VIBRATION TRANSMITTER MODEL 140T INSTALLATION The mounting orientation can be in any position. This position should be in an area for the best vibrati
|
|
- Jonathan Campbell
- 5 years ago
- Views:
Transcription
1 VIBRATION TRANSMITTER MODEL 140T A lowcost, yet highly accurate and rugged vibration transmitter, the Model 140T is ideal for use with all machines, even those which previously may have been considered uneconomical to monitor. The unit easily mounts by use of a standard 1/420 stud. The Model 140T is a twowire, looppowered transmitter which can feed the vibration level of your operating machinery to a data logger, milliamp monitor or process control computer. Solidstate accelerometer and circuit design provide a signal proportional to vibration velocity. Intrinsically safe, it can safely be used in hazardous environments when coupled with a Model MTL7206 Instrinsic Safety Barrier. Reliable performance Easy to install signal compatible with most BAS controllers Intrinsically safe Class I Division 1, Groups A,B,C; Class II Division 1 Groups E, F, G 2year warranty APPLICATION Vibration monitoring can help alert you to the destructive effects vibration has on mechanical system equipment such as: air handler fans cooling tower fans pumps compressors Vibration range Model 140T1 Model 140T2 Frequency range Supply voltage (Vs) Maximum load resistance Output, proportional to vibration level 0 to 1 in/sec 0 to 2 in/sec 7 Hz to 1300 Hz ±3% (420 to 78,000 rpm) 12 to 50 VDC, unregulated; black=negative, red=positive, with reverse voltage protection RL = 50 (Vs12) ohms 600Ω at 24 VDC DIMENSIONS in (cm) (0.95) 1.75 (4.44) (3.33) dia 1" NPT (2.86) Mounting connection 1/ (0.95) deep Isolation 500V, circuittocase Conduit connection 1" MNPT Temp range 4 to 185 F (20 to 85 C) Environment rating NEMA 4, weatherproof Case Cadmiumplated steel Mounting 1/4''20 stud Weight 1.4 lb (0.64 kg)
2 VIBRATION TRANSMITTER MODEL 140T INSTALLATION The mounting orientation can be in any position. This position should be in an area for the best vibration signal definition or where there is a good transfer of the machine's (fan s, pump s, etc.) vibrations. The best location will vary from machine to machine. The location of the transmitter should be selected carefully. When selecting the site for the mounting location, it is helpful to survey the site with the aid of a vibration meter. Wiring subject to physical damage should be adequately protected. When installing electrical conduit, it is recommended that a short length (12") of flexible conduit be used between the transmitter and an associated junction box. This construction will provide some vibration isolation in the conduit line. Conduit and fittings should conform to the environment of the transmitter location. Weatherresistant or raintight fittings should be used to protect the transmitter wiring from a humid or corrosive atmosphere. Make all connections in accordance with national and local codes. 140T Maximum Cable C=0.08 µf L= 4.0 mh hazardous area 140T safe area MODEL RANGE 140T1 0 to 1 in/sec 140T2 0 to 2 in/sec 6 5 MTL7206 IS BARRIER Ground Here Only SIGNAL Standard Wiring Intrinsically Safe Wiring 1250 VDC Power 2035 VDC Power SIGNAL CAUTION: You must ensure that the transmitter is rigidly attached to the monitoring point for the proper sensing of the vibration. NOTE: Each application should be evaluated on an individual basis. Consult equipment manufacturers for specific details concerning safe vibration levels.
3 WEATHER INSTRUMENTS A70 SERIES The A70 Series sensors with signal conditioning, provide a output proportional to wind speed (A70SL), wind direction (A70DL), barometric pressure (A70PL) or rainfall (A70RL). The A70 Series provides the user with weather information that can be used for monitoring purposes or as an input to control systems. Rugged construction Reliable operation Industry standard output Track mounted transmitter WIND SPEED (A70SL) The wind speed is measured with a three cup anemometer and a output signal proportional to 0100 mph is generated. Accuracy from 39 mph is /1 mph. Above 10 mph, accuracy is / 5% of reading. The A70SL is supplied with 60 feet of cable and a 10 inch stub mast for mounting the anemometer. WIND DIRECTION (A70DL) Wind direction is measured with a precision potentiometric wind vane which produces a signal proportional to the azimuth of the wind. This signal is converted to a output over The vane has a 4 degree deadband on either side of north. The A70DL is provided with 60 feet of cable and an S mast for mounting. BAROMETRIC PRESSURE (A70PL) The A70PL senses barometric pressure by an integrated silicon, absolute pressure sensor with integral temperature compensation, and outputs a signal over 27'' to 31'' Hg. Accuracy is /0.05'' Hg. The sensor is mounted to the transmitter board. A 3/16'' tube may be attached to the sensor to provide remote pressure sensing. RAINFALL (A70RL) The A70RL utilizes tipping bucket technology to measure rainfall and output a signal over a range of 01''. When the output reaches 20 ma (1'') it resets to 4 ma and the cycle begins over. Accuracy is /4%. The sensor includes 50 feet of cable.
