E N G L I S H FIRE ALARM ASPIRATION SENSING TECHNOLOGY QUICK INSTALLATION GUIDE STAND-ALONE FAAST LT MODELS FL0111E FL0112E FL0122E. 367 mm.

Size: px
Start display at page:

Download "E N G L I S H FIRE ALARM ASPIRATION SENSING TECHNOLOGY QUICK INSTALLATION GUIDE STAND-ALONE FAAST LT MODELS FL0111E FL0112E FL0122E. 367 mm."

Transcription

1 E N G L I S H FIRE ALARM ASPIRATION SENSING TECHNOLOGY QUICK INSTALLATION GUIDE STAND-ALONE FAAST LT MODELS FL0E FL0E FL0E mm mm 0 mm DESCRIPTION The LT FL0 Series is part of the Fire Alarm Aspiration Sensing Technology (FAAST) family. FAAST is an advanced fire detection system for use where early warning and very early warning are a requirement. The system continuously draws air from the controlled environment through a series of sampling holes to monitor the environment for smoke particulate. The FL0 is the stand-alone version of the FAAST LT range and is available in different models: FL0E - Has single channel capability with one laser smoke sensor. FL0E - Has single channel capability with two laser smoke sensors in a common chamber for coincidence detection. FL0E - Has two channel capability with two laser smoke sensors in separate chambers. (One sensor for each channel). This guide provides information for mounting and basic installation using the unit s default factory settings. For more extensive information please see the FAAST LT Advanced Setup and Control Guide - reference D SPECIFICATIONS Electrical Characteristics Voltage Range:. -. VDC Supply Current: Channel: 0mA (typical); 0mA VDC o C (excluding sounders) Channel: 0mA (typical); 0mA VDC o C (excluding sounders) Configurable Input: Activation Time: s (min) Relay Contact Ratings:.0 0 VDC, 0 VAC Environmental Ratings Temperature: -0 C to C Relative Humidity: 0% to % (non-condensing) IP Rating: Mechanical Exterior Dimensions: See Figure Wiring: 0. mm² to mm² max Maximum Single Pipe Length: 00m (Classes A. B & C) Maximum Number of Holes: See Table A Figure : Dimensions and Knock-Outs Pipe Spec (EN-0 Compliance): to EN (Crush, Impact, Temp ) Outside Pipe Diameter: mm (nom) or mm (nom) Shipping Weight:.kg (inc sensors) PARTS LIST mm Description Quantity FAAST LT unit Mounting bracket -pin Terminal block -pin Terminal block -pin Terminal block k-ohm EOL Resistor USB Cable Front Panel Labelling Pack Installation Kit CD Quick Installation Guide mm Important Note Aspirating Smoke Detectors supplied and installed within the EU must conform to the EU Construction Products Directive (/0/EEC) and the related European Product Standard EN -0. FAAST LT has been tested and certified to ensure that it conforms to the necessary Standards, but strict adherence to this instruction guide is advised to ensure that the installation meets the requirements of the CPD Directive D I--0 mm

2 ALARM PREALARM This equipment and all associated pipe work must be installed in accordance with all relevant codes and regulations. PHYSICAL INSTALLATION Front Panel Labels The LT FL0 is shipped without the front panel labels fixed in place. This allows the installer to choose the language required for the installation from the Front Panel Labelling Pack. Figure shows where the labels need to be placed: Figure : How to Knock Out Cable Gland Holes Mounting the LT FL0 to the Wall 0 0 INDICATES CENTRE OF ASPIRATING PIPES LEVEL LEVEL MODULE MODULE FAAST LT HANGING LUGS A FIXING HOLE USE FOR PLUMB-LINE FIXING HOLE LOW FLOW INPUT ASPIRATOR DISABLE EM / TEMPERATURE Figure : Mounting Bracket S YS T Figure : Placing the Front Panel Labels 0 mm mm When label A is in place, remove the protector from the bottom of the clear cover to stick the cover down, as shown in Figure : mm mm POSITION OF BRACKET * Figure : Remove Backing to Stick Cover Down PLUMB LINE mm Cable Access Knock out cable gland holes where required. The location of the cable gland holes is shown in Figure, represented by the icon: OUTER DIMENSION OF UNIT BASE OUTLINE * mm mm * Minimum clearance required from hinges to open door = mm. Figure : Fasten the mounting bracket to the wall D I--0 Pittway Tecnologica S.r.l. Via Caboto /, TRIESTE, Italy

3 Figure : Sequence ( to ) to Mount the Detector on the Bracket a mm mm Pipe Hole Configuration Figure below shows the pipe holes available on the unit. Each unit has pipe holes per channel (so if installing a channel unit, holes and do not function). Use Table to locate the holes required for the installation: Figure : Pipe Holes b 0 mm 0.00 o Table : Pipe Holes Used for Each FAAST LT Model c FAAST LT MODEL INLET PIPE HOLE OUTLET PIPE HOLE FL0E &, or or FL0E &, or or FL0E Channel &, or or Channel &, or or Note : Pipe holes not used should be kept sealed. Note : Do NOT glue pipes into the pipe holes. Table a: Maximum Number of Pipe Holes Allowed Per Channel mm All figures quoted using highest (level ) sensitivity CLASS PIPE LENGTH (m) MAX NUMBER OF HOLES PER CHANNEL C 00 (0 x.mm, x mm) + mm non sensing end hole) B 00 ( x mm, x mm inc end hole) A 00 x mm (+ mm non sensing end hole) A 0 ( x mm, x mm inc end hole) d Pipe Installation 0 D I--0

4 Exhaust Pipe SAMPLING AREA SAMPLING AREA WIRING INSTALLATION Power, Alarm and Control Connections CHANNEL CHANNEL EARTH BAR MOUNT EARTH BAR (OPTIONAL) AND ALARM CONNECTIONS EARTH BAR MOUNT USB PORT Note : All wiring should comply with local requirements and regulations. Note : Panel wiring must observe the recommendations of the panel manufacturer Figure : Inside the Detector COVER POSITION FOR TEST MAGNET POSITION FOR TEST MAGNET D I--0 Pittway Tecnologica S.r.l. Via Caboto /, TRIESTE, Italy

5 Table : Wiring Terminal Designations (Note - Terminals marked CH will only be available on channel models) No. Function Ext Power In + Primary PSU Ext Power In - Primary PSU Aux Power In + Not used in default T Aux Power In - Not used in default NC Alarm Relay CH C Alarm Relay CH T NO Alarm Relay CH NC Alarm Relay CH C Alarm Relay CH T 0 NO Alarm Relay CH NC Fault Relay CH C Fault Relay CH T NO Fault Relay CH NC Fault Relay (AUX) CH C Fault Relay (AUX) CH T NO Fault Relay (AUX) CH Sounder Output - Sounder Output + k-ohm EOL Resistor T Sounder Output - 0 Sounder Output + k-ohm EOL Resistor T Configurable Input + (Reset) Default is active = short circuit Configurable Input - (Reset) (unsupervised) T NC Pre-Alarm Relay CH C Pre-Alarm Relay CH T NO Pre-Alarm Relay CH NC Pre-Alarm Relay CH C Pre-Alarm Relay CH T0 NO Pre-Alarm Relay CH Table : Relays RELAY ACTION: NOTES ALARM or Set ON when ALARM CONDITION is met on a channel Default condition = Level. Alarm state is latched as default. A manual RESET is necessary to deactivate LED and relay. PRE-ALARM or Set ON when PRE-ALARM CONDITION Default condition = Level. is met on channel. or When CONDITION on Ch or Ch Fault state is not latched (default) or a common occurs. Fault is also indicated when in SERVICE mode and when the unit is unpowered. or Set ON when a channel is in ALARM / PRE-ALARM. Sounder corresponds to Ch and Sounder corresponds to Ch Default condition = set on in ALARM. ING UP Using Default Settings. Connect a suitable VDC supply (complying with European Standard EN -) to pins and on terminal block T (See Table ). Check the voltage at the connector. Make sure it is within the required voltage range.. If the voltage is within the specified range, connect the power connector to the unit.. Close and secure the housing door; verify the fan starts up and air flows out of the exhaust port. The unit takes - minutes to initialise and stabilise in normal mode. Configuring Other Options To change any of the default options, it will be necessary to connect the detector to a PC/laptop with the PipeIQLT software installed; see USB connection section later in this guide for more information on this (and the FAAST LT Advanced Setup and Control Guide). EXTERNAL RESET The default setting for the configurable external input is Device Reset (terminal block T). A short circuit connection between these terminals will cause the FAAST LT unit to perform a reset. D I--0

