2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F E. cristalcontrols.

Transcription

1 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F E. info@cristalcontrols.com cristalcontrols.com TM

2 Index Quick Selection Which Technology to use...4 Retrofit Ceiling Occupancy Sensor...5 Low Voltage Ceiling Occupancy Sensor...10 Line Voltage Ceiling Occupancy Sensor...16 Line Voltage Ceiling Occupancy Sensor, 347VAC Retrofit Wall Switch Occupancy Sensor...27 Low Voltage Wall Switch Occupancy Sensor Low Voltage Wall Mount Occupancy Sensor Line Voltage Wall Switch Occupancy Sensor Line Voltage Wall Switch Occupancy Sensor, 347V Pole Power Pack ( ) Pole Power Pack (347-1) Pole Power Pack ( ) Sensor Settings Warranty Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com

3 Quick Selection Chart CCORSDD1-N-N (Retrofit Applications Only) CEILING LOW VOLTAGE Ceiling Recessed, Std Lens, Dual Tech, 24V, 1P 3 CCORSDD1-R-N Ceiling Recessed, Std Lens, Dual, 24V, 1P, Rly 3 CCORSDD2-N-N Ceiling Recessed, Std Lens, Dual Tech, 24V, 2 Pole 8 CCORSDD2-R-N Ceiling Recessed, Std Lens,Dual Tech, 24V, 2 Pole, Rly 8 CCORXDD2-PR-N Ceiling Recessed, Ext Lens, Dual Tech, 24V, 2P, Ph, Rly 8 CCORSDD2-DPR-L Ceiling Rec, Std Lens, Dual Tech, 24V, 2P, Dim, Ph, Rly, LT 8 CCORXDD2-DPR-L Ceiling Rec, Ext Lens, Dual Tech, 24V, 2P, Dim, Ph, Rly, LT 8 PAGE CEILING LINE VOLTAGE PAGE CCORBIU2-P-N Ceiling Recessed, High Bay, PIR, 120/277, 2P, Photo 14 CCORSDU1-P-N Ceiling Recessed, Std Lens,Dual Tech, 120/277, 1P, Photo 14 CCORSDU2-P-N Ceiling Recessed, Std Lens, Dual Tech, 120/277, 2P, Photo 14 CCORXDU2-P-L Ceiling Recessed, Ext. Lens, Dual Tech, 120/277, 2P, Photo 14 CCORSD31-P-N Ceiling Recessed, Std Lens, Dual Tech, 347, 1P, Photo 20 CCORSD32-P-N Ceiling Recessed, Std Lens, Dual Tech, 347, 2P, Photo 20 CCORXD32-P-N Ceiling Recessed, Ext. Lens, Dual Tech, 347, 2P, Photo 20 CCOSSDD1-P-VW (Retrofit Applications Only) WALL SWITCHES LOW VOLTAGE Switch Mt Sensor, Dual Tech, 24V, 1P, Photo, Vandal, White 25 CCOSSDD2-P-VW Switch Mt Sensor, Dual Tech, 24V, 2P, Photo, Vandal, White 30 CCOSSDD2-DPR-VW Switch Mt Sensor, Dual Tech, 24V, 2P, Dim, Ph, Rly, Vandal, W 30 PAGE WALL MOUNT (Corner, aisles etc ) PAGE CCOWCDD2-R-N Wall Mount Sensor, Corner Lens, Dual Tech, 24V, 2P, Rly 36 CCOWLDD2-R-N Wall Mount Sensor, Large Area Lens, Dual Tech, 24V, 2P, Rly 36 CCOWCDD2-DPR-N Wall Mt Sensor, Corner Lens, Dual Tech, 24V, 2P, Dim, Ph, Rly 36 3

4 Quick Selection Chart & Which Technology to use WALL SWITCHES LINE VOLTAGE PAGE CCOSSDU1-P-VW Switch Mt Sensor, Dual Tech, 120/277, 1P, Photo, Vandal, White 41 CCOSSDU2-P-VW Switch Mt Sensor, Dual Tech, 120/277, 2P, Photo, Vandal, White 41 CCVSSDU2-P-VW Switch Mt Vac. Sensor, Dual Tech, 120/277, 2P, Photo, Vandal, White 41 CCOSSD31-P-VW Switch Mt Sensor, Dual Tech, 347, 1P, Photo, Vandal, White 46 CCOSSD32-P-VW Switch Mt Sensor, Dual Techl, 347, 2P, Photo, Vandal, White 46 POWER PACK PAGE CCP-PP20-D Power Pack, 120/277, 20A, 1P, 24VAC power, Diode Pulse 51 CCP-PP20-2P Power Pack, 120/277, 20A, 2P, 24VAC power, Diode Pulse 54 CCP-PP D Power Pack, 347, 20A, 1P, 24VAC power, Diode Pulse 57 CCIR-3110 PROGRAMMER IR Handheld Remote Programmer Ceiling Sensor Wall Switch Wall Sensor LOCATION PASSIVE INFRARED PIR UNTRASONIC DUAL TECHNOLOGY SENSOR TYPE % SAVINGS Bedroom X 1 2 Cafeteria X Classroom X X 2 40 Closet/Storage X X Conference Room X X Hallway X 2 3 Lecture Hall X 2 Library X 2 Lobby X Private Office X X X Rest Room Multi Stall X X Warehouse X

5 Retrofit Ceiling Occupancy Sensor Technical Data Part No CCORSDD1-N-N CCORXDD1-N-N Description The Diversa occupancy sensors use PIR and ADI-Voice technologies to determine the presence of people and perform the control actions when occupancy (or vacancy) is detected. The CCOR Séries of sensors are designed to mount recessed on a ceilings giving a 360 coverage pattern. The low voltage edition of this sensor gives the capability of operating and controlling the CCP-PP20-D Power Pack and/or diode pulse relays. Specification Inputs 24 VAC +/- 25% Class 2 Low Voltage Source 60 Hz Use #18AWG wire Outputs Diode Pulse : Each output is capable of driving one Diode Pulse Relay Power consumption 9,5 ma Standard Approvals FCC Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 14 F to 140 F (-10 C to 60 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) Features Recessed ceiling mounted occupancy sensor provides 360 coverage using an adjustable swivel head to optimize the sensor area. The dual-tech sensor utilizes ADI-Voice Technology, which has advanced digital signal processing for accurate detection of human speech. A Self-adapting mode can be set to use both Passive Infrared (PIR) & Accurate Detection Intelligence (ADI) Voice technologies to automatically track occupancy tendencies for continuous maximizing of energy savings. Smart Sensing allows for an immediate return to occupied mode in the event of a false off being triggered. Can be programmed by on-board DIP switches and dials or an IR Setting Unit for added convenience, especially during commissioning Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com Operation Low voltage sensors are powered by 24VAC from either the CCP-PP20-D Power Pack or a 24VAC transformer. When in operation, the sensor will detect initial motion using PIR; once motion is detected the internal contact will close. The ADI-Voice is then activated to work alongside the PIR to detect occupancy. cristalcontrols.com 5

