Infrared Ceiling Mount Sensor
|
|
- Loraine Poole
- 5 years ago
- Views:
Transcription
1 Infrared Ceiling Mount Sensor LOS-CI Series LOS-CI The LOS-CI Series ceiling-mount passive infrared sensors can integrate into Lutron systems or function as standalone controls using a Lutron power pack. The sensor uses a small semiconductor heat detector that resides behind a multi-zone optical lens. The sensor s detector is sensitive to the heat emitted by the human body. In order to trigger the sensor, the source of heat must move from one range of detection to another. Non-moving hot objects will not cause the lights to turn on. Features Intelligent, continually adapting passive infrared (PI) sensor Passive infrared sensing eliable motion detection with high error immunity Snap-locks to ceiling-mounted cover plate Non-Volatile Memory: settings saved in protected memory are not lost during power outages 50 to,500 sq.ft. coverage mounted on 8 ft. ceiling Affords choice of turning lights off or dimming to a preset level in the unoccupied state when integrated with a Lutron system. Models Available Cat. No. Color Coverage (sq.ft.) Field of View LOS-CI-50-WH White LOS-CI-500-WH White, Self-Adaptive Feature The LOS-CI Series ceiling-mount occupant sensors provides reliable detection with high error immunity. The internal microprocessor analyzes the information from the PI technology and determines the optimum setting to use in order to properly cover the space.
2 Specifications LOS-CI Series LOS-CI Timer Adjustment Automatic mode: Continually adapting sensor automatically adjusts settings to the space Manual mode: 8 to minutes Test mode: 8 seconds LED Lamp ed: infrared motion detected Housing ugged, high-impact, injection-molded plastic Color-coded leads 6 (6.cm) Operating voltage: 0- V, Class (PELV) low-voltage Operating current: ma nominal Control output: 0- V active high logic control signal with short-circuit protection, open collector when unoccupied UL and CUL listed Operating Environment Temperature: F to 0 F (0 C to 0 C) elative humidity: less than 95%, non-condensing For indoor use only Dimensions. (8).5 () Measurements are in inches (mm) Front View Side View
3 Wiring Single Sensor to System LOS-CI Series or More Sensors to System LOS-CI control system ed (+0- V ) (common) control system ed (+0- V ) (common) To additional sensors, maximum determined by lighting controller to Sensors with Pack 0/77/7 V 60 Hz; 0 V 50/60 Hz Hot Neutral ed (+0- V ) (common) Pack White ed ed Manual switch off (optional) Load Note: Maximum occupant sensors. Switching Multiple Loads with Auxiliary Packs Hot 0/77/ 7 V 60 Hz; Neutral 0 V 50/60 Hz Manual switch off (optional) Load ed ed Auxiliary Pack Note: Maximum of devices total (occupant sensors and auxiliary power packs) can be connected to a power pack. ed (+0- V ) (common) Pack White ed ed Load
4 LOS-CI Series LOS-CI Installation Sensor Placement The occupant sensor must have an unobstructed view of the room. Do not mount behind or near tall cabinets, shelves, indirect hanging fixtures, etc. Keep the occupant sensor away from air flow from ventilation outlets, windows, fans, etc. Closely follow the diagrams shown concerning major and minor motion coverage. The sensor can detect major motion (such as a person taking a half-step) at a greater distance than it can detect minor motion (such as writing or typing at a desk). May not detect occupancy with no significant difference between ambient and body temperatures. ange Diagrams 6.5 (.9) (.7) (.7) LOS-CI-50 (6.7) LOS-CI-500 Major motion detection Minor motion detection Dimensions are in feet (m).