6 TEMPERATURE / INPUT FRONT PANEL The front panel will be different depending on which of the FL0 models is being installed, and each is shown below. The following information is displayed: Detector Status: Normal, Alarm, Fault or Isolate Alarm Level; Alarm, Pre-Alarm Particulate Levels; - Flow Level Test, Reset and Disable Buttons 0 ALARM PREALARM Figure 0: Front Panel Display LEVEL ALARM PREALARM 0 LOW FLOW ASPIRATOR DRIFT COMPENSATION TEMPERATURE / INPUT DISABLE / SYSTEM LEVEL 0b: FL0E Channel Detector ( Sensors) ALARM LOW FLOW ASPIRATOR DRIFT COMPENSATION DISABLE / SYSTEM 0 PREALARM 0 0a: FL0E Channel Detector ( Sensor) LEVEL LEVEL LOW FLOW ASPIRATOR DRIFT COMPENSATION TEMPERATURE / INPUT DISABLE / SYSTEM 0c: FL0E Channel Detector D I--0 Pittway Tecnologica S.r.l. Via Caboto /, TRIESTE, Italy

7 Table : Front Panel Indicators and Fault Descriptions INDICATOR ACTION WARNING OR TROUBLE COMMENT / ACTION CHANNEL / ALARM ON Red, Channel is in alarm (relay is No delay with default settings set) BLINK Green, when sensor is polled Not in alarm CHANNEL / PRE- ALARM ON Channel is in pre-alarm (relay is set) LEVEL ON Led number indicates sensor Only numbers used alarm level reached ON FAAST LT is in initialization ON Common or multiple faults BLINK Fault delay Default = 0s. ON FAAST LT is powered ON Low power alert / high power fault Check the power supply voltage. CHANNEL FLOW INDICATORS / ON The LED indicates the air flow for a channel: - Centre = normal flow - Left = flow low; (-0% at extreme) - Right = flow high; (+0% at extreme) On channel unit: Upper row = Ch Lower row = Ch LOW FLOW ON Low flow fault Check filter; check pipe network for blockages. BLINK Sensor initialization fault Try to restart device. Replace faulty sensor. BLINKS Sensor communication fault Check sensor addresses and installation; replace sensor. ASPIRATOR ON Air flow sensor fault Try to restart device. BLINK Flow initialization fault Check filter; check pipe network for blockages. Try to restart the device. BLINKS Fan fault Try to restart device. DRIFT COMPENSATION BLINK Drift compensation, st alert Clean sensor BLINKS Drift compensation, nd alert Clean sensor BLINKS Drift compensation limit warning Sensor needs urgent maintenance TEMPERATURE BLINK Low temperature alert Check the air flow temperature BLINKS High temperature alert Check the air flow temperature INPUT BLINK External input fault Not used with default settings DISABLE BLINK Alarms, faults & alerts not reported Returns to Maintenance then Normal operation after 0min (default) SYSTEM BLINK Wrong configuration Flashes all LEDs. Try to restart device. BLINKS EEPROM fault Check power supply voltage. Try to restart device BLINKS Real time clock fault RTC is corrupted or time reading failed. BLINK Sounder fault Check the sounder circuit and the EOL BLINK Filter alert at set date No date set as default ON High flow fault Check pipe network for breaks or leaks. In case of simultaneous alerts/faults on the same LED, priority order is: ON (Highest), blink, blinks, blinks (Lowest) Front Panel Buttons The front panel has user buttons: TEST, RESET and DISABLE. These buttons are used to enter the pass-code which then allows the user to carry out simple test functions. Note: In Remote Maintenance and Service Mode, these buttons are always disabled. Figure : User Interface Buttons D I--0

8 0 PREALARM 0 LEVEL LEVEL Table : Front Panel Buttons BUTTON NORMAL Mode MAINTENANCE Mode RESET When pressed for s, starts PASSWORD PROCEDURE to enter Maintenance mode. DISABLE TEST LEVEL Used to increment Password digits in PASSWORD PROCEDURE Used to confirm password in PASSWORD PROCEDURE. Default Password = When pressed for s latched alarms, faults and sounders (relays) are reset In DISABLE Mode, if pressed for s unit will exit from DISABLE Mode but remains in MAINTENANCE Mode When pressed for s, device enters DISABLE Mode for 0 minutes (default). (Alarms, alerts and faults not reported). (To exit DISABLE Mode see RESET) When pressed for s and released, both sensor will simulate alarm When pressed for s and released, sensor # will simulate alarm DRIFT COMPENSATION LOW FLOW TEMPERATURE / INPUT DISABLE / SYSTEM ASPIRATOR DRIFT COMPENSATION TEMPERATURE / INPUT COMBINATIONS RESET + DISABLE DISABLE / SYSTEM When pressed for s and released, sensor # will simulate alarm When pressed for s, shows fan speed (on smoke level scales) for a preset time. When pressed for s, shows fan speed (on smoke level scales) for preset time. RESET + TEST No action When pressed for s, turns off sounders RESET + TEST + DISABLE No action When pressed for s, unit exits from MAINTENANCE Mode Password Sequence to Enter Maintenance Mode Press and hold RESET; Left flow indicator will turn yellow, then green. Release RESET and indicator will switch on green. The left flow indicator will blink green indicating the device is ready for the first digit. Press DISABLE to increment the LEDs ; press TEST to select a digit. The flashing airflow segment will turn solid green and the next segment will begin to flash indicating set the next digit. When the th digit is selected, all airflow segments are turned off. If the password is accepted the indicator will remain green and the unit enters Maintenance mode. If the password is incorrect the indicator flashes yellow and the unit remains in Normal mode. The Default password in. If no button is pressed for 0s during the password sequence, the unit returns to Normal mode. If there is no activity in Maintenance mode for minutes (default), the indicator blinks green for s and then the unit returns to the Normal state. TESTING Magnet Test The alarm signalling can be tested for functionality by placing a test magnet in the position shown in Figure (displayed earlier in the guide). This method does not test the air flow in the pipe-work. Smoke Testing The system alarm response can be tested for functionality using smoke. The choice of smoke source is dependant on the installation but in all cases the smoke must be present for the duration of the test. Smoke pellets or matches can be used close to the sampling point to introduce smoke particulates into the system. It is recommended that smoke with a particulate life cycle of greater than 0s should be used standard aerosol sprays for point detector testing do not work well on aspirated systems. Fault Testing Simulate a fault on the detector (for example, block the outlet pipe) and check that a fault is signalled on both the front panel of the unit and at the CIE (Fire Panel). SERVICE WARNING Isolate the aspirating detector from the fire alarm system to prevent any unwanted alarms when opening the front door of the unit. Make sure all power is removed from the system before removing any covers. Service Mode Opening the cabinet door during normal operation will cause the unit to enter Service Mode. The LEDs will blink, the unit will switch off power to the fans and the fault relay will indicate a fault. When the cabinet door is closed, the unit restarts automatically. Filters Periodic cleaning or replacement of the filters will be required. The filters are located inside the cabinet at the top of the unit (see Figure displayed earlier in the guide) and are removed as shown in the sequence below: F i lters Either replace the filter assembly or carefully brush off the accumulated dust. Refit the filter, close and secure the cabinet door. The unit will initialise and re FOAM GASKET D I--0 Pittway Tecnologica S.r.l. Via Caboto /, TRIESTE, Italy

