Instruction Manual. AcuRite Atlas. Indoor Display model 06061

Transcription

1 Instruction Manual AcuRite Atlas Indoor Display model 06061

2 How It Works AcuRite Atlas is an environmental monitoring station that delivers key information on current outdoor conditions in your exact location. The outdoor device contains sensors that read temperature, humidity, wind speed and direction, rainfall, UV, light intensity, and optionally lightning (requires optional Lightning Detection Sensor; may be purchased separately). These readings are transmitted over a 433 MHz wireless radio frequency (RF) to be received by the AcuRite Atlas indoor touch screen display. Package Contents AcuRite Atlas TM Indoor HD Display AC Power Adapter for Display Wall Mounting Bracket (optional) NOTE: To view your outdoor readings online from My AcuRite an AcuRite Access is required; may be purchased separately. 2

3 Copyright Chaney Instrument Co. Set Up Your Indoor Display 1 Plug In Plug in the power adapter. Once the display is powered on, it will help guide you through the next steps. POWER ON 2 Lift Antenna On the top of the display, lift the antenna for optimal signal reception. 3 Install Batteries In the battery compartment of the AcuRite Atlas TM outdoor device, install four AA alkaline or lithium batteries. Lithium batteries are recommended in low temperature conditions, especially below -4 o F / -20 o C. Note: Heavy duty or rechargeable batteries are not recommended. 3

4 4 Mount Outdoor Device 5 For more details on outdoor device setup and placement, see the outdoor device instruction manual. Set Up Display Follow the on-screen prompts to set the time, date, and units of measurement. 1. Find a suitable place to mount the outdoor device: At least 5 feet (1.5 meters) off the ground Rear solar panel facing south Away from heat and humidity sources SOUTH OR Select Your Time Zone U.S. - Central Standard next Level for accurate rain reporting 2. Remove rain gauge stabilizer from outdoor device. REMOVE 4

5 How To Add An Outdoor Device To view your AcuRite outdoor device readings from an indoor display, the device must be added to the display. Note: This procedure is also required to be completed if you are replacing an outdoor device. 1. Verify the outdoor device is powered on. 2. From the top-left section of the indoor display, select the Menu icon ( ) 3. Select Sensors. Note: If you re replacing an outdoor device, select Remove A Sensor and remove the batteries and power from the outdoor device that is being replaced. 4. Select Add A New Sensor. The indoor display searches for any outdoor devices in wireless range. This may take a couple minutes. 5. Once the outdoor device has been located, select Add A Sensor. If more than one outdoor device has been detected, you may need to scroll up and down to select the appropriate device. 5

6 Features & Settings Outdoor temperature Wind last reading, wind direction arrow, two minute average, today s peak Ticker Menu Select to view monthly records, configure alarms, or set preferences 12 to 24 Hour Animated Weather Forecast Records Rainfall today s rainfall, rainfall rate, accumulated rainfall for current week, and month, and year to date SD card indicator Indicates an SD card is currently inserted in the display to log data 6 Display settings volume, brightness, sleep mode Indoor temperature & humidity Current date & time

7 Time And Date Settings You can set the indoor display s time and date settings, including the time zone, Daylight Saving Time, and the time and date format. How To Set Time and Date Formats 1. From the top-left section, select the Menu icon ( ). 2. Select Setup. 3. From the time and date setting section, set the settings. Follow the on-screen instructions. 4. Select Save. Note: The selected hour determines whether the time is a.m. or p.m. Unit Of Measurement Settings You can set the unit of measurement displayed for barometric pressure, temperature, wind direction, wind speed, rainfall, and lightning distance. How To Change Unit Of Measurement Settings 1. From the top-left section, select the Menu icon ( ). 2. Select Units. 3. Select the unit setting(s). 4. Select Save. Display Appearance Settings You can set the indoor display s brightness, contrast and tint levels, backlight dimming and sleep mode, and how often the display rotates between the main screen and records. How To Change Display Appearance Settings 1. From the top-left section, select the Menu icon ( ). 2. Select Display. 3. Adjust the display settings: Adjust Display set the display s brightness, contrast and tint levels. Display Mode set how often the display rotates between the main screen and the records screen. Backlight set the backlight, auto-dim, and sleep mode settings. 7

