irad Wireless Controller

Transcription

1 irad Wireless Controller The irad Wireless Controller is a wireless (433MHz) programmable thermostat giving high precision room temperature control. It also had a seven day programmer with up to six temperature settings per day. Each controller can control any number of irad electric radiators within a 30 metre radius. irad Wireless Controller IMPORTANT SAFETY INFORMATION FOR irads 1. irads should only be installed by a qualified electrician in strict accordance with current IEEE Wiring Regulations and all relevant Building Regulations. 2. DO NOT use outdoors. The irad is for use as an indoor only fixed appliance and is not for portable use. 3. DO NOT use where flammable gases or liquids are stored. 4. DO NOT operate the irad with wet hands. 5. DO NOT let children play with the irad. 6. DO NOT obstruct the air circulation around the irad or allow curtains, clothes or furniture to touch or cover any part of the casing. If you wish to use the irad to dry towels, you will need to order an irad towel radiator. 7. DO NOT use the irad if the flexible mains lead gets damaged. In the unlikely event that such damage occurs, the irad should only be removed by a qualified electrician. Please contact Feature Radiators to arrange for a replacement lead to be fitted. 8. DO NOT attempt to repair an irad. There are no user serviceable parts inside the unit. Putting batteries in your irad Wireless Controller Your irad Wireless Controller is supplied with two AA alkaline batteries. (To avoid the possibility of corrosion damage, always use new batteries. A pair of good quality alkaline batteries should last at least two years.) The low battery symbol appears when the batteries need replacing. The battery symbol will begin to flash if the batteries are not replaced within two weeks. The clock must be reset after changing the batteries, but all other settings will be unaffected.

2 Connecting your wireless controller to your irad electric radiator If you want an irad to be remotely controlled by an irad Wireless Controller or wirelessly connected to other irads, you need to establish a wireless connection between the controller and the irads. Before starting the following procedure, locate the small grey button on the reverse of the controller. You will need to press this during the following procedure to connect your wireless controller to your irad. You will need to remove the wall plate from the back of the controller to access the grey button as pictured below. 1) Switch your irad off. 2) Switch your irad on for three seconds then switch it off again. Ensure you have your wireless controller to hand and you have access to the grey button on the reverse before commencing step 3. 3) When you switch on your irad again, it will be listening for the wireless signal from the controller. (This is shown by the LED light on the irad flashing if the LED does not flash just continue through the procedure). Whilst the light is flashing, press the grey button on the reverse of the controller. When the irad has connected to the controller, the LED light should stay on permanently. (Please note if the target temperature of the room is higher than the actual temperature of the room, the irad will receive a signal to switch on and the LED will be RED instead of GREEN) 4) You will need to repeat this process for every irad you wish to connect to the irad Wireless Controller in order to create a Heating Zone. The table below shows the status of the irad when the LED indicator light is lit up and is not flashing. LED Indicator colour RED (Full power) ORANGE (Half power) GREEN (Standby) irad status Radiator is heating up on full power. Radiator is running in economy mode as the room temperature is almost at the target temperature. Radiator is receiving power, but not heating up. Please note that once your irad is connected, it should remain permanently connected unless you put it back into Manual Mode see Resetting the irad in Manual ON/OFF Mode on page 4. Positioning your irad Wireless Controller When positioning your irad Wireless Controller, please avoid the following: 1) Draughty places near windows; 2) Places immediately adjacent to any heat source; 3) In direct sunlight; 4) Places where the controller could become easily damaged (i.e. where it could be hit by a door); or 5) Places where the controller may become wet.

