Product Information and Technical Guide

Transcription

1 Product Information and Technical Guide Side by Side and Top Mount Refrigerators January March 2004 White-Westinghouse July 2004

2

3 TABLE OF CONTENTS Safe Servicing Practices Service Data Sheet, Refrigerant Charge & Energy Efficiency Rating Indexes Troubleshooting Guide Appendix A - Service Data Sheets A1 - A A3 - A A5 - A A7 - A A9 - A A11 - A A13 - A A15 - A A17 - A A19 - A A21- A A

4 SAFE SERVICING PRACTICES - ALL APPLIANCES To avoid personal injury and/or property damage, it is important that Safe Servicing Practices be observed. The following are some limited examples of safe practices: 1. DO NOT attempt a product repair if you have any doubts as to your ability to complete it in a safe and satisfactory manner. 2. Before servicing or moving an appliance: Remove the power cord from the electrical outlet, trip the circuit breaker to the OFF position, or remove the fuse. Turn off the gas supply. Turn off the water supply. 3. Never interfere with the proper operation of any safety device. 4. USE ONLY REPLACEMENT PARTS CATALOGED FOR THIS APPLIANCE. SUBSTITUTIONS MAY DEFEAT COMPLIANCE WITH SAFETY STANDARDS SET FOR HOME APPLIANCES. 5. GROUNDING: The standard color coding for safety ground wires is GREEN, or GREEN with YELLOW STRIPES. Ground leads are not to be used as current carrying conductors. It is EXTREMELY important that the service technician reestablish all safety grounds prior to completion of service. Failure to do so will create a hazard. 6. Prior to returning the product to service, ensure that: All electrical connections are correct and secure All electrical leads are properly dressed and secured away from sharp edges, high-temperature components, and moving parts All non-insulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal parts and panels All safety grounds (both internal and external) are correctly and securely connected All panels are properly and securely reassembled ATTENTION!!! This service manual is intended for use by persons having electrical and mechnical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. Electrolux Home Products, Inc. cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the use of this manual Electrolux Home Products, Inc. 2

5 Model Service Data Sheet Charge Energy Efficiency Rating Brand CRTE151AQ Crosley CRTE151AW Crosley CRTE171AQ Crosley CRTE171AW Crosley CRTE183AQ Crosley CRTE183AW Crosley CRTE187AK Crosley CRTE187AS Crosley E23CS75DSS Electrolux FRS23BH6CS Frigidaire FRS23F4CB Frigidaire FRS23F4CQ Frigidaire FRS23F4CQ Frigidaire FRS23F4CW Frigidaire FRS23F4CW Frigidaire FRS23FCDB Frigidaire FRS23FCDQ Frigidaire FRS23FCDW Frigidaire FRS23H5DSB Frigidaire FRS23H7CB Frigidaire FRS23H7CQ Frigidaire FRS23H7CW Frigidaire FRS23KF6CB Frigidaire FRS23KF6CQ Frigidaire FRS23LH5DS Frigidaire FRS23LH5DW Frigidaire FRS23R4CB Frigidaire FRS23R4CB Frigidaire FRS23R4CQ Frigidaire FRS23R4CQ Frigidaire FRS23R4CW Frigidaire FRS23R4CW Frigidaire FRS23W3AQB Frigidaire FRS23W3AQC Frigidaire FRS23W3AWB Frigidaire FRS23W3AWC Frigidaire FRS26BH6CW Frigidaire FRS26DR7DS Frigidaire FRS26F4CB Frigidaire FRS26F4CB Frigidaire FRS26F4CQ Frigidaire FRS26F4CQ Frigidaire FRS26F4CW Frigidaire FRS26F4CW Frigidaire FRS26FCDB Frigidaire FRS26FCDQ Frigidaire FRS26FCDW Frigidaire FRS26H7CQ Frigidaire FRS26H7CW Frigidaire FRS26HF6BB Frigidaire FRS26HF6BQ Frigidaire FRS26HR4DB Frigidaire FRS26HR4DQ Frigidaire FRS26HR4DW Frigidaire FRS26LF7DS Frigidaire FRS26LF8CB Frigidaire 3

6 Model Service Data Sheet Charge Energy Efficiency Rating Brand FRS26LF8CQ Frigidaire FRS26LH5DB Frigidaire FRS26LH5DQ Frigidaire FRS26LH5DS Frigidaire FRS26LH5DW Frigidaire FRS26R2AQ Frigidaire FRS26R2AQ Frigidaire FRS26R2AW Frigidaire FRS26R2AW Frigidaire FRS26R4CB Frigidaire FRS26R4CB Frigidaire FRS26R4CQ Frigidaire FRS26R4CW Frigidaire FRS26R4CW Frigidaire FRS26RBCW Frigidaire FRS26RBCW Frigidaire FRS26RLECS Frigidaire FRS26RLECS Frigidaire FRS26W2AQ Frigidaire FRS26W2AW Frigidaire FRS26W2AW Frigidaire FRT14A2AW Frigidaire FRT14A2AZ Frigidaire FRT15A2DW Frigidaire FRT15A2DZ Frigidaire FRT15B1BW Frigidaire FRT15B3AQ Frigidaire FRT15B3AT Frigidaire FRT15B3AW Frigidaire FRT15B3AZ Frigidaire FRT15G4BQ Frigidaire FRT15G4BW Frigidaire FRT15HB3DQ Frigidaire FRT15HB3DW Frigidaire FRT15HB3DZ Frigidaire FRT17A2AQ Frigidaire FRT17A2AW Frigidaire FRT17A2AZ Frigidaire FRT17B3AQ Frigidaire FRT17B3AT Frigidaire FRT17B3AW Frigidaire FRT17B3AZ Frigidaire FRT17G4BD Frigidaire FRT17G4BQ Frigidaire FRT17G4BW Frigidaire FRT18B1BW Frigidaire FRT18B4AQA Frigidaire FRT18B4AWA Frigidaire FRT18B4AZA Frigidaire FRT18B5ABB Frigidaire FRT18B5AQB Frigidaire FRT18B5AWB Frigidaire FRT18B6CB Frigidaire FRT18G4AQC Frigidaire FRT18G4AWC Frigidaire FRT18G7CW Frigidaire 4

