TOCR02 2 PART MICRO MOTION SENSOR W/IR REMOTE CONTROLLER
|
|
- Alicia Banks
- 5 years ago
- Views:
Transcription
1 TOCR0 PART MICRO MOTION SENSOR W/IR REMOTE CONTROLLER SAFETY PRECAUTIONS Be sure to switch off power source before installing. Make sure that the power wiring comes from circuit with an external 16A miniature circuit breaker for the short circuit protection or a suitable fuse. The unit is designed to be mounted on the ceiling. (FIGURE 1) Power Circuit Part PIR Motion Sensor INTRODUCTION The use of occupancy detectors in commercial and industrial applications can significantly reduce energy usage reducing both energy costs and helping the environment. The Titan 360 degrees MICROSENSITIVE PART flush mount OCCUPANCY DETECTOR uses passive infrared sensors (PIR) which react to changes in temperature emitted by the slight motion of persons or objects passing through its detection area. The PIR sensor automatically operates the connected load when an area is occupied. After a preset time on non-activation (when an area is vacated) the load will be switched off. In addition the built in photocell takes natural light (daylight) into account when determining its activation.. It also incorporates lux memory feature which means the sensor is able to record and memorize the lux level when the internal connected light fixture is turned on by the Micro Motion Sensor. However, once the natural light lux level is higher than that of the internal artificial light even if the movement still exists, the sensor will switch off the internal light fixture thus saving energy. The product also incorporates a part structure allowing the initial installation to be made and the detector removed to avoid damage during painting, maintenance etc. FIGURE 1 The installation of this device should be made by a qualified electrician. OOSING A MOUNTING LOCATION Avoid aiming the motion sensor at heating vents, air conditioners or objects which may change temperature rapidly. Prior to mounting the light fixture, remember to position the motion sensor so that a moving object cuts across its beams, not directly towards them. (FIGURE ) FIGURE Note: Micro motion detection can be made within a radius of 3m around the sensor; regular motion detection can be made within a radius of 6m around the sensor. INSTALLATION A drill and a screwdriver are needed for installation. Select a location for the unit based on the coverage angles shown in FIGURE 3. The product is also supplied with a two channel Infra Red remote control for remote operation. Note: Read this entire manual before you start to install the system. 1
2 FIGURE 3 WIRING INSTRUCTION (1) Switch off the power source or wall switch. () Using a flat blade screwdriver to detach the PIR motion sensor and power circuit part. (FIGURE 4) FIGURE 5b Note: A pulse switch (S,S4) is connectable to the unit, enabling manual operation. (4) A 60mm hole should be drilled in the ceiling, put the power circuit to the hole and secure it using to the mounting surface using the screws provided. Fix the PIR motion sensor to the power circuit part by simply clicking in place (FIGURE 6). FIGURE 4 (3) When connecting to one Micro Motion Sensor, the wiring connection is shown hereunder: (FIGURE 5a) FIGURE 6 SETTING THE LIGHTING SYSTEM Please test the motion sensor function before testing the IR Remote Controller. Test Mode : Turn the LUX control and the TIME control anti clockwise the TEST position. (FIGURE 7) FIGURE 5a By connecting to two Micro Motion Sensors, the wiring connection is indicated as below: (FIGURE 5b) FIGURE 7 Turn on the wall switch. The light will turn on for about one minute to warm up. During warm-up
3 period, the light turns on continuously. After one minute is expired, the light will turn off. Walk through the detection area, the light will turn on continuously. If and when movement is ceased, the light will be on for one second before turning off. (1) TIME ADJUSTMENT E53R IR Remote Controller The TIME adjustment controls how long the light will stay on after the last motion has been detected. Time setting is adjustable from 5 seconds to 1 minutes. (FIGURE 8) FIGURE 10 ABOUT 5 SECONDS ABOUT 1 MINUTES FIGURE 8 Note: T serves as a short-time impulse, which allows you to control automatic switching of staircase lighting or timer. () LUX ADJUSTMENT The LUX adjustment determines at what light level the lighting system will start operating when you set the sensor to automatic operation. 3-button and channel selection slide switch are shown on the front cabinet as follows: (FIGURE 10) AUTO ON OFF ANNEL SWIT LOADING THE BATTERY (1) Use a flat blade screwdriver to detach the battery cover from the cabinet. (FIGURE 11) Provisionally turn the LUX control knob clockwise to the moon (dusk) position (FIGURE 9). Turn the LUX control knob slowly anti-clockwise until the light comes on. In this provisional setting mode, the motion sensor remains inactive during daylight. At dusk when you find it is the LUX level desired for operation, simply set the LUX control knob to the position which becomes active as daylight declines. The light turns on when you move and turns off when you stop. Wait for the light to turn off before moving again to test the sensor. FIGURE 9 (3) ANNEL SELECTION To avoid radio signal interference, and operate separate banks of detectors on a single remote, you are able to select different channels through channel switch. Select channel 1 or on the sensor for grouping the connected light fixtures in the same or different zone. FIGURE 11 () Insert a 1V alkaline battery to the battery compartment and refit the battery cover. (FIGURE 1) 3
