DIVISION 10 SPECIALTIES

Size: px

Start display at page:

Download "DIVISION 10 SPECIALTIES"

Harvey Maximilian Neal
5 years ago
Views:

1 DIVISION 10 SPECIALTIES 11/11

2 SECTION PLASTIC LAMINATE TOILET COMPARTMENTS PART 1 - GENERAL 1.01 SECTION INCLUDES Plastic laminate toilet compartments, urinal screens, head rail braced RELATED SECTIONS Section , Toilet and Bath Accessories 1.03 REFERENCES A. ANSI A Safety Standards for the Handicapped. B. ANSI A Mat Formed Wood Particleboard. C. APA - American Plywood Association. D. ASTM A167- Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip. E. NEMA LD-3- High Pressure Decorative Laminates SUBMITTALS A. Shop Drawings: Indicate partition plan, elevation views, dimensions, details of wall and floor supports, door swings. Submit plastic laminate colors for selection by Architect. B. Product Data: Provide data on panel construction, hardware, and accessories. C. Manufacturer s Installation Instructions: Indicate special procedures and perimeter conditions requiring special attention REGULATORY REQUIREMENTS Conform to ANSI A117.1 code for access for the handicapped FIELD MEASUREMENTS Verify that field measurements are as indicated on shop drawings /3

3 1.07 COORDINATION Coordinate the work with placement of support framing and anchors in wall. PART 2 PRODUCTS 2.01 ACCEPTABLE MANUFACTURERS A. Bobrick Washroom Equipment, Inc. B. AMPCO C. TEX-LAM 2.02 MATERIALS A. Wood Particle Board Core: ANSI A208.1, composed of 3 ply, 45 lb. density, resin impregnated particle board. B. Plastic Laminate: NEMA LD-3 General Purpose Type inch thick. C. Adhesive: Manufacturer's standard ACCESSORIES A. Pilaster Shoe: Formed chromed steel with polished finish, 3 inch high, with adjustable screw jack. B. Head Rails: Hollow aluminum tube, 1 x 1-5/8 inch size, with anti-grip strips and cast socket wall brackets. C. Attachments, Screws, and Bolts: Stainless steel; tamper proof type, heavy duty extruded aluminum brackets. D. Through Bolts and Nuts: Stainless steel with tamper proof heads. E. Steel Plate Reinforcement: Carbon steel, prepared for fasteners, 1/8 inch thick. F. Hardware: Chrome plated non-ferrous cast metal: 1. Pivot hinges, gravity type, adjustable for door close positioning. 2. Nylon bearings. 3. Thumb turn door latch with exterior emergency access feature /3

4 2.04 FABRICATION 4. Door strike and keeper with rubber bumper. 5. Coat hook with rubber bumper. 6. Door pull for outswinging doors. A. Fabricate partitions by applying single sheet plastic laminate finish to faces and edges of core material using adhesive and pressure bonding. B. Seal edges of cut-outs. Bevel corners and edges. C. Reinforce pilaster and panels with steel plate reinforcement sandwiched, within particle core at attachment points. Router cut openings as required. D. Doors and Panels: 1. Thickness: 1 inch 2. Door Width: Door Width for Handicapped Use: 36 inch, out-swinging. 4. Height: 58 inch panels, 84 inch to top of head rails. E. Thickness of Pilasters: 1-1/4 inch FINISHING Plastic Laminate, Two Colors: as selected by Architect from manufacturer s standard colors. PART 3 MEASUREMENT & PAYMENT (Not Used) END OF SECTION /3

5 SECTION TOILET AND BATH ACCESSORIES PART 1 - GENERAL 1.01 SECTION INCLUDES A. Toilet, and washroom accessories. B. Grab bars. C. Shower Room accessories. D. Washroom accessories to be installed in restrooms, break rooms, etc REFERENCES A. ANSI A Safety Standards for the Handicapped. B. ASTM A269 - Seamless and Welded Austenitic Stainless Steel Tubing for General Service. C. ASTM B456 - Electrodeposited Coatings of Copper Plus Nickel Plus Chromium and Nickel Plus Chromium SUBMITTALS Product Data: Provide data on accessories describing size, finish, details of function, attachment methods REGULATORY REQUIREMENTS Conform to ANSI A117.1 code for access for the handicapped FIELD MEASUREMENTS Verify that field measurements are as indicated on product data COORDINATION Coordinate the work with the placement of internal wall reinforcement to receive anchor attachments /4

6 PART 2 - PRODUCTS 2.01 MANUFACTURERS A. Georgia Pacific B. Bobrick. C. Other acceptable manufacturers offering equivalent products MATERIALS 1. Bradley. 2. McKinney. A. Tubing: ASTM A269, stainless steel. B. Fasteners, Screws, and Bolts: Stainless steel, tamper-proof, where exposed FABRICATION A. Weld and grind joints of fabricated components, smooth. B. Fabricate grab bars of tubing, free of visible joints, return to wall with end attachment flanges. Form bar with 1 1/2 inches (37 mm) clear of wall surface. Knurl grip surfaces. C. Shop assemble components and package complete with anchors and fittings. D. Provide steel anchor plates, adapters, and anchor components for installation FINISHES A. Shop Primed Ferrous Metals: Pre-treat and clean, spray apply one coat primer and bake. B. Enamel: Pre-treat to clean condition, apply one coat primer and minimum two coats epoxy baked enamel. C. Chrome/Nickel Plating: ASTM B456, satin finish. D. Back paint components where contact is made with building finishes to prevent electrolysis /4

