385 SERIES REMOTE HANDHELD SIREN ETSA385HR

Transcription

1 ! WARNING Sirens produce loud sounds that may damage hearing: - Roll up windows. - Wear hearing protection. - Use only for emergency response. - Avoid exposure to siren sound outside of vehicle. Please see back page for Technical Specifications Amplifi er Microphone, Lights and Siren Controller IMPORTANT NOTICE TO INSTALLER: Make sure to read and understand all instructions and warnings before proceeding with the installation of this product. Ensure all warning cards are delivered to the end user of this equipment. Introduction The is a Remote vhandheld Controlled Siren Amplifi er designed for 100 Watt speaker use. The siren comes standard with integrated noise-cancelling microphone for PA use. The amplifi er box contains an amplifi er capable of supplying sound to a single 100 Watt speaker. The also includes 3 switches and 6 independently controlled accessory switches each capable of supplying amps. The primary operating modes are Tone, Radio, PA, Horn, Horn Override, and a push button Manual Override are available in all modes. Sirens provide an essential function of an effective audio / visual warning system. However, sirens are only short range secondary devices. The use of a siren does not insure that all drivers can or will abide by or react to an emergency warning signal, especially at high rates of speeds or long distances. The operator of the vehicle must never take the right of way for granted and it is the operator s responsibility to proceed safely. The effectiveness of this siren system is highly dependant on the correct mounting and wiring. The installer must read and follow the manufacturer s installation instructions and warnings in this manual. The vehicle operator should verify the siren system is securely fastened to the vehicle and properly functioning. Effective sirens generate loud sound pressure levels that can potentially cause hearing damage. Installers and those around the vehicle need to be aware of the dangers and wear hearing protection whenever the siren system is operating. Vehicle operators and occupants should assess their exposure to siren noise and determine what steps need to be taken to prevent hearing damage. The siren system is intended for use by authorized personnel only. It is the user s responsibility to ensure they understand and operate the emergency warning devices in compliance with all applicable city, state, and federal laws and regulations. SoundOff Signal assumes no liability for any loss resulting from the use of the siren system. Package Contents: 1 ea. Amplifi er Box 1 ea. Handheld Controller 1 ea. Cradle with Mounting Hardware 4 ea. Amplifi er Wire Harnesses with Connectors (1-4 pin, 1-12 pin, 1-5 pin and 1-14 pin) 1 ea. Instruction Manual 1 ea. Operators Warning Card to remain in vehicle for operator review 1 ea. Sound Pressure Warning Label that is to be attached in vehicle and in plain site of operator and occupants of the vehicle 1 ea. Label Card for Aux. Switches Wire capacity requirements for siren amplifi er (incoming power) each supply and ground wire Feet: 14 AWG Feet: 12 AWG Feet: 10 AWG 30+ Feet: Consult Factory to determine requirements Important Information: Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website at and select the Warranty & Returns link along the left column of our home page. If you have questions regarding this product please contact Technical Services, Monday - Friday, 8 am to 5 pm at , press #4 to skip the automated message. Questions or comments that do not require immediate attention may be ed to techsupport@soundoffsignal.com / / Thank you for trusting us with your safety! 10.10

2 WHITE VIOLET GREY GREEN BLACK GREEN/WHITE - Push Button #5 Output - Push Button #6 Output - Relay #9 Output for 2 wire Arrow Control Interface Horn Ring In (WHITE/BLACK) Horn Ring Out (WHITE) FUNCTION **RELAY X RELAY #9 OFF OFF OFF LEFT ARROW ON OFF RIGHT ARROW OFF ON CENTER OUT ARROW ON ON **Relay 'X' is the relay associated with the push button programmed for arrow control. (ie. Button 1 is set up for Arrow control, then Relay 1 is Relay 'X') Auxiliary VIOLET Backlight GRAY 4 RJ-45 Jumper Cable Level 3 Output YELLOW GREEN 10 amp Level 2 Output Level 1 Output 50A 50A - Push Button #1 Output - Push Button #2 Output - Push Button #3 Output - Push Button #4 Output Right Alley - for Single Button Alley Light Control BROWN YELLOW ORANGE /WHITE GREEN/BLACK /BLACK Cable to control panel IGNITION 10 amp 3 amp RADIO REBROADCAST NEUTRAL SAFETY SWITCH BLACK ORANGE/BLACK YELLOW PARK KILL ORANGE ORANGE/BLACK 11 Ohm Speaker 100 Watt RADIO REBROADCAST OUPUT LEVEL ADJUST Note: All fuses shown are user supplied & must be installed to ensure safe operation. PARK KILL WILL DEACTIVATE -AUX AND HORN RING WILL NOT REACTIVATE ONLY YELP, WAIL OR TONE BUTTONS WILL REACTIVATE 10.10

