Bdl60u Fluorescent Emergency Ballast
|
|
- Georgina Franklin
- 5 years ago
- Views:
Transcription
1 A Division Of Philips Electronics North America Corporation One- or two-lamp emergency; Universal input voltage: 120 through 277 V, 50 or 60 Hz; Replaces B60U Bdl60u Fluorescent Emergency Ballast Product Summary UL LISTED Factory or Field Installation (Indoor and Damp) Illumination Time 90 Minutes (Standard) 120 Minutes (One 32 W T8) Initial Light Output Lumens Full Warranty 3 Years (NOT pro-rata) Universal Input Voltage 120 Through 277 V, 50 or 60 Hz Input Current 60 ma Input Power Rating 5.0 Watts Test Switch Double Pole Battery High-Temperature, Maintenance-Free Nickel-Cadmium Battery 7- to 10-Year Life Expectancy Battery Charging Current 280 ma Recharge Time 24 Hours Charging Indicator Light LED Temperature Rating (Ambient) 0 C to +50 C (32 F to 122 F) Dimensions 9.4 x 2.4 x 1.5 (238 mm x 60 mm x 38 mm) Mounting Center 8.9 (226 mm) Weight 2.5 lbs. (1.13 kg) APPLICATION The BDL60U Universal Input fluorescent emergency ballast works in conjunction with an ballast to convert fluorescent fixtures into emergency lighting. The emergency ballast handles a wide range of input voltages and frequencies and consists of a high-temperature nickel-cadmium battery, charger and electronic circuitry in one compact red case. The BDL60U can be used with most W (2-8 ) T8, T10 or T12 fluorescent lamps without integral starters, including U-shaped, HO, VHO, circline and energy-saving, and (4-pin) long compacts (see Table 1). It is also compatible with most 120 through 277 V (50 or 60 Hz) one-, two-, three- and four-lamp electronic, standard, energysaving and dimming ballasts. If used in an emergency-only fixture, no ballast is necessary. The BDL60U is suitable for indoor and damp locations and for sealed & gasketed fixtures, including fixtures rated for wet locations. It is not suitable for air handling heated air outlets or wet or hazardous locations. For information about specific lamp and ballast compatibility, please call the factory. Recommended applications include: international line voltages from 120 through 277 V (50 or 60 Hz); drilling rigs where generators are the primary source of power; and other applications requiring higher tolerance of line voltage variation or harmonic distortion. OPERATION When power fails, the BDL60U immediately switches to the emergency mode, operating either one or two lamps at a reduced lumen output for a minimum of 90 minutes. Two-hour duration may be selected with one 32 W T8 fluorescent lamp. When power is restored, the BDL60U automatically returns to the charging mode. INSTALLATION The BDL60U does not affect normal fixture operation and may be used with either a switched or unswitched fixture. If a switched fixture is used, an unswitched hot lead must be connected to the emergency ballast. The emergency ballast must be fed from the same branch circuit as the ballast. The emergency ballast may be installed inside, on top of or remote from the fixture. The BDL60U may be remotely installed up to half the distance the ballast manufacturer recommends remoting the ballast from the lamp or up to 50 feet, whichever is less. Installation is not recommended with fixtures where the ambient temperature may fall below 0 C. UL and CODE PLIANCE The BDL60U has been tested by Underwriters Laboratories in accordance with the standards set forth in UL 924, "Emergency Lighting and Power Equipment, and is UL Listed for factory or field installation. Emergency illumination time exceeds the National Electrical Code (NEC), Life Safety Code (NFPA LSC) and UL 90-minute requirements. Emergency ballasts can be modified to accomodate longer run times. Specifiers Reference Project Type Model No. Comments L /21/08 The Bodine Company P.O. Box 460 Collierville, TN USA Sales FAX Tech. Support
2 BDL60U Fluorescent Emergency Ballast One- or two-lamp emergency; Universal input voltage: 120 through 277 V, 50 or 60 Hz; Replaces B60U ILLUMINATION Depending on the number (one or two), wattage and type of lamps selected, the BDL60U produces 300 to 700 lumens initial emergency light output (see Table 2). If two-lamp operation is selected, light output is evenly divided between the lamps for better distribution of emergency illumination. SPECIFICATION Emergency lighting shall be provided by using a standard fluorescent fixture equipped with a Bodine BDL60U Universal Input fluorescent emergency ballast. This emergency ballast shall consist of a high-temperature, maintenance-free nickel-cadmium battery, charger and electronic circuitry contained in one 9 3/8 x 2 3/8 x 1 1/2 red metal case. A solid-state charging indicator light to monitor the charger and battery, a double-pole test switch and installation hardware shall be provided. The emergency ballast shall be capable of operating [one or two] fluorescent lamp(s) at lumens (see Table 2) initial light output in the emergency mode for a minimum of 90 minutes or one 32 W T8 fluorescent lamp at reduced illumination in the emergency mode for a minimum of 120 minutes. It shall be suitable for indoor and damp locations and for sealed & gasketed fixtures, including fixtures rated for wet locations. The BDL60U shall have 5 Watts of input power and a 14.4 Watt-hour battery capacity and shall comply with emergency standards set forth by the current NEC. The emergency ballast shall be UL Listed for installation inside, on top of or remote from the fixture and shall be warranted for a full three years from date of purchase. WARRANTY Model BDL60U is warranted for three (3) full years from date of purchase. This warranty covers only properly installed Bodine emergency ballasts used under normal conditions. For the warranty period, Bodine will, at its option, repair or replace without charge a defective emergency ballast, provided it is returned to the factory transportation prepaid and our inspection determines it to be defective under terms of the warranty. Repair or replacement, as stated above, shall constitute the purchaser s exclusive warranty, which does not extend to transportation, installation, labor or any other charges; nor does it apply to any equipment of another manufacturer used in conjunction with the emergency ballast. LAMP DIAMETER 1", 1¼", 1½" T8, T9, T10, T12 Table 1 - Lamp Compatibility BASE Single or Bipin WATTAGE (Length) W (2'-4') NO. of LAMPS () W (5'-8') 1 Long Compact 4-pin (2G11) W 1 Table 2 - Initial Lumen Output LAMP 1 2 LUMENS 1 Lamp 2 Lamps FO32, FBO31 T FO25, FB024 T FO17, FB016 T FO96 T8 700 F40T12, F40/U F40T12/ES (34 W) F96T12 HO, VHO 575 PL-L 40W, F40/30BX, Dulux L 40 W 625 PL-L 36W, F39/36BX, Dulux L 36 W 525 PL-L 24W, F27/24BX/RS, Dulux L 24 W PL-L 18W, F18BX, Dulux L 24 W 375 F382D/4P 625 F282D/4P 450 F212D/4P F162D/4P L /21/08 The Bodine Company P.O. Box 460 Collierville, TN USA Sales FAX Tech. Support