9 Either replace the filter assembly or carefully brush off the accumulated dust. Note: If replacing the filter, remove the foam gasket from the old filter and place onto the new filter. When placing the new filter into the slot, ensure that the gasket is correctly aligned. Refit the filter, close and secure the cabinet door. The unit will initialise and restart. Smoke Sensors The smoke sensors are located under the sensor cover (see Figure displayed earlier in the guide). To access the sensors, follow the sequence below: PipeIQ LT QUICK START INSTRUCTIONS Overview of PipeIQLT The PipeIQLT software program is a convenient and powerful Windows based application that can be used to quickly and accurately design pipe networks, generate configuration parameters for correct set-up and operation, and facilitate commissioning and monitoring of the performance of FAAST LT Aspiration devices. PipeIQLT provides a graphical interface on a PC to: Develop and verify the performance of pipe network solutions. Configure the design parameters to suit local fire codes and standards. Generate Pipe Layouts, BoMs, Configuration and Event Log Reports. Control, Test and Monitor FAAST LT devices. There is a comprehensive Help Menu to guide the user through the different windows and options. The contents have a detailed index and a versatile search facility to locate relevant topics. Minimum System Requirements Microsoft Windows XP SP or Windows GB of RAM. Graphics hardware with MB of memory and support for OpenGL.0 or later. GB of free hard disc space Installing PipeIQLT PipeIQLT is supplied on a mass storage device with each FAAST LT unit, or it can be accessed as a download from www. systemsensoreurope.com. To install from the mass storage device Insert and view the removable storage device. Click on PipeIQLT Setup: Do NOT interchange the devices and do NOT alter the rotary address switch settings on the sensors. If replacing a sensor, ensure that the address set on the new sensor is the same as on the sensor being replaced. LASER SAFETY INFORMATION The detector contains a Class laser product. Radiation emitted inside the smoke sensor is completely contained within its housings and protective covers during all phases of operation. USB CONNECTION PC connectivity is provided by an on board USB B socket located centrally between the filter and the sensor (see Figure displayed earlier in the guide). The USB interface allows access to a range of additional options, via the PipeIQLT application software, when connected to a PC. The USB connecting cable should be removed during normal operation. Click OK and follow the instructions (see: PipeIQLT Setup and Installation Wizard section below). To install from the website Click on the link to PipeIQLT at Click on PipeIQLT download. The download security warning will appear. Select Save, then click OK. When the download completes, click Run to display the above dialog box. Click OK and follow the instructions (see: PipeIQLT Setup and Installation Wizard section below). PipeIQLT Setup and Installation Wizard When the below dialog box appears, click Setup to start the wizard: D I--0

10 Quitting Exiting the program closes the application completely. To quit the PipeIQLT application, click X in the upper-right corner of the window. Or click Exit from the File menu. PipeIQLT can be uninstalled from the computer in the normal way for your operating system. Click Next and follow the on-screen instructions. Unless changed, the install wizard will create and store files at the following locations: When installation is complete, the wizard will automatically create a shortcut icon on the PC desktop. It will be necessary to re-boot the PC in order to run PipeIQLT. Launching To launch the PipeIQLT application, double click the PipeIQLT icon on the desktop. Or click Start (bottom left corner of the Windows screen) and then select PipeIQLT from the programs list. When the application opens, it is possible to start a new project, or to monitor or modify an existing project. Use the File menu to select New or Open. Choose from the Pipe Design, Configuration or Monitoring tabs to enter the required mode. Set the detector to Maintenance mode. To communicate with a FAAST LT detector, connect the USB port to a PC with an appropriate cable. 0 FL0E: 0-CPD-0 FL0E: 0-CPD- FL0E: 0-CPD- EN-0 : 00 Class A B & C Aspirating Smoke Detectors Pittway Tecnologica S.r.l. Via Caboto /, Trieste, Italy D I--0 Pittway Tecnologica S.r.l. Via Caboto /, TRIESTE, Italy

E N G L I S H FIRE ALARM ASPIRATION SENSING TECHNOLOGY QUICK INSTALLATION GUIDE ADDRESSABLE FAAST LT MODELS MI-FL2011EI, MI-FL2012EI AND MI-FL2022EI

E N G L I S H FIRE ALARM ASPIRATION SENSING TECHNOLOGY QUICK INSTALLATION GUIDE ADDRESSABLE FAAST LT MODELS MI-FL2011EI, MI-FL2012EI AND MI-FL2022EI E N G L I S H FIRE ASPIRATION SENSING TECHNOLOGY QUICK INSTALLATION GUIDE ADDRESSABLE FAAST LT MODELS MI-FL0EI, MI-FL0EI AND MI-FL0EI mm mm 0 mm DESCRIPTION The LT MI-FL0 Series is part of the Fire Alarm

More information

FL2011EI-HS FL2012EI-HS FL2022EI-HS

FL2011EI-HS FL2012EI-HS FL2022EI-HS Fire Aspiration Sensing Technology ENGLISH FL0EI-HS FL0EI-HS FL0EI-HS ADDRESSABLE FAAST LT-00 MODELS QUICK INSTALLATION GUIDE I - - 00 CONTENTS Introduction Parts List Specifications Physical Installation

More information

FAAST LT SET-UP AND TROUBLESHOOTING GUIDE. CONTENTS Introduction...1 Wiring up a FAAST LT unit...1. Setting the Fan speed...7

FAAST LT SET-UP AND TROUBLESHOOTING GUIDE. CONTENTS Introduction...1 Wiring up a FAAST LT unit...1. Setting the Fan speed...7 FAAST LT FIRE ALARM ASPIRATION SENSING TECHNOLOGY SET-UP AND TROUBLESHOOTING GUIDE CONTENTS Introduction....1 Wiring up a FAAST LT unit...1 Power connections and supervision 1 Sounder EOLs 1 Programmable

More information

RESET + Password Enter (During Auto Speed Procedure) Maintenance Timeout or after TEST + RESET + DISABLE (No Need for Device to Initialize)

RESET + Password Enter (During Auto Speed Procedure) Maintenance Timeout or after TEST + RESET + DISABLE (No Need for Device to Initialize) FAAST LT FIRE ALARM ASPIRATION SENSING TECHNOLOGY ADVANCED SET-UP AND CONTROL GUIDE CONTENTS Introduction....1 The FAAST LT Functional State Diagram....1 Password Procedure (to enter Maintenance Mode)

More information

Intelligent addressable fire alarm control panel

Intelligent addressable fire alarm control panel Intelligent addressable fire alarm control panel Input current consumption: Panel rating: Batteries: Networking and Interfaces Panel to panel communication: Number of panels: Interface port: System capacity