4 WEATHER INSTRUMENTS A70 SERIES COMMON Operating power 1224 VDC 30 ma max Output 4 20 ma Maximum loop resistance (operating voltage 10) x 50 ohms 700Ω at 24 VDC Signal conditioner accuracy ±1% MODEL A70SL A70DL A70PL A70SDL A70SDPL A70RL WIND SPEED ANEMOMETER X3 24 VDC POWER SUPPLY A70SL WIND SPEED X VDC POWER SUPPLY A70PL BAROMETRIC PRESSURE Signal Signal 24 VDC POWER SUPPLY 24 VDC POWER SUPPLY Red Dot Center Terminal Rain Gauge X4 2 1 A70RL 1 2 X1 Wind Speed Transmitter Wind Direction Transmitter Barometric Pressure Transmitter Wind Speed / Direction Transmitters Wind Speed / Direction and Barometric Pressure Transmitters Rainfall Transmitter WIND DIRECTION VANE X No Polarity A70DL Signal WIND DIRECTION RAINFALL Signal MODEL A76T10 A96100P A96200P Optional Equipment Tripod Tower with Mast (10' high total) for wind speed and direction sensors Lighting Arrestor for wind speed sensor Lighting Arrestor for wind direction sensor
5 ALPHASONIC LEVEL PROBE ALP SERIES The ALP Series alphasonic level probe functions on the ultrasonic principle and provides reliable liquid level measurement with automatic temperature compensation. The continuous output is not influenced by changing liquid conductivity or dielectric values. Since the ALP Series operates on the ultrasonic principle, performance is not affected by foam or dirty liquids, and it may be used on all liquids compatible with PVC and polypropylene. The enclosure is NEMA 4X (IP65) rated. Continuous level probe with output Automatic temperature compensation Probe may be cut to length and easily field calibrated NEMA 4X enclosure All plastic construction Suitable for a wide variety of liquids Not affected by foam, dirty liquids, etc. Range Accuracy Resolution Pulse rate Supply voltage Signal output Max loop resistance Temperature rating Temp. Compensation Pressure rating Pipe material Enclosure rating Enclosure material Mounting threads Conduit connection Thread material 0.3 to 10 feet ± 1% of span 0.125'' (0.3 cm) 5 per second 1236 VDC 600Ω at 24 VDC 4 to 140 F (20 to 60 C) Automatic over entire range Atmospheric PVC standard NEMA 4X / IP65 Polypropylene 1'' NPT 1/2'' NPT Polypropylene ALP shown with optional bracket DIMENSIONS in (cm) 4.9 (15.0) 3.7 (11.9) 3.2 (10.7) Length 120'' (305 cm) max 1.0 (2.5) 2.8 (7.1) 1" NPT
6 ALPHASONIC LEVEL PROBE ALP SERIES () PWR Level Probe CALIBRATION SPAN INVERT* ON OFF 24 VDC Power Supply Signal The ALP Level Probe is factory calibrated to read 4 ma at the bottom of the pipe and 20 ma two inches from the bottom of the threads. The pipe may be cut and the ALP recalibrated per the following instructions. Installation of a longer pipe in the field is not recommended. 1. Connect a multimeter in series to read the ma output of the ALP. 2. Set the Invert switch to OFF. 3. Set level to lowest point. A cup of liquid or a piece of tape over the end of the pipe may be used as a substitution for a low level reading. 4. Turn SPAN pot until the signal reads 4 ma. Turning the pot counterclockwise will lower the ma signal and turning the pot clockwise will increase the ma signal. 5. The ALP is now calibrated. If the ALP is required to output 20 ma when the level is at the bottom of the pipe, turn the Invert switch to ON and adjust the pot until 20 ma is read. 6. Remove the liquid or tape. ALP * The ALP Level Probe is shipped factory calibrated with 4 ma set at the end of the pipe and 20 ma set 2 inches below the tip of the threads. To reverse the setting for 20 ma at the end of the pipe, set the invert switch to the ON position. MOUNTING Alphasonic Level Probe Sensor Length* (inches) XXX 18, 24, 36, 48, 60, 72, 84, 96, 108, 120 Optional Bracket No bracket B Bracket ALP Side Mounting Option "B" Option Side mount bracket ; ;; CAUTION: Avoid installing the ALP Level Probe near a source of vibrations or loud repetitive noise, such as a motor. Remove and insert the ALP Level Probe slowly. Rapid removal or insertion may cause excessive back pressure in the pipe and rupture the diaphragm. ALP 18 B Example: 18" Alphasonic Level Probe output with mounting bracket *For special lengths, contact Kele
7 WATER DETECTOR MODEL WD1B A Kele Company TM The WD1B Water Detector features goldplated probes and microchip technology for dependable detection of conductive liquids. The WD1B can be operated from 11 to 27 volts AC or DC. For application flexibility, SPDT contacts are provided to connect to a monitoring system. A height adjustable, cast aluminum, weatherproof enclosure is standard. A green LED visible outside the box indicates power. A red LED indicates water detected. The WD1B is also available with an external tape style sensor, the WD1BT. Weatherproof enclosure Easy to install SPDT alarm contacts 11 to 27 VAC or VDC Reliable operation LED's for power and alarm indication Adjustable detection level OPERATION The WD1B can be used with any contactclosure monitoring panel. The SPDT contacts may be wired NormallyOpen or NormallyClosed, allowing wiring flexibility to handle most installations. MOUNTING Secure by applying a silicone adhesive to the mounting feet, and placing the sensor in the area to be protected. For more permanent installations, fasten the sensor using the 0.19" holes provided in the mounting feet with #6 or #8 screws. The legs are adjustable (1.5") for precise water level signaling. Power requirements Power consumption Operating temp Enclosure Alarm output 11 to 27 VAC or VDC DC: 10mA typical, 30mA max AC: 30mA typical, 70mA max 