7 Model Service Data Sheet Charge Energy Efficiency Rating Brand FRT18H6CB Frigidaire FRT18H6CQ Frigidaire FRT18H6CSB Frigidaire FRT18H6CSK Frigidaire FRT18H6CW Frigidaire FRT18HB5DW Frigidaire FRT18HS6AB Frigidaire FRT18HS6DB Frigidaire FRT18HS6DQ Frigidaire FRT18HS6DW Frigidaire FRT18IB4AQA Frigidaire FRT18IB4AWA Frigidaire FRT18IB4AZ Frigidaire FRT18IB4AZA Frigidaire FRT18IG4AQA Frigidaire FRT18IG4ATA Frigidaire FRT18IG4AWA Frigidaire FRT18IG4AZA Frigidaire FRT18IL6DQ Frigidaire FRT18IL6DS Frigidaire FRT18IL6DW Frigidaire FRT18IS6CB Frigidaire FRT18KB2CW Frigidaire FRT18KG3CW Frigidaire FRT18KG4CW Frigidaire FRT18LN5BQ Frigidaire FRT18LN5BW Frigidaire FRT21BH8CB Frigidaire FRT21BH8CS Frigidaire FRT21BH8CW Frigidaire FRT21BSDSB Frigidaire FRT21C5AQ Frigidaire FRT21C5AW Frigidaire FRT21FG3CQ Frigidaire FRT21FG3CW Frigidaire FRT21FG4CQ Frigidaire FRT21FG4CW Frigidaire FRT21G3CW Frigidaire FRT21G3CW Frigidaire FRT21G4BQ Frigidaire FRT21G4BW Frigidaire FRT21H7ASB Frigidaire FRT21H7ASK Frigidaire FRT21H8CB Frigidaire FRT21H8CQ Frigidaire FRT21H8CSB Frigidaire FRT21H8CSK Frigidaire FRT21H8CW Frigidaire FRT21HS6AW Frigidaire FRT21HS6DB Frigidaire FRT21HS6DQ Frigidaire FRT21HS6DW Frigidaire FRT21IL5DQ Frigidaire FRT21IL5DW Frigidaire FRT21KG3CW Frigidaire FRT21KG4CW Frigidaire 5

8 Model Service Data Sheet Charge Energy Efficiency Rating Brand FRT21KS6CQ Frigidaire FRT21LR7AB Frigidaire FRT21LR7AQ Frigidaire FRT21LR7AW Frigidaire FRT21LR8DS Frigidaire FRT21P5ABA Frigidaire FRT21P5AQA Frigidaire FRT21P5AWA Frigidaire FRT21P6CQ Frigidaire FRT21P6CSB Frigidaire FRT21P6CSK Frigidaire FRT21P6CW Frigidaire FRT21S6AB Frigidaire FRT21S6AW Frigidaire GLHS237ZCW Frigidaire GLHS269ZCB Frigidaire GLRS237ZCB Frigidaire GLRS237ZCB Frigidaire GLRS237ZCQ Frigidaire GLRS237ZCQ Frigidaire GLRS237ZCW Frigidaire GLRS237ZCW Frigidaire GLRS267ZCB Frigidaire GLRS267ZCB Frigidaire GLRS267ZCQ Frigidaire GLRS267ZCQ Frigidaire GLRS267ZCW Frigidaire GLRS267ZCW Frigidaire GLRT183TDB Frigidaire GLRT183TDB Frigidaire GLRT183TDQ Frigidaire GLRT183TDW Frigidaire GLRT184TCB Frigidaire GLRT185TDB Frigidaire GLRT185TDB Frigidaire GLRT185TDK Frigidaire GLRT185TDQ Frigidaire GLRT185TDS Frigidaire GLRT185TDW Frigidaire GLRT212IDB Frigidaire GLRT212IDB Frigidaire GLRT212IDQ Frigidaire GLRT212IDQ Frigidaire GLRT212IDW Frigidaire GLRT212IDW Frigidaire GLRT214TCB Frigidaire GLRT214TCQ Frigidaire GLRT214TCW Frigidaire GRS23R4CQ Frigidaire GS18HTZCQ Frigidaire GS18HTZCW Frigidaire GS18HTZDB Frigidaire GS18HTZDSB Frigidaire GS18HTZDSK Frigidaire GS18HTZDW Frigidaire GS23HSZCC Frigidaire 6

9 Model Service Data Sheet Charge Energy Efficiency Rating Brand GS23HSZCQ Frigidaire GS26HSZCC Frigidaire GS26HSZCQ Frigidaire PLHT189CSB Frigidaire PLHT189CSK Frigidaire PLHT219TCB Frigidaire PLHT219TCK Frigidaire FSC23F7DB Frigidaire-CD PHSC239DSB Frigidaire-CD GRT15B3BW Gibson GRT17B3BQ Gibson GRT17B3BW Gibson GRT17G4BQ Gibson GRT17G4BW Gibson GRT21G3CW Gibson GRT21S6CW Gibson WRS23MF5ASA W / W WRS23MW3AQA W / W WRS23MW3AW W / W WRS23MW3AWA W / W WRS23W0AWA W / W WRS23W0AWB W / W WRT15A0AW W / W WRT15MB3AW W / W WRT15MG4BQ W / W WRT17MB3AW W / W WRT17MG4BQ W / W WRT18A0AWA W / W WRT21MG3AQ W / W WRT21MG3AW W / W WRT21MP5AQ W / W WRT21MP5AW W / W WRT21MR7AS W / W WRT21S4AW W / W 7

10 TROUBLESHOOTING GUIDE PROBLEM CAUSE SOLUTION Compressor will not run. Compressor runs but does not cool. No voltage at wall receptacle. Service cord defective or unplugged at wall receptacle. Low voltage causing compressor to cycle on overload. Control thermostat knob in OFF position. Inoperative control thermostat. Compressor stuck. Compressor windings open. Defrost timer stuck in defrost mode. ADC (Adaptive Defrost Control) not turning on compressor after defrost. Compressor overload stuck open. Relay lead loose. Relay loose or inoperative. Service cord pulled out of harness. Faulty cabinet wiring. Check circuit breaker, fuse or GFCI (Ground Fault Circuit Interruptor - It is not recommended to connect your refrigerator to a GFCI.) Check service cord. Voltage fluctuation should not exceed ± 10% of vac ( ) Turn control thermostat knob to ON position. Replace control thermostat Replace compressor. Replace compressor. Replace defrost timer. (if equipped) Replace ADC. Replace compressor overload. (if equipped compressor starter relay & overload may be plugged into each other) Repair or replace lead. Repair or replace relay. (if equipped) Repair connection. Repair wiring. System out of refrigerant. Check for leaks. * Compressor not pumping. Replace compressor. * Restricted filter drier. Replace filter drier. * Restricted capillary tube. Replace heat exchanger and evaporator assembly. Moisture in system. See NOTE. * * NOTE: Repair or replace component that is leaking. Replace the compressor if the system is contaminated. Blow out remaining part of system with dry Nitrogen. Pump down and recharge per listing on product serial label. Always replace filter drier when repairing sealed system. 8

