Flame Retardant EP/CPE POWER, CONTROL & INSTRUMENTATION CABLES

Transcription

1 Flame Retardant EP/CPE POWER, CONTROL & INSTRUMENTATION CABLES

2 FLAME RETARDANT EP/CPE TYPE TC OR TC-ER POWER CABLE Two Five Conductor + Ground (Two, Three & Four Conductor) 600 V Rated 90 C Conductor* Bare annealed copper conforming to ASTM B3 and Class B stranded in accordance with ASTM B8 *Also available in tinned copper Insulation Flame Retardant EP meeting the requirements of XHHW-2* *XLPE insulation available upon request RATINGS & APPROVALS Ground Bare or tinned copper provided on Two, Three & Four Conductor Cables Jacket A black, flame retardant, oil, abrasion, chemical and sunlight resistant thermoset CPE meeting UL 1277 n 90 C temperature rating n Conductors meet Type XHHW-2 per UL 44 n UL Listed as Type TC-ER (E123629) n Flame Retardant IEEE 1202/FT4 n Suitable for use in Class I, Div 2 and Zone 2 environments APPLICATION Type TC or TC-ER tray cable is permitted for use on power, lighting, control, and signal circuits; indoors or outdoors; in cable trays, raceways, direct burial in the ground or where supported in outdoor locations by a messenger wire; for Class 1 circuits as permitted in Article 725 of the NEC; and in cable trays in Class I, Division 2 hazardous locations in industrial establishments where the conditions of maintenance and supervision assure that only qualified persons will service the installation. Cables Marked TC-ER may also be used between a cable tray and the utilization equipment or device, when installed in accordance with NEC (7). FEATURES n Sunlight resistant. n For direct burial. n Insulated conductors are UL rated VW-1. n Insulation meets UL 1581, ICEA S (NEMA WC57) and ICEA S NEMA WC70 Type II n 130 C emergency overload rating n 90 C continuous rating in wet or dry locations n 250 C short circuit rating. n Resistant to moisture and most chemical atmospheres. n Thermal stability at elevated temperatures. n Flexible, easy to install and terminate. n Gas & vapor tight impervious to water and air n Grounding Conductor: Where indicated, bare or green insulated stranded copper per ASTM B-8 for sizes #8 AWG and smaller, compact round for sizes larger than #8 AWG per ASTM B-496 and in accordance with NEC Table downstream@nexans.com

3 TWO CONDUCTOR + GROUND FLAME RETARDANT EP/CPE TYPE TC OR TC-ER POWER CABLE Size Weight DC Resist. AC Resist. Inductive Voltage Drop Uninsulated AWG/ Part No. Diameter C, 60 Hz 90 C Grounding Cond. Ampacity kcmil (Inches) MFt) (Ohms/1k ft) (Ohms/1k ft) (Ohms/1k ft) (Volts/Amp/1k ft) Size AWG 90 C 75 C G G G G G G G G /0-216G /0-217G /0-218G /0-219G THREE CONDUCTOR + GROUND FLAME RETARDANT EP/CPE TYPE TC OR TC-ER POWER CABLE Size Weight DC Resist. AC Resist. Inductive Voltage Drop Uninsulated AWG/ Part No. Diameter C, 60 Hz 90 C Grounding Cond. Ampacity kcmil (Inches) MFt) (Ohms/1k ft) (Ohms/1k ft) (Ohms/1k ft) (Volts/Amp/1k ft) Size AWG 90 C 75 C G G G G G G G G /0-316G /0-317G /0-318G /0-319G G G G G Manufactured by Nexans AmerCable Fax:

