LED Multi-Level Options

Transcription

1 For use with Cree Edge, LEDway, LEDway SLM, SLM IP66, 227 Series, 228 Series, 34 Series, CPY Series, and VG Series Luminaires Product Description: The Cree Multi-Level options allow multiple operating drive currents for high and low dimming modes. The multi-level option includes a sensor integrated into the luminaire and is designed to operate all LEDs at the same drive current for maximum and uniform life. The occupancy sensor uses passive infrared technology that reacts to changes in infrared energy (moving heat) within the coverage area of the sensor. When motion is detected the luminaire is switched to high mode. After motion is no longer detected and the time delay cycle has been completed, the luminaire is returned to its low mode setting. The sensor itself includes eight possible ield adjustable settings for each of the following categories: Ambient, Time Delay, and. Ambient Light feature (A) is factory set at "OSO" which eliminates any daylight harvesting management and allows the ixture to operate only on occupancy. The Ambient Light feature includes eight possible ield settings: Occupancy Sensing Only (OSO): Occupancy detection (PIR) enabled only. Ambient Light sensing is disabled. The sensor will switch the luminaire to High mode during occupancy detection regardless of environment light levels. After motion is no longer detected and the time delay cycle has been completed, the luminaire returned to its low mode setting. Occupancy Sensing and Time Of (OSTO): Occupancy detection (PIR) enabled only with Time Of operation. Ambient light sensing is disabled. The sensor will switch the luminaire to High mode during occupancy detection regardless of environment light levels. After motion is no longer detected and the time delay cycle has been completed, the luminaire returned to its low mode setting. Sensor will switch the luminaire to Of after 3 minutes of no occupancy detection (Low mode). Occupancy Sensing and Low Ambient (OSLA): Occupancy detection (PIR) and Ambient Light sensing enabled. When environment light levels exceed 13 Lux (12 FC), luminaire will remain Of regardless of occupancy. If environment light levels are below 8 Lux (7 FC), luminaire will remain in Low mode during no occupancy and switch to High mode after occupancy is detected. Occupancy Sensing and High Ambient (OSHA): Occupancy detection (PIR) and Ambient Light sensing enabled. When environment light levels exceed 6 Lux (55 FC), luminaire will remain Of regardless of occupancy. If environment light levels are below 5 Lux (46 FC), luminaire will remain in Low mode during no occupancy and switch to High mode after occupancy is detected. Occupancy Sensing, Low Ambient and Time Of (OSLATO): Occupancy detection (PIR), Ambient Light sensing and Time Of enabled. When environment light levels exceed 13 Lux (12 FC), luminaire will remain Of regardless of occupancy. If environment light levels are below 8 Lux (7 FC) and occupancy is detected, luminaire will switch to High mode. After motion is no longer detected and the time delay cycle has been completed, the luminaire returned to its low mode setting. Sensor will switch the luminaire Of after 3 minutes of no occupancy detection (Low mode). Occupancy Sensing, High Ambient and Time Of (OSHATO): Occupancy detection (PIR), Ambient Light sensing and Time Of enabled. When environment light levels exceed 6 Lux (55 FC), luminaire will remain Of regardless of occupancy. If environment light levels are below 5 Lux (46 FC) and occupancy is detected, luminaire will switch to High mode. After motion is no longer detected and the time delay cycle has been completed, the luminaire returned to its low mode setting. Sensor will switch the luminaire Of after 3 minutes of no occupancy detection (Low mode). The following features are used to bypass sensor: Lock Low Mode (LL): Sensor locks in level indeintely. The occupancy detection (PIR) and Ambient Light operation are disabled during the Lock Low mode. Typically used for test mode. Lock High Mode (LH): Sensor turns the ixture on at the low level set by setting. Sensor will cycle every 5 seconds between speciied Low and High dimming settings for 4 complete cycles (Low, High, Low, High) and then locks in High indeintely. The occupancy detection (PIR) and Ambient Light operation are disabled during the Lock High mode. Typically used for test mode. Time Delay feature (D) can be adjusted from.5 min to 3 min. and is factory set at 4 min. Once motion is detected, the lighting load will remain in the High Mode until motion is no longer detected and the time delay cycle has been completed. feature (L) can be adjusted from an of position to a maximum drive current of 325mA and is factory set at 75mA. feature (H) can be adjusted from a ma drive current to a maximum drive current of ma and is factory set at ma. Please note some luminaires may be rated for ma maximum drive current.. Rev. Date: 8/3/212

