installed between the gas inlet and the cooktop for the purpose of turning on or shutting off gas to the appliance. The cooktop comes from the factory with a regulator in the shipping carton. Use only the regulator provided. The regulator must be installed in the gas line that runs from the cooktop gas inlet to the gas shut off valve. Models SGM304 and SGM365 come with a 1/2 regulator. Model SGM466 comes with a 3/4 regulator, approved for connection to a 1/2 house gas supply. The cooktop gas connection is located on the bottom of the cootktop in the back right corner as you face the front of the unit. See the Chassis ottom Diagram on this page. SGM304 SGM365 SGM466 SGM304LP SGM365LP SGM466LP Gas type Natural LPG Manifold pressure Min. gas supply pressure** Max. gas supply pressure Total connected load Circuit requirement 4 Water column 10 Water column 5 Water column 11 Water column 1/2 psi 1/2 psi 0.25 mp. (0.03 kw) 120 Vac, 60 Hz, 15 mp mp. (0.03 kw) 120 Vac, 60 Hz, 15 mp. GS ND ELECTRICL REQUIREMENTS* * The electrical and gas data on this page is for reference only. If the above data does not agree with the product data label, use the data on the product data label. ** The gas supply pressure for testing the regulator setting shall be at least 1 inch water column (249 Pa) above the specified manifold pressure. 4.2