32 to 158 F (0 to 70 C) Cast aluminum, weatherproof with adjustable legs SPDT contacts rated, 1 24 VAC/VDC, 1/2 120 VAC DIMENSIONS in (cm) 0.12" (0.32) 2.0" (5.08) 0.31 (0.79) MAX. 1.8" (4.57) MIN. 0.20" (0.51) 2.75" (6.99) 3.75" (9.53 ) RED WHT GASKETED SS COVER 1/2" FNPT CONDUIT CONNECTION Probe height adjustable 01.5" (03.8 cm) Input Voltage 11 to 27 VAC/VDC WD1B 1.75" (4.45) 4.5" (11.43) MOUNTING HOLES 0.187" DIA (0.47) YEL ORN BLU SPDT alarm contacts LED WINDOW The WD1B Water Detector is provided with a 1/2" FNPT conduit connection in the end of the enclosure. Terminations are made to the colorcoded wires with fieldsupplied connectors. All interconnect wiring should be 18 AWG or larger. If grounded AC power is used, the grounded power supply lead must be connected to the white lead on the WD1B, or the unit may fail to operate. WD1B Water Detector WD1BT RELATED PRODUCTS Water Detector (Tape Style Sensor)
8 WATER DETECTOR (TAPE STYLE) MODEL WD1BT A Kele Company TM The WD1BT Tape Style Water Detector includes all the standard features of the WD1B, plus a selfadhesive sensor tape with copper electrodes and a durable cotton cover for dependable detection of conductive liquids anywhere along the length of the tape. SPDT contacts make on moisture detection, and release when dry. Weatherproof enclosure, power LED (green), alarm LED (red) are standard. Weatherproof enclosure SPDT alarm contacts Ultra reliable operation Power and alarm LED s Standard sensor tape lengths 10, 25, 50 Tape may be cut to length in field OPERATION The WD1BT can be used with any contactclosure monitoring device, wiring to either the normallyopen or normallyclosed contacts for flexibility. Power requirements Power consumption Operating temp Enclosure Alarm output Sensor tape Sensor electrodes Weight INSTALLATION 11 to 27 VAC or VDC DC: 10mA typical, 30mA max AC: 30mA typical, 70mA max 32 to 158 F (0 to 70 C) Cast aluminum, weatherproof SPDT, 1 24 VAC/VDC, 1/2 120 VAC 0.1" H x 1.5" W (0.25 cm x 3.81 cm) 3 mil copper, 1/4" gap (0.08 mm, 0.64 cm gap) WD1BT lb (0.8 kg) WD1BT lb (1.0 kg) WD1BT lb (1.4 kg) Mount the WD1BT box adjacent to the area to be protected. Unroll the sensor tape, remove vinyl release layer from the back, and hand press onto a surface that is dry and free of all debris and dust. Check that screw terminal on the end of the tape is connected to the SJOW cord securely. Test by shorting the screw terminals or the electrodes at the end of the tape. Note: Once the sensor is activated (wet), the contacts will remain in alarm until the cotton cover is completely dry. DIMENSIONS in (cm) 0.12" (0.32) 2.0" (5.08) 0.31 (0.79) 1.8" (4.57) 2.75" (6.99) 3.75" (9.53 ) GASKETED SS COVER 1/2" FNPT CONDUIT CONNECTION 1.75" (4.45) 4.5" (11.43) MOUNTING HOLES 0.187" DIA (0.47) LED WINDOW The WD1BT Water Detector is provided with a 1/2" FNPT conduit connection in the end of the enclosure. Terminations are made to the colorcoded wires with fieldsupplied connectors. All interconnect wiring should be 18 AWG or larger. Input Voltage 11 to 27 VAC/VDC RED WHT WD1BT YEL ORN BLU SPDT alarm contacts If grounded AC power is used, the grounded power supply lead must be connected to the white lead on the WD1BT, or the unit may fail to operate. WD1BT10 WD1BT25 WD1BT50 Water detector with 10 (3.05 m) sensor tape Water detector with 25 (7.62 m) sensor tape Water detector with 50 (15.24 m) sensor tape
9 WATER SENSOR / SWTICH MODEL LD124 The LD124 is a small electronic control relay for detecting a rising water level. It has a mediumpower relay inside its waterproof enclosure, which is operated by water reaching the trip level, and can be used to control alarms or other equipment. The relay is normally energized when the power supply is switched on and no water is present. When water rises up the side of the box to reach the switching level, the relay drops out. This sequence is failsafe, allowing the LD124 to be used as a water spillage alarm switch, or to turn off a valve or stop an air conditioning unit before the water overflows its containment. Small enough to be used in restricted spaces Water detection with accurate switching level All components safely encapsulated against moisture ingress Switching capability 5 amps at 240 volts AC Power supply Input power Switchoff height Switchon (reset) level Output relay rating INSTALLATION / MOUNTING 24 VAC, 50/60 Hz 30% / 10% Approx. 1 W 0.43'' (1.1 cm) nominal 0.31'' (0.8 cm) nominal 240 V, 50/60 Hz, 5A 24 VDC, 2.5A A piece of double sided tape is fitted to the base of the LD124 and can be used to fix it to the surface being protected. Clean the mounting surface thoroughly to insure good adhesion. Pull off the protective paper covering and press the LD124 down into position. DIMENSIONS in (cm) Red Sleeve (Power) 1 1/4'' (3.1) Red Supply Red 24 VAC 50/60 Hz A Kele Company Black Sleeve (Relay) Basic Connections LD124 Mauve Pink 2'' (5.0) 7/8'' (3.2) Trip Level 0.43'' (1.1) Reset Level 0.32'' (0.8) Grey NOTE: Relay contacts shown in ALARM (or poweroff) condition. Isolated Switch Output N/O N/C COM WARNING: Although the LD124 is totally encapsulated and is resistant to water ingress when used as intended (to detect rising water levels) it should not be installed where the encapsulated surface is permanently under water. TM LD124 Water Sensor / Switch
