SECTION (16510) - INTERIOR LIGHTING

Transcription

1 SECTION (16510) - INTERIOR LIGHTING Note: This Section includes two (2) attachments. The second and third attachments contain the Light Fixture Matrix. PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Interior Lighting Fixtures 2. Lamps 3. Ballasts 4. Exit Signs 5. Emergency Lighting Units 6. Accessories B. Related Sections: 1. Section (09512) - Acoustical Tile Ceilings 2. Section (16050) - Common Work Results For Electrical. 3. Section (16520) - Exterior Lighting 4. Section (16580) - Lighting Accessories: For programmable lighting control systems, time switches, additional photoelectric relays, power relays, and contactors REFERENCES A. American National Standards Institute (ANSI) Publications: 1. C82.4 Ballasts for High Intensity Discharge and Low Pressure Sodium Lamps (Multiple-Supply Type) B. Institute of Electrical and Electronics Engineers, Inc. (IEEE) Publications: 1. C62.41 Surge Voltages in Low-Voltage AC Power Circuits C. Illuminating Engineering Society (IES) Publications: 1. LM-79 Approved Method: Electrical and Photometric Measurements of Solid-State Lighting Products 2. LM-80 Approved Method: Measuring Lumen Maintenance of LED Light Sources D. National Fire Protection Association (NFPA) Publications: 1. NFPA 70 "National Electric Code" 2. NFPA 101 Life Safety Code E. Underwriter's Laboratories, Inc. (UL) Publications: A Standard For Wire Connectors and Soldering Lugs for Use with Copper Conductors B Standard for Wire Connectors for Use with Aluminum Conductors Emergency Lighting and Power Equipment 1.03 SUBMITTALS A. General: Submit the following in accordance with Conditions of Contract and Division 01 Specification Sections. B. Submit Letter of Conformance in accordance with Section (01330) indicating specified items selected for use in project with the following supporting data. PAGE 1 FILE: a-CFRST-Interior Lighting REVISED: 06/06/ , Marriott International, Inc. CFRST SPECMSTR-NEW BUILD

2 REVISED: 06/06/16 1. For each type of lighting fixture indicated, arranged in order of fixture designation. Include data on features, accessories, and the following: a. Dimensions of fixtures. b. Certified results of laboratory tests for fixtures and lamps for photometric performance. c. Emergency lighting unit battery and charger. d. Fluorescent and high-intensity-discharge ballasts. e. Types of lamps. f. Photometric data. 2. Dimming Ballast Compatibility Certificates: Signed by manufacturer of ballast certifying that ballasts are compatible with dimming systems and equipment with which they are used. 3. Field Test Reports: Indicate and interpret test results for compliance with performance requirements. 4. Maintenance Data: For lighting fixtures to include in maintenance manuals specified in Division QUALITY ASSURANCE A. Fixtures, Emergency Lighting Units, and Accessories: Listed and labeled as defined in NFPA 70, Article 100, by a testing agency acceptable to authorities having jurisdiction. B. Comply with NFPA 70. C. NFPA 101 Compliance: Comply with visibility and luminance requirements for exit signs COORDINATION A. Fixtures, Mounting Hardware, and Trim: Coordinate layout and installation of lighting fixtures with ceiling system and other construction EXTRA MATERIALS A. Furnish extra materials described in Section (01790) Spare Parts and Materials that match products installed and that are packaged with protective covering for storage and identified with labels describing contents. PART 2 PRODUCTS Note: This Section includes two (2) attachments. The second and third attachments contain the Light Fixture Matrix MANUFACTURERS A. Avendra, LLC Preferred Manufacturers: 1. Subject to compliance with requirements, provide the products indicated for each designation in the Light Fixture Matrix attached at the end of this Section. a. None. B. Approved Manufacturers: 1. Subject to compliance with requirements, provide the products indicated for each designation in the Light Fixture Matrix attached at the end of this Section nd Avenue Design ( ) a. Contact: Jan Zanger ( ) 3. 3Form, Inc. ( ) a. Contact: Janice Eldredge ( ) 4. Acclaim Lighting, Los Angeles, CA ( ) 5. Ashley Lighting Inc. ( ) PAGE 2 FILE: a-CFRST-Interior Lighting Deleted: <#>Note: Include paragraphs below for use with CFRST LEED Volume Program. <#>CFRST LEED Volume Program Manufacturers: <#>Philips Lighting Company ( ) <#>Contractor shall furnish items identified as manufactured by Philips Group Brand Companies, as listed in the Light Fixture Matrix, from the Philips Group Brand Companies only. No substitutions will be approved. <#>Contact: Kathleen Kenny ( <#>Products: <#>Light Fixtures <#>Lamps Deleted: CFRST SPECMSTR-NEW BUILD 2016, Marriott International, Inc.

