Grant Product Guide. A complete guide to Grant high efficiency technologies. 1st August (0) w w w.grantuk.com

Transcription

1 Grant Product Guide A complete guide to Grant high efficiency technologies st August 07 This supersedes all previous issues +44 (0) w w w.grantuk.com

2 Contents Oil Fired Boilers & Flues 4-3 Vortex Eco Range - utility & external (outdoor modules) 4 Vortex Pro Range - utility & external (outdoor modules) 5 Vortex Pro Range - combi models 6 Vortex Range - boiler house models 6 VortexBlue Range - utility, external & combi models 7 EZ-Fit Flue systems 8-3 Air Source Heat Pumps 4-5 Aerona 3 air to water heat pumps 4-5 Oil boiler/heat Pump Hybrid 6-7 Grant VortexAir Hybrid 6-7 Cylinders & Thermal Stores 8-5 MonoWave heat pump cylinders 8-9 DuoWave heat pump cylinders 8-9 DuoWave solar cylinders 0- DuoWave Plus cylinders ThermaWave thermal stores 3-5 Solar Thermal Systems 6-3 On roof kits 8 In roof kits 9-30 Flat roof kits 30 Accessories 3 Biomass Boilers & Accessories 3-46 Vecta wood pellet boiler range - internal model 3-33 Vecta wood pellet boiler range - external model Vecta wood pellet boiler range - internal side pellet store 36 Vecta wood pellet boiler range - external side pellet store 37 Spira wood pellet boiler range - internal models 38-4 SpiraPod Range 4 SpiraVac vacuum systems 43 Biomass flues Wood pellet stores 46 Magnetic Central Heating Filter 47 MagOne filter 47 Energy Management Controls 48-5 Controllers 48 Low loss headers Zone pump kits 5

3 +44 (0) w w w.grantuk.com 3

4 Oil Fired Boilers Grant Vortex Eco Range Stainless steel condensing heat exchanger SAP 009 seasonal efficiencies of 90.3% - 9.6% Multidirectional flue options Simplified casing, control and pipework arrangement Product Output Dimensions Weight Code Btu/h kw H W D (KG) Burner Internal standard models - white cased VTXECO5/ RDB. VTXECO/ RDB. VTXECO6/ RDB. Internal sealed system models - white cased VTXSECO5/ RDB. VTXSECO/ RDB. VTXSECO6/ RDB. External standard modules (inc flue) - powder coated case VTXOMECO5/ RDB. VTXOMECO/ RDB. VTXOMECO6/ RDB. External sealed system models (inc flue) - powder coated cased VTXSOMECO5/ RDB. VTXSOMECO/ RDB. VTXSOMECO6/ RDB. Wall hung internal standard models - white cased VTXWH/ MAX VTXWH6/ MAX Wall hung internal sealed system models - white cased VTXSWH/ MAX VTXSWH6/ MAX Wall hung external standard models (inc flue) - powder coated cased VTXOMWH/ MAX VTXOMWH6/ MAX Wall hung external sealed system models (inc flue) - powder coated cased VTXSOMWH/ MAX VTXSOMWH6/ MAX 4

5 Grant Vortex Pro Range Award winning range Stainless steel condensing heat exchanger SAP 009 seasonal efficiencies of 90.7% % Multidirectional flue options Riello burner technology Oil Fired Boilers Product Output Dimensions Weight Code Btu/h kw H W D (KG) Burner Internal standard models - white cased VTX5/ RDB. VTX5/ RDB VTX6/ RDB VTX36/ RDB. VTX46/ RDB3. VTX58/ RDB3. Internal sealed system models - white cased VTXS5/ RDB VTXS6/ RDB VTXS36/ RDB. External standard modules (inc flue) - powder coated case VTXOM5/ RDB. VTXOM5/ RDB VTXOM6/ RDB VTXOM36/ RDB. VTXOM46/ RDB3. VTXOM58/ RDB3. Accessories & Control Options VTXOMSSKIT VTXOMSSKIT6 VTXOMSSKIT46 Description 0 Litre Sealed System Kit for VTXOM5 Litre Sealed System Kit for VTXOM56 6 Litre Sealed System Kit for VTXOM636/ VTXOM3646 5

6 Oil Fired Boilers Grant Vortex Pro Combi Range Award winning range Stainless steel condensing heat exchanger SAP 009 seasonal efficiencies of % Multidirectional flue options Riello burner technology Product Output Dimensions Weight Code Btu/h kw H W D (KG) Burner Internal Combi models - white cased VTXCOMBI RDB. VTXCOMBI RDB VTXCOMBI RDB. Internal Combi XS model - white cased VTXXSCOMBI RDB. External Combi modules (incl flue) - powder coated cased VTXOMCOMBI RDB. VTXOMCOMBI RDB VTXOMCOMBI RDB. Grant Vortex Boiler House Range New distinctive red powder coated finish Stainless steel condensing heat exchanger SAP 009 seasonal efficiencies of 90.7% % Ideal for difficult to access locations Multidirectional flue options Externally mounted Riello RDB burner Product Output Dimensions Weight Code Btu/h kw H W D (KG) Burner Internal boiler house models - red cased VTXBH RDB. VTXBH RDB. VTXBH RDB. VTXBH RDB. VTXBH RDB3. VTXBH RDB3. 6

7 Grant VortexBlue Range Market leading Riello Blue Flame burner Gross SAP 009 seasonal ef ficiencies of 89.5% % Burner NOx emissions below 08 European limit of 0mg/kWh Neon diagnostic indicators Oil Fired Boilers Product Code Output Btu/h kw H Dimensions W D Weight (KG) Internal standard models - white cased VTXBF VTXBF VTXBF Internal sealed system models - white cased VTXSBF VTXSBF VTXSBF Internal combi modules - white cased Burner Riello RDB BLU Riello RDB BLU Riello RDB BLU Riello RDB BLU Riello RDB BLU Riello RDB BLU VTXBFCOM Riello RDB BLU VTXBFCOM Riello RDB BLU VTXBFCOM Riello RDB BLU External modules (incl flue) - powder coated case VTXBFOM Riello RDB BLU VTXBFOM Riello RDB BLU VTXBFOM Riello RDB BLU External combi modules (incl flue) - powder coated cased VTXBFOMCOM Riello RDB BLU VTXBFOMCOM Riello RDB BLU VTXBFOMCOM Riello RDB BLU 7

8 EZ-Fit Flues Yellow System Low level balanced flue kits Low level Stainless steel Balanced Suitable for all internal Vortex models Terminal section and guard are black painted Plume diverter kits available Output (kw) Description EZ90B -6 EZ90SB -6 X90S -6 Extension 5mm X90M -6 Extension 450mm X90L -6 Extension 675mm EZELB90-6 EZ45/90-6 Standard flue kit Walls up to 450mm Includes s/s terminal guard (Black painted finish) Short flue kit Single skin walls up to 30mm Includes s/s terminal guard (Black painted finish) 90 Elbow Kit (Includes 90 elbow and 5mm Extension) 45 Elbow Kit (Includes 45 elbow and 5mm Extension) EZ45/90S -6 Short elbow only up to 6kW gpda90b -6 Adjustable plume diverter kit 80mm x metres (Black painted finish) GPD50EXT/90B -6 Extension 50mm (Black painted finish) GPD500EXT/90B -6 Extension 500mm (Black painted finish) GPD000EXT/90B -6 Extension 000mm (Black painted finish) GPDA45/90B elbow (Black painted finish) GPDBRKT90B -6 Wall bracket (Black painted finish) EZ00B 6-70 EZ00SB 6-70 X00s 6-70 Extension 5mm X00m 6-70 Extension 450mm X00l 6-70 Extension 675mm EZELB EZ45/ Standard flue kit Walls up to 450mm Includes s/s terminal guard (Black painted finish) Short flue kit Single skin walls up to 30mm Includes s/s terminal guard (Black painted finish) 90 Elbow Kit (Includes 90 elbow and 5mm Extension) 45 Elbow Kit (Includes 45 elbow and 5mm Extension) EZ45/00S 6-70 Short elbow only above 6kW gpda00b 6-70 Adjustable plume diverter kit 00mm x metres (Black painted finish) GPD50EXT/00B 6-70 Extension 50mm (Black painted finish) GPD500EXT/00B 6-70 Extension 500mm (Black painted finish) GPD000EXT/00B 6-70 Extension 000mm (Black painted finish) GPDA45/00B elbow (Black painted finish) GPDBRKT00B 6-70 Wall bracket (Black painted finish) 8