11 PROBLEM CAUSE SOLUTION Compressor short cycles. Compressor runs too much. Noisy. Erratic control thermostat. Faulty relay. Restricted air flow over condenser. Low voltage fluctuation exceeds ± 10% of vac ( ). Compressor draws excessive watts. Inoperative condenser fan motor. Control thermostat is erratic or not properly set. Refrigerator exposed to high heat. (110 or higher) High room temperature. (110 F or higher) Low pumping capacity compressor. Door gaskets not sealing. Replace control thermostat. Replace relay or starter. Ensure air flow is unobstructed over condenser. Call qualified electrician. Replace compressor. Replace condenser fan motor. Replace control thermostat or reset to normal position. Move refrigerator to cooler location. Advise customer not to install refrigerator where temperature will rise above 110 F because compressor will not maintain proper temperatures. Replace compressor. System undercharged. Check for leaks. * System overcharged. Adjust doors or replace door gaskets. Charge per listing on product serial plate. * Interior light stays on. Check door switch and door adjustment. Contaminants in system. Capillary tube kinked or partially restricted. Flush out system. Replace filter drier, evacuate, and recharge. * Replace heat exchanger and evaporator assembly. * Filter drier partially restricted. Replace filter drier. * Refrigerator and/or freezer compartment overloaded poor air circulation Restricted air flow over condenser. Condenser fan motor is inoperative. (Forced air condenser models only) Tubing vibrates. Internal compressor noise. Loose parts. Compressor operating at high head pressure due to restricted air flow over condenser. Advise customer. Ensure air flow is unobstructed over condenser. Replace condenser fan motor. Adjust tubing. Replace compressor. Check shelving. Ensure air flow is unobstructed over condenser. * See NOTE at bottom of page 8) 9

12 PROBLEM CAUSE SOLUTION Freezer compartment too warm. Fig. A Freezer compartment too cold. Inoperative evaporator fan motor. Improperly positioned fan blade. Check wiring and evaporator fan motor. (Check ADC on Side-by-Sides.) Position fan blade properly. See Figure A. Evaporated frosted up. Check defrost system, door adjustments, and door gaskets. Inoperative condenser fan motor. (Forced air condenser models only) Restricted air flow over condenser On static condensers, be sure you have 1 between condenser and wall, and 3 over top, or 1 side of condenser is clear. Freezer compartment overloaded poor air circulation. Replace condenser fan motor. Clean condenser. (Dynamic models only.) Advise customer. Low room temperature.(55 ) Advise customer not to install refrigerator where temperature will drop below 60 F. Compressor will not maintain proper temperatures. Freezer or refrigerator compartment doors left open. Control thermostat out of calibration. Door gaskets not sealing. Control thermostat capillary tube improperly positioned. Advise customer. Replace control thermostat. Shortage of refrigerant. Check for leaks. * Restricted filter drier or capillary tube. Evaporator fan motor covered in ice. Inoperative cold control. (Top mount-no Frost or Side-by-Side freezer cold control) Freezer compartment inlet air duct is loose or restricted. Door is loose. Food compartment air return duct blocked (Top Mount only) Diffuser (foam block) in top of food compartment is broken. (Foam block located in control housing.) 5 Adjust doors or replace door gaskets. Reposition temperature sensing element. Check for leaks and burnt compressor windings. * Check seal around ice maker fill spout. Check seal between evaporator cover and liner. (Side-by-sides only) Replace cold control. Re-install air duct or remove obstruction from inlet air duct. Adjust door. If foam block is frozen, replace block. If duct is blocked, remove obstruction. Replace diffuser. (Top Mount only) Freezer compartment cold control installed incorrectly. (Side-by-Sides only) * See NOTE at bottom of page 8 10

13 PROBLEM CAUSE SOLUTION Refrigerator compartment too warm. Refrigerator compartment too cold. Inoperative evaporator fan motor. Improperly positioned fan blade. Check wiring and evaporator fan motor. (Check ADC on Side-by-Sides.) Position fan blade properly. See page 10, Figure A. Evaporated frosted up. Check defrost system, door adjustments, and door gaskets. Refrigerator compartment overloaded poor air circulation. Advise customer. Low room temperature. (55 ) Advise customer not to install refrigerator where temperature will drop below 60 F. Compressor will not maintain proper temperatures. Freezer or refrigerator compartment doors left open. Damper control out of calibration or not opening. Advise customer. Replace damper control. Shortage of refrigerant. Check for leaks. * Restricted filter drier or capillary tube. Refrigerator compartment inlet air duct loose or restricted. Door is loose. Freezer compartment return air duct restricted. Control thermostat knob set at too warm a position. Inoperative or erratic refrigerator/freezer compartment door switch. Freezer compartment inlet air duct is loose or restricted. Door is loose. Food compartment air return duct blocked (Top Mount only) Inoperative cold control. Refrigerator compartment inlet air duct loose or restricted. Door is loose. Diffuser (foam block) in top of food compartment is broken. (Foam blocked located in control housing.) Check for leaks and burnt compressor windings. * Re-install air duct or remove obstruction from air duct. Adjust door. Remove obstruction from return air duct. Set control knob to a colder position. Replace door switch. Re-install air duct or remove obstruction from inlet air duct. Adjust door. If foam block is frozen, replace block. If duct is blocked, remove obstruction. Replace cold control. Re-install air duct or remove obstruction from air duct. Adjust door. Replace diffuser. (Top Mounts only) * See NOTE at bottom of page 8. 11

14 PROBLEM CAUSE SOLUTION Refrigerator compartment too cold. (Continued) Evaporator blocked with ice. (See Adaptive defrost Control) Frozen drain. Adaptive Defrost Control (ADC) not responding correctly. Inoperative cold control. Refrigerator compartment inlet air duct loose or restricted. Door is loose. Diffuser (foam block) in top of food compartment is broken. (Foam blocked located in control housing) Door in damper control not closing or not closing all the way. Cold air blowing into food compartment with damper door closed all the way. Inoperative defrost timer. Defrost thermostat terminates too early. Thermostat is open. Refrigerator/Freezer compartment doors left open. Open defrost heater. Air leak around ice maker fill tube, or opening. Ice maker water line and wiring harness openings not sealed. Drain trough not properly formed. Divider (foam block) frozen. Faulty ADC board. Bad wire between ADC, defrost heater, and limiter. Replace cold control. Re-install air duct or remove obstruction from air duct. Adjust door. Replace diffuser. (Top Mounts only) Replace damper control. Check freezer control bulb for correct positioning to ensure it is installed correctly. Check foam seal between damper housing and cabinet liner. Check to see that the control box is mounted flush against the cabinet liner. Check wiring. Repair or replace defrost timer. Check for correct positioning of defrost thermostat. Repair or replace. Advise customer. Replace heater. Seal with permagum. Seal water line and wiring harness openings. Ensure drain trough is at 90 angle to back of freezer and that lip is up on front and ends. Replace divider. Check drain trough. Replace ADC board. Check wiring and wiring connectors. 12