More information

Laptop / PC Programming Manual

Laptop / PC Programming Manual Laptop / PC Programming Manual Doc. # Fire PC Program rev B 01.07 This Document is property of Evax Systems, Inc. The Evax Fire Solutions Programmer Components 2 1.0 System Setup 4 1.1 Interface Setup

More information

LASER ASPIRATED SMOKE DETECTOR

LASER ASPIRATED SMOKE DETECTOR LASER ASPIRATED SMOKE DETECTOR LASD1 (Single Channel) INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS (CE) 1 INTRODUCTION The LASD1 utilises one or two high-sensitivity laser point detectors in an aspirated

More information

FAAST. Fire Alarm Aspirating Sensing Technology

FAAST. Fire Alarm Aspirating Sensing Technology FAAST Fire Alarm Aspirating Sensing Technology The FAAST range FAAST 8100e FAAST LT PipeIQ Next Generation Aspiration Detection Detection for Challenging Environments 3 in 1 Design, Confi guration and

More information

LASER ASPIRATED SMOKE DETECTOR

LASER ASPIRATED SMOKE DETECTOR LASER ASPIRATED SMOKE DETECTOR LASD2 (Dual Channel) INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS (CE) 1 INTRODUCTION The LASD2 utilises two, high-sensitivity laser point detectors in an aspirated

More information

FAAST XT 9400XA Fire Alarm Aspiration Sensing Technology

FAAST XT 9400XA Fire Alarm Aspiration Sensing Technology COMPREHENSIVE USER GUIDE FAAST XT 9400XA Fire Alarm Aspiration Sensing Technology SPECIFICATIONS Electrical Characteristics External Supply Voltage Remote Reset Time 18 30 VDC External monitor must be

More information

Alarm Client. Installation and User Guide. NEC NEC Corporation. May 2009 NDA-30364, Revision 9

Alarm Client. Installation and User Guide. NEC NEC Corporation. May 2009 NDA-30364, Revision 9 Alarm Client Installation and User Guide NEC NEC Corporation May 2009 NDA-30364, Revision 9 Liability Disclaimer NEC Corporation reserves the right to change the specifications, functions, or features,

More information

End To End Optical Beam Smoke Detector. Additional Information

End To End Optical Beam Smoke Detector. Additional Information End To End Optical Beam Smoke Detector Additional Information EN 1. Multiple Zone Wiring When using more than one System Controller on a single zone of a conventional Fire Control Panel (FCP), it is important

More information

FAAST 7100X INSTALLATION AND MAINTENANCE INSTRUCTIONS. Document Colour Code Key: (refer to Page 28) SPECIFICATIONS: TABLE OF CONTENTS

FAAST 7100X INSTALLATION AND MAINTENANCE INSTRUCTIONS. Document Colour Code Key: (refer to Page 28) SPECIFICATIONS: TABLE OF CONTENTS TABLE OF CONTENTS A. Specifications: 1 Introduction:.... 2 Description:... 2 Installation:...... 2 Wiring........... 3 User Interface:....... 5 Modes of Operation:..... 9 Logs..........11 External Monitor

More information

INSTALLATION AND MAINTENANCE INSTRUCTIONS 6500R AND 6500RS REFLECTIVE TYPE PROJECTED BEAM SMOKE DETECTOR

INSTALLATION AND MAINTENANCE INSTRUCTIONS 6500R AND 6500RS REFLECTIVE TYPE PROJECTED BEAM SMOKE DETECTOR INSTALLATION AND MAINTENANCE INSTRUCTIONS 6500R AND 6500RS REFLECTIVE TYPE PROJECTED BEAM SMOKE DETECTOR GENERAL The model 6500R is a conventional long range projected beam smoke detector designed to provide

More information

LM80031 Issue H. Installer s Handbook

LM80031 Issue H. Installer s Handbook LM80031 Issue H Installer s Handbook Index Introduction Page 3 0832 Kidde Products Limited Unit 2 Blair Way Dawdon City: Seaham, County Durham SR7 7PP UK 09 0832 CPD 1312 EN 54 20:2006 Aspirating smoke

More information

FAAST XS 7100X Fire Alarm Aspiration Sensing Technology

FAAST XS 7100X Fire Alarm Aspiration Sensing Technology COMPREHENSIVE USER GUIDE FAAST XS 7100X Fire Alarm Aspiration Sensing Technology SPECIFICATIONS Electrical Characteristics External Supply Voltage Remote Reset Time Power Reset Average Operating Current

More information

OVEN INDUSTRIES, INC.

OVEN INDUSTRIES, INC. OVEN INDUSTRIES, INC. OPERATING MANUAL Model 5C7-252 TEMPERATURE CONTROLLER With PLC Inputs Introduction Thank you for purchasing our controller. The Model 5C7-252 is an exceptionally versatile unit and

More information

HOBO U14 Data Logger User Manual

HOBO U14 Data Logger User Manual HOBO U14 Data Logger User Manual The U family of data loggers offers reliability and convenient monitoring for applications that require higher accuracy, better resolution, more memory, or USB connectivity

More information

FAAST. Fire Alarm Aspirating Sensing Technology

FAAST. Fire Alarm Aspirating Sensing Technology FAAST Fire Alarm Aspirating Sensing Technology The FAAST range FAAST 8100e FAAST LT PipeIQ Next Generation Aspiration Detection Detection for Challenging Environments 3 in 1 Design, Configuration and Monitoring

More information

FEC400 Series. Installation Manual

FEC400 Series. Installation Manual FEC400 Series Conventional microprocessor controlled fire detection and alarm panels with extinguishing control Installation Manual Version 2.3 / August 2004 Aritech is a GE Interlogix brand. http://www.geindustrial.com/ge-interlogix/emea

More information

User Manual. Dryer Controller M720

User Manual. Dryer Controller M720 User Manual Dryer Controller M720 Hardware version 1.00 Software version 1.00 Preliminary version Manual M720 Dryer controller Page 1 of 42 Document history Preliminary version: - Created in April, 2009

More information

FIRERAY 5000 range USER GUIDE

FIRERAY 5000 range USER GUIDE FIRERAY 5000 range USER GUIDE 0044-003-04 IMPORTANT PLEASE NOTE: The beam path MUST be kept clear of obstructions at all times! Failure to comply may result in the Detector initiating a Fire or Fault signal.

More information

IMPORTANT. PLEASE NOTE: The infrared beam path MUST be kept clear of obstructions at all times!

IMPORTANT. PLEASE NOTE: The infrared beam path MUST be kept clear of obstructions at all times! USER GUIDE English IMPORTANT PLEASE NOTE: The infrared beam path MUST be kept clear of obstructions at all times! Failure to comply may result in the Detector initiating a Fire or Fault signal. Contents

More information

Ontech GSM 9040/50. Reference Manual English -1 -

Ontech GSM 9040/50. Reference Manual English -1 - Ontech GSM 9040/50 Reference Manual English -1 - Content Welcome... 5 This manual... 5 Text styles... 5 Support... 5 Disclaimer... 5 Overview... 6 Accessories... 6 External temperature sensor 9901... 7

More information

D2E Duct Smoke Detector

D2E Duct Smoke Detector INSTALLATION AND MAINTENANCE INSTRUCTIONS D2E Duct Smoke Detector Specifications Operating Temperature: 20 to 60 C Storage Temperature: 20 to 60 C Humidity: 0% to 93% Relative Humidity Non-condensing Air

More information

INDEX 1- Introduction The Control Pane...7l 4.1- The Control Panel 1 and 2 Loops The Control Panel 4 and 8 Loops...