3 bodine BDL Series Fluorescent Emergency Ballasts 2007 The Bodine Company The BDL Series Ballasts are Rated for Damp Location, Vapor-Tight Applications L
4 BDL Series Fluorescent Backup Ballasts When Conditions Are Less Than Perfect... Damp Locations: Partially protected exterior locations under canopies, marquees, roofed open porches and the like, as well as interior locations subject to moderate degrees of moisture such as some basements, barns or cold storage houses. [1] Source: [1] Rea, Mark S. Lighting Handbook-Reference & Application. Illuminating Engineering Society of North America: For more information on the codes applicable to damp locations, see the National Electrical Code, Chapter 14, Codes and Standards. Emergency lighting equipment is included in building designs to provide backup lighting along the path of egress during loss of power so that occupants can exit the building quickly and safely. Because the path of egress often continues outside of a building to a partially protected public way and may include interior areas exposed to moisture, some local codes or building plans require emergency lighting with more than an indoor-dry location rating. Recommended uses include warehouses, covered walkways, parking garages, aircraft hangars, exterior stairways and any other location with damp rated or vapor-type fixtures. 2 Sales Fax
5 bodine Application Bodine damp location emergency ballasts convert partially protected exterior and interior fluorescent fixtures subject to moderate degrees of moisture into unobtrusive emergency lighting fixtures. These emergency ballasts are UL LISTED for damp locations where the ambient temperature for the emergency ballast is 0 C minimum, +50 C maximum. Code Compliance Damp location models have been tested by Underwriters Laboratories in accordance with the standards set forth in UL 924, Emergency Lighting and Power Equipment - Supplement C, and are UL LISTED for installation inside of or on top of the fixture. Emergency illumination exceeds the 90-minute requirement of the National Fire Protection Association s Life Safety Code (NFPA-LSC), the National Electrical Code (NEC) and UL. Damp location models are compatible with a variety of fluorescent lamps, including U- shaped, HO, VHO, circline and energy-saving tubular fluorescent lamps, as well as with 2-pin and 4-pin compact fluorescent lamps. Damp location ballasts are compatible with most electronic, standard, energy-saving and dimming ballasts. Models for one- or twolamp operation are available. For questions concerning specific lamp/ballast compatibility, please call Tech Support at Select Bodine damp location models are UL LISTED for use in sealed and gasketed fixtures. Damp location models are compatible with a variety of fluorescent lamps, including U-shaped, HO, VHO, circline and energy-saving tubular fluorescent lamps, as well as with 2-pin and 4-pin compact fluorescent lamps. Note: See Damp Location Product Summary on the back page for individual product details. Installation Damp location models do not affect normal fixture operation and may be used in either a switched or unswitched fixture. In switched fixtures, an unswitched lead must be connected to the emergency ballast ahead of the wall switch. The emergency ballast may be remotely installed up to one half the distance the ballast manufacturer recommends remoting the ballast from the lamp or up to 50 feet, whichever is less. Battery All damp location models contain hightemperature nickel-cadmium batteries. These batteries are maintenance free, can be safely installed inside the ballast channel and have a life expectancy of 7 to 10 years. Note: If a damp location ballast is used in an emergency-only fixture, no ballast is necessary. 236 Mt. Pleasant Rd. Collierville, TN
6 BDL Series Meeting Global Demands for Superior Technology c Model # Lumen Output # Lamps Operated Type of Lamps Operated Full Warranty BDL500* (B50) lm 2 BDL600* (B60) lm 2 BDL700 (B70A) lm 1 BDL900 (B90) lm 1 BDL94C (B94C) lm 2 17 W W (2-8 ) T8, T10 or T12 4-Pin Long Compact 17 W W (2-8 ) T8, T10 or T12 4-Pin Long Compact 17 W W (2-8 ) T8, T10 or T12 4-Pin Long Compact 17 W - 40 W (2-4 ) T8, T10 or T12 4-Pin Long Compact 6 W - 42 W (4-Pin) Twin, Quad or Triple Twin-Tube 5 Years 3 Years 3 Years 1 Year 2 Years 10 W - 26 W BDL426 (B426) lm 2 2 Years (2-Pin) Twin, Quad or Triple Twin-Tube BDL463 (B463) lm 1 BDL413 (B413) lm 1 10 W - 26 W (2-Pin) Quad or Triple Twin-Tube 5 W - 13 W (2-Pin) Twin or Quad Tube 2 Years 2 Years All models are 120/277 V dual voltage input and suitable for damp locations where the ambient temperature for the emergency ballast is 0 C minimum, +50 C maximum. Damp location models are not recommended for heated air outlets or hazardous location fixtures. For alternate configurations and UL Component Recognized models for hazardous location fixtures, please contact Bodine. For complete technical specifications, please refer to the appropriate dry location counterpart specification sheet. * The BDL500 and BDL600 are UL LISTED for use in sealed and gasketed fixtures. Operation When power fails, the damp location emergency ballast automatically switches to emergency mode, keeping either one or two lamps illuminated at a reduced lumen output for a minimum of 90 minutes. If two-lamp operation is selected, lumen output is evenly distributed between the lamps. When power is restored, the damp location emergency ballast returns to the charging mode. About The Manufacturer Since 1962, The Bodine Company, Inc., has responded to advancements in lamp/ballast technologies by developing a complete line of tubular and compact fluorescent emergency ballasts for a variety of emergency lighting applications. Products are sold through a nationwide network of manufacturers representatives and electrical distributors for field retrofit or directly to lighting fixture manufacturers for factory installation only. The Bodine Company is a member of the Illuminating Engineering Society of North America (IESNA) and the National Electrical Manufacturers Association (NEMA). bodine
