Erbium-Doped Fiber Amplifier (EDFA) - MW Series

Size: px
Start display at page:

Download "Erbium-Doped Fiber Amplifier (EDFA) - MW Series"

Transcription

1 Nanovation s MW series of EDFA products is designed for applications in advanced dense wave division multiplexing (DWDM) systems where high performance and reliability are critical. They are available in Booster, Inline and Preamplifier configurations to cover a wide range of applications in the full C-Band. A sophisticated micro-controller monitors and controls the internal components, while the incorporated RS-232 interface permits the user to remotely control the device or monitor the internal fault alarms. These devices can be programmed to operate in either the constant gain or constant power mode. The integrated control system assures that adding or dropping wavelengths in state-of-the-art DWDM systems is accomplished with minimum system disturbance. Features Excellent gain flatness over the full C-Band High saturated output power Low noise figure Internal microcontroller for monitoring, alarm and control functions AGC, APC or ACC operation mode with AGC as default Input and output optical isolation and power monitoring TTL compatible alarm and warning capability Low power consumption, single 5V power supply operation RS-232 serial interface for system integration and diagnostics Wide operating temperature and humidity ranges Compact packaging Bellcore GR-1312-CORE qualified and ISO 9001 certified Applications High performance Full C-Band DWDM systems Booster, inline or preamplifier configurations Product Description General The MW series of EDFA products has been specially designed for use in DWDM transmission systems as a booster, inline, or preamplifier. A sophisticated internal electronic control system maintains the performance of the module, provides monitoring information, enables the module to be set to specific operational states, and incorporates a series of alarm signals associated with a range of potential system faults. Each module can operate under independent control in combinations of constant output power or constant gain control with fast transient suppression. This function is provided by the microcontroller that monitors the input power and drives the pump lasers under closed-loop feedback control. These features permit wavelengths to be rapidly added or dropped from the amplifier while controlling the impact on the remaining channels. Optical The amplifiers have been optimized for the full C-Band (1530 to 1562 nm) gain-bandwidth DWDM operations by careful selection of both passive and active components. All amplifiers are pumped with high reliability pumps, and are provided with optical monitor outputs to allow customer spectral analysis or monitoring of the amplified signal. An optical output monitor port is a customer option that can assist the user in such analysis or monitoring. Operation mode AGC (Automatic Gain Control) - default APC (Automatic Power Control) - optional ACC (Automatic Current Control) for performance monitoring Electrical Electrical connection is through a standard male DB25 connector. Control System Internal electronic circuits provide the pump lasers with electrical transient protected power supply and temperature control. A microcontroller monitors and controls the module and provides an external RS232 serial interface, through which operation mode and other configurations can be customized. A series of digital outputs provides a set of alarms that indicate a range of module and system faults. Package The units are housed within very small modules with input and output connections through single mode fiber pigtails and are fitted as standard with super-polished FC/UPC or FC/APC connectors. Other types of connectors are available on request. V011 1-

2 Absolute Maximum Ratings (in accordance with Bellcore GR-1312-CORE) Erbium-Doped Fiber Amplifier (EDFA) - MW Series Parameter Min. Typical Max. Unit DC Operating Voltage V Current Consumption A Operating Temperature Range 0-70 C Storage Temperature Range C Operating Humidity Range 5-85 % Pigtail Fiber Fiber Type Standard single-mode fiber Fiber/Buffer Diameter (mm) 0.9 Pigtail Length (m) 1.0 (or user defined) MW EDFA Typical Performance Curves Boost Configuration 1-20 V011

3 MW Series EDFA Electrical Interface The MW series of EDFA products is equipped with a standard DB25 male connector. The functionality of each pin is presented below: Pin Symbol Description 1 Vcc Power Supply: +5volts DC, +/- 5%, Imax =3.0 A 2 Vcc Power Supply: +5volts DC, +/- 5%, Imax =3.0 A 3 Vcc Power Supply: +5volts DC, +/- 5%, Imax =3.0 A 4 Vcc Power Supply: +5volts DC, +/- 5%, Imax =3.0 A 5 Pout Output Power Monitor 6 Pin Input Power Monitor 7 AL1 Alarm Mode 1- Internal temperature exceeds preset value 8 AL2 Alarm Mode 2- Optical output power decreases 2dB below preset value 9 AL3 Alarm Mode 3- Pump laser current decreases 1 ma below preset value 10 AL4 Alarm Mode 4- Pump laser temperature exceeds preset value 11 AL5 Alarm Mode 5- Reflected output power exceeds preset value 12 Vcc Power Supply: +5volts DC, +/- 5%, Imax=3.0 A 13 GND Power supply ground / case 14 GND Power supply ground / case 15 GND Power supply ground / case 16 GND Power supply ground / case 17 GND Power supply ground / case 18 TXD RS-232 DATA OUT (TTL Levels) 19 AL6 Alarm Mode 6 Optical input power decreases below preset value 20 N/C 21 Adis Pump laser ON/OFF toggle 22 RXD RS-232 DATA IN (TTL Levels) 23 N/C 24 Vcc Power Supply: +5volts DC, +/- 5%, Imax =3.0 A 25 GND Power supply ground TTL Input/Output Monitor and Control Logic Levels The TTL input and output monitor (AL1 AL6) and control logic (A dis ) levels are presented in the following table. The correspondence between the analog optical signal level and the analog voltage output is typical. The actual analog sensitivity coefficients are supplied with each EDFA. Function In/Out TTL High TTL Low Internal Temperature Monitor (pin 7) Out Normal Alarm Output Power Monitor (pin 8) Out Normal Alarm Pump Laser Current Monitor (pin 9) Out Normal Alarm Pump Laser Temperature Monitor (pin 10) Out Normal Alarm Reflected Output Power Monitor (pin 11) Out Normal Alarm Input Power Monitor (pin 19) Out Normal Alarm Pump Toggle Switch (pin 21) In Pumps OFF Pumps ON Analog Control Voltage (Within Normal Range) Analog Output Range Output Power Control Voltage (pin 5) 0~4.7 volts Input Power Control Voltage (pin 6) 0~4.7 volts V