3 Setting the Time and Day 1. To set the clock, day and 12 or 24 hour mode, press HOLIDAY and BOOST buttons together. 2. The hour will start to flash. You can then adjust the hour with the up and down buttons located to the right hand side of the screen. Once the hour is set, press SELECT. 3. Then the minutes will start to flash. Adjust the minutes with the up and down buttons located to the right hand side of the screen. Once the minutes are set, press SELECT. 4. Then the day will start to flash. Adjust the day with the up and down buttons located to the right hand side of the screen. Once the day is set, press SELECT. 5. Then the 12 or 24 hour clock mode will start to flash. Select 12 or 24 hour mode using the up and down buttons located to the right hand side of the screen. When the day, time and 12 or 24 hour mode is set, press OK. The display will return to normal mode. Setting the 7 day programme Factory preset The controller is factory preset to the following 7 day programme: Day Times Temp Times Temp Times Temp Times Temp Monday 6:30 to 8:30 21 C 8:30 to 16:30 4 C 16:30 to 23:00 21 C 23:00 to Tues 4 C Tuesday 6:30 to 8:30 21 C 8:30 to 16:30 4 C 16:30 to 23:00 21 C 23:00 to Wed 4 C Wednesday 6:30 to 8:30 21 C 8:30 to 16:30 4 C 16:30 to 23:00 21 C 23:00 to Thurs 4 C Thursday 6:30 to 8:30 21 C 8:30 to 16:30 4 C 16:30 to 23:00 21 C 23:00 to Fri 4 C Friday 6:30 to 8:30 21 C 8:30 to 16:30 4 C 16:30 to 23:00 21 C 23:00 to Sat 4 C Saturday 8:00 to 23:00 21 C 23:00 to Sun 4 C Sunday 8:00 to 23:00 21 C 23:00 to Mon 4 C

4 Changing the 7 day programme from the factory preset If you want to change the 7 day programme from the factory preset shown above, then follow the instructions below. You can set up to 6 temperature/time programmes per day but these cannot overlap. To set the 7 day programme, press SET-BACK and ADVANCE buttons together, which will take you to programme edit mode. This will take you to step 1 below. You can scroll through to any day and programme you like, but please note that the programme edit mode will always begin on the current day, time and programme. There are six programmes per day, which you will need to scroll through to get to the next day you wish to set. For the purpose of illustration, the diagrams below show Saturday, PROG. 1, 8:00am, 21 C. Copy Day function 1. The day and programme will begin to flash. You can move up and down through the day and program with the up and down buttons located at the right hand side of the screen. Once the day and programme have been chosen, press SELECT. This takes you to stage 2 2. The time flashes. Select the time for the chosen programme. You can move up and down through the time with the up and down buttons located at the right hand side of the screen. Once you have set the time for your chosen program, press SELECT. 3. The temperature flashes. Select the temperature required for your chosen programme. You can adjust the temperature up and down with the up and down buttons located at the right hand side of the screen. 4. When you have set the programme, either press SELECT to return to the day OR, if finished, press OK to return the controller to normal operation. For convenience, you can copy any day s programme to another day. For example, if you have set the program for Monday and would like the same programme from Monday to Friday, you can use the COPY DAY function to do this. To set the 7 day programme using the COPY DAY function, press SET-BACK and ADVANCE together, which will take you to programme edit mode. This will take you to step 1 below. 1. The day and programme will begin to flash. Select the day you wish to copy using the up and down buttons at the right hand side of the screen. Once the day has been selected, press COPY DAY. 2. The day for the programme to be copied to will begin to flash. Select the day required by using the up and down buttons located at the right hand side of the screen. Once your chosen day is selected, press COPY DAY. 3. Once copied, the next day will automatically come up on the screen. If you wish to copy your programme to this day, press COPY DAY. Do this as many times as required to copy the programme to your chosen days. 4. Once finished, press CLEAR. This will return you to the programme edit screen. If you have finished editing your programme, press OK, which will return the controller to normal operation mode.