7 bodine BDL60U UNIVERSAL INPUT FLUORESCENT Installation Instructions! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter connector must be open. Do not join inverter connector until installation is complete and power is supplied to the emergency ballast. 2. This product is for use with two W (2' - 4') T8, T10 or T12 fluorescent lamps; one W (2' - 8') T8, T10 or T12 fluorescent lamp; two W (4-pin) compact fluorescent lamps without integral starters; or one W (4-pin) compact fluorescent lamp without integral starter. 3. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter connector of the emergency ballast before servicing. 5. This emergency ballast is for factory or field installation in either the ballast channel or on top of the fixture. 6. This product is suitable for damp locations where the ambient temperature is 0 C minimum, +50 C maximum. Product is also suitable for installation in sealed and gasketed fixtures. Product is not suitable for heated air outlets and wet or hazardous locations. 7. An unswitched power source is required (120 through 277 V, 50/60 Hz). 8. Do not install near gas or electric heaters. 9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not field replaceable. Contact the manufacturer for information on service. 10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 11. Do not use this product for other than intended use. 12. Servicing should be performed by qualified service personnel. SAVE THESE INSTRUCTIONS Ni-Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. 04/25/05 The Bodine Company, Inc. 236 Mt. Pleasant Rd. Collierville, TN Tech Support Fax
8 WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON & OUTPUT LEADS PRIOR TO INSTALLATION, MUST BE OPEN. DO NOT JOIN UNTIL INSTALLATION IS PLETE AND POWER IS SUPPLIED TO THE. NOTE: INSTALLATION Make sure that the necessary branch circuit wiring is available. An unswitched source of power is required. The emergency ballast must be fed from the same branch circuit as the ballast. STEP #1 INSTALLING THE > Disconnect power from the fixture. Remove the ballast channel cover and install the emergency * ballast either in the ballast channel or on top of the fixture. > Depending on the type of fixture in use, install emergency ballast using one of the methods illustrated below. Inside Ballast Channel Inside Strip Fixture On Top of Fixture * For installation on top of the fixture, wire bundle covers (RMC-60) may be required by state or local codes. These covers are available from the manufacturer as an accessory kit and must be ordered separately. Call your local distributor or the factory for complete information. STEP #2 INSTALLING THE TEST SWITCH > Refer to the illustrations above and install the test switch through the ballast channel cover of a troffer or through the side of a strip fixture. > Drill a 1/2" hole and install the switch as shown. > Refer to the diagrams below and wire the test switch so that it removes power from both the emergency ballast and the Throw to Test Fixture Toggle Switch Hex Nut Hex Nut Test Switch Leads Leads ballast at the same time. UNSWITCHED FIXTURE SWITCHED FIXTURE TEST SWITCH TEST SWITCH HOT HOT WALL SWITCH
9 INSTALLATION STEP #3 INSTALLING THE > Install the as shown in the illustration below so that it will be visible after the fixture is installed. TROFFER STYLE FIXTURE STRIP STYLE FIXTURE Emergency Ballast Ballast Channel Cover 7/8" Punch Plastic Tubing (please cut to necessary length) Charging Indicator Light Fixture Lens Leads to Charging Indicator Light 7/8" Bushing Inserted into Ballast Channel Cover 1/2" White Bushing to Hold Charging Indicator Light Charging Indicator Light 1/2" White Bushing 1/2" Punch Fixture Violet (+) Brown ( ) 5/8" Black Bushing Charging Indicator Light 1/2" White Bushing Fixture Violet (+) Brown ( ) 5/8" Black Bushing NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label. STEP #4 WIRING THE > Determine the type of ballast installed in the fixture. > Select the appropriate wiring diagram on back to connect the emergency ballast to the ballast and lamp(s). Make sure all connections are in accordance with the National Electrical Code and any local regulations. > After installation is complete, supply power to the emergency ballast and join the inverter connector. > At this point, power should be connected to both the ballast and the emergency ballast and the Charging Indicator Light should illuminate indicating the battery is charging. > A short-term discharge test may be conducted after the emergency ballast has been charging for one hour. Charge for 24 hours before conducting a long-term discharge test. Refer to OPERATION. > In a readily visible location, attach the label "CAUTION - This Unit Has More Than One Power Connection Point. To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And Emergency Power Supplies Before Servicing." When power is applied, the charging indicator light is illuminated, indicating that the battery is being charged. When power fails, the emergency ballast automatically switches to emergency power (internal battery), operating either one or two lamps at reduced illumination for a minimum of 90 minutes. This emergency ballast also operates one 32 W T8 fluorescent lamp in emergency mode for a minimum of 120 minutes. OPERATION MAINTENANCE Although no routine maintenance is required to keep the emergency ballast functional, it should be checked periodically to ensure that it is working. The following schedule is recommended: 1. Visually inspect the charging indicator light monthly. It should be illuminated. 2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. Either one or two lamps should operate at reduced illumination. 3. Conduct a 90-minute discharge test once a year. Either one or two lamps should operate at reduced illumination for at least 90 minutes.! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL! 04/25/
10 AND MUST BE FED FROM THE SAME BRANCH CIRCUIT TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER S. CONSULT THE FTORY FOR OTHER WIRING DIAGRAMS. WIRING DIAGRAMS FOR 1-LAMP OPERATION FIG 36a-UV TWO (2) LAMP INSTANT START FIG 3a-UV TWO (2) LAMP RAPID START /WHT VIOLET TO UNSWITCHED /WHT VIOLET TO UNSWITCHED () () FIG 7a-UV THREE (3) LAMP INSTANT START FIG 15a-UV THREE (3) LAMP RAPID START or YELL /WHT VIOLET TO UNSWITCHED /WHT /WHT /WHT VIOLET TO UNSWITCHED LAMP 3 () LAMP 3 () FIG 14a-UV FOUR (4) LAMP INSTANT START FIG 51a-UV FOUR (4) LAMP RAPID START /WHT VIOLET TO UNSWITCHED /WHT /WHT /WHT VIOLET TO UNSWITCHED LAMP 3 LAMP 3 LAMP 4 () LAMP 4 WIRING DIAGRAMS for 2-LAMP OPERATION (2-4, W lamps only) FIG 36b-UV TWO (2) LAMP INSTANT START FIG 3b-UV TWO (2) LAMP RAPID START /WHT VIOLET TO UNSWITCHED HOT /WHT VIOLET TO UNSWITCHED HOT FIG 7b-UV THREE (3) LAMP INSTANT START FIG 14b-UV FOUR (4) LAMP INSTANT START or YELL /WHT VIOLET TO UNSWITCHED /WHT VIOLET TO UNSWITCHED () LAMP 3 () LAMP 3 () LAMP 4 () WIRING DIAGRAMS for -ONLY fixtures FIG 1a-UV ONE (1) W LAMP WITHOUT FIG 1b-UV TWO (2) W LAMPS WITHOUT CAP CAP /WHT VIOLET TO UNSWITCHED CAP CAP /WHT VIOLET TO UNSWITCHED LAMP LAMP LAMP
LUCE 1 TL. specifications: internal. specifications: external. ordering logic. builder. Job/Location:
LUCE 1 TL indoor / damp Job/Location: Contractor: Prepared By: Job Type: Date: The LUCE-1TL thinline emergency ballast is designed to provide emergency illumination to existing or new fluorescent luminaires.
