Code Alert Series 30 Software User Guide

Size: px
Start display at page:

Download "Code Alert Series 30 Software User Guide"

Transcription

1 Code Alert Series 30 Software User Guide

2 2018 RF Technologies, Inc. All specifications subject to change without notice. All Rights Reserved. No Part of this work may be reproduced or copied in any form or by any means without written permission from RF Technologies, Inc. and indicate trademarks owned by RF Technologies, Inc.

3 Contents CONTENTS CONTENTS... 1 OVERVIEW... 5 Introduction... 5 Login... 5 Web Browser... 5 Desktop... 6 Server Name... 7 Using the System... 7 Help... 8 DESKTOP CLIENT... 9 Residents Page... 9 Add Residents Modify Resident Information Change Mobile Device(s) Change Site Status Transfer Remove Residents Resident Reports MOBILE CLIENT Residents Page Add Residents Modify Resident Information Change Mobile Device(s) Change Site Status Transfer Remove Residents ALERTS Alerts Code Alert Series 30 Software User Guide Page 1 of 52

4 Contents Claim Flashing Red Alerts Priority Alert Priority Assist Priority High Temp Priority Low Temp Priority Open Priority Out of Bed Priority Out of Chair Priority Smoke How To Red Alerts Alert Assistance Required Check Bathroom Check Resident Depleted Battery Door Alarm High Temperature Loiter Low Temperature Open Reported Out of Bed Out of Chair Smoke Reconnecting System Down System is Down How To Yellow Alerts Communication Failure Low Battery Page 2 of 52 Code Alert Series 30 Software User Guide

5 Contents On Battery Power RF Interference Tamper How To Quick Look Display REVISION HISTORY Code Alert Series 30 Software User Guide Page 3 of 52

6 Contents This page intentionally left blank. Page 4 of 52 Code Alert Series 30 Software User Guide

7 Overview OVERVIEW Introduction The CODE ALERT Software Series 30 System is a web based application and is designed to provide a reliable and easy-touse nurse call and wander management system for Independent and Assisted Living facilities. NOTE: Prior to using the system, ensure that your system administrator has configured rooms and mobile devices (wander transmitters and pendants) within the system. If they are not, please contact your system administrator to configure these before proceeding. NOTE: If when opening the application, you are prompted that the site cannot be accessed or the site is unsecure, please contact your system administrator to properly configure the certificate on your workstation. Login Web Browser Typically you will login to the Code Alert software via a Favorite/Bookmark on your web browser, but you can also access it directly through your desktop or by using the server name. 1. Open your Web Browser 2. Click the Code Alert Software favorites 3. Click Login in the upper right-hand corner Code Alert Series 30 Software User Guide Page 5 of 52

8 Overview 4. Enter your Username and Password (NOTE: this information is case sensitive) 5. Press Enter or click the Login button 6. The Client application opens Desktop 1. On your desktop, double click the client application icon 2. Click Login in the upper right-hand corner 3. Enter your Username and Password (NOTE: this information is case sensitive) 4. Press Enter or click the Login button 5. The Client application opens Page 6 of 52 Code Alert Series 30 Software User Guide

9 Overview Server Name 1. Open your Web Browser 2. Enter the server name /Client 3. Enter your Username and Password (NOTE: this information is case sensitive) 4. Press Enter or click the Login button 5. The Client application opens Using the System Once the client application is open, the icon for the tab (Alarms or Residents) you are currently on will display as dark blue while the other will display as a light blue color. NOTE: The system will automatically log off after 5 minutes of inactivity. Code Alert Series 30 Software User Guide Page 7 of 52

10 Overview Help Help can be obtained a few different ways within the system: Hovering or mouse over a menu option will display the title for that particular menu option Clicking the Help link at the bottom of the page will open the Help menu From there, you can click the links to open the User Guide and the Administrator Guide Page 8 of 52 Code Alert Series 30 Software User Guide

11 Desktop Client DESKTOP CLIENT Residents Page The Residents page allows you to add, update, and remove residents from the system, change their status, view individual resident activity reports, as well as add new pendants to the system. Resident information is divided into three (3) categories: Basic Information resident name Facility Information resident unit/room assignment and check-in schedule Mobile Devices pendants, wander transmitters, and/or chair sensors assigned to the resident Code Alert Series 30 Software User Guide Page 9 of 52

12 Desktop Client Add Residents How do I add a resident and assign a pendant or wander transmitter already configured in the system? 1. Login then click the Residents Link at the top of the page 2. Click Add a Resident 3. The Add a Resident window opens 4. Enter the resident s First and Last Name 5. Select a Unit 6. Select a Room 7. Select the appropriate mobile device (Pendant, Wander transmitter, or Chair Sensor) for the resident 8. If applicable, select a Resident Check-In Schedule. Page 10 of 52 Code Alert Series 30 Software User Guide

13 Desktop Client NOTE: If a default has been setup by your administrator, this field will automatically be filled in. If a check-in schedule is not configured in your system, the field will automatically display No Check-In Required. If no check-in schedule is required for the resident but check-in has been configured in your system, you must select No Check-In Required. 9. Click the Add Resident button 10. Repeat as necessary How do I add a resident and assign a new pendant not configured in the system yet? 1. Login then click the Residents Link at the top of the page 2. Click Add a Resident 3. The Add a Resident window opens 4. Enter the resident s First and Last Name 5. Select a Unit 6. Select a Room 7. Click the Add New Pendant button 8. Alarm the new pendant and reset it immediately 9. Once the pendant is listed, click on the ID number to select it 10. If applicable, select a Resident Check-In Schedule 11. Click the Add Resident button 12. Repeat as necessary Code Alert Series 30 Software User Guide Page 11 of 52

14 Desktop Client Modify Resident Information Basic information, facility information, and mobile device information associated with a specific resident can be modified on the individual resident s page. How do I change a resident s name? 1. From the Residents page, click on the resident s name 2. Click the edit pencil next to the Name field 3. Make the appropriate change(s) and click the Update Name button 4. An Update Successful message is displayed in green at the bottom of the page 5. Click the Done button to return to the Residents page Page 12 of 52 Code Alert Series 30 Software User Guide

15 Desktop Client How do I change or remove a resident s check-in schedule: 1. From the Residents page, click on the resident s name 2. Click the edit pencil next to the Check-In field 3. To change the schedule, select the appropriate option from the drop-down list 4. To remove the check-in schedule from the resident record, select No Check-In Required 5. An Update Successful message is displayed in green at the bottom of the page 6. Click the Done button to return to the Residents page Change Mobile Device(s) The mobile devices section allows you to add, update, and/or remove pendants, wander transmitters and/or chair sensors from a resident s record. NOTE: Any mobile device in active alarm CANNOT be changed or removed from a resident until the alert has been addressed. A resident cannot be marked as OFF SITE if their mobile device is in active alarm. If a mobile device is off site but in active alarm (for example, resident taken to the hospital while wearing their pendant), your system administrator must remove or disable the device within the system. Code Alert Series 30 Software User Guide Page 13 of 52

16 Desktop Client How do I change a resident s pendant device assignment? 1. From the Residents page, click on the resident s name 2. Click the edit pencil next to the Pendant field 3. To change the pendant assignment, select the correct pendant from the drop-down list, or click the Add New Pendant button to assign a pendant not yet in the system 4. If adding a new pendant, alarm the pendant and reset it immediately then once the pendant is listed, click on the ID number to select it 5. To remove the pendant assignment, select No Pendant 6. An Update Successful message is displayed in green at the bottom of the page 7. Click the Done button to return to the Residents page How do I change a resident s wander transmitter device assignment? 1. From the Residents page, click on the resident s name 2. Click the edit pencil next to the Transmitter field 3. To change the wander transmitter assignment, select the correct transmitter from the drop-down list 4. To remove the wander transmitter assignment, choose No Transmitter Page 14 of 52 Code Alert Series 30 Software User Guide

17 Desktop Client 5. An Update Successful message is displayed in green 6. Click the Done button to return to the Residents page How do I change a resident s chair sensor device assignment? 1. From the Residents page, click on the resident s name 2. Click the edit pencil next to the Chair Sensor field 3. To change the chair sensor assignment, select the correct sensor from the drop-down list 4. To remove the sensor assignment, choose No Chair Sensor 5. An Update Successful message is displayed in green at the bottom of the page 6. Click the Done button to return to the Residents page Change Site Status A resident s status can be changed to show as Off Site when they will be away from the facility for a period of time. How do I change a resident s status to show as being off site? 1. From the Residents page, click on the resident s name 2. Click the OFF SITE button 3. An Update Successful message is displayed in green at the bottom of the page 4. Click the Done button to return to the Residents page Code Alert Series 30 Software User Guide Page 15 of 52