5 Installation LOS-CI Series LOS-CI Mounting Normal Mounting Twist and lock threaded mounting post onto cover plate. Drill through ceiling tile with assembly, using cutter end of the threaded mounting post. Secure with washer and nut. Mounting to Non-Standard Ceiling or Fixture Mount twist-lock cover plate using mounting screws, nuts, and washers (included). Drill/punch wire routing hole through ceiling tile at center of cover plate. /6 () Cutter end Wire Lengths (feet) # Sensors # Aux. PPs AWG AWG AWG (.).5 (6) Mounting Plate Dimensions. (06.6) Measurements are in inches (mm) Using the Infrared Mask Typical Mask Patterns Conference oom Mask 80 Mask Full Mask Center Ceiling Mount (Mask blocks sensor seeing out doorway into hall) Corner Ceiling Mount (No mask needed) ectangular Areas Over the Door Specific Areas You Wish to Mask
6 LOS-CI Series LOS-CI Sensor Adjustments Override Settings Auto/Manual Threshold LED Motion Indicator eset Learned Settings A Off (Default) Automatic (Normal) Auto Threshold Adjustment Lights indicate motion etain Settings (Normal) On Manual on/off (Override) High Sensitivity (Low turn-on threshold) Disable LED Indicator Erase all learned settings, estart Learning (Toggle On) Strong Airflow Compensation Over Doorway Installation Timer Adjust Auto Sensitivity B Off On Disable Compensation (Normal) Enable Compensation No (Normal) Yes (Use increased turn-on threshold) Adjust Timer Automatically Use Manual Setting (No adjustment) Adjust Sensitivity Automatically Adjust Sensitivity Manually Timer Test Mode Factory Settings. emove the retainer cover.. otate the black timer adjustment knob to about midway ( o clock).. eturn setting to minimum setting (full CCW). ed: Infrared sensitivity 75% default : Timer 8 min. A B Factory Settings o clock Full CCW Note: The timer will remain in the 8-second test mode for hour, then automatically reset to 8 minutes.. To manually take the timer out of the 8-second test mode, turn the timer adjustment approximately /6 clockwise to make the setting slightly above minimum (just above the 8-minute setting).
Infrared Ceiling Mount Sensor
Infrared Ceiling Mount Sensor 69655c 0.07. The LOS-CIR Series passive infrared ceiling-mount sensors can integrate into LutronR systems or function as stand-alone controls using a LutronR power pack. The
More informationInfrared Wall Mount Occupancy Sensor
LOS-WI LOS-WI-1 02.01.06 Infrared Wall Mount Occupancy Sensor The LOS-WI wall-mounted passive infrared sensor is used in spaces with pendant fixtures, ceiling fans, or high ceilings (more than 12 feet).
More informationCeiling-Mounted Motion Detector. 752/CD, 752/CP, 752/CU and 752/Cx180. Installation Instructions
Ceiling-Mounted Motion Detector 752/CD, 752/CP, 752/CU and 752/Cx180 Installation Instructions Contents 1.0 Description...3 1.1 Contents of the Box...3 2.0 Safety...4 3.0 Coverage Patterns...4 3.1 PIR
More informationWireless Wall-Mount Sensor
Wireless Wall-Mount Sensor 369-268 1 06.29.10 Lutron wall-mounted occupancy and vacancy sensors are wireless battery-powered passive infrared (PIR) sensors that automatically control lights via RF communication
More informationDual Technology Wall Switch Occupancy Sensor. Manual & Specification
Dual Technology Wall Switch Occupancy Sensor Manual & Specification PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH LOCAL ELECTRICAL CODES Douglas Lighting Controls Page 1 November 19, 2014 1. INTRODUCTION
More informationPassive Infrared (PIR) Wall Switch Occupancy Sensor Dual Circuit
Instruction Bulletin 63249-420-418A1 02/2014 Passive Infrared (PIR) Wall Switch Occupancy Sensor Dual Circuit Commercial Grade with Ground SLSPWD1277C Retain for Future Use INTRODUCTION The Passive Infrared
More informationDual Technology Wall Mounted Occupancy Sensor. Manual & Specification
Dual Technology Wall Mounted Occupancy Sensor Manual & Specification PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH LOCAL ELECTRICAL CODES Douglas Lighting Controls Page 1 December 16, 2013 1. INTRODUCTION
More informationHUNTERSVILLE, NORTH CAROLINA USA EFFECTIVE SEPTEMBER 1, 2004
HUNTERSVILLE, NORTH CAROLINA USA EFFECTIVE SEPTEMBER 1, 2004 EPA Green Lights A L L Y USE OF THIS LOGO DOES NOT IMPLY EPA ENDORSEMENT APRIL 2008 www.nsiindustries.com E-mail: nsi@nsiindustries.com Fax:
More informationInstallation Instructions
DT-300 360 Dual Technology Low Voltage Occupancy Sensor with Light Level, Isolated Relay and Manual On features Specifications Voltage................18-28VDC/VAC, half wave rectified AC Current Consumption...............................43mA
More informationv3 360 Dual Technology Low Voltage Occupancy Sensor with Light Level, Isolated Relay and Manual On feature
DT-300 v3 360 Dual Technology Low Voltage Occupancy Sensor with Light Level, Isolated Relay and Manual On feature Specifications Voltage...18-28VDC/VAC, half wave rectified AC Current Consumption...25
More informationPSC-ID-x-CM Series Ceiling Mount Occupancy Sensor
TECHNICAL SPECIFICATIONS PSC-ID-x-CM Series Ceiling Mount Occupancy Sensor Basic Features Line voltage version: 120-277VAC, 60Hz Low voltage version: 24VDC, requires separate class 2 power supply PIR sensor
More information64.7 Ø85. (1) Sensor inset (2) Lens pluggable. (3) Protection cover (covers the high-voltage terminals). (4) Ceiling (drill hole Ø70mm).