8 Charts & Monthly Records The indoor display stores in its local memory the last 48 hours of readings that are displayed in charts and the monthly reading records. Charts Available for Indoor and Outdoor Temperature and Humidity, Barometric Pressure, Light Intensity, UV, Wind Speed, Lightning, and Rainfall. Monthly Reading Records Shows high, low, and accumulation reading records by month. How To View A 6 Or 48-Hour Reading Chart 1. From the main screen, select a reading type. 2. From the top-section of the screen, select last 48 hours or last 6 hours. How To View Monthly Reading Records 1. From the top-left section, select the Menu icon ( ). 2. Select Records > Calendar. 3. To change the month displayed, use the left or right arrow to select a month. How To Delete Today s Records You can delete the current day s readings this feature is commonly accessed when inaccurate readings occur during the setup procedure or due to outdoor device mounting changes. 1. From the top-left section, select the Menu icon ( ). 2. Select Records. 3. Select Clear Today s Records. Today s records for all reading types are permanently deleted. Save Extended Historical Readings (Optional SD Card) The indoor display stores the last 48 hours of readings in its local memory. If you want to save detailed historical readings, you can automatically log the readings on an SD Card (not supplied). The indoor display can use an SD Card with up to 32 GB of space. Readings are saved to the SD Card every 10 seconds. Calibrations made to readings on the 8 readings sent to the SD Card.

9 ALARMS Alarms provide a quick and easy way to know when a condition you are monitoring has reached a certain threshold. When a condition set in an alarm is reached, the indoor display activates an an audible alarm and a display. About The Alarm Features Alarms can be set for temperature, humidity, rainfall, wind speed, time, and forecasted storms. Set the audible alarm volume or set the volume to off. Set a single alarm or all alarms to be disabled for those times you do not want to be disturbed. How To Set An Alarm 1. From the top-left section, select the Menu icon ( ). 2. Select Alarms. 3. Select Indoor on readings taken by the display. Select Outdoor readings taken by the outdoor device. 4. Using the left and right arrows, select an alarm type > select Next. 5. Set the condition that activates the alarm. When the condition is reached, 6. Verify the alarm icon is set to ON. 7. Select Save and Exit. low alarm ON How To Adjust The Alarm Volume 1. From the bottom-left of the display, locate the alarm volume icon. 2. To adjust the alarm volume, press the alarm volume icon to the desired level. To turn off the audible alarm, adjust the level until X is displayed. When set to alarm is active. How To Silence An Active Alarm 1. Push anywhere on screen to clear the trigger again the next time the parameter is reached. 2. Press the button twice to disable the alarm. The alarm press TWO TIMES to turn off alarm will not trigger again unless it is turned back on in Alarm Settings. 9

10 How To Disable A Single Alarm 1. From the top-left section, select the Menu icon ( ). 2. Select Alarms. 3. Select Indoor alarms on readings taken by the display. Select Outdoor alarms on readings taken by the outdoor device. 4. Using the left and right arrows, select the reading type of the alarm to be disabled > select Next. 5. Select the alarm icon until it displays OFF. OFF How To Disable All Alarms 1. Select Alarms. 2. Select Indoor alarms on readings taken by the display. Select Outdoor alarms on readings taken by the outdoor device. 3. Using the left and right arrows, select Turn All Alarms Off. 4. Select Next. All alarms are disabled. 5. Select Save and exit. 10