6 Retrofit Ceiling Occupancy Sensor Technical Data & Details Dimensions & Mounting Unit attaches to mounting ring with screws or it can be mounted into an octagon box. The CCOR sensor will fit an octagon box. It is very important that conduits be attached at opposite ends of the box. Use a 2-1/8 or more, deep box. If the box is less, use the spacer ring. Wiring Instructions The CCOR Series Trickle Current sensors are equipped with #22 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. Electrical Connections Wiring to a Power Pack Wiring to a Relay Panel Sensor Settings (See page for Sensor Setting description) 1. Programming - IR / Manual Setting 2. Detection (Dual or PIR Only) 3. Vacancy Sensor 4. Smart Sensing 5. Automatic Timeout 6

7 Retrofit Ceiling Occupancy Sensor Details & Coverage Installation Installing in Smaller Room (Standard Lens) f Locate the sensor near the entrance door wall to prevent it from viewing out into the hallway. f The lens can rotate, allowing the sensor to be pointed toward the area in front of the entrance door. f Positioning the sensor in this manner ensures that an occupant moves across the longest detection beam upon entrance, utilizing the sensor's maximum PIR range. Standard Lens (S) f Optimal usage is to detect small motions such as hand movements f Designed for a mounting height of 7-15ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy 7

8 Retrofit Ceiling Occupancy Sensor Details & Coverage Extended Lens (X) f Optimal usage is to detect small motions such as hand movements f Designed for a mounting height of 7-15ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy Installing in Larger Room (Extended Lens) f Place the sensor near the center of the room ceiling. Locate it so the approximate distance of 27ft in and over (A & B) or in dead center of room. f Tilt the lens to ai m the detection zone to the bottom of the door. (C) f Positioning the sensor in this manner ensures that the beam does not reach outside the room without reducing sensitivity. * Application and Performance Specification Information Subject to Change without Notification 8

9 Retrofit Ceiling Occupancy Sensor Installation Installation & Wiring Directions Installation Mounting of the device requires a 2-1/8 deep or more, octagonal junction box. Install by recessing the device into the octagon box; lining up the mounting holes and securing it using the screws provided. If too shallow, use the spacer ring is provided. Wiring The WOR Series Retrofit sensors are equipped with plug-in harness for easy installation. This harness has #20 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. White 24 Vac Bleu DO NOt USE Red Primary output pole Red/White Not Used Orange Not Used Yellow/Black Not Used Yellow Not Used Yellow/White Not Used Violet(+) Not Used Grey (-) Not Used DIP Switches A bank of eight DIP switches and two rotating controls can be used to manually setup and configure the sensor. CCOR*DD1-N-N DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) ON 5 Not Used N/A N/A OFF 6 Not Used N/A N/A OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 9

10 Low Voltage Ceiling Occupancy Sensor Technical Data Specification Inputs 24 VAC +/-25% Class 2 Low Voltage Source 60Hz Use #18WG wire Part No CCORSDD2-N-N CCORSDD2-R-N CCORSDD2-DPR-L CCORXDD2-PR-N CCORXDD2-DPR-L Description The Diversa occupancy sensors use PIR and ADI-Voice technologies to determine the presence of people and perform the control actions when occupancy (or vacancy) is detected. The CCOR Series of sensors are designed to mount recessed in to a ceiling space providing a 360 coverage pattern. The low voltage edition of this sensor gives the capability of operating and controlling the CCPPP20-D Power Pack and/or diode pulse relays. Outputs Diode Pulse : Each output is capable of driving up to four Diode Pulse relays. 0-10V Dimming : Use to control up to 50 Ballasts. Connections are polarity sensitive. LED drivers can connect up to 25mA Aux Relay : SPDT Form-C contact rated for 1A at 30VDC Power consumption 9.5 ma Standard 14.0 ma with Auxiliary Relay Approvals FCC Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 14 F to 140 F (-10 C to 60 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) Low temp and high humidity option [-L] products: PCB conformal coated for resistance to damp environments and operation to -40 C/F Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com Features Recessed ceiling mounted occupancy sensor provides 360 coverage using an adjustable swivel head to optimize the sensor area. The dual-tech sensor utilizes ADI-Voice Technology, which has advanced digital signal processing for accurate detection of human speech. A Self-adapting mode can be set to use both Passive Infrared (PIR) & Accurate Detection Intelligence (ADI) Voice technologies to automatically track occupancy tendencies for continuous maximizing of energy savings. Smart Sensing allows for an immediate return to occupied mode in the event of a false off being triggered. The photo sensor option is available to provide a 0-10VDC dimming ballast/led* Drivers output for Daylight Harvesting. * LED drivers up to 25mA, please contact driver manufacturer for currents Can be programmed by on-board DIP switches and dials or an IR Setting Unit for added convenience, especially during commissioning. cristalcontrols.com 10

11 Low Voltage Ceiling Occupancy Sensor Technical Data & Details Operation Line voltage sensors draw control power directly from the lighting circuit they are intended to control. When in operation the sensor will detect initial motion using PIR; once motion is detected, the internal contact will close. ADI-Voice is then activated to work alongside PIR to maintain the occupied condition as long as people are within the sensing range. Dimensions & Mounting Unit attaches to mounting ring with screws or it can be mounted into an octagon box. The CCOR sensor will fit an octagon box. It is very important that conduits be attached at opposite ends of the box. Use a 2-1/8 or more, deep box. If the box is less, use the spacer ring. Wiring Instructions The CCOR Series Line Voltage sensors are equipped with #22 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. Electrical Connections CCP-PP20-D 11

12 Low Voltage Ceiling Occupancy Sensor Technical Data & Details Sensor Settings (See page for Sensor Setting description item) 1. Programming - IR / Manual Setting 2. Detection (Dual or PIR Only) 3. Automatic Timeout 4. Smart Sensing 5. Vacancy Sensor 6. Photo Sensing (-P) 7. Daylight Harvest Dimming (0-10V Output) (-D) 8. Multi-Level Switching (2-Pole w/o Photo Sensing option) 9. Multi-Level Photo Sensing (2-Pole w/ Photo Option) 10. Sensor Link 12

13 Low Voltage Ceiling Occupancy Sensor Details & Coverage Installation Installing in Smaller Room (Standard Lens) f Locate the sensor near the entrance door wall to prevent it from viewing out into the hallway. f The lens can rotate, allowing the sensor to be pointed toward the area in front of the entrance door. f Positioning the sensor in this manner ensures that an occupant moves across the longest detection beam upon entrance, utilizing the sensor's maximum PIR range. Standard Lens (S) f Optimal usage is to detect small motions such as hand movements f Designed for a mounting height of 7-15ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy Extended Lens (X) f Optimal usage is to detect small motions such as walking f Designed for a mounting height of 7-15ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy 13