More informationI-320 SERIES AC EMERGENCY LIGHTING EQUIPMENT
P.O. BOX 84 TUCSON, AZ 85734 (520) 294-3292 FAX (520) 74-2837 www.iotaengineering.com INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be
More informationSAVE THESE INSTRUCTIONS INSTALLATION INSTRUCTIONS EMERGENCY FLUORESCENT BATTERY PACK MODEL PS300, PS600, PS1400
INSTALLATION INSTRUCTIONS EMERGENCY FLUORESCENT BATTERY PACK MODEL PS300, PS600, PS1400 CAUTION: For safety and proper operation, read and follow instructions carefully before installation. FIELD INSTALLABLE
More informationNi - Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
B74CST Installation Instructions SLF-ING MRGNC ING QUIPMNT! IMPTANT SAFGUARDS! WHN USING LCTRICAL QUIPMNT, BASIC SAFT PRCAUTIONS SHOULD ALWAS B FOLLOWD, INCLUDING TH FOLLOWING: RAD AND FOLLOW ALL SAFT
More informationGTD20A Installation Instructions BRANCH CIRCUIT TRANSFER SWITCH/LIGHTING CONTROL DEVICE
Installation Instructions BRANCH CIRCUIT TRANSFER SWITCH/ CONTROL DEVICE UL 1008-BCELTS UL 924-Switch Bypass! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS
More informationSERVICE BY QUALIFIED PERSONNEL ONLY
Installation Instructions Automatic Load Control Relay For Emergency Lighting! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
More informationEmergency Lighting. Product Guide LED. The right source for the. right light
Emergency Lighting Product Guide LED The right source for the right light Contents Emergency Lighting Is Code-Required...... 2 Life Safety Code...4 Emergency Backup Options...6 LED Terminology..........................
More informationBACKUP BATTERY INSTALLATION INSTRUCTIONS
www.tiltlights.com BACKUP INSTRUCTIONS A Lauren International Company www.laurenillumination.com 855 440 8458 LdPE7-2014 SELf-TESTINg EmERgENCY LEd driver RATINGS: Input: 100-277 VAC 50 or 60 Hz Output:
More informationCDL8 LED Architectural
Project: Type: Model# CDL8 LED Architectural PRODUCT DESCRIPTION Retrofit Down lights The Luminoso 8 inch Commercial LED Downlight is damp rated, and suitable for 1-277V Input equipped with fire-rated
More informationESRB and ESRN Installation & Safety Instructions
B1784 ESRB and ESRN Installation & Safety Instructions IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW
More informationINSTALLATION INSTRUCTIONS - PS1055LCP & PS1555LCP LED EMERGENCY DRIVER PS1055LCP & PS1555LCP
LED EMERGENCY DRIVER PS1055LCP & PS1555LCP INSTALLATION INSTRUCTIONS READ AND FOLLOW THESE INSTRUCTIONS BEFORE INSTALLATION TO ENSURE PROPER AND SAFE OPERATION SAVE THESE INSTRUCTIONS LED EMERGENCY DRIVER
More informationINSTALLATION INSTRUCTIONS - POWER SENTRY CONTROL POWER SENTRY CONTROL UNIT PSBCEB2 INSTALLATION INSTRUCTIONS
POWER SENTRY CONTROL UNIT PSBCEB2 INSTALLATION INSTRUCTIONS READ AND FOLLOW THESE INSTRUCTIONS BEFORE INSTALLATION TO ENSURE PROPER AND SAFE OPERATION SAVE THESE INSTRUCTIONS READ AND FOLLOW ALL SAFETY
More informationILB-CP TBTS B MOUNTING DESIGN EMERGENCY LIGHTING EQUIPMENT FOR LED Patented. See iotaengineering.com/patents for more details
P.O. BOX 11846 TUCSON, AZ 85734 (520) 294-3292 FAX (520) 741-2837 www.iotaengineering.com INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 26 ELECTRICAL
SECTION 265100 - INTERIOR LIGHTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Interior lighting fixtures, lamps, and ballasts. 2. Emergency lighting units. 3. Exit signs. 4.
