InVue Installation Instructions

Transcription

1 InVue Installation Instructions Rev

2 Introduction This document contains step-by-step instructions for installing our products and securing your merchandise. Please contact InVue Security Products at with additional questions about your security system. Table of Contents List of InVue Parts Smart Store...3 List of InVue Parts Bridge Store...7 List of InVue Parts HS Part Identification...12 IR2 Key Setup...13 Series 2000 Puck & Custom Wedge Installation...14 Series 2000 Puck & Sensor Clamp Installation...16 Series 2000 Handheld Installation...19 Series 2000 Nokia Tablet Installation...20 Series 2000 Apple Tablet Installation...21 Series 2000 Tablet Installation (using MP014)...22 Bridge: Wall Mount Installation...23 Bridge: Droid Installation...27 Bridge: Apple Tablet Installation...29 Removing Sensor from Merchandise...32 Zips! Installation...33 Cam Lock Installation...35 HS100 Installation...37 Online Assistance...47 Frequently Asked Questions...48 IR2 Key Lights...49 Best Practices

3 List of InVue Parts Smart Store SERIES 2000 SERIES 2000 MP416-W Exposed HH Micro USB Sensor, short white MP407-W Exposed HH Apple 30 pin Sensor, short white MP417-W Exposed HH Apple Lightening Sensor, short white MP408-W Camera Sensor white MP418-W Exposed HH Samsung Sensor white MP200-W Handheld IR Puck white MP419-W Exposed Tablet HHE Sensor w/ Power Port white MP208-W* Camera IR Puck white *Image shown in black for reference only. Product will ship in white. MP420-W Exposed Alarm Only HH with Plunger white MP100-W Handheld Alarm Unit white MP014-W Tablet Medallion Only white MP229-W Custom Handheld Wedge white 3

4 List of InVue Parts Smart Store IR2 Key SYSTEM PK4400-S IR2 Sounder Key POWER CONNECTOR & POWER SUPPLY PS18VUS 18 Volt Power Supply PK4491 Key Retractor EC Volt Power Supply (For Series 940) PK4401 IR2 Programming Station TC722 Lightning Power Connector PK4404 IR2 Charger HC71164 Micro USB Power Connector PS5VMU-US 5V Power Supply (for PK4401) PS18VB2-US 18V Power Supply (for PK4404) 4

5 List of InVue Parts Smart Store 1 PORT POD ZIPS! SMART LOCK EC9455-W 1 Port POD with IR Extender white EM3201-W Zips! 100 Single Sensor white PL301-W Cam Lock white EC9195-W Micro Sensor with Medallion white EM3202-W Zips! 100 Dual Sensor white PL Cam Lock Arm EM3207-W Zips! 100 Single Sensor white AF6323 Cam Lock Eye Cover EM3207W-XL Zips! 100 Single Sensor white (250 mm) 5

6 List of InVue Parts Smart Store ADHESIVES ADHESIVES Tools ADH1000 Replacement Adhesive for HH IR Puck Round 10 pack EM3400 Swivel Mount Adhesive for Zips 100 Module 6 pack AF6303 Adhesive Removal Tool ADH1001 Replacement Adhesive for Camera IR Puck 20 pack EM3401 Adhesive for Zips Single and Dual Sensors 6 pack AF6313 Multi Tool ADH1003 Crescent Replacement Adhesive 24 pack ADH1007 Verizon Riser Adhesive MP254 Series 2000 Removal Tool ADH2001 Replacement Adhesive for Medallion 20 pack ADH2009 Medium Round Split Adhesive with Hole HC7429 Battery Cover Support Adhesives HC7430 Smartphone Clear Adhesive 5 pack 6