Flush Mount PIR Motion Sensor PIR 1-10V Dimming with Remote Control Mechanical Structure 70mm 64.7 4 56 68.1 73.3 Ø85 3 (1) Sensor inset (2) Lens pluggable Infrared receiver 1 Photocell LED indicator (3)
More informationCeiling-Mounted Wireless Occupancy/Vacancy Sensor
Project name Prepared by Date INDOOR AIRLINK enabled by Lutron Catalog #: ALW OS/VS CM Part #: 624094 624615 The Ceiling-Mounted Wireless Occupancy & Vacancy Sensors are wireless, battery- powered, passive
More informationDS160/DS161 Request To Exit PIR sensors Installation Instructions
DS160/DS161 Request To Exit PIR sensors Installation Instructions 1.0 Description The DS160 is a Passive Infrared Detector (PIR) which is UL Listed as an Access Control Device under the UL 294 Standard.
More informationDS160/161 Request To Exit PIR sensors Installation Instructions
DS160/161 Request To Exit PIR sensors Installation Instructions 1.0 Description The DS160/161 is a passive-infrared (PIR) detector designed for request to exit (REX) interior applications. It is UL Listed
More informationInstallation Manual. Features SMART SWITCH OCCUPANCY SENSOR. Maximum Versatility. Maximum Energy Savings
Features SMART SWITCH OCCUPANCY SENSOR Installation Manual Maximum Energy Savings Maximum Versatility Sensitive 140 view passive infrared motion detector keeps lights on only when rooms are in use. Switches
More informationWireless Wall-Mount Sensor
Wireless Wall-Mount Sensor 369-481a 1 01.17.12 LutronR wall-mounted occupancy and vacancy sensors are wireless battery-powered passive infrared (PIR) sensors that automatically control lights via RF communication
More informationTOCR02 2 PART MICRO MOTION SENSOR W/IR REMOTE CONTROLLER
TOCR0 PART MICRO MOTION SENSOR W/IR REMOTE CONTROLLER SAFETY PRECAUTIONS Be sure to switch off power source before installing. Make sure that the power wiring comes from circuit with an external 16A miniature
More informationWireless Wall-Mount Sensor
Wireless Wall-Mount Sensor Lutron wall-mounted occupancy and vacancy sensors are wireless, battery-powered, passive infrared (PIR) sensors that automatically control lights via RF communication to compatible
More informationD-TECT Introduction. Connecting the Unit. Quick Installation. Multi Beam Alignment & Masking. Mounting the Unit
D-TECT 2 GJD300 Quad PIR Movement Detector Package Contents Package Contains: 1 x D-Tect 2 1 x Drilling template for fixing holes 3 x 31.75mm wall plugs 3 x 31.75mm screws 2 x Spare Sliding Curtains 2
More informationVESICA LINEAR SUSPENDED VES L
PROJECT INFORMATION Project Name Catalog # VESICA LINEAR SUSPENDED APPLICATIONS Office Spaces Conference Rooms Municipal Facilities Medical Facilities Type Date Financial Institutions Retail Spaces Hospitality
More informationCeiling Mount Sensors B4-B9. Occupancy and Vacancy Sensors B10-B15 B16-B17. Wall Mount Occupancy Sensors B-1
Occupancy and Vacancy Sensors ENERLITES offers a wide variety of lighting sensors. They are designed to bring convenience to your life and business while helping to reduce energy consumption in commercial,
More informationSensors and Detectors
12/12/2017 Sensors and Detectors - Clipsal by Schneider Electric Sensors and Detectors Add sensors and detectors to make an environment smarter and more efficient. C-Bus sensors and detectors allow environmental
More informationViveTM Basic Packages
ViveTM Basic Packages 369912a 1 11.10.15 The ViveTM Basic Package incorporates Maestro load controls and wireless sensors which provides a system that delivers energy savings, convenience, and ease of
More information180 Degree Ceiling Mounted Occupancy Sensors
Instruction Bulletin 63249-420-386A 2/202 80 Degree Ceiling Mounted Occupancy Sensors PS-CDS800 and PS-CUS800 INTRODUCTION The 80 Degree Ceiling Mount Occupancy Sensors are ideal for use in business and
More informationMini Product Guide.