4 1 OPERATION FIGURE 1 (3) OFF By pressing Off button to deactivate the light from illumination. User can also set the motion sensor back to Auto operation by pressing Auto button on the IR Remote Controller. (4) MANUAL OPERATION By using IR Remote Controller to your NL5703, you can easily select three modes of operation: automatic, on and off. Make sure the Micro Motion Sensor and IR Remote Controller are set at the same channel. (FIGURE 13a & 13b) By using pulse switch to manually control the connected light fixture to be turned on or off. If the connected light fixture has been turned on, simply press the pulse switch to turn off. If and when it has been turned off, press the pulse switch to turn on and the connected light fixture will be turned off automatically according to the time setting. (5) LUX MEMORY OFF ON AUTO 1 1 Under auto mode, the Micro Motion Sensor is triggered either by movement or by pressing the pulse switch, the sensor will automatically record and memorize its initial lux level. When the ambient lux level is 1.5 times higher than that of initial lux level, the sensor will switch off the connected light fixture to save energy. This feature is valid subject to the TIME setting being fixed more than one minute. It is irrelevant to lux adjustment. OFF ON AUTO 1 FIGURE 13a & 13b (1) AUTOMATIC OPERATION Before operating the IR Remote Controller, please make sure the sensor is in proper setting for Auto mode. The sensor detects motion automatically according to its time and lux setting. () ON To keep the light on regardless of motion, you can press On button on the IR Remote Controller. The light will be continuously on. The LED inside the sensor will light up when receiving IR Remote Controller s signal. SPECIFICATIONS Power Requirement AC 0 ~ 40V / 50Hz Operating Load (maximum) Max. 000W Incandescent or 1500W fluorescent Up to 10w LED (dimmable recommended) Detection Angle Up to 360 at 0 C Detection Range (Micro Movement) 3~4m radius at 0 C Detection Range (Regular Movement) 6~8m radius at 0 C Mounting Height Recommended.5~3.5m Ceiling Mount IR Controller Channel 1 & Auto / On / Off IR Controller Range 8M OPEN SPACE IR Controller Battery 3A 1V Wall switch control ON/OFF Pulse switch control ON/OFF Time Adjustment Adjustable 5 seconds ~ 1 minutes Lux Adjustment Yes Lux Memory Yes Warm Up Time About 1 min. Protection Class II *Specifications are subject to change without notice. A R01 4
5 Warning: Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. 5
PMCSF6 OCCUPANCY SENSOR
PMCSF6 OCCUPANCY SENSOR Lens Main Body Power Cord INTRODUCTION The use of occupancy detectors in commercial and industrial applications can significantly reduce energy usage lessening both energy costs
More information64.7 Ø85. (1) Sensor inset (2) Lens pluggable. (3) Protection cover (covers the high-voltage terminals). (4) Ceiling (drill hole Ø70mm).
Flush Mount PIR Motion Sensor PIR 1-10V Dimming with Remote Control Mechanical Structure 70mm 64.7 4 56 68.1 73.3 Ø85 3 (1) Sensor inset (2) Lens pluggable Infrared receiver 1 Photocell LED indicator (3)
More informationCeiling PIR HS presence detector 1-10V, low temperature. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
Product Guide EBDHS-AD-LT30 Ceiling PIR HS presence detector 1-10V, low temperature Overview The EBDHS-AD-LT30 PIR (passive infrared) presence detector provides automatic control of lighting loads with
More informationCeiling PIR HS presence detector. Product Guide. Overview. Features
Product Guide 796-2047 Ceiling PIR HS presence detector Overview The 796-2047 (passive infrared) presence detector provides automatic control of lighting loads with optional manual control. This is a high
More informationDual Technology Wall Mounted Occupancy Sensor. Manual & Specification
Dual Technology Wall Mounted Occupancy Sensor Manual & Specification PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH LOCAL ELECTRICAL CODES Douglas Lighting Controls Page 1 December 16, 2013 1. INTRODUCTION
More informationLPC3BSP65 & LPC3BDP65
Product Guide LPC3BSP65 & LPC3BDP65 Batten mount PIR detectors Overview The LPC3B series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional
More information30W LED PIR FLOODLIGHT. Model: LEDX30PIRB Model: LEDX30PIRWH
30W LED PIR FLOODLIGHT Model: LEDX30PIRB Model: LEDX30PIRWH 1. Designated Use LEDX30PIR is an outdoor motion detector for automatic LED lighting control. Mainly for wall installation. Simple plug in wall
More information, ,
796-2028, 796-2021, 796-2025 Batten mount PIR detectors Overview This series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual control
More informationCeiling PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. PIR Sensor.