10 FLOAT SWITCHES L4 / L8 / F7 SERIES The Model L4 float switch is a heavy duty explosion proof switch for the most critical applications. Explosion proof construction Stainless steel float Magnetically actuated Good for specific gravities 0.7 and up CE, CSA and UL listed 1 1/2 NPT mounting Class I, Division 1, Groups C, D Class II, Division 1, Groups E, F, G The Model L8 is an excellent lower cost general purpose float switch. It is magnetically actuated for long life and decreased maintenance, with a high resistance to chemicals. UL recognized and CE approved Polyphenylene sulfide float Magnetically actuated Good for specific gravities 0.6 and up 1 NPT mounting The Model F7BT and the Model F7SS are economical solutions to smaller vertical mount float switch applications. The F7 BT includes a cork float and the F7SS includes a stainless steel float. Low cost Simple installation Vertical 1/8" NPT mount Temperature limits 275 F Operating Pressure 100 psig (690 kpa) Electrical rating 10A@125/250 VAC Installation Horizontal Dimensions 19 5/32"L (48.7cm) Weight 3.2 lb (1.5 kg) Approvals UL listed, CSA, CE Temperature limits 212 F Operating Pressure 150 psig (1000 kpa) Electrical rating 5A@125/250 VAC Installation Horizontal Dimensions 8 5/16"L (21.1cm) Weight 0.4 lb (0.2 kg) Approvals UL recognized, CE Dependable Magnetically actuated F7BT F7SS Temperature limits 220 F (105 C) 300 F (149 C) Operating Pressure 150 psig (1000 kpa) 450 psig (3100 kpa) Electrical rating AC: 25VA, 1A, 200 V AC: 30W 0.14 A, 220 V DC: 0.28A/24 V or 0.7A/120 V DC:10W, 1 A, 200 V Installation Vertical Vertical Dimensions 2.18"H x 1.18 dia. (5.54 cm x 30 cm) 2.06"H x 1" dia.(52.3 cm x 25.4 cm) Weight 0.1 lb (0.04 kg) 0.2 lb (0.1 kg) Approvals UL recognized UL recognized
Instruction Manual Model A
706 Bostwick Avenue, Bridgeport, CT 06605 TEL: 203-368-6751 FAX: 203-368-3747 1-800-566-6822 www.devarinc.com Instruction Manual Model 18-232A LOOP POWERED ALARM MANUAL NO. 990029 MODEL 18-232A LOOP POWERED
More informationDIGITAL METERS Large Display Temperature Meters Instruction Manual
DIGITAL METERS Large Display Temperature Meters PD755 PD756 PD757 Handles Thermocouple & RTD Inputs with Simplicity J, K, T, E, R, & S Thermocouples 100 Ω Platinum RTD (0.00385 or 0.00392 curve) Large
More informationINTRODUCTION / TABLE OF CONTENTS
1 2 INTRODUCTION / TABLE OF CONTENTS Step One Offered in liquid and gas sensor types, the general purpose flow switch provides reliable low or no flow detection of relatively clean, non coating media with
More informationTop-quality products that are always in stock. Level
Top-quality products that are always in stock. Level MADE IN USA NEW Products manufactured in the United States Products that are new to the catalog /SERIES PAGE Leak Detection AQS00660, AQS00661, LD1-24
More informationSensors & Accessories Compatible with ENVIROMUX-2D/5D/16D ENVIROMUX
Sensors & Accessories Compatible with ENVIOMUX-2D/5D/16D ENVIOMUX Temperature & Humidity Sensors Probe-Style Temperature & Combination Sensor Temperature Sensor (ENVIOMUX-STSM-E7) Applications from -4
More informationSensors & Accessories Compatible with ENVIROMUX-2D/5D/16D ENVIROMUX
ENVIOMUX Temperature & Humidity Sensors Probe-Style Temperature & Combination Sensor ENVIOMUX-STSM-E7 ENVIOMUX-STHSM-E7 Temperature Sensor ENVIOMUX-STS Low-Cost Industrial Precision Temperature/Humidity
More informationINSTALLATION, OPERATION INSTRUCTIONS FOR FLOW SWITCHES 62-9FS & FS
THERMAL INSTRUMENT Co. 217 Sterner Mill Road, Trevose, PA 19053 Telephone No. (215) 355-8400 Fax No. (215) 355-1789 Email: office@thermalinstrument.com INSTALLATION, OPERATION INSTRUCTIONS FOR FLOW SWITCHES
More informationSensall Sapphire. Thermo MeasureTech ULTRASONIC POINT LEVEL SYSTEM
ULTRASONIC POINT LEVEL SYSTEM Introduction Compliance with growing government regulations mandates tighter level controls with advanced diagnostics to avoid releases, overspills and costly environmental
More informationUltrasonic Point Level Switches
see more at SORInc.com Request Quote Ultrasonic Point Level Switches Ultrasonic point level switches are a cost-effective solution for your applications. Installation requires mounting the sensor (threaded
More informationPump-Up Controller MODEL 4062
Pump-Up Controller 4-20mA Input/Scalable Output Seal Fail Monitoring Duplex Pump Alternation Hand-Off-Auto Controls Dual Run-time Meters RS-485/Modbus Communications DESCRIPTION The Model 4062 Pump-Up
More informationvibration switch
user manual 440-450 vibration switch INSTALLATION - OPERATION - MAINTENANCE Z0592822_A ISSUED 06/2017 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. contents Section 1 -
More informationSapphire ULTRASONIC POINT LEVEL SYSTEM
ULTRASONIC POINT LEVEL SYSTEM Introduction Compliance with growing government regulations mandates tighter level controls with advanced diagnostics to avoid releases, overspills and costly environmental
More informationIntrinsically Safe Pressure Transmitters for installation in hazardous locations Models IS-20-S, IS-21-S, IS-20-F, IS-21-F WIKA Datasheet IS-20
Electronic Pressure Measurement Intrinsically Safe Pressure Transmitters for installation in hazardous locations Models IS-20-S, IS-21-S, IS-20-F, IS-21-F WIKA Datasheet IS-20 Applications Chemical, Petrochemical
More informationElectronic Flow Switches
Industries Electronic Flow Switches Petrochemical Refining Oil Production Water Treatment Pharmaceutical Food and Beverage Pulp and Paper Power Production Gas Processing Mining Biotechnology Semiconductor
More informationImprove Performance and Reduce Maintenance Costs. Model Q45D. Dissolved Oxygen Monitor...