Mini Product Guide www.acuitybrands.com/sensorswitch Better Performance Through Advanced Technology 100% Digital Passive Infrared (PIR) Detection Dual Technology Detection utilizing Microphonics Contractor
More informationDocument # R01
Viconics VT7600 Series PIR-Ready Rooftop Unit Controllers Part 1 General The VT7600 series is designed for single-stage and multi-stage control of heating/cooling equipment such as rooftop and self-contained
More informationLighting Control Strategies. to meet code requirements save energy and improve building performance
Lighting Control Strategies to meet code requirements save energy and improve building performance 1 Lighting Control Strategies Agenda Why Lighting Control Manual Light Reduction Scheduling Occupancy
More informationEver evolving energy code requirements and the large demand for energy
Ever evolving energy code requirements and the large demand for energy saving products have made lighting control sensors a must-have for building owners and managers. Hubbell Control Solutions introduces
More informationDS9370-BEL. Installation Instructions TriTech Ceiling Mount PIR/Microwave Intrusion Detector
DS970-BEL EN Installation Instructions TriTech Ceiling Mount PIR/Microwave Intrusion Detector DS970-BEL Installation Instructions.0 Installation Considerations.0 Installation Considerations Not suitable
More information, ,
796-2028, 796-2021, 796-2025 Batten mount PIR detectors Overview This series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual control
More informationLPCMPIRM65 & LPCMPIRDSI65
Product Guide LPCMPIRM65 & LPCMPIRDSI65 Luminaire high mount PIR detectors Overview The LPCMPIR PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationDual Relay Multi-Technology Wall Switch Occupancy Sensors
Dual Relay Multi-Technology Wall Switch Occupancy Sensors The OSSMD line of dual relay multi-technology Decora style wall switch occupancy sensors features several models to provide automatic lighting
More informationIP65 High Bay Dual Sense Sensor
IP65 High Bay Dual Sense Sensor TM and, 1-10V Dimming with Remote Control Technical Data Input Characteristics Sensor Data Model No. Model No. Mains voltage 220-240VAC 50/60Hz Sensor principle High Frequency
More informationPRODUCT DATA AND INSTALLATION SHEET MWS5-SA STAND ALONE MINIATURE CEILING MOUNTED MICROWAVE PRESENCE DETECTOR
8. SPECIFICATION LOAD 6 Amps fluorescent and incandescent lighting. 3 Amps compact fluorescent lighting. 3 Amps low energy lighting. 3 Amps low voltage lighting (switch primary of transformer). Switch
More informationInstallation Instructions
Specifications PW-100 PW-200 PW-100/PW-100-347/PW-200/PW-200-347 v3 Passive Infrared Wall Switch Occupancy Sensor PW-100-347 PW-200-347 Voltages: PW-100 & PW-200................ 120/277VAC, 50/60Hz PW-100-347
More informationOccupancy Sensor LS Descriptions. Product Profile. Technical Specifications
LS-818-3 Descriptions Temco s Passive Infrared Occupancy Sensor is a low cost comercial and residential surface mount occupancy sensor. Advanced filtering reduces false triggering due to air movement and
More informationPIR/INT & PIR/INT-D. Batten mount PIR detectors. Product Guide. Overview. Features
Product Guide PIR/INT & PIR/INT-D Batten mount PIR detectors Overview The PIR/INT & PIR/INT-D miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional
More informationCeiling PIR HS presence detector. Product Guide. Overview. Features
Product Guide 796-2047 Ceiling PIR HS presence detector Overview The 796-2047 (passive infrared) presence detector provides automatic control of lighting loads with optional manual control. This is a high
More informationSpecifications Occupancy/Vacancy Sensors CSI ASHRAE AIA Division 16 Section 16950
1 Specifications Occupancy/Vacancy Sensors CSI 26.09.23. ASHRAE 90.1-2010 AIA Division 16 Section 16950 1. PART 1 - General 1.1 Overview 1.1.1 Provide Occupancy/Vacancy sensors as shown on the plans and
More informationInstallation Instructions