INDEX 1- Introduction The Control Pane...7l 4.1- The Control Panel 1 and 2 Loops The Control Panel 4 and 8 Loops... GUIDE MANUAL INDEX 1- Introduction...5...5...6 4- The Control Pane...7l 4.1- The Control Panel 1 and 2 Loops...7 4.2- The Control Panel 4 and 8 Loops...9 5- Installation Guide...10 5.1- Pre-Installation

More information

Dryer Controller M720

Dryer Controller M720 User Manual Dryer Controller M720 Hardware version 2.00 Software version 2.00 Manual M720 Dryer controller Page 1 of 60 Document history Preliminary version: - Created in April, 2009 Hardware Version 2.00,

More information

FAAST. Fire Alarm Aspiration Sensing Technology

FAAST. Fire Alarm Aspiration Sensing Technology FAAST Fire Alarm Aspiration Sensing Technology European Head Office Life Safety Distribution AG Javastrasse 2 8604 Hegnau Switzerland Tel: +41 44 943 4400 Email: sse.sales@systemsensor.com www.systemsensoreurope.com

More information

465 ma, All relays active, all alarm levels displayed

465 ma, All relays active, all alarm levels displayed INSTALLATION AND MAINTENANCE INSTRUCTIONS 8100 FAAST 3825 Ohio Avenue, St. Charles, Illinois 60174 Fire Alarm Aspiration Sensing Technology 1.800.SENSOR2; Fax: 630.377.6495 www.systemsensor.com SPECIFICATIONS

More information

CSP-204 CSP-208 CSP-104 CSP-108

CSP-204 CSP-208 CSP-104 CSP-108 Fire Alarm Control Panel CSP-204 CSP-208 CSP-104 CSP-108 Operation manual Firmware version 1.1 csp-x_o_en 06/15 SATEL sp. z o.o. ul. Budowlanych 66 80-298 Gdańsk POLAND tel. 58 320 94 00 www.satel.eu CONTENTS

More information

INSTALLATION AND MAINTENANCE INSTRUCTIONS 6500R AND 6500RS REFLECTIVE TYPE PROJECTED BEAM SMOKE DETECTOR

INSTALLATION AND MAINTENANCE INSTRUCTIONS 6500R AND 6500RS REFLECTIVE TYPE PROJECTED BEAM SMOKE DETECTOR INSTALLATION AND MAINTENANCE INSTRUCTIONS 00R AND 00RS REFLECTIVE TYPE PROJECTED BEAM SMOKE DETECTOR GENERAL The model 00R is a conventional long range projected beam smoke detector designed to provide

More information

Motorised Infrared Optical Beam Smoke Detector. User Guide

Motorised Infrared Optical Beam Smoke Detector. User Guide Motorised Infrared Optical Beam Smoke Detector User Guide EN 1. General Information 50cm 50cm 8-100m Ensure clear line of sight from Detector to Reflector Mount on solid surfaces (structural wall or girder)

More information

Instruction manual MTL process alarm equipment. October 2016 CSM 725B rev 2 MTL RTK 725B. Configuration Software Manual

Instruction manual MTL process alarm equipment. October 2016 CSM 725B rev 2 MTL RTK 725B. Configuration Software Manual Instruction manual MTL process alarm equipment October 2016 CSM 725B rev 2 MTL RTK 725B Configuration Software Manual SECTION 1 - INTRODUCTION... 5 Basic Requirements... 5 SECTION 2 - SOFTWARE INSTALLATION...

More information

PRODUCT INSTRUCTIONS. Fire Door Control Panel (FDCP) Stock Code Description Doc No: PI-115. Ellard Fire Door Control Panel Ellard Slave Repeater Unit

PRODUCT INSTRUCTIONS. Fire Door Control Panel (FDCP) Stock Code Description Doc No: PI-115. Ellard Fire Door Control Panel Ellard Slave Repeater Unit PRODUCT INSTRUCTIONS Fire Door Control Panel (FDCP) Floats Rd, Wythenshawe, Manchester. M23 9WB T: 44 (0)161 945 4561 F: 44 (0)161 945 4566 Stock Code Description Doc No: PI115 00133 00134 Ellard Fire

More information

Added password for IP setup page : Password must be in IP format!

Added password for IP setup page : Password must be in IP format! NETWORK POWER MONITOR Release : 21 August 2014 Hardware Version : Version 7 Firmware version 1.00 PC Application Software : Version (latest)...2 Added password for IP setup page : Password must be in IP

More information

EXTINGUISHING AGENT RELEASE MODULE

EXTINGUISHING AGENT RELEASE MODULE EXTINGUISHING AGENT RELEASE MODULE Operation, Installation & Programming Manual Revision 3.00 Distributors For: 18-20 Brookhollow Ave telephone 02 8850 2888 www.firesense.com.au Baulkham Hills NSW 2153

More information

THX-DL Data Logger USER & INSTALLATION MANUAL V

THX-DL Data Logger USER & INSTALLATION MANUAL V THX-DL Data Logger USER & INSTALLATION MANUAL V1.2012 www.thermomax-refrigeration.com Contents PRESENTATION Summary of Features 2 INSTALLATION Safety Precautions 4 THX Unit 4 Sensors 4 Alarm Relay 4 Power

More information

ViewMatrix. Software for Online Monitoring & Control of Matrix2000 Conventional Fire Alarm Panels. Version: 2.0 Revision: 0.1

ViewMatrix. Software for Online Monitoring & Control of Matrix2000 Conventional Fire Alarm Panels. Version: 2.0 Revision: 0.1 ViewMatrix Software for Online Monitoring & Control of Matrix2000 Conventional Fire Alarm Panels Version: 2.0 Revision: 0.1 CONTENTS 1. Introduction...3 2. Keyboard...5 2.1 POWER indication - Normal Operation...5

More information

USER MANUAL DexTempTM 1000 Temperature Monitor (P/N: IR-1001) DexTempTM 1000 USB Non-Contact Temperature Monitor. User Manual.

USER MANUAL DexTempTM 1000 Temperature Monitor (P/N: IR-1001) DexTempTM 1000 USB Non-Contact Temperature Monitor. User Manual. USER MANUAL DexTempTM 1000 Temperature Monitor (P/N: IR-1001) DexTempTM 1000 USB Non-Contact Temperature Monitor User Manual 8690 Rev B Update: 10/24/2013 1 Table of Contents 1 Introduction.. 3 2 Host

More information

SCAN200E USER S MANUAL

SCAN200E USER S MANUAL SCAN200E USER S MANUAL Code No. 2071 1052 rev. 1.4 Code No. 2071 1052 Rev. 1.4 Page 2/16 SCAN200E User s Manual Foreword This manual is for SCAN200E Controller running software version 2.03 or later. We

More information

PROPOINTPLUS ASPIRATING SMOKE DETECTION SYSTEM

PROPOINTPLUS ASPIRATING SMOKE DETECTION SYSTEM PROPOINTPLUS ASPIRATING SMOKE DETECTION SYSTEM INSTALLATION AND COMMISSIONING MANUAL Protec Fire Detection plc, Protec House, Churchill Way, Nelson, Lancashire, BB9 6RT, ENGLAND +44 (0) 1282 717171 www.protec.co.uk

More information

rvm4c Installation Guide Remote Video Module

rvm4c Installation Guide Remote Video Module rvm4c EN Installation Guide Remote Video Module rvm4c Installation Guide Installation Diagrams EN 2 Installation Diagrams for the Transmitting Unit rvm4c Installation Guide Basic Hardware Installation