Improve Performance and Reduce Maintenance Costs Model Q45D Dissolved Oxygen Monitor... Why Throw Away Money? Why Throw Away Money? ATI s Model Q45D Dissolved Oxygen monitor is designed to provide reliable
More informationPump-Down Controller MODEL 4052
Pump-Down Controller 4-20mA Input/Scalable Output Seal Fail Monitoring Duplex Pump Alternation Hand-Off-Auto Controls Dual Run-time Meters RS-485/Modbus Communications DESCRIPTION The Model 4052 Pump-Down
More informationUltrasonic Switches. Features & Benefits
Why use an ultrasonic switch over other level technologies? Depending upon your application, there may be three or four technologies equally suited for your application; however; only one will be the best
More informationUser's Manual: Series 260A Model 260A Process Current Loop-Powered Alarm
User's Manual: Series 260A Model 260A Process Current Loop-Powered Alarm Table of Contents Page Introduction 1 Description 1 Specifications 2 Installation 3 Calibration 4 General Maintenance 5 List of
More informationMAINTENANCE & TROUBLESHOOTING GUIDE LEAK ALARM CHANNEL DRY OIL WATER AUX ALARM HIGH LOW CRITICAL WATER TANK LEVEL ALARM MODEL LDE-740 ADVANCE PAPER
PNEUMERCATOR Liquid Level Control Systems Electronic Systems Excluding LC2000 And TMS Series MAINTENANCE & TROUBLESHOOTING GUIDE 400 300 500 FUEL LEVEL LEAK MONITOR 1 200 600 OIL/GAS NORMAL WATER PNEUMERCATOR
More informationIntroduction to Flow Switch
Introduction to TM Solutions Flow Detection, Switching & Control Flow switches detect a change in state from flow or no-flow within pipe or ducting. Correspondingly, the sensor inverts a contact to signal
More informationROYCE SUSPENDED SOLIDS SYSTEM MODEL 7011A AND SENSORS MODELS 72A, 72P, 73B, 74A, 75A & 76A
SPECIFICATIONS (Revised 1/12/2006) ROYCE SUSPENDED SOLIDS SYSTEM MODEL 7011A AND SENSORS MODELS 72A, 72P, 73B, 74A, 75A & 76A The system shall operate on the principle of light absorption. It shall consist
More informationWater Leak Detector. Installation and Troubleshooting. Overview
Overview Water Leak Detector The Water Leak Detector is designed to sense the presence of water and alert a central monitoring system of the potentially destructive situation. Upon water detection, an
More informationDräger Polytron 5100 EC Detection of toxic gases and vapors
Dräger Polytron 5100 EC Detection of toxic gases and vapors The Dräger Polytron 5100 EC is a cost-effective explosion proof transmitter for the detection of toxic gases or oxygen. It uses a high performance
More informationNitrogen Dioxide (NO2) Single-Point Gas Detection System
Nitrogen Dioxide (NO) Single-Point Gas Detection System DESCRIPTION Wall-mounted gas monitor with built-in nitrogen dioxide (NO)/diesel fume gas sensor, accepts one analog remote device such as a secondary
More informationINTRODUCTION / TABLE OF CONTENTS
1 2 INTRODUCTI / TABLE OF CTENTS Step One The LVCN 51 Series Continuous Relay Controller is a general purpose level controller which provides single tank level indication with dual relays and a repeater
More informationT500 Elite - Hotbus Plant Wide Monitoring System for Bucket Elevators & Conveyors
Plant Wide Monitoring System for Bucket Elevators & Conveyors APPLICATION Combined belt alignment, belt speed, continuous bearing temperature, pulley alignment, level and plug condition monitor for bucket
More informationAnalog Room Pressure Monitor RPC Series
Description The Room Pressure Monitor is used to measure differential pressure in the range of 0.125 to 1"wc or 30 to 250 Pa. It combines precision high sensitivity silicon sensing capabilities and the
More informationCAPITAL CONTROLS SERIES WP70CV3 GAS FEEDERS
CAPITAL CONTROLS SERIES WP70CV3 GAS FEEDERS The Capital Controls Series WP70CV3 gas feeders are wall panel mounted and vacuum operated. Easy to install, each Series WP70CV3 wall panel feeder is factory
More informationRonan Model X90 Series Point Level Monitor
Ronan Model X90 Series Point Level Monitor For more than 27 years Ronan has provided the process control industry with unsurpassed products in the harshest environments. With a philosophy of designing
More informationWH EN IGH T T C LO SED
AR EA kajdfkjl; lkjdflkjal; ldkfj;alk alskjdf ;lsdkf 7079 ph/orp Transmitter 70-82-03-08 1/97 Page 1 of 5 Specification Overview The 7079 ph/orp Transmitter is designed for chemical process industry applications
More informationRamsey Series Motion Monitoring Systems Accurate Sensing of Speed Conditions on Rotating Shafts and Machinery
Ramsey Series 60-200 Motion Monitoring Systems Accurate Sensing of Speed Conditions on Rotating Shafts and Machinery Ramsey Series 60-200 Motion Monitoring Systems offer versatile and reliable packages
More informationModel Q45P/R. ph/orp Monitor...
Model Q45P/R ph/orp Monitor... Sensor Mounting Configurations The Differential Difference ORP Monitor ATI's versatile Q45P/R ph/orp system is designed for use in all industrial and municipal applications.
More informationRamsey Motion Monitoring Systems
Ramsey Motion Monitoring Systems 60-200 Motion Monitoring Accurate Sensing of Underspeed, Overspeed and Zero Speed Conditions on Rotating Shafts and Machinery The Ramsey Series 60-200 Motion Monitoring
More informationOxygen (O2) Single-Point Gas Detection System
Oxygen (O) Single-Point Gas Detection System DESCRIPTION Wall-mounted gas monitor with built-in oxygen (O) sensor, accepts one analog remote device such as a secondary gas sensor, temperature or humidity
More informationULTRA-SAFE Explosion-proof Duct Heaters
Standard Construction Heat Exchanger has copper tubes with integral aluminum fins. Each unit undergoes hydrostatic testing at 350 psig, five times the pressure relief valve setting of 70 psig. Heat Transfer
More informationRK Hydrogen Sulfide Transmitter Operator s Manual
65-2331RK Hydrogen Sulfide Transmitter Operator s Manual Part Number: 71-0176RK Revision: B Released: 11/26/14 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction
More informationDSD-3 DIFFERENTIAL SPEED DETECTOR
DSD-3 DIFFERENTIAL SPEED DETECTOR Instruction Manual PL-207 June 1993 PROCESS MEASUREMENTS 33452070 ABOUT THIS MANUAL This manual covers the installation and operation of the DSD-3. It is essential that
More informationInstrumentation and Controls Group
Instrumentation and Controls Group Jerguson Gage and Valve is the leading supplier of level gaging products, offering the world s largest selection of liquid level gage glasses, magnetic gages, and accessories.