2 Figure 1 LEDway Streetlights, LEDway SLM Streetlights, SLM IP66 Street and Area Luminaires, and Cree Edge Flood and Area Luminaires, Cree Edge High Output Flood and Area Luminaires Coverage Top View Temperature 25º C Coverage Side View ' 1' 1' 3' 12.2m 9.1m m 3.m 3.m m 9.1m 12.2m 12.2 Figure 2 Cree Edge Canopy, Cree Edge Round Area, 34 Series Canopy, 227 Series Upgrade, 228 Series Canopy, and CPY25 Canopy / Soffit Luminaires Temperature 25º C (77º F) Coverage Top View 3 m 3 Coverage Side View 1' 3 m 1' 3 15' 1' 5' 5' 1' 15' m 4.6m 3m 1.5m 1.5m 3m 4.6m m 1' 1' Figure 3 Cree Edge Security, Cree Edge Parking Structure, 34 Series Parking Structure, and VG Series Vehicle Garage Luminaires Temperature 25º C (77º F) Coverage Top View m 25' Coverage Side View 1' 12.5' m 15' 1' 5' 25' 5' 1' 15' 25' 3m 1.5m 1.5m 3m 4.6m 4.6m m m m m 12.5' 25' 25' 12.5' 12.5' 25' Luminaire LEDway Streetlights, LEDway SLM Streetlights, SLM IP66 Street and Area Luminiares, Cree Edge Flood and Area Luminaires, Cree Edge High Output Flood and Area Luminaires Cree Edge Canopy, Cree Edge Round Area, 34 Series Canopy, 227 Series Upgrade, 228 Series Canopy, and CPY25 Canopy / Soffit Luminaires Cree Edge Security, Cree Edge Parking Structure, 34 Series Parking Structure, and VG Series Vehicle Garage Luminaires Sensor Details Lens Lens coverage: 3' (9.1m) optimal mounting height and 6' (18.3m) diameter coverage with a 36 circular pattern. The minimum and maximum mounting heights are (m) (12.2m) respectively. Lens mounting height to coverage radius is 1:1. See Figure 1. Note: When mounting heights are above 3' (9.1m), the sensor only detects large objects such as fork lift trucks or cars. Lens coverage: (m) optimal mounting height and (12.2m) diameter coverage area with a 36 circular pattern. The minimum and maximum mounting heights are 1' (3m) and 3' (9.1m) respectively. Lens mounting height to coverage radius ratio is 1:1. See Figure 2. Lens coverage: 1' (3m) optimal mounting height and 5' (15.2m) diameter coverage area with a 36 circular pattern. The maximum mounting height is 15' (4.6m). Lens mounting height to coverage radius is 1:2.5. See Figure 3.