3 a. Contact: Laurie Foster ( ) 6. B-K Lighting a. Contact: Kahn Wright ( ) 7. Broan-NuTone LLC ( ) a. Contact: Ron Greene ( ) 8. Challenger Lighting Company ( ) a. Contact: Peggy Hart ( x 13) 9. Continental Group ( ) a. Contact: Sean Snyder ( ) 10. Cree LED Lighting Solutionsm ( ) a. Contact: Mark Wanless ( ) b. To obtain special volume pricing and accuracy for Marriott projects, contact: 1) Wiedenbach-Brown Co., Inc. Attn: Buck Buchanan ( ) or Christine Sturm ( x 353) 11. D Style, Inc. ( ) a. Contact: Jacob Shor ( x 118) 12. Eaton Cooper Lighting Business a. Contact: Kathleen Kenny ( ) 13. Electric Mirror LLC ( ) a. Contact: Doug Finefrock ( ) 14. ExceLine, a Philips Group Brand ( ) 15. Forecast, a Philips Group Brand ( ) 16. Hadco, a Philips Group Brand ( ) 17. InLight, a Unilight International Co, ( ) a. Contact: Patrice Adore ( ) 18. Insight Lighting Inc. ( ) a. Contact: Heather Reed ( ) 19. io LED Cooper Lighting ( ) 20. Kichler Lighting ( ) a. Contact: Peggy Hart ( x 13) 21. LBL Lighting, a Generation Brands Company ( ) a. Contact: Joe Krause ( ) 22. Lightolier, a Philips Group Brand ( ) 23. Lithonia Lighting, Accuity Brands, Inc. ( ) 24. Lumark Lighting, Division of Cooper Industries Company ( ) a. Contact: Mike Larkin ( x 239) 25. Lukas Lighting ( ) a. Contact: Craig Corona ( ) 26. LUMAPRO PAGE 3 FILE: a-CFRST-Interior Lighting REVISED: 06/06/ , Marriott International, Inc. CFRST SPECMSTR-NEW BUILD

4 REVISED: 06/06/ Lumiere, Division of Cooper Industries Company ( ) 28. iworks (LUDO Lamp) ( ) a. Contact: Michele Chan ( ) 29. Ledra, by Bruck Lighting Systems, Inc. ( ) 30. Lyte Poles Incorporated ( ) 31. MaxLite ( ) a. Contact: Bill Masi ( ) 32. National Specialty Lighting, Inc. ( ) 33. Pacific Coast Lighting ( ) a. Contact: Christopher Bryan ( ) 34. Panasonic ( ) a. Contact: Angy Steiner ( ) 35. Lithonia Lighting, Accuity Brands, Inc. ( ) 36. Philips Color Kinetics 37. Philips Lighting Company ( ) 38. Progress Lighting ( ) a. Contact: Rob Anderson ( ) 39. Project Light ( ) a. Contact: Sam Avny ( ) 40. Quoizel Lighting ( ) a. Contact: Hope Steen ( ) 41. Renaissance Lighting, Gotham Lighting, Accuity Brands, Inc. ( ) a. Contact: Troy Cook ( ) 42. Resolute, ( ) a. Contact: Holly Finn ( ) 43. RSA, a Cooper Lighting Brand ( ) 44. Scott Lamp Company ( ) a. Contact: Leanne Weber-Kreis ( ) 45. Stonco Lighting, a Philips Group Brand ( ) 46. TCP, Inc. ( ) a. Contact: Scott Carroll ( ) 47. Tech Lighting, a Generation Brands Company ( ) a. Contact: To obtain special volume pricing and accuracy for Marriott projects, contact: 1) Valley Lighting, Linthicum, MD ( ) 48. Translite Sonoma, a Philips Group Brand ( ) 49. Trend Lighting, a McFadden Lighting Company ( ) a. Contact: Rob Bruck ( ) PAGE 4 FILE: a-CFRST-Interior Lighting CFRST SPECMSTR-NEW BUILD 2016, Marriott International, Inc.

