FOAM CHAMBER MODEL - FCA & FCA-S TECHNICAL DATA FEATURES APPLICATION. Carbon Steel Construction FCA-65, FCA-80 & FCA-100. Stainless Steel Construction

Transcription

1 FOAM CHAMBER MODEL - FCA & FCA-S TECHNICAL DATA MODELS FCA-65, FCA-80 & FCA-100 Carbon Steel Construction FCA-S 65, FCA-S 80 & FCA-S 100 Stainless Steel Construction INLET SIZE 65, 80, 100 NB WORKING Min 2.8 Kg/cm 2 (40 PSI) PRESSURE Max 7 Kg/cm 2 (100 PSI) FLANGE ANSI B16.5 Class 150# CONNECTION WEIGHT 65 NB Kg (Approx) 80 NB Kg 100 NB Kg VAPOUR SEAL 0.7 to 1.75 Kg/sq.cm. RUPTURE PRESSURE (10 PSI to 25 PSI) Running water/ water foam solution pressure at inlet of Foam Chamber MAXIMUM 0.07 Kg/sq.cm. (1.0 PSI) PERMISIBLE BACK PRESSURE ON VAPOUR SEAL VAPOUR SEAL Glass Deflector Solid or Split Deflector FINISH Red RAL 3000 APPROVAL UL Listed ORDERING a) Model & Size INFORMATION b) Flow & Pressure at inlet of each Foam Chamber c) Inlet, outlet flange specification d) Type of Deflector e) Foam concentrate used f) Tank number / Tag number FEATURES LISTED 4UT3 UL Listed Heavy duty welded construction with choice of Carbon Steel or Stainless Steel material Frangible Glass Vapour Seal Controlled Air Flow proportional to liquid flow for optimum foam quality and rupture of vapour seal in narrow pressure tolerances for increased reliability Field replaceable orifice plate fitted with Foam Chamber Interchangeable with HD Foam Chamber Model FC APPLICATION Foam Chamber is used in one of the most common application to protect vertical fixed roof (cone) liquid storage tanks, with or without internal floating roof with the low expansion foam system. The application of foam is on the basis that the risk comprises the total surface area of the fuel. The foam system design guidelines generally used are in accordance with NFPA-11, standard. Foam chambers are defined by NFPA-11 as Type II discharge outlets for delivering the foam to the surface of a flammable liquid. The Foam Chambers are widely used with the Inline Foam Inductor, Balance Pressure Foam Proportioning system, Bladder Tank Proportioner or Foam Tender. JUNE, 2014 PAGE 1 OF 6 HD 254

2 SPECIFICATION Foam Chamber is an air aspirating foam discharge device, covering wide range of flow from 150 to 2400 litres per minute at 2.8 to 7 kg/sq.cm. inlet pressure. The Foam Chamber contains a vapour seal to prevent the entry of vapour into the foam chamber and the foam solution pipe. Each foam chamber is supplied with an orifice plate, designed for the required flow and inlet pressure. The orifice is field replaceable in the event of change in design parameters. The foam is produced by introducing air into the foam solution stream. The inlet of foam chamber is designed to create venturi jet which draws air into the foam solution stream. The air is drawn into the foam solution through the holes located on the foam chamber covered with stainless steel screen to exclude nesting birds and insects. The aerated foam is directed into the deflector for the gentle application of the expanded foam. The deflectors are available in different models. On removal of cover plate from the top of the chamber allows the system to be tested and to draw a sample of the expanded foam, without removing the vapour seal or disconnecting the foam chamber from the tank. Frangible glass bursting disc (vapour seal) can be replaced by easily. The vapour seal is designed to rupture within 0.7 to 1.75 Kg/sq.cm. (10 to 25 PSI) pressure at inlet flange of Foam Chamber, as required by NFPA, UL & FM standard. The vapour seal will withstand maximum back pressure of 0.07 Kg/sq.cm. Bar (1.0 PSI) or equal to 686mm of water column as specified by API for welded storage tank. If the requirement exceeds 0.07 Kg/sq.cm. Bar (1.0 PSI) as in case of nitrogen blanketing system, then this equipment may not be suitable. The vapour seal is frangible glass. The vapour seal is supplied with holder and for spares it can be with or without holder. The O ring used for seal are Nitride rubber and optional Viton for polar solvent. SYSTEM DESIGN REQUIREMENT The NFPA-11, a standard for low expansion foam, provides the essential requirement of an appropriate designed foam pouring system, which are identified and outlined as below: The Foam Deflector is used with the Foam Chamber. The aerated foam from the Foam Chamber is directed in to the deflector for the gentle application of the expanded foam. The deflector reduces the expanded foam velocity and allows the foam to slide down the tank wall. (a) Number of Foam Chamber: The number of foam chambers required is determined by the tank diameter. Where two or more foam chambers are required, they shall be spaced equally around the tank periphery and each Foam Chamber shall be sized to deliver foam at an approximately same rate. Please refer graph to select the unit that will provide the required minimum foam solution application rate at the available operating pressure of the Foam Chamber. For minimum number of Foam Chamber requirement, kindly follow the recommendations as per NFPA/OISD/TAC or as per the governmental codes or ordinances wherever applicable. (b) Minimum Foam Solution Application Rate: The minimum foam solution application rate is the rate at which the water and foam concentrate in correctly proportioned ratio should be delivered to the surface of a storage tank under protection to control and extinguish the fire. For minimum application rate requirement, follow the recommendations as per NFPA/OISD/ TAC or governmental codes or ordinances wherever applicable. JUNE, 2014 PAGE 2 OF 6 HD 254

3 TESTING & MAINTENANCE Qualified and trained person must commission the system. After few initial successful tests, an authorized person must be trained to perform inspection and testing of the system. It is recommended to carry out physical inspection of the system regularly. The system must be fully tested at least once in a year or in accordance with applicable NFPA/OISD/TAC standards or in accordance with standards of the organization having local jurisdiction. Do not turn off the system or any valve to make repair or test the system, without placing a roving Fire Patrol in the area covered by the system. The Patrol should continue until the system is put back in service. Also inform the local security guard and control alarm station, so as to avoid false alarm. Each system is to be flushed properly. The vapour seal must be replaced if the system has been operated. Normal testing of the chamber can be carried out by removing the cover plate from the top of the chamber. This allows the system to draw a sample of the expanded foam without removing the vapour seal or disconnecting the Foam Chamber from the tank. The air screen is to be inspected periodically for the obstruction of air inlet holes. If any obstruction is noticed, remove the same and flush if necessary. It is recommended to have regular maintenance programme to inspect the Vapour Seal Chamber discharge area and deflector for possible deposit or obstruction. CAUTION Do not install Foam chambers on pressured storage tanks (Inert gas blanketed tanks) and storage tanks containing product which attack the foam chamber standard construction material. Maximum permissible back pressure on vapour seal is 0.07 Kg/sq.cm.2 (1.0 PSI) NOTE: 1. A PROVISION IS TO BE MADE FOR PRESSURE GAUGE MOUNTING AT INLET OF FOAM CHAMBER, WHICH MAY BE PLUGGED AFTER SUCCESSFUL COMMISSIONING OF THE SYSTEM. THIS WILL HELP TO ANALYSE THE SYSTEM WHILE COMMISSIONING. 2. REFER TO THE INDIVIDUAL FOAM LISTING FOR OPERATING LIMITATION WITH EACH FOAM CONCENTRATE AND FOAM CHAMBER. Selection of HD Foam Chamber: FOAM CHAMBER SIZE K - FACTOR 65 NB 89.6 TO NB TO NB TO To select the size of the Foam Chamber use the following formula: Q = K P Q = Total solution flow in litres per minute. K = Constant for Foam Chamber P = Inlet pressure in kg/sq.cm. JUNE, 2014 PAGE 3 OF 6 HD 254

4 FOAM CHAMBER C F2 8 7 B A F1 DIMENSIONS OF FOAM CHAMBER in millimeter (Approximate) PART LIST INLET OUTLET SIZE SIZE A B C F1 F2 65NB 100NB NB 150NB NB 200NB ITEM MATERIAL SPECIFICATON DESCRIPTION NO. FCA FCA-S 1 ORIFICE ASSEMBLY STAINLESS STEEL STAINLESS STEEL 2 INLET FLANGE STEEL STAINLESS STEEL 3 STRAINER ASSEMBLY STAINLESS STEEL STAINLESS STEEL 4 FOAM MAKING CHAMBER STEEL PIPE SS PIPE 5 FOAM CHAMBER STEEL STAINLESS STEEL 6 INSPECTION COVER STEEL STAINLESS STEEL 7 DISCHARGE PIPE STEEL PIPE SS PIPE 8 OUTLET FLANGE STEEL STAINLESS STEEL 9 VAPOUR SEAL ASSEMBLY GLASS GLASS NOTE: 1. Pipes used are ERW (Seamless Pipe are optional) 2. Foam chambers are open to atmosphere & do not have internal shutoff device,hence no hydrotest is offered during inspection. JUNE, 2014 PAGE 4 OF 6 HD 254