4 MW Series EDFA Operation Mode The MW series of EDFA products has two basic modes of operation: automatic gain control (AGC) and automatic current control (ACC). Either mode can be set via the RS-232 interface. In addition, automatic power control (APC) can be provided as a customer optional mode. The factory default mode is AGC and it is stored in the microcontroller s permanent memory. The ACC mode is enabled during production to test the EDFA parameters. AGC - Operating Conditions (Normal Mode) 1. EDFA receives "switch on pump laser" command (A dis ) 2. The output return loss must be lower than the output return loss threshold The operating current of pump laser 1 (or pump laser 1 and pump laser 2) is adjusted automatically to keep the gain constant over a wide range of optical input. Changes in the output power correspond to changes in input power while the gain is held constant. 1. If the input signal is above the AGC maximum limit, the pump laser will operate at its maximum current in the range of 180 to 250 ma 2. If the input signal is below the AGC input threshold level, the pump laser will operate at its minimum current in the range of 30 to 50 ma 3. If there is no input signal, the pump laser will operate at its minimum current and the corresponding output ASE will be in the range of +3 to +5 dbm ACC - Operating Conditions (Factory Mode) 1. EDFA receives the "switch on the pump laser" command (A dis ) 2. The output return loss must be lower than the output return loss threshold Pump laser 1 (or pump laser 1 and pump laser 2) operates at the maximum working current whether or not an input signal is present. If the input signal is present, the EDFA produces the maximum gain. If the input signal is absent, the output level produced by ASE (amplified spontaneous emission) is about +10 dbm. Outline Drawing (all dimensions are in mm; drawings are not to scale) 1-22 V011

5 Block Diagram Optical Parameters (over the full operating temperature range) Parameter Minimum Typical Maximum Units Notes Wavelength (ITU-T G.692) nm Full C-Band dbm Booster Input Power dbm Inline dbm Preamplifer dbm Booster Saturated Output Power dbm Inline dbm Preamplifer db Booster Signal Gain db Inline db Preamplifer Gain Flatness db - Dynamic Gain Variation db - Optical Isolation db - Input Return Loss db UPC/APC Noise Figure db - Polarization Dependent Gain db - Polarization Mode Dispersion ps - Pump Leakage dbm - Reverse ASE Power - < dbm - Power Consumption W - V

6 Ordering Information M W X X X 0 X X - X X X Erbium-Doped Fiber Amplifier (EDFA) - MW Series Connector Type 0: No connector 1: FC/UPC (standard) 2: FC/APC 3: SC/UPC 4: SC/APC Pigtail Fiber Length 0: Standard length = 1 m (standard) 1: User specify Fiber Type 0: Standard single-mode (standard) 1: User specify Output Power 09: 9 dbm 17: 17 dbm 18: 18 dbm Operating Wavelength 0: Red Band (1545 to 1562nm) 1: Full Band (1530 to 1562nm) Product Series 5 Booster 6: Inline 7: Preamplifier Amplifier Type B: Booster L: Line P: Preamplifier The following table summarizes the product options and provides examples: Part Amplifier Input Power Output Power Gain Operation Dimension Number Type (dbm) (dbm) (db) Band (nm) (mm x mm x mm) MWB Booster -20 to Full 150 x 124 x 20 MWL Inline -28 to Full 150 x 124 x 20 MWP Preamplifier -28 to Full 150 x 124 x 20 To order or for additional information, please contact us at: Phone: Fax: Web: All data listed in this specification sheet is subjected to change without notice. Nanovation reserves the right to revise or update the data sheet. Copyright 2001 by Nanovation Technologies Safety Information and Handling Precautions EDFAs are class III laser products. Please read carefully the following safety information prior to handling and installing. The signal output of the pump laser and EDFA is invisible, yet it can be of high power level and therefore can cause damage to the eyes or skin. Please do not look at the fiber cross section directly without protection devices. There are precision optical devices inside the EDFA; therefore extreme care should be taken not to impose excess vibration or shaking. Care should also be taken in handling the pigtail fibers since they are easily broken. There are static sensitive devices inside the EDFA, please make sure proper grounding and electrical power connection Do not attempt to open the EDFA by any unauthorized personnel. Please contact Nanovation technical support for assistance. V011

Product Specification

Product Specification Product Specification M7300CD Variable Gain EDFA, 17 dbm OP, 15-30 db Gain PN: FOA-M7300CD-EVG1C-AA002 Document No.: 1213704 Revision: A00 Date: 01-Apr-14 Customer: General Product Features Variable Gain

More information

PONA Rack Mounted Erbium Doped Fiber Amplifier. User s Manual r001 August 30, W. Chestnut St Alhambra, CA 91803

PONA Rack Mounted Erbium Doped Fiber Amplifier. User s Manual r001 August 30, W. Chestnut St Alhambra, CA 91803 PONA 2114-2127 Rack Mounted Erbium Doped Fiber Amplifier User s Manual 21061785r001 August 30, 2005 EMCORE CORPORATION 2015 W. Chestnut St Alhambra, CA 91803 Tel: (626) 430-4000 Fax: (505) 430-4060 www.emcore.com

More information

LaserPlus Model LP-OA EDFA OPERATING MANUAL

LaserPlus Model LP-OA EDFA OPERATING MANUAL LaserPlus Model LP-OA EDFA OPERATING MANUAL 24926 Highway 108 Sierra Village, CA 95346 Phone: (800) 545-1022 Fax: (209 586-1022 025-370571 Rev. X1 E-Mail: sales@olsontech.com 04/13/11 TABLE OF CONTENTS

More information

OTEB-CO-B EDFA WITHOUT SNMP INSTRUCTION MANUAL

OTEB-CO-B EDFA WITHOUT SNMP INSTRUCTION MANUAL OTEB-CO-B EDFA WITHOUT SNMP INSTRUCTION MANUAL Phone: (209) 586-022 (800) 545-022 Fax: (209) 586-026 E-Mail: salessupport@olsontech.com www.olsontech.com OTEB-CO-B (No SNMP) Rev. X7 /7/200 SAFETY WARNINGS

More information

PureGain TM 2600 Variable Gain EDFA for Metropolitan Networks

PureGain TM 2600 Variable Gain EDFA for Metropolitan Networks FEATURES Variable Gain Amplifier with or without Mid-Stage Fully Integrated Control Electronics with State-of-the-Art Transient Suppression Control Three Standard Configurations Mk I: 17 dbm VGA (Variable

More information

Product Specification

Product Specification Product Specification R9300TH Hybrid Raman-EDFA, Dual Raman Pump PN: FOA-R9300TH-HBR3C-AA001 Document No.: 1213710 Revision:A0 0 Date: 18-May-14 Customer: General Product Features Integrated Raman and

