Technical Manual. LeakFilm Pro. Single Channel Conductive and Chemical Liquid Leak Detection Controller with Leak Location Detection

Transcription

1 Technical Manual LeakFilm Pro Single Channel Conductive and Chemical Liquid Leak Detection Controller with Leak Location Detection

2 1. Safety Ensure that this Operating Manual is read and understood BEFORE installing / operating / maintaining the equipment. Pay particular attention to Warnings and Cautions. All document Warnings are listed here and repeated where appropriate at the start of the relevant chapter(s) of this Operating Manual. Cautions appear in the sections/sub-sections of the document where they apply. WARNINGS LeakFilm controllers and sensors are designed for installation and use in ordinary areas only. Do not install the controllers and the sensors in hazardous areas. Installation must be in accordance with the recognised standards of the appropriate authority in the country concerned. Access to the terminal block for wiring and switches for configuration of the controller, when carrying out any work, must only be conducted by trained personnel. Before carrying out any work ensure local regulations and site procedures are followed. Appropriate standards must be followed to maintain the overall certifications. Never attempt to open a plastic enclosure or connector or replace/refit the wire of the sensor while power is still applied to the controller. LeakFilm controllers must be earthed/grounded for electrical safety and to limit the effects of radio frequency interference. Earth/ground points are provided F.G. or SHIELD terminal of the controllers. Ensure that all screens/instrument earth/clean earth wiring is earthed/grounded at a single point (either at the controller or master controller - BUT NOT BOTH) to prevent false readings or alarms that may occur due to potential earth/ground loops. The plastic enclosure of the controllers is a potential electrostatic charging hazard. Avoid any conditions that could result in the controllers becoming electrostatically charged. Take care when handling LeakFilm sensors as they may be damaged by sharp tools. LeakFilm controllers should be handled with care to avoid mechanical shock and impact. Do not expose to temperatures, humidity and other conditions beyond the storage and operating ranges. LeakFilm controllers must have a suitably rated fuse. LeakFilm controllers and sensors should be installed in a location free from dust, direct sunlight, temperature extreme, strong magnetic field and heavy vibration. 2

3 2. Information This manual is for use with LeakFilm Sensors and Controllers range only. The Start-up/Surge/In rush current is dependent on the type of power supply used. The typical start-up current for LeakFilm Pro is less than 240mA at 24VDC. Measure the start-up current using the specific power supply before installation to ensure suitability for your application. Honeywell Analytics can take no responsibility for installation and/or use of its equipment if not done so in accordance with the appropriate issue and/or amendment of the Technical Manual. The reader of this Operating Manual should ensure that it is appropriate in all details for the exact equipment to be installed and/or operated. If in doubt, contact Honeywell Analytics for advice. The following types of notices are used throughout this Operating Manual: WARNING Identifies a hazardous or unsafe practice which could result in severe injury or death to personnel. Caution: Identifies a hazardous or unsafe practice which could result in minor injury to personnel, or product or property damage. Note: Identifies useful/additional information. Every effort has been made to ensure the accuracy of this document, however, Honeywell Analytics can assume no responsibility for any errors or omissions in this document or their consequences. Honeywell Analytics would greatly appreciate being informed of any errors or omissions that may be found in the content of this document. For information not covered in this document, or if there is a requirement to send comments/ corrections about this document, please contact Honeywell Analytics using the contact details given on the back page. Honeywell Analytics reserve the right to change or revise the information supplied in this document without notice and without obligation to notify any person or organisation of such revision or change. If information is required that does not appear in this document, contact the local distributor/agent or Honeywell Analytics. 3

4 3. Table of Contents 1 Safety 2 2 Information 3 3 Table of contents 4 4 Introduction Package Contents LeakFilm Sensors LeakFilm Connectors 8 5 Installation Mounting and Location Sensor installation Typical examples of installing the sensor 10 6 Electrical connections and power on Terminal connections Connection with LeakFilm MC (Master Controller) Power on (Commissioning) 16 7 Menu and Advanced Configuration Review Mode Leak and Broken Sensor Advanced Configurations 21 8 Characteristic and specification 25 9 Ordering Information Warranty statement Installation Drawing 28 4