7 List of InVue Parts Bridge Store SERIES 2000 SERIES 2000 MP416-W Exposed HH Micro USB Sensor, short white MP200-W Handheld IR Puck white MP417-W Exposed HH Apple Lightening Sensor, short white MP208-W* Camera IR Puck white *Image shown in black for reference only. Product will ship in white. MP418-W Exposed HH Samsung Sensor white MP100-W Handheld Alarm Unit white MP419-W Exposed Tablet HHE Sensor w/ Power Port white MP229-W Custom Handheld Wedge white MP420-W Exposed Alarm Only HH with Plunger white MP Degree Clear Wedge MP014-W Tablet Medallion Only white MP238 Custom Verizon Spacer 7

8 List of InVue Parts Bridge Store IR2 Key SYSTEM PK4400-S IR2 Sounder Key POWER CONNECTOR & POWER SUPPLY PS18VUS 18 Volt Power Supply PK4491 Key Retractor EC Volt Power Supply (For Series 940) PK4401 IR2 Programming Station AF Position Power Strip PK4404 IR2 Charger TC722 Lightning Power Connector PS5VMU-US 5V Power Supply (for PK4401) HC71164 Micro USB Power Connector PS18VB2-US 18V Power Supply (for PK4404) 8

9 List of InVue Parts Bridge Store 1 PORT POD ADHESIVES ADHESIVES EC9455-W 1 Port POD with IR Extender white ADH1000 Replacement Adhesive for HH IR Puck Round 10 pack EM3400 Swivel Mount Adhesive for Zips 100 Module 6 pack EC9412-W LP Sensor Hybrid Cable white ADH1001 Replacement Adhesive for Camera IR Puck 20 pack EM3401 Adhesive for Zips Single and Dual Sensors 6 pack ADH1003 Crescent Replacement Adhesive 24 pack ADH1004 Display Wedge Replacement Adhesive ZIPS! EM3207-W Zips! 100 Single Sensor white ADH2001 Replacement Adhesive for Medallion 20 pack EM3207W-XL Zips! 100 Single Sensor white (250 mm) HC7429 Battery Cover Support Adhesives HC7430 Smartphone Clear Adhesive 5 pack 9

10 List of InVue Parts Bridge Store Tools AF6303 Adhesive Removal Tool AF6313 Multi Tool MP254 Series 2000 Removal Tool 10

11 List of InVue Parts HS100 HS100 HS100 HS100 Alarm Unit AF6320 T-8 Bit (for lock down feature) HS110-W Handheld Puck white ADH2022 Handheld Sensor Replacement Adhesive (for HS144) HS144-W Apple Lightning Angled Handheld Sensor white HS126 Installation Tool (2 pack) HS146-W Micro USB Angled Handheld Sensor white HS mm - 19 mm Bugle HS191-W Hole Adapter Plug (45 mm) white PS513-US 5.3 Volt USB Power Supply 11

12 Part Identification AP Sensor The charging plug on the sensor is also the source of the alarm. If your customer pulls out this plug, the alarm will sound. Gold is Good! Solid gold light = System is armed Blinking gold light = Alarming 12

13 IR2 Key Setup Plug power supply into Programming Station. Confirm the GREEN LED light on the Programming Station. Plug power supply into Charger. Confirm the GREEN LED light on the Charger. Fully charge IR2 key in charger. The keys will charge in 2 hours and GREEN LED light on key will light up when charged. After key has been charged, RED light will show up in circle, indicating key must be place in Programming Station. 5 Place key into Programming Station and press and hold the button until you hear a beep to confirm that key has been activated. 6 Full blue circle = Fully charged, 12 hours of activation. These keys will turn off your alarms; activate them every morning. 13

14 Series 2000 Puck & Custom Wedge Installation 1 Wipe the top of the wedge 2 Slide the puck (MP200) 3 Remove the dear film from 4 (MP229) and the top of the display counter with the alcohol wipe provided. Let it dry completely. cord down the short side of the wedge. the puck (MP200) and place the puck on the wedge. Align the InVue logo with the notch on the wedge. Press both parts firmly for at least 10 seconds. 5 Slide the puck cord through 6 Remove the dear film from 7 Tuck the puck cord into the 8 the top of the display counter. the wedge (MP229). groove on the wedge. Place the wedge close to the slot in the fixture. Press firmly for at least 10 seconds. 14

