Installation Instructions. CAR COMING Pedestrian Alert Safety Signs (PASS)
|
|
- Karin Richard
- 5 years ago
- Views:
Transcription
1 Installation Instructions CAR COMING Pedestrian Alert Safety Signs (PASS) Pedestrian Alert Safety System (PASS)
2 Quick Guide Please read the entire guide or watch our instructional videos if you are new to the CAR COMING System. 1) Lay the sign on its back on a non-abrasive surface 2) Remove the two fastening screws from the bottom of the enclosure using a 5/32 Allen wrench 3) Slide the Front Cover of the enclosure down and remove from the Back Mounting Plate. Place the Front Cover on a non-abrasive surface 4) Remove the top and bottom fastening screws that connect the Internal enclosure to the back mounting plate 5) Hinge the Internal enclosure to an open position 6) Remove the two additional screws that connect the Internal enclosure to the Back Mounting Plate 7) Remove the Internal enclosure and place on a non-abrasive surface 8) Mount the Back Mounting Plate to the wall no less than 76 from the ground from the bottom of the Back Mounting Plate. Use fasteners specified for the wall surface and with a 50lbs strength. 9) Turn off all electrical power that will be provided to the sign 10) Bring the Power cabling (120VAC or 12VDC) through the back of the plate 11) Bring the Trigger cable through the back of the plate 12) Mount the Internal enclosure with the two screws to the Back Mounting plate, but leave hinged open 13) Terminate the Trigger cable to Input 1 Dry if the output contact is Normally Open, or to Input 12/24 if the Output is a 12-24V output 14) Connect 120VAC to the internal transformer, or if you are providing 12VDC to the sign then terminate 12VDC to Power IN terminal 15) Using a small screwdriver turn the Dial for PLAY to the 9 o clock position 16) Using a small screwdriver turn the Dial for DELAY to the 0 position 17) Using a small screwdriver turn the Dial for Volume to the 12 o clock position 18) Apply power to the sign and ensure the Power LED lights up 19) Press the Test Input 1 button and adjust the Volume with a small screwdriver to the desired volume 20) Press the Test 1 button and adjust the PLAY for the desired activation timer 21) Press the Test 1 button and adjust the DELAY for the desired delay before activation timer 22) Ensure all LED Modules are lighting up 23) Once you are satisfied with performance of the sign, hinge the Internal enclosure closed and fasten it closed 24) Slide the Front Cover up and screw in the two Allen head screws
3 Types of Installation The CAR COMING Pedestrian Alert Safety System (PASS) can be installed in a variety of configurations. The system is versatile and can be triggered from any type of vehicle detection device, or multiple vehicle detection devices. The sign can also be triggered from non-obvious devices such as a wireless remote from a Bus Driver, or a Cash Register drawer open relay, or an access control system card read output. The sign is triggered by a dry normally open output and can operate on 12VDC or 120VAC. In addition, If you have questions on the best approach to an installation, or call us! We are happy to help you design your installation wiring. Common System Triggers Barrier Gate is Open output Barrier Safety Loop Activated output Parking Ticket Exit station Open Gate output Access control Open Door/Gate output Vehicle loop detector output Roll-up door Open output Photobeam detector output Vehicle motion detector output
4 Wiring Requirements The CAR COMING System was designed for easy wiring design and installation allowing low-voltage technicians (and non-technicians) installation without a line-voltage electrician. Easy Single Cable Installation (Single Barrier, Roll-up Door, Swing/Slide Gate) This is the most common installation and only requires a single cable between a barrier gate and the sign for Power and Activation Signal. Recommended cable is an 18 AWG / 4 Conductor. 120VAC power will be supplied from the Barrier Gate electrical circuit to the CAR COMING transformer (supplied) to provide 12VDC back to the sign for operation. If barriers arms are raised on a time schedule (ie overnight, special events) then use the Safety Loop Activation Output. The Safety Loop is the vehicle detection loop located under the barrier arm. The waterproof transformer inside the CAR COMING system can be removed and re-located inside the barrier. This avoids the need to bring 120VAC to the sign. This could be replicated in a ROLL-UP DOOR, SLIDING GATE, or SWING GATE. Brand Output Magnetic Auto Microdrive Output 6 programmed GATE OPENING (not Open) Skidata Output from 582 Column onboard relay programmed for Open Barrier 3M (FAPD) Output 8 Safety Loop Activated HUB Zeag LX Station Output 1 (Open Barrier) to Input 24VDC on PASS Controller If you have a barrier you have installed and would like to add to the list please us the information to jeff.terrozas@passsigns.com