HB-15NB High Bay Line Voltage Passive Infrared Occupancy Sensors with Nipple Backbox SPECIFICATIONS HB-15NB Power Module Voltages.............................12/277VAC, 6Hz Load Requirements @ 12VAC, 6Hz.............-8W
More informationCDR-AL Room CO 2 Traffic Light Alarm Units and Sensors
Product sheet SN1.402 Type CDR-AL CDR-AL Room CO 2 Traffic Light Alarm Units and Sensors CDR-AL sensors are designed to detect carbon dioxide concentration and temperature in the room spaces. The units
More informationMovement Detector GJD 300
Movement Detector GJD 300 Installation & Set Up Guide Introduction A CCTV event trigger utilising two independent passive infrared detectors combined in a T05 package. Both sensors have to trigger before
More informationMetalux SWLED LED. Type. Catalog # Project. Date. Comments. Prepared by
DESCRIPTION is a versatile LED surface or wall mount luminaire which can be used in a broad range of commercial and industrial applications. This series provides customers with a high quality luminaire
More informationDescription FEATURES. l Innovative dual mount system requires only one sensor for either flush or surface mount applications
Simple Fit Switching Sensors 1.8m to 3m Cone-shaped detection pattern, 6m radius at mounting height 6.0m AC220~240V/50Hz MK Simple Fit Sensors offer cost effective presence detection for lighting control
More informationIP65 High Bay Dual Sense Sensor
IP65 High Bay Dual Sense Sensor TM and, Daylight Harvest with Remote Control Technical Data Input Characteristics Sensor Data Model No. Model No. Mains voltage 220-240VAC 50/60Hz Sensor principle High
More informationMaestro Occupancy Sensing Switch
Maestro Occupancy Sensing Switch Lutron Maestro Occupancy Sensing switches with occupancy and vacancy sensors are lighting controls with passive infrared sensors that automatically control the lights in
More informationEBMPIR-MB. Batten mount PIR detectors. Product Guide. Overview. Features
Product Guide EBMPIR-MB Batten mount PIR detectors Overview The EBMPIR-MB series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual
More information2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T F E. cristalcontrols.
2025 Lavoisier, #135 Quebec, Quebec G1N 4L6 T. 418 681-9590 1 800 681-9590 F. 418 681-7393 E. info@cristalcontrols.com cristalcontrols.com TM Index Quick Selection...3-4 Which Technology to use...4 Retrofit
More informationTechnology. Occupancy & Vacancy Sensors & Timers. Technology. Occupancy & Vacancy Sensors & Timers L-2
Passive Infrared Sensors (PIR) Using a patented fresnel lens which minimizes optical aberrations, each Legrand/Pass & Seymour PIR sensor breaks its coverage area into zones. Upon detecting an infrared
More informationTable of Contents. Fast Fact. Sensor Models 2 Advantages of Sensors 3 FAQs 4-5
Sensor Buying Guide Table of Contents Sensor Models 2 Advantages of Sensors 3 FAQs 4-5 Occupancy and Vacancy Sensors, which provide automatic switching of lighting and motor loads, are fast becoming a
More informationFR-A180 FR-A360. Occupancy detector. Use
5 488 Occupancy detector with daylight sensor Occupancy detector with integral daylight sensor for demand-based control of HVAC systems and lighting. Adjustable switch-on and switch-off delay Adjustable
More informationTouch Screen Thermostat. MTSC/SUPER/CO2, MTSC24/SUPER/CO2 Series. MTS/SUPER/CO2, MTS24/SUPER/CO2 Series. Owner s manual and technician settings
Touch Screen Thermostat MTSC/SUPER/CO2, MTSC24/SUPER/CO2 Series MTS/SUPER/CO2, MTS24/SUPER/CO2 Series Owner s manual and technician settings Rev. 2.4 Index 1. Owner s Manual... 3 1.1 Quick Guide. 4 1.2
More informationCeiling PIR HS presence detector 1-10V, low temperature. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
Product Guide EBDHS-AD-LT30 Ceiling PIR HS presence detector 1-10V, low temperature Overview The EBDHS-AD-LT30 PIR (passive infrared) presence detector provides automatic control of lighting loads with
More informationTechnical Application Guide