5 * * TYPICAL FOAM CHAMBER INSTALLATION WITH DEFLECTOR TYPICAL INSTALLATION OF FOAM CHAMBER WITH STUD FLANGED SPLIT DEFLECTOR FOAM CHAMBER OUTLET FLANGE GASKETS FOAM CHAMBER MODEL FCA TANK SHELL SPLIT DEFLECTOR MODEL SD MOUNTING PAD ASSEMBLY SPLIT DEFLECTOR INLET FLANGE STUD MOUNTING PAD STORAGE TANK NOTE: Stud Mounting Pad with gasket & split deflector are optional items. To be ordered separately. TANK CUTOUT FOR MOUNTING OF SPLIT DEFLECTOR PCD FLANGE OUTLINE RØ TYPE FOAM CHAMBER SIZE INLET FLANGE SIZE OUTLET FLANGE SIZE RØ PCD CUTOUT SIZE HOLE Ø d NO OF HOLES * FCA FCA Ø'd' FCA * BY INSTALLER TYPICAL INSTALLATION OF FOAM CHAMBER WITH STUD FLANGED TANK NOZZLE AND SOLID DEFLECTOR FOAM CHAMBER MODEL FCA 200 * * TANK NOZZLE (BY OTHERS) SOLID DEFLECTOR MODEL FD STORAGE TANK NOTE: GLASS VAPOUR SEAL WITH HOLDER (STANDARD SUPPLY) 1. Above dimensions are general guidelines only. The system designer can adopt the dimensions as per NFPA/TAC/OISD or as per the governing rules & ordinance having local jurdiction. 2. Tank Nozzle nutbolts & gasket are optional to be ordered separately. 3. Split deflector Model SD and solid deflector Model FD is standard supply in carbon steel material and optional in stainless steel. * * BY INSTALLER JUNE, 2014 PAGE 5 OF 6 HD 254

6 PRESSURE VS FLOW PERFORMANCE CHARACTERISTIC FOAM SOLUTION FLOW FLOW IN LPM FOAM SOLUTION FLOW FLOW IN LPM INLET PRESSURE (KG/SQ.CM) FCA & FCA-S 65 NB INLET PRESSURE (KG/SQ.CM) FCA & FCA-S 80 NB FOAM SOLUTION FLOW FLOW IN LPM INLET PRESSURE (KG/SQ.CM) FCA & FCA-S 100 NB LIMITED WARRANTY HD FIRE PROTECT PVT. LTD. hereby referred to as HD FIRE warrants to the original purchaser of the fire protection products manufactured by HD FIRE and to any other person to whom such equipment is transferred, that such products will be free from defect in material and workmanship under normal use and care, for two (2) years from the date of shipment by HD FIRE. Products or Components supplied or used by HD FIRE, but manufactured by others, are warranted only to the extent of the manufacturer s warranty. No warranty is given for product or components which have been subject to misuse, improper installation, corrosion, unauthorized repair, alteration or un-maintained. HD FIRE shall not be responsible for system design errors or improper installation or inaccurate or incomplete information supplied by buyer or buyer s representatives. HD FIRE will repair or replace defective material free of charge, which is returned to our factory, transportation charge prepaid, provided after our inspection the material is found to have been defective at the time of initial shipment from our works. HD FIRE shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product including damages for injury to person, damages to property and penalties resulting from any products and components manufactured by HD FIRE. HD FIRE shall not be liable for any damages or labour charges or expense in making repair or adjustment to the product. HD FIRE shall not be liable for any damages or charges sustained in the adaptation or use of its engineering data & services. In no event shall HD Fire s product liability exceed an amount equal to the sale price. The foregoing warranty is exclusive and in lieu of all other warranties and representation whether expressed, implied, oral or written, including but not limited to, any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled. NOTICE : The equipment presented in this bulletin is to be installed in accordance with the latest publication standards of NFPA or other similar organisations and also with the provision of government codes or ordinances wherever applicable. The information provided by us are to the best of our knowledge and belief, and are general guidelines only. Site handling and installation control is beyond our reach. Hence we give no guarantee for result and take no liability for damages, loss or penalties whatsoever, resulting from our suggestion, information, recommendation or damages due to our product. Product development is a continuous programme of HD FIRE PROTECT PVT. LTD. and hence the right to modify any specification without prior notice is reserved with the company. HD FIRE PROTECT PVT. LTD. Protecting What Matters Most to You C-3/6, THE NANDANVAN IND. ESTATE, L.B.S. MARG, THANE , INDIA. PHONES : + (91) FAX : +(91) info@hdfire.com WEBSITE : JUNE, 2014 PAGE 6 OF 6 HD 254

7 FOAM POURER Foam Pourers are UL Listed with FOAM MAKER Model FM-A & FM-AS, (refer catalogue HD 255) Tank seal pouring system for internal floating roof storage tank. MODEL : FP-55 & FP-S-55 DIMENSION in millimetre (Approximate) SIZE A B C 80 NB NB A C B FP-55 is carbon steel material & FP-S-55 is in stainless steel 304/316 material. LIMITED WARRANTY HD FIRE PROTECT PVT. LTD. hereby referred to as HD FIRE warrants to the original purchaser of the fire protection products manufactured by HD FIRE and to any other person to whom such equipment is transferred, that such products will be free from defect in material and workmanship under normal use and care, for two (2) years from the date of shipment by HD FIRE. Products or Components supplied or used by HD FIRE, but manufactured by others, are warranted only to the extent of the manufacturer s warranty. No warranty is given for product or components which have been subject to misuse, improper installation, corrosion, unauthorized repair, alteration or un-maintained. HD FIRE shall not be responsible for system design errors or improper installation or inaccurate or incomplete information supplied by buyer or buyer s representatives. HD FIRE will repair or replace defective material free of charge, which is returned to our factory, transportation charge prepaid, provided after our inspection the material is found to have been defective at the time of initial shipment from our works. HD FIRE shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product including damages for injury to person, damages to property and penalties resulting from any products and components manufactured by HD FIRE. HD FIRE shall not be liable for any damages or labour charges or expense in making repair or adjustment to the product. HD FIRE shall not be liable for any damages or charges sustained in the adaptation or use of its engineering data & services. In no event shall HD Fire s product liability exceed an amount equal to the sale price. The foregoing warranty is exclusive and in lieu of all other warranties and representation whether expressed, implied, oral or written, including but not limited to, any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled. NOTICE : The equipment presented in this bulletin is to be installed in accordance with the latest publication standards of NFPA or other similar organisations and also with the provision of government codes or ordinances wherever applicable. The information provided by us are to the best of our knowledge and belief, and are general guidelines only. Site handling and installation control is beyond our reach. Hence we give no guarantee for result and take no liability for damages, loss or penalties whatsoever, resulting from our suggestion, information, recommendation or damages due to our product. Product development is a continuous programme of HD FIRE PROTECT PVT. LTD. and hence the right to modify any specification without prior notice is reserved with the company. HD FIRE PROTECT PVT. LTD. Protecting What Matters Most to You C-3/6, THE NANDANVAN IND. ESTATE, L.B.S. MARG, THANE , INDIA. PHONES : + (91) FAX : +(91) info@hdfire.com WEBSITE : OCTOBER, 2013 PAGE 1 OF 1 HD 208