5 Easy Single Cable Installation (Multiple Barriers, Roll-up Doors, Swing/Slide Gates) This is the most common installation and only requires a single cable between a barrier gate and the sign for Power and Activation Signal. Recommended cable is an 18 AWG / 4 Conductor. Then only 2 Conductors will need to be used between devices. 120VAC power will be supplied from the Barrier Gate electrical circuit to the CAR COMING transformer (supplied) to provide 12VDC back to the sign for operation. If barriers arms are raised on a time schedule (ie overnight, special events) then use the Safety Loop Activation Output. The Safety Loop is the vehicle detection loop located under the barrier arm. The waterproof transformer inside the CAR COMING system can be removed and re-located inside the barrier. This avoids the need to bring 120VAC to the sign. This could be replicated with multiple ROLL-UP DOORS, SLIDING GATES, or SWING GATES. Common Barriers Output (If you need help with a design, contact us and we can help you) Brand Output Magnetic Auto Microdrive Output 6 programmed GATE OPENING (not Open) Skidata Output from 582 Column onboard relay programmed for Open Barrier 3M (FAPD) Output 8 Safety Loop Activated HUB Zeag LX Station Output 1 (Open Barrier) to Input 24VDC on PASS Controller If you have a barrier you have installed and would like to add to the list please us the information to jeff.terrozas@passsigns.com
6 Motion Detector or Photobeams To detect vehicles without the use of barriers or vehicle loop detection, a motion detector(s) or photobeam(s) can be used. 120VAC or 12VDC power can be supplied to the CAR COMING system. The 12VDC power on the PASS Controller board will supply the power needed for the devices. PROS and CONS of using Photobeams Pros: A photobeam can be projected across multiple lanes of traffic to detect vehicles. Cons: Pedestrians can trigger photobeams and motion detectors creating nuisance alerts in high foot traffic areas.
7 Terminations: See the PSC-1 or PSC-2 Controller Guide for terminations. Located at passsigns.com/documentation Directional Logic Detection The waterproof transformer inside the CAR COMING system can be removed and re-located inside the barrier. This avoids the need to bring 120VAC to the sign. This could be replicated in a multiple ROLL-UP DOORS, SLIDING GATES, or SWING GATES. Common Barriers Output (If you need help with a design, contact us and we can help you)
8 Electrical Requirements Power Requirements: 120VAC 1 Amp OR 12VDC 5 Amps Trigger Input Normally Open Dry Contact 12VDC Output 24VDC Output Wiring Required for Installation Typical Wiring Installation (120VAC) from a Parking Gate Opening the Unit CAUTION DO NOT OPEN THE UNIT WHILE RAINING OR SNOWING. (1) Gently lay the unit on its back on a non-abrasive surface. Using a 5/32 allen wrench remove the two screws from the bottom of the unit. (2) Pull the front cover and slide down the sign s length and remove. If the front is difficult to pull off, use a flat screwdriver and gently pry at the bottom of the unit between the Front Cover and the Rear Plate. Opening the Interior Panel (1) Unscrew the bottom and top interior panel screws and hinge open the Interior Panel (2) If you are installing the sign, remove the two additional screws of the interior panel. This will make the installation of the Rear Plate much easier during installation. Mounting the Rear Plate Use the proper hardware dependent on the surface the sign is mounted to
Exit Stopper. STI-6400 Series
Exit Stopper STI-6400 Series Features Alarm helps prevent unauthorized exits/entries through doors. Easy to install. Select volume, alarm duration and delay settings. May be mounted on top, right, left
More informationABLOY DA460 SWING DOOR OPERATOR. Installation and commissioning manual
ABLOY DA460 SWING DOOR OPERATOR Installation and commissioning manual APPROVALS / STANDARDS 73/23/EEC (Low Voltage directive) 93/68/EEC (Low Voltage directive) 89/336/EEC (EMC directive) Statement of fire
More informationExit Stopper. STI-6400 Series
Exit Stopper STI-6400 Series Features Alarm helps prevent unauthorized exits/entries through doors. Easy to install. Select volume, duration and immediate or 15 second delay for arming and trip. May be
More informationACSI AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1089, REV. F
II 1400-2 ACSI 1406-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1089, REV. F INSTALLATION Transformer Model BE31763001 by Basler Electric, Transformer Model 2010028 by Galaxy
More informationAddendum for STI-6406 with Dual Access Control
Addendum for STI-6406 with Dual Access Control Description: This system contains a STI-6400 with a DPDT key switch to be mounted on one side of a door or wall; and a similar looking housing, also with
More informationMAX ARM. Heavy Duty Linear Actuator for Residential / Commercial use. Super quiet Solar ready Large diameter stainless steel output shaft