9 White System High level/ vertical balanced flue kits High level/ Vertical Suitable for all internal Vortex models Stainless steel white powder coated Easy to install Balanced EZ-Fit Flues Output (kw) Description HlK metre High level adjustable flue kit c/w 90 elbow and terminal vtk Adjustable Vertical 3 metre flue kit c/w terminal and storm collar extk35/90-6 Extension 5mm (9 ) extk09450/90-6 Extension 450mm (8 ) extk950/90-6 Extension 950mm (38 ) extk3adj/90-6 Adjustable extension mm (0 to 8 ) elbk45/ elbow VTMF90/00-70 Pitched master flashing [aluminium] VTk5P90-6 Pitched flashing [lead] VTk7F90-6 Flat flashing BRk990-6 Wall bracket [galvanised] vttext90-6 Black extension for vertical terminal 80mm x mtr HlK metre High level adjustable flue kit c/w 90 elbow and terminal VTK Adjustable Vertical 3 metre flue kit c/w terminal and storm collar extk35/ Extension 5mm (9 ) extk0450/ Extension 450mm (8 ) extk950/ Extension 950mm (38 ) extk4adj/ Adjustable extension mm (0 to 8 ) ELBk45/ elbow VTMF90/00-70 Pitched master flashing [aluminium] VTk6P Pitched flashing [lead] VTK6P00X 6-70 Pitched flashing [lead replacement, incl collar] VTk 8F Flat flashing BRk Wall bracket [galvanised] vttext Black extension for vertical terminal 00mm x mtr NOTE: High level/vertical flues, extensions and accessories can be used with all internal boilers. Vertical flue kits can be extended to a maximum straight length of metres. Deduct metre for each 45 elbow (max 6 elbows). High level flue kits can be extended to a maximum length of 0 metres. Deduct metre for each 45 elbow (max 6 elbows). For information on Plume Diverter Kits for high level flues, please contact our Technical Department 9

10 EZ-Fit Flues Green System External High Level/ Vertical balanced flue kits High level/ Vertical Stainless steel Balanced Twin wall insulated vertical extensions Suitable for all internal and external Vortex models Black painted Output (kw) Description GK90-6 Standard Starter Kit (Stainless Steel) GK90S -6 Short Starter Kit (Stainless Steel) GKM90-6 Outdoor Module Starter (Elbow) + Test point GKM90C -6 Outdoor Module Starter (Straight) + Test point GX50/90-6 Extension 50mm GX50/90-6 Extension 50mm GX450/90-6 Extension 450mm GX950/90-6 Extension 950mm GXA50/90-6 Adjustable Extension 95-70mm GE45/ Elbow GTL90-6 Straight Terminal Only GTH90-6 High level 90 Terminal GTV90-6 Vertical Terminal GWB90-6 Wall Bracket GEB90-6 Extended Wall Bracket GK * Standard Starter Kit (Stainless Steel) GK00S 6-70* Short Starter Kit (Stainless Steel) GKM * Outdoor Module Starter (Elbow) + Test point GKM00C 6-46* Outdoor Module Starter (Straight) + Test point GX50/ * Extension 50mm GX50/ * Extension 50mm GX450/ * Extension 450mm GX950/ * Extension 950mm GXA50/ * Adjustable Extension 95-70mm GE45/ * 45 Elbow GTL * Straight Terminal Only GTH * High level 90 Terminal GTV * Vertical Terminal GWB * Wall Bracket GEB * Extended Wall Bracket CFA5/70-70 CF Adaptor/Connector from Orange to Green System NOTE: *The Grant Eco Outdoor Modules VTXOMECO635 and VTXSOMECO6/35 use the smaller -6 flue pipe. Please use extensions from the Yellow System to extend starter kits horizontally. The CFA5/70 is to only be used with the Grant Green and Orange Flue System. Fitting with any other flue system could invalidate the warranty of the boiler. If the CFA5/70 is not sent with components of the Green or Orange Systems, then full installation details will be required prior to despatch. 0

11 Orange System Conventional flue kits Conventional flexi kits Smooth bore stainless steel liner White powder coated extensions Suitable for all internal Vortex models Available as complete kits EZ-Fit Flues Output (kw) Description GFKIT6/00-46 Flexi Kit 00mm dia x 6m GFKIT8/00-46 Flexi Kit 00mm dia x 8m GFKIT0/00-46 Flexi Kit 00mm dia x 0m GFKIT/00-46 Flexi Kit 00mm dia x m GFKIT/00-46 Flexi Kit 00mm dia x m GFKIT4/00-46 Flexi Kit 00mm dia x 4m GFKIT6/00-46 Flexi Kit 00mm dia x 6m WX50/00-46 White Extension 50mm x 00mm dia WX50/00-46 White Extension 50mm x 00mm dia WX450/00-46 White Extension 450mm x 00mm dia WX950/00-46 White Extension 950mm x 00mm dia WXA50/ mm x 300mm x ø00mm White Adjustable Extension WE45/00-46 White 45 Elbow x 00mm dia GFKIT6/ Flexi Kit 5mm dia x 6m GFKIT8/ Flexi Kit 5mm dia x 8m GFKIT0/ Flexi Kit 5mm dia x 0m GFKIT/ Flexi Kit 5mm dia x m GFKIT/ Flexi Kit 5mm dia x m GFKIT4/ Flexi Kit 5mm dia x 4m GFKIT6/ Flexi Kit 5mm dia x 6m WX50/ White Extension 50mm x 5mm dia WX50/ White Extension 50mm x 5mm dia WX450/ White Extension 450mm x 5mm dia WX950/ White Extension 950mm x 5mm dia WXA50/ mm x 300mm x ø5mm White Adustable Extension WE45/ White 45 Elbow x 5mm dia Flexi Kit includes: Terminal/top plate/flexi-flue adaptor assembly, adaptor to flexi, boiler flue connector, locking band and fixing screws, plus tube of silicon and length of smooth bore insulated flexible flue liner. NOTE: Maximum vertical height from top of the boiler to the terminal is 9 metres. Maximum of x 45 elbows can be used.