8 FOAM CONCENTRATE BYPASS VALVE TECHNICAL DATA MODEL SIZE MAXIMUM SERVICE PRESSURE END CONNECTION FRICTION LOSS IN TERMS OF EQUIVALENT LENGTH OF PIPE (C-120) FACTORY HYDROSTATIC TEST PRESSURE FINISH ORDERING INFORMATION BV with Bronze material IS-318 / ASTM B62 BV-S with stainless steel material SS 316 (ASTM A 351-CF8M) 40 & 50NB (1.5 & 2 INCH) 14 Bar (200 PSI) Screwed Female BSPT (NPT Optional) 50NB Meters 40NB Meters 25 Bar (365 PSI) Red epoxy painted Specify 1) Size 2) End connection APPLICATION The foam concentrate bypass valve is used in the balance pressure foam proportioning pump skid system. The valve bypasses the controlled excess quantity of foam concentrate to concentrate storage tank. SPECIFICATION The valve is diaphragm operated and works on the simple differential pressure principle. The pressure sensing lines, one from ratio controller inlet for water pressure and another from the concentrate supply pressure above the metering orifice are connected to bypass valve. The bypass valve automatically adjusts the concentrate pressure corresponding to the water pressure. The bypass is provided with flush out valves. The pressure sensing hose is Teflon with stainless steel braided cover and it is permanently attached with swivel coupling. The two separate pressure gauges, one for the water and one for the foam concentrate are provided with valve trims. A duplex gauge is supplied as an optional item in lieu of two pressure gauges. Each valve is factory tested for its performance. INSPECTION AND MAINTENANCE A qualified and trained person must commission the system. After few initial successful tests an authorized person must be trained to perform inspection and testing of the system. Do not turn off the system or any valve to make repairs or test the system, without placing a roving Fire Patrol in the area protected by the system. The patrol should continue until the system is back in service. Also inform the local security guards and control alarm station, so as to avoid false alarm. It is recommended to carry out physical inspection of the system at least once a week. The inspection should verify that all the control valves are in proper position as per the system requirement and no damage has taken place to any component. The valve must be operated periodically and proper functioning must be verified. The test must be as per the procedure of system testing. The system must be flushed after each operation and free flow of water must be drained from the flush-out connection. The user is responsible for maintaining the valve in proper operating condition. OCTOBER, 2013 PAGE 1 OF 2 HD 186

9 FOAM CONCENTRATE BY-PASS VALVE FOAM PRESSURE GAUGE WATER PRESSURE GAUGE WATER FLUSHOUT VALVE FOAM FLUSHOUT VALVE RETURN LINE TO FOAM CONCENTRATE STORAGE TANK FOAM CONCENTRATE INLET FROM FOAM PUMP DRAIN PLUG FOAM CONCENTRATE SENSING LINE FROM RATIO CONTROLLER ABOVE CONCENTRATE METERING ORIFICE WATER PRESSURE SENSING LINE FROM INLET OF RATIO CONTROLLER LIMITED WARRANTY HD FIRE PROTECT PVT. LTD. hereby referred to as HD FIRE warrants to the original purchaser of the fire protection products manufactured by HD FIRE and to any other person to whom such equipment is transferred, that such products will be free from defect in material and workmanship under normal use and care, for two (2) years from the date of shipment by HD FIRE. Products or Components supplied or used by HD FIRE, but manufactured by others, are warranted only to the extent of the manufacturer s warranty. No warranty is given for product or components which have been subject to misuse, improper installation, corrosion, unauthorized repair, alteration or un-maintained. HD FIRE shall not be responsible for system design errors or improper installation or inaccurate or incomplete information supplied by buyer or buyer s representatives. HD FIRE will repair or replace defective material free of charge, which is returned to our factory, transportation charge prepaid, provided after our inspection the material is found to have been defective at the time of initial shipment from our works. HD FIRE shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product including damages for injury to person, damages to property and penalties resulting from any products and components manufactured by HD FIRE. HD FIRE shall not be liable for any damages or labour charges or expense in making repair or adjustment to the product. HD FIRE shall not be liable for any damages or charges sustained in the adaptation or use of its engineering data & services. In no event shall HD Fire s product liability exceed an amount equal to the sale price. The foregoing warranty is exclusive and in lieu of all other warranties and representation whether expressed, implied, oral or written, including but not limited to, any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled. NOTICE : The equipment presented in this bulletin is to be installed in accordance with the latest publication standards of NFPA or other similar organisations and also with the provision of government codes or ordinances wherever applicable. The information provided by us are to the best of our knowledge and belief, and are general guidelines only. Site handling and installation control is beyond our reach. Hence we give no guarantee for result and take no liability for damages, loss or penalties whatsoever, resulting from our suggestion, information, recommendation or damages due to our product. Product development is a continuous programme of HD FIRE PROTECT PVT. LTD. and hence the right to modify any specification without prior notice is reserved with the company. HD FIRE PROTECT PVT. LTD. Protecting What Matters Most to You C-3/6, THE NANDANVAN IND. ESTATE, L.B.S. MARG, THANE , INDIA. PHONES : + (91) FAX : +(91) info@hdfire.com WEBSITE : OCTOBER, 2013 PAGE 2 OF 2 HD 186

10 INLINE FOAM INDUCTOR TECHNICAL DATA MODEL IG - Bronze material IS - Stainless Steel material OPERATING 6.5 to 12 BAR PRESSURE ( PSI) FACTORY 25 BAR (365 PSI) HYDROSTATIC TEST PRESSURE INDUCTION 3 or 6% MAXIMUM BACK 65% of Inlet Pressure PRESSURE NOMINAL SIZE 65, 80, 100 &150 MM FINISH Red RAL 3000 ORDERING 1) Inductor Inlet Pressure INFORMATION 2) Foam solution flow required 3) Percentage of induction 4) Type of foam concentrate to be used 5) Maximum suction lift. 6) Flange connection DESCRIPTION Inline Foam Inductor is used to induct the foam liquid concentrate in water stream to supply proportioned solution of the liquid concentrate and water, to the foam producing equipment. The inductors are designed primarily for use in the fixed foam installation to provide a simple and reliable method of proportioning in constant flow applications. Each Inductor is designed for a pre-determined water pressure to give the correct proportioning at that pressure and discharge rate. The increase or decrease of the inlet pressure will result in an increase or decrease in the flow rate, which in turn will change the proportioning. SPECIFICATION Inductors are available in three different materials of construction, a wide range of flow from 75 to 3500 litres per minute at inlet pressure between 6.4 to 12 bar as shown in the graph. Each Inductor is accurately calibrated at the factory to match the flow, pressure and the induction requirement of the system. This enables to ensure and achieve the correct performance. SYSTEM DESIGN DETAILS The Inductor must be selected and installed in a hydraulically calculated system considering the limitation of permissible back pressure. The maximum back pressure allowed is expressed as 65% of pressure at the inlet of the inductor. The optimum performance of Inline Inductor is with pressure above 8 Bar (115 PSI). In the fixed foam system installation the inductor can be mounted above the concentrate storage tank. The maximum height of the Inductor suction pipe above the bottom of the storage tank to the inductor centre should not exceed 1.75 meters, with AFFF & 0.9 meter for AR-AFFF 3/3% foam concentrate. A minimum of 600 mm of unobstructed straight pipe line should be provided at the inlet and outlet of the inductor. The inductor must be installed in a system having minimum of 6.5 bar inlet pressure at inlet of inductor. The diameter of water supply pipe and water foam solution pipe should not be less than that of the diameter of the inductor. A shut-off valve provided in the induction line must be full bore on-off valve. The non-return valve if fitted in the foam induction pipe line, then it must be supplied or recommended by HD, so that the induction rate is properly calibrated in factory before supply. For best performance the inlet pressure at the inline inductor should be 6.8 bar or higher. APPLICATION Inline Foam Inductors are quite suitable for application utilizing single fixed discharge device. The Inline Inductors are not suitable for variable flow or pressure applications. The Inline Inductors are not suitable for Sprinkler system or system utilizing multiple small orifice discharge devices, which may result in increased back pressure due to blockage of discharge device. DECEMBER, 2013 PAGE 1 OF 6 HD 187

11 INSTALLATION AND MAINTENANCE Inductor must be supported firmly to prevent strain on the inductor itself. Qualified and trained person must commission the system. After few initial successful test, an authorized person must be trained to perform inspection and testing of the system. It is recommended to carry out physical inspection of the system regularly. The system must be fully tested at least once in a year or in accordance with applicable NFPA codes or in accordance to the standard of the organization having local jurisdiction. Do not turn off the system or any valve to make repair or test the system, without placing a roving Fire Patrol in the area covered by the system. The Patrol should continue until the system is back in service. Also inform the local security guard and control alarm station, so that a false alarm will not be signalled. SELECTION OF HD INLINE FOAM INDUCTOR SIZE Size of inductor Inductor K-Factor range 65NB 29.4 TO NB TO NB TO NB TO NOTES 1) It is recommended to select next higher size of inductor when the K-factor is very close to the higher range of model. 2) A pressuge gauge mounting socket at inlet and outlet of Inductor must be provided, which will help to analize the system during commissioning. The socket can be plugged in once the system has been commissioned successfully. 3) The maximum permissible back pressure is 65% of inlet pressure. The system designer should consider and design the system with 62% or less than back pressure as safe design. 4) Inductor must be adequately supported so that no strain is imposed on the inductor body. For selecting Inductor size, following formula to be used : Q = K P Q = Total solution flow rate in litres per minute. K = Inductor constant P = Inlet pressure in kg/sq.cm. Example : To find K-Factor Q = 200 LPM P = 8.0 kg/sq.cm. K = K = This K=70.71 falls within the range of inductor with 50 NB size. Hence 50 NB inductor should be selected. DECEMBER, 2013 PAGE 2 OF 6 HD 187