Product Guide EBDSM-DD Ceiling PIR presence detector DALI / DSI dimming Overview The EBDSM-DD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationLPCMPIRM65 & LPCMPIRDSI65
Product Guide LPCMPIRM65 & LPCMPIRDSI65 Luminaire high mount PIR detectors Overview The LPCMPIR PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationDETECTOR TRANSMITTER INSTALLATION & OPERATING. Cat No. TLTX2000B INSTRUCTIONS
DETECTOR TRANSMITTER Cat No. TLTX2000B INSTALLATION & OPERATING INSTRUCTIONS 1 Introduction The TLTX2000B Controller Transmitter is part of the Timeguard range of PIR products which communicate by radio
More informationPIR/INT & PIR/INT-D. Batten mount PIR detectors. Product Guide. Overview. Features
Product Guide PIR/INT & PIR/INT-D Batten mount PIR detectors Overview The PIR/INT & PIR/INT-D miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional
More information360º Surface Mount Ceiling PIR Light Controller
360º Surface Mount Ceiling PIR Light Controller Model: PDRS1500 Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference
More informationEBDHS-DD-LT30. Ceiling PIR HS presence detector DALI / DSI, low temperature. Product Guide. Overview. Features
EBDHS-DD-LT30 Product Guide Ceiling PIR HS presence detector DALI / DSI, low temperature Overview The EBDHS-DD-LT30 PIR (passive infrared) presence detector provides automatic control of lighting loads
More informationModel: MLSA360N. Installation & Operating Instructions. 360º Night Eye PIR Light Controller
Model: MLSA360N Installation & Operating Instructions 360º Night Eye PIR Light Controller Motion Sensor Detection Perspective View 5 metre 1 Ceiling Mount Position 0º Sensor Tilt Up 3º 3º 5 metre Sensor
More informationII SL. Installation Guide. VOLTEX IMS64-2 Dual output indoor flush mount PIR motion detector IMS64-2
II112918-SL Installation Guide VOLTEX IMS64-2 Dual output indoor flush mount PIR motion detector IMS64-2 TECHNICAL DATA Rated voltage: 220V-240V~ 50/60Hz Load: Load 1( /T1) for Lighting Incandescent: Max.
More informationFor assistance with the product please contact: HELPLINE. For a product brochure please contact:
For assistance with the product please contact: HELPLINE 020 8450 0515 or email helpline@timeguard.com For a product brochure please contact: Timeguard Limited. Victory Park, 400 Edgware Road, London NW2
More informationHigh bay PIR presence detector 1-10V dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
Product Guide EBDSPIR-HB-AD High bay PIR presence detector 1-10V dimming Overview The EBDSPIR-HB-AD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationPSC-ID-x-CM Series Ceiling Mount Occupancy Sensor
TECHNICAL SPECIFICATIONS PSC-ID-x-CM Series Ceiling Mount Occupancy Sensor Basic Features Line voltage version: 120-277VAC, 60Hz Low voltage version: 24VDC, requires separate class 2 power supply PIR sensor
More informationHSD-200Z Z-Wave Motion Sensor
HSD-200Z Z-Wave Motion Sensor The HSD-200Z is a Z-Wave TM enabled device and is fully compatible with any Z-Wave TM enabled network. Z-Wave TM enabled devices displaying the Z-Wave TM logo can also be
More information2000W PIR LIGHT CONTROLLER SLB2000-Black SLW2000-White INSTALLATION & OPERATING INSTRUCTIONS
2000W PIR LIGHT CONTROLLER SLB2000-Black SLW2000-White INSTALLATION & OPERATING INSTRUCTIONS SLB2000 PIR LIGHT CONTROLLER - BLACK WEATHERPROOF IP44 PIR SWITCHING 2000w MAXIMUM MANUAL ON/OFF OVERRIDE TIME
More informationEBMPIR-MB. Batten mount PIR detectors. Product Guide. Overview. Features
Product Guide EBMPIR-MB Batten mount PIR detectors Overview The EBMPIR-MB series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual
More informationMWS3A-PRM Product Guide
MWS3A-PRM Product Guide Microwave Presence/Absence Detector Contents Section Contents Page 1 Dimensional information 1 2 Description and operation 2 3 Wiring & Installation 3 4 Fixing - Flush 4 5 Fixing
More information60W Multi PIR Bulkhead
60W Multi PIR Bulkhead Model: MLB98 Black Installation & Operating Instructions 1. General information: The unit utilises passive infrared technology to detect heat radiation of moving human bodies. Upon
More informationProduct Guide. Ceiling PIR HS presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs.