5 4. Introduction LeakFilm Pro is a controller connected to either the LeakFilm Conductive_D or the LeakFilm Chemical sensor to detect conductive or chemical liquid leaks respectively with location detection. The controller features a buzzer, 5 push buttons UP, DOWN, SET, MODE and RESET for configuration, 5 LEDs indicating the status of FAULT, LEAK, POWER and Tx & Rx for communication status, and 8x2 character LCD for status indication and configuration. The controller also provides a relay for controlling external equipment such as alarms, sirens, valves or switches. Due to the fast response time of the LeakFilm sensors, the controller can detect a leak within a few seconds with leak location and up to 200m of sensor can be connected. The controller can detect a broken sensor as well as a liquid leak. When the broken sensor is detected, the fault LED is activated and it is displayed in the LCD. LeakFilm Pro has been designed to be mounted through 2 mounting holes, so that the user can easily install the controller on a wall or in the interior of an electrical control panel easily. LeakFilm Pro provides advanced communication functions (RS-485), so that it can be connected to the LeakFilm MC (Master Controller) which can monitor the status of up to 200 controllers. Serial communication terminal Relay contact terminal Buzzer Status LEDs Push buttons for configuration Sensor connection terminal Power connection terminal Power Switch Diagram 1: LeakFilm Pro Overview 5

6 4. Introduction Caution: LeakFilm Pro can only be used with either LeakFilm Conductive_D or LeakFilm Chemical, so that it can detect only water or conductive liquid or chemical leaks. LeakFilm Conductive_D and Leakfilm Chemical cannot be combined with the same controller. To detect a hydrocarbon leak, use LeakFilm HC. 4.1 Package Contents LeakFilm Pro is supplied with pre-configured and 100% tested controller, manual CD-ROM and package box as shown below. The CD-ROM should run automatically when put into a computer CD-ROM player. If the CD-ROM does not start, click on My Computer, locate the CD-ROM and double click the file start.exe. LeakFilm Pro Manual CD Diagram 2: Package Box Contents WARNINGS When unpacking the product, handle with care to avoid any damage to the product. Do not throw away the box, which may be required for product storage or transport, and keep it together with the manual. 6

7 4.2 LeakFilm Sensors 4. Introduction LeakFilm Pro can be used with either the LeakFilm Conductive_D or the LeakFilm Chemical sensors, so that it can detect chemical or water or conductive liquid. There are 6 different types of ordering part numbers for LeakFilm Conductive_D and LeakFilm Chemical depending on the length. LeakFilm Conductive_D LeakFilm Chemical Diagram 3: LeakFilm Conductive_D and Chemical Part number Product Name Description HLFSSCND meter Conductive Sensor with Leak Position Detection HLFSSCND-050 LeakFilm Conductive_D 50 meter Conductive Sensor with Leak Position Detection HLFSSCND-001 Custom Length Conductive Sensor with Leak Position Detection HLFSSAND meter Chemical Sensor with Leak Position Detection HLFSSAND-050 LeakFilm Chemical 50 meter Chemical Sensor with Leak Position Detection HLFSSAND-001 Custom Length Chemical Sensor with Leak Position Detection Table 1: LeakFilm Conductive Sensors 7

8 4.3 LeakFilm Connectors 4. Introduction LeakFilm provides 4 different types of connectors which are suitable for various installation environments. LeakFilm connectors were designed to be assembled by snapping, so that only a screw driver is required for assembly. Refer to the LeakFilm Sensor Technical Manual (3013M5006) for instructions on how to assemble the sensor into the connector Diagram 4: LeakFilm Connectors No Part number Product Name Description 1 HLFNCJND-000 Cable Jump Connector with 15cm Lead Wire Jump Connector HLFNCJND-001 Cable Jump Connector with 1m Lead Wire 2 HLFNCEND-000 End Connector 4 Lines End Connector 4 Lines 3 HLFNCLND-000 Elbow Connector Elbow Connector 4 HLFNCSND-005 Start Connector Start Connector with 5 m Lead Wire Table 2: LeakFilm Connectors Caution: LeakFilm Conductive_D and LeakFilm Chemical sensors should be used with 4 lines end connector (HLFNCEND-000). 2 lines end connector is not applicable. 8

