Light Sensor Module (LSM01)
|
|
- Sherman Cooper
- 5 years ago
- Views:
Transcription
1 Light Sensor Module (LSM01) LSM01 PCB May mount in Comfort CPU or SEP K1 LSM01 VR1 R2 U1 NC COM NO TO SENSOR TO MAIN + IN S- O/P GND 12V GND Photocell (Externally Mounted in transparent box or behind PIR lens ) 10k -12K Resistor - may be soldered into the PCB in R2 position eg. To Zone 13 Input Type 24. Introduction The Comfort Light Sensor Module (LSM01) is used to provide indication to a Comfort system when the light level has crossed an adjustable threshold level. This may be used within conditional responses or used directly to trigger Responses based on a selected light level. The Light Sensor is a Light Dependent Resistor (LDR or photocell) which reduces its resistance when the light intensity increases. This module may also be used for Temperature and Water Applications by using a different sensor. 1
2 Physical Dimensions: 88 x 53 mm Mounting Holes: 4 5 mm from each corner Connections/Components JP1 - Connection to Light Sensor. JP2-12V/GND supply from Comfort JP3 - Light Sensor open-collector output to Comfort Input JP4 - Relay Output (Not Used) D2 - LED indicates when the Light Sensor Output is triggered. 4 x 25mm metal mounting posts and 3mm screws. Loose Photocell and 10k ohm resistor. Installation & Adjustment 1. Mount the PCB in the Main Comfort CPU using the screws and pillars provided. 2. Connect the 12V and GND from Comfort to JP2 (12V/GND). Light ON DARK Light OFF DAYLIGHT VR1 3. Connect two wires from JP3 (O/P and GND) to one of Comfort s Inputs, taking care not to ensure polarity is correct, i.e. O/P to Comfort Input, GND to COM (common centre pin) on Comfort. The LSM output is open-collector, which means that when it is off (low light level), the output is an open circuit, and when it is ON (high light level), the output is shorted to ground (0V). 4. Connect the Light Sensor (photocell) to JP1 between IN and +. Connect the supplied resistor between IN and S-. This resistor matches the resistance of the Light Sensor at normal light conditions. The LSM may also be configured with the matching resistor fixed on the PCB (R2 position). The Light sensor may be located a long distance away from the LSM. Check the wire resistance does not exceed 100 ohms. 5. Do this adjustment at dusk OR cover the Light sensor to approximate dusk. The indicator LED (D2) should switch ON. If it is not, turn the trimmer VR1 clockwise (CW) until the LED JUST turns ON. Note the position of the trimmer wiper. 2
3 6. Place the light sensor where the ambient light conditions are brighter than the required threshold light level. The LED should be OFF. If not, adjust VR1 clockwise (CW) until the LED turns on. Note the position of the trimmer wiper. Now Adjust the trimmer so that it is between the two positions. The switching point is subject to hysteresis, i.e. when the LED turns on, the light level has to go some way below the point at which it turned on, in order to turn off. This is so that at the threshold light level, the output does not oscillate between on and off. 7. Test the switching in a real situation. 8. If you wish, the resistor may be soldered into position R2 on the PCB. 9. You can fit the photocell in the doorphone or within an external pir or camera. If siting within a camera or doorphone use the spare cores from the 8-core cable to remotely site the LSM photocell. Drill a 6mm hole underneath the camera, apply a blob of hot-melt glue inside the hole and push the photocell into the glue from the inside allowing a bead type lens to protrude slightly from the underside of the plastic. Programming (Default: Zone 13) ZONE TYPE: Zone Type 24 (normally closed). Sensitivity change to 850 ms 1. Program the Input connected to the LSM as Zone Type 24 (Normally Closed Switch). The Zone Settings Menu is in Engineer Menu 1. Some Comfort default response use the light sensor attached to zone 13. Response 126 (external X10 L1 ON for 3 mins) and Response 231 (Hall light X10 A1 ON during entry alert). 2. Program up to 4 words to describe the zone from the wordlist eg. Light Sensor Control. 3. Set Zone Type 24 Sensitivity to 850 ms (default = 100 ms) to that the zone state change has to be 850 ms minimum to be accepted. This reduces the chances of multiple transitions arounf the threshold light level 4. When the LSM changes state at dusk level the output turns OFF, the Comfort input will detect an OPEN condition, which can trigger the ON Response for Dusk applications. When the LSM output changes state at DAWN, the Comfort input will detect an CLOSED condition, and will trigger the OFF Response 5. Program the ON or OFF Response or both to perform the actions required. If the light level is to be used for checking a condition within other responses, use the actions (79,13,12) in front of your response, this means check zone 13 (light level) and exit if zero (light). The light sensor will return a value of 1 on the zone when darkness is detected. 6. A Timer Delay is recommended in order to counter the effect of multiple switching of the sensor at around dusk or dawn despite the hysteresis provided in the circuit. A sample program is found in the next section 7. To test, select Security Check (Keypad F+3, 2 or User Menu 3,4,2). In Security Check Mode, Comfort announces all zones which turn on. When the 3