PPAD-C-HB-DALI-230V Product Guide Ceiling PIR HS presence detector DALI / DSI dimming Overview The PPAD-C-HB-DALI-230V PIR (passive infrared) presence detector provides automatic control of lighting loads
More informationSENSA MRE DDM MR
96239831 SENSA MRE DDM MR Contents Section Contents Page 1 Dimensional information 1 2 Description and operation 2 3 Wiring and fixing 3 4 Programming 6 5 Wiring diagrams 8 6 Detection pattern diagrams
More information3. Proper use. 4. Function. 1. Product characteristics. 2. Safety. Function description. Channel A light. Motion detector
307021 3. Proper use EN Motion detector themova P360-100 UP WH 1030600 themova P360-100 UP GR 1030601 The motion detector is intended for interior. The motion detector is eclusively intended for the use
More information360º FLUSH MOUNT CEILING PIR LIGHT CONTROLLER INSTALLATION & OPERATING. Cat No. SLFM360 INSTRUCTIONS
360º FLUSH MOUNT CEILING PIR LIGHT CONTROLLER Cat No. SLFM360 INSTALLATION & OPERATING INSTRUCTIONS 1 Introduction The SLFM360 utilises passive infrared technology to detect heat radiation of moving human
More informationMWS3A-PRM. Ceiling microwave presence/absence detector. Product Guide. Overview. Features
Product Guide MWS3A-PRM Ceiling microwave presence/absence detector Overview The MWS3A-PRM microwave presence detector provides automatic control of lighting loads with optional manual control. The MWS3A-PRM
More information5W LED Energy Saver PIR Bulkhead
5W LED Energy Saver PIR Bulkhead Model: LED88PIR Black Installation & Operating Instructions 1. General information: The unit utilises passive infrared technology to detect heat radiation of moving human
More informationPRODUCT DATA AND INSTALLATION SHEET MWS5-SA STAND ALONE MINIATURE CEILING MOUNTED MICROWAVE PRESENCE DETECTOR
8. SPECIFICATION LOAD 6 Amps fluorescent and incandescent lighting. 3 Amps compact fluorescent lighting. 3 Amps low energy lighting. 3 Amps low voltage lighting (switch primary of transformer). Switch
More informationHigh bay PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
EBDSPIR-HB-DD Product Guide High bay PIR presence detector DALI / DSI dimming Overview The EBDSPIR-HB-DD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional
More informationSensors Explained AUTOMATION
Sensors Explained Sensors Explained: Our range of PIR sensors and microwave presence detectors are designed to reduce the amount of time lighting is left on unnecessarily, for example if an area is unoccupied
More informationIntegrated PIR detectors
EBMINT - Product Guide Integrated PIR detectors Overview The EBMINT series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual control
More informationMotion detector themova P360 KNX UP WH themova P360 KNX UP GR
307079 EN Motion detector themova P360 KNX UP WH 1039600 themova P360 KNX UP GR 1039601 1. Product characteristics 4 2. Safety 5 3. Proper use 6 4. Function 6 5. Detection area 10 6. Installation 13 7.
More informationPPAD-C-230V. Ceiling PIR presence/absence detector. Product Guide. Overview. Features
Product Guide PPAD-C-230V Ceiling PIR presence/absence detector Overview The PPAD-C-230V passive infrared presence detector provides automatic control of lighting loads with optional manual control. The
More informationFor assistance with the product please contact: HELPLINE. For a product brochure please contact:
For assistance with the product please contact: HELPLINE 020 8450 0515 or email helpline@timeguard.com For a product brochure please contact: Timeguard Limited. Victory Park, 400 Edgware Road, London NW2
More informationLUX Hardwired - Installation Notes
Ness LUX wired PIR with Nightlight Quad element pyro sensor 15m x 15m wide angle coverage Look down Creep Zone Selectable Standard and Pet Aware modes Adjustable sensor mask for No Creep and Pet modes
More informationVITMR-EBDSPIR-PRM. PIR Presence/Absence Detector IR with Ceiling Rose. Product Guide. Overview. Features
Product Guide VITMR-EBDSPIR-PRM PIR Presence/Absence Detector IR with Ceiling Rose Overview The VITMR-EBDSPIR-PRM PIR (passive infrared) presence detector provides automatic control of lighting loads.