18 Desktop Client How do I change a resident s status to show that they are on site? There are a couple of ways to return the resident s status to On Site. 1. From the Residents page, click on the resident s name 2. Click the ON SITE button 3. An Update Successful message is displayed in green at the bottom of the page 4. Click the Done button to return to the Residents page --Or-- 1. Once the resident is back in the facility, alarm the resident s pendant 2. The status will automatically change to On Site Transfer The transfer feature allows for a resident to be moved (transferred) from one unit to another unit or between rooms within the same unit. NOTE: A resident with a device in active alarm CANNOT be transferred until the alert has been addressed. A resident cannot be transferred if they are marked as being OFF SITE. How do I transfer a resident that has a QR+ pendant or chair sensor assigned to them? 1. From the Residents page, click on the resident s name 2. Click the Transfer button next to the Unit-Room field Page 16 of 52 Code Alert Series 30 Software User Guide

19 Desktop Client 3. Select a new unit assignment from the drop-down list if moving to another unit within the facility 4. Select the new room assignment from the drop-down list (if the room does not appear in the list, you may need to select a different unit first) 5. The Transfer button changes to processing (transfer is immediate) 6. When the Transfer button displays again, click the Done button to return to the Residents page How do I transfer a resident that has a 9450 wander transmitter assigned to them to another room within the same unit? 1. From the Residents page, click on the resident s name 2. Click the Transfer button next to the Unit-Room field 3. Select the new room assignment from the drop-down list (if the room does not appear in the list, you may need to select a different unit first) 4. The Transfer button changes to processing (transfer is immediate) 5. When the Transfer button displays again, click the Done button to return to the Residents page Code Alert Series 30 Software User Guide Page 17 of 52

20 Desktop Client How do I transfer a resident that has a 9450 wander transmitter assigned to them to another unit within the facility? 1. From the Residents page, click on the resident s name 2. Click the Transfer button next to the Unit-Room field 3. Select a new unit assignment from the drop-down list 4. Select the new room assignment from the drop-down list 5. The Transfer button changes to Cancel Transfer 6. Click the Done button to return to the Residents page 7. The Residents page will display Transfer in Progress next to the resident s name 8. Once the resident has passed through a door in the new unit, the transfer process will automatically be completed Page 18 of 52 Code Alert Series 30 Software User Guide

21 Desktop Client Remove Residents How do I remove a resident from the system? 1. From the Residents page, click on the resident s name 2. Click the Remove Resident button 3. The button will change to Confirm Remove? You must click the button again in order to remove the resident. Resident Reports Reports for residents are available within their individual records. To view a resident report: 1. From the Residents page, click on the resident s name 2. In the Reports section, click the activity link for either the Last 7 Days or Last 30 Days reports 3. Export the report to a.pdf file,.csv file, or 4. Once exported, you can view, save, or print the report 5. Close the report view page 6. Click the Done button to return to the Residents page 7. Repeat for each individual resident report Code Alert Series 30 Software User Guide Page 19 of 52

22 Desktop Client This page intentionally left blank. Page 20 of 52 Code Alert Series 30 Software User Guide

23 Mobile Client MOBILE CLIENT Residents Page Like the Residents page on the Desktop Client, you can add, update, and remove residents from the system, change their status, as well add new pendants to the system. Reports however are not available on the Mobile Client. Resident information is divided into three (3) categories: Basic Information resident name Facility Information resident unit/room assignment and checkin schedule Mobile Devices pendants, wander transmitters, and/or chair sensors assigned to the resident Depending upon your screen size, you may need to scroll to view all the information. Code Alert Series 30 Software User Guide Page 21 of 52

24 Mobile Client Add Residents How do I add a resident and assign a pendant already configured in the system? 1. Login then select the Residents Link at the top of the page 2. Select the Add a Resident icon 3. The Add a Resident window opens 4. Enter the resident s First and Last Name 5. Select a Unit 6. Select a Room 7. Select the appropriate mobile device (Pendant or Wander transmitter) 8. If applicable, select a Chair Sensor for the resident 9. If applicable, select a Resident Check-In Schedule. Page 22 of 52 Code Alert Series 30 Software User Guide

25 Mobile Client NOTE: If a default has been setup by your administrator, this field will automatically be filled in. If check-in schedule is not configured in your system, the field will automatically display No Check-In Required. If no check-in schedule is required for the resident but check-in has been configured in your system, you must select No Check-In Required. 10. Select the Add Resident button 11. Repeat as necessary How do I add a resident and assign a new pendant not configured in the system yet? 1. Login then select the Residents Link at the top of the page 2. Select the Add a Resident icon 3. The Add a Resident window opens 4. Enter the resident s First and Last Name 5. Select a Unit 6. Select a Room 7. Select the Add New Pendant button 8. Alarm the new pendant and reset it immediately 9. Once the pendant is listed, click on the ID number to select it 10. If applicable, select a Resident Check-In Schedule. 11. Select the Add Resident button 12. Repeat as necessary Code Alert Series 30 Software User Guide Page 23 of 52

26 Mobile Client Modify Resident Information Basic information, facility information, and mobile device information associated with a specific resident can be modified on the individual resident s page. How do I change a resident s name? 1. From the Residents page, select the resident s name 2. Select the edit pencil next to the Name field 3. Make the appropriate change(s) and select the Update Name button 4. An Update Successful message is displayed in green at the bottom of the page 5. Select Done to return to the Residents page Page 24 of 52 Code Alert Series 30 Software User Guide

27 Mobile Client How do I change or remove a resident s check-in schedule: 1. From the Residents page, select the resident s name 2. Select the edit pencil next to the Check-In field 3. To change the schedule, select the appropriate option from the drop-down list 4. To remove the check-in schedule from the resident record, select No Check-In Required 5. An Update Successful message is displayed in green at the bottom of the page 6. Select Done to return to the Residents page Change Mobile Device(s) The mobile devices section allows you to add, update, and/or remove pendants, wander transmitters and chair sensors from the resident s record. NOTE: Any mobile device in active alarm CANNOT be changed or removed from a resident until the alert has been addressed. A resident cannot be marked as OFF SITE if their mobile device is in active alarm. If a mobile device is off site but in active alarm (for example, resident taken to the hospital while wearing their pendant), your system administrator must remove or disable the device within the system. Code Alert Series 30 Software User Guide Page 25 of 52

28 Mobile Client How do I change a resident s pendant device assignment? 1. From the Residents page, select the resident s name 2. Select the edit pencil next to the Pendant field 3. To change the pendant assignment, select the correct pendant from the dropdown list, or select the Add New Pendant button to assign a pendant not yet in the system 4. If adding a new pendant, alarm the pendant and reset it immediately then once the pendant is listed, click on the ID number to select it 5. To remove the pendant assignment, select No Pendant 6. An Update Successful message is displayed in green at the bottom of the page 7. Select Done to return to the Residents page How do I change a resident s wander transmitter device assignment? 1. From the Residents page, select the resident s name 2. Select the edit pencil next to the Transmitter field 3. To change the wander transmitter assignment, select the correct transmitter from the drop-down list 4. To remove the wander transmitter assignment, choose No Transmitter Page 26 of 52 Code Alert Series 30 Software User Guide

29 Mobile Client 5. An Update Successful message is displayed in green at the bottom of the page 6. Select Done to return to the Residents page How do I change a resident s chair sensor device assignment? 1. From the Residents page, click on the resident s name 2. Click the edit pencil next to the Chair Sensor field 3. To change the chair sensor assignment, select the correct sensor from the dropdown list 4. To remove the sensor assignment, choose No Chair Sensor 5. An Update Successful message is displayed in green at the bottom of the page 6. Click the Done button to return to the Residents page Change Site Status A resident s status can be changed to show as Off Site when they will be away from the facility for a period of time. How do I change a resident s status to show as being off site? 1. From the Residents page, select the resident s name 2. Select OFF SITE 3. An Update Successful message is displayed in green at the bottom of the page 4. Click Done to return to the Residents page Code Alert Series 30 Software User Guide Page 27 of 52