More information

Halton SAFE / 7.14 user guide and installation instructions

Halton SAFE / 7.14 user guide and installation instructions Halton SAFE / 7.14 user guide and installation instructions VERIFIED SOLUTIONS BY H A LTO N Enabling Wellbeing Table of contents 1 System description 3 2 User Accounts 4 3 Main menu 7 3.1 Main menu - Change

More information

MODEL 6200 ANALOGUE ADDRESSABLE OPTICAL BEAM SMOKE DETECTOR

MODEL 6200 ANALOGUE ADDRESSABLE OPTICAL BEAM SMOKE DETECTOR MODEL 600 OPTICAL BEAM SMOKE DETECTOR ADDRESS CODING SW0 ON 4 8 4 8 UNITS TENS DIGIT REQUIRED Switch 8 Switch 4 Switch Switch 0 off off off off off off off on off off on off 3 off off on on 4 off on off

More information

System 800 Addressable Fire Detection & Alarm System

System 800 Addressable Fire Detection & Alarm System SECTION 5: page 1 Section 5: System 800 Addressable Fire Detection & Alarm System SECTION 5: page 3 10 reasons to specify 800 1 Plug and Play A user friendly panel not requiring special software tools

More information

4100U City and Relay Cards Installation Instructions

4100U City and Relay Cards Installation Instructions 4100U City and Relay Cards Installation Instructions Introduction This publication describes the installation procedure for the following: 4100-6031/6032 City Circuit Cards 4100-6033 Alarm Relay Card Inspecting

More information

Excel-EN Conventional Fire Control Panel

Excel-EN Conventional Fire Control Panel Available as 2, 4, 6, 8,10 or 12 zones Approved to EN54-2 & 4 Modular expansion zone cards Programmable relays and outputs Optional additional sounder circuits Optional additional programmable outputs

More information

RC-112 Two Speed Heat Pump 3 Stage Heat / 2 Stage Cool With Energy Efficient Control

RC-112 Two Speed Heat Pump 3 Stage Heat / 2 Stage Cool With Energy Efficient Control O M N I S T A T ELECTRONIC COMMUNICATING THERMOSTAT Installation Manual RC-112 Two Speed Heat Pump 3 Stage Heat / 2 Stage Cool With Energy Efficient Control Document Number 13I00-5 November, 1997 CONTENTS

More information

INSTALLATION AND MAINTENANCE INSTRUCTIONS 6500 AND 6500S REFLECTED TYPE PROJECTED BEAM SMOKE DETECTOR

INSTALLATION AND MAINTENANCE INSTRUCTIONS 6500 AND 6500S REFLECTED TYPE PROJECTED BEAM SMOKE DETECTOR INSTALLATION AND MAINTENANCE INSTRUCTIONS 6500 AND 6500S REFLECTED TYPE PROJECTED BEAM SMOKE DETECTOR GENERAL The model 6500 is an addressable long range projected beam smoke detector designed to provide

More information

This is to certify that the optical output of the: SENSORNET LR-DTS Temperature Sensing System: (Variants Mark 1, Mark 2a and Mark 2b)

This is to certify that the optical output of the: SENSORNET LR-DTS Temperature Sensing System: (Variants Mark 1, Mark 2a and Mark 2b) Optical Services Ltd. This is to certify that the optical output of the: SENSORNET LR-DTS Temperature Sensing System: (Variants Mark 1, Mark 2a and Mark 2b) Meets the requirements stated in IEC 60825-1:2001

More information

Motorised Infrared Optical Beam Smoke Detector. User Guide

Motorised Infrared Optical Beam Smoke Detector. User Guide Motorised Infrared Optical Beam Smoke Detector User Guide EN 1. General Information 50cm 50cm 8-100m Ensure clear line of sight from Detector to Reflector Mount on solid surfaces (structural wall or girder)

More information

Installation, Operating and Maintenance Manual

Installation, Operating and Maintenance Manual STATUS ZONES CONTROLS FIRE FAULT DISABLED FIRE 1 2 3 4 5 6 7 8 TEST FAULT DISABLED 1 5 BUZZER SILENCE RESET 1 2 TEST 2 6 LAMP TEST 3 SUPPLY 3 7 SYSTEM FAULT 4 8 SOUNDERS ACTIVATE/ SILENCE 4 FAULTS INSTRUCTIONS

More information

BSR Addressable Fire Detection control panel. Installation operation manual

BSR Addressable Fire Detection control panel. Installation operation manual BSR-1116 Addressable Fire Detection control panel Installation operation manual ATTENTION!!! READ THE MANUAL BEFORE THE INSTALLATION AND PAY ATTENTION TO PARAGRAPH 2.6.3 AND 2.6.4. Page 2 from 36 Contents

More information

SYSTEM MANUAL FT1-SB. Single Zone Fire Alarm System

SYSTEM MANUAL FT1-SB. Single Zone Fire Alarm System SYSTEM MANUAL FT1-SB Single Zone Fire Alarm System DOCUMENT HISTORY Issue Date Description Written By Checked By Draft 0 2/9/2008 Original Document. A. Shenouda C. Orr Issue 1 4/11/2011 Update drawing

More information

Consultant Specification AGILE Wireless Fire Detection System

Consultant Specification AGILE Wireless Fire Detection System Contents Scope of Work... 2 The EN54 Part 2 & 4 Fire System... 2 Standards... 2 Wireless Intelligent Photoelectric Smoke Detector Specification... 4 Wireless Intelligent Thermal Heat Detector Specification...

More information

VAP304 PRO INSTALLATION & OPERATION MANUAL

VAP304 PRO INSTALLATION & OPERATION MANUAL VAP304 PRO INSTALLATION & OPERATION MANUAL Panic Fire Duress Program Bypass Report Chime Test Memory B A D C Program Chime Panic Duress Exit Fire Report Bypass Memory Test Reset Password Exit Reset Password

More information

RANGER 8600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL

RANGER 8600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL RANGER 8600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS GENERAL DESCRIPTION... 2 STANDARD AND OPTIONAL PARTS LIST... 2 PARTS DIAGRAM... 3 TERMINAL DRAWING AND SPECIAL NOTES...

More information

MultiSite Manager. Setup Guide

MultiSite Manager. Setup Guide MultiSite Manager Setup Guide Contents 1. Introduction... 2 How MultiSite Manager works... 2 How MultiSite Manager is implemented... 2 2. MultiSite Manager requirements... 3 Operating System requirements...

More information

Siemens aspirating smoke detector (ASD) for the addressed FDnet/C-NET detector line or for standalone operation

Siemens aspirating smoke detector (ASD) for the addressed FDnet/C-NET detector line or for standalone operation Sinteso Cerberus PRO FDA241, FDA221 ASD Aspirating smoke detector Siemens aspirating smoke detector (ASD) for the addressed FDnet/C-NET detector line or for standalone operation Patented technology Early

More information

DUAL MONITORED INPUT/OUTPUT UNIT BN-305

DUAL MONITORED INPUT/OUTPUT UNIT BN-305 DUAL MONITORED INPUT/OUTPUT UNIT BN-30 Interactive fire detection systems Product Datasheet Features Interactive For interfacing and controlling external units to Autronica s interactive fire detection

More information

Operation Manual Fighter ProVision Software. Version: 0.0 Revision: 1

Operation Manual Fighter ProVision Software. Version: 0.0 Revision: 1 Operation Manual Fighter ProVision Software Version: 0.0 Revision: 1 TABLE OF CONTENTS 1. Introduction 5 2. Software Installation 5 3. PC Users 6 3.1 Introduction 6 3.2 Default Code 6 3.3 Edit PC User

More information

FTEN1, FTEN2, & FTEN4 1, 2 & 4 ZONE FIRE DETECTION AND ALARM CONTROL PANELS

FTEN1, FTEN2, & FTEN4 1, 2 & 4 ZONE FIRE DETECTION AND ALARM CONTROL PANELS QUICK USER GUIDE FOR, 2 & 4 ZONE PANELS INDICATORS COLOUR INDICATION MON FAULT Yellow On when a fault condition has occurred, or if no other fault Led is on, this indicates 24v auxiliary fuse failure.