11 READING CALIBRATIONS When placement or an environmental factor may impact temperature, humidity, or barometric pressure readings, setting a calibration adjustment can improve accuracy. Note: Calibration adjustments are only applied to readings displayed on the indoor display and stored on the optional SD card. If your outdoor device readings are also sent to My AcuRite, the calibration adjustments set in the indoor display are not sent to My AcuRite or Weather Underground. How To Set A Reading Calibration 1. From the top-left section, select the Menu icon ( ). 2. Select Calibrate. 3. Select Indoor to adjust readings taken by the display. Select Outdoor to adjust readings taken by the outdoor device. 4. Using the up and down arrows, select the reading type to be calibrated > select next. 5. Using the up and down arrows, set an adjustment. 6. To save the calibration adjustment, select done. Indoor Display Sensors TEMPERATURE RANGE Indoor : 32ºF to 122ºF; 0ºC to 50ºC HUMIDITY RANGE Indoor : 1-100% RH BAROMETRIC PRESSURE 16 to inhg 11

12 HAVING PROBLEMS? We re Here to Help. Visit us online Get more information or download the full AcuRite Atlas product manual. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1- This device may NOT cause harmful interference, and 2- This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology. Visit for details. Limited One (1) Year Warranty A We warrant that the AcuRite Atlas Environmental Monitoring station premium product we manufacture and cover under this warranty is of good material and workmanship and, when properly installed and operated, will be free of defects for a period of one (1) year from the date of purchase. The AcuRite Atlas Environmental Monitoring station which, under normal use and service, is proven to breach the warranty contained herein within ONE (1) YEAR from date of sale will, upon examination by us, and at our sole option, be repaired or replaced by us. Transportation costs and charges for returned goods shall be paid for by the purchaser. We hereby disclaim all responsibility for such transportation costs and charges. This warranty does not cover normal wear and tear not affecting the functionality of the product, or products that have been damaged (including by acts of nature), tampered with, abused, improperly installed, or repaired or altered by anyone other than our authorized representatives. Remedy for breach of this warranty is limited to repair or replacement of the defective item(s). If we determine that repair or replacement is not feasible, we may, at our option, refund the amount of the original purchase price (excluding shipping). THE ABOVE-DESCRIBED WARRANTY IS THE SOLE WARRANTY FOR THE ACURITE ATLAS ENVIRONMENTAL MONITORING STATION PREMIUM PRODUCT AND IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. ALL WARRANTIES OTHER THAN THE EXPRESS WARRANTY SET FORTH HEREIN ARE HEREBY EXPRESSLY DISCLAIMED TO THE EXTENT PERMITTED BY LAW. We expressly disclaim all liability for special, consequential, or incidental damages, whether arising in tort or by contract from any breach of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. We further disclaim liability from personal injury relating to its products to the extent permitted by law. By acceptance of any of our products, the purchaser assumes all any other obligation or liability in connection with the sale of our pr is authorized to modify or waive the terms of this warranty unless done in writing and signed by a duly authorized agent of ours. In no case shall our liability for any claim relating to our products, your purchase or your use thereof, exceed the original purchase price paid for the product. WARRANTY CLAIMS T 1. Contact AcuRite Support at support@chaney-inst.com and provide opportunity for Customer Support to resolve any issue 2. In the event that an issue cannot be resolved over the phone, customer shall send the product(s) in for evaluation to AcuRite at the contact address (see below) 3. Chaney Instrument Service department will repair or replace product as necessary after evaluation The terms of this Limited Warranty shall be governed in all respects by and construed in accordance with the laws of the State out of this Limited Warranty or your use of the product shall be in the state court located in Walworth County, Wisconsin. You agree to submit to the jurisdiction of such court. Contact Information If you have questions about this Limited Warranty, please contact us at: AcuRite Attn: Warranty Inquiry 965 Wells St, Lake Geneva, WI warranty@chaney-inst.com Printed in China INST

13 Instruction Manual AcuRite Atlas Outdoor Device model 06059

14 How It Works Set Up Your AcuRite Atlas AcuRite Atlas is an environmental monitoring station that delivers key information on current outdoor conditions at its installation location. The outdoor device contains sensors that read temperature, humidity, wind speed and direction, rainfall, UV, light intensity, and optionally lightning (requires optional Lightning Detection Sensor; may be purchased separately). These readings are transmitted over a 433 MHz wireless radio frequency to be received by the AcuRite Atlas indoor HD display and/ or AcuRite Access. Readings received by AcuRite Access can be monitored and viewed online from My AcuRite. Receivers may not be included, and may be purchased separately. 1 Verify Package Contents 1. AcuRite Atlas outdoor device 2. Mounting bracket (for optional use) Mounting anchors & screws (for optional use) 4. Lightning Detection Sensor (optional; may be purchased separately) 4. 2