More information

MINI2. Inno Mini 2 Specs Provided by MOST ACCURATE COMPACT OTDR

MINI2. Inno Mini 2 Specs Provided by  MOST ACCURATE COMPACT OTDR Inno Mini 2 Specs Provided by www.aaatesters.com MOST ACCURATE COMPACT OTDR SOLA (Smart Optical Link Analyzer) 5 Touch Screen with Smart GUI 8GB Internal Storage with Internal SD Card & External USB Memory

More information

OPTICAL FIBER SOLUTIONS

OPTICAL FIBER SOLUTIONS RightWave Erbium-Doped Optical Fiber Critical component for the amplification of optical transmission signals A Furukawa Company Broad portfolio suited to diverse needs Proven product uniformity, quality

More information

CM97-xxx-7x. Cooled 980nm Pump Laser Module. Product Datasheet. Features. Applications

CM97-xxx-7x. Cooled 980nm Pump Laser Module. Product Datasheet. Features. Applications Cooled 980nm Pump Laser Module Features High output power, >1.0W kink free Fiber Bragg grating stabilization for wavelength locking over the entire operating conditions Hermetically sealed 10pin mini-butterfly

More information

USER MANUAL. WDM-D15xx.xx. Single Wavelength Add/Drop Module for DWDM

USER MANUAL. WDM-D15xx.xx. Single Wavelength Add/Drop Module for DWDM Rev. 0 USER MANUAL WDM-D15xx.xx Single Wavelength Add/Drop Module for DWDM Network Electronics ASA Thorøya 3204 Sandefjord, Norway Phone: +47 33 48 99 99 Fax: +47 33 48 99 98 e-mail: support@network-electronics.com

More information

VIEW500 USER-FRIENDLY STANDARD OTDR

VIEW500 USER-FRIENDLY STANDARD OTDR USER-FRIENDLY STANDARD OTDR SOLA (Smart Optical Link Analyzer) 7 Touch Screen with Smart GUI 8GB Internal Storage with Internal SD Card & External USB Memory Built-In VFL, Light Source and OPM Fast Booting

More information

OPTICAL AMPLIFIERS SELECTION GUIDE

OPTICAL AMPLIFIERS SELECTION GUIDE OPTICAL AMPLIFIERS SELECTION DE Finisar offers a wide selection of optical amplifiers, ranging in optical and electrical specification parameters, and in a variety of form factors and communications interfaces.

More information

Cooled Butterfly 980nm Pump Laser Module

Cooled Butterfly 980nm Pump Laser Module Cooled Butterfly 980nm Pump Laser Module Features: High output power, up to 600mW kink free Polarization maintaining fiber pigtail Fiber Bragg grating stabilization for wavelength locking over the entire

More information

Features

Features Applications Features Support O-band, 1260~1340nm Band amplification Maximum output power can be achieved 13dBm; Support three working modes ACC, APC and AGC; Through RS232 or SNMP to progress Status monitoring

More information

VIEW500 FASTEST STANDARD OTDR

VIEW500 FASTEST STANDARD OTDR FASTEST STANDARD OTDR SOLA, Simplify The OTDR Test Process 7 Touch Screen with Smart GUI 8GB Internal Storage with Internal SD Card & External USB Memory Built-In VFL, Light Source and OPM Fast Booting

More information

RC801/803/ B 16E1 Fiber-Optic Multiplexer (Rev. M) User Manual. Raisecom Technology Co., Ltd. (04/2005)

RC801/803/ B 16E1 Fiber-Optic Multiplexer (Rev. M) User Manual. Raisecom Technology Co., Ltd. (04/2005) RC801/803/805-480B 16E1 Fiber-Optic Multiplexer (Rev. M) User Manual Raisecom Technology Co., Ltd. (04/2005) 1. Cautions Please read the following notices carefully before installing and using the device,

More information

Description. Features Standard OC-48 pin compatibility Narrow spectral linewidth Low noise Meets GR 468 reliability specifications

Description. Features Standard OC-48 pin compatibility Narrow spectral linewidth Low noise Meets GR 468 reliability specifications Description The DFB-XXX-BF-10-EC-Fx-Hx-N126 laser modules are designed for fiber optic sensor applications. The narrow linewidth and the option of using polarization maintaining optical fiber made it specially

More information

MINI2 MOST ACCURATE COMPACT OTDR

MINI2 MOST ACCURATE COMPACT OTDR MOST ACCURATE COMPACT OTDR SOLA, Simplify The OTDR Test Process 5 Touch Screen with Smart GUI 8GB Internal Storage with Internal SD Card & External USB Memory Built-In VFL and Light Source Fast Booting

More information

User Manual. Portable 4-Channel Laser Source Instrument in Small Benchtop. (QLDS-N series, version 1.0a. March 26, 2014)

User Manual. Portable 4-Channel Laser Source Instrument in Small Benchtop. (QLDS-N series, version 1.0a. March 26, 2014) User s Fiberprime, Inc. Portable 4-Channel Laser Source Instrument www.fiberprime.com Tel: 1-613-5964030 Email: info@fiberprime.com Fax: 1-613-8289398 Portable 4-Channel Laser Source Instrument in Small

More information

Attenuators. Fiber Optic Products Catalog. Singlemode Build Out Attenuators. Product Facts. Applications. Customizable Features. Available Collateral

Attenuators. Fiber Optic Products Catalog. Singlemode Build Out Attenuators. Product Facts. Applications. Customizable Features. Available Collateral Attenuators Build Out Attenuators Product Facts A range of fixed attenuation values. Standard values of 1 through 20 and 25dB UPC and APC offer Excellent Return Loss LC, SC, FC, ST, and D4 styles Attenuation

More information

Fiber Optics and Liquid Level Sensors Line Guide

Fiber Optics and Liquid Level Sensors Line Guide Fiber Optics and Liquid Level Sensors Line Guide Excellence, through every fiber. Honeywell Sensing and Control (S&C) offers fiber optic sensors manufactured with SERCOS (Serial Real-time Communication

More information

Product Specification

Product Specification Product Specification R9400SA UltraSpan ROPA Pump Unit 1600 mw Output Power, 3U PN: FOA-R9400SA-RPA6C-AA017 Document No.: 1215607 Revision: A00 Date: 16-Jun-14 Customer: General Product Features Fully