12 EZ-Fit Flues Red System Flexi Vertical balanced flue kits Balanced flexi kits Smooth bore stainless steel inner liner Stainless Steel outer liner Suitable for all internal Vortex models up to 6kW Available as complete kits Output (kw) Description gfxbf6/6comr -6 6m Balanced Flexi Liner Kit gfxbf8/6comr -6 8m Balanced Flexi Liner Kit gfxbf0/6comr -6 0m Balanced Flexi Liner Kit gfxbf/6comr -6 m Balanced Flexi Liner Kit EXTK35/90-6 Extension 5mm (9 ) EXTK09450/90-6 Extension 450mm (8 ) EXTK950/90-6 Extension 950mm (38 ) EXTK3ADJ/90-6 Adjustable extension mm (0 to 8 ) ELBK45/ elbow Liner Kit includes: 5mm flexi liner, 80mm 36 stainless steel smooth bore flexi liner, Boiler Connector, Telescopic Extension, Rigid to Flexi Adaptor and Terminal Assembly (approximate height above boiler case 80-0mm) NOTE: Maximum vertical height from top of the boiler to the terminal is 0mtrs. Deduct mtr for each 45 elbow (max 4 elbows). Ref Location of outlet (see diagram opposite) Pressure Jet (mm) Condensing (mm) A Directly below an opening, air brick opening, opening window, etc ** B Horizontally to an opening, air brick opening, opening window, etc ** C Below a gutter, eaves or balcony with protection 75 * 000 ** D Below a gutter, eaves or balcony without protection ** E From vertical sanitary pipe work 300 F From an internal or external corner 300 G Above ground or balcony level 300 H From a surface or boundary facing the terminal ** J From a terminal facing the terminal 00 K Vertically from a terminal on the same wall 500 L Horizontally from a terminal on the same wall 750 M Above the highest point of an intersection with the roof 600 N From a vertical structure to the side of the terminal 750 O Above a vertical structure less than 750 mm from the side of the terminal 600 P From a ridge terminal to a vertical structure on the roof 500 Q Above or to the side of any opening on a flat or sloping roof 300 R Below any opening on a sloping roof 000 S From oil storage tank (Class ) 800 *** Note: * A heat shield at least 750mm wide must be fitted to provide protection of combustible material ** Clearances required by BS 540-:04 to alleviate the ef fect of plume nuisance. If a risk assessment shows that there will be no impact from plumbing, then the 'pressure jet' figure could apply - seek confirmation from Local Authority Building Control. *** Seek guidance from OFTEC Book 3 (Oil Storange and Supply).

13 Clearances. Appliances burning class D fuel have additional restrictions. Refer to BS 540-:04.. Vertical structure in N, O and P includes tank or lift rooms, parapets, dormers, etc. 3. Terminating positions A to L are only permitted for appliances that have been approved for low level flue discharge when tested in accordance with BS EN 303-, OFS A00 or OFS A0. 4. Terminating positions should be at least.8 metres from an oil storage tank (Class ) unless a wall with at least 30 minutes fire resistance and extending 300 mm higher and wider than the tank is provided between the tank and the terminating position. 5. Where a flue is terminated less than 600 mm away from a projection above it and the projection consists of plastics or has a combustible or painted surface, then a heat shield of at least 750 mm wide should be fitted to protect these surfaces. 6. If the lowest part of the terminal is less than metres above the ground, balcony, flat roof or other place to which any person has access, the terminal should be protected by a guard. 7. Notwithstanding the dimensions given above, a terminal should not be sited closer than 300 mm to combustible material. In the case of a thatched roof, double this separation distance should be provided. It is also advisable to treat the thatch with a fire retardant material and close wire in the immediate vicinity of the flue. 8. A flue or chimney should not pass through the roof within the shaded area delineated by dimensions Q and R. 9. Where protection is provided for plastics components, such as guttering, this should be to the standard specified by the manufacturer of the plastics components. 0. Terminals must not be sited under car ports.. Terminals at low levels (terminals under. metres) have more restrictive recommendations and should not be positioned near public footways, frequently used access routes, car parking spaces less than.5 metres from the terminal or patio's (hard surface area). Further guidance can be obtained from BS 540-:04, OFTEC Book 4 (Installation) and Approved Document J. Grant UK flue products are fully compliant with the CE (Communauté Européenne/European Community) standards having undergone rigorous product testing. EZ-Fit Flues 3

14 Air Source Heat Pumps Aerona 3 ASHP Range Air to water Inverter driven MCS approved Single phase Compact size Base tray heating element Simple plumbing and electrical connections HPID6 HPID0 HPID6 4

15 Aerona 3 ASHP Range Grant Aerona 3 Heat Pumps Model HPID6 HPID0 HPID6 Heating A++ A++ A++ ErP Rating Hot Water* A A A Height (mm) Width (mm) Depth (mm) Empty Weight (kg) Full Capacity (kw) Power input (kw) Running current (Max) (A) ** 6.4 (.) 0. (7.5) 7.0 (5.3) COP (at 7 o C air/ 35 o C flow) SCOP (average climate conditions) 35 o C Refrigerant (R40A) (kg) Operating voltage (v) Flow/ return tappings (BSPF) 3/4 /4 Min/max operating temperatures Air ( o C) -0/43-0/43-0/43 Sound power level at m (db(a)) Sound pressure level at m (db(a)) Air Source Heat Pumps *When fitted with a Grant MonoWave HP 00ltr cylinder ** In accordance with BS EN ISO 3744:00 Grant Aerona 3 Accessories HPIDFOOT/KIT HPIDINSU/KIT HPDHWBK HPIDBUFFER50 Flexi-foot kit with fixings ( x 600mm) Through wall insulation kit to fit -8mm flexi hose Automatic domestic hot water boost kit (timed) 50 Litre Buffer Tank Grant Aerona 3 Sealed System Kits HPAWSSK HPAWSSK8 HPAWSSK50 Litre sealed system kit for Aerona ASHP 8 Litre sealed system kit for Aerona ASHP 50 Litre sealed system kit for Aerona ASHP Aerona 3 Flexi-foot kit HPIDFOOT/KIT Aerona 3 Insulation kit HPIDINSU/KIT 5

16 Oil Boiler/ ASHP Hybrid Grant VortexAir Hybrid Range Designed by Grant 5-kW or -6kW blue flame oil boiler Heat Pump eligible for the RHI Boiler works as a stand alone unit and can be purchased separately from the heat pump Boiler can be fitted internally or externally Heat pump can be fitted at a later date Low level balanced flue kit included Grant VortexAir Hybrid Model HPIDAIR HPIDAIR ErP Rating Heat Pump Heating A++ A++ Hot Water* A A Boiler Heating A A Height (mm) Width (mm) Depth (mm) Heat Pump Empty Weight (kg) Boiler Empty 49 5 Combined Empty 80 8 Boiler Output (kw) Heat Pump Capacity (kw) Heat Pump Power input (kw) Heat Pump Running current (Max) (A)** 7.0 (5.3) 7.0 (5.3) Heat Pump COP (at 7 o C air/ 35 o C flow) Heat Pump SCOP (average climate conditions) 35 o C Heat Pump Refrigerant (R40A) (kg) Heat Pump Operating voltage (v) Heat Pump Flow/ return tappings (BSPF) /4 /4 Heat Pump Min/max operating temperatures Air ( o C) -0/43-0/43 Heat Pump Sound power level at m (db(a)) Heat Pump Sound pressure level at m (db(a)) * * When fitted with a Grant MonoWave HP 00ltr cylinder ** In accordance with BSENISO3744:995 6

17 Grant VortexAir Hybrid Oil Boiler/ ASHP Hybrid Oil boiler internally (Grant plume diverter utilised for flue) Heat Pump externally Grant VortexAir Accessories HPIDHEATMETER HPIDKW/HMETER Grant VortexAir Heat Meter Kit Grant VortexAir kw Meter HPIDFOOT/KIT Flexi-foot kit with fixings ( x 600mm) * *requires one set for boiler (if installed externally) and one set for heat pump Oil boiler combined with heat pump externally 7