Lighting Control Wireless Occupancy Sensor, Wireless Multi Sensor Technical Application Guide Philips wireless occupancy sensor and multi sensor, which are Interact Ready, mean easy upgrade to a smart
More information2000W PIR LIGHT CONTROLLER SLB2000-Black SLW2000-White INSTALLATION & OPERATING INSTRUCTIONS
2000W PIR LIGHT CONTROLLER SLB2000-Black SLW2000-White INSTALLATION & OPERATING INSTRUCTIONS SLB2000 PIR LIGHT CONTROLLER - BLACK WEATHERPROOF IP44 PIR SWITCHING 2000w MAXIMUM MANUAL ON/OFF OVERRIDE TIME
More informationViewguard Motion detctors PIR and DUAL detectors
Motion detctors and DUAL detectors Passive infrared sensor Passive infrared and microwave sensor AM DUAL AM DUAL Variations detectors: - AM /BUS-1 VdS Class C EN 5131-1 and EN 5131-2-2, grade 3 - /BUS-1
More informationD-Tect 2 GJD300 Quad PIR Movement Detector
D-Tect GJD0 Quad PIR Movement Detector Package Contents 3. Package Contains: x D-Tect x Drilling template for fixing holes x Allen Key 3 x 3.75mm wall plugs 3 x 3.75mm screws x Spare Sliding Curtains x
More informationTER Active Room Temperature Sensor (Controller),
Product sheet SN1.415 Type TER TER Active Room Temperature Sensors (Controllers) The TER active sensors are designed to detect temperature in the room spaces. The TER sensors have linear 0..10V signals
More informationLPC3BSP65 & LPC3BDP65
Product Guide LPC3BSP65 & LPC3BDP65 Batten mount PIR detectors Overview The LPC3B series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional
More informationLUX Hardwired - Installation Notes
Ness LUX wired PIR with Nightlight Quad element pyro sensor 15m x 15m wide angle coverage Look down Creep Zone Selectable Standard and Pet Aware modes Adjustable sensor mask for No Creep and Pet modes
More informationModel: MLSA360N. Installation & Operating Instructions. 360º Night Eye PIR Light Controller
Model: MLSA360N Installation & Operating Instructions 360º Night Eye PIR Light Controller Motion Sensor Detection Perspective View 5 metre 1 Ceiling Mount Position 0º Sensor Tilt Up 3º 3º 5 metre Sensor
More informationDimmer/Switch with Occupancy and Vacancy Sensor
369-270a 1 07.21.10 Maestro Sensors Lutron s Maestro Dimmer and with occupancy and vacancy sensors are lighting controls with passive infrared sensors that automatically control the lights in an area.
More information0 C to 50 C ( 32 F to 122 F ) 0% to 95% R.H. non-condensing. 30 to 95% R.H. Dry contact across terminal BI1, BI2 & UI3 to Scom
Viconics VT7350 Series PIR Ready Fan-coil Controllers General The VT7350 series are PIR Ready low-voltage microprocessor-based fan-coil controllers. Models are available controlling single speed and multi-speed
More informationVive PowPak Fixture Controls
Vive 369918g 1 03.12.18 The PowPak wireless fixture control is a radio-frequency (RF) device that controls either the Lutron EcoSystem or 0 10 V- electronic fluorescent ballasts and LED drivers (depending
More informationENERGY EFFICIENCY EXPERTS
ENERGY EFFICIENCY EXPERTS Sensors maximize energy savings by ensuring that lights are turned off or to a lower level when spaces are unoccupied or adequate daylight exists. WattStopper s sensors provide
More informationApollo Intelligent Auto Aligning Beam Detector. User Guide
Apollo Intelligent Auto Aligning Beam Detector User Guide EN 1. General Information 50cm 50cm 8-100m Ensure clear line of sight from Detector to Reflector Mount on solid surfaces (structural wall or girder)
More informationFalse Ceiling HF Sensors
False Ceiling HF Sensors HC009S/EXT HC018V/EXT HC019V/EXT Applications Ideally suited to retrofit projects where the luminaire is too small to accomodate the sensor internally, this motion sensor can be
More informationMaestro Occupancy Sensor C L Dimmer
Maestro Occupancy Sensor C L Dimmer Lutron Maestro occupancy sensor C L dimmers are lighting controls with passive infrared sensors that automatically control the lights in an area. These sensors detect
More informationPhone-A-Stat. MODEL Command Center With Thermostat Operation, Maintenance & Installation Manual. Introduction.