More information

Centaur TM II Cube Slave Alarm Signalling Equipment INSTALLATION GUIDE

Centaur TM II Cube Slave Alarm Signalling Equipment INSTALLATION GUIDE Centaur TM II Cube Slave Alarm Signalling Equipment INSTALLATION GUIDE General Description This guide provides a summary for installing and configuring the Centaur TM Cube Slave Alarm Signalling Equipment

More information

Application, Installation, Operation & Maintenance Manual

Application, Installation, Operation & Maintenance Manual APPROVED BY:JBJ PRESCIENT III FIRE ALARM & GAS EXTINGUISHING CONTROL PANEL Application, Installation, Operation & Maintenance Manual PAGE 1 of 43 CONTENTS 1. INTRODUCTION... 3 2. GENERAL DESCRIPTION...

More information

Spa Touch Control Panel with BP2100, BP6013 spa controllers. (Spa Owner s Manual insert)

Spa Touch Control Panel with BP2100, BP6013 spa controllers. (Spa Owner s Manual insert) Spa Touch Control Panel with BP2100, BP6013 spa controllers. (Spa Owner s Manual insert) P.N. 7876C (export) February 12, 2015 For Spas equipped with BP2100, BP6013 controllers and Spa Touch panel. Spa

More information

Supervisor Standard Edition

Supervisor Standard Edition Supervisor Standard Edition Installation Manual Heat-Tracing Controller Configuration and Monitoring Software INSTALL-119 (Europe) 1 / 18 Contents Section 1 Introduction...3 1.1 Welcome...3 1.2 Vital Information...3

More information

BURGLAR ALARM PANEL BS-468

BURGLAR ALARM PANEL BS-468 BURGLAR ALARM PANEL BS-468 Contents 1. Description... 3 2. Instructions for the user... 4 2.1Basic operations... 4 Complete system.... 4 Split system.... 4 2.2 Armed system indication... 5 2.3 Advanced

More information

iminiplus PDF User Guide Version 2.0

iminiplus PDF User Guide Version 2.0 iminiplus PDF User Guide Version 2.0 Table of contents 1 Scope of this document... 3 2 Why PDF?... 3 3 Logger profile... 3 4 What you need to get started... 4 5 FDA 21 CFR Part 11 compliance... 5 6 How

More information

Replaceable LED modules. Sleep or unattended mode. Auto-silence and auto-acknowledge

Replaceable LED modules. Sleep or unattended mode. Auto-silence and auto-acknowledge Replaceable LED modules 11 Alarm Sequences as per ISA-18.1 standard Each channel/window fully field programmable RS232 or RS485 MODBUS-RTU communication Repeat relay for each window and multifunction relays

More information

Adaptive CyCLO Technical and HMI User Guide. CyCLO User Guide. Version th December 2017 REV

Adaptive CyCLO Technical and HMI User Guide. CyCLO User Guide. Version th December 2017 REV CyCLO User Guide Version 2.00 19 th December 2017 REV 2.00 1 Contents 1. Hardware... 3 1.1. Introduction... 3 1.2. Electrical Specification... 3 1.3. Board Overview... 4 1.4. Electrical Installation...

More information

POL-200-TS User Manual

POL-200-TS User Manual User Manual POL-200-TS ANALOGUE LOOP VERIFICATION TOOL 1/16 Security Information Several damage! Please, before to connect any external cable, ensure that loop cable has been disconnected from panel loop

More information

FI6000 INSTRUCTION MANUAL. Thank you for choosing another quality product from Amperes Electronics. Fire Alarm Interface

FI6000 INSTRUCTION MANUAL. Thank you for choosing another quality product from Amperes Electronics. Fire Alarm Interface INSTRUCTION MANUAL FI6000 Fire Alarm Interface Thank you for choosing another quality product from Amperes Electronics. FI6000 is a phase evacuation controller which can be integrated with various Amperes

More information

CommStat 4. Controller for Redundant Telecom HVAC Systems PRODUCT DATA SHEET. Features and Benefits

CommStat 4. Controller for Redundant Telecom HVAC Systems PRODUCT DATA SHEET. Features and Benefits CommStat 4 PRODUCT DATA SHEET Controller for Redundant Telecom HVAC Systems General Description The CommStat 4 is an HVAC controller designed specifically for controlling two redundant air conditioners,

More information

ocbridge Plus SPECIFICATION 3. COMPONENTS Wireless sensors receiver, battery СR2032, manual, instalation CD.

ocbridge Plus SPECIFICATION 3. COMPONENTS Wireless sensors receiver, battery СR2032, manual, instalation CD. 1 2 3 4 5 6 7 8 IN OFF ON + T S B J Т1 ocbridge Plus 1. FEATURES Wireless sensors receiver ocbridge is designated for connecting compatible Ajax devices to any third party wired central unit (panel) with

More information

Aspir A ation spir P R O D U C T S

Aspir A ation spir P R O D U C T S Aspiration PRODUCTS 2 The FAAST 8100 aspirating smoke detector combines dual source (blue LED and infrared laser) optical smoke detection with advanced algorithms to detect a wide range of fires while

More information

BS-316. Gas detection control panel up to 16 inputs. Installation operation manual

BS-316. Gas detection control panel up to 16 inputs. Installation operation manual BS-316 Gas detection control panel up to 16 inputs Installation operation manual Page 1 from 21 Contents 1 Operation instructions--------------------------------------------------------------------------------------------------------------------3

More information

Emerson Inspire 1HDEZ Installation Instructions. Thermostat/Interface Equipment Control TROUBLESHOOTING

Emerson Inspire 1HDEZ Installation Instructions. Thermostat/Interface Equipment Control TROUBLESHOOTING Emerson Inspire 1HDEZ-1521 Installation Instructions Thermostat/Interface Equipment Control TROUBLESHOOTING FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL

More information

SUPERINTEND VRE-08/16/32/64

SUPERINTEND VRE-08/16/32/64 SUPERINTEND VRE-08/16/32/64 Residual Current Monitoring System (RCM) for Grounded Electrical Systems 8/16/32/64 supervision points Operator Manual v2.00 Superintend VRE-08/16/32/64 operator manual v2.00

More information

PROPOINT PLUS ASPIRATING SMOKE DETECTION SYSTEM

PROPOINT PLUS ASPIRATING SMOKE DETECTION SYSTEM PROPOINT PLUS ASPIRATING SMOKE DETECTION SYSTEM USER MANUAL Protec Fire Detection plc, Protec House, Churchill Way, Nelson, Lancashire, BB9 6RT, ENGLAND +44 (0) 1282 717171 www.protec.co.uk sales@protec.co.uk

More information

Notifier by Honeywell: FAAST TM Fire Alarm Aspiration Sensing Technology

Notifier by Honeywell: FAAST TM Fire Alarm Aspiration Sensing Technology Notifier by Honeywell: FAAST TM Fire Alarm Aspiration Sensing Technology Notifier by Honeywell: FAAST FAAST Delivers When very early warning fire detection is essential FAAST is a ground breaking aspirating

