RA889A Switching Relay
|
|
- Stewart Phillips
- 5 years ago
- Views:
Transcription
1 Switching Relay INSTALLATION INSTRUTIONS APPLIATION The Switching Relay provides intermediate switching of line- and low-voltage devices from a line- or low-voltage controller and is typically applied in hydronic heating systems. 5 (9) (0) () SPEIFIATIONS Electrical Ratings: Voltage: 0 Vac, 60 Hz. Thermostat Heat Anticipator Setting: 0.A. () DIAMETER () DIAMETER () DIAMETER KEYHOLE TYPE MOUNTING HOLE Transformer Ratings: Primary: 0 Vac, 60 Hz. Secondary: Vac, VA maximum; 9 VA available for external loads. Secondary is protected by replaceable A automotive fuse. ontact Ratings: 5 AFL, 0 ALR; maximum connected load 000 VA. () 5 () Switching Action: Spdt, plus extra low voltage Spst. Electrical onnections: No. captivated wire clamp screw terminals. Dimensions: See Fig.. ross Reference: The replaces many Honeywell models. See Table for additional cross reference information. (9) (6) DIAMETER MOUNTING HOLE (0) () (0) 5 6 (5) Replacement Parts: Replacement Fuse: Use a A automotive fuse. 5 (0) KNOKOUT FOR (5) / () ONDUIT () MA Fig.. dimensions in in. (mm). U.S. Registered Trademark opyright 999 Honeywell Inc. All Rights Reserved X-XX UL 69-9-
2 SWITHING RELAY Table. Replacement ross Reference. onnections Manufacturer Model Input Line Voltage Power Relay Low Voltage Relay Thermostat omments Honeywell L N.. X X Honeywell RA9Ab T T Honeywell RA b B R See Fig. thermostat connections. Jumper L to and between X and in. Honeywell RB 6 B R Requires jumper between X and Honeywell Ra 6 B R Honeywell RB 6 Jumper to. Line voltage switched inputs go to L and. Honeywell R a 6 See Fig. B. Honeywell RJa 6 Line voltage inputs go to L and. See Fig. B. Honeywell RA b W B Honeywell RB 6 W B Honeywell R a 6 W B Honeywell RJ a 6 a has one set of / relay contacts. Use R5U if two sets are required. b has lower output load rating. heck load requirements. INSTALLATION When Installing this Product.... Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition.. heck the ratings given in the instructions and on the product to make sure the product is suitable for your application.. Installer must be a trained, experienced service technician.. After installation is complete, check out product operation as provided in these instructions. 5. Follow local codes for installation and application. WARNING Electrocution Hazard. Power supply can cause severe injury, or death. Transformer core not bonded. Disconnect power supply before wiring. MOUNTING In replacement applications, mount the new relay in the same location as the old relay. For new installations, locate the relay vertically on a solid wall or partition as close as possible to the device to be controlled. Select a location that is easily accessible for installation and service. NOTE: To reduce the possible transformer hum and relay noise that is sometimes amplified by mounting surfaces such as sheetmetal, plasterboard, and similar materials, place rubber or felt washers between the case and the mounting surface.. Position the relay and mark the mounting holes. See Fig... Start a screw in the upper right corner for the keyhole type mounting hole. Screw it down within about / in. ( mm) of the surface.. Hang the relay on the screw, position the case, and start the bottom screw.. Tighten both screws. 69-9