15 Series 2000 Puck & Custom Wedge Installation 9 Plug the puck (MP200) cord 10 Remove the clear film from into the alarm unit. the alarm unit. 11 Firmly press puck onto fixture 12 for at least 10 seconds. Plug cable from alarm unit into 18 volt power supply (PS18VUS) and into outlet. 15

16 Series 2000 Puck & Sensor Clamp Installation 1 Wipe the bottom of the 2 Place the adhesive 3 Place the adhesive (ADH1007) 4 bracket (MP272) and the fixture with the alcohol wipe provided. Let it dry completely. (ADH1007) onto the bottom of the bracket as illustrated. onto the bottom of the puck as illustrated. Remove the clear film from the adhesive on the bracket (MP272) and firmly press onto the wedge. Confirm groove in bracket lines up with groove in wedge. 5 Remove clear film off all 3 6 Slide the puck onto the 7 Wipe the back of the 8 adhesives on the bottom of the puck. bracket with the cord towards the groove in the bracket. merchandise with the alcohol wipe provided. Let it dry completely. Plug the power connector into the merchandise. 16

17 Series 2000 Puck & Sensor Clamp Installation 9 Remove the clear film from the adhesive. 10 Center sensor onto back of merchandise. Press firmly for at least 10 seconds. 11 Firmly plug the sensor into 12 the puck. Place sensor onto puck. Slide sensor clamp through bracket and sensor as illustrated. 13 Confirm sensor clamp does 14 Slide the other sensor 15 Tighten sensor clamp with 16 Remove the film from the not interfere with any buttons on merchandise. clamp through the bracket and sensor. T-8 bit. clear adhesive on the wedge. 17

18 Series 2000 Puck & Sensor Clamp Installation 17 Slide the cord through the fixture. Tuck the puck cord into the groove on the wedge. 18 Press firmly onto fixture for at least 10 seconds. 19 Plug the puck cord into the alarm unit. 18

19 Series 2000 Handheld Installation 1 Wipe the back of the 2 Plug the power connector 3 Remove the clear film 4 merchandise with the alcohol wipe provided. Let it dry completely. into the merchandise. If the sensor cord needs to be rerouted continue to step 4. from the medallion. Center and press sensor onto merchandise. Press firmly for at least 10 seconds. Open the medallion with a screwdriver. Top of Phone 5 Open the medallion and 6 Make sure the strain relief is 7 Plug the sensor into the puck 8 reroute the sensor cable so the cord end comes out to the top of the phone. tucked into the medallion. and place the sensor onto the puck. Place the key on the IR lens on the puck and press the button once on the key to disarm alarm. 19

20 Series 2000 Nokia Tablet Installation Bottom of Merchandise 1 Wipe the back of the 2 Plug the power connector 3 Remove the clear film from 4 merchandise with the alcohol wipe provided. Let it dry completely. into the sensor. the adhesive. Center the sensor on the back of the merchandise. Confirm power connector is towards the bottom of the merchandise. 5 Plug power connector into the merchandise. 20

21 Series 2000 Apple Tablet Installation 1 Wipe the back of the 2 Plug the power connector into 3 Plug the power connector into 4 merchandise with the alcohol wipe provided. Let it dry completely. the sensor and remove the clear film from the adhesive. the merchandise. Place the sensor onto the merchandise with the cord towards the top of the merchandise. 21

22 Series 2000 Tablet Installation (Must use MP014) 1 Use the multi tool to open the 2 Remove the sensor cord from 3 Wipe the back of the tablet 4 sensor. the medallion. with the alcohol wipe provided. Let it dry completely. Plug the sensor into the tablet. 5 Remove the clear film from the medallion (MP014). 7 Center and place the 8 Route cable through sensor 9 medallion as illustrated above. Confirm the sensor cord will be able to come out the top of the medallion. Press the medallion firmly for at least 10 seconds. as illustrated above. Make sure the strain relief is tucked into the medallion. Close the medallion and tighten screw with multi tool. 22