Introduction The UL listed Phone-A-Stat (model # 7632 ) is designed and approved for the safe operation of remotely controlling four independent loads, such as a sprinkler system or a water heater via
More informationTri-level Control HF Sensor
Tri-level Control HF Sensor Standard Version Applications Occupancy detector with tri-level control suitable for indoor use. Suitable for building into the fixture: Office / Commercial Lighting Use for
More information0ACDT2000MV Ultasonic/Infared Occ Sensor
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 0ACDT2000MV Ultasonic/Infared Occ Sensor Eaton Lighting Catalog Number 0ACDT2000MV Manufacturer Eaton Lighting Description
More informationCS1200 WHT Pir Ceiling Mount Occupancy Sensor
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 Catalog Number Manufacturer Description Weight per unit Product Category Features Area Coverage Field of View Load Type
More informationUltrasonic Wall Switch Occupancy Sensor Single Circuit
Instruction Bulletin 63249-420-414A1 02/2014 Ultrasonic Wall Switch Occupancy Sensor Single Circuit Commercial Grade with Ground, Single and Multi Location Switching SLSUWS1277C and SLSUWS3277C Retain
More informationMaestro Dual-Circuit Occupancy Sensing Switch
Dual-Circuit Switch with Occupancy/Partial-On Maestro Dual-Circuit Occupancy Sensing Switch The Lutron Maestro Dual-Circuit Occupancy Sensing Switch combines two switches with an in-wall, passive infrared
More informationPassive Infrared Motion Detector 5420/90P. Installation Instructions
Passive Infrared Motion Detector Installation Instructions 5420/90P The 5420/90P Passive Infrared Motion Detector provides reliable, high performance detection at an affordable price. The Detector features
More informationdesign guide for wireless l i g h t i n g c o n t r o l
design guide for wireless l i g h t i n g c o n t r o l ON OFF system operation radiotouch Fluorescent Fixtures ( With Lutron dimming ballasts) Power RadioTouch Controller RadioTouch Controller Power Power
More information360º Surface Mount Ceiling PIR Light Controller
360º Surface Mount Ceiling PIR Light Controller Model: PDRS1500 Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference
More informationMWS5. Miniature Microwave Presence Detector (standalone) Product Guide. Overview. Features
Product Guide MWS5 Miniature Microwave Presence Detector (standalone) Overview The MWS5 series of miniature microwave presence detectors provide automatic control of lighting loads with optional manual
More informationNational Grid Small Business Program Rebate Manual
National Grid Small Business Program Rebate Manual Rebate Manual Munro Distributing has prepared this manual to aid you and your clients in taking advantage of available rebate programs offered by National
More information60W Multi PIR Bulkhead
60W Multi PIR Bulkhead Model: MLB98 Black Installation & Operating Instructions 1. General information: The unit utilises passive infrared technology to detect heat radiation of moving human bodies. Upon
More informationFor assistance with the product please contact: HELPLINE. For a product brochure please contact:
For assistance with the product please contact: HELPLINE 020 8450 0515 or email helpline@timeguard.com For a product brochure please contact: Timeguard Limited. Victory Park, 400 Edgware Road, London NW2
More informationTebis application software
5 Tebis application software STCC530E 2-channel presence detector 360 A faire Product reference Description TP device RF devices TCC530E Bi-zone presence detector TCC530E Output module: Dimmer Loads connected
More informationIntegrated SensorDIM LED Driver Daylight Monitoring Version
TM Integrated SensorDIM ED Driver Daylight Monitoring Version Model: HEC730 with HRC-0.1 ED + ED - ED current selection 0 9 Daylight threshold Antenna module connector Buzzer ] PUSH Extended antenna 99
More informationTri-level Control Sensor
Daylight Monitoring Photocell Advance TM One-Key Commissioning Ambient daylight threshold oop in oop out Tri-level Control Sensor HC038V HCD038 Detached inear Version with Remote Control Applications Occupancy
More informationIntegrated PIR detectors
EBMINT - Product Guide Integrated PIR detectors Overview The EBMINT series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual control
More informationUP 258E11 OPTISENS OFFICE
Product and functional description The UP 258E11 is a presence/motion detector with integrated 2-point light control. The UP 258E11 device communicates via KNX/EIB with actuators or other KNX devices.