More informationPage. 1-2 Sepra-Lite Integral Optic Level Switches. 3-5 Electro Optic Level Systems: Probe and Controller
Order from: C A Briggs Company 622 Mary Street; Suite 101; Warminster, PA 18974 Phone: 267-673-8117-800-352-6265; Fax: 267-673-8118 Sales@cabriggs.com - www.cabriggs.com Page 1-2 Sepra-Lite Integral Optic
More informationCabinet Cooler Systems
Cooler Systems Cooler Systems Stop electronic control downtime due to heat, dirt, and moisture! maintain NEMA 4, 4X, and 12 integrity. All are and compliant! What is an EXAIR Cooler System? A low cost,
More informationCentro-Matic Automated Lubrication Systems System Controls
Selecting the right controls for your automated lubrication system is one of the last steps in the design process. Several different models may be chosen to control power-operated pumps, depending on the
More informationBrooks MT3600 Series Metal Tube Variable Area Flowmeters
Data Sheet Flanged, NPT or socket-welded connections 10% full scale accuracy Disassembly for cleaning without removal from the process line Standard direct reading, detachable scales Permanent magnetic
More informationHigh Pressure Conductivity Monitor
Product Data Sheet PDS 71-EDS880/1/rev.A August 2006 Model EDS880/1 High Pressure Conductivity Monitor COMPLETE SYSTEM FOR THE DETERMINATION OF CONDUCTIVITY IN HIGH PRESSURE SYSTEMS SENSOR INSTALLS DIRECTLY
More informationSitron s CF Line of Flow Switch Monitors
Sitron s CF Line of Flow Switch Monitors Models: CF 12AC CF 12DC CF 420 F 420 RCF 420 Introduction Sitron s versatile and intelligent line of Thermal Dispersion Flow Switch Monitors are compact switches,
More informationModel Q45P/R. ph/orp Monitor...
Model Q45P/R ph/orp Monitor... Sensor Mounting Configurations The Differential Difference ORP Monitor ATI's versatile Q45P/R ph/orp system is designed for use in all industrial and municipal applications.
More informationINSTRUMENTATION AND CONTROL DEVICES FOR HVAC
PART 1 GENERAL 1.01 RELATED REQUIREMENTS SECTION 23 0913 INSTRUMENTATION AND CONTROL DEVICES FOR HVAC A. Section 26 2717 - Equipment Wiring: Electrical characteristics and wiring connections. 1.02 ADMINISTRATIVE
More informationINSTALLATION INSTRUCTIONS
Loop Alarm Model SC1490 and SCL1490 INSTALLATION INSTRUCTIONS LOVE LOVE CONTROLS a Division of Dwyer Instruments, Incorporated PO Box 338 Michigan City, IN 46361-0338 (800) 828-4588 (219) 879-8000 FAX
More informationTemperature Controllers
Model TEC-4100 1/4 DIN Model TEC-4100 1/4 DIN Temperature Controller Ordering Code: Power Input BOX 1 4 = 90-250 VAC 5 = 11-26 VAC / VDC TEC-4100- Configurable for 4 Programmable Outputs and NEMA 4X/IP65
More informationDAF DETECT-A-FIRE. DAF DETECT-A-FIRE Detection and Release Devices
DAF DETECT-A-FIRE DAF DETECT-A-FIRE Detection and Release Devices FEATURES Repeatable - resets itself, nothing to replace, testable Rugged - withstands shock and vibration Versatile - offers various temperature
More informationCapital Controls SERIES 70CV3000 CHLOROMATIC VALVE
Capital Controls SERIES 70CV3000 CHLOROMATIC VALVE Integrated Gas Control Valve with Integral Controller The Series 70CV3000 Chloromatic Intelligent Gas Flow Control Valve is designed to control chemical
More informationRK-05 Combustible Gas Transmitter Operator s Manual
65-2405RK-05 Combustible Gas Transmitter Operator s Manual Part Number: 71-0180RK Revision: 0 Released: 2/16/11 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction
More informationInductive Conductivity
Inductive Conductivity THORNTON Leading Pure Water Analytics 7100E Non-Fouling Sensors PEEK or PFA Wetted Parts Excellent Chemical Resistance 0/4 to 20mA Outputs for Conductivity & Tempreature 4 Relays
More informationDräger Polytron 5100 EC Detection of toxic gases and vapors
Dräger Polytron 5100 EC Detection of toxic gases and vapors The Dräger Polytron 5100 EC is a cost-effective explosion proof transmitter for the detection of toxic gases or oxygen It uses a high performance
More informationTable of Contents. Protective Relays
Table of Contents KILOVAC WD Series, DIN Rail or Screw Mounted Introduction..........................................................11-2 KILOVAC WD25 Paralleling Relays........................................11-3
More informationMODEL: O ELECTROCHEMICAL O2 DETECTOR (Used with ST1400 O2 Sensor) Part Number: MAN Rev. 0
MODEL: O2-25-24 ASSEMBLY CONSISTS OF: XP-O2 housing (supersedes PE-EX-O2) ST1400-500-24 sensor (supersedes PE1400-500-24) JB2 junction box CB2 connector board ELECTROCHEMICAL O2 DETECTOR (Used with ST1400
More informationDescription. Applications
CVEP PDS CVEP Convection for Hazardous Heater For Locations Hazardous Locations Convection Heater 1.8 to 9.0kW (T-2A) 280 C (536 F) 1.6 to 4.0kW (T-3A) 180 C (356 F) 1.8 to 9.0kW (T-2) 1.8 300 C to 9.0kW
More informationBelt Conveyor Safety Monitoring Devices
ISO-00:000 certified Belt Conveyor Safety Monitoring Devices More than just another level measurement company. Aplus Finetek Sensor, Inc. SRT CONVEYOR BELT MISALIGNMENT SWITCH PRODUCT INTRODUCTION The
More informationSeries 155. Mass Flow Computers TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS Mass Flow Computers Series 155 The Kurz 155 Mass Flow Computer is a versatile system transmitter that integrates the functions of flow and temperature measurement, flow totalization,
More informationThermo Scientific Ramsey TM Series Sensing Speed Conditions on Rotating Shafts and Machinery
Thermo Scientific Ramsey TM Series 60-200 Sensing Speed Conditions on Rotating Shafts and Machinery The Thermo Scientific Ramsey Series 60-200 monitors under-speed, overspeed and zero-speed conditions
More informationSpecifications - Installation and Operating Instructions 2X 1/2 NPT OR M20 ELECTRICAL ENTRY. 3/4 NPT or 3/4 BSPT 5/8 [15.88]