18 Cylinders & Thermal Stores Grant HP Cylinder Range Duplex stainless steel mm and 8mm compression fittings No anode required Immersion heater Labelled colour-coded tappings Global warming potential (GWP) = less than 3 Ozone depletion potential (ODP) = 0 Grant MonoWave Heat Pump Cylinders Unvented indirect single coil duplex stainless steel HPMONO/ IND5 HPMONO/ IND50 HPMONO/ IND70 HPMONO/ IND00 HPMONOA/ IND00 HPMONO/ IND50 HPMONO/ IND300 HPMONO/ IND400 Capacity (ltrs) ErP Rating C C C B A C C C Pressure regulator (bar) Immersion (kw) * 3 * Expansion vessel (ltrs) Coil rating primary (kw) Standing heat loss (kw/4hrs) Height (mm) Diameter (mm) Weight empty (kg) Weight full (kg) * x 3kW immersion heaters Grant DuoWave Heat Pump Cylinders Unvented indirect twin coil duplex stainless steel HPDUO/ IND70 HPDUO/ IND00 HPDUO/ IND50 HPDUO/ IND300 HPDUO/ IND400 Capacity (ltrs) ErP Rating C B C C C Pressure regulator (bar) Immersion (kw) Expansion vessel (ltrs) Coil rating primary (kw) Solar (kw) Standing heat loss (kw/4hrs) Height (mm) Diameter (mm) Weight empty (kg) Weight full (kg)

19 HP MonoWave Connections A Hot out G B T+P valve H C Secondary return I D Heat pump flow E Heat pump return F Thermostat pocket A Immersion heater Cold In Immersion heater (300 & 400ltr models only A Cylinders & Thermal Stores MonoWave HP 5ltr, 50ltr, 70ltr, 00ltr & 50ltr models B H E F D C G MonoWave HP 300ltr & 400ltr models B H E F D C I G HP MonoWave Connections A B C D E F Hot out T+P valve Heat pump flow Heat pump return Secondary return Thermostat pocket (top) G H I J K Immersion heater Thermostat pocket (bottom) Solar flow Cold in Solar return A A E B C D B C D DuoWave HP 70ltr model G J K I F H DuoWave HP 00ltr, 50ltr, 300ltr & 400ltr models E G J K I F H 9

20 Cylinders & Thermal Stores Grant Solar Cylinder Range Grant DuoWave Solar Cylinders Unvented direct solar single coil duplex stainless steel GDUO/ DIR70 GDUO/ DIR00 GDUO/ DIR50 GDUO/ DIR300 GDUO/ DIR400 Capacity (ltrs) ErP Rating B C C C C Pressure regulator (bar) Immersion (kw) Expansion vessel (ltrs) Coil rating primary (kw) Standing heat loss (kw/4hrs) Height (mm) Diameter (mm) Weight empty (kg) Weight full (kg) Grant DuoWave Solar Cylinders Unvented indirect solar single coil duplex stainless steel GDUO/ IND70 GDUO. IND00 GDUO/ IND50 GDUO/ IND300 GDUO/ IND400 GDUO/ IND500 Capacity (ltrs) ErP Rating B C C C C D Pressure regulator (bar) Expansion vessel (ltrs) Coil rating primary (kw) Solar (kw) Standing heat loss (kw/4hrs) Height (mm) Diameter (mm) Weight empty (kg) Weight full (kg)

21 DuoWave Solar Connections A Hot out B T+P valve C Primary return (indirect only) D Secondary return E Top thermostat pocket (indirect only) F Primary flow (indirect only) G Solar return H Immersion heater (direct models only) I Thermostat pocket (bottom) J Cold mains in K Solar flow L Immersion heater DuoWave Solar Cylinder Cylinders & Thermal Stores A A B D B D C L F E G L DuoWave Direct models J K I H DuoWave Indirect models J G K I

22 Cylinders & Thermal Stores Grant DuoWave Plus Cylinders Grant DuoWave Plus Solar Cylinders Open vented indirect solar triple coil duplex stainless steel GDUO/PLUS300 Capacity (ltrs) 8 ErP Rating C Coil rating primary (kw).6 Coil rating secondary (kw) 8.5 Solar (kw) 6 Standing heat loss (kw/4hrs). Height (mm) 745 Diameter (mm) 580 Weight empty (kg) 57 Weight full (kg) 357 Grant DuoWave Plus Solar Cylinders Unvented indirect solar triple coil duplex stainless steel GDUO/PLUS300U Capacity (ltrs) 8 ErP Rating C Pressure regulator (bar) 3 Expansion vessel (ltrs) 4 Coil rating primary (kw).6 Coil rating secondary (kw) 8.5 Solar (kw) 6 Standing heat loss (kw/4hrs). Height (mm) 745 Diameter (mm) 580 Weight empty (kg) 57 Weight full (kg) 357 A Grant DuoWave Plus connections DuoWave Direct models DuoWave Plus Open Vented/Unvented models B C M L D H E G J I F K A B C D E F G H I J K L M Hot out T+P valve Secondary return Primary return Solid fuel flow Thermostat pocket (top) Solid fuel return Primary flow Solar return Solar flow Thermostat pocket (bottom) Cold mains in Immersion heater

23 Grant ThermaWave Stores Grant ThermaWave Stores Open vented duplex stainless steel thermal stores GTHERM/50 GTHERM/300 GTHERM400 Capacity (ltrs) ErP Rating C C C Coil rating solar (kw) Standing heat loss (kw/4hrs) Height (mm) Cylinders & Thermal Stores Diameter (mm) Weight empty (kg) Weight full (kg) DHW Sealed system duplex stainless steel thermal stores c/w hot water coil GTHERM300HWU GTHERM400HWU GTHERM500HWU Capacity (ltrs) ErP Rating C C D Coil rating solar (kw) Coil rating DHW (kw) Standing heat loss (kw/4hrs) Height (mm) Diameter (mm) Weight empty (kg) Weight full (kg) DHW Open vented duplex stainless steel thermal stores c/w hot water coil GTHERM300HW GTHERM400HW GTHERM500HW Capacity (ltrs) ErP Rating C C D Coil rating solar (kw) Coil rating DHW (kw) Standing heat loss (kw/4hrs) Height (mm) Diameter (mm) Weight empty (kg) Weight full (kg)

24 Cylinders & Thermal Stores Grant ThermaWave Connections A AA A BB C B D C B D E G* F E G F G H ThermaWave DHW unvented models ThermaWave DHW open-vented models P M X K R U L T N Q W ThermaWave open-vented models I M P V K S L O R T U X J N Q W A B Output seven (e.g to DHW kit or flow to DHW cylinder + OSV) T&P Valve (/ BSPF for 50L & 300L and 3/4 for 400L & 500L models) C Input one (e.g flow from boiler if DHW is fitted) D E F G Output one (e.g CH flow if no DHW is fitted) Thermostat pocket Input two (e.g flow from boiler if no DHW is fitted) Output two (e.g CH flow if DHW is fitted) G* Output two alternative position (e.g. if less DHW is required) H I J K L M N O P Q R S T U V W X 8mm gravity flow (e.g solid fuel) Input three (e.g return from DHW kit or cylinder) Output three (e.g to UFH if high capacity) Immersion heater Thermostat pocket Input four (e.g flow from heat pump) Output four (e.g return to boiler) 8mm gravity return (e.g solid fuel) Input five (e.g return from CH) Output five (e.g UFH flow if low capacity) Solar coil return Immersion heater Thermostat pocket Solar coil flow Input six (e.g return from UFH) Output six (e.g return to heat pump) mm fill and drain point AA Cold mains BB DHW out Note: The inputs and outputs highlighted above may vary depending upon the technologies being connected to the thermal store, and if a nominal quantity of domestic hot water is also required. For further guidance consult the installation manual or Grant Technical Services. 4