15

16 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING SERVICE DATA SHEET INFORMATION Type A With Run Capacitor 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 25 to 35% 45 to 55% Freezer Refrigerature 2 to 8 F -17 to -13 C 35 to 40 F 2 to 4 C 0 to 5 F -18 to -15 C 35 to 40 F 2 to 4 C STANDARD - AUTOMATIC DEFROST TOP FREEZER MODELS (R134a) IMPORTANT SAFETY NOTICE P/N: Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until Holding Switch circuit is completed. All components of ice maker should function to complete the cycle. L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 110 to 120 psig 758 to 827 kpa 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 150 to 175 psig 1034 to 1207 kpa (Last 1/3 of cycle) 140 to to 185 (Running) 1.1 to to 1. 6 Base Voltage Cabinet Size 18' & 21' DEFROST SPECIFICATIONS Cut-in 25 F -4 C VAC VAC Thermostat Cut-out 47 F 8 C Ohms The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing. IMPORTANT If any green grounding wires are moved during servicing, they must be returned to their original position and properly secured. CAUTION: All electrical parts and wiring must be shielded from torch flame. Do not allow torch to contact insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 95 to 105cc (3.2 to 3.6 oz.). When a water valve is replaced, the fill volume must be checked. A ', 15' & 17' 25 F -4 C 47 F 8 C Mechanical Timer - Defrost 30 Minutes Every 10 Hours of Compressor Run Time Electronic Timer (ADC) Defrost Up To 24 Minutes Every 6-72 Hours of Compressor Run Time CONDENSER FAN MOTOR RPM NOTE: This product comes equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds CW Opposite Shaft.15 Running SPECIFICATIONS Electrical Volts 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) 165 CONNECTOR PLUG CONNECTIONS Wire Number W ire Color Connects to: 1 Green/Yellow 2 Yellow 3 Black 4 Lt. Blue Ground Water Valve Line Neutral

17 Pictorial Schematic Ladder Schematic A - 2 Compressor Wiring

18 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING Type A With Run Capacitor 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 25 to 35% 45 to 55% Freezer Refrigerature L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 2 to 8 F -17 to -13 C 35 to 40 F 2 to 4 C 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 110 to 120 psig 758 to 827 kpa 0 to 5 F -18 to -15 C 35 to 40 F 2 to 4 C 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 150 to 175 psig 1034 to 1207 kpa (Last 1/3 of cycle) 140 to to 185 (Running) 1.1 to to 1. 6 STANDARD - AUTOMATIC DEFROST TOP FREEZER MODELS (R134a) SERVICE DATA SHEET P/N: IMPORTANT SAFETY NOTICE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing. IMPORTANT If any green grounding wires are moved during servicing, they must be returned to their original position and properly secured. INFORMATION Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until holding switch circuit is completed. All components of ice maker should function to complete the cycle. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 102 to 130cc (3.4 to 4.3 oz.). When a water valve is replaced, the fill volume must be checked. B ase Voltage VAC (127 VAC Max) VAC (127 VAC Max) Cabinet Size 18' & 21' DEFROST SPECIFICATIONS Cut-in 25 F -4 C Thermostat Cut-out 47 F 8 C Ohms CAUTION: All electrical parts and wiring must be shielded from torch flame. Do not allow torch to contact insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. A ', 15' & 17' 25 F -4 C 47 F 8 C Mechanical Timer - Defrost 30 Minutes Every 10 Hours of Compressor Run Time Electronic Timer (ADC) Defrost Up To 24 Minutes Every 6-72 Hours of Compressor Run Time CONDENSER FAN MOTOR RPM CW Opposite Shaft.15 Running SPECIFICATIONS NOTE: This product comes equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds. E lectrical VAC (127 VAC Max) 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) 165 Wire CONNECTOR PLUG CONNECTIONS Number 1 Green/Yellow 2 Yellow 3 Black 4 Lt. Blue W ire Color Connects to: Ground Water Valve Line Neutral LINE GRN / YEL P-3 P-1 THERMAL CUT-OUT GRN / YEL MOLD BRN MOUNTING PLATE MOTOR RED POWER MOLD HEATER 165 WATTS HOLD SWITCH C NC NO YEL THERMOSTAT C RED NO NC WATER FILL SWITCH BLU C NO NC SHUT-OFF SWITCH LT. BLU YEL RED NEUTRAL YEL P-4 P-2 WATER VALVE

19 Pictorial Schematic Ladder Schematic NOTE: DENOTES NOT ON ALL MODELS A - 4 COMPRESSOR WIRING Induction Run Compressor with Relay 15 & 17 CUBIC FOOT 18 CUBIC FOOT 21 CUBIC FOOT SERVICE PARTS STATIC DYNAMIC E-STAR STATIC DYNAMIC E-STAR DYNAMIC E-STAR Compressor / Kit * Starter/PTC * Run Capacitor * Relay N/A N/A N/A N/A N/A N/A Overload N/A N/A N/A N/A N/A N/A Control Timer (if applicable) ADC (if applicable) N/A N/A N/A N/A N/A N/A N/A N/A Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor N/A N/A

20 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING Type A With Run Capacitor 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 25 to 35% 45 to 55% Freezer Refrigerature L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 2 to 8 F -17 to -13 C 35 to 40 F 2 to 4 C 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 110 to 120 psig 758 to 827 kpa 0 to 5 F -18 to -15 C 35 to 40 F 2 to 4 C 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 150 to 175 psig 1034 to 1207 kpa (Last 1/3 of cycle) 140 to to 185 (Running) 1.1 to to 1. 6 STANDARD - AUTOMATIC DEFROST TOP FREEZER MODELS (R134a) SERVICE DATA SHEET P/N: IMPORTANT SAFETY NOTICE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing. IMPORTANT If any green grounding wires are moved during servicing, they must be returned to their original position and properly secured. INFORMATION Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until holding switch circuit is completed. All components of ice maker should function to complete the cycle. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 102 to 130cc (3.4 to 4.3 oz.). When a water valve is replaced, the fill volume must be checked. B ase Voltage VAC (127 VAC Max) VAC (127 VAC Max) Cabinet Size 18' & 21' DEFROST SPECIFICATIONS Cut-in 25 F -4 C Thermostat Cut-out 47 F 8 C Ohms CAUTION: All electrical parts and wiring must be shielded from torch flame. Do not allow torch to contact insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. A ', 15' & 17' 25 F -4 C 47 F 8 C Mechanical Timer - Defrost 30 Minutes Every 10 Hours of Compressor Run Time Electronic Timer (ADC) Defrost Up To 24 Minutes Every 6-72 Hours of Compressor Run Time CONDENSER FAN MOTOR RPM CW Opposite Shaft.15 Running SPECIFICATIONS NOTE: This product comes equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds. E lectrical VAC (127 VAC Max) 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) 165 Wire CONNECTOR PLUG CONNECTIONS Number 1 Green/Yellow 2 Yellow 3 Black 4 Lt. Blue W ire Color Connects to: Ground Water Valve Line Neutral LINE GRN / YEL P-3 P-1 THERMAL CUT-OUT GRN / YEL MOLD BRN MOUNTING PLATE MOTOR RED POWER MOLD HEATER 165 WATTS HOLD SWITCH C NC NO YEL THERMOSTAT C RED NO NC WATER FILL SWITCH BLU C NO NC SHUT-OFF SWITCH LT. BLU YEL RED NEUTRAL YEL P-4 P-2 WATER VALVE