5 50. Trinity Lighting, Inc. ( ) a. Contact: Angie Allison ( ) 51. Van Teal, Inc. ( ) a. Contact: Joey Rogers ( ) 52. Wide-Lite, a Philips Group Brand ( ) 53. Approved Substitution FIXTURES AND FIXTURE COMPONENTS, GENERAL A. Metal Parts: Free from burrs, sharp corners, and edges. B. Sheet Metal Components: Steel, unless otherwise indicated. Form and support to prevent warping and sagging. C. Doors, Frames, and Other Internal Access: Smooth operating, free from light leakage under operating conditions, and arranged to permit re-lamping without use of tools. Arrange doors, frames, lenses, diffusers, and other pieces to prevent accidental falling during re-lamping and when secured in operating position. D. Reflecting Surfaces: Minimum reflectance as follows, unless otherwise indicated: 1. White Surfaces: 85 percent. 2. Specular Surfaces: 83 percent. 3. Diffusing Specular Surfaces: 75 percent. 4. Laminated Silver Metallized Film: 90 percent. E. Lenses, Diffusers, Covers, and Globes: 100 percent virgin acrylic plastic or annealed crystal glass, unless otherwise indicated. 1. Plastic: High resistance to yellowing and other changes due to aging, exposure to heat, and ultraviolet radiation. 2. Lens Thickness: inch minimum, unless greater thickness is indicated FLUORESCENT LAMP BALLASTS A. General Requirements: Unless otherwise indicated, features include the following: 1. Designed for type and quantity of lamps indicated at full light output. 2. Total Harmonic Distortion Rating: Less than 20 percent. 3. Sound Rating: A. B. Electronic Ballasts for Linear Lamps: Unless otherwise indicated, features include the following, besides those in "General Requirements" Paragraph above: 1. Certified Ballast Manufacturer Certification: Indicated by label. 2. Encapsulation: Without voids in potting compound. 3. Parallel Lamp Circuits: Multiple lamp ballasts connected to maintain full light output on surviving lamps if one or more lamps fail. C. Ballasts for Compact Lamps in Recessed Fixtures: Unless otherwise indicated, additional features include the following: 1. Type: Electronic fully encapsulated in potting compound. 2. Power Factor: 90 percent, minimum. 3. Operating Frequency: 20 khz or higher. 4. Flicker: Less than 5 percent. 5. Lamp Current Crest Factor: Less than Transient Protection: Comply with IEEE C62.41 for Category A1 locations. PAGE 5 FILE: a-CFRST-Interior Lighting REVISED: 06/06/ , Marriott International, Inc. CFRST SPECMSTR-NEW BUILD