3 SWITHING RELAY WIRING AUTION Electrical Shock or Personal Injury Hazard. Power supply can shock. Use only NE lass wire for all line voltage wiring connections. lass wires must be rated for at least 6 F (5 ). All wiring must comply with all applicable electrical codes, ordinances, and regulations. Follow all instructions furnished with the controlled equipment. IMPORTANT The switching relay terminals are approved only for use with copper wires. When two or more line-voltage load devices are to be controlled in parallel, the total current must not exceed the rating for the relay load. Never connect load terminals to a load that uses more current than the amount listed in the electrical ratings on the relay. See Table for wiring length specifications. See the schematic and typical hookups in Fig. through. AUTOMOTIVE FUSE G (LASS ) -WIRE Table. Wire Lengths. Wire Size Total Wire Length Wire Length of Run to Thermostat (AWG) Ft M Ft M L RELAY LED N.. X X L HOT TO POWER LOAD TO POWER LOW-VOLTAGE POWERPILE POWER SUPPLY. PROVIDE OVERLOAD PROTETION AND DISONNET MEANS AS REQUIRED. M95 Fig.. internal schematic and typical hookup. TF TF TF RELAY L X X L X X L X X L (HOT) PUMP PUMP PUMP G L T T B B LA/LA 55 RG F F T T ORANGE WHITE BLAK BURNER AND IGNITION POWER SUPPLY. PROVIDE DISONNET MEANS AND OVERLOAD PROTETION AS REQUIRED. ONTROL ASE MUST BE ONNETED TO EARTH GROUND. USE GROUNDING SREW PROVIDED. B IS / IN. TAB TERMINAL. M0 Fig.. hookup for LA/LA in an oil-fired, tankless hot water, zoned, pump system. 69-9
4 SWITHING RELAY TF TF TF RELAY L X X L X X L X X L (HOT) PUMP PUMP PUMP G L T T B B LF/LE TR THTR TH GAS VALVE (eg, VR00) POWER SUPPLY. PROVIDE DISONNET MEANS AND OVERLOAD PROTETION AS REQUIRED. ONTROL ASE MUST BE ONNETED TO EARTH GROUND. USE GROUNDING SREW PROVIDED. B IS / IN. TAB TERMINAL. M Fig.. hookup for LF/LE in a gas-fired, V, zoned, pump system. ZONE ZONE ZONE ZONE R R W R W R W R W R A B 0 VA H H ZONE ZONE ZONE ZONE L L L Z G L (HOT) IRULATOR PUMP IRULATOR PUMP IRULATOR PUMP IRULATOR PUMP L X X G IRULATOR PUMP 5 ZONE 5 Z H H TO APPROPRIATE ONNETIONS AS REQUIRED BY THE SYSTEM. H-H TYPIALLY ONNETED TO T-T OF BURNER ONTROL SYSTEM. ONTROL ASE MUST BE ONNETED TO EARTH GROUND. USE GROUNDING SREW PROVIDED. USE OPPER ONDUTORS ONLY. FOR ALL LASS ONNETIONS, USE WIRE RATED FOR AT LEAST 6 F (5 ). POWER SUPPLY. PROVIDE DISONNET MEANS AND OVERLOAD PROTETION AS REQUIRED. ONNET L-Z JUMPER, IF REQUIRED. M Fig. 5. R zone expansion using additional Switching Relays. 69-9
5 SWITHING RELAY THREE-WIRE (SERIES 0) B X X X X TWO-WIRE (SERIES 0) MAKES ONTAT ONLY ON TEMPERATURE FALL. M6 Fig. 6. thermostat connections. A. FOR V ONTROL L, (HOT) NEUTRAL LINE VOLTAGE ONTROLLED OUTPUTS L N.. X X OPTIONAL R W ONTROLLED OUTPUT HEKOUT. Keep the cover on the relay during normal operation and remove only for service and checkout.. Relay contacts require no cleaning; they are arranged to close with a wiping action and are selfcleaning. The contacts may turn black after being in service for some time; this discoloration does not prevent proper operation.. After installation is complete, operate system through at least one cycle from the controller to make certain the relay controls the equipment as intended. TROUBLESHOOTING Test Button This connection is the same as a call for heat connection between the and terminals. Relay LED This LED lights whenever there is 0 Vac (L) on the terminal (when / relay contacts are closed). B. FOR LINE VOLTAGE ONTROL LINE VOLTAGE ONTROL NEUTRAL L JUMPER N.. X X. FOR EXTERNAL SEPARATE POWER SOURE NEUTRAL L V ONTROLLER INPUT SUPPLY N.. X X REQUIRED FOR OUTPUT LED OPERATION. FOR SERIES 0 OR OTHER HARDWIRED ELETRONI -WIRE S. WARNING! ELETROUTION HAZARD. POWER SUPPLY AN AUSE SEVERE INJURY OR DEATH. DISONNET POWER BEFORE WIRING OR SERVIING L. POWERED RELAYS MUST BE WIRED AS DRY ONTATS. M Fig.. control options
6 SWITHING RELAY Automation and ontrol Solutions Honeywell International Inc. 95 Douglas Drive North Golden Valley, MN 55 Honeywell Limited-Honeywell Limitée 5 Dynamic Drive Scarborough, Ontario MV Z G.R. Rev customer.honeywell.com