30 Mobile Client How do I change a resident s status to show that they are on site? There are a couple of ways to return the resident s status to On Site. 1. From the Residents page, select the resident s name 2. Select ON SITE 3. An Update Successful message is displayed in green at the bottom of the page 4. Click Done to return to the Residents page --Or-- 5. Once the resident is back in the facility, alarm the resident s pendant 6. The status will automatically change to On Site Transfer The transfer feature allows for a resident to be moved (transferred) from one unit to another unit or between rooms within the same unit. NOTE: A resident with a device in active alarm CANNOT be transferred until the alert has been addressed. A resident cannot be transferred if they are marked as being OFF SITE. How do I transfer a resident that has a QR+ pendant or chair sensor assigned to them? 1. From the Residents page, click on the resident s name 2. Click the Transfer button under the Unit- Room field Page 28 of 52 Code Alert Series 30 Software User Guide

31 Mobile Client 3. Select a new unit assignment from the drop-down list if moving to another unit within the facility 4. Select the new room assignment from the drop-down list (if the room does not appear in the list, you may need to select a different unit first) 5. The Transfer button changes to processing (transfer is immediate) 6. When the Transfer button displays again, click the Done button to return to the Residents page How do I transfer a resident that has a 9450 wander transmitter assigned to them to another room within the same unit? 1. From the Residents page, click on the resident s name 2. Click the Transfer button under the Unit- Room field 3. Select the new room assignment from the drop-down list (if the room does not appear in the list, you may need to select a different unit first) 4. The Transfer button changes to processing (transfer is immediate) 5. When the Transfer button displays again, click the Done button to return to the Residents page Code Alert Series 30 Software User Guide Page 29 of 52

32 Mobile Client How do I transfer a resident that has a 9450 wander transmitter assigned to them to another unit within the facility? 1. From the Residents page, click on the resident s name 2. Click the Transfer button under the Unit- Room field 3. Select a new unit assignment from the drop-down list 4. Select the new room assignment from the drop-down list 5. The Transfer button changes to Cancel Transfer 6. Click the Done button to return to the Residents page 7. The Residents page will display Transfer in Progress next to the resident s name 8. Once the resident has passed through a door in the new unit, the transfer process will automatically be completed Page 30 of 52 Code Alert Series 30 Software User Guide

33 Mobile Client Remove Residents How do I remove a resident from the system? 1. From the Residents page, select the resident s name 2. Select the Remove button 3. The button will change to Confirm? You must click the button again in order to remove the resident. Code Alert Series 30 Software User Guide Page 31 of 52

34 Mobile Client This page intentionally left blank. Page 32 of 52 Code Alert Series 30 Software User Guide

35 Alerts ALERTS Alerts Alerts are displayed sequentially as they occur, by priority (in order of newest to oldest), and are color coded according to the alert type. Flashing Red Top Priority Red High Priority Yellow Medium Priority (Equipment) Gray Care Classification only When an event occurs an alarm is sounded and a message is displayed on the Client computer(s) monitoring the device or resident s room. The number located after ALARMS is the number of all active alarms for areas the client computer is monitoring. NOTE: With any alert, always follow your facility s policies/procedures to ensure patient safety and secure the area. Code Alert Series 30 Software User Guide Page 33 of 52

36 Alerts Claim The software gives caregivers the ability to coordinate their response to individual resident requests using the Claim feature to claim alarms. Once resolved, caregivers can classify the alarm from the app to track services delivered and/or trend resident alerts over time. NOTE: This feature requires that you are logged into the system. If you are not logged in, you will be prompted to login before claiming. Desktop Client Mobile Client How do I claim an alert? 1. Once logged into the system, claim the alarm by pressing the alarm s Claim button Page 34 of 52 Code Alert Series 30 Software User Guide

37 Alerts 2. When you take responsibility for an alarm, the button disappears and Claimed By is displayed on all devices receiving the alert Flashing Red Alerts Flashing red alerts are Top Priority/ Emergency and include: Priority Alert (Action is Required) Priority Assist (Assistance is Required) Priority High Temp (High Temperature) Priority Low Temp (Low Temperature) Priority Open (Open Reported) Priority Out of Bed (Bed Sensor) Priority Out of Chair (Chair Sensor) Priority Smoke (Smoke Detector) Priority alerts are only available for QR Plus devices and must be configured at the device level in order to display. These types of alerts are provided to give the facility the flexibility to distinguish different alerts (for example, a resident alert triggered in the bathroom might require more urgency than another alert). Common Causes Resident pulls the cord on a Pull Cord A motion sensor within a Resident s room, immediate area, or a common area is triggered Code Alert Series 30 Software User Guide Page 35 of 52

38 Alerts Priority Alert Priority Assist Priority High Temp Priority Low Temp An Alert indicates a generic alarm that covers events not already addressed with other alarms but does require action to be taken. Common Causes Doorbell was pushed Water detector sensed the presence of water Assistance Required alarm indicates that a resident s device has been activated. NOTE: Assistance Required Alarms must be reset at the alarming device. Common Causes Resident presses a button on a Call Pendant or pulls the cord on a Pull Cord A motion sensor within a Resident s room, immediate area, or a common area is triggered High Temp indicates that the ambient temperature is above the pre-defined thresholds. Common Causes Air conditioner or furnace not working properly Window left open Low Temp indicates that the ambient temperature is below the pre-defined thresholds. Common Causes Air conditioner or furnace not working properly Window left open Page 36 of 52 Code Alert Series 30 Software User Guide

39 Alerts Priority Open Priority Out of Bed Priority Out of Chair Priority Smoke Open Reported indicates that an interior door or window alarm has been activated. Common Causes A monitored medicine cabinet, cleaning supply closet, apartment door, etc has been opened A monitored window has been opened An Out of Bed alert indicates that weight is no longer being applied to the sensor pad. NOTE: Out of Bed Alarms can be reset by reapplying weight to the sensor pad or by pressing the Hold/Reset button. Common Causes Resident removes his/her weight from a Sensatec Fall Management System bed sensor pad An Out of Chair alert indicates that weight is no longer being applied to the sensor pad. NOTE: Out of Chair Alarms can be reset by reapplying weight to the sensor pad or by pressing the Hold/Reset button. Common Causes Resident removes his/her weight from a Sensatec Fall Management System chair sensor pad Smoke Alarm indicates that a smoke detector that is integrated with the system has been activated. Common Causes Smoke was detected Test performed on the detector Code Alert Series 30 Software User Guide Page 37 of 52

40 Alerts How To How do I respond to a priority alert? 1. Locate the device or proceed to the door or exit in alarm 2. Verify that no resident emergency exists. 3. Reset the alarming device If the Door Alarm was generated by a Door/Window with Manual Reset device, you must press the manual reset button after the door/window is closed to reset For a fall triggered alert, the system will automatically reset and begin monitoring once the resident is placed back on the Sensor Pad NOTE: If Care Classification is turned on in your system, there is an additional step that must be completed. Once the alarm is reset, the flashing red alarm message will disappear and a gray alarm message will display on the client computer. For Nurse Call and Pull Cord with Check-In devices, the alarm can automatically be cleared by pushing the Check-In button For all other devices, open the Alarms page on the client computer, click the Select dropdown, and choose the appropriate event from the list Page 38 of 52 Code Alert Series 30 Software User Guide

41 Alerts NOTE: This feature requires that you are logged into the system. If you are not logged in, you will be prompted to login before being able to classify. Desktop Client Mobile Client Red Alerts Alert Red alerts are High Priority and include: Alert Assistance Required Check Bathroom Check Resident Depleted Battery Door Alarm High Temperature Loiter Low Temperature Open Reported Out of Bed Out of Chair Reconnecting Smoke System Down System is Down An Alert indicates a generic alarm that covers events not already addressed with other alarms but does require action to be taken. Code Alert Series 30 Software User Guide Page 39 of 52

42 Alerts Assistance Required Check Bathroom Common Causes Doorbell was pushed Resident removes his/her weight from a Sensatec Fall Management System sensor pad Assistance Required alarm indicates that a resident s device has been activated. NOTE: Assistance Required Alarms must be reset at the alarming device. Common Causes Resident presses a button on a Call Pendant or pulls the cord on a Pull Cord A motion sensor within a Resident s room, immediate area, or a common area is triggered Check Bathroom indicates that no activity from a resident has been detected over a certain period of time. Common Causes Resident is ill or may have fallen in the bathroom Resident fell asleep while in the bathroom Resident is having difficulty lifting themselves or may need help getting back into bed Resident may be confused, worried, or not know where they are and require assistance Page 40 of 52 Code Alert Series 30 Software User Guide