14 Low Voltage Ceiling Occupancy Sensor Details & Coverage Installing in Larger Room (Extended Lens) f Place the sensor near the center of the room ceiling. Locate it so the approximate distance of 27ft in and over (A & B) or in dead center of room. f Tilt the lens to aim the detection zone to the bottom of the door. (C) f Positioning the sensor in this manner ensures that the beam does not reach outside the room without reducing sensitivity. Installation & Wiring Directions Installation Mounting of the device requires a 2-1/8 deep or more, octagonal junction box. Install by recessing the device into the octagon box; lining up the mounting holes and securing it using the screws provided. If too shallow, use the spacer ring is provided. Wiring The CCOR Series Low Voltage sensors are equipped with plug-in harness for easy installation. This harness has #20 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. 14

15 Low Voltage Ceiling Occupancy Sensor Installation DIP Switches A bank of eight DIP switches and two rotating controls can be used to manually setup and configure the sensor. CCOR N - DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) ON 5 Not Used N/A N/A OFF 6 Not Used N/A N/A OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON CCOR P - DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) ON 5* Photocell Inhibit** Disabled Enabled OFF 6* Photocell Control Inhibit 2 nd Pole Only Inhibit Both Poles OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON CCOR DPR - DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) ON 5 Photocell Inhibit** Photocell Disabled & Fixed Dim Level Photocell Enabled + Auto Dim Level 6 Photocell Control* Inhibit 2 nd Pole Only Inhibit Both Poles OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON OFF 15

16 Line Voltage Ceiling Occupancy Sensor Technical Data Specification Power 120/277 VAC 60Hz Part No CCORBIU2-P-N PIR Only CCORSDU1-P-N CCORSDU2-P-N CCORXDU2-P-L Desription The Diversa occupancy sensors use PIR and ADI-Voice technologies to determine the presence of people and perform the control actions when occupancy (or vacancy) is detected. Contact Ratings 120 VAC-800W 277 VAC-1200W Power consumption 5,7 ma Approvals Certified to UL 508, UL244A, CSA C22.2 #14 Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com The CCOR Series of sensors are designed to mount recessed in to a ceiling space providing a 360 coverage pattern. Has an adjustable tilting lens to prevent detection outside monitored space. Features Recessed ceiling mounted occupancy sensor provides 360 coverage using an adjustable swivel head to optimize the sensor area. The dual-tech sensor utilizes ADI-Voice Technology, which has advanced digital signal processing for accurate detection of human speech. A Self-adapting mode can be set to use both Passive Infrared (PIR) & Accurate Detection Intelligence (ADI) Voice technologies to automatically track occupancy tendencies for continuous maximizing of energy savings. Smart Sensing allows for an immediate return to occupied mode in the event of a false off being triggered. Can be programmed by on-board DIP switches and dials or an IR Setting Unit for added convenience, especially during commissioning. Operation Line voltage sensors draw control power directly from the lighting circuit they are intended to control. When in operation the sensor will detect initial motion using PIR; once motion is detected, the internal contact will close. ADI-Voice is then activated to work alongside PIR to maintain the occupied condition as long as people are within the sensing range. Ambient Operating Temperature : 32 F to 104 F (0 C to 40 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) Low temp and high humidity option [-L] products: PCB conformal coated for resistance to damp environments and operation to -40 C/F. Indoor use only. cristalcontrols.com 16

17 Line Voltage Ceiling Occupancy Sensor Technical Data & Details Dimensions & Mounting Unit attaches to mounting ring with screws or it can be mounted into an octagon box. The CCOR sensor will fit an octagon box. It is very important that conduits be attached at opposite ends of the box. Use a 2-1/8 or more, deep box. If the box is less, use the spacer ring. Wiring Instructions The CCOR Series Line Voltage sensors are equipped with #14 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. Electrical Connections CCOR**U*-*-* CCOR**U2*-*-* Sensor Settings (See page for Sensor Setting description) 1. Programming - IR / Manual Setting 2. Detection (Dual or PIR Only) 3. Automatic Timeout 4. Smart Sensing 5. Photo Sensing (-P) 6. Multi-Level Photo Sensing (2-Pole w/ Photo Option) 17

18 Line Voltage Ceiling Occupancy Sensor Details & Coverage Installation Installing in Smaller Room (Standard Lens) f Locate the sensor near the entrance door wall to prevent it from viewing out into the hallway. f The lens can rotate, allowing the sensor to be pointed toward the area in front of the entrance door. f Positioning the sensor in this manner ensures that an occupant moves across the longest detection beam upon entrance, utilizing the sensor's maximum PIR range. Standard Lens (S) f Optimal usage is to detect small motions such as hand movements f Designed for a mounting height of 7-15ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy Extended Lens (X) f Optimal usage is to detect small motions such as walking f Designed for a mounting height of 7-15ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy 18

19 Line Voltage Ceiling Occupancy Sensor Details & Coverage Hi-Bay Lens (B) f Optimal usage is to detect small motions such as walking f Designed for a mounting height up to 40Ft f PIR only Installing in Larger Room (Extended Lens) f Place the sensor near the center of the room ceiling. Locate it so the approximate distance of 27ft in and over (A & B) or in dead center of room. f Tilt the lens to ai m the detection zone to the bottom of the door. (C) f Positioning the sensor in this manner ensures that the beam does not reach outside the room without reducing sensitivity. * Application and Performance Specification Information Subject to Change without Notification 19

20 Line Voltage Ceiling Occupancy Sensor Installation Installation & Wiring Directions Installation Mounting of the device requires a 2-1/8 deep or more, octagonal junction box. Install by recessing the device into the octagon box; lining up the mounting holes and securing it using the screws provided. If too shallow, use the spacer ring is provided. CAUTION TURN POWER OFF AT THE CIRCUIT BREAKER BEFORE WORKING WITH OR NEAR HIGH VOLTAGE Wiring The CCOR Series Line Voltage sensors are equipped with #14 AWG stranded leads. Use appropriate sized wirenuts to connect the wires to the incoming load terminations; for installation with fieldinstalled conductors of 60ºC minimum rating. CCOR**U*-*-* CCOR**U2*-*-* 20

21 Line Voltage Ceiling Occupancy Sensor Installation DIP Switches A bank of eight DIP switches and two rotating controls can be used to manually setup and configure the sensor. CCOR N - DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) ON 5 Not Used N/A N/A OFF 6 Not Used N/A N/A OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON CCOR P - DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) ON 5* Not Used Disabled Enabled OFF 6* Not Used Inhibit 2 nd Pole Only Inhibit Both Pole OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON *Available in 2-Pole models (-2) only 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 21