12 INLINE FOAM INDUCTOR B C F1 F2 A DIMENTIONS in millimeters (Approximate) INDUCTOR SIZE A B C FLANGE SIZE F1 / F2 65NB /4 BSP 65NB 80NB BSP 80NB 100NB /4 BSP 100NB 150NB /4 BSP 150NB MATERIAL OF CONSTRUCTION SR. DESCRIPTION MODEL NO. IG IS 1 HOUSING BRONZE IS:318, LTB-II SS 304 / 316 ASTM A351-CF8M 2 DIFFUSER BRONZE IS:318, LTB-II SS 304 / 316 ASTM A351-CF8M 3 NOZZLE BRONZE IS:318, LTB-II SS 304 / 316 ASTM A351-CF8M 4 ORIFICE SS 304 / 316 SS 304 / 316 ASTM A351-CF8M Standard supply is CF8, optional is CF8M DECEMBER, 2013 PAGE 3 OF 6 HD 187

13 PRESSURE VS FLOW-PERFORMANCE CHARACTERISTICS FLOW (LPM) INLET PRESSURE (KG./SQ.CM.) SIZE 65NB FLOW (LPM) INLET PRESSURE (KG./SQ.CM.) SIZE 80NB FLOW (LPM) INLET PRESSURE (KG./SQ.CM.) SIZE 100NB FLOW (LPM) INLET PRESSURE (KG./SQ.CM.) SIZE 150NB DECEMBER, 2013 PAGE 4 OF 6 HD 187

14 TYPICAL MOUNTING ARRANGEMENT OF INLINE FOAM INDUCTION SYSTEM WITH INDUCTOR MOUNTING ON TOP OF THE TANK NOTE : AUTOMATION OF THIS VALVE PERMITS THE ACTVATION OF THIS SYSTEM FROM ANY REMOTE SIGNALLING SOURCE. WATER SUPPLY FILL CONNECTION VENT EXPANSION DOME FOAM CONCENTRATE STORAGE TANK SIGHT GLASS DRAIN VALVE FOAM SOLUTION TO DISCHARGE DEVICE WITH INDUCTOR MOUNTING BELOW THE TANK FILL CONNECTION VENT EXPANSION DOME FOAM CONCENTRATE STORAGE TANK FOAM SOLUTION TO DISCHARGE DEVICE SIGHT GLASS DRAIN VALVE WATER SUPPLY INLINE INDUCTOR BALL VALVE SWING CHECK VALVE PIPE UNION NOTE : USE MINIMUM OF 600mm. STRAIGHT UNOBSTRUCTED PIPE AT INLET AND OUTLET OF EACH INLINE INDUCTOR. DECEMBER, 2013 PAGE 5 OF 6 HD 187

15 LIMITED WARRANTY HD FIRE PROTECT PVT. LTD. hereby referred to as HD FIRE warrants to the original purchaser of the fire protection products manufactured by HD FIRE and to any other person to whom such equipment is transferred, that such products will be free from defect in material and workmanship under normal use and care, for two (2) years from the date of shipment by HD FIRE. Products or Components supplied or used by HD FIRE, but manufactured by others, are warranted only to the extent of the manufacturer s warranty. No warranty is given for product or components which have been subject to misuse, improper installation, corrosion, unauthorized repair, alteration or un-maintained. HD FIRE shall not be responsible for system design errors or improper installation or inaccurate or incomplete information supplied by buyer or buyer s representatives. HD FIRE will repair or replace defective material free of charge, which is returned to our factory, transportation charge prepaid, provided after our inspection the material is found to have been defective at the time of initial shipment from our works. HD FIRE shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product including damages for injury to person, damages to property and penalties resulting from any products and components manufactured by HD FIRE. HD FIRE shall not be liable for any damages or labour charges or expense in making repair or adjustment to the product. HD FIRE shall not be liable for any damages or charges sustained in the adaptation or use of its engineering data & services. In no event shall HD Fire s product liability exceed an amount equal to the sale price. The foregoing warranty is exclusive and in lieu of all other warranties and representation whether expressed, implied, oral or written, including but not limited to, any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled. NOTICE : The equipment presented in this bulletin is to be installed in accordance with the latest publication standards of NFPA or other similar organisations and also with the provision of government codes or ordinances wherever applicable. The information provided by us are to the best of our knowledge and belief, and are general guidelines only. Site handling and installation control is beyond our reach. Hence we give no guarantee for result and take no liability for damages, loss or penalties whatsoever, resulting from our suggestion, information, recommendation or damages due to our product. Product development is a continuous programme of HD FIRE PROTECT PVT. LTD. and hence the right to modify any specification without prior notice is reserved with the company. HD FIRE PROTECT PVT. LTD. Protecting What Matters Most to You C-3/6, THE NANDANVAN IND. ESTATE, L.B.S. MARG, THANE , INDIA. PHONES : + (91) FAX : +(91) info@hdfire.com WEBSITE : DECEMBER, 2013 PAGE 6 OF 6 HD 187

16 INLINE BALANCE PRESSURE FOAM PROPORTIONER TECHNICAL DATA MODEL IB - Bronze construction IS 318 / ASTM B62 IBS - Stainless Steel (304) construction (ASTM A351-CF8) SIZE 80, 100 & 150 NB MAXIMUM SERVICE 14 Bar (200 PSI) PRESSURE MIMIMUM WORKING 3.0 Bar (44 PSI) PRESSURE MOUNTING ANSI B # Between the Flanges THREAD OPENING BSPT/NPT optional PRESSURE SENSING TEFLON tube with HOSE Stainless Steel braided cover TRIM CONNECTION Stainless Steel AND VARIOUS CONTROL VALVES FACTORY 25 Kg./ Sq.cm. (350 PSI) HYDROSTATIC TEST PRESSURE FINISH Epoxy red painted ORDERING Specify: INFORMATION a) Model Number b) Flow rate c) Percentage Induction d) Type of Foam Concentrate used APPLICATION The Inline Balance Pressure Foam Proportioners are used with positive displacement foam concentrate supply pump. The system controls accurately the flow of foam concentrate into the water stream over a wide range of flow rate and pressure. The Inline Balance Pressure Foam Proportioning System is used for simultaneous operation of the multiple foam injection even with different pressures between the two injection point with a single concentrate supply line. Various sizes of inline balance pressure proportioners can be combined to suit the flow requirement of each hazard area. SPECIFICATION Inline balance pressure proportioning system utilizes a single, positive displacement foam concentrate supply pump, an atmospheric foam concentrate storage tank, inline balance proportioner, and a foam concentrate regulating valve. The pressure regulating valve is mounted on foam concentrate return line to the foam concentrate storage tank. The valve regulates the foam concentrate supply pressure. The Inline balance pressure proportioner consists of a ratio controller, diaphragm operated pressure balancing valve, water and foam gauges, and pressure sensing hose of teflon tube with stainless steel braided cover, interconnecting trim fittings with various control and flush valves. The water inlet pressure and foam concentrate pressure at metering orifice is sensed by a diaphragm valve and it automatically balances the concentrate supply to provide accurately proportioned water foam solution over a wide range of flow conditions. A foam concentrate supply valve is also provided as an optional item. The system requires foam concentrate supply pressure of bar. higher than the water supply pressure. The Inline balance pressure proportioner is also provided with a manual balancing valve. INSPECTION AND MAINTENANCE A qualified and trained person must commission the system. After a few initial successful tests, an authorized person must be trained to perform the inspection and testing of the system. It is recommended to carry out physical inspection of the system at least once in a week. The inspection should verify that all the valves are in their proper position as per the system requirement and no damage has taken place to any component. The system where foam concentrate piping is maintained in charged condition, the provision should be made to flow foam through each Inline Balance Proportioner at least once in six weeks. The system should be fully tested at least once in a year or in accordance with applicable NFPA codes, or in accordance to the guidelines of the organization having local jurisdiction. JUNE, 2014 PAGE 1 OF 4 HD 189