More informationDual Technology Wall Switch Occupancy Sensor. Manual & Specification
Dual Technology Wall Switch Occupancy Sensor Manual & Specification PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH LOCAL ELECTRICAL CODES Douglas Lighting Controls Page 1 November 19, 2014 1. INTRODUCTION
More informationSWITCHLITE MRE SLD MAN SWITCHLITE MRE SLD IP55
96239823 SWITCHLITE MRE SLD MAN 96239821 SWITCHLITE MRE SLD IP55 Overview The SWITCHLITE MRE SLD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationProduct Guide. Ceiling microwave presence detector DALI / DSI. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MPAD-C-DALI-230V Product Guide Ceiling microwave presence detector DALI / DSI Overview The MPAD-C-DALI-230V microwave presence detector provides automatic control of lighting loads with optional manual
More informationSWITCHLITE MRE SLDM ADJ
96239855 SWITCHLITE MRE SLDM ADJ Contents Section Contents Page 1 Dimensional information 1 2 Description and operation 2 3 Wiring & Installation 3 4 Fixing - Flush 4 5 Fixing - Surface 4 6 Head locking
More informationMWS6-PRM. Ceiling microwave presence/absence detector. Product Guide. Overview. Features
Product Guide MWS6-PRM Ceiling microwave presence/absence detector Overview The MWS6-PRM microwave presence detector provides automatic control of lighting loads with optional manual control. The MWS6-PRM
More information1. Product characteristics 4 2. Safety 5 3. Proper use 5 4. Operation 6
307214 1103107701 EN Presence detector theronda S360-101 DE WH 2080565 theronda S360-101 DE GR 2080566 theronda S360-101 AP WH 2080555 theronda S360-101 AP GR 2080556 1. Product characteristics 4 2. Safety
More informationSECURITY LIGHT MODEL NO: CL6PIR OPERATION INSTRUCTIONS PART NO: GC0215
SECURITY LIGHT MODEL NO: CL6PIR PART NO: 4003535 OPERATION INSTRUCTIONS GC0215 INTRODUCTION Thank you for purchasing this CLARKE Security Light with motion sensor. The motion sensor is a small electronic
More informationIP65 High Bay Dual Sense Sensor
IP65 High Bay Dual Sense Sensor TM and, 1-10V Dimming with Remote Control Technical Data Input Characteristics Sensor Data Model No. Model No. Mains voltage 220-240VAC 50/60Hz Sensor principle High Frequency
More informationModel: PDFM1500. Installation & Operating Instructions 360º Flush Mount Ceiling PIR Light Controller
Model: PDFM1500 Installation & Operating Instructions 360º Flush Mount Ceiling PIR Light Controller can cause to your immediateneighbours.light pollution caused by incorrectly installing a unit or over-lighting
More informationCompact Movement Activated Sensor Installation Instructions
MAL540 Instructs. 12/7/06 3:43 PM Page 3 Compact Movement Activated Sensor Installation Instructions MAL540 series 2 Where to fit your Security Sensor To achieve best results for outside use the Arlec
More informationSensors and Detectors
12/12/2017 Sensors and Detectors - Clipsal by Schneider Electric Sensors and Detectors Add sensors and detectors to make an environment smarter and more efficient. C-Bus sensors and detectors allow environmental
More informationDetailed operating instructions
MA00613903 Detailed operating instructions MD 360/8 Basic EB10430404 MD 360i/8 Basic EB10430428 MD 360/24 Basic EB10430848 MD 360i/24 Basic EB10430862 MD 360/8 Basic SMB EB10430497 MD 360i/8 Basic SMB
More informationProduct Guide. Ceiling PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs.