More informationINSTRUCTION MANUAL IMPORTANT SAFEGUARDS. When using electrical equipment, basic safety precautions should always be followed, including the following:
ILB-CP20-HE-A TBTS HIGH EFFICIENCY EMERGENCY LIGHTING EQUIPMENT FOR LED INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including
More informationHIGH BAY APPLICATIONS
STAIRWELLS The IIS Inverter can operate multiple fixtures in a building s stairwell and can be wired to bypass dimmers or occupancy sensors...keeping your egress corridors lit without sacrificing your
More informationSECTION INTERIOR LIGHTING
SECTION 26 51 00 INTERIOR LIGHTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationILB-CP TBTS A MOUNTING DESIGN EMERGENCY LIGHTING EQUIPMENT FOR LED
P.O. BOX 11846 TUCSON, AZ 85734 (520) 294-3292 FAX (520) 741-2837 www.iotaengineering.com INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always
More informationNYC Approved Product Series
NYC Approved Product Series ON THE PROJECT, ON THE SHELF, ON THE JOB NYC APPROVED Table of Contents NYC Approved LED Exit & Combo Series P. 2 NYC Approved LED Battery Series P. 3 NYC Approved Total Edge
More informationLED RETROFIT CONVERSION KITS
Our LED RetroFit Conversion Kits come with a complete Gear Tray Assembly to convert older 4-foot and 8-foot T8 or T12 strip-type fixtures into energy efficient LED luminaires. High quality components and
More informationUltraLITE Model ELU Centralized Emergency Lighting Inverter 4.2 KW- 5 KW
12/23/16 Rev 9 UltraLITE Model ELU General Specification 4.2 KW to 5 KW UltraLITE Model ELU Centralized Emergency Lighting Inverter 4.2 KW- 5 KW 1.0 General General Specification This specification describes
More informationLED RETROFIT CONVERSION KITS
Engineered Products Company s LED RetroFit Conversion Kits convert older 4-foot and 8-foot T8 or T12 strip-type fixtures into energy efficient LED luminaires. High quality components and attractive design
More informationILB-CP TBTS A MOUNTING DESIGN EMERGENCY LIGHTING EQUIPMENT FOR LED
P.O. BOX 11846 TUCSON, AZ 85734 (520) 294-3292 FAX (520) 741-2837 www.iotaengineering.com ILB-CP TBTS A MOUNTING DESIGN EMERGENCY LIGHTING EQUIPMENT FOR LED Patented. See iotaengineering.com/patents for
More informationWINDSOR FOREST HIGH SCHOOL HVAC REPLACEMENT ADDENDUM #2 SAVANNAH CHATHAM COUNTY PUBLIC SCHOOL SYSTEM FEBRUARY 18, 2016
SECTION 26 2030 - LIGHTING FIXTURES PART 1 - GENERAL 1.01 RELATED DOCUMENTS: A. Drawings and general provisions of the Contract, including General and Special Conditions and Division 1 Specification Sections,
More informationLED RETROFIT SOLUTIONS
The adoption of LED technology for general illumination systems is considered the attractive choice when compared against traditional linear fluorescent lamps. Engineered Products Company (EPCO) LED RetroFit
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Flow Lighting QuickLED NEW FIXTURE 2x4 2x2 1x4 Corporate 1240 Texan Trail, Suite 102 Grapevine, TX 76051 (817)435-8484 Office www.flowledlighting.com READ AND FOLLOW ALL SAFETY
More informationLED Emergency Battery Backup Installation Instructions Ordering Code: EB23UQ
LED Emergency Battery Backup Installation Instructions Ordering Code: EB23UQ PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION SAFETY INSTRUCTIONS AND WARNINGS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY
More informationCompatible with most electronic AC ballasts Maintenance-free, long-life, high temperature Ni-Cad battery Durable, heavy duty steel housing 5-year
Compatible with most electronic AC ballasts Maintenance-free, long-life, high temperature Ni-Cad battery Durable, heavy duty steel housing 5-year warranty 1300 Lumens JWEB-1300 The VEM1300DV fluorescent
More informationA. Furnish and install luminaires, lamps, ballasts and in-line fuses as herein specified and shown on the Drawings.
DIVISION 26 ELECTRICAL SECTION 26 51 13 PART 1 GENERAL 1.01 DESCRIPTION A. Furnish and install luminaires, lamps, ballasts and in-line fuses as herein specified and shown on the Drawings. B. Luminaire
More informationSECTION INTERIOR AND EXTERIOR LIGHTING FIXTURES
SECTION 26 50 00 INTERIOR AND EXTERIOR LIGHTING FIXTURES PART 1: GENERAL 1.1 WORK INCLUDED: A. Interior lighting fixtures and accessories B. Exterior lighting fixtures and accessories C. Emergency battery
More informationMANUFACTURED IN THE UK
The Mini-Max range of energy efficient bulkhead fittings are manufactured with a polycarbonate base and diffuser. Together with a poured gasket the Mini-Max leads vandal-resistant IP65 technology. With
More informationDo not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
LED Tube Lamp (Linear Fluorescent Replacement) Retrofit Installation Instructions The product package includes the following components: 1. Integral LED Lamp (1 unit) 2. Fixture Warning Label (1 - self-adhesive)
More informationSECTION INTERIOR LIGHTING
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this Section. 1.2 SUMMARY A. This Section includes the
More information1 General Description
1 General Description LED Tube Light adopts the new type LED as the light source, using the standard TB tube's end caps, makes it easy to install and replace the traditional fluorescent lamp. The TRF-51894
More informationIOTA Exit Signs. IOTA Emergency Fixtures
IOTA Exit Signs IOTA Exit Signs offer a variety of models to meet your interior egress requirements. IOTA Exit solutions are designed and manufactured for efficient, long-lasting performance, easy installation,
More informationNi - Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
50S Installation Instructions SF-SING MRGN QUIPMN! IMPFGURDS! WHN USING RI QUIPMN, SI SF PRUIONS SHOUD WS FOOWD, INUDING H FOOWING: RD ND FOOW SF INSRUIONS 1. o prevent high voltage from being present
More informationLED Emergency Battery Backup