RA889A Switching Relay
Switching Relay FEATURES PRODUT DATA High load switching capability. Troubleshooting LED. Push-to-test button. Replaceable transformer fuse. Long-life D relay drive control technology. Relay for use with
More informationR8845U Universal Switching Relay
Universal Switching Relay PPLIION he Universal Switching Relay provides intermediate switching of line- and low-voltage devices from a line- or low-voltage controller. he may be used to replace several
More informationT834C Heating-Cooling Thermostat
M3375 M3375 TRADELINE T834C Heating-Cooling Thermostat Application T834C Thermostats control 4 to 30 Vac single-stage heating-cooling systems. See Table for specific models and applications. An spdt mercury
More informationT8090A/Q682B Heating, Cooling, and Heating-Cooling Thermostat, Wallplate and Subbase
M75 M75 T8090A/Q68B Heating, ooling, and Heating-ooling Thermostat, allplate and Subbase SUPER TRADELINE Installation Instructions for the Trained Service Technician. Preparation heck thermostat and subbase
More informationT8411R Electronic Heat Pump Thermostat
T84R Electronic Heat Pump Thermostat INSTALLATION INSTRUCTIONS The T84R Heat Pump Thermostat provides 24V control of two-stage heating and one-stage cooling heat pump system with manual changeover from
More informationC7232A,B Sensor and Controller CARBON DIOXIDE SENSOR
C7232A,B Sensor and Controller CARBON DIOXIDE SENSOR PRODUCT DATA C7232A C7232B FEATURES Used for CO 2 based ventilation control. Models available with LCD that provides sensor readings and status information.
More informationThe T6140A,B Remote Bulb Temperature Controller
T640A,B Remote Bulb Temperature Controller The T640A,B Remote Bulb Temperature Controller is used as a unit mount temperature controller in electric heat, fan coil, room air conditioner applications, cold
More informationT7079A,B Solid State Remote Temperature Controllers
T7079A,B Solid State Remote Temperature Controllers FEATURES PRODUCT DATA Switch selection of heat or cool mode. Temperature sensing up to 400 feet. Does not require field calibration. 0K NTC temperature
More informationARM SERIES Switching Relays With Priority
Models ARM-2P ARM-3P ARM-4P ARM-6P AD-1 AD-4 ARM SERIES Switching Relays With Priority INSTALLATION, OPERATION & MAINTENANCE MANUAL ARM-2P ARM-4P AD-1 ARM-3P ARM-6P AD-4 Information and specifications
More informationQ7800H Integrated Burner Control Subpanel
Q7800H Integrated Burner Control Subpanel INSTALLATION INSTRUCTIONS FEATURES Unique subpanel design eliminates extensive wiring in the OEM control panel. One subpanel design covers multiple applications.
More informationAR861-2II AR822-II AR861-3II. ARGO (Technical Support) 2201 Dwyer Avenue Utica, NY 13501
ARGO (Technical Support) 2201 Dwyer Avenue Utica, NY 13501 AR822-II AR861-2II AR861-3II (Corporate Sales) 85 Middle Road Dunkirk, NY 14048 www.argoindustries.com An ISO 9001-2000 Certified Company P/N
More informationT8400C and T8401C Electronic Thermostats
T8400 and T840 Electronic Thermostats INSTALLATION INSTUTIONS The T8400 and T840 Thermostats provide singlestage, non-programmable temperature control for 4V heating-cooling systems with manual changeover
More informationCR Series Command Relays
CR Series Command Relays FEATURES INSTALLATION INSTRUCTIONS Patented 35mm Din-rail mounting flange (US Patent 7,416,421) SPDT Form 1C Relay contacts Pilot duty rated LED status indication Stackable for
More informationT8190A/191108AJ Heating or Cooling Thermostat/Wallplate; T8190A/Q682B Heating/Cooling Thermostat/Subbase