22 Line Voltage Ceiling Occupancy Sensor, 347VAC Technical Data Specification Power VAC 60Hz Part No CCORSD31-P-N CCORXD32-P-N CCORSD32-P-N Description The Diversa occupancy sensors use PIR and ADI-Voice technologies to determine the presence of people and perform the control actions when occupancy (or vacancy) is detected. The CCOR Series of sensors are designed to mount recessed in to a ceiling space providing a 360 coverage pattern. Has an adjustable tilting lens to prevent detection outside monitored space. Contact Ratings 347 VAC-1200W Power consumption 5,7 ma Approvals Certified to UL 508, UL244A, CSA C22.2 #14 Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 32 F to 104 F (0 C to 40 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) Low temp and high humidity option [-L] products: PCB conformal coated for resistance to damp environments and operation to -40 C/F. Indoor use only. Features Recessed ceiling mounted occupancy sensor provides 360 coverage using an adjustable swivel head to optimize the sensor area. The dual-tech sensor utilizes ADI-Voice Technology, which has advanced digital signal processing for accurate detection of human speech. A Self-adapting mode can be set to use both Passive Infrared (PIR) & Accurate Detection Intelligence (ADI) Voice technologies to automatically track occupancy tendencies for continuous maximizing of energy savings. Smart Sensing allows for an immediate return to occupied mode in the event of a false off being triggered. Can be programmed by on-board DIP switches and dials or an IR Setting Unit for added convenience, especially during commissioning Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com Operation Line voltage sensors draw control power directly from the lighting circuit they are intended to control. When in operation the sensor will detect initial motion using PIR; once motion is detected, the internal contact will close. ADI-Voice is then activated to work alongside PIR to maintain the occupied condition as long as people are within the sensing range. 22

23 Line Voltage Ceiling Occupancy Sensor, 347VAC Technical Data & Details Dimensions & Mounting Unit attaches to mounting ring with screws or it can be mounted into an octagon box. The CCOR sensor will fit an octagon box. It is very important that conduits be attached at opposite ends of the box. Use a 2-1/8 or more, deep box. If the box is less, use the spacer ring. Wiring Instructions The CCOR Series Line Voltage sensors are equipped with #14 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. Electrical Connections CCOR**3*-*-* CCOR**32*-*-* Sensor Settings (See page for Sensor Setting description) 1. Programming - IR / Manual Setting 2. Detection (Dual or PIR Only) 3. Automatic Timeout 4. Smart Sensing 5. Photo Sensing (-P) 6. Multi-Level Photo Sensing (2-Pole w/ Photo Option) 23

24 Line Voltage Ceiling Occupancy Sensor, 347VAC Details & Coverage Installation Installing in Smaller Room (Standard Lens) f Locate the sensor near the entrance door wall to prevent it from viewing out into the hallway. f The lens can rotate, allowing the sensor to be pointed toward the area in front of the entrance door. f Positioning the sensor in this manner ensures that an occupant moves across the longest detection beam upon entrance, utilizing the sensor's maximum PIR range. Standard Lens (S) f Optimal usage is to detect small motions such as hand movements f Designed for a mounting height of 7-15ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy Installing in a Larger Room (Extended Lens) f Place the sensor near the center of the room ceiling. Locate it so the approximate distance of 27ft in and over (A&B) or in dead center of room. f Tilt the lens to aim the detection zone of the bottom of the door (C). f Positioning the sensor in this manner ensures that the beam does not reach outside the room without reducing sensitivity. 24

25 Line Voltage Ceiling Occupancy Sensor, 347VAC Details & Coverage Extended Lens (X) f Optimal usage is to detect small motions such as walking f Designed for a mounting height of 7-15ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy Hi-Bay Lens (B) f Optimal usage is to detect small motions such as walking f Designed for a mounting height up to 40Ft f PIR only 25

26 Line Voltage Ceiling Occupancy Sensor, 347VAC Installation Installation & Wiring Directions Installation Mounting of the device requires a 2-1/8 deep or more, octagonal junction box. Install by recessing the device into the octagon box; lining up the mounting holes and securing it using the screws provided. If too shallow, use the spacer ring is provided. CAUTION TURN POWER OFF AT THE CIRCUIT BREAKER BEFORE WORKING WITH OR NEAR HIGH VOLTAGE Wiring The CCOR Series Line Voltage sensors are equipped with #14 AWG stranded leads. Use appropriate sized wirenuts to connect the wires to the incoming load terminations; for installation with fieldinstalled conductors of 60ºC minimum rating. CCOR**3*-*-* CCOR**32*-*-* 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com DIP Switches A bank of eight DIP switches and two rotating controls can be used to manually setup and configure the sensor. CCOR P - DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) ON 5 Photocell Inhibit** Disabled Enabled OFF 6 Photocell Control Inhibit 2 nd Pole Only Inhibit Both Poles OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON *Available in 2-Pole models (-2) only cristalcontrols.com 26

27 Retrofit Wall Switch Occupancy Sensor Technical Data Part No CCOSSDD1-P-VW Description The Diversa occupancy sensors use PIR and ADI-Voice technologies to determine the presence of people and perform the control actions when occupancy (or vacancy) is detected. The CCOS Series of sensors are designed replace a low voltage wall switch giving a 180 coverage pattern The low voltage edition of this sensor gives the capability of operating and controlling the CCP-PP20-D Power Pack and/or diode pulse relays. Direct replacement for WR Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com Specification Inputs 24 VAC +/-25% Class 2 Low Voltage Source 60Hz Use #18WG wire Outputs Diode Pulse : Each output is capable of driving up to one Diode Pulse relays. Power consumption 9.5 ma Standard Approvals FCC Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 14 F to 140 F (-10 C to 60 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) Low temp and high humidity option [-L] products: PCB conformal coated for resistance to damp environments and operation to -40 C/F. Features Wall Switch occupancy sensor provides 180 coverage to maximize the sensor area. The dual-tech sensor utilizes ADI-Voice Technology, which has advanced digital signal processing for accurate detection of human speech. A Self-adapting mode can be set to use Passive Infrared (PIR) & Accurate Detection Intelligence (ADI) Voice technologies to automatically track occupancy tendencies for continuous maximizing of energy savings. Smart Sensing allows for an immediate return to occupied mode in the event of a false off being triggered. Can be programmed by on-board DIP switches and dials or an IR Setting Unit for added convenience, especially during commissioning. cristalcontrols.com 27

28 Retrofit Wall Switch Occupancy Sensor Technical Data & Details Operation Line voltage sensors are powered by 24VAC from either the CCP-PP20-D Power Pack or a 24VAC tranformer. When in operation, the sensor will detect initial motion using PIR; once motion is detected the internal contact will close. The ADI- Voice is then activated to work alongside the PIR to detect occupancy. Dimensions & Mounting Mount in a standard gang box. Wiring Instructions The CCOS Series Low Voltage sensors are equipped with #22 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. Electrical Connections CCP-PP20-D 28