LED Emergency Battery Backup Installation Instructions Ordering Code: PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION: TROFFER INSTALLATION STRIP INSTALLATION INTRODUCTION & TABLE OF CONTENTS Ordering
More informationCL001 >400 Watt lamp basecase, up to 600 Watt replacement fixture $95.00 Fixture
Lighting Specifications Business Please read the details below to ensure you are installing a qualifying product(s). An MID inspection of the pre-existing lighting scheme is required prior to the installation
More informationNightfall. led emergency egress lighting
Nightfall led emergency egress lighting Nightfall led emergency egress lighting Combining a sleek, architectural, low profile design with high performance makes the Nightfall Series an attractive LED solution
More informationRelated Sections: TBD. Effective Date: January 1, 2016
Description: The purpose of the section is to highlight the current applicable UMCP Design Standards for the design, selection and, installation of lighting fixtures within buildings. Related Sections:
More informationSETION EMERGENCY LIGHTING NATIONAL FIRE PROTECTION ASSOCIATION (NEPA) (2006) Life Safety Code, 2006 Edition
SETION 16420 PART 1 - GENERAL 1.01 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation
More informationSECTION INTERIOR LIGHTING
SECTION 26 51 00 INTERIOR LIGHTING PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. NXM Series - Survive-All. Emergency Light Unit
Emergency Light Unit IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Do not
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. HZM-Series-Class I, Div 2 Battery Unit. Instalation instructions
HZM-Series-Class I, Div 2 Battery Unit HZM-Series-Class I, Div 2 Battery Unit Instalation instructions IMPORTANT SAFEGUARDS 1 4 5 6 7 13 When using electrical equipment, basic safety precautions should
More informationTROFFER RETROFIT KIT (TRK)
Not all products are qualified on the DLC QPL. To view our DLC qualified products, please consult the DLC Qualified Products List at www.designlights.org/qpl. TROFFER RETROFIT KIT (TRK) www.trulygreensolutions.com
More informationMODEL RLY-DIM-D INSTALLATION INSTRUCTIONS
MODEL RLY-DIM-D INSTALLATION INSTRUCTIONS IMPORTANT SAFEFGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED. THESE INCLUDE: READ AND FOLLOW ALL SAFETY INSTRUCTIONS
More informationMaxLite LED VAPOR TIGHT LINEAR FIXTURES
A cost effective LED Vapor Tight Fixture features a full length polycarbonate lens and a one-piece white glass reinforced polyester (GRP) body. Designed to meet or exceed seven to 10 foot-candles at 8
More informationBAS SFP22 Edge-lit LED Panel
Project Name Fixture Type Catalog # BAS SFP22 The ultra-thin, edge-lit LED panel (BAS SFP22) series is designed to deliver general ambient lighting in a variety of indoor settings, including schools, offices,
More informationSelecting And Applying Emergency Lighting Systems
bodine Selecting And Applying Emergency Lighting Systems A revision of an article originally published in Electrical Construction & Maintenance by David Crippen, CEO & Marketing Manager Contains updated
More informationWPLED 26W INSTALLATION INSTRUCTIONS
WPLED 26W INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We d like to hear your comments. Call the Marketing
More informationTHE HIGH STAIRWELL AND PASSAGEWAY FIXTURE PERFORMANCE KEY FEATURES INCLUDE:
THE HIGH PERFORMANCE LED Luminaire Series for Stairwells, Bathrooms, Passageways, and General Illumination KEY FEATURES INCLUDE: Multiple Color Options Three color options ensure that the new lighting
More information80W C1D2 Hazardous Location Integrated LED - Corrosion Resistant for Marine - Emergency Backup
80W C1D2 Hazardous Location Integrated LED - Corrosion Resistant for Marine - Emergency Backup Part #: HALP-EMG-48-2L-ITG-LED-V2 Page: 1 Made in Texas The Larson Electronics HALP-EMG-48-2L-ITG-LED-V2 Hazardous
More informationFPLHB - Fidelux Premier Linear Highbay
FPLHB - Fidelux Premier Linear Highbay Product Description Fidelux LED Linear High Bays meet the challenging maintenance, safety, and performance requirements of industrial environments through an unbeatable
More informationHoneywell Durafit LED Retrofit Kit
Honeywell Durafit LED Retrofit Kit INSTALLATION INSTRUCTIONS LED RETROFIT LUMINAIRE CONVERSION FOR USE ONLY WITH PRODUCTS DESCRIBED AND INSTALLED IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED WITH THIS
More informationCatalog Number. Notes. Type. FST Snap on frosted, diffuse L/LENS No diffuser
Catalog Number FEATURES & SPECIFICATIONS INTENDED USE Built on the compact, low-profile Z strip channel, this LED strip offers long maintenance-free life, several color s, lumen outputs and lengths. Ideal
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. 3LERHZ Series Class I, Div 2 Combo Unit. Installation instructions
3LERHZ Series Class I, Div 2 Combo Unit Installation instructions 3LERHZ Series Class I, Div 2 Combo Unit IMPORTANT SAFEGUARDS 1 3 When using electrical equipment, basic safety precautions should always
More informationDioluce Products Installation Instructions
Dioluce Products Installation Instructions Models DL-R24-4530-5K0-001 DL-R24-4530-5K0-002 DL-R24-5035-5K0-001 DL-R24-5035-5K0-002 DL-R24-4530-4K0-001 DL-R24-4530-4K0-002 DL-R24-5035-4K0-001 DL-R24-5035-4K0-002
More information1 x4 Dimmable LED RetroFits
1 x4 Dimmable LED RetroFits Installation Instructions Ordering Code: RF16UQT1XXCDL RF16UHT1XXDL RF32UQT1XXCDL RF32UHT1XXDL PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION OF THE FOLLOWING: 4 STRIP FIXTURES
More informationelite Model ELN Centralized Emergency Lighting Inverter Systems 550 W to 1.5 KW Systems
5/25/16 rev 6 elite Model ELN General Specification 550 W to 1.5 KW elite Model ELN Centralized Emergency Lighting Inverter Systems 550 W to 1.5 KW Systems 1.0 General General Specification This specification