23 Bridge: Wall Mount Installation 1 Remove the ring on the clear tube (MP238). 2 Wipe the wedge and clear tube with the alcohol wipe provided. Let it dry completely. 3 Remove the clear film from the adhesives on the bottom of the handheld IR puck. 4 Attach the puck onto the wedge with the cord coming out the short end of the wedge. Press firmly for at least 10 seconds. 5 Remove the film on the adhesive on the bottom of the wedge. 6 Attach the wedge onto the clear tube. Confirm the puck cord is tucked into the groove of the clear tube. 7 Wipe the front of the fixture with the alcohol wipe provided. Let it dry completely. 8 Slide puck cord and assembly through the fixture. 23

24 Bridge: Wall Mount Installation 9 Confirm puck cord is at the 10 Slide cord through the plastic 11 Tighten the wingnut around 12 top of the fixture. nut. Be sure that flat side of the nut is against the surface of fixture. the clear tube. Plug the puck cord into the alarm unit behind wall. 13 Plug the power supply into 14 Wipe the back of the 15 Remove both clear films from 16 the alarm unit auxiliary cord. fixture with the alcohol wipe provided. Let it dry completely. the alarm unit. Press alarm unit firmly against surface of fixture directly underneath the tube mount and nut assembly. 24

25 Bridge: Wall Mount Installation 17 Plug power supply into power strip. 18 Wipe back of merchandise with alcohol wipe provided. Let it dry completely. 19 Use the multi tool to open sensor. 20 Pull the sensor components apart. 21 Plug the power connector into the merchandise. 22 Remove clear film from adhesive. 23 Place the sensor onto back of 24 merchandise as it appears in the image above. Press firmly for at least 10 seconds. Route cable through sensor. Make sure the strain relief is tucked into the medallion. 25

26 Bridge: Wall Mount Installation 25 Close the sensor and tighten 26 Plug sensor into puck. screw with multi tool. 27 Final assembly should 28 resemble image above. To disarm the alarm, use the IR2 Key. 26

27 Bridge: Droid Installation 1 Wipe the top of the fixture and wedge with the alcohol wipe provided. Let it dry completely. 2 Remove the clear film from the adhesives on the bottom of the puck. 3 Attach the puck onto the wedge with the cord coming out the short end of the wedge. Press firmly for at least 10 seconds. 4 Remove the film on the adhesive on the bottom of the wedge. 5 Push the cord all the way through the groove in the wedge. Press wedge firmly onto fixture for at least 10 seconds. 6 Slide cord through the slot in the fixture directly behind the IR puck. 7 Below the fixture: Plug the puck cord into the alarm unit below the counter. 8 Plug the power supply into the alarm unit auxiliary cord and into the outlet. 27

28 Bridge: Droid Installation 9 Wipe the bottom of the 10 Press alarm unit firmly on a 11 Plug power supply into power 12 fixture with the alcohol wipe provided. Let it dry completely. Remove both clear films from the alarm unit. solid surface below counter for at least 10 seconds. Do not install over holes or openings to ensure plunger is depressed. strip. Wipe back of merchandise with alcohol wipe provided. Let it dry completely. 13 Plug the sensor into the merchandise. Center the sensor onto the back of the merchandise and press firmly for at least 10 seconds. 14 Plug the sensor into the puck. 15 Final assembly should 16 resemble image above. To disarm the alarm, use the IR2 Key. 28

29 Bridge: Apple Tablet Installation 1 Remove or lift glass topper 2 Wipe back of clear tube 3 Remove the clear film from 4 from fixture and insert tube mount in the hole in the fixture. with alcohol wipe provided. Let it dry completely. the adhesives on the bottom of the puck. Attach the puck onto the wedge with the cord coming out the short end of the wedge. Press firmly for at least 10 seconds. 5 Slide the cord through the hole in the clear tube. 6 Remove the film on the ad- 7 Press wedge firmly onto the 8 hesive on the bottom of the wedge. clear tube for at least 10 seconds. Slide IR puck cord through plastic nut. Be sure flat side of the nut is against the inside surface of the fixture. 29