29 Retrofit Wall Switch Occupancy Sensor Details Sensors Settings (See page for Sensor Setting description item) 1. Programming - IR / Manual Setting 2. Detection (Dual or PIR Only) 3. Automatic Timeout 4. Smart Sensing 5. Vacancy Sensor 6. Photo Sensing (-P) 29

30 Retrofit Wall Switch Occupancy Sensor Details & Coverage Installation Mount the CCOSSDD1-P-VW sensor on the wall about 4' above floor level near the midline of the room so its PIR detection zones cover the room area and any obstructions are within range of the ADI-Voice detector. There should be no obstructions between the sensor and the room entrance. The ensures that the sensor's PIR lens will be activated when a person enters the room, wich will subsequently trigger the ADI-Voice. Installing in Offices f Sensor effective in obstructed spaces f ADI-Voice re-activation and Smart Sense prevents lights out condition Typical Office Installing in Washrooms f Sensor effective in partitioned spaces f ADI-Voice re-activation and Smart Sense prevents lignts out condition Standard Lens (S) f Optimal usage is to detect small motions such as hand movements f Designed for a mounting height of 7-15ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy Top View Side View Typical WashRooms *Application and Performance Specification Information Subject to Change without Notification 30

31 Retrofit Wall Switch Occupancy Sensor Installation Installation & Wiring Directions Installation Mounting of the device requires a standard box. Install by recessing the device into the standard gang box; lining up the mounting hole and securing it using the screws provided. Wiring The CCOSSDD1-P-VW Retrofit sensors are equipped with plug-in harness for easy installation. This hardness has #20 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. DIP Switches A bank of eight DIP switches and two rotating controls can be used to manually setup and configure the sensor. CCOSSDD1-P-VW DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) OFF 5* Photocell Inhibit** Disabled Enabled OFF 6* Photocell Control Inhibit 2 nd Pole Only Inhibit Both Poles OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 31

32 Low Voltage Wall Switch Occupancy Sensor Technical Data 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T *Plate not included Specification Inputs 24 VAC +/-25% Class 2 Low Voltage Source 60 Hz Use #18AWG wire Part No CCOSSDD2-P-VW CCOSSDD2-DPR-VW Description The Diversa occupancy sensors use PIR and ADI-Voice technologies to determine the presence of people and perform the control actions when occupancy (or vacancy) is detected. The CCOS Series of sensors are designed replace a low voltage wall switch giving a 180 coverage pattern. The low voltage edition of this sensor gives the capability of operating and controlling the WP- PP20-D Power Pack and/or diode pulse relays. Outputs Diode Pulse: Each output is capable of driving up to four Diode Pulse relays. 0-10V Dimming: Use to control up to 50 Ballasts, or 25mA sync of LED driver. Connections are polarity sensitive. Aux Relay: SPDT Form-C contact rated for 1A at 30VDC Power consumption 9.5 ma Standard 14.0 ma with Auxiliary Relay Approvals FCC Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 14 F to 140 F (-10 C to 60 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) Low temp and high humidity option [-L] products: PCB conformal coated for resistance to damp environments and operation to -40 C/F. Features Wall Switch occupancy sensor provides 180 coverage to maximize the sensor area. The dual-tech sensor utilizes ADI-Voice Technology, which has advanced digital signal processing for accurate detection of human speech. A Self-adapting mode can be set to use Passive Infrared (PIR) & Accurate Detection Intelligence (ADI) Voice technologies to automatically track occupancy tendencies for continuous maximizing of energy savings. Smart Sensing allows for an immediate return to occupied mode in the event of a false off being triggered. The photo sensor option is available to provide a 0-10VDC dimming ballast or 25mA sync for LED drivers output for Daylight Harvesting. F info@cristalcontrols.com Can be programmed by on-board DIP switches and dials or an IR Setting Unit for added convenience, especially during commissioning. cristalcontrols.com 32

33 Low Voltage Wall Switch Occupancy Sensor Technical Data & Details Operation Low voltage sensors are powered by 24VAC from either the CCP-PP20-D Power Pack or a 24VAC transformer. When in operation, the sensor will detect initial motion using PIR; once motion is detected the internal contact will close. The ADI- Voice is then activated to work alongside the PIR to detect occupancy. Dimensions & Mounting Mount in a standard gang box. Wiring Instructions The CCOS Series Low Voltage sensors are equipped with #22 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. Electrical Connections CCP-PP20-D 33

34 Low Voltage Wall Switch Occupancy Sensor Details Sensors Settings (See page for Sensor Setting description item) 1. Programming - IR / Manual Setting 2. Detection (Dual or PIR Only) 3. Automatic Timeout 4. Smart Sensing 5. Vacancy Sensor 6. Photo Sensing (-P) 7. Daylight Harvest Dimming (0-10V Output) (-D) 8. Multi-Level Switching (2-Pole w/o Photo Option) 9. Multi-Level Photo Sensing (2-Pole w/photo Option) 10. Sensor Link 34

35 Low Voltage Wall Switch Occupancy Sensor Details and Coverage Installation Mount the CCOS Series sensor on the wall about 4' above floor level near the midline of the room so its PIR detection zones cover the room area and any obstructions are within range of the ADI-Voice detector. There should be no obstructions between the sensor and the room entrance. The ensures that the sensor's PIR lens will be activated when a person enters the room, wich will subsequently trigger the ADI-Voice. Installing in Offices f Sensor effective in obstructed spaces f ADI-Voice re-activation and Smart Sense prevents lights out condition Typical Office Installing in Washrooms f Sensor effective in partitioned spaces f ADI-Voice re-activation and Smart Sense prevents lights out condition Standard Lens (S) f Optimal usage is to detect small motions such as hand movements f Designed for a mounting height of 4ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy Top View Side View Typical WashRooms 35

36 Low Voltage Wall Switch Occupancy Sensor Installation Installation & Wiring Directions Installation Mounting of the device requires a standard gang box. Install by recessing the device into the standard gang box; lining up the mounting holes and securing it using the screws provided. Wiring The CCOS Series Low Voltage sensors are equipped with plug-in harness for easy installation. This harness has #20 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. DIP Switches A bank of eight DIP switches and two rotating controls can be used to manually setup and configure the sensor. CCOS P - DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) OFF 5* Photocell Inhibit** Disabled Enabled OFF 6* Photocell Control Inhibit 2 nd Pole Only Inhibit Both Poles OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON 36

37 Low Voltage Wall Switch Occupancy Sensor Installation DIP Switches CCOS DPR - DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) OF 5* Photocell Inhibit** Photocell Disabled & Fixed Din Level Photocell Enabled & Auto Dim Level 6* Photocell Control Inhibit 2 nd Pole Only Inhibit Both Poles OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON OFF 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 37