Product Guide LPCMPIRDSI Ceiling PIR presence detector DALI / DSI dimming Overview The LPCMPIRDSI PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More information18W Round LED Wall/Ceiling Light with Microwave Sensor
18W Round LED Wall/Ceiling Light with Microwave Sensor Model: LEDMR18WHMS Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further
More informationDetailed operating instructions
MA00744002 Detailed operating instructions MD-FLAT 360i/8 RW EP10427886 MD-FLAT 360i/8 SW EP10427893 MD-FLAT 360i/8 RB EP10428074 MD-FLAT 360i/8 SB EP10428081 MD-FLAT-E 360i/8 RW GST EP10427862 MD-FLAT-E
More informationMWS5. Miniature Microwave Presence Detector (standalone) Product Guide. Overview. Features
Product Guide MWS5 Miniature Microwave Presence Detector (standalone) Overview The MWS5 series of miniature microwave presence detectors provide automatic control of lighting loads with optional manual
More informationIP65 High Bay Dual Sense Sensor
IP65 High Bay Dual Sense Sensor TM and, Daylight Harvest with Remote Control Technical Data Input Characteristics Sensor Data Model No. Model No. Mains voltage 220-240VAC 50/60Hz Sensor principle High
More information3. Intended use. 4. Function. 1. Product characteristics. 2. Safety. Functional description. Channel A light. Motion detector
EN Motion detector themova S360-101 DE WH 1030565 themova S360-101 DE GR 1030566 themova S360-101 AP WH 1030555 themova S360-101 AP GR 1030556 1. Product characteristics 307067 Passive infra-red motion
More informationEBDSPIR-PRM-VFC & EBDSPIR-PRM-VFC-NC
Product Guide EBDSPIR-PRM-VFC & EBDSPIR-PRM-VFC-NC Ceiling PIR presence/absence detector Overview The EBDSPIR-PRM-VFC PIR (passive infrared) presence detector provides automatic control of lighting loads
More informationAnalogue Dimming Microwave Presence/Absence Detector
Product Guide MWS3A-AD Analogue Dimming Microwave Presence/Absence Detector Contents Section Contents Page 1 Dimensional information 1 2 Description and operation 2 3 Wiring & Fixing 3 4 Installation 3
More informationHigh Frequency Sensor
Model: HF1 Installation & Operating Instructions High Frequency Sensor 1. Specifications: 1. Power: AC 220 ~ 240V 50MHz. 2. Sensor Technology: 5.8GHz High Frequency. 3. Switching capacity: 1000W Incandescent
More informationµdim Microwave Sensors User Manual
Microwave Sensors User Manual P e o p l e I n n o v a t i o n s S o l u t i o n s 1. Introduction µdim Table of Contents Page Introduction 2 Technical data 3 Dimensions and mounting options 9 Connections
More informationUser Manual 120/240/300 Outdoor Motion Detector
User Manual 120/240/300 Outdoor Motion Detector Swiss Garde 4000 Warning! - Any work on the main power supply must only be completed by trained specialists. - The product must be installed in accordance
More informationThe Power To Supply... All Your Electrical Products
May 2016 ENERGY EFFICIENT RETROFIT SOLUTIONS The Power To Supply... All Your Electrical Products www.cef.co.uk All products are subject to availability and are correct at the time of print. Errors and
More informationSurface Mount Wall PIR Light Controller. Model: PDWM1500. Installation & Operating Instructions
Surface Mount Wall PIR Light Controller Model: PDWM1500 Installation & Operating Instructions 1. Introduction The PDWM1500 utilises passive infrared technology to detect heat radiation of moving human
More information360 Surface Mount Ceiling PIR Light Controller
360 Surface Mount Ceiling PIR Light Controller Model: SLW360L Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference
More information1. Basic safety information 3 2. Proper use 3
310481 01 EN Motion detectors theluxa P220 WH 1010605 theluxa P220 BK 1010606 theluxa P300 WH 1010610 theluxa P300 BK 1010611 1. Basic safety information 3 2. Proper use 3 Disposal 3 3. Description 4 4.