43 Alerts Check Resident Depleted Battery Door Alarm No message has been received from resident s wander transmitter or room device during the Resident Check-In period. Common Causes An event (for example, taking medication at a certain time) was not completed within the scheduled timeframe so the device wasn t activated Depleted Battery alarm indicates that a device has been in low battery alarm for an extended period of time and finally fails to communicate with the system. NOTE: When a device displays a depleted battery alarm, try replacing the battery. If that doesn t work then the entire device must be replaced. Door Alarm indicates that an alert has been activated at an exterior door or exit. Common Causes Failed to enter a bypass code before opening a monitored door Door is opened when scheduled to be locked An active wander transmitter has come to close to an open door Code Alert Series 30 Software User Guide Page 41 of 52

44 Alerts High Temperature Loiter Low Temperature High Temp indicates that the ambient temperature is above the pre-defined thresholds. Common Causes Air conditioner or furnace not working properly Window left open Loiter events are created when a resident with an Adult or CodeWatch transmitter remains in range of a monitored door for longer than the Loiter Delay. If the resident is in range of multiple doors, the door that is displayed at the Client computer is the door that first reported the wander transmitter. Common Causes A resident with a wander transmitter remains in range of a monitored door for longer than the Loiter Delay Low Temp indicates that the ambient temperature is below the pre-defined thresholds. Common Causes Air conditioner or furnace not working properly Window left open Page 42 of 52 Code Alert Series 30 Software User Guide

45 Alerts Open Reported Out of Bed Out of Chair Open Reported indicates that an interior door or window alarm has been activated. Common Causes A monitored medicine cabinet, cleaning supply closet, apartment door, etc has been opened A monitored window has been opened An Out of Bed alert indicates that weight is no longer being applied to the sensor pad. NOTE: Out of Bed Alarms can be reset by reapplying weight to the sensor pad or by pressing the Hold/Reset button. Common Causes Resident removes his/her weight from a Sensatec Fall Management System bed sensor pad An Out of Chair alert indicates that weight is no longer being applied to the sensor pad. NOTE: Out of Chair Alarms can be reset by reapplying weight to the sensor pad or by pressing the Hold/Reset button. Common Causes Resident removes his/her weight from a Sensatec Fall Management System chair sensor pad Code Alert Series 30 Software User Guide Page 43 of 52

46 Alerts Smoke Reconnecting System Down Smoke Alarm indicates that a smoke detector that is integrated with the system has been activated. Common Causes Smoke was detected Test performed on the detector Reconneting alerts are only available on the mobile clients. These types of alerts indicate that the connection to the server has been lost for the mobile device. Common Causes Wi-Fi connection was lost Server is down The System Down Alarm occurs when the connection from the port server to the computer is lost, when connected hardware (network coordinator, Comp2 paging base, or TAP paging base) fails, or when internal components fail. When this happens, alerts coming in are no longer transferring to the Server. Common Causes Faulty wiring to a device Invalid network address System failed to receive check-in signal for a monitored device Port server turned off, logged off or software improperly shut down Dip switches not configured correctly Page 44 of 52 Code Alert Series 30 Software User Guide

47 Alerts System is Down System is Down indicates that all communications between the server and client computer has been lost. The system is in a non-functional state and must be addressed immediately. NOTE: A System Down alarm will automatically clear when communications with the Server is restored. It cannot be cleared by the user. How do I respond to a system down alert? Note any information that may be helpful when communicating the event, then contact your System Administrator. How To How do I respond to a red alert? 1. Locate the device or proceed to the door or exit in alarm 2. Verify that no resident emergency exists. 3. Reset the alarming device For an Exit Alarm Control unit enter the four-digit security code in the keypad If the Door Alarm was generated by a Door/Window with Manual Reset device, you must press the manual reset button after the door/window is closed to reset For a fall triggered alert, the system will automatically reset and begin monitoring once the resident is placed back on the Sensor Pad Code Alert Series 30 Software User Guide Page 45 of 52

48 Alerts NOTE: If Care Classification is turned on in your system, there is an additional step that must be completed. Once the alarm is reset, the red alarm message will disappear and a gray alarm message will display on the client computer. For Nurse Call and Pull Cord with Check-In devices, the alarm can automatically be cleared by pushing the Check-In button For all other devices, open the Alarms page on the client computer, click the Select dropdown, and choose the appropriate event from the list NOTE: This feature requires that you are logged into the system. If you are not logged in, you will be prompted to login before being able to classify. Desktop Client Mobile Client Page 46 of 52 Code Alert Series 30 Software User Guide

49 Alerts Yellow Alerts Communication Failure Low Battery On Battery Power Yellow Alerts are medium priority, typically related to equipment, and include: Communication Failure Low Battery On Battery Power RF Interference Tamper Communication Failure alarm indicates that a device is not communicating with the system or a tamper was detected. Common Causes Radio frequency noise interference on system Faulty wiring to device Loss of power to the system Invalid network address Device disabled due to device tampering No poll received by the system from monitored devices Network connection broken NOTE: If alarm persists, contact your Super User or call Technical Support 24 hours at Low Battery alarm indicates that a device s battery needs to be replaced. On Battery Power alarm indicates that a QR Plus repeater is running on battery power only and if not addressed, can lead to low battery and/or communication failure. Code Alert Series 30 Software User Guide Page 47 of 52

50 Alerts RF Interference Tamper RF Interference indicates that radio frequency is interrupting system communications to 9450 door exit alarm control units. Common Causes Radio frequency noise interference near door (for example, electronic doors opening, elevators, appliances, lighting, etc ) The tamper functionality operates in several modes depending on the device and the type of tamper interference. Below is a table showing the type of tamper event associated with a particular device. Tamper Nurse Call EAC Door/ Window Door Manual Reset Door Check-In PIR Case Open X X X X X X External Enclosure X Cord Removed X How To How do I respond to a yellow alert? 1. Note any information that may be helpful when communicating the event, then contact your System Administrator. Page 48 of 52 Code Alert Series 30 Software User Guide

51 Alerts Quick Look Display The following chart shows the correlation between how alerts are displayed on the Quick Look Display, alert color, and what is displayed on the Client computer. Quick Look Prio Color Flash Red Client Computer Priority Alert Priority Assist Priority High Temp Priority Low Temp Priority Open Priority Out of Bed Priority Out of Chair Priority Smoke SysDwn Red System Down Assist Check Check HiTemp LoTemp Open OutBed OutChr Smoke Door Alert DepBat Loiter Assistance Required Check Bathroom Check Resident High Temperature Low Temperature Open Reported Out of Bed Out of Chair Smoke Door Alarm Alert Depleted Battery Loiter Tamper Yellow Tamper RF Int Comm LowBat OnBat RF Interference Communication Failure Low Battery On Battery Power Code Alert Series 30 Software User Guide Page 49 of 52

52 Alerts This page intentionally left blank. Page 50 of 52 Code Alert Series 30 Software User Guide

53 Revision History REVISION HISTORY Revision A B C D Change Release Removed: Purple Alerts section and device emergency alert functionality Updated: Login information for HTTPS Added: Top Priority Alerts Added: Unit and Chair Sensor fields to resident information Added: High Temperature, Low Temperature, Out of Bed and Out of Chair to Flashing Red Alerts section Added: Check Bathroom, High Temperature, Low Temperature, Out of Bed, and Out of Chair to High Red Alerts section Added: Transfer functionality Added: Login requirement for claiming and classifying alerts Code Alert Series 30 Software User Guide Page 51 of 52

54 Revision History This page intentionally left blank. Page 52 of 52 Code Alert Series 30 Software User Guide

55

56 3125 North 126th Street, Brookfield, WI Phone fax Release Date: 06/2018

CODE ALERT Enterprise Software User Guide

CODE ALERT Enterprise Software User Guide CODE ALERT Enterprise Software User Guide 2018 RF Technologies, Inc. All specifications subject to change without notice. All Rights Reserved. No Part of this work may be reproduced or copied in any form

More information

RFT CARES Android App User Guide

RFT CARES Android App User Guide RFT CARES Android App User Guide 2017 RF Technologies, Inc. All specifications subject to change without notice. All Rights Reserved. No Part of this work may be reproduced or copied in any form or by

More information

Touchpad Exit Controller Administration Guide

Touchpad Exit Controller Administration Guide Touchpad Exit Controller Administration Guide 2018 RF Technologies, Inc. All specifications subject to change without notice. All Rights Reserved. No Part of this work may be reproduced or copied in any