25 Grant ThermaWave DHW Performance Data Grant ThermaWave DHW Stores Performance Data Capacity (ltrs) Draw of f * (0l/min at 70 O C) Reheat time (mins) 4 Draw of f * (0l/min at 70 O C) Reheat time (mins) 0 4 Cylinders & Thermal Stores Draw of f 3 * (0l/min at 70 O C) Reheat time (mins) Note: Draw of f provides a final mixed water temerature (e.g. for bath) of 45 o C. Draw of f is the top third of the store. Draw of f is the top /3 of the store. Draw of f 3 is the full store (without solar thermal input). Reheat times relate to raising the same volume of water back to 70 o C. Grant ThermaWave DHW Components Open Vented Models ltr shock arrestor mm thermostatic mixing valve mm x mm / BSPF fitting 3 bar/6bar inlet group (optional extra) Sealed System Models ltr shock arrestor mm thermostatic mixing valve mm x mm / BSPF fitting 3 bar/6bar inlet group (optional extra) Expansion vessel Expansion vessel bracket/hose Reducer fitting (400/500ltr models only) mm x mm x 3/4 BSPF fitting / BSPM to 5mm fitting (90 o ) Filling loop kit PRV & Pressure gauge 80 o C limit stat Electrical control box ThermaWave DHW ThermaWave 5

26 Solar Thermal Systems Grant Solar Thermal Range Available in kits High efficiency flat plate collector Multifunctional controller In-roof, on-roof & flat roof options New compact pump station Solar Keymark approved Solar Keymark Collector Information Length (mm) 043 Width (mm) 43 Depth (mm) 80 Collector gross area (m ).34 Aperture/absorber area (m ).4 Weight (kg) 40 Glass type ESG, Durasolar P+ Sandy Glass Thickness (mm) 3. Efficiency (%) 8.6 Ef fective thermal capacity(kj/m K ) 60 Conversion factor ( ) 0.86 Linear heat loss coef ficient (a ) 4.4 Linear heat loss coef ficient (a ) (W/m K ) Stagnation temperature * ( o C) 77 Maximum operating pressure (bar) 0 Fluid content (ltr).6 Tilt angle (maximum/minimum) ( o ) 0/90 Pressure drop (at.5l/min solar fluid) (mbar) 05 *Test conditions - Irradiance 000W/m Ambient temperature 30 C 6

27 8.6% Collector efficiency Solar irradiation in the UK and Ireland The diagram below shows the total average solar radiation falling on m surface, inclined at 30 to the horizontal, measured in kilowatt-hours. The average property requires approximately 3,000 kwh per year for domestic water heating. Solar Thermal Systems How to calculate the number of collectors required South Direction of roof Solar radiation (see above map) Number of people per household kwh/year < South west/ South East West East Cylinder requirements are litres capacity per m of nett collector area. To simplify this, for a -collector system of x.4 = 4.8m, you would require a cylinder of approximately litres. This should be suf ficient for 4 people and satisfy up to 70% of your hot water demand per annum. 7

28 Solar Thermal Systems Sahara Portrait On-Roof Kits GSSKIT0 Collector Bronze On-Roof Solar Collector (Bronze) Connection kit flow and return Collector on roof extra set Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve Roof Anchors: Anchors for profile tile (Pack of ) Anchors for flat tile (Pack of ) Anchors for slate tile (Pack of ) QTY Pks* Pks* Pks* GS773 GS46 GS74 GS54H GS765 GS076 GS07 GS074 GS073 GS48 GS088 GS090 GSSKIT Collector Bronze On-Roof Solar Collector (Bronze) Connection kit flow and return Connection Kit collector to collector Collector portrait rails and fixings Pump Station Controller Solar Fluid 0 litre Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve Roof Anchors: Anchors for profile tile (Pack of ) Anchors for flat tile (Pack of ) Anchors for slate tile (Pack of ) QTY 3 Pks* 3 Pks* 3 Pks* GS773 GS46 GS068 GS74 GS54H GS765 GS075 GS076 GS07 GS074 GS073 GS48 GS088 GS090 GSsKIT 3 Collector Bronze On-Roof Solar Collector (Bronze) Connection kit flow and return Connection Kit collector to collector Collector portrait rails and fixings Collector on roof extension kit Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve Roof Anchors: Anchors for profile tile (Pack of ) Anchors for flat tile (Pack of ) Anchors for slate tile (Pack of ) Qty 3 4 Pks* 4 Pks* 4 Pks* GS773 GS46 GS068 GS74 GS74 GS54H GS765 GS076 GS07 GS074 GS073 GS48 GS088 GS090 *This is the minimum number of roof anchors required. For MCS compliant installations the number of roof anchors must be calculated using the method given in MCS0 8

29 Sahara Portrait In-roof Kits GSSKIT5 Collector Bronze In-Roof (TILE) Solar Collector (Bronze) Connection kit flow and return Collector Portrait In-Roof Kit - Tile Roof Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY GS773 GS46 GS GS5545 GS54H GS765 GS076 GS07 GS074 GS073 Solar Thermal Systems GSSKIT6 Collector Bronze In-Roof (SLATE) QTY Solar Collector (Bronze) Connection kit flow and return Collector Portrait In-Roof Kit - Slate Roof Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve GS773 GS46 GS GS5545 GS54H GS765 GS076 GS07 GS074 GS073 GSSKIT3 Collector Bronze In-Roof (TILE) QTY Solar Collector (Bronze) Connection kit flow and return Connection Kit collector to collector Collector Portrait In-Roof Kit - Tile Roof Pump Station Controller Solar Fluid 0 litre Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve GS773 GS46 GS068 GS GS5544 GS54H GS765 GS075 GS076 GS07 GS074 GS073 GSSKIT7 Collector Bronze In-Roof (slate) QTY Solar Collector (Bronze) Connection kit flow and return Connection Kit collector to collector Collector Portrait In-Roof Kit - Slate Roof Pump Station Controller Solar Fluid 0 litre Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve GS773 GS46 GS068 GS GS5544 GS54H GS765 GS075 GS076 GS07 GS074 GS073 9

30 Solar Thermal Systems Sahara Portrait In-Roof Kits GSSKIT4 3 Collector Bronze In-Roof (TILE) Solar Collector (Bronze) Connection kit flow and return Connection kit connector to connector Collector portrait In-Roof kit - Tile Roof Collector portrait In-Roof extension - Tile Roof Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY 3 GS773 GS46 GS068 GS GS5544 GS555 + GS5545 GS54H GS765 GS076 GS07 GS074 GS073 GSSKIT8 3 Collector Bronze In-Roof (SLATE) Solar Collector (Bronze) Connection kit flow and return Connection kit connector to connector Collector portrait In-Roof kit - Slate Roof Collector portrait In-Roof ext - Slate Roof Pump Station Controller Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY 3 GS773 GS46 GS068 GS GS5544 GS GS5550 GS54H GS765 GS076 GS07 GS074 GS073 Sahara Portrait Flat Roof Kits GSSKIT5 Collector Bronze Flat-Roof Solar Collector (Bronze) Connection kit flow and return Connection Kit collector to collector Collector portrait Flat Roof rails & fixings Collector portrait Flat Roof Kit Collector portrait Flat Roof Cruciform Pump Station Controller Solar Fluid 0 litre Solar Fluid 0 litre Expansion Vessel 8 litre Expansion Vessel pipe connections Expansion Vessel bracket and valve QTY GS773 GS46 GS068 GS74 GS08 GS69 GS54H GS00 GS075 GS076 GS07 GS074 GS073 For bespoke kits please contact our sales team on +44 (0)