More information

Description. Features Standard OC-48 pin compatibility Narrow spectral linewidth Low noise Meets GR 468 reliability specifications

Description. Features Standard OC-48 pin compatibility Narrow spectral linewidth Low noise Meets GR 468 reliability specifications Description The DFB-XXX-BF-10-EC-Fx-Hx-N126 laser modules are designed for fiber optic sensor applications. The narrow linewidth and the option of using polarization maintaining optical fiber made it specially

More information

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED

More information

FPS CL Burst Mode SFF BIDI EPON ONU TRANSCEIVER(20Km)

FPS CL Burst Mode SFF BIDI EPON ONU TRANSCEIVER(20Km) FEATURES Dual Wavelength Bi-Directional Tx/Rx 1.25Gbps/1310nm Burst Mode Transmitter 1.25Gbps/1490nm CW Mode Receiver IEEE 802.3ah Compliant Single 3.3 Voltage Supply 2X10 SFF Package Outline Single Fiber

More information

RC802/ B 8E1 Modular Fiber-Optic Multiplexer (Rev. M) User Manual

RC802/ B 8E1 Modular Fiber-Optic Multiplexer (Rev. M) User Manual RC802/804-240B 8E1 Modular Fiber-Optic Multiplexer (Rev. M) User Manual Raisecom Technology Co., Ltd. (04/2005) 1. Cautions Please read the following notices carefully before installing and using the device,

More information

RION ORION TELECOM NETWORKS INC. E2, 2Mbps x 4 Opti-Multiplexer Integrated E2, OLTE and Multiplexer. Product Brochure & Data Sheet TELECOM NETWORKS

RION ORION TELECOM NETWORKS INC. E2, 2Mbps x 4 Opti-Multiplexer Integrated E2, OLTE and Multiplexer. Product Brochure & Data Sheet TELECOM NETWORKS RION TELECOM NETWORKS ORION TELECOM NETWORKS INC. E2, 2Mbps x 4 Opti-Multiplexer Integrated E2, OLTE and Multiplexer Product Brochure & Data Sheet Headquarters: Phoenix, Arizona 20100, N 51st Ave, Suite

More information

G155PU001S. Pigtailed 14-PIN DIL Laser Diode with TEC. FLMS Min. Typ. Max.

G155PU001S. Pigtailed 14-PIN DIL Laser Diode with TEC. FLMS Min. Typ. Max. G155PU001S TECHNICAL DATA Pigtailed 14-PIN DIL Laser Diode with TEC Features 1 mw 1550 nm MQW Laser Diode Module with cooler 14pin DIL package with single mode fiber output Applications Optical Communication

More information

AV6416 OTDR. Product Overview: Main Features:

AV6416 OTDR. Product Overview: Main Features: AV6416 OTDR Product Overview: AV6416 OTDR is a test instrument designed for FTTx. It s mainly used to measure the physical characteristics of optical fiber & cables, including length, transmission loss

More information

Description. Applications Sensor development Methane Gas detection External modulation. DFB-1XXX-BF-XX-CW-Fx-Hx-N REV 004 1

Description. Applications Sensor development Methane Gas detection External modulation. DFB-1XXX-BF-XX-CW-Fx-Hx-N REV 004 1 Description The DFB-1XXX-BF-XX-CW-Fx-Hx-N127 series of Multi-Quantum Well (MQW) Distributed Feedback (DFB) lasers have been designed specifically to satisfy the requirements of the sensor application.

More information

Set-Up Procedures. Before You Start

Set-Up Procedures. Before You Start Doc. 2272064, Rev. B Rel. 11/00 5000-ODA Amplifiers Ref. and Install. Manual Set-Up Procedures Before You Start In this section, you will find information about the following procedures: Checking the Optical

More information

T3/E3 Fiber Optic Line Drivers

T3/E3 Fiber Optic Line Drivers MT618A-ST-R3 January 2004 MT619A-ST-R2 MT620AE-R2 T3/E3 Fiber Optic Line Drivers CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) FREE technical

More information

LCP-6144A4EDRx. 10GBASE-SR SFP+ Optical Transceiver FEATURES. Description. Applications. RoHS compliant. Compliant to SFP+ Electrical MSA SFF-8431

LCP-6144A4EDRx. 10GBASE-SR SFP+ Optical Transceiver FEATURES. Description. Applications. RoHS compliant. Compliant to SFP+ Electrical MSA SFF-8431 10GBASE-SR SFP+ Optical Transceiver FEATURES RoHS compliant Compliant to SFP+ Electrical MSA SFF-8431 Compliant with SFF-8472 MSA Compliant with CPRI protocols for wireless base station Standard LC duplex

More information

OWL. Laser OWL Series. Operations Guide. Singlemode Light Sources. Optical Wavelength Laboratories. Date: October 1, 2015

OWL. Laser OWL Series. Operations Guide. Singlemode Light Sources. Optical Wavelength Laboratories. Date: October 1, 2015 Laser OWL Series Operations Guide Singlemode Light Sources OWL Optical Wavelength Laboratories Operations Guide Laser OWL and Laser OWL HP Singlemode Light Sources Date: October 1, 015 Version.5 Optical

More information

9 W, 15 W and 25 W Industrial Fiber Laser Systems IFL Series

9 W, 15 W and 25 W Industrial Fiber Laser Systems IFL Series COMMERCIAL LASERS 9 W, 15 W and 25 W Industrial Fiber Laser Systems IFL Series Key Features Diffraction-limited light delivered through fiber termination module Single transverse mode, collimated beam

More information

UC INSTRUMENTS GM8036 LASER SWEEP OPTICAL SPECTRUM ANALYZER (1525 ~ 1610 nm) Technical Specifications v1.01 March, 2011

UC INSTRUMENTS GM8036 LASER SWEEP OPTICAL SPECTRUM ANALYZER (1525 ~ 1610 nm) Technical Specifications v1.01 March, 2011 UC INSTRUMENTS GM8036 LASER SWEEP OPTICAL SPECTRUM ANALYZER (1525 ~ 1610 nm) Technical Specifications v1.01 March, 2011 GM8036 LASER SWEEP OPTICAL SPECTRUM ANALYZER (1525 ~ 1610 nm) UC INSTRUMENTS GM8036

