User Manual AURA ELECTRIC FIREPLAC E

Size: px

Start display at page:

Download "User Manual AURA ELECTRIC FIREPLAC E"

Jasper Dawson
5 years ago
Views:

this product. Observe all safety instructions and information.

1 User Manual Item# : ES-307-ES Model#: BLT-999T-1 AURA ELECTRIC FIREPLAC E READ & SAVE THESE INSTRUCTIONS Carefully read and review before assembling, installing, operating or maintaining this product. Observe all safety instructions and information. FAILURE TO FOLLOW WARNINGS & OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.

2 Important: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty. INSTALLATION INSTRUCTIONS GENERAL Read all instructions before using this appliance. This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet from the front and sides of this appliance. Caution: Extreme caution is necessary when any heater is used near children or disabled persons. Never leave any heater unattended. Always unplug this appliance when not in use. Do not operate any heater with a damaged cord or plug or after the appliance malfunctions, or has been dropped or damaged in any manner. Any repairs to this appliance must be carried out by a qualified service person Under no circumstances should this appliance be modified. Parts having to be removed for servicing must be replaced prior to operating this appliance again. Do not use outdoors. This appliance is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate this appliance where it may fall into a bathtub or otherwise become exposed to water. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas and where it will not be tripped over. To disconnect this appliance, turn controls to the off position, then remove the plug from the outlet. Connect to properly grounded outlets only. This appliance, when installed must be electrically grounded in accordance with local codes, and the National Electrical Code, ANSI/NFPA No. 70. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire or damage the appliance. To prevent possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. This appliance has hot and arching or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. This appliance should not be used as a drying rack for clothing, nor should Christmas stockings or decorations be hung on or near it. -1-

3 17. Use this appliance only as described in this manual. Any other use not recommended 18. Avoid the use of an extension cord because the extension cord may overheat and SPECIFICATIONS Dimensions LxWxH Net Weight Voltag e Frequency Watts Heater Rating 15.75"x7.52"x19.2" 22.4 lbs V~ 60 Hz 1350 W 4606 BT U ELECTRICAL CONNECTION A 15 Amp, 110 Volt, 60 Hz circuit withaproperly grounded outlet is required to operate this appliance. The fireplace must be on adedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard with a6.5 ft long 3wire cord, exiting out the back of the fireplace. Plan the installation to avoid the use of an extension cord. WARNING: Electrical outlet wiring must comply with local building codes and other WARNING: ce if any part of it has become wet. Immediately call a system which has been wet. -2-

4 . The cord has a plug as shown in (A) of Figure 1 given below. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip) T METAL SCREW GROUNDING PIN (A) COVER OF GROUNDED OUTLET BOX (B) ADAPTER NOT ALLOWED IN CANADA GROUNDING MEANS Figure 1 Grounding Methods -3-

CONTROLS/OPERATION Your fireplace has the following functions: On/Off I / O Power to the unit Low heat II 700 watts Note: For a high level of heat press II and III High heat III 1350 watts FOR YOUR

5 CONTROLS/OPERATION Your fireplace has the following functions: On/Off I / O Power to the unit Low heat II 700 watts Note: For a high level of heat press II and III High heat III 1350 watts FOR YOUR SAFETY Repairs must be performed by a qualified person. REPLACING THE LIGHT BULBS This fireplace uses 1 clear 110 Volt, 40 Watt, E-12 socket base light bulbs (small base, chandelier candle type bulb). The access plate is located on the back of the unit. For convenience, if one of the light bulbs burns out, it may be easier to replace both of the light bulbs at the same time. WARNING: Do not exceed 40 Watts per bulb. Use of higher a rated bulb may result in a fire, causing property damage, personal injury or loss of life. BULB COVER IN OUT BULB FIG 1 FIG 2 BACK IN OUT 1. Turn off the power to the unit, and unplug it from the electrical outlet. 2. Let the fireplace cool if it has been operating. 3. Turn the fireplace so you are facing the back of the fireplace. 4. Look for the access plate with the gold printing on it. 5. Remove the 2 screws holding the access plate in position (FIG1). Once you have removed the 2 screws, lift the access plate so the 2 positioning tabs come free of their slots. Once you have removed the access plate you can see and access the 40 watt chandelier bulb (FIG 2). -4-