More information

GSM RFID VOICE Alarm System

GSM RFID VOICE Alarm System GSM RFID VOICE Alarm System User s Manual For a better understanding of this product, please read this user manual thoroughly before using it. CONTENTS [Function Instruction] [Control Panel] Control Panel

More information

INSTALLATION AND MAINTENANCE INSTRUCTIONS TC866E Series LASER ASPIRATED SMOKE DETECTOR

INSTALLATION AND MAINTENANCE INSTRUCTIONS TC866E Series LASER ASPIRATED SMOKE DETECTOR INSTALLATION AND MAINTENANCE INSTRUCTIONS TC866E Series LASER ASPIRATED SMOKE DETECTOR INTRODUCTION There are many instances where aspirated smoke detectors are specified, but where the very high sensitivity

More information

D8024, D9024, D10024 Analog Fire Alarm Control Panels Programming Guide

D8024, D9024, D10024 Analog Fire Alarm Control Panels Programming Guide System Reset Trou ble Silence Ala rm Silence Manual Ala rm ENTER NO YES Letters Numb ers Keyword Radionics System Reset Trouble Silence Alarm Silence Manual Alarm ENTER NO YES Le ters Numbers Keyw ord

More information

TV2 Clean Room Monitor

TV2 Clean Room Monitor TV2 Clean Room Monitor 1. The Care and Use guide for your TV2 Clean Room Monitor can be downloaded here: www.e2di.com/usersguides.html Please print out the Users Guide. Although you should use the Users

More information

ZM2 OPERATING AND MAINTENANCE INSTRUCTIONS

ZM2 OPERATING AND MAINTENANCE INSTRUCTIONS ZM2 OPERATING AND MAINTENANCE INSTRUCTIONS CONTENTS 1. System Overview 2. User responsibilities 3. First Line controls and indications 3.1 Logging on to the fire alarm system 3.2 Checking system status

More information

The system is expanded via the RCC network with each RCC capable of passing information to and from up to 31 detection or output devices.

The system is expanded via the RCC network with each RCC capable of passing information to and from up to 31 detection or output devices. FireCell Radio Hub Fully addressable Wireless activation Third party approved (EN54) 2-way radio communication Loop powered Diagnostics port Range in excess of 150 metres Overview The model FCX-500-001

More information

PWM. Solar Charge controller with Ethernet. Solar Smart PWM 20Amp. Hardware Description : Release : 19 June 2014

PWM. Solar Charge controller with Ethernet. Solar Smart PWM 20Amp. Hardware Description : Release : 19 June 2014 Solar Charge controller with Ethernet Release : 19 June 2014 Hardware Version : Version 1 Firmware version 1 PC Application Software : Version 1.0.0.0 Hardware Description : The Solar Smart regulator was

More information

Solution F2. Fire Alarm Control Panels one step ahead.

Solution F2. Fire Alarm Control Panels one step ahead. Solution F2 Fire Alarm Control Panels one step ahead. Sicherheitstechnik Sicherheitstechnik GmbH GmbH The Fire Alarm Control Panel Solution F2 Solution F2 in B2 enclosure (B01090-00) The Concept The Solution

More information

IRIS Touch Quick Installation & Maintenance Guide. Version 1.0

IRIS Touch Quick Installation & Maintenance Guide. Version 1.0 IRIS Touch Quick Installation & Maintenance Guide Version 1.0 Page 2 of 16 IRIS Touch Quick Installation & Maintenance Guide Version 1.0 Contents 1. Introduction... 4 2. Product Features... 4 3. Package

More information

Written by: A.C. Amended by G.G. Checked by: JBJ/PB Approved by:jbj

Written by: A.C. Amended by G.G. Checked by: JBJ/PB Approved by:jbj Written by: A.C. Amended by G.G. Checked by: JBJ/PB Approved by:jbj Control Equipment Limited 32 Zone, 40 Character Discovery Panel, Voyager Panel and Integra Network Repeater Installation, Commissioning

More information

Patriot Systems Limited

Patriot Systems Limited COPYRIGHT 1997 - The Patriot Systems Ltd. Patriot Alarm Monitoring Automation Package is licensed for use on one computer, by the original person, or company, or organisation whose name is registered with

More information

Dashboard for Windows V1.1.0

Dashboard for Windows V1.1.0 User manual Dashboard for Windows V1.1.0 TBS Electronics BV De Factorij 46 1689 AL Zwaag The Netherlands www.tbs-electronics.com COPYRIGHT 2009 (rev1e) - 1 - TABLE OF CONTENTS 1. INTRODUCTION......................

More information

Danfoss gas detection units

Danfoss gas detection units Data sheet Danfoss gas detection units Types GD Premium, Premium+, Premium Duplex, Premium Remote, Premium Flex and Premium Uptime The Premium line gas detection units are used for monitoring and warning

More information

Simplex Panel Interface Guide

Simplex Panel Interface Guide Simplex Panel Interface Guide February 2016 SATEON Software Integrations Simplex Panel Interface Guide Issue 1.0, released February 2016 Disclaimer Copyright 2016, Grosvenor Technology. All rights reserved.

More information

MAKING MODERN LIVING POSSIBLE INT INT EFIT 550. User Guide and Installation Manual. Danfoss Heating

MAKING MODERN LIVING POSSIBLE INT INT EFIT 550. User Guide and Installation Manual. Danfoss Heating MAKING MODERN LIVING POSSIBLE EFIT 550 User Guide and Installation Manual Danfoss Heating Thank you for buying a Danfoss product. With this purchase you have obtained a product of the highest quality,

More information

Please use authentic SATA hard drive, USB device and battery.

Please use authentic SATA hard drive, USB device and battery. Note The device should be set in the room with good ventilation, far from water, hot reservoir or dust. Network Video Recorder is not designed to be used outdoor. Please use authentic SATA hard drive,

More information

Millennium Xtra. Millennium ATMA setup and configuration guide. May Millennium Group, Inc.

Millennium Xtra. Millennium ATMA setup and configuration guide. May Millennium Group, Inc. Millennium Xtra Millennium ATMA setup and configuration guide May 16 2017 Millennium Group, Inc. 16 Tech Circle Natick, MA 01760 P: 508-655-1340 F: 508-651-2902 Millennium ATMA setup and configuration

More information

ANALOGUE ADDRESSABLE FIRE PANEL MAGPRO96 INSTALLATION AND PROGRAMMING MANUAL

ANALOGUE ADDRESSABLE FIRE PANEL MAGPRO96 INSTALLATION AND PROGRAMMING MANUAL ANALOGUE ADDRESSABLE FIRE PANEL MAGPRO96 INSTALLATION AND PROGRAMMING MANUAL C 1293 Contents 1. INTRODUCTION...4 1.1 General Description... 4 1.2 General Specifications... 4 1.2.1 General Technical Specifications...

More information

Danfoss gas detection unit Type GD Heavy Duty

Danfoss gas detection unit Type GD Heavy Duty Data sheet Danfoss gas detection unit Type GD Heavy Duty The Heavy Duty gas detection units are used for monitoring and warning of hazardous Ammonia gas concentrations. They are intended for ATEX/ IECEx

More information

PowerRouter application guideline

PowerRouter application guideline PowerRouter application guideline Software installation tool - version 3.4 Before operating the PowerRouter, you may initialize the PowerRouter by using the PowerRouter software installation tool. The

More information