MAX ARM Heavy Duty Linear Actuator for Residential / Commercial use Super quiet Solar ready Large diameter stainless steel output shaft MAX AC control box DSP Control 2 Years Warranty or 100,000 Cycles
More informationCARD ACCESS CONTROL SYSTEM
SECTION 13851 CARD ACCESS CONTROL SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Section Includes: A complete, operable, tested, integrated proximity access control system, to operate on a proximity principle where
More informationSP-1000X. Panic Device Power Controller Installation Guide. Rev
TM SP-1000X Panic Device Power Controller Installation Guide Rev. 120213 Overview: SP-1000X will operate up to two (2) 24VDC panic hardware devices simultaneously. It is designed to handle the high current
More informationMANUAL RESET ALARM RELEASE
Fire Door Release MODEL AR-D MANUAL RESET ALARM RELEASE INSTRUCTION MANUAL AR-D GENERAL INFORMATION 1. Review all installation instructions, procedures, cautions and warnings contained within this manual
More informationDS160/161 Request To Exit PIR sensors Installation Instructions
DS160/161 Request To Exit PIR sensors Installation Instructions 1.0 Description The DS160/161 is a passive-infrared (PIR) detector designed for request to exit (REX) interior applications. It is UL Listed
More informationRPSMLR2 RPSMLR2BB. Panic Device Power Controller Installation Guide LISTED. Rev
RPSMLR2 RPSMLR2BB Panic Device Power Controller Installation Guide LISTED Rev. 102715 Overview: RPSMLR2BB, RPSMLR2 will operate up to two (2) 24VDC panic hardware devices simultaneously. It is designed
More informationBLG77 Rising Fenced Barrier
BLG77 Rising Fenced Barrier 1/8 ENGINEERING SPECIFICATIONS BLG77 Rising Barrier PART I GENERAL SECTION 08 34 56 Security Gates SECTION 11 12 33 Parking Gates SECTION 28 13 00 Access Control SECTION 34
More informationDS160/DS161 Request To Exit PIR sensors Installation Instructions
DS160/DS161 Request To Exit PIR sensors Installation Instructions 1.0 Description The DS160 is a Passive Infrared Detector (PIR) which is UL Listed as an Access Control Device under the UL 294 Standard.
More informationRDM LOCK G Series Electromagnetic Lock. Listings. Standard Features. Ordering Information:
RDM LOCK G-1 1400 Series Electromagnetic Lock The patented 1400 Series Electromagnetic Lock is universal for all types of applications, including outdoor use. The innovative design will reduce installation
More information5900 SERIES Low Energy Power Operator
Low Energy Power Operator introduction The Norton 5900 Series is a full-featured, extremely quiet, low energy door operator designed for moderate to high traffic doors. This cost-effective operator is
More informationOperating Instructions
CS101 CarSense Vehicle Motion Detector Operating Instructions CAUTIONS AND WARNINGS Never use the CS101 as a safety reversing or presence detection system. The CS101 requires that a vehicle be moving for
More informationWARNING. Installation Tip: Try out this unit before installing onto a fire door system. Test and learn the release INTRODUCTION
WARNING 1. CAUTION: Review all installation instructions, procedures, cautions and warnings contained within this manual prior to installing and/or servicing this product. As with all releasing device
More informationEngineering Specifications
BL229 Rising Barrier NAM-BL229-ES-EN-A 1/8g ENGINEERING SPECIFICATIONS BL229 Rising Barrier PART I GENERAL SECTION 08 34 56 Security Gates SECTION 11 12 33 Parking Gates SECTION 28 13 00 Access Control
More informationRELEASE DEVICES RELEASE DEVICE-WPS MODELS A/B INSTALLATION MANUAL U.L. LISTED CANADIAN LISTED CSFM: :100 GENERAL DESCRIPTION:
RELEASE DEVICES MADE IN THE U.S.A. RELEASE DEVICE-WPS MODELS A/B INSTALLATION MANUAL U.L. LISTED CANADIAN LISTED CSFM: 7300-1418:100 GENERAL DESCRIPTION: S/N: The "WPS" World Power Series, Time Delay Release
More informationInstallation Instructions
Installation Instructions KFN 9855 ide en - CA Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations
More informationPOWER TRANSFERS ACCESSORIES EAC. Manufacturer Product Product No. Product Description Item No.
POWER TRANSFERS 47 Keedex Cord K-DLA K-DLB Keedex 18 Flexible Cord; Product No. K-DLA; 1/4 flexible conduit; use door loops when you need to transfer electrical current from the door frame to the door;
More informationFirefly II Multi Voltage RELEASE DEVICES. Firefly II & IIB-MV INSTALLATION MANUAL
Firefly II Multi Voltage RELEASE DEVICES Firefly II & IIB-MV INSTALLATION MANUAL GENERAL DESCRIPTION: S/N The The Cookson Company Firefly II-MV time delay release devices are designed for use on rolling
More informationInstallation Instructions
Request-to-Exit Dual Technology Motion Sensor 1048889B November 2005 Copyright 2005, GE Security Inc. Introduction This is the GE Request-to-Exit Dual Technology Motion Sensor for models -W, -B, and -G.