15 Device Components 1. Wind speed anemometer 2. Mounting knob 3. Battery compartment 4. Solar cell 5. Bubble level 6. UV and light sensor 7. Rainfall collector 8. Wind direction vane 2 Install Batteries Open the battery compartment, and insert four (4) AA alkaline or lithium batteries. Lithium batteries are recommended in low temperature conditions, especially below -4 F (-20 C). Note: Heavy duty or rechargeable batteries are not recommended

16 3 Optional: Install 4 Lightning Detection Sensor If you have the optional Lightning Detection Sensor, insert it in the battery Note: If you do not have a Lightning Detection Sensor, you can always add one later. Visit for more information. Mount Device Outdoors AcuRite sensors are sensitive to surrounding environmental conditions. Proper placement of the outdoor device is critical to the accuracy and performance of this product. Outdoor Device Placement AcuRite Atlas is designed to remain outdoors all year long. Mount the outdoor device in a location that meets all the requirements below: Located within 330 feet (100 m) of receiving device (AcuRite Atlas indoor display or AcuRite Access) Some construction materials and other sources of interference may reduce this distance. At least 5 feet (1.5 meters) off the ground Rear solar panel is facing south Away from heat and humidity sources Level for accurate rain reporting SOUTH OR 4

17 Placement for Maximum Accuracy Important Additional Placement Guidelines Choose an open location with no obstructions above or around the outdoor device for the most accurate measurements. Maximize Wireless Range Place outdoor device away from large metallic items, thick walls, metal surfaces, or other objects that may limit wireless communication. Maximize Temperature Accuracy Position outdoor device away from heaters, air conditioners, chimneys, exhaust vents, asphalt and concrete (surfaces that radiate heat). Maximize Humidity Accuracy Avoid installing the outdoor device near pools, spas, or other bodies of water. Maximize Wind Accuracy It s recommended to mount the outdoor device at least 5 feet (1.5 meters) off the ground, higher is better for wind measurement. The National Weather Service recommends 33 feet (10 meters) high. Avoid nearby wind obstructions such as trees and buildings. Be sure to mount the outdoor device securely, as swaying or shaking may cause inaccurate rain or wind readings. Note: Consider the optional Wind Extension kit (may be purchased separately) to extend the wind speed and direction sensors an additional 30 feet (9 meters) from the outdoor device to maximize the accuracy of wind measurements. Locate Away from Sprinkler Heads DO NOT install the outdoor device where it will be sprayed by a sprinkler system. This may force water inside the device. 5

18 6 Adjust the Wind Vane Orientation (Optional) Note: Most users will not need to complete this step. When mounting the AcuRite Atlas outdoor device, as long as the rear solar panel is facing south, the wind the factory. However, if you must mount the outdoor device in a different direction or otherwise need to adjust its wind vane orientation, complete the steps below. 1. In the battery compartment of the outdoor device, locate and press the calibration button. The red LED 2. Point the wind vane to north. You may need a north orientation. 3. While holding the vane facing north, press the calibration button in the battery compartment again. rapidly. Wind direction information will now use the new orientation. NORTH TEMPERATURE RANGE -40 to 158 F (-40 to 70 C) 30 seconds HUMIDITY RANGE 1-100% RH WIND SPEED mph (0-257 km/h) WIND DIRECTION 360 RAIN.01 inch intervals (mm) UV INDEX 0 to 15 index LIGHT INTENSITY to 120,000 Lumens *LIGHTNING Operating Range Up to 25 miles away (40 km) Reading Frequency 30 seconds 10 seconds 30 seconds 30 seconds 30 seconds 30 seconds 10 seconds Accuracy +_ 1 F +_ 2%RH +_ 1mph <_ 10 mph +_ 10% > 10 mph +_ 3 +_ 5% +_ 1 n/a n/a