17 RATIO CONTROLLER FLOW RANGE SIZE FLOW RANGE IN LPM AFFF 3% ARAFFF 3/3% to to to to to to INLINE BALANCE PRESSURE PROPORTIONER WITH MANUAL OVERRIDE FOAM GAUGE WATER GAUGE MANUAL OVERRIDE VALVE DIAPHRAGM BALANCE VALVE WATER FLUSH OUT VALVE FOAM CONCENTRATE SUPPLY VALVE ( 'E' ) FOAM CONCENTRATE INLET CONNECTION FOAM CONCENTRATE FLUSH OUT VALVE D FOAM SENSING LINE WATER SENSING LINE C DRAIN PLUG WATER INLET DIMENSIONS in mm (Approximate) B RATIO CONTROLLER WAFER STYLE A FOAM SOLUTION OUTLET MODEL Approximate Dimensions (in mm) A B C D E 80 NB RCW NB 100 NB RCW NB 150 NB RCW NB INLINE BALANCE PRESSURE PROPORTIONER WITHOUT MANUAL OVERRIDE WATER GAUGE FOAM GAUGE DIAPHRAGM BALANCE VALVE WATER FLUSH OUT VALVE FOAM CONCENTRATE SUPPLY VALVE FOAM SENSING LINE FOAM CONCENTRATE FLUSH OUT VALVE WATER SENSING LINE ( 'E' ) FOAM CONCENTRATE INLET CONNECTION DRAIN PLUG C D WATER INLET FOAM SOLUTION OUTLET B RATIO CONTROLLER WAFER STYLE DIMENSIONS in mm (Approximate) A Approximate Dimensions (in mm) MODEL A B C D E 80 NB RCW NB 100 NB RCW NB 150 NB RCW NB JUNE, 2014 PAGE 2 OF 4 HD 189

18 INLET PRESSURE VS FOAM SOLUTION FLOW INLET PRESSURE, PSI NB FOAM SOLUTION FLOW, LPM 180 INLET PRESSURE, PSI 150NB NB FOAM SOLUTION FLOW, LPM 160 INLET PRESSURE, PSI FOAM SOLUTION FLOW, LPM 18 FLOW VS PRESSURE LOSS Flow - GPM ( AXIS READING X 10) Friction Loss - PSI Friction Loss -KG/SQCM Flow - LPM (AXIS READING X 100) JUNE, 2014 PAGE 3 OF 4 HD 189

19 TYPICAL INLINE BALANCE PRESSURE FOAM PROPORTIONING SYSTEM CONCENTRATE RETURN LINE WATER SUPPLY CONCENTRATE RETURN VALVE FILL CONNECTION FOAM CONCENTRATE STORAGE TANK PUMP UNIT R PRESSURE REGULATING VALVE VENT VALVE EXPANSION DOME DRAIN VALVE CONCENTRATE SUPPLY VALVE FLUSH OUT FLUSH IN WATER PRESSURE GAUGE FOAM CONCENTRATE CONTROL VALVE FOAM SOLUTION DISCHARGE RATIO CONTROLLER CONCENTRATE PRESSURE GAUGE PUMP STARTER LIMITED WARRANTY HD FIRE PROTECT PVT. LTD. hereby referred to as HD FIRE warrants to the original purchaser of the fire protection products manufactured by HD FIRE and to any other person to whom such equipment is transferred, that such products will be free from defect in material and workmanship under normal use and care, for two (2) years from the date of shipment by HD FIRE. Products or Components supplied or used by HD FIRE, but manufactured by others, are warranted only to the extent of the manufacturer s warranty. No warranty is given for product or components which have been subject to misuse, improper installation, corrosion, unauthorized repair, alteration or un-maintained. HD FIRE shall not be responsible for system design errors or improper installation or inaccurate or incomplete information supplied by buyer or buyer s representatives. HD FIRE will repair or replace defective material free of charge, which is returned to our factory, transportation charge prepaid, provided after our inspection the material is found to have been defective at the time of initial shipment from our works. HD FIRE shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product including damages for injury to person, damages to property and penalties resulting from any products and components manufactured by HD FIRE. HD FIRE shall not be liable for any damages or labour charges or expense in making repair or adjustment to the product. HD FIRE shall not be liable for any damages or charges sustained in the adaptation or use of its engineering data & services. In no event shall HD Fire s product liability exceed an amount equal to the sale price. The foregoing warranty is exclusive and in lieu of all other warranties and representation whether expressed, implied, oral or written, including but not limited to, any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled. NOTICE : The equipment presented in this bulletin is to be installed in accordance with the latest publication standards of NFPA or other similar organisations and also with the provision of government codes or ordinances wherever applicable. The information provided by us are to the best of our knowledge and belief, and are general guidelines only. Site handling and installation control is beyond our reach. Hence we give no guarantee for result and take no liability for damages, loss or penalties whatsoever, resulting from our suggestion, information, recommendation or damages due to our product. Product development is a continuous programme of HD FIRE PROTECT PVT. LTD. and hence the right to modify any specification without prior notice is reserved with the company. HD FIRE PROTECT PVT. LTD. Protecting What Matters Most to You C-3/6, THE NANDANVAN IND. ESTATE, L.B.S. MARG, THANE , INDIA. PHONES : + (91) FAX : +(91) info@hdfire.com WEBSITE : JUNE, 2014 PAGE 4 OF 4 HD 189

20 SKID MOUNTED BALANCE PRESSURE FOAM PROPORTIONING SYSTEM APPLICATION Balance Pressure pump skid-proportioning system accurately controls the flow of foam concentrate in to the water stream. The system automatically controls the foam concentrate over a wide range of flow and pressure, without manual adjustment. The system is typically used in the fixed foam system and specialised mobile equipments to protect tank farm, offshore platform, air craft hanger, marine dock, loading rack and in many other applications and in all types of hazard. SPECIFICATION The basic system utilizes the principle of operation based on the use of a modified venturi device called Ratio Controller. As the water flows through a nozzle at the inlet of ratio controller, a low-pressure area is created between the inlet nozzle and a down stream section called diffuser. This low-pressure area causes foam concentrate to flow through a metering orifice at the concentrate inlet and into the low-pressure area. As the system demand varies, the flow through the ratio controller increase or decreases, which in turn varies the pressure at low pressure area of ratio controller, creating a corresponding pressure drop across the foam concentrate metering orifice. This corresponding change of pressure results in a foam concentrate flow, which is proportional to the water flow through the ratio controller. The pressure sensing line from the ratio controller inlet for water pressure, and from the concentrate supply side above the metering orifice are connected to a bypass valve. This valve automatically adjusts the concentrate pressure corresponding to the water pressure by re-circulating the concentrate in return line to the concentrate storage tank. Manually the pressure can also be balanced by using manual regulating globe valve to read equal pressure of the water gauge and the foam concentrate gauge (or through a duplex gauge). The system is available as a skid mounted unit, in different flow range, varying from 150 to LPM. Each skid consist of a positive displacement pump, a pump drive, an electric control, a bypass valve, a manual regulating valve, a ratio controller, interconnecting piping in stainless steel with various controlling valves, check valve, flush-in and flush-out valve. The system is also available for operation in auto mode. INSPECTION AND MAINTENANCE A qualified and trained person must commission the system. After few initial successful tests, an authorised person must be trained to perform the inspection and testing of the system. It is recommended to carry out physical inspection of the system at least once in a week. The inspector should verify that all the valves are in their proper position as per the system requirement and there is no damage to any component. Do not turn off the system or any valve to repair or test the system, without placing a roving Fire Patrol in the area covered by the system. The patrol should continue until the system is back in service. Also inform the local security guards and control alarm station, so that a false alarm will not be signalled. The system must be periodically checked for its normal operating condition. All the valves must be verified for its normal operating condition. The electrical controls must also be verified. The system must be operated periodically to verify its normal operating condition as per the instruction for testing provided with the equipment. The entire system must be fully tested at least once in a year in accordance with the applicable NFPA codes, or in accordance to the guidelines of the organisation having local jurisdiction. SEPTEMBER, 2014 PAGE 1 OF 2 HD 190