More informationMANUAL RESET ALARM RELEASE BOX
MANUAL RESET ALARM RELEASE BOX (For 100~240VAC or 24VAC or 24VDC) INSTRUCTION MANUAL WARNING 1. CAUTION: Review all installation instructions, procedures, cautions and warnings contained within this manual
More informationSTANDARD FEATURES SPECIFICATIONS
MAG LOCK P/N 300768 STANDARD FEATURES Holding Force: 1500 lbs.(675 Kg.) Easy Installation: Versatile mounting bracket for new and existing doors and frames. Sensor: Built-in Hall effect crystal affected
More informationSOLID STATE SECURITIES, INC. THE "SS90" SERIES RELEASE DEVICES MADE IN THE U.S.A. SS90-WPS MODEL A/B INSTALLATION MANUAL
S S S S S S LISTED L * PATENT PENDING S S 90 OLID TATE ECURITIES, INC SOLID STATE FAIL-SAFE UNIT U 99Y9 RESET RELEASING DEVICE SOLID STATE SECURITIES, INC. THE "SS90" SERIES RELEASE DEVICES MADE IN THE
More informationTABLE OF CONTENTS GENERAL... 2 A. DEFINITIONS DIGITAL, ADDRESSABLE FIRE ALARM SYSTEM... 2
Division 28 ELECTRONIC SAFETY AND SECURITY TABLE OF CONTENTS 28 0000 GENERAL... 2 A. DEFINITIONS...2 28 3111 DIGITAL, ADDRESSABLE FIRE ALARM SYSTEM... 2 A. DESIGN REQUIREMENTS...2 B. CONSTRUCTION REQUIREMENTS...2
More informationBL41 Extra-long Barrier
BL41 Extra-long Barrier NAM-BL41-ES-EN-A 1/8g ENGINEERING SPECIFICATIONS BL41 Extra-long Barrier PART I GENERAL SECTION 08 34 56 Security Gates SECTION 11 12 33 Parking Gates SECTION 28 13 00 Access Control
More informationcsw-200 intro d u c t i o n
csw-200 intro d u c t i o n The CSW-200-UL is The most popular of all swing gate operating systems in the country. It is designed with a non-scissor action arm that will greatly reduce the chance of injury.
More informationInstalling the Cisco ONS FAP-4 Fuse Alarm Panel
Installing the Cisco ONS 15454-FAP-4 Fuse Alarm Panel Product Number: 15454-FAP-4= This document explains how to install, test, operate, and maintain the Cisco ONS 15454-FAP-4 fuse alarm panel. This document
More informationG SERIES: Security INTEGRATION as you want it. Greater expansion, communication, video integration, system resilience, and automation.
G SERIES: Security INTEGRATION as you want it Greater expansion, communication, video integration, system resilience, and automation. G Series Integrated Security Solution Fire Intrusion Access Greater
More informationRCR-REX Request-to-Exit Dual Technology Motion Sensor Installation Guide
RCR-REX Request-to-Exit Dual Technology Motion Sensor Installation Guide Introduction This is the Interlogix RCR-REX Request-to-Exit Dual Technology Motion Sensor Installation Instructions for models RCR-REX-W,
More information3510 East Atlanta Avenue, Phoenix, AZ USA
ACCESS CONTROL VEHICLE DETECTION SOLUTIONS FROM EBERLE DESIGN (EDI) & RENO A&E (RAE) Rev. C 14Dec16 WHS CGZ COPYRIGHT Eberle Design, Inc. 2016 2017. ALL RIGHTS RESERVED. 3510 East Atlanta Avenue, Phoenix,
More informationHARDwired Installation/ Owner s Manual
HARDwired Installation/ Owner s Manual Use this manual for circuit - Revision L or higher. For Models:,, and Multi-Door Access Controller Wiegand Compatable --R-- Provides Access Control System to manage
More informationMADE IN THE U.S.A. MODELS A/B INSTALLATION MANUAL
RELEASE DEVICES MADE IN THE U.S.A. MODELS A/B INSTALLATION MANUAL U.L. LISTED CANADIAN LISTED CSFM: 7300-1418:100 GENERAL DESCRIPTION: S/N: These Time Delay Release Devices are U.L. Listed, Canadian Listed,
More informationTHE "SS90" SERIES RELEASE DEVICES MADE IN THE U.S.A. MODELS A/B INSTALLATION MANUAL
S S S S S S OLID TATE ECURITIES, INC S S 90 SOLID STATE FAIL-SAFE UNIT * PATENT PENDING LISTED 99Y9 RESET U L RELEASING DEVICE SOLID STATE SECURITIES, INC. THE "SS90" SERIES RELEASE DEVICES MADE IN THE
More informationMANUAL RESET ALARM RELEASE
Fire Door Release MODEL AR-D2 MANUAL RESET ALARM RELEASE INSTRUCTION MANUAL AR-D2 GENERAL INFORMATION 1. Review all installation instructions, procedures, cautions and warnings contained within this manual
More informationACSI MODEL 1410 POWER SUPPLY INSTALLATION INSTRUCTIONS
II 1400-3 ACSI MODEL 1410 POWER SUPPLY INSTALLATION INSTRUCTIONS Features: For use with doors or groups of doors that must interlock with each other to regulate control of accessing one area from another,