38 Low Voltage Wall Mount Occupancy Sensor Technical Data Part No CCOWCDD2-R-N CCOWLDD2-R-N CCOWCDD2-DPR-N Description The Diversa occupancy sensors use PIR and ADI-Voice technologies to determine the presence of people and perform the control actions when occupancy (or vacancy) is detected. The CCOW Series of sensors are designed to surface mount on a wall giving either a 90 or 130 coverage pattern. Specification Inputs 24 VAC +/-25% Class 2 Low Voltage Source 60 Hz Use #18AWG wire The low voltage edition of this sensor gives the capability of operating and controlling the WP-PP20-D Power Pack and/or diode pulse relays Lavoisier, #135 Quebec, Quebec G1N 4L6 T F Outputs Diode Pulse: Each output is capable of driving up to four Diode Pulse relays. 0-10V Dimming: Use to control up to 50 Ballasts, or 25mA sync of LED driver. Aux Relay: SPDT Form-C contact rated for 1A at 30VDC Power consumption 9.5 ma Standard 14.0 ma with Auxiliary Relay Approvals FCC Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 14 F to 140 F (-10 C to 60 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) Features Wall mount occupancy sensor provides 90 or 130 coverage. Has the ability to rotate in both the horizontal and vertical axis to optimize the sensing area. The dual-tech sensor utilizes ADI-Voice Technology, which has advanced digital signal processing for accurate detection of human speech. A Self-adapting mode can be set to use Passive Infrared (PIR) & Accurate Detection Intelligence (ADI) Voice technologies to automatically track occupancy tendencies for continuous maximizing of energy savings. Smart Sensing allows for an immediate return to occupied mode in the event of a false off being triggered. The photo sensor option is available to provide a 0-10VDC dimming ballast or 25mA sync for LED drivers output for Daylight Harvesting. info@cristalcontrols.com Can be programmed by on-board DIP switches and dials or an IR Setting Unit for added convenience, especially during cristalcontrols.com commissioning. 38

39 Low Voltage Wall Mount Occupancy Sensor Technical Data & Details Operation Low voltage sensors are powered by 24VAC from either the CCP-PP20-D Power Pack or a 24VAC transformer. When in operation, the sensor will detect initial motion using PIR; once motion is detected the internal contact will close. The ADI- Voice is then activated to work alongside the PIR to detect occupancy. Dimensions & Mounting Mount in a octagon box. Wall Mount Ceiling Mount Wiring Instructions The CCOW Series Low Voltage sensors are equipped with #22 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. Electrical Connections CCP-PP20-D 39

40 Low Voltage Wall Mount Occupancy Sensor Details Sensors Settings (See page for Sensor Setting description item) 1. Programming - IR / Manual Setting 2. Detection (Dual or PIR Only) 3. Automatic Timeout 4. Smart Sensing 5. Vacancy Sensor 6. Photo Sensing (-P) 7. Daylight Harvest Dimming (0-10V Output) (-D) 8. Multi-Level Switching (2-Pole w/o Photo Option) 9. Multi-Level Photo Sensing (2-Pole w/photo Option) 10. Sensor Link 40

41 Low Voltage Wall Mount Occupancy Sensor Details & Coverage Installation Installing in Smaller Room (Corner Lens) f Locate the sensor in the corner, along the entrance door to prevent it from viewing out into the hallway. f The sensor can be rotated, allowing it to be pointed along the entrance door and slighly downwards. f Positioning the sensor in this manner ensures that an occupant move accross the longest detection beam upon entrance, utilizing the sensor's maximum PIR range. Typical Enclosed Office Corner Lens f Optimal usage is to detect small motions such as hand movements. f Designed for a mounting height of up to 7-15ft. f ADI-Voice can detect around corners that PIR cannot to maintain occupancy. Installing in Larger Room (Large Area Lens) f Place the sensor near the center of the wall that is adjacent to the entrance. f The sensor can be rotated, allowing it to be pointed along the entrance door and slighly downwards. f Positioning the sensor in this manner ensures that the beam does not reach outside the room without reducing sensitivity. Typical Classroom Large Area Lens f Optimal usage is to detect large motions such as walking. f Designed for a mounting height of 7-15ft. f ADI-Voice can detect around corners that PIR cannot to maintain occupancy. 41

42 Low Voltage Wall Mount Occupancy Sensor Installation Installation & Wiring Directions Installation Mounting of the device requires a 2 1/8" deep, octogonal junction box. Install by recessing the device into the o ctogonal box; lining up the mounting holes and securing it using the screws provided. Wiring The CCOW Series Low Voltage sensors are equipped with plug-in harness for easy installation. This harness has #20 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. DIP Switches A bank of eight DIP switches and two rotating controls can be used to manually setup and configure the sensor. CCOW R-N DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) OFF 5 Not Used N/A N/A OFF 6 Not Used N/A N/A OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 42

43 Line Voltage Wall Switch Occupancy Sensor Technical Data Part No CCOSSDU1-P-VW CCOSSDU2-P-VW CCVSSDU2-P-VW Description The Diversa occupancy sensors use PIR and ADI-Voice technologies to determine the presence of people and perform the control actions when occupancy (or vacancy) is detected. The CCOS Series of sensors are designed replace a low voltage wall switch giving a 180 coverage pattern *Plate not included Specification Power 120/277 VAC 60Hz Contact Ratings 120 VAC - 800W 277 VAC W Power consumption 400 ma Approvals Certified to UL 508, UL244A, CSA C22.2 #14 Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 32 F to 104 F (0 C to 40 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) Features Wall Switch occupancy sensor provides 180 coverage to maximize the sensor area. The dual-tech sensor utilizes ADI-Voice Technology, which has advanced digital signal processing for accurate detection of human speech. A Self-adapting mode can be set to use Passive Infrared (PIR) & Accurate Detection Intelligence (ADI) Voice technologies to automatically track occupancy tendencies for continuous maximizing of energy savings. Smart Sensing allows for an immediate return to occupied mode in the event of a false off being triggered. Can be programmed by on-board DIP switches and dials or an IR Setting Unit for added convenience, especially during commissioning Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 43

44 Line Voltage Wall Switch Occupancy Sensor Technical Data & Details Operation Line voltage sensors draw control power directly from the lighting circuit they are intended to control. When in operation the sensor will detect initial motion using PIR; once motion is detected, the internal contact will close. ADI-Voice is then activated to work alongside PIR to maintain the occupied condition as long as people are within the sensing range. Dimensions & Mounting Mount in a standard gang box. Wiring Instructions The CCOS Series Line Voltage sensors are equipped with #14 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. Electrical Connections CCOS**U*-*-* CCOS**U2*-*-* 44

45 Line Voltage Wall Switch Occupancy Sensor Details Sensors Settings (See page for Sensor Setting description item) 1. Programming - IR / Manual Setting 2. Detection (Dual or PIR Only) 3. Automatic Timeout 4. Smart Sensing 6. Photo Sensing (-P) 9. Multi-Level Photo Sensing (2-Pole w/photo Option) 45