9 5. Installation WARNINGS LeakFilm controllers and sensors are designed for installation and use in ordinary areas only. Do not install the controllers and the sensors in hazardous areas. Installation must be in accordance with the recognised standards of the appropriate authority in the country concerned. Access to the terminal block for wiring and switches for configuration of the controller, when carrying out any work, must only be conducted by trained personnel. Before carrying out any work ensure local regulations and site procedures are followed. Appropriate standards must be followed to maintain the overall certifications. Never attempt to open a plastic enclosure or connector or replace/refit the wire of the sensor while power is still applied to the controller. LeakFilm controllers must be earthed/grounded for electrical safety and to limit the effects of radio frequency interference. Earth/ground points are provided F.G. or SHIELD terminal of the controllers. Ensure that all screens/instrument earth/clean earth wiring is earthed/grounded at a single point (either at the controller or master controller - BUT NOT BOTH) to prevent false readings or alarms that may occur due to potential earth/ground loops. The plastic enclosure of the controllers is a potential electrostatic charging hazard. Avoid any conditions that could result in the controllers becoming electrostatically charged. Take care when handling LeakFilm sensors as they may be damaged by sharp tools. LeakFilm controllers should be handled with care to avoid mechanical shock and impact. Do not expose to temperatures, humidity and other conditions beyond the storage and operating ranges. LeakFilm controllers must have a suitably rated fuse. LeakFilm controllers and sensors should be installed in a location free from dust, direct sunlight, temperature extreme, strong magnetic field and heavy vibration. 9

10 5.1 Mounting and Location 5. Installation LeakFilm Pro is designed to be mounted through 2 mounting holes, so that the user can easily install the controller on a wall or in the interior of an electrical control panel. The following points should be noted when locating the controllers. When locating the controllers, consider the possible damage caused by natural events e.g. rain or flooding. LeakFilm Pro is not water proof (IP20). Consider ease of access to the controller for repair and maintenance. Avoid any location mentioned in the above warnings. See the installation drawing at the end of this manual for mechanical dimensions. 5.2 Sensor installation LeakFilm sensor has double sided tape to adhere to the floor or a flat surface. The following points should be noted when installing the sensors. The surface should be clean for better adherence to the sensor. Glue or adhesive can be used in addition to standard double sided tape if the surface is not flat or not suitable for double sided tape. 5.3 Typical examples of installing the sensor Overall length of the sensor should be less than 200 meters and overall length of the lead wire should be less than 50 meters. Case 1: Standard lead wire and custom length of single sensor Start Connector PN: HLFNCSND-005 Start Connector PN: HLFNCSND-001 5m 0.5m ~ 200m Diagram 5: Case 1 10

11 5. Installation Case 2: Standard lead wires and custom length of multiple sensors Start Connector PN: HLFNCSND-005 Jump Connector PN: HLFNCJND-0XX 5m L1 0.15m End Connector PN: HLFNCEND-000 L2 L1 + L2 = Max. 200m Diagram 6: Case 2 Case 3: Custom length of lead wire and custom length of single sensor Lead Wire (UTP CM/CP 2PR 24AWG CAT5) Max 50m 5m 0.5m ~ 200m Start Connector PN: HLFNCSND-005 End Connector PN: HLFNCEND-000 Diagram 7: Case 3 11

12 5. Installation Case 4: Custom length of lead wires and custom length of multiple sensors Start Connector PN: HLFNCSND-005 Jump Connector HLFNCJND-0XX #1 5m L1 #2 End Connector PN: HLFNCEND-000 L2 Sensor: L1 + L2 = Max. 200m Lead Wire: #1 + #2 = Max. 50m Diagram 8: Case 4 Caution: Maximum length of sensor and lead wire depends on the sensor and controller type. 12

