Premier External TD. Installation Manual INS352-3

Transcription

1 Premier External TD Installation Manual INS352-3

2 1. Accessing the Unit 1 2 Remove the top cap and loosen screw (screw retained in wall plate). Push up head unit and remove. 3 Use a flat head screwdriver to lever out both sides of the terminal cover as shown. 1 INS352-3

3 2. Choosing a Location Mounting height m (nominal 1.2m), measured to middle of unit. Mount perpendicular to ground. Parallel m Try to avoid direct sunlight. Avoid pointing at swaying bushes/trees and swaying clothes on a clothes line. Try to install the detector so its detection area is terminated by building/fences etc. This will reduce the effect of range variation caused by environmental changes. In the detection area try to avoid reflective surfaces such as standing water, swimming pools or polished floors as this can cause the detectors range or coverage to vary as reflected signals may be seen. INS

4 3. Mounting the Unit Front View WALL MOUNTING For wall mounting, the cable should be brought through the wall into the cable entry hole. Cable Entry REAR TAMPER To enable the rear tamper, the breakaway keyhole section must be securely fixed to the mounting surface. Cable Entry Cable Channels Rear View SURFACE WIRING For surface wiring, use the appropriate knockout in the top or bottom of the unit. If wiring from the top, use the knockouts in the top cap and run the cable down the cable channels and into the unit as shown. Knockout in Top Cap Cable Entry Conduit Entry 3 INS352-3

5 Pole Mount Bracket Mounting POLE MOUNTING Using the pole mount kit (available separately) the unit can be mounted on poles with an outside diameter of 20-57mm. Assemble the kit around the pole as shown and tighten the 4 bolts. Hook the detector wall plate onto the kit and secure the remaining 2 bolts through the lower mounting holes. 1 ø 20-44mm 2 x4 x1 ø 45-57mm x4 3 x3 5 4 INS

6 4. Wiring the Unit TERMINAL BLOCK 12V & 0V: 9-16 VDC. ALARM: NO/NC (selectable) relay output. 18 Ω, 50VDC, 10A Max. TAMPER: RLED: AUX: NC Relay output. 18 Ω, 50VDC, 10A Max. 0V: LED off. 12V or No Connection: LED on. NC relay input. NC = Normally Closed, NO = Normally Open JP1: Pulse Count /s JP2: Sensitivity HIGH MEDIUM LOW JP3: Alarm NC: alarm relay normally closed. NO: alarm relay normally open. 5 INS352-3

7 JP4: LED JP5: MODE Day/Night Mode Detector is always operating. Night Mode Detector only operates at night. JP6 & JP7: END OF LINE JUMPERS JP7 Selects the End-of-Line resistance. Equivalent to wiring a resistor of the selected value as shown. ALARM - JP7 JP6 Selects the resistance across the alarm relay. Equivalent to wiring a resistor of the selected value as shown. TAMPER - JP6 JP8 & JP9: see Auxiliary section (page 9) INS

8 5. Range Adjustment - PIR Bottom of head unit To adjust the range of the detector, rotate the circular section shown until the desired range is shown in the window. Note: Range can vary due to environmental conditions. To reduce the risk of false alarms always select the lowest range possible for the installation. Specified ranges are valid for nominal 1.2m mounting height. Selected Range Side View Position - 12m Coverage 1.2m 2m 4m 6m 8m 1 12m Position - 8m Coverage 1.2m 2m 4m 6m 8m 1 12m Position - 5m Coverage 1.2m 2m 4m 6m 8m 1 12m Position - 2m Coverage 1.2m 2m 4m 6m 8m 1 12m 7 INS352-3

9 6. Coverage Area Bottom of head unit Bottom of head unit Top View Top View 12m 1 8m 6m 4m 2m 2m 4m 6m 8m 1 12m 12m 1 8m 6m 4m 2m 2m 4m 6m 8m 1 12m 2m 4m 6m 8m 1 12m 2m 4m 6m 8m 1 12m Active detection coverage Active detection coverage Walk-testing With the range, sensitivity, coverage and pulse count set as desired, enable the LEDs and walk-through the area of protection. Confirm the LEDs light and alarm relay activates. INS

10 7. Auxiliary Input With the Auxiliary input enabled (JP8), a second detector with a normally closed relay output can be connected to the Premier External detector to give directional detection. The order of activation required to give an alarm signal is set by the direction jumper (JP9). When this is set to 1st the auxiliary detector must be activated first followed by the Premier External detector within 1 minute to give a valid alarm signal. With the jumper set to 2nd, the Premier External detector must be activated followed by the auxiliary detector within 1 minute. If directional detection is not required, disable the auxiliary input using JP8. JP8 ON OFF AUX Premier External PIR JP9 ALARM 1st NO ALARM NO ALARM 2nd JP9 AUX Premier External PIR 2nd ALARM 1st NO ALARM NO ALARM Regulatory Information Supplier: Texecom Ltd, St. Crispin Way, Haslingden, Lancashire, BB4 4PW, UK. Weee Directive: 2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: RoHs Directive: 2002/95/EC RoHS Compliant. Hereby, Texecom declares that this device does not contain lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated depheny ethers (PBDE) in more than the percentage specified by EU directive 2002/95/EC, except exemptions stated in EU directive 2002/95/EC annex. CE Directive: 2004/108/EC (CE directive): Hereby, Texecom declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC. Maintenance: Test yearly by the installer Warranty: 2 year replacement warranty Security grade: EN Grade 2 Environmental class: Class III Standards: EN Disclaimer: The Premier External TD is not a complete alarm system, but only its part. Therefore Texecom does not accept any responsibility or liability for any damage that is claimed to be a result of an incorrect functioning of the Premier External TD detector. Texecom reserves the right to change the specification without a prior notice. Certificate Number: FM MADE IN ENGLAND The Premier External detector is protected by UK & International Designs. Premier is a Trademark of Texecom Ltd. 9 INS352-3

11 8. Specifications Mounting Height: Supply Voltage: Current Drain (typical): Detection Method: Range: Alarm Output: Tamper Detection: Tamper Output: LED Indication: Environmental Protection: Waterproof Coating: EMC: m, 1.2m nominal 9-16 VDC 28mA Dual, non-overlapping, digital PIR 12m max. Adjustable to 8m, 5m and 2m NC/NO selectable relay. Rated 50VDC, 10A, 18Ω Wall and case. Sealed non-mechanical switch. NC relay. Rated 50VDC, 10A, 18Ω Red alarm indication IP65 Conformal EN : 1996, A1 1998, A EN 55022: Class B 9. Physical Specifications 89mm 86.5mm -35 C (-31 F) to +60 C (+140 F) 25m -35 C (-31 F) to +55 C (+131 F) 550g (20oz) approx. INS

12 Texecom Limited, Bradwood Court, St. Crispin Way, Haslingden, Lancashire BB4 4PW, England. Technical Support: UK Customers Tel: (Calls charged at 3.36 pence per minute from a BT landline. Calls from other networks may vary.) International Customers Tel: techsupport@texe.com Texecom Limited INS352-3 C