M3375 M3375 T890A/908AJ Heating or Cooling Thermostat/Wallplate; T890A/Q68B Heating/Cooling Thermostat/Subbase Installation Instructions for the Trained Service Technician. Preparation NOTE: Order Q68B
More informationYP7999A1000 ControLinks Fuel Air Ratio Control Panel
YP7999A1000 ControLinks Fuel Air Ratio Control Panel FEATURES INSTALLATION INSTRUCTIONS Pre-wired and ready to install Includes the R7999A control, wiring subbase and S7999D1048 touchscreen display Commission,
More informationT4398A,B Precision Electric Heating Thermostat
T398A,B Precision Electric Heating Thermostat FEATURES PRODUCT DATA APPLICATION The T398 Electric Heating Thermostat provides precise, accurate line voltage control of electric heating equipment. A snap
More informationC554A Cadmium Sulfide Flame Detector
C554A Cadmium Sulfide Flame Detector FEATURES PRODUCT DATA Cadmium sulfide sensing element provides faster response than bimetal sensors. On flame failure, the cad cell causes the oil primary control to
More informationT874 Multistage Thermostat and Q674 Subbase
SUPER TRADELINE T874 Multistage Thermostat and Q674 Subbase Application The T874D Thermostat and Q674E Subbase provide 4 to 30 Vac control of standard stage heating and stage cooling systems. The Y594D
More informationIS Series Pressure Sensing Switches
IS Series Pressure Sensing Switches FEATURES INSTALLATION INSTRUCTIONS IS3 PRESSURE SWITCH APPLICATION IS2 PRESSURE SWITCH The IS Series of pressure sensing switches offers the same proven compression
More informationT4398A,B High Performance Electric Heat Thermostats
T498A,B High Performance Electric Heat Thermostats FEATURES PRODUCT DATA Controls both fan-forced and baseboard electric heaters. Temperature-responsive, vapor-filled dual diaphragm sensing element provides
More informationHYDRO-AIR ZONING CONTROLS ARH-1, ARH-2, ARH-3
HYDRO-AIR ZONING CONTROLS ARH-1, ARH-2, ARH-3 INSTALLATION, OPERATION & MAINTENANCE MANUAL ARH-1 ARH-2 ARH-3 ARGO 2201 Dwyer Avenue Utica, NY 13501 www.argocontrols.com An ISO 9001-2000 Certified Company
More informationINSTALLATION AND OPERATION INSTRUCTIONS 303, 304, 305, CRH, CRQ, CFA SERIES 2250 WATT MODELS
INSTALLATION AND OPERATION INSTRUTIONS 303, 304, 305, RH, RQ, FA SERIES 2250 WATT MODELS aution: To prevent electric shock disconnect power to heater at main service before wiring or service. aution: Do
More informationHYDRO-AIR ZONING CONTROLS ARH-1, ARH-2, ARH-3
HYDRO-AIR ZONING CONTROLS ARH-1, ARH-2, ARH-3 INSTALLATION, OPERATION & MAINTENANCE MANUAL ARH-1 ARH-2 Manufactured by: ECR International, Inc. 2201 Dwyer Avenue, Utica NY 13501 web site: www.ecrinternational.com
More informationL8005A,B; LS8005A,C,D Electronic Pool and Spa Controllers
Electronic Pool and Spa Controllers The L8005A,B and LS8005A,C,D Electronic Pool and Spa Controllers are used in pool, spa, and hot tub applications to control water temperature. Remote Potentiometer L8005A,B
More informationL8151A Triple Aquastat Relay
L85A riple Aquastat Relay he L85A is a remote bulb controller for use with hydronic heating systems that include domestic hot water service. Provides high limit, low limit, and circulator control for maintaining
More informationDeluxe Programmable Thermostats
Deluxe mable Thermostats T8602D INSTALLATION INSTRUCTIONS APPLICATION The T8602D IV Deluxe mable Thermostat provides electronic control of 24 Vac single-stage heating and cooling systems or 750 mv heating
More informationT6984F,G Electronic Floating Control Thermostats
T6984F,G Electronic Floating Control Thermostats FEATURES PRODUCT DATA P+I control action provides accurate, stable room temperature control. Used with ML644 Series 60 Direct Coupled Damper Actuators.