21 Pictorial Schematic Ladder Schematic A - 6 NOTE: DENOTES NOT ON ALL MODELS COMPRESSOR WIRING Induction Run Compressor with Relay 15 & 17 CUBIC FOOT 18 CUBIC FOOT 21 CUBIC FOOT SERVICE PARTS STATIC DYNAMIC E-STAR STATIC DYNAMIC E-STAR DYNAMIC E-STAR Compressor / Kit * Starter/PTC * N/A N/A N/A Run Capacitor * N/A N/A N/A Relay N/A N/A N/A N/A N/A Overload N/A N/A N/A N/A N/A Control Timer (if applicable) ADC (if applicable) N/A N/A N/A N/A N/A N/A N/A N/A Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor N/A N/A * Typical compressor kit includes compressor, electrical components, and filter-drier

22 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING Type A With Run Capacitor 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 25 to 35% 45 to 55% Freezer Refrigerature L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 2 to 8 F -17 to -13 C 35 to 40 F 2 to 4 C 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 110 to 120 psig 758 to 827 kpa 0 to 5 F -18 to -15 C 35 to 40 F 2 to 4 C 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 150 to 175 psig 1034 to 1207 kpa (Last 1/3 of cycle) 140 to to 185 (Running) 1.1 to to 1. 6 STANDARD - AUTOMATIC DEFROST TOP FREEZER MODELS (R134a) SERVICE DATA SHEET P/N: IMPORTANT SAFETY NOTICE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing. IMPORTANT If any green grounding wires are moved during servicing, they must be returned to their original position and properly secured. INFORMATION Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until holding switch circuit is completed. All components of ice maker should function to complete the cycle. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 102 to 130cc (3.4 to 4.3 oz.). When a water valve is replaced, the fill volume must be checked. B ase Voltage VAC (127 VAC Max) VAC (127 VAC Max) Cabinet Size 18' & 21' DEFROST SPECIFICATIONS Cut-in 25 F -4 C Thermostat Cut-out 47 F 8 C Ohms CAUTION: All electrical parts and wiring must be shielded from torch flame. Do not allow torch to contact insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. A ', 15' & 17' 25 F -4 C 47 F 8 C Mechanical Timer - Defrost 30 Minutes Every 10 Hours of Compressor Run Time Electronic Timer (ADC) Defrost Up To 24 Minutes Every 6-72 Hours of Compressor Run Time CONDENSER FAN MOTOR RPM CW Opposite Shaft.15 Running SPECIFICATIONS NOTE: This product comes equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds. E lectrical VAC (127 VAC Max) 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) 165 Wire CONNECTOR PLUG CONNECTIONS Number 1 Green/Yellow 2 Yellow 3 Black 4 Lt. Blue W ire Color Connects to: Ground Water Valve Line Neutral LINE GRN / YEL P-3 P-1 THERMAL CUT-OUT GRN / YEL MOLD BRN MOUNTING PLATE MOTOR RED POWER MOLD HEATER 165 WATTS HOLD SWITCH C NC NO YEL THERMOSTAT C RED NO NC WATER FILL SWITCH BLU C NO NC SHUT-OFF SWITCH LT. BLU YEL RED NEUTRAL YEL P-4 P-2 WATER VALVE

23 Pictorial Schematic Ladder Schematic A - 8 NOTE: COMPRESSOR WIRING Induction Run Compressor with Relay 15 & 17 CUBIC FOOT 18 CUBIC FOOT 21 CUBIC FOOT SERVICE PARTS STATIC DYNAMIC E-STAR STATIC DYNAMIC E-STAR DYNAMIC E-STAR Compressor / Kit * Starter/PTC/TSD * N/A N/A N/A Run Capacitor * N/A N/A N/A Relay N/A N/A N/A N/A N/A Overload N/A N/A N/A N/A N/A Control Timer (if applicable) ADC (if applicable) N/A N/A N/A N/A N/A N/A N/A N/A Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor N/A N/A * Typical compressor kit includes compressor, electrical components, and filter-drier

24 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING SERVICE DATA SHEET INFORMATION Capacitor Run or Induction Run 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 25 to 35% 45 to 55% Freezer Refrigerature 2 to 8 F -17 to -13 C 35 to 40 F 2 to 4 C 0 to 5 F -18 to -15 C 35 to 40 F 2 to 4 C STANDARD - AUTOMATIC DEFROST TOP FREEZER MODELS (R134a) IMPORTANT SAFETY NOTICE P/N: Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until Holding Switch circuit is completed. All components of ice maker should function to complete the cycle. L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 110 to 120 psig 758 to 827 kpa 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 150 to 175 psig 1034 to 1207 kpa (Last 1/3 of cycle) 140 to to 185 (Running) 1.1 to to 1. 6 B ase Voltage VAC (127 VAC Max) VAC (127 VAC Max) Cabinet Size 18' & 21' DEFROST SPECIFICATIONS Cut-in 25 F -4 C Thermostat Cut-out 47 F 8 C Ohms The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing. IMPORTANT If any green grounding wires are moved during servicing, they must be returned to their original position and properly secured. CAUTION: All electrical parts and wiring must be shielded from torch flame. Do not allow torch to contact insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 95 to 105cc (3.2 to 3.6 oz.). When a water valve is replaced, the fill volume must be checked. A ', 15' & 17' 25 F -4 C 47 F 8 C Mechanical Timer - Defrost 30 Minutes Every 10 Hours of Compressor Run Time Electronic Timer (ADC) Defrost Up To 24 Minutes Every 6-72 Hours of Compressor Run Time CONDENSER FAN MOTOR RPM NOTE: Some products come equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds CW Opposite Shaft.15 Running LINE POWER NEUTRAL Wire CONNECTOR PLUG CONNECTIONS Number SPECIFICATIONS E lectrical VAC (127 VAC Max) 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) Green/Yellow 2 Yellow 3 Black 4 Lt. Blue W ire Color Connects to: Ground Water Valve Line Neutral GRN / YEL P-3 P-1 THER MAL CUT-OUT GRN / YEL MOLD BRN MOUN TING PLATE MOTOR RED MOLD HEATER HOLD SW ITCH YEL T HERMOSTAT WATER FILL SWITCH BLU SHUT-OF F SWITCH LT. B LU YEL RED YEL P-4 LT. BLU P-2 WATER VALVE

25 Pictorial Schematic Ladder Schematic A - 10 NOTE: DENOTES NOT ON ALL MODELS COMPRESSOR WIRING Induction Run Compressor with Relay 15 & 17 CUBIC FOOT 18 CUBIC FOOT 21 CUBIC FOOT SERVICE PARTS STATIC DYNAMIC E-STAR STATIC DYNAMIC E-STAR DYNAMIC E-STAR Compressor / Kit * Starter/PTC/TSD * N/A N/A N/A Run Capacitor * N/A N/A N/A Relay N/A N/A N/A N/A N/A Overload N/A N/A N/A N/A N/A Control Timer (if applicable) ADC (if applicable) N/A N/A N/A N/A N/A N/A N/A N/A Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor N/A N/A * Typical compressor kit includes compressor, electrical components, and filter-drier