Series PMT2 Particulate Transmitter Specifications - Installation and Operating Instructions Bulletin PC-PMT2 2X 1/2 NPT OR M20 ELECTRICAL ENTRY THREADED MOUNT Probe A Length in [mm] 3 3 [76.20] 5 5 [127.00]
More informationDräger Polytron Fixed Gas Detector. Dräger Polytron 5700 Infrared DrägerSensor PIR 7000 to detect combustible gases and vapors
Dräger Polytron 5700 Fixed Gas Detector Dräger Polytron 5700 Infrared DrägerSensor PIR 7000 to detect combustible gases and vapors Dräger Polytron 5700 Including e-box for increased safety wiring The Dräger
More informationph COOLING TOWER CONTROLLER
LAKEWOOD INSTRUMENTS MODEL 350 ph COOLING TOWER CONTROLLER INSTRUCTION MANUAL SERIAL #: Lakewood Instruments 7838 North Faulkner Road, Milwaukee, WI 53224 USA Phone (800) 228-0839 Fax (414) 355-3508 http://www.lakewoodinstruments.com
More informationSingle Point Freeze Protection Heat Trace Control TRACON MODEL FPT 130 Installation and Operation Manual
We manage heat MANUAL Single Point Freeze Protection Heat Trace Control TRACON MODEL FPT 130 Installation and Operation Manual 1850 N Sheridan Street South Bend, Indiana 46628 (574) 233-1202 or (800) 234-4239
More informationDETECT-A-FIRE Heat Detectors
DETECT-A-FIRE Heat Detectors DETECT-A-FIRE thermal detectors are detection and release devices used for fire detection systems to activate alarms and actuate extinguishing systems. This rate compensated
More informationCAUTION WARNING INSTALLATION INSTRUCTIONS FOR HEALTHY CLIMATE WHOLE HOME DEHUMIDIFIER MODEL HCWH-065 (Y3013) DEHUMIDIFIERS
DEHUMIDIFIERS 506451-01 04/2012 HEALTHY CLIMATE WHOLE HOME DEHUMIDIFIER INSTALLATION INSTRUCTIONS FOR HEALTHY CLIMATE WHOLE HOME DEHUMIDIFIER MODEL HCWH-065 (Y3013) FRONT VIEW (with alternate outlet location
More informationModus Model DA General Eastern Low Differential Pressure Alarm Controller
GE Sensing & Inspection Technologies Modus Model DA General Eastern Low Differential Alarm Controller The Modus Model DA is a controller designed for the monitoring of low differential pressures. It combines
More informationIsco 3700ZR Sampler. Manual Set
Isco 3700ZR Sampler Manual Set Assembly #60-2744-045 Copyright 2001. All rights reserved, Teledyne Isco Revision D, December 14, 2012 This set of manuals supports the Isco 3700ZR Refrigerated Sampler.
More informationModel A-5. Low Range Wet/Wet Differential Pressure Transducer DESCRIPTION FEATURES
Low Range Wet/Wet Differential Pressure Transducer DESCRIPTION The Model A-5 low range wet/wet differential pressure transducer offers a stainless steel assembly. The Model A-5 line pressure zero shift
More informationDurafet II and Meredian II Combination ph/orp Electrodes for Honeywell 7777 Mountings Series 7777 Specifications
Durafet II and Meredian II Combination ph/orp Electrodes for Honeywell 7777 Mountings Series 7777 Specifications 70-82-03-06 July 2004 Overview Honeywell s 7777 Series of electrode mountings enables an
More informationSAPCON SMART-SSI. Continuous Speed Indicator. Users Manual. . Introduction. . General Description. . Principle of Operation. .
CALIB CONTINUOUS SPEED INDICATOR EVALUATION UNIT ALRM 1 ALRM 2 ALRM 3 PULSE DISPLAY MESSAGES INSTRUMENT START/RESTART OVERSPEED OCCURED > UNDERSPEED OCCURED < SPEED IS
More informationThermostats type KPU REFRIGERATION AND AIR CONDITIONING. Technical leaflet
Thermostats type KPU REFRIGERATION AND AIR CONDITIONING Technical leaflet Contents Page Introduction... 3 Features... 3 Approvals... 3 Technical data... 3 Regulating ranges... 4 Ordering... 4 Contact systems...
More informationU5300 Industrial Pressure Transducer
FEATURES Heavy Industrial CE Approval 10 V/m EMI Protection Reverse Polarity Protection on Input Short Circuit Protection on Output ±0.1% Accuracy ±0.5% Total Error Band Compact Outline -40 C to +125 C
More informationSoftware Version 2.01 LEVEL MONITOR MODEL 220
Software Version 2.01 LEVEL MONITOR MODEL 220 19 April 2000 CONTENTS 1. Introduction 1 1.1 Model Number Designation 2 1.2 Intrinsic Safety Considerations 3 2. Specification 4 3. Operation 6 3.1 Display
More informationInstallation and Operating Instructions
The Leader of RF and Sonic Level For Assistance Call 1-800-527-6297 Outside North America 1-215-674-1234 Installation and Operating Instructions Series 504-1200 Ultrasonic VeriGAP Switch using 404-1200
More informationMODEL FPT-130 SINGLE POINT FREEZE PROTECTION HEAT TRACE CONTROL
TRACON MODEL FPT-130 SINGLE POINT FREEZE PROTECTION HEAT TRACE CONTROL TABLE OF CONTENTS FPT 130 Overview... 2 Installation... 3 Power Source and Load Connections... 4 Temperature Sensor... 5 External
More informationMSM400 Ultrasonic Suspended Solids Monitoring and Control System
Product Data Sheet MSM400 Ultrasonic Suspended Solids Monitoring and Control System Continuous sludge discharge monitor for up to 50% suspended solid The MSM400 system contains a control unit and either
More informationANCHOR BOLT DETAIL. Non-Shrink Grout. Poured In Place, After Equipment Setting. "L" Type Anchor Bolt Carbon Steel AISI 304 S.S.
ANCHOR BOLT DETAIL Heavy Flat Washer Heavy Hex Nut UNC Th'd Mounting Flange Of Equipment To Be Mounted C B A D Non-Shrink Grout. Poured In Place, After Equipment Setting. Heavy Flat Washer Heavy Hex Nut
More informationThermo Flo With Compact Junction Box AT17, AT18, AG17 & AG18 Series Manual
Thermo Flo With Compact Junction Box AT17, AT18, AG17 & AG18 Series Manual Flowline Inc. 10500 Humbolt Street Los Alamitos, CA 90720 Tel: (562) 598 3015 Fax: (562) 431 8507 www.flowline.com Rev A MN301480
More informationDuct and Rough Service Carbon Monoxide Sensor
Product Identification and Overview Duct and Rough Service Carbon Monoxide Sensor BAPI s Carbon Monoxide Sensor offers enhanced electrochemical sensing with outstanding accuracy at low concentrations.