3 LEGEND: ON = Programming Modes Auxiliary Button Programming: 1. Press and Hold Auxiliary Button #1 and #6 until Level 1 LED Flashes. 2. Press the auxiliary button which setting is going to be viewed/ changed. 3. Monitor the Arrow/Alley LED s to determine setting for Auxiliary Button Toggle ON/OFF Momentary ON 8 Second Delay Left Arrow Right Arrow Center Out - Arrow Alley Left Alley Right Single Button Arrow Single Button Alley 4. Press and release Auxiliary Button until desired mode is selected. 5. Continue steps 2-4 for any other Auxiliary Buttons needing to be programmed. 6. When fi nished, momentarily depress Radio Rebroadcast (RR) Button to exit programming mode. Slide Switch Mode: 1. Press and Hold Auxiliary Button #1 and #4 until Level 2 LED fl ashes. 2. Press Auxiliary switch 1, 2, or 3 depending on required mode of operation. Aux 1: Progressive 1,2,3 Level 1 selected: Active Outputs: 1 Level 2 selected: Active Outputs: 1,2 Level 3 selected: Active Outputs: 1,2,3 Aux: 2 Progressive 1,2,3 with option to turn off lower levels Level 1 selected: Active Outputs: 1 Level 2 selected: Active Outputs: 1,2 (Level 1 may be turned OFF) Level 3 selected: Active Outputs: 1,2,3 (Level 1 and 2 may be turned OFF) Aux 3: Individual 1,2,3 Level 1 selected: Active Outputs: 1 Level 2 selected: Active Outputs: 2 Level 3 selected: Active Outputs: 3 3. When fi nished, momentarily depress Radio Rebroadcast (RR) Input Settings: 1. Press and Hold Auxiliary Button #1 and #3 until LEVEL #3 LED fl ashes. a. Park Kill Polarity Mode b. Horn Ring Polarity Mode c. Level 3 Tone Activation ON = Activate when input connected to Gnd OFF = Activate when input connected to +V ON = Activate when input connected to Gnd OFF = Activate when input connected to +V ON = Siren Tone is always enabled OFF = Siren Tone is enabled whenever in position 3 d. 8 Second level / Aux Switch Buzzer Alert ON = Enabled - Buzzer will sound whenever level switch is not Off or Aux switches are On OFF = Disabled 2. When fi nished, momentarily depress Radio Rebroadcast (RR) Denotes Factory Default Setting 10.10

4 Other Modes: 1. Press and Hold Auxiliary Button #1 and #5 until LEVEL #1 and LEVEL #3 LED fl ashes. a. Horn Ring Activation OFF = Enabled whenever siren is in the ON position. Horn Ring Program: 1. Press and Hold Auxiliary Button #3 and #4 until Ø LED fl ashes. 2. Press Auxiliary Buttons depending on the required settings a. Horn Ring Scroll LEVEL Switches (1,2,3 with indicators) b. Buzzer ON = Enabled only when leve 3 is activated. ON = Enabled b. Hands Free Mode ON = Horn Ring will scroll through tones OFF = Horn Ring will cycle between 2 tones (hands free mode must be enabled) Ø OFF = Disabled ON = Hands Free Mode MASTER ON / OFF (Siren Standby) c. Park Latch ON = Park Kill Latches, requiring operator reset. OFF = Park Kill resets when connection is removed c. Horn Ring Standby Tone OFF = Standard ON = Air Horn Tone OFF = Warning Tone Control LEDs d. Off Delay d. Horn Ring Timeout ON = Siren will operate w/ ignition input OFF ON = Horn Ring has 8 second Timeout AUXILLARY BUTTON #s SPEAKER 1 LED DIAGNOSTIC LED e. Auxiliary Input LOW HIGH OFF = Siren will turn OFF when ignition input is OFF ON = Auxiliary Input activates Air Horn OFF = Auxiliary Input activates Tone 2. When fi nished, momentarily depress Radio Rebroadcast button to exit programming mode. Setting PA Volume: 1. Press and Hold Auxiliary Button #1 and #2 until LEVEL #2 and LEVEL #3 LED fl ashes. a. Depress and hold PA switch on microphone and press Pushbutton 1-6 depending on volume required. When correct volume is determined, press Radio Rebroadcast and the volume setting will be permanently stored. Denotes Factory Default Setting e. Alternate Horn Ring Control ALTERNATE HORN RING CONTROL OPTION 1 OPTION 2 STANDBY OEM HORN OEM HORN LEVEL 1 OEM HORN OEM HORN LEVEL 2 Air Horn or Wail Button Tone while Pressed (programmable) Tap to Turn On Warning Tone, Tap again to Change Warning Tone. Press and Hold for Air Horn Tone LEVEL 3 Tap to turn ON Warning Tone, Tap again to change Warning Tone. Press and Hold for Air Horn Tone OFF = Horn Ring will not Timeout ON = Enabled OFF = Disabled f. Alternate Horn Ring Control Option (Disabled if Alternate Horn Ring Control is not enabled. ON = Option 2 OFF = Option 1 3. Momentarily depress Radio Rebroadcast (RR) to exit programming mode TONE SWITCH OFF: Air Horn Tone or Wail Button Tone while Pressed TONE SWITCH ON: Tap to change Warning Tone, Press and Hold for Air Horn Tone 10.10