26 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING SERVICE DATA SHEET INFORMATION Capacitor Run or Induction Run 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 25 to 35% 45 to 55% Freezer Refrigerature 2 to 8 F -17 to -13 C 35 to 40 F 2 to 4 C 0 to 5 F -18 to -15 C 35 to 40 F 2 to 4 C STANDARD - AUTOMATIC DEFROST TOP FREEZER MODELS (R134a) IMPORTANT SAFETY NOTICE P/N: Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until Holding Switch circuit is completed. All components of ice maker should function to complete the cycle. L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 110 to 120 psig 758 to 827 kpa 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 150 to 175 psig 1034 to 1207 kpa (Last 1/3 of cycle) 140 to to 185 (Running) 1.1 to to 1. 6 B ase Voltage VAC (127 VAC Max) VAC (127 VAC Max) Cabinet Size 18' & 21' DEFROST SPECIFICATIONS Cut-in 25 F -4 C Thermostat Cut-out 47 F 8 C Ohms The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing. IMPORTANT If any green grounding wires are moved during servicing, they must be returned to their original position and properly secured. CAUTION: All electrical parts and wiring must be shielded from torch flame. Do not allow torch to contact insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 95 to 105cc (3.2 to 3.6 oz.). When a water valve is replaced, the fill volume must be checked. A ', 15' & 17' 25 F -4 C 47 F 8 C Mechanical Timer - Defrost 30 Minutes Every 10 Hours of Compressor Run Time Electronic Timer (ADC) Defrost Up To 24 Minutes Every 6-72 Hours of Compressor Run Time CONDENSER FAN MOTOR RPM NOTE: Some products come equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds CW Opposite Shaft.15 Running LINE POWER NEUTRAL Wire CONNECTOR PLUG CONNECTIONS Number SPECIFICATIONS E lectrical VAC (127 VAC Max) 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) Green/Yellow 2 Yellow 3 Black 4 Lt. Blue W ire Color Connects to: Ground Water Valve Line Neutral GRN / YEL P-3 P-1 THER MAL CUT-OUT GRN / YEL MOLD BRN MOUN TING PLATE MOTOR RED MOLD HEATER HOLD SW ITCH YEL T HERMOSTAT WATER FILL SWITCH BLU SHUT-OF F SWITCH LT. B LU YEL RED YEL P-4 LT. BLU P-2 WATER VALVE

27 Pictorial Schematic Ladder Schematic A - 12 NOTE: DENOTES NOT ON ALL MODELS COMPRESSOR WIRING Induction Run Compressor with Relay 15 & 17 CUBIC FOOT 18 CUBIC FOOT 21 CUBIC FOOT SERVICE PARTS STATIC DYNAMIC E-STAR STATIC DYNAMIC E-STAR DYNAMIC E-STAR Compressor / Kit * Starter/PTC/TSD * N/A N/A N/A N/A N/A Run Capacitor * N/A N/A N/A N/A N/A Relay N/A N/A N/A Overload N/A N/A N/A Control Timer (if applicable) ADC (if applicable) N/A N/A N/A N/A N/A N/A N/A N/A Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor N/A N/A * Typical compressor kit includes compressor, electrical components, and filter-drier

28 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING Capacitor Run or Induction Run 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 25 to 35% 45 to 55% Freezer Refrigerature 2 to 8 F -17 to -13 C 35 to 40 F 2 to 4 C 0 to 5 F -18 to -15 C 35 to 40 F 2 to 4 C STANDARD - AUTOMATIC DEFROST TOP FREEZER MODELS (R134a) SERVICE DATA SHEET IMPORTANT SAFETY NOTICE P/N: INFORMATION Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until Holding Switch circuit is completed. All components of ice maker should function to complete the cycle. L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 110 to 120 psig 758 to 827 kpa 8 to 16 psig 55 to 110 kpa 1 to 4 psig 7 to 28 kpa 150 to 175 psig 1034 to 1207 kpa (Last 1/3 of cycle) 140 to to 185 (Running) 1.1 to to 1. 6 B ase Voltage VAC (127 VAC Max) VAC (127 VAC Max) Cabinet Size 18' & 21' DEFROST SPECIFICATIONS Cut-in 25 F -4 C Thermostat Cut-out 47 F 8 C Ohms The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing. IMPORTANT If any green grounding wires are moved during servicing, they must be returned to their original position and properly secured. CAUTION: All electrical parts and wiring must be shielded from torch flame. Do not allow torch to contact insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 95 to 105cc (3.2 to 3.6 oz.). When a water valve is replaced, the fill volume must be checked. A ', 15' & 17' 25 F -4 C 47 F 8 C Mechanical Timer - Defrost 30 Minutes Every 10 Hours of Compressor Run Time Electronic Timer (ADC) Defrost Up To 24 Minutes Every 6-72 Hours of Compressor Run Time CONDENSER FAN MOTOR RPM NOTE: Some products come equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds CW Opposite Shaft.15 Running LINE POWER NEUTRAL Wire CONNECTOR PLUG CONNECTIONS Number SPECIFICATIONS E lectrical VAC (127 VAC Max) 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) Green/Yellow 2 Yellow 3 Black 4 Lt. Blue W ire Color Connects to: Ground Water Valve Line Neutral GRN / YEL P-3 P-1 THER MAL CUT-OUT GRN / YEL MOLD BRN MOUN TING PLATE MOTOR RED MOLD HEATER HOLD SW ITCH YEL T HERMOSTAT WATER FILL SWITCH BLU SHUT-OF F SWITCH LT. B LU YEL RED YEL P-4 LT. BLU P-2 WATER VALVE

29 A & 17 CUBIC FOOT 18 CUBIC FOOT 21 CUBIC FOOT SERVICE PARTS STATIC DYNAMIC E-STAR STATIC DYNAMIC E-STAR DYNAMIC E-STAR Compressor / Kit * Starter/PTC/TSD * N/A N/A N/A N/A N/A Run Capacitor * N/A N/A N/A N/A N/A Relay N/A N/A N/A Overload N/A N/A N/A Control Timer (if applicable) ADC (if applicable) N/A N/A N/A N/A N/A N/A N/A N/A Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor N/A N/A Induction Run Compressor with Relay COMPRESSOR WIRING * Typical compressor kit includes compressor, electrical components, and filter-drier