30 Bridge: Apple Tablet Installation 9 Tighten the wingnut around 10 Wipe the inside of the 11 Plug the puck cord into 12 the clear tube. fixture with the alcohol wipe provided. Let it dry completely. the alarm unit below the counter. Remove both clear films from the alarm unit. 13 Press alarm unit firmly below counter for at least 10 seconds. 14 Plug the power supply into 15 Plug power supply into power 16 the alarm unit auxiliary cord. strip. Wipe the back of the merchandise with the alcohol wipe provided. Let it dry completely. 30

31 Bridge: Apple Tablet Installation 17 Plug the power connector into 18 Plug the power connector into 19 Place the sensor onto the 20 the sensor and remove the clear film from the adhesive. the merchandise. merchandise with the cord towards the top of the merchandise. Plug the sensor into the puck. 21 Final assembly should resemble image above. 22 To disarm the alarm, use the IR2 Key. 31

32 Removing Sensor from Merchandise 1 To remove the sensor from 2 Unplug the sensor from the 3 Unscrew the black cap on the 4 the merchandise, first turn off the alarm with your IR key. puck. multi tool to access all the bits. Find the removal tool bit (flat bar). Insert the removal tool bit into the multi tool. 5 Unplug power connector from 6 Slide removal tool into sensor. 7 the merchandise. Twist to remove. Revmoe the old adhesivesand replace it with a new adhesive. Always replace adhesive(s) before reusing your InVue sensors. 32

33 Zips! Installation 1 Wipe the fixture with the 2 Remove the clear film from 3 Remove the white tab to 4 alcohol wipe provided. Let it dry completely. the adhesive. activate the battery. Press Zip firmly onto fixture. Press for at least 10 seconds. 5 Slide the sensor through the 6 Remove the clear film from 7 Slide the sensor through the 8 box. the box. box. Wipe the merchandise with the alcohol wipe provided. Let it dry completely. 33

34 Zips! Installation 9 Remove the clear film from 10 the sensor. Press sensor firmly onto merchandise. Press for at least 10 seconds. 34

35 Cam Lock Installation 1 Remove screws and metal plate inside drawer. 2 Insert Cam Lock into recess opening in door. Be sure to test Cam with programmed IR Key and make sure lens shows locked position (solid black eye). 3 Make sure lock is inserted in 4 correct direction by checking alignment of IR lens in hole from front. Observe IR lens to confirm LOCKED as shown above. Place metal plate over Cam Lock. in place. around Cam barrel. 5 Tighten screws holding plate 6 Place anti-rotation washer 7 Thread Cam Lock nut on bar- 8 rel and tighten. Bend all 3 prongs on antirotation washer over nut. 35

36 Cam Lock Installation 9 Place Cam arm on barrel. Be 10 Photo indicates arm position 11 sure to orientate the Cam arm to the LOCKED position, this is straight up. Hand tighten arm on barrel with a screwdriver. DO NOT USE POWER TOOLS! for LOCKED Cam Lock. Photo indicates arm position for UNLOCKED Cam Lock. Test lock before closing drawer. L-BRACKET ADJUSTMENT 1 Loosen screws. Slide L- 2 Tighten screws to secure L- 3 Bracket forward or backward so Cam arm is 1/8 or less away from metal leg when in locked position. Bracket. Test lock to ensure it operates correctly. If Cam arm hits L-Bracket and cannot fully swing behind metal leg, use key to unlock and pull drawer and adjust L-Bracket as needed. DO NOT manually move Cam arm. 36