6 D. Ballasts for Dimmer-Controlled Fixtures: Comply with general and fixture-related requirements above for electronic ballasts. 1. Compatibility: Certified by manufacturer for use with specific dimming system indicated for use with each dimming ballast. E. Ballasts for Low-Temperature Environments: As follows: 1. Temperatures 0 Deg F Above: Electronic or electromagnetic type rated for 0 deg F starting temperature. 2. Temperatures Minus 20 Deg F and Above: Electromagnetic type designed for use with high-output lamps HIGH-INTENSITY-DISCHARGE LAMP BALLASTS A. General: Comply with ANSI C82.4. Unless otherwise indicated, features include the following: 1. Type: Constant wattage autotransformer or regulating high-power-factor type, unless otherwise indicated. 2. Operating Voltage: Match system voltage. 3. Minimum Starting Temperature: Minus 22 deg F for single lamp ballasts. 4. Normal Ambient Operating Temperature: 104 deg F 5. Open-circuit operation that will not reduce average life. 6. Auxiliary, Instant-on, Quartz System: Automatically switches quartz lamp on when fixture is initially energized and when momentary power outages occur. Automatically turns quartz lamp off when high-intensity-discharge lamp reaches approximately 60 percent light output EXIT SIGNS A. General Requirements: Comply with UL 924 and the following: 1. Sign Colors and Lettering Size: Comply with authorities having jurisdiction. B. Internally Lighted Signs: As follows: 1. Lamps for AC Operation: Light-emitting diodes, 70,000 hours minimum rated lamp life. C. Self-Powered Exit Signs (Battery Type): Integral automatic charger in a self-contained power pack. 1. Battery: Sealed, maintenance-free, nickel-cadmium type with special warranty. 2. Charger: Fully automatic, solid-state type with sealed transfer relay. 3. Operation: Relay automatically energizes lamp from unit when circuit voltage drops to 80 percent of nominal or below. When normal voltage is restored, relay disconnects lamps, and battery is automatically recharged and floated on charger EMERGENCY LIGHTING UNITS A. General Requirements: Self-contained units. Comply with UL 924. Units include the following features: 1. Battery: Sealed, maintenance-free, lead-acid type with minimum 10-year nominal life and special warranty. 2. Charger: Fully automatic, solid-state type with sealed transfer relay. 3. Operation: Relay automatically turns lamp on when supply circuit voltage drops to 80 percent of nominal voltage or below. Lamp automatically disconnects from battery when voltage approaches deep-discharge level. When normal voltage is restored, relay disconnects lamps, and battery is automatically recharged and floated on charger. REVISED: 06/06/16 PAGE 6 FILE: a-CFRST-Interior Lighting CFRST SPECMSTR-NEW BUILD 2016, Marriott International, Inc.

7 4. Integral Time-Delay Relay: Arranged to hold unit on for fixed interval after restoring power after an outage. Provides adequate time delay to permit high-intensity-discharge lamps to restrike and develop adequate output LED FIXTURES A. Fixtures shall be UL or Intertek (ETL) Listed. B. Drivers shall be capable of accepting the voltage indicated on the [schedule] [drawings] and capable of dimming if required. The driver shall meet the following requirements: 1. Class A Sound Rating 2. Total Harmonic Distortion of less than 20 percent. 3. Operating temperature between -40 degree Celsius and 40 degrees Celsius. 4. Driver shall not contain any Polychlorinated Biphenyl (PCB). C. All LED fixtures shall be tested to IES LM-79 and IES LM-80 and meet the following: 1. Fixture Efficacy (Lumens per watt): 60 or greater. 2. Color Accuracy: Color Rendering Index (CRI): 70 or greater. 3. Light Color: As indicated on lighting fixture schedule. 4. Outdoor fixtures shall be IP65 Rated. 5. LEDs, driver and all components shall have a system lifetime of 50,000 hours or more at 25 degrees Celsius. 6. Fixture shall have a minimum of a five year warranty on all components and finishes LAMPS A. Fluorescent Color Temperature and Minimum Color-Rendering Index: 3500 K and 85 CRI, unless otherwise indicated. B. Non-compact Fluorescent Lamp Life: Rated average is 20,000 hours at 3 hours per start when used on rapid-start circuits. C. Metal-Halide Color Temperature and Minimum Color-Rendering Index: 3600 K and 70 CRI, unless otherwise indicated FIXTURE SUPPORT COMPONENTS A. Comply with Section 26/ (16050) "Basic Electrical Materials and Methods," for channel- and angle-iron supports and nonmetallic channel and angle supports. B. Single-Stem Hangers: 1/2-inch steel tubing with swivel ball fitting and ceiling canopy. Finish same as fixture. C. Twin-Stem Hangers: Two, 1/2-inch steel tubes with single canopy arranged to mount a single fixture. Finish same as fixture. D. Rod Hangers: 3/16-inch- minimum diameter, cadmium-plated, threaded steel rod. E. Hook Hangers: Integrated assembly matched to fixture and line voltage and equipped with threaded attachment, cord, and locking-type plug. F. Aircraft Cable Support: Use cable, anchorages, and intermediate supports recommended by fixture manufacturer FINISHES A. Fixtures: Manufacturer's standard, unless otherwise indicated. 1. Paint Finish: Applied over corrosion-resistant treatment or primer, free of defects. 2. Metallic Finish: Corrosion resistant. 3. Colors as indicated in Light Fixture Matrix. PAGE 7 FILE: a-CFRST-Interior Lighting REVISED: 06/06/ , Marriott International, Inc. CFRST SPECMSTR-NEW BUILD