30 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING Type A With Run/Start Capacitor 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 32 to 40% 55 to 65% Freezer Refrigerator L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 0 to 4 F -18 to -16 C 34 to 39 F 1 to 4 C 5 to 12 psig 34 to 83 kpa -2 to 2 psig -14 to 14 kpa 90 to psig 621 to 793 kpa -1 to 3 F -18 to -16 C 34 to 39 F 1 to 4 C 5 to 12 psig 34 to 83 kpa -2 to 2 psig -14 to 14 kpa 130 to 155 psig 896 to 1069 kpa (Last 1/3 of cycle) 120 to to 160 (Running) 1.2 to to 1. 5 B ase Voltage vac (127 vac max) vac (127 vac max) SERVICE DATA SHEET R134a ICE & WATER - AUTOMATIC DEFROST SIDE BY SIDE MODELS IMPORTANT SAFETY NOTICE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing. IMPORTANT If any green grounding wires are moved during servicing, they must be returned to their original position and properly secured. INFORMATION Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until holding switch circuit is completed. All components of ice maker should function to complete the cycle. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 102 to 130cc (3.4 to 4.3 oz.). When a water valve is replaced, the fill volume must be checked. Cabinet Size DEFROST SPECIFICATIONS Cut-in 23' & 26' 25 F -4 C Thermostat Cut-out 47 F 8 C Ohms Electronic Timer - (ADC) Defrost 24 minutes every 6 to 72 hours of compressor run time. CAUTION: All electrical parts and wiring must be shielded from torch flame. Do not allow torch to contact insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. A - 15 CONDENSER FAN MOTOR RPM CW Opposite Shaft.1 Running SPECIFICATIONS E lectrical vac (127 vac max) 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) NOTE: This product comes equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds. 165 P-3 Wire CONNECTOR PLUG CONNECTIONS Number W ire Color Connects to: P-4 1 Green/Yellow 2 Yellow 3 Black Ground Water Valve Line GREEN/YELLOW GREEN/YELLOW P-1 P-2 4 Lt. Blue Neutral

31 A CUBIC FOOT 26 CUBIC FOOT SERVICE PARTS STANDARD E-STAR STANDARD E-STAR Compressor Kit * Starter/PTC * Run Capacitor * Temp. Control-Refr Temp. Control-Frzr Timer (if applicable) N/A N/A N/A N/A ADC (if applicable) Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor * Typical compressor kit includes compressor, electrical components, and filter-drier

32 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING Type A With Run/Start Capacitor 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 32 to 40% 55 to 65% Freezer Refrigerator L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 0 to 4 F -18 to -16 C 34 to 39 F 1 to 4 C 5 to 12 psig 34 to 83 kpa -2 to 2 psig -14 to 14 kpa 90 to psig 621 to 793 kpa -1 to 3 F -18 to -16 C 34 to 39 F 1 to 4 C 5 to 12 psig 34 to 83 kpa -2 to 2 psig -14 to 14 kpa 130 to 155 psig 896 to 1069 kpa (Last 1/3 of cycle) 120 to to 160 (Running) 1.2 to to 1. 5 B ase Voltage vac (127 vac max) vac (127 vac max) SERVICE DATA SHEET R134a ICE & WATER - AUTOMATIC DEFROST SIDE BY SIDE MODELS IMPORTANT SAFETY NOTICE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing. IMPORTANT If any green grounding wires are moved during servicing, they must be returned to their original position and properly secured. INFORMATION Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until holding switch circuit is completed. All components of ice maker should function to complete the cycle. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 102 to 130cc (3.4 to 4.3 oz.). When a water valve is replaced, the fill volume must be checked. Cabinet Size DEFROST SPECIFICATIONS Cut-in 23' & 26' 25 F -4 C Thermostat Cut-out 47 F 8 C Ohms Electronic Timer - (ADC) Defrost 24 minutes every 6 to 72 hours of compressor run time. CAUTION: All electrical parts and wiring must be shielded from torch flame. Do not allow torch to contact insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. A - 17 CONDENSER FAN MOTOR RPM CW Opposite Shaft.1 Running SPECIFICATIONS E lectrical vac (127 vac max) 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) NOTE: This product comes equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds. 165 P-3 Wire CONNECTOR PLUG CONNECTIONS Number W ire Color Connects to: P-4 1 Green/Yellow 2 Yellow 3 Black Ground Water Valve Line GREEN/YELLOW GREEN/YELLOW P-1 P-2 4 Lt. Blue Neutral

33 A CUBIC FOOT 26 CUBIC FOOT SERVICE PARTS STANDARD E-STAR STANDARD E-STAR Compressor Kit * Starter/PTC/TSD * Run Capacitor * Temp. Control-Refr Temp. Control-Frzr Timer (if applicable) N/A N/A N/A N/A ADC (if applicable) Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor * Typical compressor kit includes compressor, electrical components, and filter-drier

34 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING Type A With Run/Start Capacitor 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 32 to 40% 55 to 65% Freezer Refrigerator L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 0 to 4 F -18 to -16 C 34 to 39 F 1 to 4 C 5 to 12 psig 34 to 83 kpa -2 to 2 psig -14 to 14 kpa 90 to psig 621 to 793 kpa -1 to 3 F -18 to -16 C 34 to 39 F 1 to 4 C 5 to 12 psig 34 to 83 kpa -2 to 2 psig -14 to 14 kpa 130 to 155 psig 896 to 1069 kpa (Last 1/3 of cycle) 120 to to 160 (Running) 1.2 to to 1. 5 B ase Voltage vac (127 vac max) vac (127 vac max) Cabinet Size DEFROST SPECIFICATIONS Cut-in 23' & 26' 25 F -4 C Thermostat Cut-out 47 F 8 C Ohms Electronic Timer - (ADC) Defrost 24 minutes every 6 to 72 hours of compressor run time. SERVICE DATA SHEET R134a ICE & WATER - AUTOMATIC DEFROST SIDE BY SIDE MODELS IMPORTANT SAFETY NOTICE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing. IMPORTANT If any green grounding wires are moved during servicing, they must be returned to their original position and properly secured. CAUTION: All electrical parts and wiring must be shielded from torch flame. Do not allow torch to contact insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. NOTE: This product comes equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds. INFORMATION Test Cycling Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use screwdriver to rotate motor gear counterclockwise until holding switch circuit is completed. All components of ice maker should function to complete the cycle. Water Fill Volume The water fill adjustment screw will change the fill time. One full turn is equal to 20cc (.68 oz.). The correct fill is 102 to 130cc (3.4 to 4.3 oz.). When a water valve is replaced, the fill volume must be checked. A - 19 CONDENSER FAN MOTOR RPM CW Opposite Shaft.1 Running SPECIFICATIONS P-3 E lectrical vac (127 vac max) 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) 165 P-4 CONNECTOR PLUG CONNECTIONS Wire Number 1 Green/Yellow 2 Yellow W ire Color Connects to: Ground Water Valve GREEN/YELLOW GREEN/YELLOW P-1 P-2 3 Black 4 Lt. Blue Line Neutral

35 A CUBIC FOOT 26 CUBIC FOOT SERVICE PARTS STANDARD E-STAR STANDARD E-STAR Compressor Kit * Starter/PTC/TSD * Run Capacitor * Temp. Control-Refr Temp. Control-Frzr Timer (if applicable) N/A N/A N/A N/A ADC (if applicable) Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor * Typical compressor kit includes compressor, electrical components, and filter-drier