More informationR8182D,E,F,H,J Combination Protectorelay Primary Control and Aquastat Controller
R88D,E,F,H,J Combination Protectorelay Primary Control and Aquastat Controller APPLICAION he R88 combines a Protectorelay primary control and immersion type Aquastat controller in one unit for use in oil-fired,
More informationCommercial/Industrial Combustion Control Level Three Announcement
Commercial/Industrial Combustion Control Level Three Announcement SUBJECT: C6097 requiring venting Model Numbers Affected: C6097A and B Ref. Number L3-08-006 Issue Date 12/9/08 Author P.Yuen/L.Ziller Date
More informationAQ475A Aquatrol Outdoor Temperature Compensator for Boilers
A Aquatrol Temperature Compensator for s Features PRODUCT DATA Adjustable settings for boiler maximum temperature, boiler minimum temperature and outdoor low (design) temperature. Selectable Warm Weather
More informationSLATE. Burner Control Module INSTALLATION INSTRUCTIONS R8001B2001
SLATE Burner Control Module R8001B2001 INSTALLATION INSTRUCTIONS Scan for more information Application SLATE brings configurable safety and programmable logic together into one single platform. The platform
More informationT8602C Chronotherm IV Deluxe Programmable Thermostats
T8602C Chronotherm IV Deluxe mable Thermostats INSTALLATION INSTRUCTIONS APPLICATION The T8602 Chronotherm IV Deluxe mable Thermostat provides electronic control of 24 Vac single-stage heating and cooling
More informationPS914 Power Supply. 900-KL Keylock (optional) Page BB Battery Backup (optional) Page 3
F1! DANGER 44487056 These instructions cover the following parts: PS914 Power Supply Installation Instructions! DANGER: To avoid risk of electric shock, turn off A power before installing or servicing
More informationDeluxe Programmable Heat Pump Thermostat T8611M
APPLICATION Deluxe mable Heat Pump Thermostat T8611M INSTALLATION INSTRUCTIONS The T8611M Deluxe mable Heat Pump Thermostat provides electronic control of 24 Vac single-zone two compressor or two speed
More informationT7984 A,B,C Electronic Modulating Control Thermostats
T7984 A,B,C Electronic Modulating Control Thermostats FEATURES PRODUCT DATA APPLICATION These microprocessor-based thermostats provide proportional - integral (PI) individual room temperature control in
More informationT4098A,B Deluxe Electric Heat Thermostats
T4098A,B Deluxe Electric Heat Thermostats FEATURES PRODUCT DATA Controls both fan-forced and baseboard electric heaters. Temperature-responsive, vapor-filled dual diaphragm sensing element provides 2 F
More information7800 SERIES RM7888A Relay Module
7800 SERIES RM7888A Relay Module FEATURES SPECIFICATION DATA APPLICATION The Honeywell RM7888A Relay Module is a microprocessor-based integrated burner control for industrial process semi-automatically
More informationT4031A,B,P; T6031A,B Refrigeration Temperature Controllers
T4031A,B,P; T6031A,B Refrigeration Temperature Controllers FEATURES PRODUCT DATA Wide control temperature range is suitable for controlling ducts, tanks, freezers, coolers, display cases. and defrost termination.