4 FLAME RETARDANT EP/CPE TYPE TC OR TC-ER POWER CABLE Two Five Conductor + Ground (Two, Three & Four Conductor) 600 V Rated 90 C FOUR CONDUCTOR + GROUND FLAME RETARDANT EP/CPE TYPE TC OR TC-ER POWER CABLE Size Weight DC Resist. AC Resist. Inductive Voltage Drop Uninsulated AWG/ Part No. Diameter C, 60 Hz 90 C Grounding Cond. Ampacity kcmil (Inches) MFt) (Ohms/1k ft) (Ohms/1k ft) (Ohms/1k ft) (Volts/Amp/1k ft) Size AWG 90 C 75 C G G G G G G G G /0-416G /0-417G /0-418G /0-419G G G G G FIVE CONDUCTOR FLAME RETARDANT EP/CPE TYPE TC OR TC-ER POWER CABLE Size Weight DC Resist. AC Resist. Inductive Voltage Drop AWG/ Part No. Diameter C, 60 Hz 90 C Ampacity kcmil (Inches) MFt) (Ohms/1k ft) (Ohms/1k ft) (Ohms/1k ft) (Volts/Amp/1k ft) 90 C 75 C / / / Ampacities are based on Table (B)(16) of the National Electrical Code (NEC) for conductors rated 90 C, in a multi-conductor cable, at an ambient temperature of 30 C. The 75 C column is provided for additional information. The ampacities shown apply to open runs of cable, installation in any approved raceway. Derating for more than three current carrying conductors within the cable is in accordance with NEC Table (B)(3)(a). The ampacities shown also apply to cables installed in cable tray in accordance with NEC Section downstream@nexans.com

5 FLAME RETARDANT EP/CPE TYPE TC OR TC-ER INSTRUMENTATION CABLE Individually Shielded Pairs & Triads 600 V Rated 90 C Insulation Flame Retardant EP meeting the requirements of XHHW-2* *XLPE insulation available upon request RATINGS & APPROVALS n 90 C temperature rating n Conductors meet Type XHHW-2 per UL 44 n UL Listed as Type TC-ER (E123629) n Flame Retardant IEEE 1202/FT4 n Suitable for use in Class I, Div 2 and Zone 2 environments VALUES: 16 AWG Capacitance (nf/1000 feet) = 18 Inductance (mh/1000) = 0.22 Resistance (Ohms/1000 feet) = 2.62 (@ 20 C) 14 AWG Capacitance (nf/1000 feet) = 20 Inductance (mh/1000) = 0.21 Resistance (Ohms/1000 feet) = 4.19 (@ 20 C) Conductor* Bare annealed copper conforming to ASTM B3 and Class B stranded in accordance with ASTM B8 *Also available in tinned copper Pairs/ Triads Each pair/triad is twisted with a bare tinned drain wire. Each pair/triad is shielded with polyesterbacked aluminum foil tape to afford 100% coverage. Pair to pair, or triad to triad, isolation plus overall shielding is provided. Jacket A black, flame retardant, oil, abrasion, chemical and sunlight resistant thermoset CPE meeting UL 1277 APPLICATION Shielded instrumentation cables are designed for use on Class 1 Remote-Control Signaling circuits or where a 600V cable is desired, as instrumentation, process control, or computer cable transmitting signals at levels above 100 millivolts in circuits. They are designed for use indoors or outdoors; wet or dry locations; in cable trays; in raceways; supported by a messenger wire; for direct burial; in Class I, Division 2, Class II, Division 2 hazardous locations in industrial establishments where the conditions of maintenance and supervision assure that only qualified persons will service the installation. Cables Marked TC-ER may also be used between a cable tray and the utilization equipment or device, when installed in accordance with NEC (7). FEATURES n Sunlight resistant. n For direct burial (14 AWG). n Insulated conductors are UL rated VW-1. n Insulation meets UL 1581, ICEA S (NEMA WC57) and ICEA S NEMA WC70 Type II n 90 C continuous rating in wet or dry locations n 130 C emergency overload rating n 250 C short circuit rating. n Resistant to moisture and most chemical atmospheres. n Thermal stability at elevated temperatures. n Flexible, easy to install and terminate. n Gas & vapor tight impervious to water and air Size Part No. Diameter Weight AWG Pairs Triads (Inches) (lbs/mft) Manufactured by Nexans AmerCable Fax:

6 FLAME RETARDANT EP/CPE TYPE TC OR TC-ER CONTROL CABLE Multi-Conductor 600 V Rated 90 C Insulation Flame Retardant EP meeting the requirements of XHHW-2* *XLPE insulation available upon request RATINGS & APPROVALS Conductor* Bare annealed copper conforming to ASTM B3 and Class B stranded in accordance with ASTM B8 *Also available in tinned copper Jacket A black, flame retardant, oil, abrasion, chemical and sunlight resistant thermoset CPE meeting UL 1277 APPLICATION Type TC or TC-ER tray cable is permitted for use on power, lighting, control, and signal circuits; indoors or outdoors; in cable trays, raceways, direct burial in the ground or where supported in outdoor locations by a messenger wire; for Class 1 circuits as permitted in Article 725 of the NEC; and in cable trays in Class I, Division 2 hazardous locations in industrial establishments where the conditions of maintenance and supervision assure that only qualified persons will service the installation. Cables Marked TC-ER may also be used between a cable tray and the utilization equipment or device, when installed in accordance with NEC (7). FEATURES n Sunlight resistant. n For direct burial (14 AWG and larger). n Insulated conductors are UL rated VW-1. n Insulation meets UL 1581, ICEA S (NEMA WC57) and ICEA S NEMA WC70 Type II n 90 C continuous rating in wet or dry locations n 130 C emergency overload rating n 250 C short circuit rating. n Resistant to moisture and most chemical atmospheres. n Thermal stability at elevated temperatures. n Flexible, easy to install and terminate. n Gas & vapor tight impervious to water and air n 90 C temperature rating n Conductors meet Type XHHW-2 per UL 44 n UL Listed as Type TC-ER (E123629) n Flame Retardant IEEE 1202/FT4 n Suitable for use in Class I, Div 2 and Zone 2 environments downstream@nexans.com

7 FLAME RETARDANT EP/CPE TYPE TC OR TC-ER CONTROL CABLE Weight Size Part No Number of Diameter (lbs./ Ampacity AWG Conductors (Inches) MFt) 90 C 75 C Ampacities are based on Table (B)(16) of the National Electrical Code (NEC) for conductors rated 90 C, in a multi-conductor cable, at an ambient temperature of 30 C. The 75 C column is provided for additional information. The ampacities shown apply to open runs of cable, installation in any approved raceway. Derating for more than three current carrying conductors within the cable is in accordance with NEC Table (B)(3)(a). The ampacities shown also apply to cables installed in cable tray in accordance with NEC Section Equipment Grounding Conductor: Any conductor in these cables may be permanently re-identified during installation as the equipment grounding conductor in accordance with Section (B) of the NEC. Manufactured by Nexans AmerCable Fax:

8 EPR/CPE TYPE RHH OR RHW OR 2000 VOLTS POWER & CONTROL 90 C Limited Smoke (Sizes 2/0 and higher) EP/CPE Conductor* Bare, annealed copper conforming to ASTM B3 and Class B stranded, in accordance with ASTM B8 *Also available in tinned copper Jacket Flame retardant, oil and sunlight resistant Chlorinated Polyethylene (CPE) See below for jacket color options (Special order) RATINGS & APPROVALS SAVE TIME SAVE MONEY Separator Suitable separator tape provides easy stripping of insulation Insulation Ethylene-Propylene rubber (EPR) n ICEA S /NEMA WC-70: Nonshielded Power Cables Rated 2000 Volts or Less for the Distribution of Electrical Energy n UL Standard 44: Thermoset Insulated Wires & Cables, Types RHH, RHW-2. UL VW-1 n UL Standard 1685: Vertical Tray Fire propagation and Smoke Release Test for Electrical and optical Fiber Cables. (UL,ST-1) n MSHA P-184 n RoHS Compliant Order Your RHH or RHW-2 Cable with Factory Installed Connectors APPLICATION Type RHH or RHW-2 Power and Control Cables are recommended for general power and control applications. These cables may be used in generating plants, substations and industrial plants. Type RHH or RHW-2 may be used up to 90 C in dry or wet locations. These cables may be installed in wet or dry locations, indoors or outdoors, in raceways, underground ducts, cable tray (size 1/0 AWG and larger per NEC 392) or lashed to a messenger for aerial installation. FEATURES n A two layer composite of flame retardant, oil and sunlight resistant Chlorinated Polyethylene (CPE) outer layer and Ethylene-Propylene rubber (EPR) inner layer. The composite design provides significant diameter reductions compared to designs using full thickness jackets. n Suitable for continuous operating temperatures of 90 C, wet or dry n Sizes 1/0 AWG and larger listed and marked for CT use n UL listed as Sunlight Resistant n Insulation and jacket meet hazardous waste regulations, per Code of Federal Regulations 40 Section 261 (40CFR261) for characteristic lead content n Flame Resistance: FT-4/IEEE1202 for sizes 1/0 AWG and larger; UL VW-1 n Meets smoke release and other requirements of Vertical Cable Tray Test UL 1685 and is marked ST-1 for 2/0 AWG 750 kcmil downstream@nexans.com