13 6. Electrical connections and power on 6.1 Terminal connections WARNINGS All electrical connections should be made in accordance with any relevant local or national legislation, standards or codes of practice. LeakFilm controllers must be earthed/grounded for electrical safety and to limit the effects of radio frequency interference. Earth/ground points are provided F.G. or SHIELD terminal of the controllers. All electrical connections must be terminated correctly as per below wiring diagram. Otherwise the controller will not operate properly. RS-485 Relay Output (NO) Relay Output (NC) Relay Output Common DC 20V ~ 36V GND Power S/W Basic Length: 5m Lead wire can be extended up to 50m using UTP CM/CP 2PR 24 AWG Cat5 Start Connector PN: HLFNCSND-005 End Connector HLFNCEND-000 Diagram 9: Wiring Diagram 13

14 6. Electrical connections and power on Marking Group Description W White wire of LeakFilm Conductive_D or Chemical sensor B Blue wire of LeakFilm Conductive_D or Chemical sensor Y Signal Input Yellow wire of LeakFilm Conductive_D or Chemical sensor R Red wire of LeakFilm Conductive_D or Chemical sensor SHIELD Shield wire of LeakFilm Conductive_D or Chemical sensor Rx RS-485 To Rx of LeakFilm MC Tx Communication To Tx of LeakFilm MC NO Normal open of the relay. NO and COM closed when leak or fault. NC Relay Normal close of the relay. NC and COM open when leak or fault. COM Common of the relay GND Ground (0VDC) of power supply Power 20~36V +V of power supply. 24VDC Nominal. Table 3: LeakFilm Pro Controller Terminal Connections 14

15 6. Electrical connections and power on 6.2 Connection with LeakFilm MC (Master Controller) Up to 200 LeakFilm Pro units can be connected to LeakFilm MC using RS-485 communication. Each controller should have a unique communication ID. See Set Communication ID menu for instructions on how to set the ID. All Tx lines should be connected to Tx terminal of J8 of LeakFilm MC and all Rx lines to Rx terminal of J8 of LeakFilm MC. ID: 1 ID: 2 ID: 3 ID: 200 Max. 200 units Diagram 10: Wiring diagram to master controller Caution: Each controller connected to LeakFilm MC should have a unique communication ID, otherwise incorrect data can be transmitted to the master controller. 15

16 6. Electrical connections and power on 6.3 Power on (Commissioning) Caution: The following procedure should be followed carefully and only performed by suitably trained personnel 1. Check that all electrical connections are terminated correctly as per the wiring diagram. 2. Switch on the power supply to the controller. 3. Using a Digital Multi Meter (DMM), check the supply voltage at the terminals GND and 20-36V. The measured voltage should be in the range of VDC. 4. Switch off and on again. 5. A start up sequence will then be displayed, similar to the one shown in the diagram below. 6. It will take 2 seconds per step. Version 1.0 RS-485 LeakFilm Range010 LCD & LED Display 2 seconds delay 2 seconds delay FAULT LEAK POWER FAULT LEAK POWER FAULT LEAK POWER Version display Communication Sensor length display Description Sensitiv Val:Midd 2 seconds delay FAULT LEAK POWER Sensitivity level display 2 seconds delay 16

17 6. Electrical connections and power on LeakTime CNT:02 FAULT LEAK POWER Leak delay time display AUTORUN 12:00:11 2 seconds delay FAULT LEAK POWER Normal Monitoring Mode Table 4: Start up sequence 7. After going through all of the above procedures correctly, set the length of the sensor. Refer to section 7.3 Advanced configuration to see how to set the sensor length. 8. Calibrate the sensor distance by using the Min and Max set menu. 9. If the controller uses the communication function, set the ID using the Set Communication ID menu. 10. If required, set the date and time using the Set Date and Time menu. Date and time is used in the data logging function. 11 LeakFilm Pro and LeakFilm Conductive_D can be tested by dropping a small amount of water onto the sensor to check for correct operation. Caution: LeakFilm Chemical does not respond to water. 17