More informationARGO (Technical Support) 2201 Dwyer Avenue Utica, NY (Corporate Sales) 85 Middle Road Dunkirk, NY ARH-1 ARH-2 ARH-3
ARGO (Technical Support) 2201 Dwyer Avenue Utica, NY 13501 (Corporate Sales) 85 Middle Road Dunkirk, NY 14048 www.argoindustries.com ARH-1 ARH-2 ARH-3 An ISO 9001-2000 Certified Company P/N 240005131,
More information7800 SERIES EC7895A,C; RM7895A,B,C,D and RM7896A,B,C,D Relay Modules
7800 SERIES EC7895A,C; RM7895A,B,C,D and RM7896A,B,C,D Relay Modules SPECIFICATION DATA FEATURES APPLICATION The Honeywell EC7895/RM7895/RM7896 is a microprocessor based integrated burner control for automatically
More informationElectronic Thermostat
Set FAN Auto On Room SYSTEM Cool Off Heat M18535 Electronic Thermostat OWNER S GUIDE Em Ht Aux Ht Set Room FAN Auto On SYSTEM Cool Off Heat Em.Ht. M18539 1 69-1490 69-1490 Congratulations on the purchase
More information7800 SERIES RM7840E,G,L,M Relay Module
7800 SERIES RM7840E,G,L,M Relay Module APPLICATION SPECIFICATION DATA The Honeywell RM7840 is a microprocessor based integrated burner control for automatically fired gas, oil or combination fuel single
More informationT8034C Heating/Cooling Thermostats
T8034C Heating/Cooling Thermostats INSTALLATI INSTUCTIS APPLICATI These T8034C Thermostats control 4 to 30 Vac singlestage heating-cooling systems. An spdt mercury switch makes (H) to on temperature fall
More informationT8600D Chronotherm IV Deluxe Programmable Thermostats
T8600D Chronotherm IV Deluxe mable Thermostats APPLICATION INSTALLATION INSTRUCTIONS The T8600 Chronotherm IV Deluxe mable Thermostat provides electronic control of 24 Vac singlestage heating and cooling
More information7800 SERIES EC7823/RM7823 Relay Module
7800 SERIES EC7823/RM7823 Relay Module FEATURES SPECIFICATION DATA APPLICATION The Honeywell EC7823/RM7823 is a microprocessor based Flame Detector Relay that can be fitted with any 7800 SERIES amplifier
More informationProduct Number L4006A1017 L4006A1132 L4006A1967 L4006A2007 L4006B1007 L4006B1155 L4006B1163 3/4 (19) L4006H1004
L4006; L6006 Aquastat Controller Aquastat Controllers are immersion type devices for limiting or regulating the temperature of liquids in boilers, storage tanks, and other applications where temperature
More informationC7232A,B Sensor and Controller
C7232A,B Sensor and Controller CARBON DIOXIDE SENSOR FEATURES PRODUCT DATA C7232A C7232B Used for CO 2 based ventilation control. Models available with LCD that provides sensor readings and status information.
More informationT7200D,E Series 2000 Commercial Microelectronic Thermostats
T7200D,E Series 2000 Commercial Microelectronic Thermostats INSTALLATION INSTRUCTIONS APPLICATION The T7200D,E Thermostats provide electronic control of 24 Vac commercial single-zone heating, ventilating
More informationC7031D,G,J C7041B,C,D,F,J,K,P,R Series 2000 Electronic Temperature Sensors
C703D,G,J C70B,C,D,F,J,K,P,R Series 2000 Electronic Temperature Sensors PRODUCT DATA C703D, C70D C70B,C C70R C703G, C70F C70P FEATURES C703D, C70D for immersion mounting sense water temperature. C703G,
More informationSolid Core and Split Core 4-20 ma Output Current Sensors CTS-20; CTP-20
Solid Core and Split Core 4-20 ma Output Current Sensors CTS-20; CTP-20 PRODUCT DATA FEATURES Solid or split core loop-powered current transmitters Fast response time Integral DIN rail mounting flange
More information7800 SERIES EC7885A/RM7885A Relay Module
7800 SERIES EC7885A/RM7885A Relay Module SPECIFICATION DATA 1. Torch-ignited main burner using the S445A Start-Stop Station, or any conventional knee or foot operated start-stop station. 2. Torch-ignited
More informationInstruction manual. WMCR-2, WMCR-3, WMCR-4 and WMCR-6 Circulator Zone Controllers WMCR-1E and WMCR-4E Expansion Modules
Instruction manual WMCR-2, WMCR-3, WMCR-4 and WMCR-6 Circulator Zone Controllers WMCR-1E and WMCR-4E Expansion Modules This manual must only be used by a qualified heating installer/service technician.