21 TYPICAL INSTALLATION OF BALANCE PRESSURE FOAM PROPORTIONING SYSTEM FILL CONNECTION VENT / BREATHER VALVE (OPTIONAL) EXPANSION DONE FOAM CONCENTRATE STORAGE TANK CONCENTRATE SUPPLY VALVE FLUSH IN DRAIN VALVE CONCENTRATE RETURN VALVE FLUSH OUT CONCENTRATE RETURN LINE MANUAL CONTROL VALVE BY-PASS VALVE PUMP UNIT MOTOR STARTER ~ WATER SUPPLY WATER PRESSURE SENSING LINE RATIO CONTROLLER CONCENTRATE PRESSURE SENSING LINE FOAM SOLUTION DISCHARGE FOAM SOLUTION DISCHARGE LIMITED WARRANTY HD FIRE PROTECT PVT. LTD. hereby referred to as HD FIRE warrants to the original purchaser of the fire protection products manufactured by HD FIRE and to any other person to whom such equipment is transferred, that such products will be free from defect in material and workmanship under normal use and care, for two (2) years from the date of shipment by HD FIRE. Products or Components supplied or used by HD FIRE, but manufactured by others, are warranted only to the extent of the manufacturer s warranty. No warranty is given for product or components which have been subject to misuse, improper installation, corrosion, unauthorized repair, alteration or un-maintained. HD FIRE shall not be responsible for system design errors or improper installation or inaccurate or incomplete information supplied by buyer or buyer s representatives. HD FIRE will repair or replace defective material free of charge, which is returned to our factory, transportation charge prepaid, provided after our inspection the material is found to have been defective at the time of initial shipment from our works. HD FIRE shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product including damages for injury to person, damages to property and penalties resulting from any products and components manufactured by HD FIRE. HD FIRE shall not be liable for any damages or labour charges or expense in making repair or adjustment to the product. HD FIRE shall not be liable for any damages or charges sustained in the adaptation or use of its engineering data & services. In no event shall HD Fire s product liability exceed an amount equal to the sale price. The foregoing warranty is exclusive and in lieu of all other warranties and representation whether expressed, implied, oral or written, including but not limited to, any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled. NOTICE : The equipment presented in this bulletin is to be installed in accordance with the latest publication standards of NFPA or other similar organisations and also with the provision of government codes or ordinances wherever applicable. The information provided by us are to the best of our knowledge and belief, and are general guidelines only. Site handling and installation control is beyond our reach. Hence we give no guarantee for result and take no liability for damages, loss or penalties whatsoever, resulting from our suggestion, information, recommendation or damages due to our product. Product development is a continuous programme of HD FIRE PROTECT PVT. LTD. and hence the right to modify any specification without prior notice is reserved with the company. HD FIRE PROTECT PVT. LTD. Protecting What Matters Most to You C-3/6, THE NANDANVAN IND. ESTATE, L.B.S. MARG, THANE , INDIA. PHONES : + (91) FAX : +(91) info@hdfire.com WEBSITE : SEPTEMBER, 2014 PAGE 2 OF 2 HD 190

22 FOAM CONCENTRATE CONTROL VALVE TECHNICAL DATA MODEL CV SIZE 25NB, 40NB & 50NB RATED PRESSURE 14 Kg./sq.cm. (200 PSI) END CONNECTION Flanged end to ANSI B 16.5 Class 150# PRESSURE SENSING Teflon tube with Stainless HOSE Steel braided cover TRIM CONNECTION Brass / Stainless Steel FACTORY 25 Kg./sq.cm. (365 PSI) HYDROTESTED FINISH RED RAL 3000 ORDERING Specify Model, Size INFORMATION of valve APPLICATION Foam concentrate control valve is designed for use in bladder tank foam system or inline balance pressure proportioning system. The valve opens automatically when water supply is established through the inlet pipe of ratio controller of bladder tank or in the inline balance pressure proportioning system. The valve opens at minimum of 2.1 Kg./sq.cm. (30 psi) water pressure. No electric power is required to operate the valve. SPECIFICATION The foam concentrate control valve utilizes water as the medium to open the valve. A manual override facility is provided to open the valve. In normal condition the valve remains in closed position. When, a minimum water pressure of 2.1 Kg./sq.cm. (30 psi) is established the valve opens and closing of the valve is manual. INSPECTION AND MAINTENANCE A qualified and trained person must commission the system. After few initial successful tests, an authorised person must be trained to perform the inspection and testing of the system at least once in a week. The inspection should verify that all the control valves are in their proper position as per the system requirement and no damage has taken place to any component. The foam concentrate control valve / system must be operated at least once in six weeks. The total system should be fully tested at least once in a year as per NFPA / TAC manual or in accordance to the guidelines of the organisation having local jurisdiction. 3 4 OPEN CLOSED WATER PRESSURE SENSER SUPPLY FROM INLET SIDE OF RATIO CONTROLLER FOAM CONCENTRATE INLET FOAM CONCENTRATE OUTLET SR NO. DESCRIPTION MATERIL SPECIFICATION 1 Valve Stainless Steel 2 Pipe Stainless Steel 3 Cylinder Stainless Steel 4 Hose Stainless Steel 5 Flange Stainless Steel SELECTION OF FOAM CONCENTRATE CONTROL VALVE HD Proportioner Foam Concentrate Control Valve Size 65 NB 25 NB 80 NB 40 NB 100 NB 40 NB 150 NB 50 NB OCTOBER, 2013 PAGE 1 OF 2 HD 194

23 FOAM CONCENTRATE WATER FOAM CONCENTRATE TYPICAL INSTALLATION OF FOAM CONCENTRATE CONTROL VALVE FOAM CONCENTRATE CONTROL VALVE SWING CHECK VALVE FOAM CONCENTRATE CONTROL VALVE TO SPRINKLER NETWORK WATER RATIO CONTROLLER BLADDER TANK DELUGE VALVE RATIO CONTROLLER FOAM SOLUTION OUTLET BLADDER TANK SPRINKLER ALARM ALARM VALVE WATER CONTROL VALVE WATER INLET WATER INLET LIMITED WARRANTY HD FIRE PROTECT PVT. LTD. hereby referred to as HD FIRE warrants to the original purchaser of the fire protection products manufactured by HD FIRE and to any other person to whom such equipment is transferred, that such products will be free from defect in material and workmanship under normal use and care, for two (2) years from the date of shipment by HD FIRE. Products or Components supplied or used by HD FIRE, but manufactured by others, are warranted only to the extent of the manufacturer s warranty. No warranty is given for product or components which have been subject to misuse, improper installation, corrosion, unauthorized repair, alteration or un-maintained. HD FIRE shall not be responsible for system design errors or improper installation or inaccurate or incomplete information supplied by buyer or buyer s representatives. HD FIRE will repair or replace defective material free of charge, which is returned to our factory, transportation charge prepaid, provided after our inspection the material is found to have been defective at the time of initial shipment from our works. HD FIRE shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product including damages for injury to person, damages to property and penalties resulting from any products and components manufactured by HD FIRE. HD FIRE shall not be liable for any damages or labour charges or expense in making repair or adjustment to the product. HD FIRE shall not be liable for any damages or charges sustained in the adaptation or use of its engineering data & services. In no event shall HD Fire s product liability exceed an amount equal to the sale price. The foregoing warranty is exclusive and in lieu of all other warranties and representation whether expressed, implied, oral or written, including but not limited to, any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled. NOTICE : The equipment presented in this bulletin is to be installed in accordance with the latest publication standards of NFPA or other similar organisations and also with the provision of government codes or ordinances wherever applicable. The information provided by us are to the best of our knowledge and belief, and are general guidelines only. Site handling and installation control is beyond our reach. Hence we give no guarantee for result and take no liability for damages, loss or penalties whatsoever, resulting from our suggestion, information, recommendation or damages due to our product. Product development is a continuous programme of HD FIRE PROTECT PVT. LTD. and hence the right to modify any specification without prior notice is reserved with the company. HD FIRE PROTECT PVT. LTD. Protecting What Matters Most to You C-3/6, THE NANDANVAN IND. ESTATE, L.B.S. MARG, THANE , INDIA. PHONES : + (91) FAX : +(91) info@hdfire.com WEBSITE : OCTOBER, 2013 PAGE 2 OF 2 HD 194