18 7. Menu and Advanced Configuration 7.1 Review Mode The controller will enter review mode when the MODE button is pushed. This mode allows the user to view current date and time, log data and other configurations as shown in the table below. The user can go to the next item by pushing the MODE button. LCD Display & Button Operation AUTORUN 12:04:11 Normal monitoring mode Description MODE button 08/08/08 12:00:00 Current Date and Time MODE button LOG DATA CNT:01 Log data; Log data can be reviewed by UP and DOWN button. A total of 9 log data can be saved in the controller. MODE button ID Num ID:XXX ID for communication; Communication ID can be set between 1 and 200. MODE button AUTORUN 12:05:11 Normal monitoring mode Table 5: Review Mode 18

19 7. Menu and Advanced Configuration 7.2 Leak and Broken sensor Once the controller detects a leak, the LEAK LED is activated and the leak location is displayed on the LCD as shown in the table below. The relay and buzzer are activated in parallel. AUTORUN 12:00:11 LCD & LED Display FAULT LEAK POWER Normal monitoring mode Description LEAK!!! Check... LEAK!!! 11.5M Leak detected AUTORUN 12:00:11 Leak detected FAULT LEAK POWER FAULT LEAK POWER FAULT LEAK POWER Leak alarm with two beeps repeatedly Leak location displayed. Distance from the controller excluding lead wire. Normal monitoring mode Table 6: Leak alarm When the controller detects a broken sensor, the FAULT LED is activated and the failure mode is displayed on the LCD as shown in the table below. The relay and buzzer are activated in parallel. 19

20 7. Menu and Advanced Configuration AUTORUN 12:00:11 LCD & LED Display Broken sensor detected BROKEN No:X Broken sensor detected AUTORUN 12:00:11 FAULT LEAK POWER FAULT LEAK POWER FAULT LEAK POWER Normal monitoring mode Description Broken sensor alarm with single beep repeatedly. No 1: White or Blue wire open No 2: Yellow or Red wire open No 3: All wires open Normal monitoring mode Table 7: Broken sensor alarm Diagram 11: Leak & Broken sensor alarm Caution: Broken sensor fault has priority, so LCD displays broken sensor fault when both leak and broken sensor happen together. 20

21 7. Menu and Advanced Configuration 7.3 Advanced Configurations Caution: It is necessary for correct operation of the sensor that the sensor length is set Set Sensor Length SET + DOWN Button RangeSet Range010 Set the length by UP & DOWN button m in 1m steps. Confirm by SET button, then completed with beep. Table 8: Sensor length setting The length of LeakFilm sensor must be set using this menu before use. The length can be adjusted using the UP and DOWN buttons with 1 meter resolution. The value should be within the range of 3 to 200 meters. Setting is completed with a beep. Calibrate Sensor Distance (Start Point) SET + MODE Button Range200 INITIAL Push DOWN button. Range200 Min Set Short the start point of the sensor, then completed with a beep. Calibrate Sensor Distance (End Point) SET + MODE Button Range200 INITIAL Push UP button. Range200 Max Set Short the end point of the sensor, then completed with a beep. Table 9: Sensor distance calibration LeakFilm Conductive_D and Chemical sensor should be calibrated prior to use for better accuracy of leak location. Both start and end point should be calibrated one at a time. Push the SET and MODE buttons simultaneously then the RANGE INITIAL message will appear. Short two leak holes at the start point of the sensor with tweezers or equivalent tools as shown in the diagram below and push the DOWN button to set the start point of the sensor. Short two leak holes at the end point of the sensor with tweezers or equivalent tools as shown in the diagram below and push the UP button to set the end point of the sensor. The calibration is completed with a beep. 21