More information

PONA 3000 Series High Power EDFA User s Guide

PONA 3000 Series High Power EDFA User s Guide USER S GUIDE, PONA 3000 PONA 3000 Series High Power EDFA User s Guide For more information on this and other products: Contact Sales at Ortel 626-293-3400, or visit www.ortel.com. 1of 18 User s Guide,

More information

EPON ONU Optical Transceiver SFF Module

EPON ONU Optical Transceiver SFF Module EPON ONU Optical Transceiver SFF Module SYFE420 Features Integrated Single fiber bi-directional optical subassembly SC receptacle optical interface 1310nm FP laser Burst-mode Transmitter and 1490nm PIN

More information

Agilent 81663A DFB Laser 8165xA Fabry-Perot Lasers

Agilent 81663A DFB Laser 8165xA Fabry-Perot Lasers DFB Laser 8165xA Fabry-Perot Lasers Data Sheet Introduction The high power DFB Laser Source modules are best suited for optical amplifier test and DWDM system test applications. The Fabry-Perot Laser Sources

More information

LCP-10G3B4HDR(T)-G. 10GBASE-LR Lite SFP+ Optical Transceiver. Description. Applications. Performance FEATURES. RoHS compliance

LCP-10G3B4HDR(T)-G. 10GBASE-LR Lite SFP+ Optical Transceiver. Description. Applications. Performance FEATURES. RoHS compliance 10GBASE-LR Lite SFP+ Optical Transceiver FEATURES RoHS compliance Compliant with SFP transceiver SFF-8472 MSA specification 1310nm FP laser Built-in digital diagnostic monitoring function Compliant with

More information

Fire Control Panels. Multiple Signal Fiber Optic Modems and Accessories for Panel and Remote Mounting. Features. Operation.

Fire Control Panels. Multiple Signal Fiber Optic Modems and Accessories for Panel and Remote Mounting. Features. Operation. UL, ULC Approved* Fire Control Panels Multiple Signal Fiber Optic Modems and Accessories for Panel and Remote Mounting Features Converts multiple fire alarm communications signals into a single fiber optic

More information

Analog Input Module IC670ALG630

Analog Input Module IC670ALG630 1 IC670ALG630 The Thermocouple (IC670ALG630) accepts 8 independent thermocouple or millivolt inputs. Module features include: Self calibration Two data acquisition rates based on 50 Hz and 60 Hz line frequencies

More information

CWDM-1-8 / 9-16 CWDM-1-8-M / 9-16-M CWDM-1-8-L / CWDM-9-16-L

CWDM-1-8 / 9-16 CWDM-1-8-M / 9-16-M CWDM-1-8-L / CWDM-9-16-L CWDM-1-8 / 9-16 CWDM-1-8-M / 9-16-M CWDM-1-8-L / CWDM-9-16-L 9-channel CWDM multiplexer and demultiplexer / multi mode (-M) / -low-loss (-L) User manual Nevion Nordre Kullerød 1 3241 Sandefjord Norway

More information

LCP-10G3B4QDRx-G. 10GBASE-LR SFP+ Optical Transceiver FEATURES. Description. Applications. Performance. RoHS compliant

LCP-10G3B4QDRx-G. 10GBASE-LR SFP+ Optical Transceiver FEATURES. Description. Applications. Performance. RoHS compliant 10GBASE-LR SFP+ Optical Transceiver FEATURES RoHS compliant Compliant to SFP+ Electrical MSA SFF-8431 Compliant with SFF-8472 MSA Standard LC duplex fiber-optic connector I 2 C for integrated Digital Optical

More information

Four channel video link For low cost video transmission

Four channel video link For low cost video transmission User Manual Four channel video link For low cost video transmission CFO First Mile series consist of fi bre optic modems which provide a high quality and losless video transmission for variety of CCTV

More information

FCX-11AB5-3XX-XX 155Mbps BIDI SFP TRANSCEIVER(100Km)

FCX-11AB5-3XX-XX 155Mbps BIDI SFP TRANSCEIVER(100Km) FEATURES LC or SC receptacle optical interface compliant Single 3.3V power supply Hot-pluggable Uncooled 1490nm DFB laser transmitter Receiver loss of signal output AC/AC Coupling according to MSA Transmitter

More information

GPON OLT Optical Transceiver SFP Module RTXM RTXM Features

GPON OLT Optical Transceiver SFP Module RTXM RTXM Features GPON OLT Optical Transceiver SFP Module RTXM167-522 Features Integrated Single fiber bi-directional optical subassembly 1310nm Burst-mode APD/TIA receiver and 1490nm Continuous DFB laser Transmitter (with

More information

condition monitoring WP4086 Condition Monitoring System The WP4086 CMS System surveys vibrations with up to 8 external accelerometers

condition monitoring WP4086 Condition Monitoring System The WP4086 CMS System surveys vibrations with up to 8 external accelerometers WP4086 Condition Monitoring System WP4086 Condition Monitor Accelerometer Measuring Points The WP4086 CMS System surveys vibrations with up to 8 external accelerometers Real-time sample, calculation and

More information

WP4086 Condition Monitoring System

WP4086 Condition Monitoring System WP4086 Condition Monitoring System WP4086 Condition Monitor The WP4086 CMS System surveys vibrations with up to 8 external accelerometers Real-time sample, calculation and storage of vibration signals,

More information

Clearlite Photonic Fibers

Clearlite Photonic Fibers Clearlite Photonic Fibers Fiber Name Operating Wavelength MFD at Operating Wavelength Beat Length at Operating WL Clad/Coating Diameter Order by Part Number TruePhase 980 Micro TruePhase 980 400 TruePhase

More information

Fiber Optics for Todays Industry Applications

Fiber Optics for Todays Industry Applications Hands-On Fiber Optics for Todays Industry Applications (A Non-Telephone Company Course) Course Description This Hands-On course is designed to provide technicians with a practical understanding and Hands-On

More information

Fire Control Panels. Multiple Signal Fiber Optic Modems and Accessories for 4120 Network. UL, ULC, CSFM Listed; FM Approved* Features

Fire Control Panels. Multiple Signal Fiber Optic Modems and Accessories for 4120 Network. UL, ULC, CSFM Listed; FM Approved* Features Fire Control Panels UL, ULC, CSFM Listed; FM Approved* Features Compatible with Simplex 4120 Network Converts multiple 4120 network communications signals into a single fiber optic link to: Multiplex audio