4 Light Sensor Output turns on, Comfort should announce it, Light sensor Control 8. You may program Comfort to announce the zone when triggered (not in Security Check) by using Action 1 (Announce Zone) in a Response assigned to the zone ON response. To get Comfort to announce when the Light sensor turns off, Use Action 1 in a Response assigned to the OFF Response. Program Location 1689 with 229, which is the word for OFF. For example, you can set the Zone ON and OFF Response to 59, which has Action 1 to announce ON and OFF. See back page for troubleshooting. Light Sensor/Resistor The Light sensor and Resistor should be matched, especially if the light sensor is not supplied by Cytech Technology A suiitable Light Dependant Resistor (reference Farnell part number ) specifications are as follow: * Resistor element type:light Dependent * Wavelength, spectral response peak:650nm * Voltage rating, DC:100V dc * Case style:radial * Depth, external:4.6mm * Diameter, lead:0.5mm * Length / Height, external:3.2mm * Length, lead:34mm * Power dissipation:50mw * lux A max:100kr * lux A min:50kr * Resistance, dark:5mr * Temperature, operating max:60 C * Temperature, operating min:-30 C * Wavelength, peak:550nm * Width, external:5.3mm At the required light level (ie dusk or dawn) measure the LDR resistance of the component when not connected to the LSM with a multimeter. This resistance should be matched to the vallue of external series resistor (in a range +/- 50%) If there is excessive switching of light sensor at the threshold light level, use a higher series resistor - tihis will reduce the sensitivity of the LSM to light. The Timer delay as described in the next section can also be used 4
5 Sample Response with Timer Delay This response uses 1 timer. The ON response will immediately do the required action without delay, when dark. The OFF Response activated when the sensor goes off, or when bright will start a timer, at the end of which the zone is checked, and if still Off (bright) will do the required actions. The timer delay is set at 180 seconds or 3 minutes. This can be changed as required Zone On Response: (Liight sensor detects dark) Do LightsOn [Lights On] Zone Off Response (Light sensor detects light) Do LightSensorOffDe [Light Sensor Off Delayed Response] After 180 Seconds Using LightSensorTMR Light Sensor Off Delayed Response (after Timer delay) If Input Zone13 = 0 Then Do Lights Off [Lights Off] End If 5
6 TROUBLESHOOTING 6 ELEMENTS WHICH GO TO MAKE UP 5 AUTOMATED LIGHTING RESPONSE BASED ON MOVEMENT AND LUX LSM01 ZONE 13 CHECK RESPONSE 4 ZONE ON 3 ACTION OUTPUT OR X10 SIGNAL - SWICHES LIGHT 1 MOVEMENT ZONE 2 If your design doesn t do what you expect it to do, you will need to troubleshoot it. The only effective way to do this is to break the chain of events down into logical stages and test each one individually. The above diagram shows the elements in a typical movement / LUX Level dependent scenario. Faults are usually caused by a simple mistake that has been made along the way. Here is the method to solve the above setup. It assumes that the function is being tested under simulated darkness Conditions. Either the sensor has been darkened with a covering or the LSM01 threshold sensitivity has been adjusted to simulate dark light conditions using VR1 pot. 1. Check the light operates manually using other means such as Home Control Menu or if X10 based, use Radio transmitter HR10 with TM12U. 2/3. Check the movement detector is programmed correctly with the correct zone type and response and working. Walk Test the sensor use menu F3/ Check the response is entered correctly using (Eng Menu 3,6). 5. Check the light sensor zone is programmed correctly with zone type 24 and that it the zone announces using Walk Test F+3, Check that the LSM01 is showing the red LED(D2) meaning it is Dark, if not turn the pot VR1 clockwise until it just illuminates. Remove the LSM01 output from the Light Sensor Zone Input by unplugging the terminal block. In this condition Comfort thinks it is dark, now test the calling response again by walking in front of the PIR. IMPORTANT: Responses CANNOT Operate while the system is in Security Check Mode (F3, 2). 6
7 Acknowledgement Portions of this manual were contributed by Comfort Home Controls (Iscam Systems Ltd) in 2001 History Document Title Light Sensor Module Document Revision Date 10 March 2007 Added Light sensor resistor matching section and Timer Response Rev Initial Release 2002 Please download the latest version of this manual from as the printed manual supplied with the product may not be the latest 7
ARROWHEAD ALARM PRODUCTS Ltd. 344b Rosedale Rd, Albany, Auckland. Ph Fax v1.0
ARROWHEAD ALARM PRODUCTS Ltd. 344b Rosedale Rd, Albany, Auckland. Ph. 09 414 0085 Fax. 09 414 0088 www.aap.co.nz v1.0 Zone Trouble Shooting (single EOL) = = = = RED, RED, RED, GOLD. = YELLOW, VIOLET, RED,
More informationModels NFPA 1221-A, NFPA 1221-B Public Safety DAS Annunciator Panel. Revision E 61117
Models NFPA 1221-A, NFPA 1221-B Public Safety DAS Annunciator Panel Revision E 61117 CAUTION: (Read This First) This panel has been designed to make it nearly bullet proof to mistakes made when wiring
More informationWD-CS. Water leak detection cable. Technical Overview. Features. Page 1. Data Sheet Ref: Issue: 5.1.