3 Product Availability Cree Edge Luminaire Availability Direct & Adjustable Arm s Area Area Round 1 Canopy Post Top s SA s Direct & Adjustable Arm s Interior Round 1 Parking 1 Pathway 1 Security All s All s All s All s Wall LEDs F,P,R 4-16 LEDs F,P N/A 4-12 LEDs F 4-16 LEDs F,P N/A 4-1 LEDs F N/A 2-8 LEDs F LEDs 4-8 LEDs N/A N/A N/A N/A N/A N/A N/A LEDs F,P,R 4-16 LEDs F,P N/A 4-12 LEDs F 4-16 LEDs F,P N/A 4-1 LEDs F N/A 2-8 LEDs F LEDs 4-8 LEDs N/A N/A N/A N/A N/A N/A N/A LEDs F,P,R 4-6 LEDs F,P N/A 4-6 LEDs F 4-6 LEDs F,P N/A 4-6 LEDs F N/A 2-8 LEDs F LEDs 4-6 LEDs N/A N/A N/A N/A N/A N/A N/A 1 Consult Area Round / Pathway / Interior Round Multi-Level spec sheet for availability. F Multi-Level option available with Fusing option. P Multi-Level option available with Photocell option. R Multi-Level option available with NEMA Photocell Receptacle option. 1 Horizontal Tenon F Multi-Level option available with Fusing option. R Multi-Level option available with Receptacle option. LEDway Luminaire Availability LEDway Streetlight LEDWay SLM Streetlight SLM IP66 Streetlight IP66 Rated s Horizontal Tenon All s N/A 2-12 LEDs F,R N/A N/A N/A 2-12 LEDs F,R N/A 2-6 LEDs F,R N/A 2-12 LEDs F,R N/A 2-6 LEDs F,R N/A N/A N/A 2-4 LEDs F,R for Single Skin Canopies Canopy for Double Skin Canopies F Multi-Level option available with Fusing option. Upgrade Kit s 34 Series Luminaire Availability Parking Structure All s Floodlight Interior Soffit Yoke s IC Rated LEDs F 4-6 LEDs F 4-6 LEDs F 4-6 LEDs F 4-6 LEDs F 4-6 LEDs F N/A 4-6 LEDs F N/A N/A N/A N/A N/A N/A LEDs F 4-6 LEDs F 4-6 LEDs F 4-6 LEDs F 4-6 LEDs F 4-6 LEDs F N/A 4-6 LEDs F N/A N/A N/A N/A N/A N/A LEDs F 4-6 LEDs F N/A 4-6 LEDs F 4-6 LEDsF N/A N/A N/A N/A N/A N/A N/A N/A N/A IC Rated 228 Series Luminaire Availability Canopy Soffit Upgrade Kit s IC Rated LEDs N/A 3, 6 LEDs N/A , 6, 9 LEDs 3, 6 LEDs 3, 6 LEDs N/A , 6, 9 1 LEDs 3, 6 LEDs N/A N/A LEDs 1 N/A N/A N/A LEDs 1 N/A N/A N/A 1 Requires marked spacing 48" (1,219mm) x 24" (61mm) x 6" (152mm); 48" (1,219mm) luminaire to luminaire, 24" (61mm) luminaire to side wall, 6" " (152mm) above luminaire.

4 Product Availability Continued VG Series Luminaires CPY25 Luminaires Input Power Designator Availability Input Power Designator Availability A Available 347, 48 Available A B N/A N/A Available N/A ma Note: For use with products when ma drive current is speciied. Speciied drive current represents the maximum drive current range of dimming. s are for estimating purposes only. Check actual spec sheet data where available. s V V Position OFF OFF Position s V V Factory Dimming s 4 (HL) 75mA ma 5 (HK) 175mA ma ma Note: For use with products when ma drive current is speciied. Speciied drive current represents the maximum drive current range of dimming. s are for estimating purposes only. Check actual spec sheet data where available. s V V Position OFF.. OFF Factory Dimming s (CL) 75mA ma 1 (CK) 175mA ma

5 ma Continued Note: For use with products when ma drive current is speciied. Speciied drive current represents the maximum drive current range of dimming. s are for estimating purposes only. Check actual spec sheet data where available. Position s V V ma Note: For use with products when ma drive current is speciied. Speciied drive current represents the maximum drive current range of dimming. s are for estimating purposes only. Check actual spec sheet data where available. s Position V V. OFF... OFF Position s V V Factory Dimming s 2 (DL) 75mA ma 3 (DK) 175mA 7mA

6 15mA Note: For use with products when 15mA drive current is speciied. Speciied drive current represents the maximum drive current range of dimming. s are for estimating purposes only. Check actual spec sheet data where available. Position s s V V. OFF Factory Dimming s 6 (XL) 11mA 1mA 7 (XK) 27mA 1mA VG Series Note: For use with products VG Series luminaires Position s s V V Factory Dimming s ) CPY Series Note: For use with products CPY25 luminaires Position s s V V of Factory Dimming s ) Cree, Inc. and/or one of its subsidiaries. All rights reserved. For informational purposes only. Content is subject to change. See for patent and warranty information. Cree, LEDway, and the Cree logo are registered trademarks, and the BetaLED Technology logo, Cree Edge, LEDway SLM, SLM IP66, 227 Series, and 228 Series are trademarks of Cree, Inc. or one of its subsidiaries.