22 7. Menu and Advanced Configuration Start Connector Short by tweezers End Connector Start Point Start Connector Short by tweezers End Connector End Point Diagram 12: How to short the start and end point Set Leak Delay Time SET + MODE Button Range200 INITIAL Push SET button. LeakTime CNT:1 Set the time by UP & DOWN button. 1~30 counts. Confirm by SET button, then completed with beep. Table 9: Leak delay time setting Delay time determines how fast the LeakFilm Pro responds to the leak signal from the sensor. The user can set the value CNT within the range of 1 to 30 counts. From this, the actual response time can be calculated as shown below. Actual response time = (0.64 sec x CNT) + 2 seconds e.g. If CNT is 5, response time = 0.64 x = 5.2 seconds The default value of CNT is 2 and the actual response time of the controller in ideal case is around 3 seconds. If the controller and sensor are installed in an electrically noisy or high humidity environment, the CNT value should be larger to minimise the possibility of nuisance alarms. In a normal environment, default CNT value (=2) would work well. 22

23 7. Menu and Advanced Configuration Set Sensitivity MODE + RESET Button Sensisit Val:Midd Set the sensitivity by UP & DOWN button. High, Middle, Low. Confirm by SET button, then completed with beep. Table 10: Sensitivity setting The default value is Middle and the user should not need to adjust the sensitivity in most cases. Please contact Honeywell Analytics for details. Noise Level Display DOWN + RESET Button NoiseVal 000mV See noise level from the sensor Table 11: Noise level display This menu shows the noise level from the sensor in mv. If the level is more than 250mV, nuisance alarms may occur. Remove the source of electrical noise from the sensor or increase the leak delay time in the menu. Set Communication ID UP + MODE Button ID SET ID:XXX Set ID by UP & DOWN button. 1~200. Confirm by SET button, then completed with beep. Table 12: Communication ID Setting Up to 200 LeakFilm Pro units can be connected to a LeakFilm MC using RS-485 communication. Each controller should have a unique communication ID which can be set using this menu. 23

24 7. Menu and Advanced Configuration Set Date and Time SET Button 3 seconds TIME SET Year:08 UP & DOWN then SET TIME SET Month:08 UP & DOWN TIME SET Min:08 Confirm by SET button, then completed with beep. Table 13: Date and time setting User can enter this menu by pushing the SET button for 3 seconds. Year, month, day, hour and minute can be set in this menu. Once the user pushes the SET menu after setting minute, date and time, setting is completed with a beep. Set buzzer alert option DOWN + MODE Button Buzzer ON Set On/Off by UP & DOWN button. Confirm by SET button, then completed with beep. Table 14: Buzzer alert option When this option is set to ON, the controller generate two beeps for leak and one beep for fault repeatedly. If it is set to OFF there will be no beep on the event. Default value is ON. Reset logging data Logged data in the controller can be reset by pushing SET and RESET button simultaneously. Set Log Clear Set + Reset Button 3 seconds LogClear

25 8. Characteristics and specifications LeakFilm Pro Item Specification Applicable sensor LeakFilm Conductive_D, LeakFilm Chemical Display 8x2 Character LCD / LED back light Power supply 20 to 36 VDC Power consumption Max 4 Watt LED indication Green - Power On Yellow - Service Red - Leak Sound level Over 10cm Output Relay (NC, NO)-24VDC 2A or 120 VAC 1A (Max. Switching voltage 60VDC or 240VAC) Communication RS485(*MODBUS ) Communication Function (Status transmission) Leak Detection Leak Location Leak Clearance Broken Detection Broken Clearance Data Logging 9 events - year / month / day / hour / min / Leak location Storage Temperature -10 to 65 C Operating Temperature -10 to 55 C Operating humidity 5 to 85 %RH Leak location accuracy ±1 m (up to 10 m) ID setting 1 to 200 IP rating IP20 EMC Directive 2004/108/EC EN /A1:2011, EN :2005, EN /A2:2009, EN :2008, Electrical Safety 1) Low Voltage Directive 2006/95/EC: EN :2010 2) US: UL rd Edition 3) Canada: CAN/CSA-C22.2 No rd Edition * To use the digital communication, please contact Honeywell Analytics Service Representative for further details. 25