More informationEBMHS (standard & slim-line PSU)
Product Guide EBMHS (standard & slim-line PSU) Miniature HS PIR Presence Detector (luminaire fitting) Overview The EBMHS series of miniature PIR (passive infrared) presence detectors provide automatic
More informationKingShield. - Occupancy Detectors NEW. For complete Lighting Control... ORION RANGE. P High performance for optimum switching of all types
ORION RANGE KingShield - Occupancy Detectors P High performance for optimum switching of all types of lighting - including P Extensive product range P For domestic and commercial applications NEW PRODUCT
More informationSimple Instructions for the WisePIR
Simple Instructions for the WisePIR General Description of use. INSTALLATION 2 Channel movement detector for use with Wise Control Radio Receivers. Note: The WisePIR will send a programming signal for
More informationWireless Occupancy Sensor, Ceiling Mount (WOS2-CM)
21233 Wireless Occupancy Sensor, Ceiling Mount Installation Instructions The Daintree Networks ceiling mounted Wireless Occupancy Sensor operates seamlessly within the ControlScope Manager (CSM), the Daintree
More informationLUCCI AIRFUSION BREEZE WALL FAN INSTALLATION OPERATION MAINTENANCE WARRANTY INFORMATION CAUTION READ INSTRUCTIONS CAREFULLY FOR SAFE
LUCCI AIRFUSION BREEZE WALL FAN INSTALLATION OPERATION MAINTENANCE WARRANTY INFORMATION CAUTION READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION. V1.0- E N ( 0 8 / 2 0 1 8 ) THANK YOU
More informationTable of Contents. Fast Fact. Sensor Models 2 Advantages of Sensors 3 FAQs 4-5
Sensor Buying Guide Table of Contents Sensor Models 2 Advantages of Sensors 3 FAQs 4-5 Occupancy and Vacancy Sensors, which provide automatic switching of lighting and motor loads, are fast becoming a
More informationModel: PDSM1500. Installation & Operating Instructions 360º Surface Mount Ceiling PIR Light Controller
Model: PDSM1500 Installation & Operating Instructions 360º Surface Mount Ceiling PIR Light Controller Considerate Lighting pollution bythe incorrectly installing a unit an or area Please be caused aware
More information12W Round LED Wall/Ceiling Light with Microwave Sensor
12W Round LED Wall/Ceiling Light with Microwave Sensor Model: LEDSR12WHMS Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further
More informationDirect Dim Microwave Presence/Absence Detector
Product Guide MWS3A-DD Direct Dim Microwave Presence/Absence Detector Contents Section Contents Page 1 Dimensional information 1 2 Description and operation 2 3 Wiring & Fixing 3 4 Installation 3 5 Fixing
More informationGI1DPC/B User Guide. Mains tungsten GLS filament or halogen lamp Min 60W Max 300W. Linear fluorescent
GI1DPC/B User Guide Single gang PIR Dimmer Replaces a standard light switch or dimmer Turns off automatically Turns on automatically Security mode Night light mode* Scene setting and soft on/off* * only
More informationThe Power To Supply... All Your Electrical Products
ENERGY EFFICIENT RETROFIT SOLUTIONS The Power To Supply... All Your Electrical Products www.cef.co.uk All products are subject to availability and are correct at the time of print. Errors and omissions
More informationCeiling Microwave presence detector - DALI / DSI 12-24V AC/DC. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MWS6-DD-LV Product Guide Ceiling Microwave presence detector - DALI / DSI 12-24V AC/DC Overview The MWS6-DD-LV microwave presence detector provides automatic control of lighting loads with optional manual
More informationThe most user friendly Security Alarm System L S Section 1 Overview of System Section 2 Planning your Installation
The most user friendly Contents Section 1 Overview of System 1.1 Kit Contents 1.2 Tools Required 1.3 System Features Security Alarm System L S 4 0 0 Section 2 Planning your Installation 2.1 Location of
More informationEBDSPIR-PRM-2CH, EBDSPIR-PRM-2CH-NC
Product Guide EBDSPIR-PRM-2CH, EBDSPIR-PRM-2CH-NC Ceiling PIR presence/absence detector 2 channel Overview The EBDSPIR-PRM-2CH PIR (passive infrared) presence detector provides automatic control of lighting
More informationBATTERY POWERED DETECTOR/ TRANSMITTER INSTALLATION & OPERATING. Cat No. TLTXDCB INSTRUCTIONS
BATTERY POWERED DETECTOR/ TRANSMITTER Cat No. TLTXDCB INSTALLATION & OPERATING INSTRUCTIONS 1 Introduction The TLTXDCB Battery Powered Detector/Transmitter is part of the Timeguard range of PIR products
More informationProduct Guide. Ceiling microwave presence detector DALI / DSI. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MPAD-C-A-DALI-230V Product Guide Ceiling microwave presence detector DALI / DSI Overview The MPAD-C-A-DALI-230V microwave presence detector provides automatic control of lighting loads with optional manual
More informationPRODUCT INFORMATION. Uses tough, high quality PC diffuser, resistant to fracture and to ultraviolet light to limit discolouring.