More information

Noyes OFL 250B Specs Provided by

Noyes OFL 250B Specs Provided by Noyes OFL 250B Specs Provided by www.aaatesters.com OFL 250 Handheld OTDR The Noyes OFL 250 from AFL Telecommunications is a single-mode OTDR with an integrated Optical Power Meter (OPM), Source (OLS),

More information

Optical Return Loss Measurement by Gregory Lietaert, Product Manager

Optical Return Loss Measurement by Gregory Lietaert, Product Manager White Paper Optical Return Loss Measurement by Gregory Lietaert, Product Manager Introduction With the increasing frequency of high-speed transmission systems and DWDM deployment, optical return loss (ORL)

More information

SECTION 1: STARTING 1.1 UNPACKING AND INSPECTION

SECTION 1: STARTING 1.1 UNPACKING AND INSPECTION SECTION 1: STARTING 1.1 UNPACKING AND INSPECTION Upon receipt of the laser system, inspect the shipping containers for gross external damage. Unpack the unit and inspect for internal damage. If any damage

More information

FIRERAY 5000 range USER GUIDE

FIRERAY 5000 range USER GUIDE FIRERAY 5000 range USER GUIDE 0044-003-04 IMPORTANT PLEASE NOTE: The beam path MUST be kept clear of obstructions at all times! Failure to comply may result in the Detector initiating a Fire or Fault signal.

More information

Fiber Optical Multiplexer

Fiber Optical Multiplexer Fiber Optical Multiplexer 8x E1, 1x Fast Ethernet, Hotline, 1x Fiber optic XL-FMUX4E1 User s Manual Thank you for using XtendLan s products. This manual will show you how to install and use this product.

More information

DWDM OTDR with Tunable Laser MTP-200-D100. Hand-held High Performance OTDR. Series

DWDM OTDR with Tunable Laser MTP-200-D100. Hand-held High Performance OTDR. Series MTP-200-D100 Hand-held High Performance OTDR DWDM OTDR with Tunable Laser Series Multi-Function and High Performance OTDR Testing 96 C-band wavelengths Dynamic range up to 38dB Short zone: EDZ 1m, ADZ

More information

MADE FOR THE TRADE! FIBER OPTIC. professional. XL fibertools Series. instruments

MADE FOR THE TRADE! FIBER OPTIC. professional. XL fibertools Series. instruments MADE FOR THE TRADE! professional FIBER OPTIC XL fibertools Series instruments XL fibertools Series Instruments Designed for Fiber Optic Cable Testing. The XL fibertools are designed for the professional

More information

OPR Power Series AC to DC POWER SUPPLY SERIES WITH REMOTE MANAGEMENT AND ALARM SYSTEMS. Model Nos. OPR200-24S / OPR200-24R. Manual

OPR Power Series AC to DC POWER SUPPLY SERIES WITH REMOTE MANAGEMENT AND ALARM SYSTEMS. Model Nos. OPR200-24S / OPR200-24R. Manual OPR Power Series AC to DC POWER SUPPLY SERIES WITH REMOTE MANAGEMENT AND ALARM SYSTEMS Model Nos. OPR200-24S / OPR200-24R Manual Revision F May 2010 Optimal Power Supplies LLC www.optimal-power.com i PROPRIETARY

More information

RF SCOUT PLUS INSTRUCTION MANUAL. Dielectric, LLC 22 Tower Rd. Raymond, ME Phone: January 2015, Rev B 1

RF SCOUT PLUS INSTRUCTION MANUAL. Dielectric, LLC 22 Tower Rd. Raymond, ME Phone: January 2015, Rev B 1 RF SCOUT PLUS INSTRUCTION MANUAL Dielectric, LLC 22 Tower Rd. Raymond, ME 04071 Phone: 800.341.9678 www.dielectric.com 21 January 2015, Rev B 1 WARNING Powering RF sensors above +30dBm (1W) will cause

More information

AE2200 FTTx Multi-Function Meter

AE2200 FTTx Multi-Function Meter AE2200 FTTx Multi-Function Meter Key Benefits Future-proof, all-in-one solution includes optical, cable TV analysis, and metallic testing for verifying the installation of FTTx, RFoG and RF PON networks

More information

HRX Technical Manual. Version 1.2

HRX Technical Manual. Version 1.2 HRX 5000 Technical Manual Version 1.2 Contents: Specification...2 Connectors...5 RS-485 Network Connectors (J6 and J7)...5 RS-232 to Printer (J19)...6 RS-232 to PC (J8)...7 TCP/IP...8 Power (J21)...9 Fire

More information

HOA1888 Series. Infrared Assemblies Wide Gap Transmissive Sensor. MICRO SWITCH Sensing and Control

HOA1888 Series. Infrared Assemblies Wide Gap Transmissive Sensor. MICRO SWITCH Sensing and Control Wide Gap Transmissive Sensor HOA1888 Series FEATURES Choice of phototransistor or photodarlington output Visible ambient light and dust protective filter 12 mm (0.47 in.) slot width Snap-in housing The

More information

Electro Optical Components, Inc Skylane Boulevard, Santa Rosa, CA Toll Free: 855-EOC

Electro Optical Components, Inc Skylane Boulevard, Santa Rosa, CA Toll Free: 855-EOC Electro Optical Components, Inc. 546 Skylane Boulevard, Santa Rosa, CA 9543 Toll Free: 855-EOC-63 www.eoc-inc.com info@eoc-inc.com PROFILE BEIJING REALLIGHT TECHNOLOGY CO., LTD Address:3rd Floor, #1 Building,

More information

The User Manual. 1550nm CATV ERBIUM-DOPED FIBER AMPLIFIER

The User Manual. 1550nm CATV ERBIUM-DOPED FIBER AMPLIFIER The User Manual 1550nm CATV ERBIUM-DOPED FIBER AMPLIFIER Our module light pumped laser and Erbium-Doped Fiber is used by the original binding compontfrom USA. We have reliable optical light power output

More information

Model ID-441-C InGaAs Near Infrared Detector with Preamplifier and Thermoelectric Cooler Operating Instructions

Model ID-441-C InGaAs Near Infrared Detector with Preamplifier and Thermoelectric Cooler Operating Instructions 15 Discovery Way, Acton, MA 01720 Phone: (978)263-3584, Fax: (978)263-5086 Web Site: www.piacton.com Model ID-441-C InGaAs Near Infrared Detector with Preamplifier and Thermoelectric Cooler Operating Instructions