31 CombiSOL & WinterSOL kits Grant CombiSOL Designed by Grant Compatible with most combination boilers Accurately regulates inlet water temperature Solar Thermal Systems COMSOL3 Description Thermostatic Solution for linking Combi boilers to Solar Thermal pre-heat cylinders Grant WinterSOL Designed by Grant Provides a fully heated cylinder of hot water at times of low solar gain Operates during programmed hot water periods WINTERSOL Description Recirculating/ Sanitising solution (heats complete solar cylinder when there is no solar gain) 3

32 Biomass Boilers Grant Vecta Internal Range Highly efficient MCS approved Top fill 60kg integrated pellet store with optional 40kg bolt on side pellet store Automatic pellet feed and ignition Award winning product Automatic wash system for condensing unit Self-cleaning system for heat exchanger and burner brazier Simple to install and maintain Optional remote logo indicator kit Exceptionally quiet Factory fitted Lambda sensor Nett efficiency: Part load (condensing): 97.5% Full load (condensing): 0.5% Exempt under the Clean Air Act Vecta Condensing Wood Pellet Boilers Internal white cased model WVP4/6 Boiler Output (kw) 4-6 Boiler Weight (empty) (kg) 55 Boiler Weight (full) (kg) 350* Flue (mm) 5 Wash system (condensing unit) (mm) 5 Flow/return connection (mm) Condensate drain /4 female Water content (litres) 35 Electrical supply ~30V ph 50Hz 5A fused Integrated hopper size (kg) 60 *including water content and full hopper 3

33 Grant Vecta Internal Dimensions FRONT VIEW Biomass Boilers RIGHT SIDE VIEW Front view FRONT VIEW Right side view LEFT SID VIEW RIGHT SIDE VIEW DATE: //6 JOB TITLE: VECTA 4_6kW DRAWING TITLE: VECTA 4_6kW DIMENSIONS DWG NO: 6 REV: 0 REV DISCRIPTION: REAR VIEW 7 FRONT VIEW 86 TOP VIEW 88 LEFT SIDE VIEW Top view Left side view

34 Biomass Boilers Grant Vecta External Range Highly efficient Top fill 80kg integrated pellet store with optional 40kg bolt on side pellet store Weather proof powder coated finish Includes remote logo indicator kit Automatic pellet feed and ignition Automatic wash system for condensing unit Self-cleaning system for heat exchanger and burner brazier Simple to install and maintain Factory fitted Lambda sensor Nett efficiency: Part load (condensing): 97.5% Full load (condensing): 0.5% Exempt under the Clean Air Act Vecta Condensing Wood Pellet Boilers External powder coated module WVP4/6EXT Boiler Output (kw) 4-6 Boiler Weight (empty) (kg) 65 Boiler Weight (full) (kg) 380* Flue (mm) 5 Wash system (condensing unit) (mm) 5 Flow/return connection (mm) Condensate drain /4 female Water content (litres) 35 Electrical supply ~30V ph 50Hz 5A fused Integrated hopper size (kg) 80 *including water content and full hopper 34

35 Grant Vecta External Dimensions Biomass Boilers Front view Left view Top view 35

36 Biomass Boilers Vecta Internal Side Pellet Store 40kg capacity White casing Fits to the right hand side of the boiler (only) Top fill via hinged lid with gas struts Comes complete with feed auger and cable Combined pellet storage capacity (boiler + side store) of 00kg Optional Vecta Internal Side Pellet Store WVP4/6STORE Capacity 40kg Height (mm) 6 Height with open lid (mm) 670 Width (mm) 650 Width (including boiler) (mm) 40 Depth (mm) 86 Weight (empty) (kg) 96kg Weight (full) 36kg FRONT VIEW Vecta Internal with side pellet store 36

37 Vecta External Side Pellet Store 40kg capacity Powder coated stainless steel casing Fits to the right hand side of the boiler (only) Top fill via hinged lid with gas struts Comes complete with feed auger and cable Combined pellet storage capacity (boiler + side store) of 0kg Supplied with weather proof external flue system inspection pipe Biomass Boilers Optional Vecta Internal Side Pellet Store WVP4/6EXTSTORE Capacity 40kg Height (mm) 6 Height with open lid (mm) 843 Width (mm) 68 Width (including boiler) (mm) 55 Depth (mm) 793 Weight (empty) (kg) 80 Weight (full) 0 Vecta External with side pellet store 37

38 Biomass Boilers Grant Spira Biomass Range Highly efficient condensing boiler MCS approved Modulating burner Integrated pellet store 5mm conventional flue Automatic pellet feed and ignition Award winning condensing heat exchanger Flue box with integral fan/ draught stabiliser Automatic wash system for condensing unit Exempt under the Clean Air Act Product Code Internal Standard Models Including Pellet Store and Auger(s) Output Btu/h x000 kw Description WPS58RH kW wood pellet boiler c/w 0kg right hand hopper & auger WPS58LH kW wood pellet boiler c/w 0kg left hand hopper & auger WPS58RH kW wood pellet boiler c/w 00kg right hand hopper & auger WPS58LH kW wood pellet boiler c/w 00kg left hand hopper & auger WPS66RH kW wood pellet boiler c/w 0kg right hand hopper & auger WPS66LH kW wood pellet boiler c/w 0kg left hand hopper & auger WPS66RH kW wood pellet boiler c/w 00kg right hand hopper & auger WPS66LH kW wood pellet boiler c/w 00kg left hand hopper & auger WPS936RH kW wood pellet boiler c/w 0kg right hand hopper & auger WPS936LH kW wood pellet boiler c/w 0kg left hand hopper & auger WPS936RH kW wood pellet boiler c/w 00kg right hand hopper & auger WPS936LH kW wood pellet boiler c/w 00kg left hand hopper & auger WPS/ x 6kW wood pellet boilers c/w 40kg dual hopper & augers WPS5/ kW & 36kW wood pellet boilers c/w 40kg dual hopper & augers WPS8/ x 36kW wood pellet boilers c/w 40kg dual hopper & augers 38

39 Grant Spira Technical Information Spira Model Units kw Maximum heat output Btu/hr 6,400 88,700,800 Biomass Boilers Flow connection BSP F F /4 F Return connection BSP F F /4 F Water content Ltr Waterside resistance rt = 0 o C mbar 50 Waterside resistance rt = 0 o C mbar 40 Mains water (cleaning system) bar bar operating pressure Condensate connection - /4 BSP Female Conventional flue - 5mm (5 ) Combustion chamber draught requirement mbar 0.0 to 0.5 (running) Maximum static head m 5 Minimum circulating head m Boiler temperature set point range o C 55 to 75 Boiler temperature cut out point o C 65 to 80 Minimum return temperature o C 40 Water system overheat thermostat cut-out o C 00 Burn-back overheat thermostat cut-out o C 90 Electricity supply - ~30V ph 50Hz 3A fused Max operating pressure - sealed system bar.0 Max operating pressure - open system bar.0 Maximum auger length (bulk hopper) m 6.0 Maximum auger speed (bulk hopper) rpm 30 Minimum flue length m.6 Maximum flue length m.0 Heating element rating Watts 450 Intermediate auger motor power Watts 55 Intermediate auger motor starting current Amps 0.64 Intermediate auger motor running current Amps 0.64 Intermediate auger speed rpm 8. Flue fan motor power Watts 3 Flue fan motor starting current Amps 0.7 Flue fan motor running current Amps 0.3 Cleaning solenoid power Watts 0 Cleaning solenoid current Amps Burner fan motor power Watts 56 Total burner start current Amps.5 Total burner run current Amps

