CIB 3076 Extra Alert Strobe (61221)

Size: px

Start display at page:

Download "CIB 3076 Extra Alert Strobe (61221)"

Clement Palmer
5 years ago
Views:

1 CIB 3076 Extra Alert Strobe (61221) CIB 3076 Comcode Issue 1

2 CIB 3076 Extra Alert Strobe (61221) The Extra Alert Strobe (Figure 1) emits a high intensity flashing light making you aware of voice terminal ringing in high ambient noise environments (e.g., heavy machinery areas), and quiet zones (e.g., hospitals, libraries, and broadcast studios). It is also ideal for alerting the hearing-impaired to voice terminal ringing. The strobe may be connected to your communications system s Extra- Alert/2-Line Power Failure Cartridge Type III for Models 206, 410 and 820, Services Module for Models 1030 and 3070, or Supplemental Alert Adapter (SAA). FIGURE 1 Extra Alert Strobe The Extra Alert Strobe comes with the following components: 25-Foot modular line cord Two mounting screws The following optional equipment is available from your local AT&T information Systems equipment supplier: Optional Equipment Order Number 25-Foot Modular Extension Cord Foot Modular Line Cord Line Bridging Adapter iss 1, cib3076-1

Testing the Extra Alert Strobe Before installing the Extra Alert Strobe, test for proper operation by temporarily connecting the strobe to your communications system.

3 Testing the Extra Alert Strobe Before installing the Extra Alert Strobe, test for proper operation by temporarily connecting the strobe to your communications system. 1 Plug one end of the modular line cord (provided) into the jack on the bottom of the strobe (Figure 2). Extra alert strobe Extra-Alert/2-Line Power Failure Cartridge Type III for Models 206, 410, and 820 Services Module for Models 1030 and Foot modular line cord (3) s Supplemental Alert Adapter (SAA) FIGURE 2 Testing the Extra Alert Strobe 2 Plug the other end of the modular cord into the jack pictured above (Figure 2) in your control unit or SAA. 3 Place a call into your communications system. The extra alert strobe is activated. NOTE: If you have any difficulties, make sure the modular line cord s connections are secure. If they are secure, replace the modular line cord and place another call into your communications system. Contact your equipment supplier if the strobe still does not operate. iss 1, cib3076-2

4 Installing the Extra Alert Strobe WARNING: National and local building codes and fire regulations forbid routing flammable wiring inside or on top of air plenums or ducts or along hot pipes. Consult your local ordinances and regulations for routing flammable wiring through walls or floors. The manufacturers, distributors, and their agents will not be responsible for damage due to improperly installed wiring. CHOOSING A LOCATION Choose a location for the strobe that is not more than 1,000 feet from your control unit or SAA. If you are using the cord supplied with the strobe, make sure the strobe is not more than 25 feet from your control unit or SAA. WALL-MOUNTING THE STROBE 1 2 Select a mounting location that is at least as large as the Extra Alert Strobe. Holding the template (provided at the end of these instructions) level, place it against the mounting location on the wall (Figure 3). iss 1, cib3076-3

Extra alert strobe (back view) Dry-wall fasteners (if required) Wall (side view) Keyholes Screws Mounting screw locations FIGURE 3 Wall Mount Installation 3 Using a pencil or sharp object, mark the

5 Extra alert strobe (back view) Dry-wall fasteners (if required) Wall (side view) Keyholes Screws Mounting screw locations FIGURE 3 Wall Mount Installation 3 Using a pencil or sharp object, mark the two mounting screw locations on the wall (Figure 3) Follow the instructions below for the type of mounting surface you have selected: For plywood walls or walls with a sturdy supporting structure (wood studs or crossmembers), insert and partially thread a screw (provided) into each of the previously marked mounting screw locations (Figure 3). For paneled, plaster, and plasterboard (hollow) walls, install 1/4 dry-wall fasteners (e.g., toggle or molly bolts)(not provided according to the manufacturer s instructions at each of the previously marked mounting screw locations (Figure 3). Partially thread the screws into the bolts. Tighten both screws. Then slightly loosen them so you will be able to place the strobe s keyholes over the screws. Place the back of the strobe against the screws (Figure 3), aligning the strobe s keyholes with the screws. Slide the switch down until it rests securely on the screws. iss 1, cib3076-4

6 CONNECTING THE EXTRA ALERT STROBE TO YOUR COMMUNICATIONS SYSTEM 1 Complete the wiring run from the strobe to your control unit or SAA (Figure 4), using one of the following: modular line and extension cords. modular line cords, jacks, and voice terminal cabling. Extra alert strobe 25-Foot modular extension cord A Modular jacks Extra-Alert/2-Line Power Failure Cartridge for Models 206, 410, and 820 Services Module for Models 1030 and 3070 (3) s 25-Foot modular line cord B C Modular line cord Supplemental Alert Adapter (SAA) Voice terminal cabling FIGURE 4 Connecting the Extra Alert Strobe to Your Communications System 2 3 Insert a Line Bridging Adapter (61401) (not provided) into a jack labeled A, B, or C in the illustration above (Figure 4) to connect an additional extra alert. Connect the modular plug from the wiring run into the jack pictured above (Figure 4) in your control unit or SAA. iss 1, cib3076-5

7 Template Use this template when wall-mounting your Extra Alert Strobe. Refer to the instructions (CIB 3076) for further information. iss 1, cib3076-6

CIB 3073 Extra Alert Bell (61212)

CIB 3073 Extra Alert Bell (61212) CIB 3073 Comcode 105-129-845 Issue 1 CIB 3073 Extra Alert Bell (61212) The Extra Alert Bell (Figure 1) provides audible alerts making you aware of voice terminal ringing