More information

Rack Mount High-Power EDFA Installation Guide

Rack Mount High-Power EDFA Installation Guide Rack Mount High-Power EDFA Installation Guide OTEA-CL Series 025-000532 Rev 2 31 Mar 2009 Notices The information contained in this document is subject to change and revision without notice. Olson Technology,

More information

Danfoss gas detection units

Danfoss gas detection units Data sheet Danfoss gas detection units Types GD Premium, Premium+, Premium Duplex, Premium Remote, Premium Flex and Premium Uptime The Premium line gas detection units are used for monitoring and warning

More information

MTTplus Modular Test Platform

MTTplus Modular Test Platform MTTplus-410 Fiber Optics Test Module 2017 MTTplus Modular Test Platform The Fiber Optics module for the VeEX MTTplus supports a full range of test functions including OTDR, OPM, Light Source and VFL. Geo

More information

I/A Series 716C 1/16 DIN Temperature Controller

I/A Series 716C 1/16 DIN Temperature Controller Product Specifications I/A Series 716C 1/16 DIN Temperature Controller PSS 2C-1B5 A The Foxboro 716C is a powerful compact, 1/16 DIN, microprocessor-based temperature controller that offers a variety of

More information

Datasheet Palm OTDR. Product Summaries

Datasheet Palm OTDR. Product Summaries Datasheet Palm OTDR AV6416 palm OTDR is the newest instrument designed for testing FTTx network. It s mainly used to measure the physical characteristics of optical fiber under test, such as the length,

More information

EOTec 2000 ControlNet Fiber Optic SHR/DSHR Communications Modules* With Support for Single and Dual Channel Self-Healing Rings

EOTec 2000 ControlNet Fiber Optic SHR/DSHR Communications Modules* With Support for Single and Dual Channel Self-Healing Rings EOTec 2000 ControlNet Fiber Optic SHR/DSHR Communications Modules* With Support for Single and Dual Channel Self-Healing Rings Key Features Single and Dual Channel Self Healing Rings for High Reliability

More information

Fiber Optic and CAT 5, 6, 7 and 8 Installer Premise Cabling

Fiber Optic and CAT 5, 6, 7 and 8 Installer Premise Cabling Hands-On Fiber Optic and CAT 5, 6, 7 and 8 Installer Premise Cabling Certification Course Description This Hands-On course is customized to give Technicians the confidence and skills to maintain Fiber

More information

FTBx-740C-DWC TUNABLE OTDR C-BAND DWDM METRO ETHERNET LINK CHARACTERIZATION

FTBx-740C-DWC TUNABLE OTDR C-BAND DWDM METRO ETHERNET LINK CHARACTERIZATION C-BAND DWDM METRO ETHERNET LINK CHARACTERIZATION GLOBAL PORTABLE FIBER OPTIC TEST EQUIPMENT MARKET LEADERSHIP AWARD NEW OTDR GENERATION Tunable DWDM OTDR for testing through MUX/DEMUX channels to provide

More information

DHM5150 Human Motion Sensor Module User Manual

DHM5150 Human Motion Sensor Module User Manual DHM5150 Human Motion Sensor Module User Manual Version: 1.0.2 February 2005 Table of Contents I. Introduction 2 II. Operations 2 II.1. Theory of Operation 2 II.2. Running as Part of WiRobot System 3 II.3.

More information

VePAL FX300 Fiber Expert OTDR

VePAL FX300 Fiber Expert OTDR VePAL FX300 Fiber Expert OTDR Compact, Mini OTDR for Access Fiber Deployments VeEX FX300 Fiber Expert is a lightweight, handheld mini OTDR ideally suited for the installation and troubleshooting of FTTx,

More information

AUTO SWITCH ALARM PS1 PS2 CH2 MANUAL REMOTE HISTORY ALARM ONLINE AUTO MANUAL SELECT SWITCH RESET

AUTO SWITCH ALARM PS1 PS2 CH2 MANUAL REMOTE HISTORY ALARM ONLINE AUTO MANUAL SELECT SWITCH RESET Instruction Manual Model 1582-125L 1:1 Switch February 2017, Rev. 0 CH1 HISTORY LINE HISTORY RESET AUTO MANUAL SELECT CH2 HISTORY LINE RESET MANUAL REMOTE AUTO PS1 PS2 MODEL 1582 CROSS TECHNOLOGIES INC.

More information

palmotdr Series Handheld OTDR

palmotdr Series Handheld OTDR palmotdr Series Handheld OTDR Most Compact High-Performance OTDR Comprehensive fiber applications, ideal for LAN/WAN/FTTx certification & trouble-shooting: SM: 1310/1490/1550, 1625/1650nm (with filter),

More information

Dual SDI Optical to Electrical Converter

Dual SDI Optical to Electrical Converter Flashlink User Manual SDI-OE-2 Dual SDI Optical to Electrical Converter network-electronics.com Rev. 3 Network Electronics ASA Thorøya P.O. Box 1020 Sandefjord, Norway Phone: +47 33 48 99 99 Fax: +47 33

More information

G4 Pulsed Fiber Laser

G4 Pulsed Fiber Laser G4 Pulsed Fiber Laser OEM Safety and System Integration Manual Module types C1 and C2 Module type C1 - fitted with IBeam1 delivery optic Module type C2 - fitted with IBeam2 delivery optic 1 1 Preface Definition

More information

M210 Multifunction Micro OTDR

M210 Multifunction Micro OTDR Test, Troubleshoot and Document Single-mode and Multimode Fiber Networks Features 30 db dynamic range single-mode 16-hour battery life Remote display capable Touch and Test intuitive user interface New

More information

CATALOGUE LASER POINTERS

CATALOGUE LASER POINTERS CATALOGUE LASER POINTERS SM.PROX SRL Via della Beverara 13/A - 40131 Bologna - Italy Tel. +39 051 6350755 - Fax +39 051 6353462 Edition October 2014 With the publication of this catalogue all former editions

More information

4120 Fire Alarm Network Reference

4120 Fire Alarm Network Reference 4120 Fire Alarm Network Reference Features Autocall 4120 Fire Alarm Network communications are available for wired or fiber optic connections Wired communications are available on Network Interface Cards

More information

We are IntechOpen, the world s leading publisher of Open Access books Built by scientists, for scientists. International authors and editors