More informationLow Temperature Zirconia Oxygen Analyzer
Data Sheet SS/ZDT FG Issue 10 Low Temperature Zirconia Oxygen Analyzer ZDT FG Environmental certification MCERTS SIRA certificate MC99000 1/00 User-friendly language options selectable system alarms comprehensive
More informationDräger Polytron 5700 IR Detection of flammable gases and vapours
Dräger Polytron 5700 IR Detection of flammable gases and vapours The Dräger Polytron 5700 IR is a cost effective explosion-proof transmitter for the detection of flammable gases in the lower explosive
More informationRK Multi Point Detector Operator s Manual
65-2480RK Multi Point Detector Operator s Manual Part Number: 71-0198RK Revision: C Released: 11/26/14 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction manual before
More informationM2 Transmitter Operator s Manual
M2 Transmitter Operator s Manual Part Number: 71-0107RK Revision: D Released: 10/7/10 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction manual before operating instrument.
More informationPublic Safety DAS Annunciator Panel
Public Safety DAS Annunciator Panel 120 VAC Models: 1221-A, 1221-B, 1221-C Revision D 91117 48 VDC Models: 1221-A-48, 1221-B-48, 1221-C-48 24 VDC Models: 1221A-24, 1221-B-24, 1221-C-24 CAUTION: (Read This
More informationAlarmLine Addressable Linear Heat Detector
Line Addressable Linear Heat Detector P/N 7-0001-00 Effective: March 2008 K-7-02 FEATURES UL Listed FM Approved CSFM MEA (pending) Low-cost interface between Line sensor cable and control panel accepting
More informationOperating Instructions
CS101 CarSense Vehicle Motion Detector Operating Instructions CAUTIONS AND WARNINGS Never use the CS101 as a safety reversing or presence detection system. The CS101 requires that a vehicle be moving for
More informationDSGH. Radiation-Based Detector with GEN2000 Electronics for Density Measurement QUICK REFERENCE GUIDE
DSGH Radiation-Based Detector with GEN2000 Electronics for Density Measurement QUICK REFERENCE GUIDE Revision History Revision History Version of manual Description Date 1.0 Initial release 051025 1.1
More informationRK-02 Multi Point Detector Operator s Manual
65-2485RK-02 Multi Point Detector Operator s Manual Part Number: 71-0237RK Revision: A Released: 11/26/14 RKI Instruments, Inc. www.rkiinstruments.com WARNING Read and understand this instruction manual
More informationAS570 Chill-Out Combination Sensor Installation and Operating Instructions
AS570 Chill-Out Combination Sensor Installation and Operating Instructions Tel: 763. 571.3121 Fax: 763. 571.0927 www.minco.com Description: Model AS570 is a combination sensor, which includes a low-temperature
More informationModels TX-KE and TX-KP Toxic Gas Transmitters
Models TX-KE and TX-KP Toxic Gas Transmitters Instruction Manual PureAire Monitoring Systems, Inc. 557 Capital Dr. Lake Zurich, IL. 60047 Phone: 847-726-6000 Fax: 847-726-6051 Toll-Free: 888-788-8050 www.pureairemonitoring.com
More informationINTRODUCTION / TABLE OF CONTENTS
1 2 INTRODUCTION / TABLE OF CONTENTS Step One The LVCN 20 and LVCN 100 Series are general purpose level controllers offered in two configurations for pump and valve control. The LVCN 100 Series features
More informationTwo-Channel Gas Controller
Two-Channel Gas Controller Specifications subject to change without notice. USA 09 Page of DESCRIPTION Highly configurable, UL 0 performance-tested and -certified, and wall-mounted gas monitor; continuously
More informationULTRA-SAFE Explosion-proof Duct Heaters
Standard Construction Heat Exchanger has copper tubes with integral aluminum fins. Each unit undergoes hydrostatic testing at 350 psig, five times the pressure relief valve setting of 70 psig. Heat Transfer
More informationMotogard. Over Temperature Protection System. Installation Instructions
Motogard Over Temperature Protection System Installation Instructions Motogard General Information Motogard Over-Temperature Protection Systems provide immediate overheating protection for: motors, equipment
More informationM5200 Industrial Pressure Transducer
SPECIFICATIONS Wide Temperature Range Compact Variety of Pressure Ports and Electrical Configurations Optional Stainless Steel Snubber CE Compliant and Weatherproof UL Certified Gage, Sealed, Compound
More informationExplosion Proof Light Watt Metal Halide - Class 1 Div 1 & Class 2 Div 1
Explosion Proof Light - 400 Watt Metal Halide - Class 1 Div 1 & Class 2 Div 1 Part #: EPL-HB-400W-MH Made in the USA The EPL-HB-400W-MH metal halide, hazardous area light fixture from Larson Electronics
More informationABB Instrumentation. Specifications. COMMANDER 150 Universal Process Indicator. the 1 /8 DIN indicator to match all your display requirements
Specifications COMMANDER 150 Universal Process Indicator High visibility 6-digit LED display the clearest view of your process status 0.1% measurement accuracy precise indication of process measurement
More informationThermo-Flo Flow Switches FT10 and GT10 Series Owner s Manual
Warranty, Service & Repair To register your product with the manufacturer, go to the Flowline website for on-line registration. The website address is as follows: www.flowline.com On-line Warranty Registration
More informationWFDE Series Waterflow Detector
WFDE Series Waterflow Detector The System Sensor WFDE series is compatible with pipe diameters ranging from 50mm through 200mm and can be mounted in a vertical or horizontal position. Features Compliant
More informationANNUNCIATOR INSTRUMENTS Model PD141AFO Instruction Manual
ANNUNCIATOR INSTRUMENTS Model PD141AFO Instruction Manual From urgent alarms to routine messages, the PD141AFO VIGILANTE handles all types of operational messages with simplicity and economy. The VIGILANTE
More information