Data Sheet Ref: 90501085 WD-CS Water leak detection cable Technical Overview The WD-CS range of cable sensors are typically used to detect water leaks usually under floors, and are used in conjunction
More informationPublic Safety DAS Annunciator Panel
Public Safety DAS Annunciator Panel 120 VAC Models: 1221-A, 1221-B, 1221-C Revision D 91117 48 VDC Models: 1221-A-48, 1221-B-48, 1221-C-48 24 VDC Models: 1221A-24, 1221-B-24, 1221-C-24 CAUTION: (Read This
More information360º Surface Mount Ceiling PIR Light Controller
360º Surface Mount Ceiling PIR Light Controller Model: PDRS1500 Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference
More informationLUX Hardwired - Installation Notes
Ness LUX wired PIR with Nightlight Quad element pyro sensor 15m x 15m wide angle coverage Look down Creep Zone Selectable Standard and Pet Aware modes Adjustable sensor mask for No Creep and Pet modes
More informationD-Tect 2 GJD300 Quad PIR Movement Detector
D-Tect GJD0 Quad PIR Movement Detector Package Contents 3. Package Contains: x D-Tect x Drilling template for fixing holes x Allen Key 3 x 3.75mm wall plugs 3 x 3.75mm screws x Spare Sliding Curtains x
More informationComfort Applications Manual
Comfort Applications Manual Comfort This page intentionally left blank. Security/Automation Integration SECURITY / AUTOMATION INTEGRATION. Automatically Switch off appliances when system is armed. Programming
More informationD-TECT Introduction. Connecting the Unit. Quick Installation. Multi Beam Alignment & Masking. Mounting the Unit
D-TECT 2 GJD300 Quad PIR Movement Detector Package Contents Package Contains: 1 x D-Tect 2 1 x Drilling template for fixing holes 3 x 31.75mm wall plugs 3 x 31.75mm screws 2 x Spare Sliding Curtains 2
More informationChicken Door User Manual
Chicken Door User Manual Introduction This chicken door incorporates a linear actuator to horizontally slide the existing door of the hen house. The door opens just after dawn and closes just after dusk
More informationFire Extinguishing Control Panel INSTRUCTION MANUAL. Revision 8/ Instruction Manual Page 1 Revision 8/01.17 of 63
Fire Extinguishing Control Panel FS5200Е INSTRUCTION MANUAL Revision 8/01.17 Instruction Manual Page 1 1. 2. 3. 4. 4.1. 4.2. 4.2.1. 4.2.2. 4.2.3. 4.2.4. 4.2.5. 4.2.6. 4.2.7. 4.2.8. 4.2.9. 4.2.10. 4.2.11.
More informationSTROBE / SOUNDER INTERFACE
STROBE / SOUNDER INTERFACE INSTALLATION & CONFIGURATION MANUAL 21/10/2010 Rev: 2.00 DOC-01-002 ECN10-183 Documentation Feedback Your feedback helps us keep our documentation up to date and accurate. If
More informationDETECTOR TRANSMITTER INSTALLATION & OPERATING. Cat No. TLTX2000B INSTRUCTIONS
DETECTOR TRANSMITTER Cat No. TLTX2000B INSTALLATION & OPERATING INSTRUCTIONS 1 Introduction The TLTX2000B Controller Transmitter is part of the Timeguard range of PIR products which communicate by radio
More informationQA16 Addressable System
QA16 Addressable System Operating Manual HORING LIH INDUSTRIAL CO., LTD. www.horinglih.com QA16 System Characteristics Each loop can connect with 250 devices. Easy system programming through PC to panel.
More informationCarbon Monoxide Transmitter
Introduction The CO Transmitter uses an electrochemical sensor to monitor the carbon monoxide level and outputs a field-selectable 4-20 ma or voltage signal. The voltage signal may also be set to 0-5 or
More informationElite. GJD022 /GJD023 35m External PIR. Multi Beam Lens Data
Elite GJD022 /GJD023 35m External PIR Multi Beam Lens Data The GJD multifunction lens fitted to the GJD Elite detector produces 9 long range beams and 9 medium to short range curtain beams. Movement across
More informationQUICKFIT INSTALL HOOK-UP SHEET FOR ESL KIT REV 1.17 OP
QUICKFIT INSTALL HOOK-UP SHEET FOR ESL KIT REV 1.17 OP PROGRAMMING STARTS Entering Installer mode If you want to get into program mode press followed by your installer code, default set to 000000
More information64.7 Ø85. (1) Sensor inset (2) Lens pluggable. (3) Protection cover (covers the high-voltage terminals). (4) Ceiling (drill hole Ø70mm).