46 Line Voltage Wall Switch Occupancy Sensor Details & Coverage Installation Mount the CCOS Series sensor on the wall about 4' above floor level near the midline of the room so its PIR detection zones cover the room area and any obstructions are within range of the ADI-Voice detector. There should be no obstructions between the sensor and the room entrance. The ensures that the sensor's PIR lens will be activated when a person enters the room, wich will subsequently trigger the ADI-Voice. Installing in Offices f Sensor effective in obstructed spaces f ADI-Voice re-activation and Smart Sense prevents lights out condition Typical Office Installing in Washrooms f Sensor effective in partitioned spaces f ADI-Voice re-activation and Smart Sense prevents lignts out condition Standard Lens (S) f Optimal usage is to detect small motions such as hand movements f Designed for a mounting height of 4ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy Top View Side View Typical WashRooms 46

47 Line Voltage Wall Switch Occupancy Sensor Installation Installation & Wiring Directions Installation Mounting of the device requires a standard gang box. Install by recessing the device into the standard gang box; lining up the mounting holes and securing it using the screws provided. CAUTION TURN POWER OFF AT THE CIRCUIT BREAKER BEFORE WORKING WITH OR NEAR HIGH VOLTAGE Wiring The CCOS Series Line Voltage sensors are equipped with #14 AWG stranded leads. Use appropriate sized wirenuts to connect the wires to the incoming load terminations; for installation with fieldinstalled conductors of 60ºC minimum rating. CCOS**U*-*-* CCOS**U2*-*-* 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com DIP Switches A bank of eight DIP switches and two rotating controls can be used to manually setup and configure the sensor. CCOS P - DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) ON 5* Photocell Inhibit** Disabled Enabled OFF 6* Photocell Control Inhibit 2 nd Pole Only Inhibit Both Poles OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON *Available in 2-Pole models (-2) only cristalcontrols.com 47

48 Line Voltage Wall Switch Occupancy Sensor, 347V Technical Data Part No CCOSSD31-P-VW CCOSSD32-P-VW Description The Diversa occupancy sensors use PIR and ADI-Voice technologies to determine the presence of people and perform the control actions when occupancy (or vacancy) is detected. The CCOS Series of sensors are designed replace a low voltage wall switch giving a 180 coverage pattern. 347 VAC. *Plate not included Specification Power 347 VAC 60Hz Contact Ratings 347 VAC W Power consumption 400 ma Approvals Certified to UL 508, UL244A, CSA C22.2 #14 Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 32 F to 104 F (0 C to 40 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) Low temp and high humidity option [-L] products: PCB conformal coated for resistance to damp environments and operation to -40 C/F. Indoor use only. Features Wall Switch occupancy sensor provides 180 coverage to maximize the sensor area. The dual-tech sensor utilizes ADI-Voice Technology, which has advanced digital signal processing for accurate detection of human speech. A Self-adapting mode can be set to use Passive Infrared (PIR) & Accurate Detection Intelligence (ADI) Voice technologies to automatically track occupancy tendencies for continuous maximizing of energy savings. Smart Sensing allows for an immediate return to occupied mode in the event of a false off being triggered. Can be programmed by on-board DIP switches and dials or an IR Setting Unit for added convenience, especially during commissioning Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 48

49 Line Voltage Wall Switch Occupancy Sensor, 347V Technical Data & Details Operation Line voltage sensors draw control power directly from the lighting circuit they are intended to control. When in operation the sensor will detect initial motion using PIR; once motion is detected, the internal contact will close. ADI-Voice is then activated to work alongside PIR to maintain the occupied condition as long as people are within the sensing range. Dimensions & Mounting Mount in a standard gang box. Wiring Instructions The CCOS Series Line Voltage sensors are equipped with #14 AWG leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. Electrical Connections CCOSSD3*-*-* CCOSSD32*-*-* 49

50 Line Voltage Wall Switch Occupancy Sensor, 347V Details Sensors Settings (See page for Sensor Setting description item) 1. Programming - IR / Manual Setting 2. Detection (Dual or PIR Only) 3. Automatic Timeout 4. Smart Sensing 6. Photo Sensing (-P) 9. Multi-Level Photo Sensing (2-Pole w/photo Option) 50

51 Line Voltage Wall Switch Occupancy Sensor, 347V Details & Coverage Installation Mount the CCOS Series sensor on the wall about 4' above floor level near the midline of the room so its PIR detection zones cover the room area and any obstructions are within range of the ADI-Voice detector. There should be no obstructions between the sensor and the room entrance. The ensures that the sensor's PIR lens will be activated when a person enters the room, wich will subsequently trigger the ADI-Voice. Installing in Offices f Sensor effective in obstructed spaces f Voice sound re-activation prevents lights out condition Typical Office Installing in Washrooms f Sensor effective in partitioned spaces f Voice sound re-activation prevents lignts out condition Standard Lens (S) f Optimal usage is to detect small motions such as hand movements f Designed for a mounting height of 4ft f ADI-Voice can detect around corners that PIR cannot to maintain occupancy Top View Side View Typical WashRooms 51

52 Line Voltage Wall Switch Occupancy Sensor, 347V Installation Installation & Wiring Directions Installation Mounting of the device requires a standard gang box. Install by recessing the device into the standard gang box; lining up the mounting holes and securing it using the screws provided. CAUTION TURN POWER OFF AT THE CIRCUIT BREAKER BEFORE WORKING WITH OR NEAR HIGH VOLTAGE Wiring The CCOS Series Line Voltage sensors are equipped with #14 AWG stranded leads. Use appropriate sized wirenuts to connect the wires to the incoming load terminations; for installation with fieldinstalled conductors of 60ºC minimum rating. CCOSSD3*-*-* CCOSSD32*-*-* 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com DIP Switches A bank of eight DIP switches and two rotating controls can be used to manually setup and configure the sensor. CCOS P - DIP # Function On Off Default 1 Voice Detection Disabled Enabled OFF 2 Motion Detection Sensivity High Normal OFF 3 Detection LED Disabled Enabled OFF 4 Auto or Manual ON Occupancy (Auto-ON) Vacancy (Manual ON) ON 5* Photocell Inhibit** Disabled Enabled OFF 6* Photocell Control Inhibit 2 nd Pole Only Inhibit Both Poles OFF 7 Manual Override Button Disabled Enabled OFF 8 Settings Input IR Handheld (CCIR-3110) Manual Dips/Dials ON *Available in 2-Pole models (-2) only cristalcontrols.com 52