More informationEVO192 v3.0 Fire and Burglary What s New
EVO192 v3.0 Fire and Burglary What s New Compatibility: EVO192 v3.0 TM50 v1.31 K641 v2.41 Overview: CP-01 Compliancy Wiring Diagram The following sections/options have been added to the EVO192 panel. They
More informationGate Mount Pool Alarms
Home Products About GRI Contact GRI Where to Buy Testimonials What's New! Gate Mount Pool Alarms GT10-2/GT10-4 Microprocessor Controlled Monitors Entry to Pool and Spa Areas Weather Resistant for Outdoor
More informationM O D E L S F I R E G A R D M C V ADVANCE FIRE CONTROL RELEASE DEVICE
Cookson 100 Elmwood Avenue Crestwood Industrial Park Mountaintop, PA 18707 Phone: 800-233-8366 Fax: 800-526-0841 CornellCookson.com O W N E R S M A N U A L M O D E L S F I R E G A R D M C F I R E G A R
More informationSensors and Detectors
12/12/2017 Sensors and Detectors - Clipsal by Schneider Electric Sensors and Detectors Add sensors and detectors to make an environment smarter and more efficient. C-Bus sensors and detectors allow environmental
More informationMADE IN THE U.S.A. ADVANCE FIRE CONTROL MODEL LM21-AFC MANUAL RELEASE DEVICES TEST WEEKLY TO ASSURE PROPER OPERATION OF RELEASE DEVICE/CONTROL PANEL
RELEASE DEVICES MADE IN THE U.S.A. ADVANCE FIRE CONTROL MODEL LM21-AFC MANUAL The LiftMaster Fire Control (LM21-AFC) Release Device/Control Panel is UL/CUL listed normally energized fail-safe device incorporating
More informationWFDE Series Waterflow Detector
WFDE Series Waterflow Detector The System Sensor WFDE series is compatible with pipe diameters ranging from 50mm through 200mm and can be mounted in a vertical or horizontal position. Features Compliant
More information631RF Amp Power Supply
631RF - 1.5 Amp Power Supply Modular Access Control Power Supply Field Selectable 12VDC or 24VDC Output - Standard Dual 12VDC and 24VDC Output - Optional Quality, Performance and Versatility The SDC 631RF
More informationPSC-BL-I-FM-DC0(-BLE) Bi-level Dimming PIR Sensor
TECHNICAL SPECIFICATIONS PSC-BL-I-FM-DC0(-BLE) Bi-level Dimming PIR Sensor Overview Quad Element PIR sensor 0-10V configurable output: set to 0% (OFF)*, 10%, 25% or 50% dimming Photocell for ambient light
More information232xt Wiring Diagrams and Specifications SPECIFICATIONS: REV 1.01
232xt Wiring Diagrams and Specifications Voltage Selection Settings 1 2 3 Wire Xtreme Pad color to color to the wires on Programmer (Red to Red, ect.) ( / Yellow ) Position 12-24VA 15-24VD P5* Position
More informationPOWER SOURCES MODEL NO. DESCRIPTION PRICE
POWER SOURCES BE-961-1 BE-961-2 BE-961-5 BE-961-6 Battery Eliminator - 120VAC to 9VDC Includes 10 Flex Conduit and Transformer Powers up to 3 ECLs or 3 EBs Battery Eliminator - Same as above with Supervisory
More information5900 Series X-in Low Energy Power Operator
5900 Series X-in Low Energy Power Operator INTRODUCTION The Norton 5900 Series X-in is a full-featured, extremely quiet, low energy door operator designed for moderate to high traffic doors. This cost-effective
More informationModel Gas Alarm Panel APPLICABILITY & EFFECTIVITY. This manual provides instructions for the following Sierra Monitor products:
Model 2102 Gas Alarm Panel APPLICABILITY & EFFECTIVITY This manual provides instructions for the following Sierra Monitor products: Model Description 2102-00 Alarm Panel 2 Channel 2102-01 Alarm Panel 2
More informationUK MADE GSM SOLUTIONS
UK MADE GSM SOLUTIONS ACTIVATION AND CONTROL FOR YOUR EVERYDAY ELECTRONICS USING YOUR MOBILE PHONE E: sales@gsm-activate.co.uk T: 01273 462380 www.gsm-activate.co.uk ABOUT GSM ACTIVATE GSM Activate is
More informationPower Transfer Devices. Access Control Accessories. How To Order. How to Order
Power Transfer Devices Door Cord (TSB-C) Simplest and most economical solution for power transfer Standard with Touch Sense Bar and MGL but may also be purchased separately Consists of an 18 [460mm] or
More informationVIDEO VISITATION APPLICATION: FUNCTIONS AVAILABLE:
VIDEO VISITATION S E C U R I T Y E L E C T R O N I C S APPLICATION: SecurVu Video Visitation provides a robust IP-based solution custom designed for the harsh correctional environment. Facilities of any