Ø297mm Packing list in Ceiling Mount Lamp LEDS 96PCS Φ6 Wall plug 3x30 Screw Φ3 Sealing ring 4x12 Y type Stainless Screw Quantity 1X 4X 4X 3X 3X PRODUCT INFORMATION 98.5mm Ideal for energy saving this
More informationLS800S Intruder Alarm System. Engineering Manual
LS800S Intruder Alarm System Engineering Manual Table of Contents Section 1 Overview of System 1.1 Kit Contents 1.2 Tools Required 1.3 System Features Section 2 Planning your installation 2.1 Location
More informationInfrared Ceiling Mount Sensor
Infrared Ceiling Mount Sensor LOS-CI Series LOS-CI- 0.0.06 The LOS-CI Series ceiling-mount passive infrared sensors can integrate into Lutron systems or function as standalone controls using a Lutron power
More informationSWITCHLITE MRE DDM ADJ
96239889 SWITCHLITE MRE DDM ADJ Front features Mounting Bezel Back features Retaining Spring Power Input & Switched Output Connector (Channel 1) Sensor Lens which covers... Microwave Sensor IR Receiver
More informationLUCCI AIRFUSION QUEST II CEILING FAN
LUCCI AIRFUSION QUEST II CEILING FAN WITH IR REMOTE INSTALLATION OPERATION MAINTENANCE WARRANTY INFORMATION CAUTION READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION. V1.0 QUEST II IR
More informationLantern Receiver E-997 INSTALLER GUIDE. SF-LA-BC-RX-W.qxd 13/04/ :36 Page 1
SF-LA-BC-RX-W.qxd 13/04/2005 13:36 Page 1 Lantern Receiver E-997 INSTALLER GUIDE V1.0-04/05 IQLA-BC-RX-W IQ Europe Limited Sandbeck Lane, Wetherby LS22 7TW. Visit us at www.iq-europe.co.uk Installation
More information2. Safety. 1. Product characteristics. 3. Proper use. 4. Operation. Function description. Presence detector
EN Presence detector theprema P360-101 E UP WH 2070105 theprema P360-101 E UP GR 2070106 1. Product characteristics 307175 1103087101 Passive infrared presence detector for ceiling installation Square
More informationIP 55 (category II) IP 54 (category II) 4. Connection. 1. Basic safety information. 2. Proper use. 5. Installation. 3. Description.
EN Motion detectors theluxa P0 WH 0 theluxa P0 BK 0 theluxa P00 WH theluxa P00 BK. Basic safety information WARNING anger of death through electric shock or fire! ¾Installation should only be carried out
More informationWireless Occupancy Sensor, Wall Mount with Photosensor (WOS2-WM)
Installation Instructions The Daintree wall mounted Wireless Occupancy Sensor (WOS2-WM) operates seamlessly within the Daintree wireless lighting control platform. The WOS2-WM is a battery-powered occupancy
More informationDetector switch - Dual Tech
Page 1. Use.................................... 1 2. Technical characteristics................1 3. Dimensions............................ 2 4. Connection........................... 2 5. Installation...........................
More informationCeiling Microwave presence detector - DALI / DSI 12-24V AC/DC. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MWS3A-DD-LV Product Guide Ceiling Microwave presence detector - DALI / DSI 12-24V AC/DC Overview The MWS3A-DD-LV microwave presence detector provides automatic control of lighting loads with optional manual
More informationCeiling-Mounted Wireless Occupancy/Vacancy Sensor
Project name Prepared by Date INDOOR AIRLINK enabled by Lutron Catalog #: ALW OS/VS CM Part #: 624094 624615 The Ceiling-Mounted Wireless Occupancy & Vacancy Sensors are wireless, battery- powered, passive
More information360 Ceiling PIR Light Controller
360 Ceiling PIR Light Controller Model: SLFM360L Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference and maintenance.
More informationFR-A180 FR-A360. Occupancy detector. Use
5 488 Occupancy detector with daylight sensor Occupancy detector with integral daylight sensor for demand-based control of HVAC systems and lighting. Adjustable switch-on and switch-off delay Adjustable
More informationInstallation Manual. Features SMART SWITCH OCCUPANCY SENSOR. Maximum Versatility. Maximum Energy Savings
Features SMART SWITCH OCCUPANCY SENSOR Installation Manual Maximum Energy Savings Maximum Versatility Sensitive 140 view passive infrared motion detector keeps lights on only when rooms are in use. Switches
More informationMotion Sensor. Specifications
Used for motion activated and dusk to dawn lighting control of flood lights, area lights, etc. Durable weatherproof construction utilizing infrared technology to sense temperature changes caused by movement
More informationEBDSPIR-PRM-LV Product Guide
EBDSPIR-PRM-LV Product Guide Ceiling PIR presence/absence detector 12-24V AC/DC Overview The EBDSPIR-PRM-LV PIR (passive infrared) presence detector provides automatic control of low voltage loads including
More information