Flush Mount PIR Motion Sensor PIR 1-10V Dimming with Remote Control Mechanical Structure 70mm 64.7 4 56 68.1 73.3 Ø85 3 (1) Sensor inset (2) Lens pluggable Infrared receiver 1 Photocell LED indicator (3)
More informationOperating instructions
MA00929301 09/2015 Operating instructions ED10429002 ESYLUX GmbH An der Strusbek 40 22926 Ahrensburg Germany info@esylux.com www.esylux.com 1 Table of contents 1 Using the manual 8 2 Safety instructions
More informationPSC-BL-I-FM-DC0(-BLE) Bi-level Dimming PIR Sensor
TECHNICAL SPECIFICATIONS PSC-BL-I-FM-DC0(-BLE) Bi-level Dimming PIR Sensor Overview Quad Element PIR sensor 0-10V configurable output: set to 0% (OFF)*, 10%, 25% or 50% dimming Photocell for ambient light
More information360º FLUSH MOUNT CEILING PIR LIGHT CONTROLLER INSTALLATION & OPERATING. Cat No. SLFM360 INSTRUCTIONS
360º FLUSH MOUNT CEILING PIR LIGHT CONTROLLER Cat No. SLFM360 INSTALLATION & OPERATING INSTRUCTIONS 1 Introduction The SLFM360 utilises passive infrared technology to detect heat radiation of moving human
More informationFor assistance with the product please contact: HELPLINE. For a product brochure please contact:
For assistance with the product please contact: HELPLINE 020 8450 0515 or email helpline@timeguard.com For a product brochure please contact: Timeguard Limited. Victory Park, 400 Edgware Road, London NW2
More informationInstallation & Programming Guide
Alert Version 8 Zone Control Arrowhead Alarm Products Ltd Installation & Programming Guide Proudly Designed and Manufactured in New Zealand Arrowhead Alarm Products Ltd PHONE: (09) 579 7506 FAX: (09) 579
More informationFR-4000 & FR-8000 Fire Alarm Monitor Installation Manual
FR-4000 & FR-8000 Fire Alarm Monitor Installation Manual Table of Contents Introduction 1 System Components 2 Wiring Block Diagram 3 Connection Diagram for One Sensor 4 Connection Diagram for Multiple
More informationrvm4c Installation Guide Remote Video Module
rvm4c EN Installation Guide Remote Video Module rvm4c Installation Guide Installation Diagrams EN 2 Installation Diagrams for the Transmitting Unit rvm4c Installation Guide Basic Hardware Installation
More informationGAS SUPRESSION CONTROL PANEL:
GAS SUPRESSION CONTROL PANEL: MODEL NAME: COMPANY: DELTA 437/2, Main Road, Mandwali Fazalpur, Delhi-110092 Page 1 ABOUT THE PRODUCT ASES is very proud of to introduce DELTA the completely digital microprocessor
More informationMovement Detector GJD 300
Movement Detector GJD 300 Installation & Set Up Guide Introduction A CCTV event trigger utilising two independent passive infrared detectors combined in a T05 package. Both sensors have to trigger before
More informationCeiling Microwave presence detector - DALI / DSI 12-24V AC/DC. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MWS6-DD-LV Product Guide Ceiling Microwave presence detector - DALI / DSI 12-24V AC/DC Overview The MWS6-DD-LV microwave presence detector provides automatic control of lighting loads with optional manual
More informationZerio Plus EDA-D6000 Radio Combined Heat Detector and Sounder Installation Instructions
Zerio Plus EDA-D6000 Radio Combined Heat Detector and Sounder Installation Instructions EN54-3:2001+A1:2002+A2:2006 EN54-5:2000+A1:2002 EN54-25:2008 0359 Electro Detectors Ltd. Electro House Edinburgh
More information2 x CR123A Lithium batteries. White night-light LED. Blue alarm LED - also glows behind the lens. Ambient light sensor behind lens.