26 LeakFilm Pro 9. Ordering Information Part number Product Name Description LeakFilm Controller HLFC1DRD LeakFilm Pro 1 Channel Conductive_D & Chemical Controller with Leak Location Detection LeakFilm Sensor HLFSSCND meter Conductive Sensor with Leak Position Detection HLFSSCND meter Conductive Sensor with Leak Position Detection LeakFilm Conductive_D Custom Length Conductive Sensor with Leak Position HLFSSCND-001 Detection HLFSSAND meter Chemical Sensor with Leak Position Detection HLFSSAND-050 LeakFilm Chemical 50 meter Chemical Sensor with Leak Position Detection HLFSSAND-001 Custom Length Chemical Sensor with Leak Position Detection LeakFilm Connector HLFNCSND-005 Start Connector Start Connector with 5 meter Lead Wire HLFNCJND-000 Cable Jump Connector with 15cm Lead Wire Jump Connector HLFNCJND-001 Cable Jump Connector with 1m Lead Wire HLFNCLND-000 Elbow Connector Elbow Connector HLFNCEND-000 End Connector 4 Lines End Connector 4 Lines with Leak Position Detection 26

27 10. Warranty Statement All products are designed and manufactured to the latest internationally recognised standards by Honeywell Analytics under a Quality Management system that is certified to ISO As such Honeywell Analytics warrants its products against defective parts and workmanship and will repair or (at its option) replace any instruments which are or may become defective under proper use within 18 months from date of commissioning by an approved Honeywell Analytics representative or 24 months from date of shipment from Honeywell Analytics, whichever is the sooner. This warranty does not cover disposable batteries or damage caused by accident, abuse, abnormal operating conditions or poisoning of sensor. Defective goods must be returned to Honeywell Analytics premises accompanied by a detailed description of any issue. Where return of goods is not practicable Honeywell Analytics reserves the right to charge for any site attendance where any fault is not found with the equipment. Honeywell Analytics shall not be liable for any loss or damage whatsoever or howsoever occasioned which may be a direct or indirect result of the use or operation of the Contract Goods by the Buyer or any Party. This warranty covers instrument and parts sold to the Buyer only by authorised distributors, dealers and representatives as appointed by Honeywell Analytics. The warranties set out in this clause are not pro rata, i.e. the initial warranty period is not extended by virtue of any works carried out there under. In no event will Honeywell Analytics be liable for any incidental damages, consequential damages, special damages, punitive damages, statutory damages, indirect damages, loss of profits, loss of revenues, or loss of use, even if informed of the possibility of such damages. Honeywell Analytic's liability for any claims arising out of or related to this product will in no case exceed the order value. To the extent permitted by applicable law, these limitations and exclusions will apply regardless of whether liability arises from breach of contract, warranty, tort (including but not limited to negligence), by operation of law, or otherwise. 27

28 11. Installation Drawing 28

29 11. Installation Drawing 29

30 Find out more Contact Honeywell Analytics: Europe, Middle East, Africa Life Safety Distribution AG Javastrasse Hegnau Switzerland Tel: +41 (0) Fax: +41 (0) gasdetection@honeywell.com Customer Service: Tel: (Freephone number) Tel: (Alternative number) Fax: Middle East Tel: (Fixed Gas Detection) Middle East Tel: (Portable Gas Detection) India Tel: Americas Honeywell Analytics Inc. 405 Barclay Blvd. Lincolnshire, IL USA Tel: Toll free: Fax: detectgas@honeywell.com Asia Pacific Honeywell Analytics Asia Pacific #701 Kolon Science Valley (1) 43 Digital-Ro 34-Gil, Guro-Gu Seoul Korea Tel: +82 (0) Fax: +82 (0) India Tel: analytics.ap@honeywell.com Please Note: While every effort has been made to ensure accuracy in this publication, no responsibility can be accepted for errors or omissions. Data may change, as well as legislation and you are strongly advised to obtain copies of the most recently issued regulations, standards and guidelines. This publication is not intended to form the basis of a contract. Technical Services EMEAI: HAexpert@honeywell.com US: ha.us.service@honeywell.com AP: ha.ap.service@honeywell.com Issue 2 04/2015 H_MAN0964_EMEA 3001M5002_2 ECO HAA Honeywell Analytics 13382