37 HS100 Installation Bridge 1 Wipe the fixture (above 2 Slide hole adapter plug 3 Remove the clear film from 4 and below fixture) with the alcohol wipe provided. Let it dry completely. (HS191) into the fixture. the adhesive on the bottom of the puck (HS110). Slide ribbon cable through hole. 5a Fit puck into adapter plug. 5b Press firmly for at least 10 6 Locate the install kit 7 Confirm IR lens is facing towards front of fixture. seconds. (HS120). You will need the yellow tool and bugle C. Place the bugle C into the puck. 37

38 HS100 Installation Bridge 8 Below Counter: Remove the adhseive cover on the ribbon cable. 9 Lay the ribbon cable flat and avoid covering the bugle. Press ribbon cable to adhere adhesive onto fixture. 10 Remove white tab to activate battery and remove clear film from both adhesives on alarm unit (HS100). 11 Plug ribbon cable into alarm unit. 12 Align hole in alarm unit with bugle. Press firmly for at least 10 seconds. 13 Using tool, tighten bulge onto alarm unit. 14 Pull the gate open on the alarm unit. Use T-8 bit to loosen screw to hold open gate. 15 Slide sensor (HS144) cable through bugle. IMPORTANT! Follow next steps in order or cable will not fit through bugle. 38

39 HS100 Installation Bridge 16 Confirm ball stays out of the 17 Pull the shortest cable 18 Pull the USB cord through 19 bugle for the next steps. through first. next. Slide the ball through last. 20 Use T-8 bit to screw in the 21 Plug cords into alarm unit as 22 Plug USB into OEM and into 23 screw to close gate. illustrated above. outlet. Use T-20 bit to loosen arms on sensor. 39

40 HS100 Installation Bridge 24 Remove both arms from 25 Wipe back of phone with 26 Remove the clear film from 27 sensor. alcohol wipe provided. Let it dry completely. the adhesive on the sensor. Center phone onto sensor and press firmly for at least 10 seconds. LOCK 28 Slide arms into sensor and 29 Use T-20 bit to lock arms into 30 Use T-20 bit to tighten arms 31 onto phone. Confirm arms sit flush against phone. If arms do not sit flush against phone, switch arms. sensor. around phone. Confirm arms do not interfere with any buttons on the phone. Important! Use T-8 bit to lock sensor into puck. Final assembly should resemble image above. 40

41 HS100 Installation Smart Stores 1 Wipe the fixture with the 2 Wipe hole adapter with the 3 Remove the clear film from 4 alcohol wipe provided. Let it dry completely. alcohol wipe provided. Let it dry completely. the adhesive on the bottom of the puck (HS110). Slide ribbon cable through hole adapter with adhesive on adapter facing away from puck.. 5 Press puck and adapter 6 Remove the clear film from 7 Slide ribbon cable through 8 together firmly for at least 10 seconds. the adhesive on the bottom of the adapter. top of fixture. Press firmly onto fixture for at least 10 seconds. Confirm IR lens is facing towards front of fixture. 41

42 HS100 Installation Smart Stores X 9 Slide bugle through puck. 10 Confirm bugle sit flush into puck. 11 A: Confirm bristles are out of the way of bugle below counter. 11 B: Incorrect installation. Move bristles out of the way of bugle. 12 Slide ribbon cable through opening in plate. 13 Slide bugle through hole in plate and confirm screws are facing down. 14 A: Hold puck above counter. B: And tighten nut below counter

43 HS100 Installation Smart Stores 15 Remove white tab to activate battery from alarm unit (HS100). Wipe alarm unit with alcohol wipe provided. Let it dry completely. 16 Remove the clear film from the adhesive on the mounting plate. 17 A: Place alarm unit into mounting plate with opening in alarm unit aligning with hold in bracket. 17 B: Press firmly for at least 10 seconds. 18 Plug ribbon cable into alarm unit. 19 Slide mounting bracket through screws. 20 Tighten both wingnuts onto screws. 21 Pull the gate open on the alarm unit. Use T-8 bit to loosen screw to hold open gate. 43