53 1-Pole Power Pack ( ) Technical Data Part No CCP-PP20-D 1-Pole 120/277VAC Features Designed for use with Diversa occupancy sensors and Diode Pulse relays. Single pole 120/277 VAC Specification Load Voltage 120/277 VAC 60 Hz Switched Load 120/277 VAC See Table for contact rating Use #14 AWG Wire Inputs Diode Pulse #14AWG wire Secondary Power Source 24 VAC, 150 ma #14AWG wire Approvals Certified to CAN/CSA Std. C22.2 No. 14 Conforms to UL 508 Standard Title 24 FCC Plenum Rated Class 2 Rating Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 14 F to 140 F (-10 C to 60 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 53

54 1-Pole Power Pack ( ) Technical Data & Details Operation The CCP-PP20-D Power Pack work in conjunction with the Diversa Low Voltage Sensors by providing power to the sensors and receiving on/off commands from the sensor. Contact Load Rating Voltage General Tungsten Standard Ballast Electronic Ballast 120V 20A 20A 20A 16A 277V 20A 20A 20A 16A All Power Packs provide a 24 VAC secondary source for use with the Low Voltage Diversa Sensors and other Diode Pulse devices. All switches or loads required to be supported by the sensor must be included in the loading capacity of the Power Pack. Wiring Directions Voltage Maximum Load Per Input Max# of linked sensors 24VAC 12 Typical Low Voltage Loads Device Part# Current (ma) Ceiling Mounted Sensor Wall Switch Sensor Wall Mount Sensor CCOR/CCVR CCOS/CCVS CCOW/CCVW 9,5mA Standard 14,0mA w/aux Relay Diode Pulse Switch WR mA Wiring Terminating wire shall be a minimum of #22 AWG for control power connections and shall be suitably sized to handle the load ratings below. Electrical Connections CCP-PP20-D 54

55 1-Pole Power Pack ( ) Details Dimensions & Mounting The power pack shall be mounted inside an electrical junction box or panel with a ½ threaded nipple. CCP-PP20-D * Application and Performance Specification Information Subject to Change without Notification 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 55

56 1-Pole Power Pack (347-1) Technical Data Part No CCP-PP D 1-Pole VAC Features Designed for use with Diversa occupancy sensors and Diode Pulse relays. Single pole 347 VAC Specification Load Voltage 347 VAC 60 Hz Switched Load 347 VAC See Table for contact rating Use #14 AWG Wire Inputs Diode Pulse #14AWG wire Secondary Power Source 24 VAC, 150 ma #14AWG wire Approvals Certified to CAN/CSA Std. C22.2 No. 14 Conforms to UL 508 Standard Title 24 FCC Plenum Rated Class 2 Rating Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 14 F to 140 F (-10 C to 60 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 56

57 1-Pole Power Pack (347-1) Technical Data & Details Operation The CCP-PP D Power Pack work in conjunction with the Diversa Low Voltage Sensors by providing power to the sensors and receiving on/off commands from the sensor. Contact Load Rating Voltage General Tungsten Standard Ballast Electronic Ballast 347V 20A 20A 20A 16A All Power Packs provide a 24 VAC secondary source for use with the Low Voltage Diversa Sensors and other Diode Pulse devices. All switches or loads required to be supported by the sensor must be included in the loading capacity of the Power Pack. Voltage Maximum Load Per Input Max# of linked sensors 24VAC 12 Typical Low Voltage Loads Device Part# Current (ma) Ceiling Mounted Sensor Wall Switch Sensor Wall Mount Sensor CCOR/CCVR CCOS/CCVS CCOW/CCVW 9,5mA Standard 14,0mA w/aux Relay Diode Pulse Switch WR mA Installation & Wiring Directions Installation The power pack shall be mounted inside an electrical junction box or panel with a ½ threaded nipple. CAUTION TURN POWER OFF AT THE CIRCUIT BREAKER BEFORE WORKING WITH OR NEAR HIGH VOLTAGE Wiring The power packs are equipped with #14 AWG stranded leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. For installation with field-installed conductors of 60ºC minimum rating. 57

58 1-Pole Power Pack (347-1) Details Electrical Connections CCP-PP D Dimensions & Mounting The power pack shall be mounted inside an electrical junction box or panel with a ½ threaded nipple. CCP-PP D * Application and Performance Specification Information Subject to Change without Notification 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 58

59 2-Pole Power Pack ( ) Technical Data Part No CCP-PP20-2P-D 2-Pole 120/277VAC Features Designed for use with Diversa occupancy sensors and Diode Pulse relays. 2 pole 120/277 Specification Load Voltage 120/277 VAC 60 Hz Switched Load 120/277 VAC 2-Pole Independent Switching See Table for contact rating Use #14 AWG Wire Inputs Diode Pulse #18AWG wire Output Power Source 24 VAC, 150 ma #14AWG wire Approvals Certified to CAN/CSA Std. C22.2 No. 14 Conforms to UL 508 Standard FCC Title 24 Plenum Rated Class 2 Rating Environment Indoors, stationary, non-vibrating, non-corrosive atmosphere and non-condensing humidity Ambient Operating Temperature : 14 F to 140 F (-10 C to 60 C) Storage Temperature : -14 F to 140 F (-25 C to 60 C) 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 59

60 2-Pole Power Pack ( ) Technical Data & Details Operation The CCP-PP20-2P-D Power Pack work in conjunction with the Diversa Low Voltage Sensors by providing power to the sensors and receiving on/off commands from the sensor. Contact Load Rating Voltage General Tungsten Standard Ballast Electronic Ballast 120V 20A 20A 20A 16A 277V 20A 20A 20A 16A All Power Packs provide a 24 VAC secondary source for use with the Low Voltage Diversa Sensors and other Diode Pulse devices. All switches or loads required to be supported by the sensor must be included in the loading capacity of the Power Pack. Voltage Maximum Load Per Input Max# of linked sensors 24V 12 Typical Low Voltage Loads Device Part# Current (ma) Ceiling Mounted Sensor Wall Switch Sensor Wall Mount Sensor CCOR/CCVR CCOS/CCVS CCOW/CCVW 9,5mA Standard 14,0mA w/aux Relay Diode Pulse Switch WR mA Installation & Wiring Directions Installation The power pack shall be mounted inside an electrical junction box or panel with a ½ threaded nipple. CAUTION TURN POWER OFF AT THE CIRCUIT BREAKER BEFORE WORKING WITH OR NEAR HIGH VOLTAGE Wiring The power packs are equipped with #14 AWG stranded leads. Use appropriate sized wire-nuts to connect the wires to the incoming load terminations. For installation with field-installed conductors of 60ºC minimum rating. 60

61 2-Pole Power Pack ( ) Details Electrical Connections CCP-PP20-2P-D Dimensions & Mounting The power pack shall be mounted inside an electrical junction box or panel with a ½ threaded nipple. CCP-PP20-D * Application and Performance Specification Information Subject to Change without Notification 2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F info@cristalcontrols.com cristalcontrols.com 61