24 FOAM MAKER MODEL - FMA & FMA-S TECHNICAL DATA MODEL INLET SIZE WORKING PRESSURE FMA-50, FMA-65 - Carbon Steel Construction FMA-S 50, FMA-S 65 - Stainless Steel Construction 50, 65 NB Minimum 2.8 Kg/sq.cm. (40 PSI) Maximum 7 Kg/sq.cm. (100 PSI) FLANGE ANSI B 16.5 class 150# CONNECTION FINISH Red RAL 3000 WEIGHT 50 NB Kg (Approx.) 65 NB Kg APPROVAL UL Listed ORDERING INFORMATION APPLICATION Specify: a) Model and inlet size b) Inlet pressure c) Flow Solution flow required. d) Inlet Outlet flange e) Type of Foam Concentrate used Foam Maker is used for one of the most common applications of protecting tank seal in vertical liquid storage tank with internal floating roof with low expansion foam system. The application of aspirated foam is on the basis of the risk comprising the area in the annular ring between the rim of the floating roof and the tank shell. The Foam system design guidelines generally used are in accordance with NFPA11 standard. The Foam Makers are defined by NFPA 11 as Type II discharge outlets for delivering the low expansion aspirated foam to the seal. The Foam Makers are widely used with the Inline Foam Inductor, Balance Pressure Foam Proportioning system, Bladder Tank system and Foam tenders. SPECIFICATION Foam Maker is an air aspirating foam generator connected to the foam pourer to deliver the aspirated foam gently into the tank seal area. Foam maker covers wide range of foam solution rates from 75 to 550 litres per minute at 2.8 to 7 kg/sq.cm. inlet pressure. The orifice is field replaceable in the event of change in design parameters. The foam is produced by introducing air into the foam solution stream. The inlet of foam maker is designed to create venture jet which draws air into the foam solution stream. LISTED 4UT3 The air is drawn into the foam solution through holes located on the foam maker covered with stainless steel screen to exclude nesting birds and insects. The aerated foam is directed into the pourer for the gentle application of the expanded foam. The pourers are available in different models. TESTING AND MAINTENANCE Qualified and trained person must commission the system. After few initial successful tests, an authorized person must be trained to perform inspection and testing of the system. It is recommended to carry out physical inspection of the system regularly. The system must be fully tested at least once in a year or in accordance to standards of the organization having local jurisdiction. Do not turn off the system or any valve to make repair or test the system, without placing a roving Fire Patrol in the area covered by the system. The Patrol should continue until the system is put back in service. Also inform the local security guard and control alarm station, so as to avoid false alarm. Each system is to be flushed properly. To test the Foam Maker without discharging the foam into the tank seal area, the foam maker is to be rotated 180o away from the wind shield. The air screen is to be inspected periodically for obstruction of air inlet holes. If any obstruction is noticed, remove the same and flush if necessary. The foam maker outlet and pourer, if exposed to atmospheric condition, should be periodically inspected for nest and other obstructions. Any obstruction if noticed must be removed and flushed to clear the discharge path. NOTE: A PROVISION IS TO BE MADE FOR PRESSURE GAUGE MOUNTING AT INLET OF FOAM MAKER, WHICH MAY BE PLUGGED AFTER SUCCESSFUL COMMISSIONING OF THE SYSTEM. THIS WILL HELP TO ANALYSE THE SYSTEM WHILE COMMISSIONING. DECEMBER, 2013 PAGE 1 OF 4 HD 255

25 Selection of HD Foam Maker: FOAM MAKER SIZE K - FACTOR 50 NB 44.8 TO NB 89.6 TO To select the size of the Foam Maker use the following formula: Q = K P Where, Example: To find K factor: Q = 150LPM P = 3.5Kg/sq.cm. K = = The K-Factor falls within the range of the Foam Maker having 50NB size. Hence 50NB size Foam Maker to be selected. The Foam Maker can also be selected from the graph. Q = Total solution flow in litres per minute. K = Constant for Foam Chamber P = Inlet pressure in kg/sq.cm. FOAM MAKER 5 F2 4 'A' F1 DIMENSIONS OF FOAM MAKER in millimeter (Approximate) FOAM MAKER SIZE INLET (F1) OUTLET (F2) 50NB 50NB 80NB NB 65NB 100NB 400 A PART LIST ITEM MATERIAL SPECIFICATION DESCRIPTION NO. FMA FMA-S 1 ORIFICE ASSEMBLY STAINLESS STEEL STAINLESS STEEL 2 INLET FLANGE STEEL STAINLESS STEEL 3 STRAINER ASSEMBLY STAINLESS STEEL STAINLESS STEEL 4 FOAM MAKING CHAMBER STEEL PIPE SS PIPE 5 OUTLET FLANGE STEEL STAINLESS STEEL DECEMBER, 2013 PAGE 2 OF 4 HD 255

26 TYPICAL INSTALLATION OF FOAM MAKER WITH POURER 400 (MAX) PIPING (BY OTHERS) WINDSHIELD (BY OTHERS) NOZZLE (BY OTHERS) 300 APPROX. FOAM MAKER FOAM POURER MODEL-FP55 FOAM DAM * * PIPING (BY OTHERS) NOTE: 1. Above dimensions are general guidelines only. The system designer can adopt the dimensions as per NFPA/TAC/OISD or as per the governing rules & ordinance having local jurisdiction. 2. See the UL listing details for foam or contact HD FIRE. 3. Foam Pourer Model - FP55 is standard supply in carbon steel material and optional in stainless steel. DECEMBER, 2013 PAGE 3 OF 4 HD 255

27 PRESSURE VS FLOW PERFORMANCE CHARACTERISTIC FOAM SOLUTION FLOW (LPM) FOAM SOLUTION FLOW (LPM) INLET PRESSURE (KG/SQ.CM) FMA 50 & FMA-S INLET PRESSURE (KG/SQ.CM) FMA 65 & FMA-S 65 LIMITED WARRANTY HD FIRE PROTECT PVT. LTD. hereby referred to as HD FIRE warrants to the original purchaser of the fire protection products manufactured by HD FIRE and to any other person to whom such equipment is transferred, that such products will be free from defect in material and workmanship under normal use and care, for two (2) years from the date of shipment by HD FIRE. Products or Components supplied or used by HD FIRE, but manufactured by others, are warranted only to the extent of the manufacturer s warranty. No warranty is given for product or components which have been subject to misuse, improper installation, corrosion, unauthorized repair, alteration or un-maintained. HD FIRE shall not be responsible for system design errors or improper installation or inaccurate or incomplete information supplied by buyer or buyer s representatives. HD FIRE will repair or replace defective material free of charge, which is returned to our factory, transportation charge prepaid, provided after our inspection the material is found to have been defective at the time of initial shipment from our works. HD FIRE shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product including damages for injury to person, damages to property and penalties resulting from any products and components manufactured by HD FIRE. HD FIRE shall not be liable for any damages or labour charges or expense in making repair or adjustment to the product. HD FIRE shall not be liable for any damages or charges sustained in the adaptation or use of its engineering data & services. In no event shall HD Fire s product liability exceed an amount equal to the sale price. The foregoing warranty is exclusive and in lieu of all other warranties and representation whether expressed, implied, oral or written, including but not limited to, any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled. NOTICE : The equipment presented in this bulletin is to be installed in accordance with the latest publication standards of NFPA or other similar organisations and also with the provision of government codes or ordinances wherever applicable. The information provided by us are to the best of our knowledge and belief, and are general guidelines only. Site handling and installation control is beyond our reach. Hence we give no guarantee for result and take no liability for damages, loss or penalties whatsoever, resulting from our suggestion, information, recommendation or damages due to our product. Product development is a continuous programme of HD FIRE PROTECT PVT. LTD. and hence the right to modify any specification without prior notice is reserved with the company. HD FIRE PROTECT PVT. LTD. Protecting What Matters Most to You C-3/6, THE NANDANVAN IND. ESTATE, L.B.S. MARG, THANE , INDIA. PHONES : + (91) FAX : +(91) info@hdfire.com WEBSITE : DECEMBER, 2013 PAGE 4 OF 4 HD 255

28 RATIO CONTROLLER MODEL RCW-B & RCW-S TECHNICAL DATA MODEL SIZE MAX. SERVICE PRESSURE FACTORY HYDRO TEST PRESSURE MOUNTING APPROVAL FINISH ORDERING INFORMATION DESCRIPTION RCW-B Bronze RCW-S Stainless Steel 65, 80,100 &150 NB 14 Bar (200 PSI) 25 Kg./Sq.cm. (350 PSI) Between the flanges ANSI B # UL Listed with AFFF3% and with HD Bladder tank, with 12 bar maximum pressure Red RAL 3000 or Natural Finish Specify a) Model & Size b) Minimum and Maximum Pressure and flow rate c) Induction Percentage d) Type of Foam Concentrate used Ratio Controller is used for proportioning the foam concentrate into the water supply with a wide range of flow and pressure. The Ratio Controller is also used with Bladder Proportioning System, Inline Balance Proportioning System and Skid mounted pump balance proportioning system. SPECIFICATION The Ratio Controller works on venturi principle. As the water flow passes through nozzle at the inlet of ratio controller, a low-pressure area is created between inlet nozzle and the down stream section called diffuser. This low-pressure area causes the foam concentrate to flow through a metering orifice at the concentrate inlet and into the low-pressure area. As the system demand varies, the water jet through Ratio Controller increases or decreases, which in turn varies the pressure at the low-pressure area of the Ratio Controller. This affects the corresponding pressure across the foam concentrate-metering orifice. The system requires same pressure of water and concentrate in order to balance the proportioning system. INSTALLATION Ratio Controller Model RCW is wafer style to be mounted in SCH40 pipe between two flanges. NOTE U L LISTED EX ) A minimum of five pipe diameter of straight unobstructed pipe is required at upstream and down stream of each ratio controller. 2) Ratio Controller shall be installed between two ANSI 150# flanges with raised face or flat face. The gasket-stud, flanges shall be provided by the installer. 3) Provision shall be made in piping for removal of Ratio Controller. 4) The pipes on upstream & downstream side of the Ratio Controller must be adequately supported and no strain shall be imposed on Ratio Controller. 5) The Ratio Controller flow range given is with AFFF 3% foam concentrate. Consult HD Engineering Department for other foam concentrate types. 6) Ratio controller is UL Listed with HD Bladder Tank, refer UL Listing data for more information. 7) Ratio Controller is UL Listed for 2.1 to 12 bar pressure. OCTOBER, 2013 PAGE 1 OF 4 HD 263