40 Biomass Boilers Spira Single Boiler Dimensions A 5 5 B A C C Front view C Air vent Wash system B 5 55 A Flow connection Return connection Condensate drain Hopper wiring centre A 5 55 C B 55 Flow connection Return connection Hopper wiring centre Drain cock 77 Air vent A Wash B system C Side view ash stem Air vent Air vent Wash system Wash system Air vent Flow connection Return connection Flow Hopper connection wiring centre Return connection Condensate Drain drain Hopper cock wiring centre Hopper wiring centre Flow connection Return connection Drain cock Wash system Rear view Grant Spira Model Dimensions (mm) a b C 5-8kW 0kg left/right hand hopper kW 00kg left/right hand hopper kW 0kg left/right hand hopper kW 00kg left/right hand hopper kW 0kg left/right hand hopper kW 00kg left/right hand hopper

41 79 Spira Double Boiler Dimensions B Biomass Boilers B B Front view Side view Air vent Air vent Air vent Air vent Rear view Air vent Wash Wash Flow system system connection Wash Flow Return Return system connection connection Hopper connection wiring Hopper Condensate Return centre wiring drain connection Condensate Hopper centre drain wiring Condensate Drain centre drain cock Drain cock Drain cock Flow Flow connection connection Flow connection Return connection Return connection Return Drain connection cock Drain cock Air vent Wash Wash system system Drain cock Wash system Grant Spira Model Dimensions (mm) a -5KW 40kg double hopper 0 5-6kW 40kg double hopper 0 8-7kW 40kg double hopper 0 Boiler and Hopper Weights (kg) Spira model 5-8 & Boiler - less burner & fan box (empty) 0 3 Burner Fan box 5 5 Total boiler weight (empty) Total boiler weight (full) kg pellet hopper incl auger (empty) kg pellet hopper incl auger (full) kg pellet hopper incl auger (empty) kg pellet hopper incl auger (full) Auger kg pellet hopper incl x augers (empty) kg pellet hopper incl x augers (full) 8 8 4

42 Biomass Boilers Grant SpiraPod External Housing Purpose built external housing for the Spira Accommodates all Spira models from 5-36kW Designed and manufactured by Grant Fully weather proof steel casing Iconic Grant grey powder coated finish Top fill integral hopper with 90kg capacity Suitable for vacuum feed Optional internal pellet vacuum system Lockable doors Sealed system kit can be fitted within the pod SpiraPod Outdoor Boiler Housing Description WPSPOD8 SpiraPod 5-8kW wood pellet boiler and external casing WPSPOD6 SpiraPod 6-6kW wood pellet boiler and external casing WPSPOD36 SpiraPod 9-36kW wood pellet boiler and external casing 4

43 Grant SpiraVac Wood Pellet Vacuum Designed and manufactured by Grant Simple to install Gives more flexibility with boiler installation Can be retrofitted to existing boiler Maximum hose length of 0m Lifts pellets up to a height of 3m Only for use with the Grant Spira boiler ranges Biomass Boilers Grant SpiraVac Models Code WPV/KIT5INT WPV/KIT0INT WPV/KIT5INT WPV/KIT0INT WPV/KIT5POD WPV/KIT0POD WPV/KIT5POD WPV/KIT0POD Description SpiraVac Internal Spira Vacuum kit - 5 metres SpiraVac Internal Spira Vacuum kit - 0 metres SpiraVac Internal Spira Vacuum kit - 5 metres SpiraVac Internal Spira Vacuum kit - 0 metres SpiraVac SpiraPod Vacuum kit - 5 metres SpiraVac SpiraPod Vacuum kit - 0 metres SpiraVac SpiraPod Vacuum kit - 5 metres SpiraVac SpiraPod Vacuum kit - 0 metres External bulk pellet store Flexible hoses SpiraVac vacuum unit Boiler/Hopper SpiraVac auger unit Internal Spira model 43

44 Biomass Flues Grant Biomass Flue Systems Conventional stainless steel vertical flue Twist-lock bayonet jointing system Stainless steel white or black finish Suitable for Spira and Vecta boilers Advanced corrosion resistant design Finish Description WPW/30 WHITE 30 bend WPW/45 WHITE 45 bend WPW/ADJ50 WPW/EXT00 WP/WEXT333 WPW/EXT500 WPW/EXT000 WHITE WHITE WHITE WHITE WHITE 75-50mm adjustable extension c/w locking band and gasket 00mm extension c/w locking band and gasket (effective length 60mm) 333mm extension c/w locking band and gasket (effective length 93mm) 500mm extension c/w locking band and gasket (effective lenght 460mm) 000mm extension c/w locking band and gasket (effective length 960mm) WPW/WB60 WHITE Wall bracket (60 mm) WPW/WB300 WHITE Wall bracket (300 mm) WPW/IP WHITE Inspection pipe WPW/CA WHITE Flue Icid to chimflex adaptor WPW/FP WHITE Firestop Plate ( piece) WPW/SP WHITE Support Plate ( pieces) WPW/TC WHITE Trim Collar for Wall Sleeve (45 ) WPB/30 BLACK 30 bend WPB/45 BLACK 45 bend WPB/ADJ50 WPB/EXT00 WPB/EXT333 WP/BEXT500 WPB/EXT000 BLACK BLACK BLACK BLACK BLACK 75-50mm adjustable extension c/w locking band and gasket 00mm extension c/w locking band and gasket (effective length 60mm) 333mm extension c/w locking band and gasket (effective length 93mm) 500mm extension c/w locking band and gasket (effective lenght 460mm) 000mm extension c/w locking band and gasket (effective length 960mm) WPB/WB60 BLACK Wall bracket (60 mm) WPB/WB300 BLACK Wall bracket (300 mm) WPB/IP BLACK Inspection pipe WPB/CA BLACK Flue Icid to chimflex adaptor WPB/AP BLACK Anchor plate/ Chimflex adaptor WPB/FP BLACK Firestop Plate ( piece) 44

45 Grant Biomass Flue Systems WPB/SP BLACK Support Plate ( pieces) WPB/CANT BLACK Cantilever (570mm) WPB/GB BLACK Guy wire bracket WPB/LBEXT BLACK Structural locking band WPB/RC BLACK Rain cap WPB/RS BLACK Roof support s/s band WPB/SC BLACK Storm collar WPB/TP BLACK Intermediate top plate WPB/WS BLACK Wall support side plate WPB/TC BLACK Trim Collar for Wall Sleeve (45 ) Biomass Flues Biomass flue accessories WPB/SLE Wall sleve (45 o ) (also requires WPB/TC or WPW/TC x) WPB/UF00 WPB/PFL Uni flashing (80-00mm) Pitched lead flashing Conventional stainless steel flexible flue liner kits Flexi flue liner Stainless steel smooth bore liner Suitable for all Grant wood pellet boilers Easy to install Finish Description WPWKIT6/5 WHITE 6 metre 5mm liner (inc box kit) WPWKIT8/5 WHITE 8 metre 5mm liner (inc box kit) WPWKIT0/5 WHITE 0 metre 5mm liner (inc box kit) WPBKIT6/5 BLACK 6 metre 5mm liner (inc box kit) WPBKIT8/5 BLACK 8 metre 5mm liner (inc box kit) WPBKIT0/5 BLACK 0 metre 5mm liner (inc box kit) 45

46 Wood Pellet Stores Grant Wood Pellet Stores Designed and manufactured by Grant Galvanised steel construction Quick seal joints Universal auger or vacuum connection Internal or external installation Low level connection for ease of filling Extremely robust construction Easy access maintenance door for cleaning Code Size (tonne) Grant Pellet Store Models Finish Footprint (metre) Height (mm) Weight (kg) WPXG05TP 0.5 Painted x 375 * 70 WPXG075TP 0.75 Painted x 75 * 83 WPXG5T.5 Galvanised x WPXGT Galvanised x WPXG5T.5 Galvanised x WPXG3T 3 Galvanised x WPXG35T 3.5 Galvanised x WPXG4T 4 Galvanised x WPXG5T 5 Galvanised x WPXG6T 6 Galvanised x * Please allow additional clearance of 450mm for store lid Note: Not suitable for use with Grant Vecta boilers Painted Pellet Store 500kg and 750kg models come ready assembled 46