44 HS100 Installation Smart Stores 22 Slide sensor (HS144) cable 23 Confirm ball stays out of the 24 Pull the shortest cable 25 through bugle. IMPORTANT! Follow next steps in order or cable will not fit through bugle. bugle for the next steps. through first. Pull the USB cord through next. 26 Slide the ball through last. 27 Use T-8 bit to screw in the 28 Plug cords into alarm unit as 29 screw to close gate. illustrated above. Plug USB into OEM and into outlet. 44

45 HS100 Installation Smart Stores 30 Use T-20 bit to loosen arms 31 Remove both arms from 32 Wipe back of phone with 33 on sensor. sensor. alcohol wipe provided. Let it dry completely. Remove the clear film from the adhesive on the sensor. 34 Center phone onto sensor 35 Slide arms into sensor and 36 Use T-20 bit to lock arms into 37 and press firmly for at least 10 seconds. onto phone. Confirm arms sit flush against phone. If arms do not sit flush against phone, switch arms. sensor. Use T-20 bit to tighten arms around phone. Confirm arms do not interfere with any buttons on the phone. 45

46 HS100 Installation Smart Stores LOCK 38 Important! Use T-8 bit to lock sensor into puck. Final assembly should resemble image above. 46

47 Online Assistance 1 Login Example Log In: SW_BSMITH Password: bill Choose location or search by store number. 3 Choosing your type of store will automatically fill in the exact InVue products belonging in your store. You can also search by item number or description (name it), then proceed with the order. 4 You can also retrieve order information such as tracking numbers or copy of invoice by clicking on order/shipment inquires at bottom left. 47

48 Frequently Asked Questions Q. How does the IR2 Key work? A. The IR2 Programming Station activates the IR2 Key: An activated key can be used for up to 12 hours (Fig. 4). Charging will de-activate the key (Fig. 1). When you remove the key from the charger you will get a red circle in the key (Fig. 2), the key will need to be re-activated on the Programming Station before use (Fig. 3). Q. How do I re-activate my IR2 Key? A. Re-activate your IR2 Key on the Programming Station (Fig. 3). Place the IR2 Key directly onto the IR Lens on the Programming Station and press the black button. You cannot do this from a distance. If the IR2 Key is re-activated properly, the BLUE light on the IR2 Key will light up (Fig. 4). Q. How do I know if my IR2 Key is working? A. Press the black button once on the IR2 Key, the BLUE light on the IR2 Key will light up (Fig. 4). If you get a red light, the key is inactive or you are trying to program the key on the wrong Programming Station (Fig. 2). FIG. 1 FIG. 2 FIG. 3 FIG. 4 48

49 IR2-S Key Lights BATTERY INDICATOR LIGHTS (When key is in charger) BATTERY INDICATOR LIGHTS (When key is out of charger) ACTIVATION LIGHTS (When key is out of charger) Note: If battery is good, battery indicator will normally be off. It will only show green for several seconds when button is pressed. Flashing RED = Charging GREEN = Battery Good (continue use) ACTIVATION LIGHTS All BLUE light = Up to 12 hours of activation left 3/4 BLUE light = Up to 9 hours of activation left Solid GREEN = Fully Charged Flashing ORANGE = Battery Low (return to charger soon) 1/2 BLUE light = Up to 6 hours of activation left 1/4 BLUE light = Up to 3 hours of activation left Flashing RED = Battery Too Low For Use (return to charger immediately) All RED light = Deactivated (return to programming station) 49