29 RATIO CONTROLLER 'F' -Foam Concentrate Inlet Connector with orifice Gasket by installer 'D' 150# ANSI Bolted Flanges by installer Stud with bolt by installer Sch. 40 Piping by installer WATER WATER FOAM INLET Ø'C' SOLUTION OUTLET 1/4" FBSPT/FNPT Water Sensing Port Plugged 'A' 'B' Ø'E' RATIO CONTROLLER - WAFER STYLE DIMENSION CHART Model Approximate Dimensions (in mm) A B Ø C D Ø E F 6 RCW Ø M20 x 230 LONG 2 BSP (F)/NPT (F) 4 RCW Ø M16 x 220 LONG 1-1/2 BSP (F)/NPT (F) 3 RCW Ø M16 x 200 LONG 1-1/2 BSP (F)/NPT (F) 2-1/2 RCW Ø M16 x 170 LONG 1 BSP (F)/NPT (F) RATIO CONTROLLER FLOW RANGE SIZE FLOW RANGE IN LPM AFFF3% ARAFFF3/3% 65 NB (2.5 ) 100 to to NB (3 ) 260 to to NB (4 ) 650 to to NB (6 ) 1200 to to OCTOBER, 2013 PAGE 2 OF 4 HD 263

30 INLET PRESSURE VS FOAM SOLUTION FLOW NB NB INLET PRESSURE, PSI INLET PRESSURE, PSI FOAM SOLUTION FLOW, LPM FOAM SOLUTION FLOW, LPM NB NB INLET PRESSURE, PSI INLET PRESSURE, PSI FOAM SOLUTION FLOW, LPM FOAM SOLUTION FLOW, LPM NOTE: Refer Table I for flow limtation for AR-AFFF 3/3% foam concentrate. FLOW VS PRESSURE LOSS 18 Flow - GPM ( AXIS READING X 10) Friction Loss - PSI / Friction Loss -KG/SQCM Flow - LPM (AXIS READING X 100) OCTOBER, 2013 PAGE 3 OF 4 HD 263

31 LIMITED WARRANTY HD FIRE PROTECT PVT. LTD. hereby referred to as HD FIRE warrants to the original purchaser of the fire protection products manufactured by HD FIRE and to any other person to whom such equipment is transferred, that such products will be free from defect in material and workmanship under normal use and care, for two (2) years from the date of shipment by HD FIRE. Products or Components supplied or used by HD FIRE, but manufactured by others, are warranted only to the extent of the manufacturer s warranty. No warranty is given for product or components which have been subject to misuse, improper installation, corrosion, unauthorized repair, alteration or un-maintained. HD FIRE shall not be responsible for system design errors or improper installation or inaccurate or incomplete information supplied by buyer or buyer s representatives. HD FIRE will repair or replace defective material free of charge, which is returned to our factory, transportation charge prepaid, provided after our inspection the material is found to have been defective at the time of initial shipment from our works. HD FIRE shall not be liable for any incidental or consequential loss, damage or expense arising directly or indirectly from the use of the product including damages for injury to person, damages to property and penalties resulting from any products and components manufactured by HD FIRE. HD FIRE shall not be liable for any damages or labour charges or expense in making repair or adjustment to the product. HD FIRE shall not be liable for any damages or charges sustained in the adaptation or use of its engineering data & services. In no event shall HD Fire s product liability exceed an amount equal to the sale price. The foregoing warranty is exclusive and in lieu of all other warranties and representation whether expressed, implied, oral or written, including but not limited to, any implied warranties or merchantability or fitness for a particular purpose. All such other warranties and representations are hereby cancelled. NOTICE : The equipment presented in this bulletin is to be installed in accordance with the latest publication standards of NFPA or other similar organisations and also with the provision of government codes or ordinances wherever applicable. The information provided by us are to the best of our knowledge and belief, and are general guidelines only. Site handling and installation control is beyond our reach. Hence we give no guarantee for result and take no liability for damages, loss or penalties whatsoever, resulting from our suggestion, information, recommendation or damages due to our product. Product development is a continuous programme of HD FIRE PROTECT PVT. LTD. and hence the right to modify any specification without prior notice is reserved with the company. HD FIRE PROTECT PVT. LTD. Protecting What Matters Most to You C-3/6, THE NANDANVAN IND. ESTATE, L.B.S. MARG, THANE , INDIA. PHONES : + (91) FAX : +(91) info@hdfire.com WEBSITE : OCTOBER, 2013 PAGE 4 OF 4 HD 263

32 RIM SEAL FOAM POURER MODEL - RPA & RPA-S TECHNICAL DATA MODEL RPA 65 Carbon Steel RPA-S 65 Stainless Steel SIZE 65 NB INLET WORKING Min 2.8 Kg/cm 2 (40 PSI) PRESSURE Max 7 Kg/cm 2 (100 PSI) FLANGE CONNECTION ANSI B16.5 class 150# FINISH Red RAL 3000 APPROVAL UL Listed ORDERING INFORMATION APPLICATION a) Model b) Flow & Pressure at inlet of each Foam Pourer c) Foam concentrate used d) Tank number / Tag number HD Rim Seal Foam Pourer RPA consists mainly of Foam Maker, a windshield and an integral deflector. The RPA is designed to deliver fully aspirated foam directly to the annular seal area of open top floating roof tank. The Rim Seal Foam Pourer is used for one of the most common applications of protecting tank seal in vertical liquid storage tank with internal floating roof with low expansion foam system. The application of aspirated foam is on the basis of the risk comprising the area in the annular ring between the rim of the floating roof and the tank shell. The Foam system design guidelines generally used are in accordance with NFPA 11 standard. Rim Seal Foam Pourers are defined by NFPA 11 as Type II discharge outlets for delivering the low expansion aspirated foam to the seal. The Rim Seal Foam Pourers are widely used with Inline Foam Inductor, Balance Pressure Foam Proportioning System, Bladder Tank system or Foam tenders. SPECIFICATION The Rim Seal Foam Pourer is an air aspirating foam generator connected to the foam pourer to deliver the aspirated foam gently into the tank seal area. The rim seal foam pourer covers a wide range of foam solution rates from 50 to 550 liters per minute at 2.8 to 7 kg/ sq.cm inlet pressure. Each rim seal foam pourer is supplied with an orifice plate, designed for the required flow at inlet pressure. The orifice is field replaceable in the event of change in design parameters. The foam is produced by introducing air into the foam solution stream. The inlet of foam maker is designed to create venturi jet which draws air into the foam solution stream. The air is drawn into the foam solution through holes located on the foam maker covered with stainless steel screen to exclude nesting birds and insects. SYSTEM DESIGN REQUIREMENT LISTED 4UT3 For essential requirement of appropriately designed foam pouring system for storage tanks refer NFPA- 11/ OISD/ TAC/ Governmental codes or ordinances wherever applicable. TESTING & MAINTENANCE Qualified and trained person must commission the system. After few initial successful tests, an authorized person must be trained to perform inspection and testing of the system. It is recommended to carry out physical inspection of the system regularly. The system must be fully tested at least once in a year or in accordance to the standards of the organization having local jurisdiction. Do not turn off the system or any valve to make repair or test the system, without placing a roving Fire Patrol in the area covered by the system. The Patrol should continue until the system is put back in service. Also inform the local security guard and control alarm station, so as to avoid false alarm. Each system is to be flushed properly. To test the RPA without discharging the foam into the tank seal area, the RPA is to be rotated 180 away from the wind shield. The air screen is to be inspected periodically for the obstruction of air inlet holes. If any obstruction is noticed, remove the same and flush, if necessary. The RPA outlet and pourer, if exposed to atmospheric condition, should be periodically inspected for nest and other obstructions. The obstruction, if noticed, must be removed and flushed to clear the discharge path. OCTOBER, 2013 PAGE 1 OF 3 HD 253