More informationInstallation and Operation Manual. Model Q916
Installation and Operation Manual Model Q916 This manual is suitable for the following components: Part Number Description PANQ916KS Kit (Silver door, silver master room, power supply) PANQ916KG Kit (Grey
More informationRemote Display Alarm Indicator for Oxygen monitor
Remote Display Alarm Indicator for Oxygen monitor (Part number 99091) The Remote Display Alarm Indicator is designed to display remote oxygen concentration information from PureAire oxygen monitors. All
More informationSystem Design and Overview Document
System Design and Overview Document Power Calculations: This is one the most important tasks when designing your system. You must add up worst case current draw of your system. The power supply contained
More informationDOOR MONITORING/DURESS SYSTEM
SECTION PART 1 - GENERAL 1.1 RELATED SECTIONS A. Comply with the requirements of Section 27 05 00 Common Work Results for Communications. 1.2 DEFINITIONS A. Not used. 1.3 DESCRIPTION OF SYSTEM: A. Provide
More informationMODEL B2 INSTALLATION MANUAL
RELEASE DEVICES GENERAL DESCRIPTION MODEL B2 INSTALLATION MANUAL S/N: The B2 Series Time Delay Release Devices are UL Listed, Canadian Listed, and CSFM Listed for use on rolling doors, single-slide and
More informationChicken Door User Manual
Chicken Door User Manual Introduction This chicken door incorporates a linear actuator to horizontally slide the existing door of the hen house. The door opens just after dawn and closes just after dusk
More informationSECTION LOW VOLTAGE LIGHTING CONTROLS
SECTION 26 09 26 LOW VOLTAGE LIGHTING CONTROLS PART 1 - GENERAL 1.01 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and Section
More informationELITE SERIES COMMERCIAL HIGH-TRAFFIC AC SLIDE GATE OPERATOR
ELITE SERIES COMMERCIAL HIGH-TRAFFIC AC SLIDE GATE OPERATOR INSTALLATION MANUAL Model SL3000UL SL3000101UL 1 HP Single Phase SL3000501UL 1/2 HP Single Phase THIS PRODUCT IS TO BE INSTALLED AND SERVICED
More informationIntelligent Single Loop Fire Alarm Control Panel
Intelligent Single Loop Fire Alarm Control Panel The CAX-CTL-1L Intelligent Single Loop Fire Alarm Control Panel is a member of the industry leading Axis AX Series Intelligent Fre Alarm Control Panels
More informationSection 1: General Description. Section 2: Features. Section 3: Operation. CM-RQE70 PIR REQUEST TO EXIT DETECTOR Installation Instructions.
CM-RQE70 PIR REQUEST TO EXIT DETECTOR Installation Instructions 1 PACKAGE CONTENTS Wiring Harness 6 Wire Nuts #6 x 3/4 Screws s BP7175 3/16 Wall Plugs Section 1: General Description Camden CM-RQE-70 Request-to-Exit
More informationFIREFLY II PLUS RELEASE DEVICES INSTALLATION MANUAL
FIREFLY II PLUS RELEASE DEVICES INSTALLATION MANUAL MADE IN THE U.S.A. U.L. LISTED CANADIAN LISTED CSFM: 7300-1418:100 GENERAL DESCRIPTION SERIAL NUMBER The Cookson Company FIREFLY II PLUS Time Delay Release
More informationThe system should also be capable of recording events automatically on any compatible DVR and should be able to retrieve recordings based on events.
0BThe System The Security Management System should be capable of Controlling and Monitoring Access through the doors, Monitor and control Inputs and Outputs, include an Integrated Video Badging, Integrate
More informationCM-RQE70 PIR REQUEST TO EXIT DETECTOR
Door Activation Devices CM-RQE70 PIR REQUEST TO EXIT DETECTOR THIS PACKAGE INCLUDES (1) Wiring Harness (2) #6 x 3/4" Screws (2) 3/16" Wall Plugs (6) Wire Nuts (2) 's BP7175 1. GENERAL DESCRIPTION Camden
More informationTPW-900ETS01. Product Manual. Intelligent Swing Gate Turnstile
TPW-900ETS01 Intelligent Swing Gate Turnstile Product Manual Contents Product Description... 1 Structure Chart... 2 Dimension Figure Unit mm... 2 Product Parameters... 3 Product Function... 3 Custom-made
More informationOperating & Maintenance Manual. Alert-4 Ethernet LCD Master Alarm
Operating & Maintenance Manual Alert-4 Ethernet LCD Master Alarm w w w. a m i c o. c o m Contents User Responsibility 4 Introduction 4 Features 5 Description of the Alarm 5 Shipment Details 5 The Alarm
More informationAutomatic swing door solutions. We make access in life smart and secure.