5 Tones Program: 1. Press and Hold Buttons #2 and #5 until Level 1, Level 2 and Level 3 LEDs fl ash. 2. Press button to program the tones (each press of the button will advance to next TONE mode). Note: in operation, each press of the button will scroll between the 3 programmed tones. 3. Mode LED: Siren Tone #1 PWR LED: Siren Tone #2 LED and PWR LED: Siren Tone #3 4. Press Auxiliary Buttons to get required tone Aux. Button: Tone OFF OFF OFF Disabled OFF OFF ON WAIL Tone OFF ON OFF YELP Tone OFF ON ON ALERT Tone ON OFF OFF PIERCER Tone ON OFF ON HiLo Tone ON ON OFF Super HiLo Tone ON ON ON Tone Scroll (Wail, Yelp, Alert, Piercer) 5. HORN Button Press Horn Button and SPEAKER 1 LED will turn ON Press Auxiliary Buttons to get required tone. Aux. Button: Tone OFF OFF OFF Horn 1 OFF OFF ON Horn 2 OFF ON OFF Horn 3 OFF ON ON Horn 4 6. MAN Button Press MAN Button and DIAGNOSTIC LED will turn ON Press Auxiliary Buttons to get required tone. Aux. Button: Tone OFF OFF OFF Wail (with Frequency Decrease) OFF OFF ON Wail (Immediate OFF when released) OFF ON OFF Yelp OFF ON ON Alert ON OFF OFF Piercer ON OFF ON HiLo ON ON OFF Super HiLo 7. When fi nished, momentarily depress Radio Rebroadcast (RR) Level Switch Mapping: 1. Press Auxiliary Buttons #4 and #5 until RR LED Flashes 2. Press Level 1,2, or 3 switch to select level to be programmed 3. Press Auxiliary Buttons #1-#6 as required. LED ON = function will turn ON when Level is active 4. Press siren button for desired tone to be generated for level Alley Left = Tone 1 Alley right = Tone 2 Alley Left and Right = Tone 3 5. When fi nished, momentarily depress Radio Rebroadcast (RR) Setting Backlight/Indicator LED Intensity: 1. Press and Hold Radio Rebroadcast (RR) Button. 2. Then press Aux Buttons 1-6 to select intensity. 1 = Low Intensity 2 = High Intensity 10.10

6 AUXILLARY AND LEVEL SWITCH LED INDICATORS: LED INDICATOR CONDITION OFF ON FLASHING RELAY OUTPUT IS OFF RELAY OUTPUT IS ON RELAY OUTPUT HAS A FAULT AMPLIFIER DIAGNOSTIC INDICATORS: LED SPEAKER 1 LED DIAGNOSTIC LED CONDITION FLASHING ON ON OVER-TEMPERATURE FLASHING OFF ON UNDER-VOLTAGE FLASHING ON OFF OVER-VOLTAGE FLASHING FLASHING - COMM FAULT - RELAY FLASHING - FLASHING COMM FAULT - AMP FLASHING FLASHING FLASHING COMM FAULT -RELAY AND AMP OFF - - STANDBY MODE ON ON - SPKR 1 IS ACTIVE ON FLASHING - SPKR 1 FAULT ON OFF - SPKR 1 IS NON-FUNCTIONING TECHNICAL SPECIFICATIONS Overall Dimensions: Handheld Controller: Amplifi er/relay: Input Voltage: 5.13 H x 2.5 W x 1.25 D 2.66 H x 8.67 W x 5.66 D 10-30Vdc (negative ground) Input Current: VDC (100W Speaker) Standby Current: Ignition ON: Ignition OFF: Audio Frequency: Output Power: Siren Frequency: High Voltage Protection: Low Voltage Shutdown: Operating Temperature: Boxed Weight: 500mA <20mA 200Hz - 10 khz + 3db 100W RMS MAX. (11 Ohm Speaker Impedance) 675Hz Hz Limits to 32V in Maximum Voltage <9.0V will cause siren output to cease and will resume when system voltage is >9.0V -40 C to +50 C 8 lbs Replacement Parts & Accessories: Microphone: Control Panel: PSRNMCØ2 PSRNCTRL