More informationSENSA MRE DDM MR
96239831 SENSA MRE DDM MR Contents Section Contents Page 1 Dimensional information 1 2 Description and operation 2 3 Wiring and fixing 3 4 Programming 6 5 Wiring diagrams 8 6 Detection pattern diagrams
More informationMaestro Occupancy Sensing Switch
Maestro Sensing Switch Lutron Maestro Sensing switches with occupancy and vacancy sensors are lighting controls with passive infrared sensors that automatically control the lights in an area. These sensors
More informationµdim Microwave Sensors User Manual
Microwave Sensors User Manual P e o p l e I n n o v a t i o n s S o l u t i o n s 1. Introduction µdim Table of Contents Page Introduction 2 Technical data 3 Dimensions and mounting options 9 Connections
More informationIMPORTANT. PLEASE NOTE: The infrared beam path MUST be kept clear of obstructions at all times!
USER GUIDE English IMPORTANT PLEASE NOTE: The infrared beam path MUST be kept clear of obstructions at all times! Failure to comply may result in the Detector initiating a Fire or Fault signal. Contents
More informationMaestro 0 10 V Dimmer Sensor
NEW Maestro 0 10 V Dimmer Sensor Setting the new standard for 0 10 V control 0 10 V Dimmer Sinking control for 0 10 V fluorescent and LED fixtures Passive Infrared (PIR) Sensor Fine motion detection with
More informationBuilt-in HF Sensor for High Bay
Daylight Monitoring RX TM Synchronisation control Ambient daylight threshold Built-in HF Sensor for High Bay HC419VRC/R Tri-level Control With Synchronisation and Remote Control Applications Occupancy
More informationD-TECT Dual Tech. GJD360 Triple Technology External Detector
D-TECT Dual Tech GJD360 Triple Technology External Detector PACKAGE CONTENTS 1 x Dual Tech 1 x Drilling template for fixing holes 3 x 31.75mm wall plugs 3 x 31.75mm screws 2 x Spare Sliding Curtains 2
More informationWelcome. Sensor. 1 (844) LIGHTCLOUD Custom manufactured in China RAB Lighting, Inc 170 Ludlow Avenue Northvale, NJ 07647
Lightcloud is a commercial wireless lighting control system & service. It s powerful and flexible, yet easy to use and install. Learn more at lightcloud.com 1 (844) LIGHTCLOUD 1 (844) 544-4825 support@lightcloud.com
More informationTouch Screen Thermostat. MTSC/SUPER, MTSC24/SUPER Series. MTS/SUPER, MTS24/SUPER Series. Owner s manual and technician settings
Touch Screen Thermostat MTSC/SUPER, MTSC24/SUPER Series MTS/SUPER, MTS24/SUPER Series Owner s manual and technician settings -2 - Index 1. Owner s Manual... 4 1.1 Quick Guide. 4 1.2 Turning the unit ON
More informationLEVEL SWITCH NP-3T DL v1.0 Installation instructions Order no E-no
LEVEL SWITCH v1. Installation instructions Order no. 13181 E-no. 13 6 81 Control that uses a light sensor Presence Power regulating up to two hours No presence Low level Blue knob1% Rest No presence Completely
More informationWireless Occupancy Sensor, Ceiling Mount (WOS2-CM)
21233 Wireless Occupancy Sensor, Ceiling Mount Installation Instructions The Daintree Networks ceiling mounted Wireless Occupancy Sensor operates seamlessly within the ControlScope Manager (CSM), the Daintree
More informationDescription of the application programme for KNX occupancy detectors version 3.1
Contents 1. General...1 1.1 Basics for the KNX/EIB BUS...1 1.2 Application versions...1 1.2 Application versions Switchgear application Version 3.1: BEG_SWI_HKL_V3.1 Part numbers: 1.3 Symbols used...1
More information