19 HAVING PROBLEMS? We re Here to Help. Visit us online Get more information or download the full AcuRite Atlas product manual. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1- This device may NOT cause harmful interference, and 2- This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology. Visit for details. Limited One (1) Year Warranty A We warrant that the AcuRite Atlas Environmental Monitoring station premium product we manufacture and cover under this warranty is of good material and workmanship and, when properly installed and operated, will be free of defects for a period of one (1) year from the date of purchase. The AcuRite Atlas Environmental Monitoring station which, under normal use and service, is proven to breach the warranty contained herein within ONE (1) YEAR from date of sale will, upon examination by us, and at our sole option, be repaired or replaced by us. Transportation costs and charges for returned goods shall be paid for by the purchaser. We hereby disclaim all responsibility for such transportation costs and charges. This warranty does not cover normal wear and tear not affecting the functionality of the product, or products that have been damaged (including by acts of nature), tampered with, abused, improperly installed, or repaired or altered by anyone other than our authorized representatives. Remedy for breach of this warranty is limited to repair or replacement of the defective item(s). If we determine that repair or replacement is not feasible, we may, at our option, refund the amount of the original purchase price (excluding shipping). THE ABOVE-DESCRIBED WARRANTY IS THE SOLE WARRANTY FOR THE ACURITE ATLAS ENVIRONMENTAL MONITORING STATION PREMIUM PRODUCT AND IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. ALL WARRANTIES OTHER THAN THE EXPRESS WARRANTY SET FORTH HEREIN ARE HEREBY EXPRESSLY DISCLAIMED TO THE EXTENT PERMITTED BY LAW. We expressly disclaim all liability for special, consequential, or incidental damages, whether arising in tort or by contract from any breach of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. We further disclaim liability from personal injury relating to its products to the extent permitted by law. By acceptance of any of our products, the purchaser assumes all any other obligation or liability in connection with the sale of our pr is authorized to modify or waive the terms of this warranty unless done in writing and signed by a duly authorized agent of ours. In no case shall our liability for any claim relating to our products, your purchase or your use thereof, exceed the original purchase price paid for the product. WARRANTY CLAIMS T 1. Contact AcuRite Support at support@chaney-inst.com and provide opportunity for Customer Support to resolve any issue 2. In the event that an issue cannot be resolved over the phone, customer shall send the product(s) in for evaluation to AcuRite at the contact address (see below) 3. Chaney Instrument Service department will repair or replace product as necessary after evaluation The terms of this Limited Warranty shall be governed in all respects by and construed in accordance with the laws of the State out of this Limited Warranty or your use of the product shall be in the state court located in Walworth County, Wisconsin. You agree to submit to the jurisdiction of such court. Contact Information If you have questions about this Limited Warranty, please contact us at: AcuRite Attn: Warranty Inquiry 965 Wells St, Lake Geneva, WI warranty@chaney-inst.com 7

20 Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology. Visit for details. Printed in China INST

21 TM WHAT YOU NEED (not included) At least one compatible AcuRite device Network router with an available Ethernet port Always-on internet connection 1 2 PACKAGE CONTENTS 1. AcuRite Access 2. Ethernet cable 3. AC power adapter CONNECT ACCESS Connect the Ethernet cable to the Access AcuRite Access ID# XXXXXXXXX model# XXXXXX FCC XXXXXX AcuRite.com WRITE DOWN THE Device ID; printed on the bottom of the device. You will need this when adding the Access to myacurite.com. CONNECT 3Connect Ethernet cable to your network router.* INSTALL BACKUP BATTERIES 4On the bottom of the Access, remove 5 PLUG DEVICE ID IN Plug in the power adapter. The Access will take a minute to start up. the battery cover, then insert three AA alkaline batteries. ID# XXXXXXXXX model# XXXXXX FCC XXXXXX AcuRite.com POWER ON WAIT 6After starting the Access, the device will connect to My AcuRite and download available firmware updates. It may take up to 30 minutes. When Network Status Light stops flashing (is solid), you are READY for the next step. WAIT STEADY BLUE LIGHT 7 Create CREATE YOUR ACCOUNT your account and register your Access at NOTE: It may take up to 10 minutes for the Access to communicate with the My AcuRite service. OR AcuRite MyAcuRite APP