Automatic swing door solutions We make access in life smart and secure. dormakaba Automatic swing door solutions Entrance solutions by dormakaba Security. Sustainability. Reliability. ED100 low energy
More informationColumbia Boat Alarms, Inc.
Columbia Boat Alarms, Inc. Model 411 Installation Manual http://www.columbiaboatalarms.com sales@columbiaboatalarms.com 4/4/2017 Forward Thank you for purchasing our Model 411 Columbia Boat Alarm! The
More informationTHE. Series 01 and 02. MG01C Package
THE Series 01 and 02 124 Springville Road Unit 3 Hampton Bays, New York 11946 Phone: (800) 648-4301 (631) 728-3986 Fax: (631) 728-3931 www.marineguard.net MG01C Package Each year, more people are turning
More informationAutomations and ACLinks. Technical Support Engineering Rosslare Security NA For more information please see
Automations and ACLinks Technical Support Engineering Rosslare Security NA For more information please see www.axtraxng.com AC Links are used to create automations and perform custom operations on access
More informationDETECTING WRONG WAY DRIVERS. Lynne Randolph Southwest Research Institute (210)
DETECTING WRONG WAY DRIVERS Lynne Randolph Southwest Research Institute (210) 522-3386 lynne.randolph@swri.org BACKGROUND 2 WIDESPREAD ISSUE ACROSS MULTIPLE STATES 3 WHAT ARE THE CAUSES? Impaired driving
More informationOPERATOR S MANUAL. BASIC PROJECT CENTERS Some instructions and drawings may not apply to your specific unit. SAFETY SERVICE PARTS CAPACITIES
OPERATOR S MANUAL BASIC PROJECT CENTERS Some instructions and drawings may not apply to your specific unit. SERVICE PARTS LOCATING MODEL # INFORMATION Model number and other information required for service
More informationSIA/IAPSC CAD Security Symbols
APPENDIX A TABLE OF SYMBOLS (This Appendix shall be considered a fully binding part of this standard.) 1. ANNOTATION 1.01 REF Device Reference A: Drawing Sheet B: Detail C: Device / Zone Number 2. ACCESS
More informationAccessories. Desk Top Controls
Accessories Desk Top Controls 15-2 15-1 15-3 15-2-3 DTMO-1 DTMA-1 Under Desk Top Mounting The SDC 15 series switch controls are mounted on the underside of a desk for remote door control. They may be connected
More informationSPEC SHEET. Simple Expansion Solutions ZONE EXPANSION MODULES: SINGLE AND MULTIPLE POINT
SPEC SHEET Simple Expansion Solutions Expand your DMP panel options with a wide array of expansion modules. Add supervised Class B burglary zones. Connect non-powered burglary or fire type devices for
More informationCM-RQE70A PIR REQUEST TO EXIT DETECTOR
Door Activation Devices CM-RQE70A PIR REQUEST TO EXIT DETECTOR THIS PACKAGE INCLUDES (2) #6 x 3/4" Screws (2) 3/16" Wall Plugs (2) MOV's BP7175 1. GENERAL DESCRIPTION Camden CM-RQE70A Request-to-Exit Sensor
More informationINSTALLATION MANUAL. * If using remote sensors the thermostat must be hardwired. Need Help?
INSTALLATION MANUAL This manual covers the following models: T955W Master Thermostat Base Module Thermostat Applications Guide Description Gas or Oil Heat Electric Furnace Heat Pump (No Aux. or Emergency
More informationTS93 EMF SERIES. INSPK NO Rev.03/10
TS93 EMF SERIES 1 Each hold open (HO) unit contains a door closer and track assembly with hold open solenoid. The unit can be connected directly to a fire control panel. 1) Read the entire instruction
More informationUBC Technical Guidelines Section Edition Access Control Page 1 of 5
Page 1 of 5 1.0 GENERAL 1.1 Related UBC Guidelines.1 Section 28 05 00 Access Services: General Standards.2 Section 08 71 00 Door Hardware 1.2 Coordination Requirements.1 UBC Access Services 1.3 Description.1
More informationYOUR SCHOOL STAFF NEEDS PROTECTION
YOUR SCHOOL STAFF NEEDS PROTECTION Threats and assaults on school staff and students are on the rise. They deserve protection. But what is an effective means to notify security personnel and school officials
More informationSmart Security at Every Corner of Your Home
Floodlight Cam Smart Security at Every Corner of Your Home Your new Ring Floodlight Cam lets you extend the Ring of Security around your entire property. Now, you ll always be the first to know when someone
More information4700 SERIES PLC INTERLOCK CONTROLLER
4700 SERIES PLC INTERLOCK CONTROLLER The 4700 series PLC interlock controller is a self-contained, cost effective controller for operating door interlock and mantrap systems of up to 4 doors or for many