More information

Ion Gateway Cellular Gateway and Wireless Sensors

Ion Gateway Cellular Gateway and Wireless Sensors Page 1 of 9 Account & Network Setup If this is your first time using the Ion Gateway online system site you will need to create a new account. If you have already created an account you can skip to the

More information

D3D Wi-Fi GSM Smart Alarm System -User Manual

D3D Wi-Fi GSM Smart Alarm System -User Manual D3D Wi-Fi GSM Smart Alarm System -User Manual D3D Wi-Fi / GSM Smart Alarm system (Model : D10). Please read all instructions carefully & follow steps for easy home installation. 1 P a g e D3D Wi-Fi / GSM

More information

Alarm Client. Installation and User Guide. NEC NEC Corporation. May 2009 NDA-30364, Revision 9

Alarm Client. Installation and User Guide. NEC NEC Corporation. May 2009 NDA-30364, Revision 9 Alarm Client Installation and User Guide NEC NEC Corporation May 2009 NDA-30364, Revision 9 Liability Disclaimer NEC Corporation reserves the right to change the specifications, functions, or features,

More information

Touchpad Exit Controller User Guide

Touchpad Exit Controller User Guide Touchpad Exit Controller User Guide 2018 RF Technologies, Inc. All specifications subject to change without notice. All Rights Reserved. No Part of this work may be reproduced or copied in any form or

More information

Patriot Systems Limited

Patriot Systems Limited COPYRIGHT 1997 - The Patriot Systems Ltd. Patriot Alarm Monitoring Automation Package is licensed for use on one computer, by the original person, or company, or organization whose name is registered with

More information

Skyresponse ThingWorx Extension. Version 1.0. User Guide

Skyresponse ThingWorx Extension. Version 1.0. User Guide Skyresponse ThingWorx Extension Version 1.0 User Guide Software Change Log...1 Introduction...1 About Skyresponse...1 Installation...2 Importing the Skyresponse ThingWorx Extension...2 Configuration and

More information

NextGen Home Security. Quick Reference Guide

NextGen Home Security. Quick Reference Guide TM NextGen Home Security Quick Reference Guide Fire Auxiliary Panic (not active) Stay Away Chime Reset Bypass To view the full user manual, go to www.bellaliant.net/homesecurity and select Support. Arming

More information

HikCentral Web Client. User Manual

HikCentral Web Client. User Manual HikCentral Web Client User Manual Legal Information User Manual 2018 Hangzhou Hikvision Digital Technology Co., Ltd. About this Manual This Manual is subject to domestic and international copyright protection.

More information

Operation Manual Fighter ProVision Software. Version: 0.0 Revision: 1

Operation Manual Fighter ProVision Software. Version: 0.0 Revision: 1 Operation Manual Fighter ProVision Software Version: 0.0 Revision: 1 TABLE OF CONTENTS 1. Introduction 5 2. Software Installation 5 3. PC Users 6 3.1 Introduction 6 3.2 Default Code 6 3.3 Edit PC User

More information

HikCentral Web Client. User Manual

HikCentral Web Client. User Manual HikCentral Web Client User Manual Legal Information User Manual 2018 Hangzhou Hikvision Digital Technology Co., Ltd. About this Manual This Manual is subject to domestic and international copyright protection.

More information

Peak Partners Web-Programmable Thermostat Homeowner s Manual. Look inside for a complete guide to the setup and operation of your new thermostat.

Peak Partners Web-Programmable Thermostat Homeowner s Manual. Look inside for a complete guide to the setup and operation of your new thermostat. Peak Partners Web-Programmable Thermostat Homeowner s Manual Look inside for a complete guide to the setup and operation of your new thermostat. Table of Contents Step 1: Getting Started...4-6 A. Thermostat

More information

IT801 Thermostat. User s Manual. The complete guide to the set up and operation of your new smart Wi-Fi thermostat.

IT801 Thermostat. User s Manual. The complete guide to the set up and operation of your new smart Wi-Fi thermostat. IT801 Thermostat User s Manual The complete guide to the set up and operation of your new smart Wi-Fi thermostat. The smart Wi-Fi thermostat system learns your comfort preferences, then finds opportunities

More information

Wi-Fi 3-IN-1 Trio Sensor

Wi-Fi 3-IN-1 Trio Sensor Wi-Fi 3-IN-1 Trio Sensor (WTS3100) User Manual home8alarm.com 1-844-800-6482 support@home8alarm.com Table of Contents Chapter 1. Introduction... 2 1.1 System Requirements... 3 Chapter 2. Hardware Overview...

More information

abode Web app Functionality

abode Web app Functionality abode Web app Functionality System mode display controls the state of the alarm system. The user can change the mode of the system by simply clicking on the desired mode. When arming the system with the

More information

Contents 1 Set Up 2 Gateway information 3 Operation of the App 4 Troubleshooting Description of sensors. 1 Set Up. 1.1 Connect the Gateway

Contents 1 Set Up 2 Gateway information 3 Operation of the App 4 Troubleshooting Description of sensors. 1 Set Up. 1.1 Connect the Gateway Contents 1 Set Up 2 Gateway information 3 Operation of the App 4 Troubleshooting Description of sensors 1 Set Up After downloading the Weatherhub app, follow these steps: 1.1 Connect the Gateway Connect

More information

A1UL PERS. Personal Emergency Response System. For Technical Support Please Contact Your Service Provider Or Distributor

A1UL PERS. Personal Emergency Response System. For Technical Support Please Contact Your Service Provider Or Distributor A1UL PERS Personal Emergency Response System TABLE OF CONTENTS 1. READ THIS FIRST... 1 2. SYSTEM OVERVIEW.. 1 3. COMPONENTS 2 4. UNIT OPERATION! Standby Mode.. 3! Emergency Activation. 3! Answering Incoming

More information

IQ PANEL USER GUIDE SMARTHOME.

IQ PANEL USER GUIDE SMARTHOME. IQ PANEL USER GUIDE SECURITY & SMARTHOME www.schmidtsecurity.com USING YOUR SYSTEM: BASICS Navigation Move from page to page and access information on each page using finger touches, swipes, and scrolling.

More information

Advisor Advanced Mobile Application User Manual

Advisor Advanced Mobile Application User Manual Advisor Advanced Mobile Application User Manual Content Warnings and Disclaimers 2 Advanced Mobile 2 Contact information 2 Description 2 Screen navigation 4 Gestures 4 Menu 4 Help navigation 4 Login 5

More information

Register the Gateway via PC. Package Content. Gateway Installation. 1 x Gateway 1 x Voice Siren 1 x IP Camera*

Register the Gateway via PC. Package Content. Gateway Installation. 1 x Gateway 1 x Voice Siren 1 x IP Camera* Package Content 1 x Gateway 1 x Voice Siren 1 x IP Camera* Register the Gateway via PC Create a new account at www.elro-smartalarm.com 1. Click on Create a new account 1 x PIR Motion 1 x Magnetic 1 x Remote

More information

MultiSite Manager. Setup Guide

MultiSite Manager. Setup Guide MultiSite Manager Setup Guide Contents 1. Introduction... 2 How MultiSite Manager works... 2 How MultiSite Manager is implemented... 2 2. MultiSite Manager requirements... 3 Operating System requirements...

More information

Halton SAFE / 7.14 user guide and installation instructions

Halton SAFE / 7.14 user guide and installation instructions Halton SAFE / 7.14 user guide and installation instructions VERIFIED SOLUTIONS BY H A LTO N Enabling Wellbeing Table of contents 1 System description 3 2 User Accounts 4 3 Main menu 7 3.1 Main menu - Change

More information

Using ANM Mobile CHAPTER

Using ANM Mobile CHAPTER CHAPTER 19 Date: 3/22/13 This chapter describes Cisco ANM Mobile, which allows you to access your ANM server or ANM Virtual Appliance and manage your devices using a mobile device such as an iphone or

More information

Avigilon Control Center System Integration Guide

Avigilon Control Center System Integration Guide Avigilon Control Center System Integration Guide with Gallagher Command Centre INT-CARDAX-C-Rev3 Copyright 2013 Avigilon. All rights reserved. No copying, distribution, publication, modification, or incorporation

More information

For Android devices MYQ-G0301 MYQ-G0301C MYQ-G0301D MYQ-G0301LA

For Android devices MYQ-G0301 MYQ-G0301C MYQ-G0301D MYQ-G0301LA Smart Smart Garage Garage Hub Hub Manual Manual For Android devices MYQ-G0301 MYQ-G0301C MYQ-G0301D MYQ-G0301LA by Before You Start To reduce the risk of SEVERE INJURY to persons: DO NOT enable the MyQ

More information

Notice... 1 Trademarks... 1 US Patent Numbers... 1 Technical Services Contact Information... 2 Document Conventions... 2 Warranty...