50 IR2-S Key Lights BINET OPERATION OPERATION tion CABINET IR2-S Key* against lock, push button and wait for INET OPERATION CABINET OPERATION ep before removing key. CABINET OPERATION Position IR2-S Key* against lock, push button and wait for on IR2-S Position Key* against IR2-SKey* Key* lock, against push button lock, push and wait button for and wait for beep before key. (Position IR2-Sremoving against lock, push button and wait p before beep before key. removing key. forremoving beep before removing key.) IR2-S KEY To OPERATION stop reminder beep or buzz (3 options): To stopreminder reminder To beep stop beep reminder or buzz (3 options): or buzz (3 options): To stop or buzz (3 beep options): 1) Close and lock cabinet with IR2-S Key. 1) Close and lock cabinet with 1) lock Close andand locklock cabinet withwith 1) Close and 1) Close cabinet cabinet IR2-S Key. with IR2-S Key. IR2-S Key. IR2-S Key. *IR2-S Key must be charged and activated. *IR2-S Key must be See IR2 Key instruction guide. *IR2-S Key must chargedsee and activated. charged and be activated. *IR2-S Key must bekey charged Key must and beactivated. charged See*IR2-S IR2 Key instruction guide. and activated. IR2 instruction guide. See IR2 Key instruction See IR2 Key guide. instruction guide. EP EP IR2-S KEY OPERATION IR2-S KEY OPERATION To stop reminder beep or buzz (3 options): IR2-S KEYIR2-S OPERATION KEY OPERATION BEEP BEEP Alert Mode Once cabinet is unlocked the IR2-S Key will Alertand Mode light up purple beep AlertMode Mode until cabinet is Alert ModeOnce Alert cabinet is unlocked the IR2-S Key will relocked. Once cabinet is unlocked the Once cabinet isonce unlocked cabinet the isir2-s unlocked Key the willcabinet IR2-S Key light up purple and beep until is will IR2-S Key will light up purple light up Key purple light and up beep cabinet beep Note: cannot be purple useduntil toand unlock a is until cabinet is relocked. and beep until cabinet is relocked. relocked. second cabinet when beeping, but can relocked. Note: operate PODs inkey alertcannot mode.be used to unlock a Note: Keycannot cannot beused Note: Key cannot Note: becabinet Key used towhen unlock be ausedtotounlock a second beeping, but can unlock a second cabinet second cabinet second when beeping, cabinet when but beeping, can when but can operate PODs in alert mode. butincan operate PODs operate in beeping, alert mode. PODs alertoperate mode. PODs in alert mode. 2) Wait 120 seconds. Return key to unlocked cabinet to reactivate key. 2) Wait Return 120 seconds. Return 2) Wait 120 seconds. key to unlocked key to unlocked to 2) Wait 120 seconds. 2) Wait Return 120 seconds. key to key. unlocked Returncabinet key to unlocked cabinet to reactivate reactivate key. cabinet to reactivate cabinetkey. to reactivate key. Locked Locked Locked Locked Locked 3) Return key to charger or programming station. 3) Return key to charger or Return key to charger or or 3) Return to 3) charger Return key or to charger Note:key If3)returned to charger, programming station. programming station. programming programming key must be station. reactivated on station. Note: If returned to charger, Note: Ifstation returned to charger, programming before Note: If returned Note: tobecharger, Ifreactivated returned toon charger, key must be reactivated on key must use. key mustprogramming beprogramming reactivated key must be on reactivated station before station beforeon programming station programming before station before use.use. use. use. Error If an error occurs, IR2-S Key will flash and Error buzz untilerror error is corrected. Ensure panels Error Error If an error occurs, IR2-S If an occurs, are fully closed error and try again.ir2-s Key will flash and will error flash and buzz If an error occurs, IfKey anir2-s error Key occurs, will flash IR2-S and KeyEnsure will flash and buzz until is corrected. panels until error corrected. En- Ensure panels buzz until are error buzz is corrected. until is error Ensure is corrected. panels fully closed and try again. sure panels fully are fully closedare and fully try closed again.are and tryclosed again. and try again

51 Best Practices For Optimal Security Display 1. ALWAYS replace the adhesive when re-merchandising. 2. ALWAYS wipe the display counter/fixture and merchandise with an alcohol wipe. Let the alcohol dry completely before placing any pucks onto the display counter/fixture. Let the alcohol dry completely before placing any merchandise onto the sensors. 3. Charge your IR2 Key EVERYDAY! 51