9 TYPE RHH OR RHW VOLTS POWER AND CONTROL Part No Size AWG/ kcmil Minimum Wires per Conductor Insulation Thickness in. Jacket Thickness in. Outside Diameter in. Approx. Weight lbs. per *Ampacity 1,000 ft. 90 C 75 C / / / / TYPE RHH OR RHW VOLTS POWER AND CONTROL Part No Size AWG/ kcmil Minimum Wires per Conductor Insulation Thickness in. Jacket Thickness in. Outside Diameter in. Approx. Weight lbs. per *Ampacity 1,000 ft. 90 C 75 C / / / / * Ampacity Calculated with at 90 C conductor temperature and 30 C ambient air, per 2014 NEC Table (B)(17) Manufactured by Nexans AmerCable Fax:

10

11 CONDUCTOR ID Method #1-E2 per ICEA S Conductor Insulation Stripe Conductor Insulation Stripe 1st BLACK 19th ORANGE Blue 2nd RED 20th YELLOW Blue 3rd BLUE 21st BROWN Blue 4th ORANGE 22nd BLACK Orange 5th YELLOW 23rd RED Orange 6th BROWN 24th BLUE Orange 7th RED Black 25th YELLOW Orange 8th BLUE Black 26th BROWN Orange 9th ORANGE Black 27th BLACK Yellow 10th YELLOW Black 28th RED Yellow 11th BROWN Black 29th BLUE Yellow 12th BLACK Red 30th ORANGE Yellow 13th BLUE Red 31st BROWN Yellow 14th ORANGE Red 32nd BLACK Brown 15th YELLOW Red 33rd RED Brown 16th BROWN Red 34th BLUE Brown 17th BLACK Blue 35th ORANGE Brown 18th RED Blue 36th YELLOW Brown Method 4 of ICEA S Conductor Printing Details Conductor Printing Details 1st 1-ONE-1 5th 5-FIVE-5 2nd 2-TWO-2 6th 6-SIX-6 3rd 3-THREE-3 7th 7-SEVEN-7 4th 4-FOUR-4 8th 8-EIGHT-8 Manufactured by Nexans AmerCable Fax:

12 DOWNSTREAM OIL & GAS CABLES Nexans AmerCable is an ISO 9001 certified cable manufacturer that combines leading-edge manufacturing technology, innovative thinking, and high quality service to deliver the finest upstream oil & gas cable products available. Nexans AmerCable serves the world from our Oil & Gas Group headquarters in Houston, Texas. Our professional field engineers and sales force work with you to create innovative, cost effective project solutions. Industrial VFD Foil shielded, power cables engineered for use in variable frequency AC drive applications. Available in several constructions Industrial CIR Crush and Impact Resistant cables without external armoring CORFLEX Type MC-HL Cables Nexans Tray Cables Cables for wet or dry locations in cable trays, raceways, open air or direct burial Nexans Instrumentation Cables 300V & 600V Pairs and Triads CLICK HERE TO FOLLOW US! Nexans AmerCable West Little York Road - Building 1 - Suite Fax: downstream@nexans.com , AmerCable Incorporated 1_18