22 TM TROUBLESHOOTING Access is not recognized when adding to My AcuRite account Possible Solutions: Allow up to ten minutes for the Access Device ID to be activated with myacurite.com. Make sure you entered the Device ID correctly. Verify the 12-digit Device ID located on the bottom side of the Access and re-enter on My AcuRite. Verify the Access has a network (internet) connection. Access Has No Network (Internet) Connection Possible Solutions: Make sure the Ethernet cable is firmly connected. The cable may be defective and need to be replaced. The Ethernet port on your router may be malfunctioning. Try connecting the cable to another port. HAVING PROBLEMS? We re Here to Help! If you have reviewed the troubleshooting section and you still have questions, AcuRite offers several support options to help get the answers you want: Visit us online AcuRite.com offers customer support, videos, installation tips and a user forum. The AcuRite Support Forum is an active public community where you can exchange ideas and information with other PC Connect users, or post questions for customer support. AcuRite actively engages users in this forum to improve our products and services. Talk to a real person (877) Our friendly U.S. Based Support team is ready to assist you! You will find a knowledgeable, real person that is ready to help you on the other end of the line! After all, what good is all this technology without people standing behind it? More Information From your My AcuRite account, go to your Settings menu and select Help to view instructions, tips, and troubleshooting for the My AcuRite platform. Visit to learn more about your AcuRite products. Download additional documentation Tips and tricks to get the most out of your AcuRite products Videos and tutorials Purchase additional sensors Limited 1 Year Warranty AcuRite is a wholly owned subsidiary of Chaney Instrument Company. For purchases of AcuRite products, AcuRite provides the benefits and services set forth herein. For purchases of Chaney products, Chaney provides the benefits and services set forth herein. We warrant that all products we manufacture under this warranty are of good material and workmanship and, when properly installed and operated, will be free of defects for a period of one year from the date of purchase. Any product which, under normal use and service, is proven to breach the warranty contained herein within ONE YEAR from date of sale will, upon examination by us, and at our sole option, be repaired or replaced by us. Transportation costs and charges for returned goods shall be paid for by the purchaser. We hereby disclaim all responsibility for such transportation costs and charges. This warranty will not be breached, and we will give no credit for products which have received normal wear and tear not affecting the functionality of the product, been damaged (including by acts of nature), tampered, abused, improperly installed, or repaired or altered by others than our authorized representatives. Remedy for breach of this warranty is limited to repair or replacement of the defective item(s). If we determine that repair or replacement is not feasible, we may, at our option, refund the amount of the original purchase price. THE ABOVE-DESCRIBED WARRANTY IS THE SOLE WARRANTY FOR THE PRODUCTS AND IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. ALL OTHER WARRANTIES OTHER THAN THE EXPRESS WARRANTY SET FORTH HEREIN ARE HEREBY EXPRESSLY DISCLAIMED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. We expressly disclaim all liability for special, consequential, or incidental damages, whether arising in tort or by contract from any breach of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. We further disclaim liability from personal injury relating to its products to the extent permitted by law. By acceptance of any of our products, the purchaser assumes all liability for the consequences arising from their use or misuse. No person, firm or corporation is authorized to bind us to any other obligation or liability in connection with the sale of our products. Furthermore, no person, firm or corporation is authorized to modify or waive the terms of this warranty unless done in writing and signed by a duly authorized agent of ours. In no case shall our liability for any claim relating to our products, your purchase or your use thereof, exceed the original purchase price paid for the product. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1- This device may NOT cause harmful interference, and 2- This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI All other trademarks and copy-rights are the property of their respective owners. AcuRite uses patented technology. Visit for details. Printed in China INST

23