More informationLighting Solutions. from a Leader in Light Source Technology
Lighting Solutions from a Leader in Light Source Technology About Venture Lighting Venture Lighting International, an Advanced Lighting company, was founded in 1983 as a metal halide, high intensity discharge
More informationBusiness Customer Information. Account Number (9 digits) Account Holder Name Phone (As shown on your utility bill) Service Street Address
Commercial Lighting Rebate Application Please complete the application including existing and installed information. Application will be returned without valid purchase receipt/invoice or if equipment
More informationEmergency TLED Lighting Retrofit 101. December 6 th 2017
Emergency TLED Lighting Retrofit 101 December 6 th 2017 From Energy Focus: Brian Danison Director of Engineering Greg Flies Project Manager Yumi Alanoly Product Manager 2 Agenda 1. What is indoor emergency
More informationExplosion Proof C1D2 0-10V Dimmable LED Fixture - 4ft 2 Lamp - Emergency Ballast - Terminal Strips
Explosion Proof C1D2 0-10V Dimmable LED Fixture - 4ft 2 Lamp - Emergency Ballast - Terminal Strips Part #: HAL-EMG-48-2L-LED-D-V2 Page: 1 Made in the USA The Larson Electronics HAL-EMG-48-2L-LED-D-V2 Hazardous
More informationTSLED STAIRWELL INSTALLATION INSTRUCTIONS
TSLED STAIRWELL INSTALLATI INSTRUCTIS TSLED- 2FT TSLED - 4FT IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with
More informationCatalog Number. Notes
Catalog Number FEATURES & SPECIFICATIONS INTENDED USE Built on the compact, low-profile Z strip channel, this LED strip offers long maintenance-free life, several color s, lumen outputs and lengths. Ideal
More informationLED Lighting: Technology Selection and System Commissioning Course Number: CXENERGY1519
AABC Commissioning Group AIA Provider Number: 50111116 LED Lighting: Technology Selection and System Commissioning Course Number: CXENERGY1519 Michael Chow, P.E., CxA, LEED AP BD+C, Metro CD Engineering
More informationDISTRIBUTOR SELECT COLLECTION. EMERGI-LITE Full range of emergency lighting solutions
COLLECTION EMERGI-LITE Full range of emergency lighting solutions Distributor Select products Popular emergency lighting products are in stock and ready to ship from warehouses across North America for
More informationMaxLite LED High Bay Fixtures
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationVENTILATION FAN. MFG Model : VFB80HLED2/VFB080C4L2 /VFB080C4LED2/ VFB100HLED2/VFB100C4LED1 READ AND SAVE THESE INSTRUCTIONS
VENTILATION FAN MODEL 80HLED/80L/80LED/00HLED/00LED TABLE OF CONTENTS Package Contents General Safety Information 3 Preparation Assembly Instructions 5 New Construction 5 Existing Construction 6 Connect
More informationPSO Business Rebates Retrofit Lighting Technical Requirements
PSO Business Rebates Retrofit Lighting General LED Requirements LED replacement and LED luminaires must be listed on the Design Lights Consortium (DLC) or ENERGY STAR Qualified Products List (QPL). DLC
More informationInstallation Instructions
Installation Instructions Ordering Code: RF16UQT1XXC RF32UQT1XXC RF32UHT1XX RF45UQT1XXC RF45UHT1XX PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION OF THE FOLLOWING: 4 STRIP FIXTURES 8 STRIP FIXTURES
More informationTRUELITE LED TUBE.
Not all products are qualified on the DLC QPL. To view our DLC qualified products, please consult the DLC Qualified Products List at www.designlights.org/qpl. TRUELITE LED TUBE www.trulygreensolutions.com
More informationLED retrofits! 4 T8 Specification Guide. Retrofit your existing Fluorescent Lights in Seconds No Electrician Needed! Pure Bright
T8 PBT8-DL5004EFX-U AC 100V-277V Day Light 5000K Pure Bright LED retrofits! Retrofit your existing Fluorescent Lights in Seconds No Electrician Needed! With the highest safety rating available, UL Listed,
More information2018 Instant Lighting Rebates Product Catalog
MIDSTREAM LIGHTING PRODUCTS Product Code 463993 Interior 4 LED T8 Lamp Product Description Rebate/Unit Page # $5.00/Lamp 8 464791 Commercial LED Candelabra: 1 to
More informationApplication Note. Using XPoint Wireless Devices with Emergency Lighting. 1 of 16
Using XPoint Wireless Devices with Emergency Lighting 1 of 16 Table of Contents Introduction...3 Application Summary...3 UL924 Standard Summary...4 ER Option - Normal Power Sensing Leads...4 ER Intended
More informationVenture Lighting s Line of LED Solutions. Professional Grade LED from The Leader in HID
Venture Lighting s Line of LED Solutions Professional Grade LED from The Leader in HID About Venture Lighting Venture Lighting International, an Advanced Lighting company, was founded in 1983 as a metal
More informationApplications. Standard Materials
Mercmaster III Low Profile Compact Fluorescent Luminaires Compact Fluorescent listed for simultaneous exposure to combustible dusts and flammable gases or vapors. Applications Enclosed and gasketed fixtures
More informationLumination LED Luminaires
GE Lighting Lumination LED Luminaires Recessed LED Troffer BT Series Refreshing Retrofit New Lumination BT Series Recessed LED Troffers from GE Lighting provide all the advantages of LED lighting at a
More informationExplosion Proof Emergency Fluorescent Light Combination - Dimmable Ballast - C1D1-2 T8 lamps - 4'
Explosion Proof Emergency Fluorescent Light Combination - Dimmable Ballast - C1D1-2 T8 lamps - 4' Part #: EPL-EMG-48-2L-T8-D Made in the USA The Larson Electronics EPL-EMG-48-2l-T8-D Explosion Proof Emergency
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-26 52 00.00 40 (November 2017) ----------------------------------- Preparing Activity: NASA Superseding UFGS-26 52 00.00 40 (August 2014) UNIFIED FACILITIES GUIDE SPECIFICATIONS
More information2. Lighting fixtures mounted on exterior building surfaces.