Notice... 1 Trademarks... 1 US Patent Numbers... 1 Technical Services Contact Information... 2 Document Conventions... 2 Warranty... Table of Contents Preface 1 Notice... 1 Trademarks... 1 US Patent Numbers... 1 Technical Services Contact Information... 2 Document Conventions... 2 Warranty... 2 Chapter 1 Radius Overview 6 1.1 About

More information

Avigilon Control Center 5 System Integration Guide

Avigilon Control Center 5 System Integration Guide Avigilon Control Center 5 System Integration Guide for Paxton Net2 Access Control Systems 2014 Avigilon Corporation. All rights reserved. Unless expressly granted in writing, no license is granted with

More information

Patriot Systems Limited

Patriot Systems Limited COPYRIGHT 1997 - The Patriot Systems Ltd. Patriot Alarm Monitoring Automation Package is licensed for use on one computer, by the original person, or company, or organisation whose name is registered with

More information

For ios devices MYQ-G0301 MYQ-G0301C MYQ-G0301-D MYQ-G0301LA

For ios devices MYQ-G0301 MYQ-G0301C MYQ-G0301-D MYQ-G0301LA Smart Smart Garage Garage Hub Hub Manual Manual For ios devices MYQ-G0301 MYQ-G0301C MYQ-G0301-D MYQ-G0301LA by Before You Start To reduce the risk of SEVERE INJURY to persons: DO NOT enable the MyQ Smart

More information

Door/Window Sensor. Set-Up Guide

Door/Window Sensor. Set-Up Guide Door/Window Sensor Set-Up Guide Thanks for choosing Rogers Smart Home Monitoring! Once you ve set-up your Door/Window Sensor, you can receive notifications if a window or door in your home opens unexpectedly.

More information

HEGA Ethernet Gateway Browser Interface Guide

HEGA Ethernet Gateway Browser Interface Guide HEGA Ethernet Gateway Web Interface HEGA Ethernet Gateway Browser Interface Guide Table of Contents Introduction: Browser Interface Guide 3 Common Tasks: 4 Check-in Reports 5 Check-in Administration 5

More information

Professionally Monitored Service User Guide

Professionally Monitored Service User Guide Midco SmartHOME Professionally Monitored Service User Guide Learn how to protect the things that matter most with this instruction guide for professionally monitored Midco SmartHOME service. 07 Midcontinent

More information

ViewMatrix. Software for Online Monitoring & Control of Matrix2000 Conventional Fire Alarm Panels. Version: 2.0 Revision: 0.1

ViewMatrix. Software for Online Monitoring & Control of Matrix2000 Conventional Fire Alarm Panels. Version: 2.0 Revision: 0.1 ViewMatrix Software for Online Monitoring & Control of Matrix2000 Conventional Fire Alarm Panels Version: 2.0 Revision: 0.1 CONTENTS 1. Introduction...3 2. Keyboard...5 2.1 POWER indication - Normal Operation...5

More information

Quick Response. Plus Wireless Call Solution

Quick Response. Plus Wireless Call Solution Quick Response Plus Wireless Call Solution When your residents need assistance, you want them to have the assurance and confidence that help is on the way. Rely on the Quick Response Plus Wireless Call

More information

0 4 / 0 4 / 1 4. GE Concord 4 Quick User Guide. GE Concord 4 Quick User Guide Page 1

0 4 / 0 4 / 1 4. GE Concord 4 Quick User Guide. GE Concord 4 Quick User Guide Page 1 0 4 / 0 4 / 1 4 GE Concord 4 Quick User Guide GE Concord 4 Quick User Guide Page 1 Before Calling Is the keypad beeping? Press *. This will silence the beeping and let you know where the trouble is. Is

More information

X64 Wireless Training

X64 Wireless Training X64 Wireless Training IDS Contents 1 Contents Features 3 Wireless Hardware 4 IDS & Duevi integration PCB 5 LED operation 5 Wireless Device Hardware setup 6 Location 260 7 LED Keypad Instructions 7 Adding

More information

Paradox Integration Module Settings Guide

Paradox Integration Module Settings Guide Paradox Integration Module Settings Guide List of Terms used in Paradox Integration Module Settings Guide............. 3 Introduction into Paradox Integration Module Settings Guide............... 4 Configuration

More information

SIMPLIFIED HOME SECURITY AND CONTROL

SIMPLIFIED HOME SECURITY AND CONTROL SIMPLIFIED HOME SECURITY AND CONTROL HOME CONTROLLER USER GUIDE HOME CONTROLLER Mediacom introduces a whole new level of security for the things that matter most in your life. Whether you re home or away,

More information

Before you install ProSeries Express Edition software for network use

Before you install ProSeries Express Edition software for network use Before you install ProSeries Express Edition software for network use The following pages describe system requirements and other information you need to know before installing ProSeries Express Edition

More information

Water Hero P-100. P-100 Components:

Water Hero P-100. P-100 Components: Water Hero P-100 Thank you for purchasing the Water Hero P-100. The P-100 offers wholebuilding leak detection, mitigation, and water usage monitoring. P-100 Components: Main Controller Water Meter, Sensor

More information

Cellular Monitoring System

Cellular Monitoring System Cellular Monitoring System Wireless Temperature Monitoring Installation and Operation User s Manual Temperature Monitoring System used in: Temperature-controlled storage rooms and facilities Medical and

More information

Quick Touch Pendant User Guide

Quick Touch Pendant User Guide Quick Touch Pendant User Guide 2018 RF Technologies, Inc. All specifications subject to change without notice. All Rights Reserved. No Part of this work may be reproduced or copied in any form or by any

More information

Avigilon Control Center System Integration Guide

Avigilon Control Center System Integration Guide Avigilon Control Center System Integration Guide with Gallagher Command Centre INT-CARDAX-C-Rev2 Copyright 2011 Avigilon. All rights reserved. No copying, distribution, publication, modification, or incorporation

More information

Protect and connect. Home and away.

Protect and connect. Home and away. Protect and connect. Home and away. USER GUIDE For Additional Support: http://www.cox.com/homesecuritysupport For Additional Support: http://www.cox.com/homesecuritysupport 2 CONTENTS Contents Components

More information

Installing ProSeries 2004

Installing ProSeries 2004 Installing ProSeries 2004 The following instructions will walk you through Installing and Launching ProSeries 2004. Before you begin your installation, it is very important to make note of the following

More information

Installing ProSeries 2005

Installing ProSeries 2005 Installing ProSeries 2005 The following instructions will walk you through Installing and Launching ProSeries 2005. Before you begin your installation, it is very important to make note of the following

More information

D-TECT 2 IP. GJD230 IP Motion Detector

D-TECT 2 IP. GJD230 IP Motion Detector D-TECT 2 IP GJD230 IP Motion Detector PACKAGE CONTENTS 1 x D-TECT 2 IP 1 x Drilling template for fixing holes 3 x 31.75mm wall plugs 3 x 31.75mm screws 2 x Spare sliding curtains 2 x Tamper feet 1 x Tamper

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL INSTALLATION AND OPERATION MANUAL Water Hero P-100 Thank you for purchasing the Water Hero P-100, which offers whole-building leak detection and water conservation monitoring. This box contains: Main Controller

More information

CompleteView Alarm Client User Manual. CompleteView Version 4.6.1

CompleteView Alarm Client User Manual. CompleteView Version 4.6.1 CompleteView Alarm Client User Manual CompleteView Version 4.6.1 Table of Contents Introduction... 1 Overview...2 System Requirements...2 Configuration... 3 Starting the Alarm Client...3 Menus...3 File

More information

RE6100 Series Helix Security and Automation Platform

RE6100 Series Helix Security and Automation Platform CONFIGURATION Resolution Compatibles RE6100 Series Helix Security and Automation Platform C G UI D E Configuration Settings Table 1 - Panel Settings Table 2 - Zone Settings Table 3 - Device Settings Table

More information

Digijock Home Security

Digijock Home Security Digijock Home Security User Manual Congratulations on your purchase! The Digijock Home Security is a wireless alarm system that will protect your home or your small business from fire and burglary. Consisting

More information

D-TECT 3 IP. GJD260 IP Motion Detector

D-TECT 3 IP. GJD260 IP Motion Detector D-TECT 3 IP GJD260 IP Motion Detector PACKAGE CONTENTS 1 x D-TECT 3 IP 1 x Drilling template for fixing holes 3 x 31.75mm wall plugs 3 x 31.75mm screws 2 x Spare sliding curtains 2 x Tamper feet 1 x Tamper

More information

Laptop / PC Programming Manual

Laptop / PC Programming Manual Laptop / PC Programming Manual Doc. # Fire PC Program rev B 01.07 This Document is property of Evax Systems, Inc. The Evax Fire Solutions Programmer Components 2 1.0 System Setup 4 1.1 Interface Setup

More information

With Magictrl, you can control MatiGard anytime & anywhere via your smartphone, even without data network.