15m x 15m wide angle coverage Look down Creep Zone White LED motion activated night-light Adjustable Pulse Count Adjustable Range High R.F. and E.S.D. immunity High white light immunity SAWR stabilised
More informationEnglish. Series. Installation and Use Manual
English Series FOSTER Installation and Use Manual FOSTER Rev.13 03/2015 MITECH srl reserves the right to change the information in this document without warning. Index Anti-intrusion barrier 3 Main components
More informationAutomatic Night Lamp Circuit Diagram Using Ldr And Triac
Automatic Night Lamp Circuit Diagram Using Ldr And Triac During day time the LDR has low resistance and keeps the pin 12 of the IC1 high, That means the high output drives the triac to switch on the lamp
More informationDanfoss gas detection units
Data sheet Danfoss gas detection units Types GD Premium, Premium+, Premium Duplex, Premium Remote, Premium Flex and Premium Uptime The Premium line gas detection units are used for monitoring and warning
More informationRectifier RC-series. Manual RC-series English MA doc. Manual Wall and 19 English
Rectifier RC-series Manual RC-series English Manual Wall and 19 English Presentation The RC-series is a rectifier for either directly powering the load or for use together with batteries. It is designed
More informationGeneral Purpose IO Technical Manual
General Purpose IO Technical Manual Revision 1.06 8 November 2013 Pakton Technologies PAE222 GPIO Manual.docx Page 1 of 21 Revision 1.06 Last updated 8/11/2013 Table of Contents INTRODUCTION...3 Scope
More informationVAP304 PRO INSTALLATION & OPERATION MANUAL
VAP304 PRO INSTALLATION & OPERATION MANUAL Panic Fire Duress Program Bypass Report Chime Test Memory B A D C Program Chime Panic Duress Exit Fire Report Bypass Memory Test Reset Password Exit Reset Password
More informationDuct and Rough Service Carbon Monoxide Sensor
Product Identification and Overview Duct and Rough Service Carbon Monoxide Sensor BAPI s Carbon Monoxide Sensor offers enhanced electrochemical sensing with outstanding accuracy at low concentrations.
More informationChallenger Version 8 Programming Relays.
Challenger Version 8 This document provides details of the programming requirements for activating relays on the Challenger system. The following are some of the applications that Challenger Relays may
More informationFor assistance with the product please contact: HELPLINE. For a product brochure please contact:
For assistance with the product please contact: HELPLINE 020 8450 0515 or email helpline@timeguard.com For a product brochure please contact: Timeguard Limited. Victory Park, 400 Edgware Road, London NW2
More informationPart 1: Playing with Electricity
Foreword by Joe Grand... Acknowledgments... xix xxi Introduction xxiii About This Book...xxiv Who Should Read This Book...xxiv How to Read This Book....xxiv What s in This Book?....xxv Your Electronics
More informationDOLKPL1KB DOLKPS1KB DOLKSF1KB
DOLKPL1KB DOLKPS1KB DOLKSF1KB USER MANUAL INSTRUCTIONAL VIDEO 1] Connection Terminals 2] Basic Wiring Example 3] Quick Start Guide 4] Programming Guide 5] Specifications 1 Connection Terminals The DOLKPS1KB/DOLKPS1KB/DOLKSF1KB
More informationPIR/INT & PIR/INT-D. Batten mount PIR detectors. Product Guide. Overview. Features
Product Guide PIR/INT & PIR/INT-D Batten mount PIR detectors Overview The PIR/INT & PIR/INT-D miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional
More informationF PC and AO OUTPUT BOARDS INSTRUCTION MANUAL. Blue-White. Industries, Ltd.
F-2000 PC and AO OUTPUT BOARDS INSTRUCTION MANUAL Blue-White R Industries, Ltd. 500 Business Drive Huntington Beach, CA 92649 USA Phone: 714-89-8529 FAX: 714-894-9492 E mail: sales@blue-white.com or techsupport@blue-white.com
More informationFIRERAY 5000 range USER GUIDE
FIRERAY 5000 range USER GUIDE 0044-003-04 IMPORTANT PLEASE NOTE: The beam path MUST be kept clear of obstructions at all times! Failure to comply may result in the Detector initiating a Fire or Fault signal.