8 PART 3 EXECUTION 3.01 INSTALLATION A. Fixtures: Set level, plumb, and square with ceiling and walls, and secure according to manufacturer's written instructions and approved submittal materials. Install lamps in each fixture. B. Support for Fixtures in or on Grid-Type Suspended Ceilings: 1. Recessed lighting fixtures shall be supported independently from the suspended ceiling system. Number 8 gauge galvanized steel wire or approved type hangers from the overhead building structures shall be provided for fixture support. C. Suspended Fixture Support: As follows: 1. Pendants and Rods: Where longer than 48 inches brace to limit swinging. 2. Stem-Mounted, Single-Unit Fixtures: Suspend with twin-stem hangers. 3. Continuous Rows: Suspend from cable installed according to fixture manufacturer's written instructions and details on Drawings CONNECTIONS A. Ground Equipment. 1. Tighten electrical connectors and terminals according to manufacturer's published torque-tightening values. If manufacturer's torque values are not indicated, use those specified in UL 486A and UL 486B FIELD QUALITY CONTROL A. Inspect each installed fixture for damage. Replace damaged fixtures and components. B. Advance Notice: Give dates and times for field tests. C. Provide instruments to make and record test results. D. Tests: As follows: 1. Verify normal operation of each fixture after installation. 2. Emergency Lighting: Interrupt electrical supply to demonstrate proper operation. REVISED: 06/06/16 3. Verify normal transfer to battery source and retransfer to normal. 4. Report results in writing. E. Malfunctioning Fixtures and Components: Replace or repair, then retest. Repeat procedure until units operate properly. F. Corrosive Fixtures: Replace during warranty period CLEANING AND ADJUSTING A. Clean fixtures internally and externally after installation. Use methods and materials recommended by manufacturer. B. Adjust aimable fixtures to provide required light intensities. Revision Log END OF SECTION PAGE 8 FILE: a-CFRST-Interior Lighting Comment [Comment1]: REVISION LOG: 08/17/01: Add Revision Log. 09/05/01: 2.01-Change Marketplace to Avendra, LLC. 09/20/01: 1.02-Revise/Clarify Text, Revise Paragraph Numbering. 12/30/05: Revised to 2006 Format 01/05/07: Updated to 2007 format 06/19/07: Added list of manufacturers and contacts. 09/28/07: Updated to 2007 Section Format. 04/01/09: Added Tech Lighting and updated Genlyte companies to Philips. 01/01/10: Updated contact person for all Philips Companies and Tech Lighting. 01/01/10: Moved GE, Philips and TCP from Avendra Approved to Approved Manufacturers. 01/01/10: Updated References. 06/01/10: Added Section for CFRST LEED Volume Program specifications. 01/01/11: Updated contact information. Added MaxLite, Neptun, and Cree LED Lighting Solutions as approved manufacturers. 09/03/12: Updated entire Section 09/03/12: Added Lukas Lighting as approved Manufacturer. 01/01/13: Updated manufacturer contact information. 01/06/14: Added LED Fixture specifications. 05/05/14: Updated manufacturer contact information. 12/01/15: Update manufacturer contact information 06/06/16: Updated Acclaim Lighting contact information. CFRST SPECMSTR-NEW BUILD 2016, Marriott International, Inc.