7 PART 3 - EXECUTION 3.01 EXAMINATION A. Verify that site conditions are ready to receive work and dimensions are as instructed by the manufacturer. B. Verify exact location of accessories for installation PREPARATION A. Deliver inserts and rough-in frames to site for timely installation. B. Provide templates and rough-in measurements as required INSTALLATION A. Install accessories in accordance with manufacturers' instructions and ANSI A B. Install plumb and level, securely and rigidly anchored to substrate SCHEDULE A. Toilet 103: (No. of items per room, verify total count with drawings) 1. Soap Dispenser, Georgia Pacific #52052 (1 ea.) 2. Toilet Tissue Dispenser, Georgia Pacific #56733 (1 ea.) 3. Paper Towel Dispenser, Georgia Pacific #59460 (1 ea.) B. Toilet 107: (No. of items per room, verify total count with drawings) 1. Soap Dispenser, Georgia Pacific #52052 (1 ea.) 2. Grab Bar, Bobrick #B-6806x42, Satin Chrome (1 ea.) 3. Grab Bar, Bobrick #B-6806x36, Satin Chrome (1 ea.) 4. Toilet Tissue Dispenser, Georgia Pacific #56733 (1 ea.) 5. 24" x 36" Mirror w/ S. S. Frame, Bobrick #B (1 ea.) 6. Paper Towel Dispenser, Georgia Pacific #59460 (1 ea.) /4

8 7. Sanitary Napkin Disposal, Bobrick B-270, stainless (1 ea.) C. Showers 108: (No. of items per room, verify total count with drawings.) Heavy Duty Shower Curtain Rod (Clothes Rod), Bobrick #B-6047, Length as needed. (4 ea.) D. Men 109: (No. of items per room, verify total count with drawings) 1. Soap Dispenser, Georgia Pacific #52052 (2 ea.) 2. Grab Bar, Bobrick #B-6806x42, Satin Chrome (1 ea.) 3. Grab Bar, Bobrick #B-6806x36, Satin Chrome (1 ea.) 4. Toilet Tissue Dispenser, Georgia Pacific #56733 (2 ea.) 5. 24" x 36" Mirror w/ S. S. Frame, 6. Bobrick #B (2 ea. over wash station) 7. Paper Towel Dispenser, Georgia Pacific #59460 (2 ea.) PART 4 MEASUREMENT & PAINT (Not Used) END OF SECTION /4

9 SECTION FIRE EXTINGUISHER CABINETS AND ACCESSORIES PART 1 - GENERAL 1.01 SECTION INCLUDES A. Fire extinguishers cabinets B. Accessories. C. Fire Extinguishers will be provided by owner. Contractor shall coordinate with owner and mount fire extinguishers to meet applicable codes RELATED SECTIONS Section , Painting : Field paint finish REFERENCES A. ANSI/NFPA 10 - Portable Fire Extinguishers. B. ANSIIUL 711 -Rating and Fire Testing of Fire Extinguishers. C. UL Dry Chemical Fire Extinguishers SUBMITTALS A. Shop Drawings: Indicate cabinet physical dimensions, rough-in measurements for recessed cabinets, wall bracket mounted measurements, and location. B. Product Data: Provide cabinet operational features, color and finish and anchorage details. C. Manufacturer's Installation Instructions: Indicate special criteria and wall opening coordination requirements. D. Manufacturer's Certificate: Certify that Products meet or exceed specified requirements /3

10 1.05 REGULATORY REQUIREMENTS Conform to 2009 International Fire Code and NFPA for requirements for extinguisher cabinets and ADA for protruding objects. PART 2 - PRODUCTS 2.01 MANUFACTURERS A. J.L. Industries. B. Johnson-Lee, Div. of W.F. Lee Corp. C. Larsen's Manufacturing Co EXTINGUISHERS Extinguishers provided by Owner CABINETS A. Metal: Formed aluminum, Fire rated. B. Configuration: Semi-recessed type, exterior nominal dimensions of 9.5 inch wide x 24 inch high x 6 inch deep. C. Trim Type: Rolled edge with 2.5 inch wide face. Cabinet must comply with ADA maximum projection requirements. D. Door: 18 gage thick, reinforced for flatness and rigidity; latch with full glass access. E. Door Glazing: Wire glass, clear, 118 inch thick. F. Cabinet Mounting Hardware: Appropriate to cabinet ACCESSORIES Extinguisher Brackets: Formed steel, baked enamel finish FABRICATION A. Form cabinet enclosure with right angle inside corners and seams. Form perimeter rim and door stiles /3

11 B. Pre-drill for anchors. C. Hinge doors for 180 degree opening with continuous piano hinge. Provide roller type catch. D. Weld, fill, and grind components smooth FINISHES Cabinet and Door: Anodized to clear color. PART 3 - EXECUTION 3.01 EXAMINATION Verify rough openings for cabinet are correctly sized and located INSTALLATION A. Install in accordance with manufacturer's instructions. B. Install cabinets plumb and level in wall openings, height from finished floor to as indicated on plans. C. Secure rigidly in place. D. Coordinate with owner provided extinguishers and place extinguishers and accessories in cabinets or on wall brackets as indicated on plans. PART 4 MEASUREMENT & PAYMENT (Not Used) END OF SECTION /3

DESIGN AND CONSTRUCTION STANDARDS SPECIFICATION GUIDELINES

DESIGN AND CONSTRUCTION STANDARDS SPECIFICATION GUIDELINES SECTION 10 00 00 - SPECIALTIES 10 28 12 - TOILET PARTITIONS: Owner Preferences: Solid core phenolic, polymer based solid surfacing, and solid plastic toilet compartment and screen systems. No Stainless