More informationGARDTEC 580. Installation Instructions
GARDTEC 5 0 0 S E R I E S GARDTEC 580 Installation Instructions Contents Introduction 1 Planning the Control Panel Location 2 Installation 2 Cable Entries 3 Mains Supply Connection 4 Terminal Block Connections
More informationDetailed Instructions
Introduction Timer is a versatile, rugged, and easy to use indoor / outdoor appliance timer. It can be used with lights and other household appliances that require regular on-off cycles and has two main
More informationE Wired Intruder Detector
E93.97 Wired Intruder Detector JAN 3, 05 Description The E93.97 is very suitable for applications in wired intruder detectors. It works with all popular conventional analog PIR detectors. No false alarms
More informationDCA4. Digitally controlled Audio Matrix. Current Thinking. Product Specification March Document Number DDC DCA ACS
DCA4 Digitally controlled Audio Matrix Product Specification March 2002 Current Thinking Document Number DDC DCA 7001 01 ACS Introduction Voice Alarm (VA) systems are the quickest way to evacuate the public
More informationMOBILE CALL GSM Alarm System User s Manual
MOBILE CALL GSM Alarm System User s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. Contents Function Introduction (3) Alarm Host Diagram
More informationOperating instructions 2-channel code lock. Item No
Operating instructions 2-channel code lock Item No. 1560346 Table of contents Page 1. Introduction...4 2. Explanation of symbols...4 3. Intended use...5 4. Delivery content...5 5. Safety instructions...6
More informationELT-KLED EliteSuite LED Keypad Installation Manual
ELT-KLED EliteSuite LED Keypad Installation Manual ELT-KLED EliteSuite Installation Manual PUBLICATION INFORMATION First Publication Draft Document Release Only Updated fire zone information Second Publication
More informationHigh bay PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
EBDSPIR-HB-DD Product Guide High bay PIR presence detector DALI / DSI dimming Overview The EBDSPIR-HB-DD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional
More information60W Multi PIR Bulkhead
60W Multi PIR Bulkhead Model: MLB98 Black Installation & Operating Instructions 1. General information: The unit utilises passive infrared technology to detect heat radiation of moving human bodies. Upon
More informationEBMPIR-MB. Batten mount PIR detectors. Product Guide. Overview. Features
Product Guide EBMPIR-MB Batten mount PIR detectors Overview The EBMPIR-MB series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual
More informationREPEATER FS5200R INSTRUCTION MANUAL
REPEATER FS5200R INSTRUCTION MANUAL Instruction Manual Page1 CONTENTS 1. Introduction... 3 2. Function... 3 3. Technical data... 3 4. Contents of delivery... 4 5. General information... 5 6. Duty Mode...
More informationMotorised Infrared Optical Beam Smoke Detector. User Guide
Motorised Infrared Optical Beam Smoke Detector User Guide EN 1. General Information 50cm 50cm 8-100m Ensure clear line of sight from Detector to Reflector Mount on solid surfaces (structural wall or girder)
More informationFire Control Panel. Installation & Programming Manual TABLE OF CONTENTS
Fire Control Panel Installation & Programming Manual TABLE OF CONTENTS Page Getting Started 2 Power Supply Unit 3 Remote Keypad Bus 3 Inputs & Outputs 4 User Keypad Functions 5 Engineer Keypad Functions
More information2000W PIR LIGHT CONTROLLER SLB2000-Black SLW2000-White INSTALLATION & OPERATING INSTRUCTIONS
2000W PIR LIGHT CONTROLLER SLB2000-Black SLW2000-White INSTALLATION & OPERATING INSTRUCTIONS SLB2000 PIR LIGHT CONTROLLER - BLACK WEATHERPROOF IP44 PIR SWITCHING 2000w MAXIMUM MANUAL ON/OFF OVERRIDE TIME
More informationEnglish. Italiano. Português. Françias. Español
DT AM Grade 3 Español Françias Português Italiano English High Ceiling Mount Detector Installation Guide English DT AM Grade 3 High Ceiling Mount Detector Installation Guide General Description The Industrial
More informationThe most user friendly Security Alarm System L S Section 1 Overview of System Section 2 Planning your Installation
The most user friendly Contents Section 1 Overview of System 1.1 Kit Contents 1.2 Tools Required 1.3 System Features Security Alarm System L S 4 0 0 Section 2 Planning your Installation 2.1 Location of
More informationDOLKPS1KB Programming & Installation Manual
VANDAL RESISTANT BACK-LIT WEATHERPROOF ACCESS CONTROL KEYPAD WITH WIEGAND OUTPUT & DATA I/O DOLKPS1KB Programming & Installation Manual FOR ELECTRIC LOCK, INTER-LOCK AND SECURITY SYSTEM INSTALLATIONS DOLKPS1KB
More informationRevision November 2013 JVA Technologies. Ethernet General Purpose IO Technical Manual
Revision 1.03 8 November 2013 JVA Technologies Ethernet General Purpose IO Technical Manual www.jva-fence.com.au Table of Contents INTRODUCTION...3 Scope and Purpose...3 Glossary...3 SPECIFICATIONS...4
More informationCeiling PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. PIR Sensor.
Product Guide EBDSM-DD Ceiling PIR presence detector DALI / DSI dimming Overview The EBDSM-DD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationGMA4100-DP. Control Panel. Operation Manual. Worldwide Supplier of Gas Detection Solutions
Worldwide upplier of Gas Detection olutions GfG Instrumentation 1194 Oak Valley Drive, uite 20 Ann Arbor, MI 48108 800-959-0329 tel 734-769-1888 fax email: info@gfg-inc.com GMA4100-DP Control Panel Operation
More informationPRODUCT INSTRUCTIONS. Fire Door Control Panel (FDCP) Stock Code Description Doc No: PI-115. Ellard Fire Door Control Panel Ellard Slave Repeater Unit
PRODUCT INSTRUCTIONS Fire Door Control Panel (FDCP) Floats Rd, Wythenshawe, Manchester. M23 9WB T: 44 (0)161 945 4561 F: 44 (0)161 945 4566 Stock Code Description Doc No: PI115 00133 00134 Ellard Fire
More informationPower Wave. 8 Zone Control Communicator. Crow Electronic Engineering P/L. Ver:8.54. Installation & Programming Guide.