With Magictrl, you can control MatiGard anytime & anywhere via your smartphone, even without data network. MatiGard User Guide 02 Menu Feature-------------------------------------------------------------- 05 Overviews---------------------------------------------------------- 07 Read Before Using-----------------------------------------------

More information

Testing the System. Battery Test. Dialer Test. Fire Drill Test (Code + [#] + 69) One-Man Fire Walk-Test (Code + [#] + 68)

Testing the System. Battery Test. Dialer Test. Fire Drill Test (Code + [#] + 69) One-Man Fire Walk-Test (Code + [#] + 68) F A 1 7 0 0 c Testing the System Battery Test When AC power is present, the FA1700C runs a brief battery test every 60 seconds to determine if there is a battery connected, and runs an extended battery

More information

Monitoring Operator Guide. Access Control Manager Software Version

Monitoring Operator Guide. Access Control Manager Software Version Monitoring Operator Guide Access Control Manager Software Version 5.10.10 2018, Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, ACCESS CONTROL MANAGER, ACM, ACM VERIFY AND TRUSTED

More information

Avigilon System Integration Guide. for the Avigilon Control Center and Access Control Manager

Avigilon System Integration Guide. for the Avigilon Control Center and Access Control Manager Avigilon System Integration Guide for the Avigilon Control Center and Access Control Manager 2014-2016, Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON CONTROL CENTER,

More information

DIAMOND II. DARM Delayed Alarm Reporting/Masking. Manual Number AV Revision - A.1 September 3, 2004

DIAMOND II. DARM Delayed Alarm Reporting/Masking. Manual Number AV Revision - A.1 September 3, 2004 Manual Number AV-137622 Revision - A.1 September 3, 2004 DIAMOND II DARM Delayed Alarm Reporting/Masking 791 Park of Commerce Boulevard Suite 100 Boca Raton Florida 33487 www.ge-security.com DIAMOND II

More information

Avigilon System Integration Guide. Avigilon Control Center with AMAG Symmetry Security Management System 7.0

Avigilon System Integration Guide. Avigilon Control Center with AMAG Symmetry Security Management System 7.0 Avigilon System Integration Guide Avigilon Control Center with AMAG Symmetry Security Management System 7.0 2013-2016, Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, HDSM, HIGH

More information

Grandstream Networks, Inc. GDS3710 Input/output Connection Guide

Grandstream Networks, Inc. GDS3710 Input/output Connection Guide Grandstream Networks, Inc. Table of Contents INTRODUCTION... 4 GDS3710 WIRING CONNECTION... 5 Powering and Connecting the GDS3710... 5 Power and Data PINs... 5 Alarm In and Alarm Out PINs... 6 DETECT AND

More information

Avigilon Control Center System Integration Guide

Avigilon Control Center System Integration Guide Avigilon Control Center System Integration Guide with Velocity INT-HIRSCH-A-Rev3 Copyright 2013 Avigilon. All rights reserved. No copying, distribution, publication, modification, or incorporation of this

More information

status AW1 Plus WiFi Alarm System User Manual

status AW1 Plus WiFi Alarm System User Manual status AW1 Plus WiFi Alarm System User Manual Foreword Congratulations on your purchase of the AW1 Plus Alarm system. Before you commence installation we recommend that you unpack the product, familiarise

More information

Carbon Monoxide Sensor

Carbon Monoxide Sensor Carbon Monoxide Sensor Set-Up Guide Thanks for choosing Rogers Smart Home Monitoring! Once you've set-up your Carbon Monoxide Sensor, you can monitor the level of carbon monoxide gas in your home, even

More information

ArchestrA Direct Connect

ArchestrA Direct Connect Table of Contents ArchestrA Direct Connect... 1 Introduction... 1 ArchestrA Direct Connection... 1 ArchestrA Data Source Definition... 2 Data Source Definition... 2 Importing Alarms from ArchestrA... 6

More information

Sensor Cloud User Manual

Sensor Cloud User Manual Sensor Cloud User Manual Table of Contents DEVICES TAB 4 1. DEVICE LIST 4 2. EXPAND ALL 4 3. EXPAND 4 4. STATUS 4 5. DEVICE 4 6. NAME 5 7. MONITORING INTERVAL 5 8. LAST ACTIVITY 5 9. VIEW 5 10. DELETE

More information

Installing ProSeries software for stand-alone use

Installing ProSeries software for stand-alone use Welcome to ProSeries tax software For information about this topic... Look here... Getting ready Page 1 Installing ProSeries software for stand-alone use Page 1 Setting up the ProSeries program Page 3

More information

Rev C May GE Interlogix. Part No: R. CareGard. User Guide

Rev C May GE Interlogix.   Part No: R. CareGard. User Guide g 466-1936 Rev C May 2003 GE Interlogix www.ge-interlogix.com Part No: 60-883-95R CareGard User Guide FCC Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by

More information

HERCULES 6 GRAPHICS SYSTEM

HERCULES 6 GRAPHICS SYSTEM HERCULES 6 GRAPHICS SYSTEM USER MANUAL Protec Fire Detection PLC, Protec House, Churchill Way, Nelson, Lancashire, BB9 6RT. Telephone: +44 (0) 1282 717171 Fax: +44 (0) 1282 717273 Web: www.protec.co.uk

More information

Sensi Multiple Thermostat Manager INSTALLATION GUIDE

Sensi Multiple Thermostat Manager INSTALLATION GUIDE Sensi Multiple Thermostat Manager INSTALLATION GUIDE Multi-thermostat management made easy. Sensi Multiple Thermostat Manager gives you affordable, property-wide comfort control, connected in one place.

More information

QUICK CONSUMER REFERENCE GUIDE

QUICK CONSUMER REFERENCE GUIDE QUICK CONSUMER REFERENCE GUIDE Your System: ADT Smart Home Police Response Starting to use the Alarm Panel, Keypad, ADT Smart Home App and Web Portal PM30 Control Panel Touchscreen Keyfob DT Smart Home

More information

SILENCING AN ALARM When the alarm bell or siren is sounding, enter your user code or present your SecuraProx fob to your keypad.

SILENCING AN ALARM When the alarm bell or siren is sounding, enter your user code or present your SecuraProx fob to your keypad. SYSTEM USER GUIDE SILENCING AN ALARM When the alarm bell or siren is sounding, enter your user code or present your SecuraProx fob to your keypad. IS THIS A FALSE ALARM? YES NO displays. REAL ALARM If

More information

G4S SMARTalarm User Guide

G4S SMARTalarm User Guide G4S SMARTalarm User Guide CONGRATULATIONS WITH YOUR NEW SECURITY SYSTEM! We are glad that you have chosen G4S SMARTalarm. G4S is the largest supplier of security solutions in the world. We have invested

More information

Protégé Eclipse LED Keypad User Manual PRT-KLES

Protégé Eclipse LED Keypad User Manual PRT-KLES Protégé Eclipse LED Keypad User Manual PRT-KLES The specifications and descriptions of products and services contained in this manual were correct at the time of printing. Integrated Control Technology

More information

Ontech GSM 9040/50. Reference Manual English -1 -

Ontech GSM 9040/50. Reference Manual English -1 - Ontech GSM 9040/50 Reference Manual English -1 - Content Welcome... 5 This manual... 5 Text styles... 5 Support... 5 Disclaimer... 5 Overview... 6 Accessories... 6 External temperature sensor 9901... 7

More information

S6 Titan Security System. Wi-Fi and 3G GSM

S6 Titan Security System. Wi-Fi and 3G GSM S6 Titan Security System Wi-Fi and 3G GSM Version 1 - Apr 2018 Table of Contents Introduction 1 Self Monitoring 1 GSM SIM Card and Land Line 1 Free Mobile App (iphone / Android) 1 Pre-Programmed Accessories

More information

Raytec Avigilon Integration User Guide Integrating Raytec Network Illuminators with Avigilon Control Center Document Revision 2.0

Raytec Avigilon Integration User Guide Integrating Raytec Network Illuminators with Avigilon Control Center Document Revision 2.0 Raytec Avigilon Integration User Guide Integrating Raytec Network Illuminators with Avigilon Control Center Document Revision 2.0 Table of Contents 1 INTRODUCTION... 3 1.1 OVERVIEW... 3 1.2 SOFTWARE COMPONENTS...