6 6. Remove each light bulb by unscrewing them out of the bases, turning them counterclockwise. You can use one hand to hold the light socket in place, if required. 7. Install the new light bulbs by turning each light bulb into the base clockwise. You can use one hand to hold the light socket in place, if required. 8. Replace the access plate by inserting the tabs, pushing the plate up against the fireplace back, and inserting the 2 screws. 9. Turn the fireplace back so you are facing the front of the fireplace. 10. Plug the fireplace back into the electrical outlet and turn the power on and enjoy the flame effect. CLEANING Turn heater OFF and unplug from outlet. Use a vacuum or duster to keep heat and vent area clean from dust and dirt. The exterior of the fireplace should be cleaned with a damp cloth or duster. Do not use abrasive cleaners, liquid sprays, or any other cleaner that may scratch the surface. -5-

. IMPORTANT For questions, concerns or problems with our product please email our customer service department: parts@jrhome.com or call 1-800-561-5550.

7 . IMPORTANT For questions, concerns or problems with our product please our customer service department: or call DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE. WARRANTY This product is inspected, tested and carefully packaged to minimize the chance of damage during shipment. If a part (excluding light bulbs and fuses*) within one year from the date of purchase proves to be defective in material or fabrication under normal use, the part will be repaired or replaced. The Company s obligation under the warranty is to replace or repair defective parts at our discretion. Any expenses or damage resulting from the installation, removal or transportation of the product will be the responsibility of the owner and are not covered by this warranty. The owner assumes all other risks arising from the use or misuse of the product. The warranty will be void if the product damage or failure is deemed by the Company to be caused by accident, alteration, misuse, abuse, incorrect installation or removal, or connection to an incorrect power source by the owner. The Company neither assumes, nor authorizes any person or entity to assume for it any obligation or liability associated with its products. Light bulbs and fuses are not covered under this warranty. If you have any questions regarding the warranty or service, please call our toll free number: Customer Service JR Home Products Unit Riverbend Drive, Burnaby BC, V3N 0C1 Toll Free: parts@jrhome.com Registration can be completed online at or by mailing this form. Warranty Registration Information Form / Formulaire d enregistrement de la garantie Name / Nom: Street / Adress: City / Ville: Province / Province: Postal Code / Code postal: Daytime Phone # / No téléphone jour: Evening Phone # / No téléphone soir: Address / Courriel: You MUST register your product to receive warranty service. Product/Produit: Place of Purchase / Lieu de l achat: Date of Purchase / Date de l achat: Model # / No de modèle: Serial # / Numéro de série: You MUST register your product to receive warranty service. For warranty service, contact J&R Home Products at the address, phone numbers listed below within 30 days of purchase. Be sure to have your sales receipt and original date of purchase. All warranty service will be coordinated by J&R Home Products service center. Vous DEVEZ enregistrer votre produit pour vous prévaloir de la garantie. Afin de faire valoir la garantie, communiquez avec J&R Home Products à l adresse et aux numéros indiqués ci-dessous dans les 30 jours suivant la date d achat. Ayez en main votre reçu et la date d achat. Toutes les demandes liées aux garanties seront traitées par le centre de service de J&R Home Products. Please mail to / Veuillez poster le tout à : Parts & Service Department, J&R Home Products Ltd. Unit Riverbend Drive, Burnaby BC, V3N 0C

Jetson Mini Stove. Owner s Manual. Item number: ES-312 Model Number: FX3

Jetson Mini Stove. Owner s Manual. Item number: ES-312 Model Number: FX3 Jetson Mini Stove Owner s Manual Item number: ES-312 Model Number: FX3 Crystals may become loose in shipping. This will not affect the function of the heater. READ & SAVE THESE INSTRUCTIONS Carefully read