Power Wave 8 8 Zone Control Communicator Crow Electronic Engineering P/L Ver:8.54 Installation & Programming Guide 8 November 2000 Crow ( Aust ) Electronic Engineering Pty Ltd Corporate Head Office: 429
More informationModel: MLSA360N. Installation & Operating Instructions. 360º Night Eye PIR Light Controller
Model: MLSA360N Installation & Operating Instructions 360º Night Eye PIR Light Controller Motion Sensor Detection Perspective View 5 metre 1 Ceiling Mount Position 0º Sensor Tilt Up 3º 3º 5 metre Sensor
More information360 Surface Mount Ceiling PIR Light Controller
360 Surface Mount Ceiling PIR Light Controller Model: SLW360L Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference
More informationPassive Infrared (PIR) Wall Switch Occupancy Sensor Dual Circuit
Instruction Bulletin 63249-420-418A1 02/2014 Passive Infrared (PIR) Wall Switch Occupancy Sensor Dual Circuit Commercial Grade with Ground SLSPWD1277C Retain for Future Use INTRODUCTION The Passive Infrared
More informationFusion Alarm System USER GUIDE
Fusion Alarm System USER GUIDE 020009599 CONTENTS Arming Menu 3 Full Set 3 Disarm 4 Instant Full Set 4 Part Set 5 System fails to set 5 System Alerts 6 Disarming after an alarm, Call Central Station 7
More informationProfile. For a better understanding of this product, please read this user manual thoroughly before using it.
Intelligent GSM Auto-Dial Alarm System User s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. Contents Function Introduction (3) Alarm
More informationProduct Manual SZ1145
Product Manual SZ114 General Purpose Monitor Communicating Controls Description The SZ114 is a microprocessor-based monitoring and alarm interface designed to monitor up to four 1000 Ω platinum temperature
More informationMotorised Infrared Optical Beam Smoke Detector. User Guide
Motorised Infrared Optical Beam Smoke Detector User Guide EN 1. General Information 50cm 50cm 8-100m Ensure clear line of sight from Detector to Reflector Mount on solid surfaces (structural wall or girder)
More informationFLT93 Installation, Operation and Troubleshooting Guide
FLT93 Installation, Operation and Troubleshooting Guide Pre-Installation A. To get the best results from the instrument, the instrument should be mounted 20 pipe diameters downstream from any valve, pipe
More informationFlowJam Bulk Flow Detection
EN Operating Instructions FlowJam Bulk Flow Detection SWR engineering Messtechnik GmbH CONTENTS Page 1. Function............................................................................. 3 2. Safety..............................................................................
More informationDanfoss gas detection units
Data sheet Danfoss gas detection units Types GD Premium, Premium+, Premium Duplex, Premium Remote, Premium Flex and Premium Uptime The Premium line gas detection units are used for monitoring and warning
More informationSystem 800 Addressable Fire Detection & Alarm System
SECTION 5: page 1 Section 5: System 800 Addressable Fire Detection & Alarm System SECTION 5: page 3 10 reasons to specify 800 1 Plug and Play A user friendly panel not requiring special software tools
More informationSENSA MRE DDM MR
96239831 SENSA MRE DDM MR Contents Section Contents Page 1 Dimensional information 1 2 Description and operation 2 3 Wiring and fixing 3 4 Programming 6 5 Wiring diagrams 8 6 Detection pattern diagrams
More information, ,
796-2028, 796-2021, 796-2025 Batten mount PIR detectors Overview This series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual control
More informationHSD-200Z Z-Wave Motion Sensor
HSD-200Z Z-Wave Motion Sensor The HSD-200Z is a Z-Wave TM enabled device and is fully compatible with any Z-Wave TM enabled network. Z-Wave TM enabled devices displaying the Z-Wave TM logo can also be
More informationD-TECT 3 IP. GJD260 IP Motion Detector
D-TECT 3 IP GJD260 IP Motion Detector PACKAGE CONTENTS 1 x D-TECT 3 IP 1 x Drilling template for fixing holes 3 x 31.75mm wall plugs 3 x 31.75mm screws 2 x Spare sliding curtains 2 x Tamper feet 1 x Tamper
More information60W Security Spotlight. 754HB1/180/ Outdoor Motion Sensor. Installation Instructions. Please leave these instructions at the installation site.