We are IntechOpen, the world s leading publisher of Open Access books Built by scientists, for scientists. International authors and editors We are IntechOpen, the world s leading publisher of Open Access books Built by scientists, for scientists 3,900 116,000 120M Open access books available International authors and editors Downloads Our

More information

Motorised Infrared Optical Beam Smoke Detector. User Guide

Motorised Infrared Optical Beam Smoke Detector. User Guide Motorised Infrared Optical Beam Smoke Detector User Guide EN 1. General Information 50cm 50cm 8-100m Ensure clear line of sight from Detector to Reflector Mount on solid surfaces (structural wall or girder)

More information

INTERNATIONAL TELECOMMUNICATION UNION SERIES L: CONSTRUCTION, INSTALLATION AND PROTECTION OF CABLES AND OTHER ELEMENTS OF OUTSIDE PLANT

INTERNATIONAL TELECOMMUNICATION UNION SERIES L: CONSTRUCTION, INSTALLATION AND PROTECTION OF CABLES AND OTHER ELEMENTS OF OUTSIDE PLANT INTERNATIONAL TELECOMMUNICATION UNION ITU-T L.36 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU (10/98) SERIES L: CONSTRUCTION, INSTALLATION AND PROTECTION OF CABLES AND OTHER ELEMENTS OF OUTSIDE PLANT

More information

MADE FOR THE TRADE! FIBER OPTIC. professional. XL fibertools Series. instruments

MADE FOR THE TRADE! FIBER OPTIC. professional. XL fibertools Series. instruments MADE FOR THE TRADE! FIBER OPTIC professional XL fibertools Series instruments XL fibertools Series Instruments Designed for Fiber Optic Cable Testing. The XL fibertools are designed for the professional

More information

M210 Multifunction Micro OTDR

M210 Multifunction Micro OTDR Test, Troubleshoot and Document Single-mode and Multimode Fiber Networks Features 30 db dynamic range single-mode 16-hour battery life Remote display capable Touch and Test intuitive user interface New

More information

DDT-4691 & DDR ASI / SD-SDI 8 Channel Mux Fibre Optic Link. User Manual. IRT Electronics Pty Ltd

DDT-4691 & DDR ASI / SD-SDI 8 Channel Mux Fibre Optic Link. User Manual. IRT Electronics Pty Ltd ASI / SD-SDI 8 Channel Mux Fibre Optic Link User Manual Revision 00 ASI / SD-SDI 8 Channel Mux Fibre Optic Link Revision History: Revision Date By Change Description Applicable to: 00 03/06/2014 AL Original

More information

Single Channel Video Receive Unit with two Bi-directional Data Channels and one Bi-directional Alarm Channel for a Multimode Fibre Link

Single Channel Video Receive Unit with two Bi-directional Data Channels and one Bi-directional Alarm Channel for a Multimode Fibre Link AMG5614A3 Instruction Manual Single Channel Video Receive Unit with two Bi-directional Data Channels and one Bi-directional Alarm Channel for a Multimode Fibre Link The AMG5614A3 is a standalone one channel

More information

Hands-On Fiber Optics ISP/OSP - Advanced Combo- Tech

Hands-On Fiber Optics ISP/OSP - Advanced Combo- Tech Hands-On Fiber Optics ISP/OSP - Advanced Combo- Tech Course Description This Hands-On 3-day course has been customized to provide technicians with a practical understanding of fiber optic theory and fiber

More information

FiberSensor Fiber Optic Intrusion Detection System (IDS)

FiberSensor Fiber Optic Intrusion Detection System (IDS) FiberSensor Fiber Optic Intrusion Detection System (IDS) OPERATION & INSTALLATION MANUAL Dec 2009, Issue 3 1 Table of Contents 1.0 PRECAUTIONS... 2 2.0 GETTING STARTED... 3 System Components... 3 Operating

More information

CDR-AL Room CO 2 Traffic Light Alarm Units and Sensors

CDR-AL Room CO 2 Traffic Light Alarm Units and Sensors Product sheet SN1.402 Type CDR-AL CDR-AL Room CO 2 Traffic Light Alarm Units and Sensors CDR-AL sensors are designed to detect carbon dioxide concentration and temperature in the room spaces. The units

More information

IF-L/RF Protection Switch

IF-L/RF Protection Switch Instruction Manual Model 1582-1152 IF-L/RF Protection Switch August 2014, Rev. 0 CH1 HISTORY ALARM LINE HISTORY RESET AUTO MANUAL SELECT CH2 HISTORY ALARM LINE RESET MANUAL REMOTE AUTO ALARM PS1 PS2 MODEL

More information

Instruction Manual ID-442 Infrared Detector 442-1A Temperature Controller Preamplifier

Instruction Manual ID-442 Infrared Detector 442-1A Temperature Controller Preamplifier 530 Main Street, Acton, MA 01720 Phone: (978)263-3584, Fax: (978)263-5086 Web Site: www.acton-research.com Instruction Manual ID-442 Infrared Detector 442-1A Temperature Controller 442-2 Preamplifier Ver.2.0

More information

Fibre Specification Standards

Fibre Specification Standards Fibre Specification Standards User Manual The most important thing we build is trust Cobham Wireless - Coverage Table of Contents 1. Single-mode Fibre to ITU-T Recommendation G.652 3 2. SC/APC Mated Pair

More information

Datasheet: K-22 LO Sensor

Datasheet: K-22 LO Sensor Datasheet: K-22 LO Sensor The K- 22 LO is a CO2 sensor module designed to be built- in into stationary ventilation equipment, such as window vent or duct exhaust actuators, serving as a linear transmitter

More information

Motorised Infrared Optical Beam Smoke Detector. User Guide

Motorised Infrared Optical Beam Smoke Detector. User Guide Motorised Infrared Optical Beam Smoke Detector User Guide EN 1. General Information 50cm 50cm 8-100m Ensure clear line of sight from Detector to Reflector Mount on solid surfaces (structural wall or girder)

More information

Agilent E6000A E6003A Specs Provided by E6000C Mini-OTDR. Technical Data Sheet

Agilent E6000A E6003A Specs Provided by  E6000C Mini-OTDR. Technical Data Sheet Agilent E6000A E6003A Specs Provided by www.aaatesters.com E6000C Mini-OTDR Technical Data Sheet Specifications describe the instrument s warranted performance, measured with typical PC-type connectors.

More information