PART 1 - GENERAL... 1 1.1 RELATED DOCUMENTS... 1 1.2 SUMMARY... 1 1.3 DEFINITIONS... 2 1.4 SUBMITTALS... 2 1.5 QUALITY ASSURANCE... 3 1.6 COORDINATION... 3 1.7 WARRANTY... 4 1.8 EXTRA MATERIALS... 4 PART
More informationS5JB Quick Setup Guide. Refer to the instructions on the following pages for complete details on the steps outlined below.
Intelligent Junction Box -, HW 1 Mount, Lighting Fixtures and Control Equipment Mount the on C-strut or other suitable mounting location. Install the lighting fixtures and other specified control equipment
More informationLED IMPORTANT SAFETY INSTRUCTIONS
LED IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage
More information48W Fluorescent T8 Light w/ Emergency Backup Dimmable Ballast - (2) 2 Foot T8 Lamps - C1D2
48W Fluorescent T8 Light w/ Emergency Backup Dimmable Ballast - (2) 2 Foot T8 Lamps - C1D2 Part #: HAL-EMG-24-2L-T8-D Page: 1 Made in the USA The Larson Electronics HAL-EMG-24-2L-T8-D Hazardous Area Fluorescent
More informationlight ACL9 ANATOMY PERIMETER FOCUSED INSTALLATION SLEEK & STRONG
ACL9 ACL9 ANATOMY SLEEK & STRONG A stylish rectilinear aluminum extrusion made of 60% recycled material provides ultimate durability and functionality. 3.325 2.25 0.63 PERIMETER FOCUSED INSTALLATION A
More informationBATH FAN / LED LIGHT READ AND SAVE THESE INSTRUCTIONS MODEL GBR100LED-DECOR TABLE OF CONTENTS. Package Contents 2. General Safety Information 3
BATH FAN / LED LIGHT MODEL GBR100LED-DECOR TABLE OF CONTENTS Package Contents 2 General Safety Information 3 Preparation Assembly Instructions 5 New Construction 5 Existing Construction 6 Glass shade installation
More informationRelay Panel and Relay Panel Module Wiring and installation manual Light is OSRAM
www.osram.us/extend Relay Panel and Relay Panel Module Wiring and installation manual Light is OSRAM Overview The Relay Panel is an addressable lighting control panel that fully integrates with the ENCELIUM
More informationRAZOR RZR SERIES DIE CAST ALUMINUM LED EXIT SIGNS INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
RAZOR RZR SERIES DIE CAST ALUMINUM LED EXIT SIGNS INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including
More informationThe New Lux-Ray LED Emergency Lighting
ON THE PROJECT, ON THE SHELF, ON THE JOB The New Lux-Ray LED Emergency Lighting RUGGED. VERSATILE. SOPHISTICATED MINIATURIZATION The New Lux-Ray LED Emergency Lighting For first-class performance in emergency
More informationLighting Solutions from a Leader in Light Source Technology
Lighting Solutions from a Leader in Light Source Technology 2016 Venture Lighting International About Venture Lighting Worldwide innovator, manufacturer and supplier of energy efficient lighting materials,
More information4' 2 Lamp Fluorescent Light Fixture - Emergency Battery Backup - T8 Bulbs - Multi-voltage - CID2
4' 2 Lamp Fluorescent Light Fixture - Emergency Battery Backup - T8 Bulbs - Multi-voltage - CID2 Part #: HALS-EMG-48-2L-T8 Made in the USA The Larson Electronics HALS-EMG-48-2L-T8 Hazardous Area Fluorescent
More informationSpectron LSN (Life Safety Network) Suggested Specifications
1. General 1.1 Scope A Dual-Lite Spectron LSN (Life Safety Network) Series Inverter System shall be furnished to provide a reliable source of power, and shall operate during a utility line deficiency without
More informationProject Name. Date. Cat. Number. Type
Linear Series 2.0 LED linear luminaires and retrofit linear kits The Linear Series delivers ultra-long life and high efficacy. Fixtures can be installed independently or joined together for continuous-run
More informationMN/DOT Specification Sign Lighting Luminaire With 150 or 250 Watt Metal Halide Lamps 11/05/09
1. LISTING REQUIREMENTS MN/DOT Specification Sign Lighting Luminaire With 150 or 250 Watt Metal Halide Lamps 11/05/09 1.1. The Luminaire shall be listed by a National Recognized Testing Laboratory (NRTL)
More informationHEP Tech Co., Ltd. Company Profile
HEP Tech Co., Ltd. Company Profile HEP Group Structure 1. HEP Tech Co., Ltd. Head office / Global sales team / R&D center 2. HEP GmbH Europe sales office / Warehouse / Europe R&D center & DEKRA certified
More informationSelecting & Applying Emergency Lighting Systems
Selecting & Applying Emergency Lighting Systems 10.1 Philips Emergency Lighting www.philips.com/bodine Philips Emergency Lighting 2 Emergency Lighting Mandated by State and Local Laws Emergency illumination
More informationREVISIONS Summary of Change. 6/1/12 All Replaced entire document with new revision
Revision Date Section REVISIONS Summary of Change 6/1/12 All Replaced entire document with new revision REV 6/12 1 of 5 UNIVERSITY CONTACT: EXTERIOR LIGHTING Electrical Services, Maintenance & Operations
More informationPRODUCT DATA SHEET LIGHTING PRODUCTS
EPCO s LED s are available in nineteen (19) configurations that are vapor tight, provide unparalleled performance, improved efficacy, more lumens per watt, and are the reliable, sustainable solid-state
More informationSECTION EXTERIOR LIGHTING
SECTION 26 56 00 PART 1 - GENERAL 1.1 DESCRIPTION This section specifies the furnishing, installation, and connection of exterior luminaries, controls, poles and supports. 1.2 RELATED WORK A. Section 26
More informationExit/Emergency Lighting Guide
Exit/Emergency Lighting Guide 1 Exit/Emergency Lighting Guide Table of Contents Exit Signs... 3 Exit/Emergency Combo... 5 Emergency Lights... 7 Accessories... 14 Emergency Ballasts... 17 2 HL0301 Compact
More information