47 Grant MagOne Magnetic Central Heating Filter High performance heavy duty filter Easy clean, easy drain design 000 gauss neodymium magnet Full bore flat face 8mm isolation valves with 8-mm reducers 0 C max working temperature 6 bar max working pressure 500ml dosing capacity Manual air bleed 360 o Installation Suitable for systems up to 36kW, larger systems use two in parallel circuit MagOne Filter VM0/X Description Vortex MagOne universal /8mm magnetic central heating filter Note: Please allow enough clearance around the MagOne to ensure the isolating valves can be fully closed. It is recommended that a clearance of at least 50mm is given to enable the magnet and filter to be removed during servicing. Sufficient clearance must also be given to ensure that the MagOne can be drained easily into a suitable container. 47

48 Controls Energy Management Controls GEO360 Reduces heating bills Easier system installation and commissioning Environmentally friendly Suitable for systems up to 65kW Individually controlled heat circuits Option to switch the system to hot water priority Allows a number of heating appliances to be combined, including renewable technologies Provides boiler lead/lag rotation, equalising appliance running time Maximises overall boiler/ appliance efficiency Tailored system concept drawings for both plumbing and wiring available GES64 Grant Energy Management Controllers Product Code Description ErP Class Package Uplift GEO360/8 GEO360 Weather compensator with 8mm valves suitable for Vortex Pro 6-46kW, Vortex Eco 6-35kW) With on/of f heaters With modulating heaters VII 3.5% VI 4% GEO360/35 GEO360 Weather compensator with 35mm valves (suitable for Vortex Pro 46-70kW) With on/of f heaters With modulating heaters VII 3.5% VI 4% GEO360/KV6 GEO360 Weather compensator with KV6.3 valve (suitable for Vortex Eco 5-kW, Eco Wallhung -kw) With on/of f heaters With modulating heaters VII 3.5% VI 4% GEO360/KV8 GEO360 Weather compensator with KV8 valve (suitable for Vortex Pro 5-6kW, Vortex Eco -6kW, Spira 6-36kW) With on/of f heaters With modulating heaters VII 3.5% VI 4% GHS/GEO360 GEO360 for Grant low loss header system (no valve body) With on/of f heaters With modulating heaters VII 3.5% VI 4% GES64 GES64 sequence controller (for to 4 heat sources) With on/of f heaters With modulating heaters VII 3.5% VI 4% 48

49 Low Loss Headers Controls Grant Low Loss Headers (for systems up to 70kW) GHS70/5 GHS70/53 GHS70/54 GHS70/55 Description flow and return distributor ( zone) flow and return distributor (3 zone) flow and return distributor (4 zone) flow and return distributor (5 zone) GHS70/56 flow and return distributor (6 zone) GHS60/5 /4 hydraulic switcher Accessories GHS/WF00 GHS/WF50 Header bracket set wrap over 00mm Header bracket set wrap over 50mm GHS/WFHV Header bracket set 90 GHS0569 GHS/066M GHS/SG50 /4 connector (quantity: ) Please note: connectors per switcher required Isolation valve (quantity: ) Please note: valves per pump station required Safety set up to 50kW (3 bar PRV) Please note: if 70kW please use GHS/SG00 Technical Specification Maximum flow rate Insulation box Pump unit connection Hydraulic switcher connection Side connection up to 3m 3 /h, 6bar 0 x 0 x 508mm (min) - 508mm (max) (depending on model) male /4 male 3 /4 female Hydraulic switcher t0k) Distributor t0k) 49

50 Controls Low Loss Headers Grant Low Loss Headers (for systems up to 65kW) GHS80/5 GHS80/53 GHS80/54 GHS80/55 Description /4 flow and return distributor ( zone) /4 flow and return distributor (3 zone) /4 flow and return distributor (4 zone) /4 flow and return distributor (5 zone) GHS80/56 /4 flow and return distributor (6 zone) GHS80/570 vertical hydraulic switcher Accessories GHS/WF60 GHS/WFHV60 GHS07699 GHS/55AMMS GHS/HT07 GHS/SG00 Header bracket set wrap over 60mm Header wall fixing set - 60mm connection kit /4 isolation valve (quantity: ) - please note: valves per pump station required nut & gasket for /4 isolation valves (quantity: ) - please note: sets of nut & gaskets per pump station required Safety set up to 00kW (3 bar PRV) Technical Specification Maximum flow rate Insulation box Pump unit connection Hydraulic switcher connection Side connection up to 7m 3 /h, 6bar 5 x 5 x 65mm (min) - 65 (max) (depending on model) /4 male male male Distributor and hydraulic switcher Zone pump kit (constant) 50

51 Zone Pump Kits Controls Zone Pump Kits (for systems up to 70kW) GHS/CT0 Description Constant temperature/variable speed 6 metre zone pump kit GHS/CT0 Constant temperature/variable speed 8 metre zone pump kit GHS/VT03 GHS/VT04 Variable temperature/variable speed 6 metre zone pump kit Variable temperature/variable speed 8 metre zone pump kit Zone Pump Kits (for systems up to 65kW) GHS/CT05 GHS/CT06 GHS/VT07 GHS/VT08 Description 3mm constant temperature/variable speed 7 metre zone pump kit 3mm constant temperature/variable speed 8 metre zone pump kit 3mm variable temperature/variable speed 7 metre zone pump kit 3mm variable temperature/variable speed 8 metre zone pump kit Comprises Technical Specification Zone pump kits (constant speed) Unmixed HE Zone pump, isolator ball valves, temperature gauges and non-return valve Connection sizes Dimensions and /4 BSP 50 x 380 x 90mm Maximum temperature 0 C Application Flow For power up to 50kW and maximum flow 50 l/hr 6m, 7m or 8m circulating pump Comprises Zone pump kits (variable speed) Unmixed HE Zone pump, isolator ball valve, temperature gauges and non-return valve, 3-port mixing valve Connection sizes Dimensions Maximum temperature Application Flow and /4 BSP 50 x 380 x 90mm 0 C For power up to 35kW and maximum flow 500 l/hr 6m, 7m or 8m circulating pump, 3-way mixing valve for weather compensation using a Grant GEO360 Control 5

52 This leaflet is accurate at the time of printing but as Grant UK has a policy of continual improvement it may be superseded. We reserve the right to amend specifications without prior notice. The statutory rights of the consumer are not af fected. All products manufactured under I.S. EN ISO 900. Grant UK additionally holds ISO 400 accreditation. THE GRANT EZ-FIT FLUE SYSTEM is a trade mark of Grant Engineering Ireland ULC. Grant Aerona, Grant Spira, Grant Vecta, Grant Vortex, Grant VortexBlue, Grant MagOne, Grant VortexAir,Grant Solar, Grant Aurora, Grant Sahara, Grant CombiSOL, Grant WinterSOL, Grant MonoWave, Grant DuoWave, Grant ThermaWave, Euroflame and Multi Pass are registered trade marks of Grant Engineering Ireland ULC. The contents of this leaflet are fully protected by copyright and nothing may be reproduced without permission from Grant Engineering Ireland ULC. Grant Engineering (UK) Ltd Hopton House, Hopton Industrial Estate, Devizes, Wiltshire, SN0 EU t: +44 (0) f: +44 (0) e: info@grantuk.com w: UKBPG REV087 5