5 Clearing a programme To clear a programme, press SET-BACK and ADVANCE together, which will take you to programme edit mode. Press CLEAR to clear a programme and press CLEAR again to unclear it. If you have cleared a programme, it displays as --:--, --.- C. If you clear all 6 programmes in all 7 days, there is no programme at all. The temperature will then be done entirely by Quick Adjust see below. Explanation of the buttons on an irad Wireless Controller The radio transit symbol appears whenever the irad Wireless Controller transmits to your irad. This happens about once per minute. Locking the controller You can lock the irad Wireless Controller to prevent tampering. When locked all buttons are disabled. HOLIDAY, BOOST, SET-BACK, ADVANCE, up and down arrow symbols are not displayed. To lock it press SET-BACK and ADVANCE together to enter programme setting, then press the button on the back for 2 seconds. To unlock press SET-BACK and ADVANCE together, release them, then press the button on the back within 2 seconds. Actual and Target Temp Actual is a thermometer showing the room temperature. Target is the temperature you would like. It is set manually or by the programme and can be when no heating is needed. Quick Adjust During normal operation you can use the up and down arrows to alter the temperature. The effect is temporary; it reverts to normal temperature on the next programme or when you press other buttons. You can set it to (no heating), or anything from 4 C (frost protection) to 30 C. HOLIDAY (no programme) Pressing HOLIDAY switches the programme off while you are away. Use the up and down arrows to alter the temperature. You can choose (no heating), 4 C (frost protection) or anything up to 12 C. It stays like this until you press CLEAR. BOOST (full power) Press BOOST to turn the irad on full power for an hour. If you press BOOST again it adds another hour up to a maximum of 4 hours. You can use the up and down arrows to adjust the minutes. Boost ends when the time runs out, or you can cancel it by pressing CLEAR. ADVANCE (early bird) Press ADVANCE if you wish to bring forward the next programme for instance if you arrive in or leave the room earlier than normal. The programme stays Advanced until the programme s normal time or until you press CLEAR. SET-BACK (economy) For economy press SET-BACK. The 7 day programme continues to run but all temperatures (except frost) are lowered by 5 C. Set-Back continues until you press CLEAR. Resetting the irad to MANUAL ON/OFF MODE Manual ON/OFF Mode allows you to switch the irad radiators on or off manually, by flicking the ON/OFF switch on the irad or spur on the wall. Ensure irad is switched off. Switch on for about three seconds then switch it off again. Do this 5 times in succession. Your irad should then be back to manual control mode. If the irad does not revert to manual mode after following the above instructions, call Feature Radiators technical helpline directly on No maintenance required irad electric radiators do not require maintenance, as they have no user serviceable parts. Cleaning advice To clean irads, simply wipe with a soft, damp cloth. Brushed stainless steel heaters often clean well when wiped with a soft cloth and a little baby oil. DO NOT use any abrasive materials or chemicals as these will damage the finish of the radiator. Ensure that the irad is switched off when cleaning. IMPORTANT SAFETY INFORMATION FOR irads

6 9. irads should only be installed by a qualified electrician in strict accordance with current IEEE Wiring Regulations and all relevant Building Regulations. 10. DO NOT use outdoors. The irad is for use as an indoor only fixed appliance and is not for portable use. 11. DO NOT use where flammable gases or liquids are stored. 12. DO NOT operate the irad with wet hands. 13. DO NOT let children play with the irad. 14. DO NOT obstruct the air circulation around the irad or allow curtains, clothes or furniture to touch or cover any part of the casing. If you wish to use the irad to dry towels, you will need to order an irad towel radiator. 15. DO NOT use the irad if the flexible mains lead gets damaged. In the unlikely event that such damage occurs, the irad should only be removed by a qualified electrician. Please contact Feature Radiators to arrange for a replacement lead to be fitted. 16. DO NOT attempt to repair an irad. There are no user serviceable parts inside the unit. WARRANTY AND AFTER-SALES SERVICE irad electric radiators are sold with a 2 year manufacturer s warranty. Whilst under warranty, Feature Radiators will arrange for repair or exchange of any faulty product, without charge, provided it has been handled, installed and operated in accordance the instructions provided and has not otherwise been misused or handled. Outside the warranty period, please contact Feature Radiators for an estimate of repair and associated costs. The power supply cord/flex of this appliance can only be replaced by opening the sealed panel. Accordingly any repair involving the cord/flex, should only be carried out by the manufacturer, otherwise the manufacturer s warranty will be invalidated. There are no user serviceable parts inside the irad. For after-sales service or repairs, contact Feature Radiators technical helpline directly on It would assist us when taking your call if you can have available your reference number (this can be found on the top right hand corner of your receipt) and details of the fault. Please do not return a product you consider faulty without obtaining the prior approval of Feature Radiators. Your rights under this warranty do not affect your statutory rights.