More informationAL400ULACM AL600ULACM - 4 amp - 12VDC or 6 amp. - Fused Outputs - Fused Outputs
ACM Series Access Power Controllers with Power Supplies Installation Guide Models Include: AL400ULACM AL600ULACM - 12VDC @ 4 amp - 12VDC or 24VDC @ 6 amp. or 24VDC @ 3 amp - Fused Outputs - Fused Outputs
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationPowers TM Controls ET 134 Line Voltage Room Thermostats
Powers TM Controls ET 134 Line Voltage Room Thermostats Technical Instructions Document No. 155-017P25 ET 134-55 134-1083 134-1084 &134-1085 Exposed Knobs 134-1084 & 134-1085 Concealed Adjustment 134-1086
More informationTEC1100 Series Thermostats
Metasys Network Sales Resource Manual 635 Application Specific Controllers Section Product Bulletin Issue Date 0601 TEC1100 Series Thermostats TEC1100 is a series of non-programmable thermostats with a
More informationNetworX NX-548E Receiver Installation Instructions
NetworX NX-548E Receiver Installation Instructions Content Introduction... 1 Internal mounting... 1 External mounting... 2 Wiring... 3 DIP switch settings... 3 Power up... 3 Programming... 4 Testing and
More informationTouch Screen Thermostat. MTSC/SUPER, MTSC24/SUPER Series. MTS/SUPER, MTS24/SUPER Series. Owner s manual and technician settings
Touch Screen Thermostat MTSC/SUPER, MTSC24/SUPER Series MTS/SUPER, MTS24/SUPER Series Owner s manual and technician settings -2 - Index 1. Owner s Manual... 4 1.1 Quick Guide. 4 1.2 Turning the unit ON
More informationFALCO Access Control. Product Training
FALCO Access Control Product Training FALCO are leaders in the design and manufacture of state of the art access control and security solutions. Since our inception in 2000, over 100,000 FALCO systems
More informationTRX MAINS CONNECTION DIAGRAM
TRX MAINS CONNECTION DIAGRAM Switch 230VAC 10A Neutral Out Phase Out TRX MAINS Phase In Neutral In LOAD 8A MAX. Specifications: Operating Voltage: 220-240VAC 50Hz Current Draw: 5mA Max. Switching Current:
More informationPLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLING THE SYSTEM. HANDLE THE EQUIPMENT CAREFULLY.
575 Birch Street, Forestville, CT 06010 Phone (866) 322-1237 Fax (866) 322-1233 WWW.LOCKNETICS. CL-CONTROLLER CL-CONTROLLER UNLIMITED USERS ALLOWED 2000 AUDIT EVENTS SOFTWARE-MANAGED TIME ZONES SOFTWARE-MANAGED
More informationELITE SERIES COMMERCIAL HIGH-TRAFFIC AC SWING GATE OPERATOR
ELITE SERIES COMMERCIAL HIGH-TRAFFIC AC SWING GATE OPERATOR INSTALLATION MANUAL Model CSW200UL THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY. This model is for
More informationMulti-Output Access Control Power Supply Chargers VDC or 24VDC VDC or 4 24VDC.
M Series Multi-Output Access Control Power Supply Chargers Installation Guide Models Include: AL300ULM AL400ULM - 2.5 amp @ 12VDC or 24VDC. - 3 amp @ 12VDC or 4 amp @ 24VDC. AL600ULM AL1012ULM - 6 amp
More informationSummer Breeze Heater Service Manual
Summer Breeze Heater Service Manual RSBH RSBH-SB RSBHP Revision: 1.0 Issued: 12-18-2012 Table of Contents I. Basic Assembly and Operation A. Safety Instructions... 2 B. Grounding Instructions... 3 C.
More informationControl Panels. Control Panels for Commercial Applications. Control panels provide the central processing
Control Panels Control Panels for Commercial Applications Control panels provide the central processing and logic for an integrated system. In a typical system, there are four major functions: inputs,
More informationSECTION LIGHTING CONTROLS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 09 23 LIGHTING CONTROLS SPEC WRITER NOTE: 1. Delete between //----// if not applicable to project. Also, delete any other item or paragraph not applicable to
More informationCimco Series 21. Series 21 - Specifications INDEX. Description. Operational Specification 2
Series 21 - Specifications INDEX Description Page Operational Specification 2 Analog Operational Specification - Communications Options 3 Digital Operational Specification - Communications Options 4 Hardware
More informationFlexZone SIX STEPS TO AFFORDABLE PERIMETER PROTECTION EASY TO INSTALL LOW TOTAL COST OF OWNERSHIP HASSLE-FREE OPERATION & MAINTENANCE HOW-TO GUIDE
FlexZone HOW-TO GUIDE SIX STEPS TO AFFORDABLE PERIMETER PROTECTION EASY TO INSTALL LOW TOTAL COST OF OWNERSHIP HASSLE-FREE OPERATION & MAINTENANCE Detect intruders BEFORE they get in By itself, your expensive
More information