36 PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING Type A With Run/Start Capacitor 65 F (18 C) Ambient 90 F (32 C) Ambient O perating Time 32 to 40% 55 to 65% Freezer Refrigerator L ow Side Pressure ( cut-in) L ow Side Pressure ( cut-out) H igh Side Pressure ( Last 1/3 of cycle) 0 to 4 F -18 to -16 C 34 to 39 F 1 to 4 C 5 to 12 psig 34 to 83 kpa -2 to 2 psig -14 to 14 kpa 90 to psig 621 to 793 kpa -1 to 3 F -18 to -16 C 34 to 39 F 1 to 4 C 5 to 12 psig 34 to 83 kpa -2 to 2 psig -14 to 14 kpa 130 to 155 psig 896 to 1069 kpa (Last 1/3 of cycle) 120 to to 160 (Running) 1.2 to to 1. 5 B ase Voltage vac (127 vac max) vac (127 vac max) Cabinet Size DEFROST SPECIFICATIONS Cut-in Thermostat Cut-out Ohms SERVICE DATA SHEET R134a ICE & WATER - AUTOMATIC DEFROST SIDE BY SIDE MODELS IMPORTANT SAFETY NOTE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance. IMPORTANT If any green grounding wires are removed during servicing, they must be returned to their original position and properly secured. INFORMATION Test Cycling Press the momemtary contact on the ON/OFF switch for approximately 15 seconds. Ice maker will continue to complete the cycle. Water Fill Volume Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. The water fill adjustment screw will change the fill time. One turn is equal to 20cc (.68 oz.). The correct fill is 102 to 110cc (3.25 to 3.5 oz.). When a water valve is replaced, the fill volume must be checked Motor Gear Water Fill Adjustment TURN Mounting Plate Screws Ice Maker ON/OFF Switch A ' & 26' 25 F -4 C 47 F 8 C Electronic Timer - (ADC) Defrost 24 minutes every 6 to 72 hours of compressor run time. CONDENSER FAN MOTOR RPM CW Opposite Shaft.1 Running SPECIFICATIONS CAUTION All electrical parts and wiring must be shielded from torch flame. DO NOT allow torch to touch insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. Mounting Plate Screw Timing Gear E lectrical vac (127 vac max) 60 Hertz T hermostat O pens at 48 F (9 C) Closes at 15 F (-9 C) 165 Wire CONNECTOR PLUG CONNECTIONS Number 1 Green/Yellow 2 Yellow 3 Black 4 Lt. Blue W ire Color Connects to: Ground Water Valve Line Neutral NOTE This product comes equipped with an Electronic Defrost Control. To initiate defrost, depress the fresh food light switch 5 times in 6 seconds (light bulb must be working). To terminate defrost, depress the fresh food light switch 5 times in 6 seconds.

37 A CUBIC FOOT 26 CUBIC FOOT SERVICE PARTS STANDARD E-STAR STANDARD E-STAR Compressor Kit * Starter/PTC/TSD * Run Capacitor * Temp. Control-Refr Temp. Control-Frzr Timer (if applicable) N/A N/A N/A N/A ADC (if applicable) Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor * Typical compressor kit includes compressor, electrical components, and filter-drier

38 SERVICE DATA SHEET INFORMATION Test Cycling PERFORMANCE DATA NO LOAD AND NO DOOR OPENINGS AT MID-POINT CONTROL SETTING Type A with Run/Start Capacitor IMPORTANT 65 F (18 C) Ambient 90 F (32 C) Ambient Variable Speed Standard Variable Speed Standard Operating Time 74 to 84% 32 to 40% 100% 55 to 65% Freezer Refrigerator Low Side Pressure (cut-in) Low Side Pressure (cut-out) High Side Pressure (last 1/3 cycle) -2 to 2 F -19 to -17 C 34 to 39 F 1 to 4 C 5 to 12 psig 43 to 83 kpa -2 to 2 psig -14 to 14kPa 90 to 105 psig 621 to 724 kpa 0 to 4 F -18 to -16 C 34 to 39 F 1 to 4 C 5 to 12 psig 43 to 83 kpa -2 to 2 psig -14 to 14kPa 90 to psig 621 to 793 kpa -1 to 3 F -18 to -16 C 34 to 39 F 1 to 4 C Please return this sheet to its original location. N/A -2 to 2 psig -14 to 14kPa 120 to 135 psig 827 to 931 kpa -1 to 3 F -18 to -16 C 34 to 39 F 1 to 4 C 5 to 12 psig 43 to 83 kpa -2 to 2 psig -14 to 14kPa 130 to 155 psig 896 to 1069 kpa (last 1/3 cycle) 60 to to to to 160 (running).7 to to to to 1.5 Base Voltage vac (127 vac max) vac (127 vac max) DEFROST SPECIFICATIONS Cabinet Size Thermostat Cut-in Cut-out Ohms F (-4 C) 47 F (8 C) Electronic Timer (ADC) Defrost 24 minutes every 6 96 hours of compressor run time. Electrical CONDENSER FAN MOTOR RPM CW Opposite Shaft.1 Running SPECIFICATIONS vac (127 vac max) Thermostat Opens at 48 F (9 C) Closes at 15 F (-9 C) Voltage 85 vac CONNECTOR PLUG CONNECTIONS Wire Number Wire Color Connects to: 1 Green/Yellow Ground 2 Yellow Water Valve 3 Black Line 4 Light Blue Neutral ICE & WATER - AUTOMATIC DEFROST COUNTER DEPTH SIDE BY SIDE - R134a IMPORTANT SAFETY NOTE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance. IMPORTANT If any green grounding wires are removed during servicing, they must be returned to their original position and properly secured. CAUTION All electrical parts and wiring must be shielded from torch flame. DO NOT allow torch to touch insulation; it will char at 200 F and flash ignite (burn) at 500 F. Excessive heat will distort the plastic liner. NOTE This product comes equipped with an Adaptive Defrost Control (ADC). To activate manual defrost, press and hold the Freezer temperature UP (WARMER) key while pressing the Fresh Food temperature DOWN (COLDER) key 5 times within 6 seconds. A d in the freezer temperature window and F in the refrigerator temperature window will display when the heater is activated. To deactivate manual defrost, press and hold Freezer temperature UP (WARMER) key while pressing the Fresh Food temperature DOWN (COLDER) key 5 times within 6 seconds. d and F will be displayed until the defrost cycle is complete. (approx. 8 minutes) Press the momemtary contact on the ON/OFF switch for approximately 15 seconds. Ice maker will continue to complete the cycle. Water Fill Volume Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. The water fill adjustment screw will change the fill time. One turn is equal to 20cc (.68 oz.). The correct fill is 102 to Motor Gear Water Fill Adjustment Mounting Plate Screw 110cc (3.25 to 3.5 oz.). When a water valve is replaced, the fill volume must be checked TURN Mounting Plate Screws Timing Gear Ice Maker ON/OFF Switch A - 23

39 1 2 1 VAC 2TO5VDC 2 VARIABLE SPEED COMPRESSOR FOR E-STAR Variable Speed Compressor and E-Star only A - 24 SERVICE PARTS 23 CUBIC FOOT STANDARD 1 E-STAR 2 Compressor Kit * Power Board (Sigma Main) N/A Inverter N/A Starter/PTC N/A Run Capacitor N/A Sensor, Damper Assembly Defrost Kit Defrost Thermostat Kit Evaporator Fan Motor Condenser Fan Motor * Typical Compressor Kit includes compressor, electrical components and filter-drier.