More information

Maintenance Manual PC6010. WARNING This manual contains information on limitations regarding product use and function

Maintenance Manual PC6010. WARNING This manual contains information on limitations regarding product use and function WARNING This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully

More information

Cellular Monitoring System

Cellular Monitoring System Cellular Monitoring System Wireless Temperature Monitoring Installation and Operation User s Manual For Firmware Versions 4.01-5.12 Temperature Monitoring System used in: Temperature-controlled storage

More information

U ser's Guide PC6010

U ser's Guide PC6010 User's Guide PC6010 Quick Reference Guide This manual is for Basic and Advanced users. Each of these types of user can access a different set of functions. The and symbols next to the title of each procedure

More information

Technical Supplement

Technical Supplement HA -6400 Côrt Home Automation System Setup Guide SUMMARY Technical Supplement The following supplemental instructions will provide a repeatable best practices in setting up the Côr Home Automation system.

More information

User s Guide. SUB-MA7240O-0001.OG.Solution doc. Created: 6/05/03. Last Updated: 23/09/03. MA7240AO-0001 Version 1.0

User s Guide. SUB-MA7240O-0001.OG.Solution doc. Created: 6/05/03. Last Updated: 23/09/03. MA7240AO-0001 Version 1.0 User s Guide SUB-MA7240O-0001.OG.Solution40-111.doc Created: 6/05/03 Last Updated: 23/09/03 MA7240AO-0001 Version 1.0 2 Table Of Contents User List...6 Quick Reference..7 Features...7 Keypad User's Guide...8

More information

Avigilon Control Center System Integration Guide

Avigilon Control Center System Integration Guide Avigilon Control Center System Integration Guide with Picture Perfect 4 INT-PP4-A-Rev1 Copyright 2012 Avigilon. All rights reserved. No copying, distribution, publication, modification, or incorporation

More information

7:00AM 1:00AM ET 7:00 AM 12:00AM ET

7:00AM 1:00AM ET 7:00 AM 12:00AM ET Agent Guide Homebase intouch Customer Service (877) NRT-HELP Help@HomebaseinTouch.com M-F: 7:00AM 1:00AM ET Weekends: 7:00 AM 12:00AM ET Version 1.1 October 2012 Contents What is Homebase intouch?... 4

More information

Telecare User Guidance

Telecare User Guidance Summary Telecare User Guidance This guidance describes; what Telecare is and how it may assist you, how you can apply for Telecare, if you are eligible and how much it may cost, how it is installed, how

More information

Staff Alert Panel. Installation Guide. Using the Touchpad Exit Controller B

Staff Alert Panel. Installation Guide. Using the Touchpad Exit Controller B Staff Alert Panel Using the Touchpad Exit Controller Installation Guide 3125 North 126th Street, Brookfield, WI 53005 phone: 800.669.9946 fax: 262.790.1784 www.rft.com 2015 RF Technologies, Inc. All specifications

More information

QUICK CONSUMER REFERENCE GUIDE

QUICK CONSUMER REFERENCE GUIDE QUICK CONSUMER REFERENCE GUIDE Your System: ADT Smart Home Keyholder Response Starting to use the Keypad, ADT Smart Home App and web portal PM360 Alarm Panel Keypad KeyFob ADT Smart Home ADT Smart Home

More information

Avigilon Control Center 5 System Integration Guide

Avigilon Control Center 5 System Integration Guide Avigilon Control Center 5 System Integration Guide with Hirsch Velocity INT-HIRSCH-B-Rev1 2012 2014 Avigilon Corporation. All rights reserved. Unless expressly granted in writing, no license is granted

More information

Avigilon Control Center 5 System Integration Guide

Avigilon Control Center 5 System Integration Guide Avigilon Control Center 5 System Integration Guide with Lenel Facility Commander Wnx INT-FCWNX-A-Rev1 2010 2014 Avigilon Corporation. All rights reserved. Unless expressly granted in writing, no license

More information

i-vu CCN 4.0 Owner s Guide

i-vu CCN 4.0 Owner s Guide i-vu CCN 4.0 Owner s Guide CARRIER CORPORAION 2007 A member of the United echnologies Corporation family. Stock symbol UX. 11-808-377-01 07/07 able of Contents ACCESSING YOUR SYSEM... 3 YOUR SYSEM DEAILS...

More information

Wander Management Solutions

Wander Management Solutions Wander Management Solutions A secure environment is crucial to your residents and their families. If your residents are at risk of Wander, keep them safe while reducing the risk of elopements, injuries

More information

USER GUIDE WIRE-FREE HOME PROTECTION SYSTEM AG100+ CONTENTS

USER GUIDE WIRE-FREE HOME PROTECTION SYSTEM AG100+ CONTENTS CONTENTS USER GUIDE WIRE-FREE HOME PROTECTION SYSTEM AG00 Section Getting started. General system overview. Introduction to the system. Items included with the system. Introduction to the Smart Panel.5

More information

BOSCH GV4 Alarm Panel

BOSCH GV4 Alarm Panel System Galaxy Quick Guide CONFIGURATION AND OPERATION BOSCH GV4 Alarm Panel SG 10.2 (or later) NOV 2012 This is a Galaxy Product Interface Guide. Information in this document is subject to change without

More information

SK642 THE TELEPHONE DIALER REQUIRES A LAND TELEPHONE LINE TO MAKE OUTGOING CALLS AND ELECTRICITY.

SK642 THE TELEPHONE DIALER REQUIRES A LAND TELEPHONE LINE TO MAKE OUTGOING CALLS AND ELECTRICITY. SK642 WIRELESS WATER ALARM SYSTEM WITH AUTO DIALER OWNER'S MANUAL AND SET UP INSTRUCTIONS. Thank you for choosing Ideal Security s Wireless Water Alarm with Telephone Dialer. Please read through complete

More information

CompleteView SightLogix Sensor Setup Manual. CompleteView Version 4.7.1

CompleteView SightLogix Sensor Setup Manual. CompleteView Version 4.7.1 CompleteView SightLogix Sensor Setup Manual CompleteView Version 4.7.1 Table of Contents Contents Introduction... 3 Setup the SightLogix Sensor s Video in CompleteView... 4 Configuring the SightLogix Sensor

More information

BeneVision Central Monitoring System. Quick Reference Guide

BeneVision Central Monitoring System. Quick Reference Guide BeneVision Central Monitoring System Quick Reference Guide NOTE: The Quick Reference Guide is not intended as a replacement to the Operating Instructions. Prior to operating equipment, the user must be

More information

Proudly Designed and Manufactured in New Zealand. By Arrowhead Alarm Products Ltd

Proudly Designed and Manufactured in New Zealand. By Arrowhead Alarm Products Ltd Proudly Designed and Manufactured in New Zealand By Arrowhead Alarm Products Ltd ARMED = Indicates the System is Armed in Away Mode. STAY = Indicates the System is Armed in Stay Mode. BYPASS = When Flashing,

More information

Avigilon System Integration Guide. for the Avigilon Control Center and Access Control Manager

Avigilon System Integration Guide. for the Avigilon Control Center and Access Control Manager Avigilon System Integration Guide for the Avigilon Control Center and Access Control Manager 2014-2017, Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, ACC, AVIGILON CONTROL CENTER,

More information

User Guide ecobee ecobee 477 Richmond St West 2nd Floor, Toronto Ontario M5V 3E7 Canada Toll free

User Guide ecobee ecobee 477 Richmond St West 2nd Floor, Toronto Ontario M5V 3E7 Canada Toll free User Guide ecobee3 2014 ecobee 477 Richmond St West 2nd Floor, Toronto Ontario M5V 3E7 Canada Toll free 1.877.932.6233 www.ecobee.com e3-ug-r001 1 Table of Contents Overview... 4 Getting Help... 4 Touch

More information