60W Security Spotlight 754HB1/180/60 180 Outdoor Motion Sensor Installation Instructions Please leave these instructions at the installation site. Contents 1.0 Introduction... 3 1.1 Features... 3 1.2 Wireless
More informationRPSMLR2 RPSMLR2BB. Panic Device Power Controller Installation Guide LISTED. Rev
RPSMLR2 RPSMLR2BB Panic Device Power Controller Installation Guide LISTED Rev. 102715 Overview: RPSMLR2BB, RPSMLR2 will operate up to two (2) 24VDC panic hardware devices simultaneously. It is designed
More informationHoneywell ENERGY SAVINGS KIT
ENERGY SAVINGS KIT 1. Application The Honeywell Energy Savings Kit reduces energy consumption by sending a dry contact signal to a Honeywell thermostat to change its set-point (increase in cooling mode)
More information12W Round LED Wall/Ceiling Light with Microwave Sensor
12W Round LED Wall/Ceiling Light with Microwave Sensor Model: LEDSR12WHMS Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further
More informationDetailed operating instructions
MA00744002 Detailed operating instructions MD-FLAT 360i/8 RW EP10427886 MD-FLAT 360i/8 SW EP10427893 MD-FLAT 360i/8 RB EP10428074 MD-FLAT 360i/8 SB EP10428081 MD-FLAT-E 360i/8 RW GST EP10427862 MD-FLAT-E
More informationCM-RQE70A PIR REQUEST TO EXIT DETECTOR
Door Activation Devices CM-RQE70A PIR REQUEST TO EXIT DETECTOR THIS PACKAGE INCLUDES (2) #6 x 3/4" Screws (2) 3/16" Wall Plugs (2) MOV's BP7175 1. GENERAL DESCRIPTION Camden CM-RQE70A Request-to-Exit Sensor
More informationWM3000 WIRELESS MODULES
WM3000 WIRELESS MODULES $$:05 $$:07 INSTALLATION INSTRUCTIONS Table of Contents Installation... 3 Mounting Instructions & Connections... 3 Setting the Dip Switches... 4 Setting the Recognition Time...
More informationWARNING FIRE DOOR CLOSING
PRODUCT INSTRUCTIS Stock Code: 088 FCP - Lite Floats Road, Wythenshawe Manchester, M 9WB Tel: + (0) 9 Fax: + (0) 9 Doc No PI - 88 Iss:.0 WARNING FIRE DOOR CLOSING STOP Contents ) Blank ) Features and
More informationSurface Mount Wall PIR Light Controller. Model: PDWM1500. Installation & Operating Instructions
Surface Mount Wall PIR Light Controller Model: PDWM1500 Installation & Operating Instructions 1. Introduction The PDWM1500 utilises passive infrared technology to detect heat radiation of moving human
More informationeasydetect and easydetect deluxe model train detector kits Quickar Electronics, Inc.
easydetect and easydetect deluxe model train detector kits 2011-2012 Quickar Electronics, Inc. INSTRUCTIONS AND DIAGRAMS REVISED APRIL 17 TH 2012 Please note that the color of the calibration trimmer may
More informationSTERLING 10 Control Panel with Remote Keypads ICON and LCD INSTALLATION MANUAL
STERLING 10 Control Panel with Remote Keypads ICON and LCD INSTALLATION MANUAL IMPORTANT: Please note the Sterling 10 LCD keypad is not compatible for use with the Sterling 10 ICON keypad. RINS1413-1 Pyronix
More informationSECURIT 700L PLUS ENGINEERING MANUAL
SECURIT 700L PLUS ENGINEERING MANUAL C & K Systems Ltd 13/03/97 C031-096-02 NEW ENHANCED FEATURE SET Securit 700L PLUS Engineering instructions INTRODUCTION The Securit 700L is a microprocessor intruder
More information18W Round LED Wall/Ceiling Light with Microwave Sensor
18W Round LED Wall/Ceiling Light with Microwave Sensor Model: LEDMR18WHMS Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further
More informationIntelligent Wireless GSM Alarm System
Intelligent Wireless GSM Alarm System 00M2K User s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. Contents [Function Instruction] [Alarm
More informationHigh bay PIR presence detector 1-10V dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
Product Guide EBDSPIR-HB-AD High bay PIR presence detector 1-10V dimming Overview The EBDSPIR-HB-AD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationCeiling PIR HS presence detector 1-10V, low temperature. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
Product Guide EBDHS-AD-LT30 Ceiling PIR HS presence detector 1-10V, low temperature Overview The EBDHS-AD-LT30 PIR (passive infrared) presence detector provides automatic control of lighting loads with
More informationPNC 1000 SERIES 2, 4, 8 Zone Fire Alarm Control Panel
PNC 1000 SERIES 2, 4, 8 Zone Fire Alarm Control Panel INSTALLATION, OPERATION AND MAINTENANCE MANUAL Version: CN-PM-1000.VER1.1-12/2012 EN54 INFORMATION In accordance with EN 54-2 clause 13.7, the maximum
More informationBARDON ROUGHING-IN. A. Specifications A T01-D TOUCHLESS HAND DRYER INSTALLATION INSTRUCTIONS K-5486T
BARDON TOUCHLESS HAND DRYER INSTALLATION INSTRUCTIONS K-586T BEFORE YOU BEGIN Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences.
More information