More informationT8624D Chronotherm IV Deluxe Programmable Multistage Thermostats
T8624D Chronotherm IV Deluxe mable Multistage Thermostats INSTALLATION INSTRUCTIONS APPLICATION The T8624D Chronotherm IV Deluxe mable Multistage Thermostats provides electronic control of 24 Vac single-zone
More informationT8611M Deluxe Programmable Heat Pump Thermostats
T8611M Deluxe mable Heat Pump Thermostats INSTALLATION INSTRUCTIONS APPLICATION The T8611M Deluxe mable Heat Pump Thermostat provides electronic control of 24 Vac single-zone two compressor or two speed
More informationACNF Series Ceiling-Mount Air Handlers 1½ to 2½ Tons
ANF Series eiling-mount Air Handlers 1½ to 2½ Tons Standard Features Suitable for use with refrigerants R-410A and R-22 heck flowrater for heat pump and cooling-only applications All-Aluminum tube/aluminum
More informationSolid Core and Split Core 0-5, 0-10 Vdc Output Current Sensors CTS-05,10; CTP-05,-10
Solid Core and Split Core 0-5, 0-10 Vdc Output Current Sensors CTS-05,10; CTP-05,-10 DESCRIPTION FEATURES PRODUCT DATA Solid and Split Core Vdc Output Current Transmitters. Fast Response Time. Integral
More informationSolid Core and Split Core Fixed Current Status Switches CSS-O,C; CSP-O,C -F (FIXED) SERIES
Solid Core and Split Core Fixed Current Status Switches CSS-O,C; CSP-O,C -F (FIXED) SERIES PRODUCT DATA FEATURES Solid and Split Core, Fixed Current go/no go switches. Very low operating trip points. LED
More informationSLATE. Rectification Ampli-Check Flame Amplifier INSTALLATION INSTRUCTIONS R8001V1031
SLATE Rectification Ampli-Check Flame Amplifier R8001V1031 INSTALLATION INSTRUCTIONS Scan for more information Application SLATE brings configurable safety and programmable logic together into one single
More informationSLATE. Sub-Base Module INSTALLATION INSTRUCTIONS R8001S9001
SLATE Sub-Base Module R8001S9001 INSTALLATION INSTRUCTIONS Scan for more information Application SLATE brings configurable safety and programmable logic together into one single platform. The platform
More informationSLATE. UV Ampli-Check Flame Amplifier INSTALLATION INSTRUCTIONS R8001S1071
SLATE UV Ampli-Check Flame Amplifier R8001S1071 INSTALLATION INSTRUCTIONS Scan for more information Application SLATE brings configurable safety and programmable logic together into one single platform.
More informationY8150 Fresh Air Ventilation System, W8150 Fresh Air Ventilation Control
Y850 Fresh Air Ventilation System, 850 Fresh Air Ventilation ontrol FEATUES PODUT DATA APPLIATION The Y850 Fresh Air Ventilation System, 850 Fresh Air Ventilation ontrol provide fresh air to a home. The
More information38TKB Air Conditioning Unit Installation and Start-Up Instructions
38TKB Air onditioning Unit Installation and Start-Up Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY ONSIDERATION Improper installation, adjustment, alteration,
More informationInstructions For A and Flame Simulators
Instructions For 123514A and 203659 Flame Simulators Application Flame simulators are devices that simulate a flame by reproducing ultraviolet resistance or rectification characteristics of an actual flame.
More informationGME8. Two-Stage Convertible, Multi-Speed ECM Gas Furnace 80% AFUE. Heating Input: 60, ,000 BTU/h
Two-Stage onvertible, Multi-Speed EM Gas Furnace 80% AFUE Heating Input: 60,000 100,000 BTU/h ontents Nomenclature... 2 Product Specifications... 3 Dimensions... 4 Airflow Data... 5 Wiring Diagrams...
More information7800 SERIES RM7888A Relay Module
7800 SERIES RM7888A Relay Module SPECIFICATION DATA FEATURES APPLICATION The Honeywell RM7888A Relay Module is a microprocessor-based integrated burner control for industrial process semi-automatically
More informationT7300F Series 2000 Commercial Microelectronic Conventional or Heat Pump Thermostat
T7300F Series 2000 Commercial Microelectronic Conventional or Heat Pump Thermostat INSTALLATION INSTRUCTIONS APPLICATION The T7300F Thermostat provides electronic control of 24 Vac commercial single zone
More informationMust be installed by a trained, experienced technician
Installation Guide VisionPRO TH8000 Series Touch-screen Programmable Thermostat This manual covers the following models TH8321097: For up to 3 Heat/2 Cool heat pump or up to 2 Heat/2 Cool conventional
More informationY8150 Fresh Air Ventilation System, W8150 Fresh Air Ventilation Control
Y850 Fresh Air Ventilation System, 850 Fresh Air Ventilation ontrol FEATUES PODUT DATA Designed to help meet local ventilation codes and standards, including ASHAE 62.2-200 standard, Ventilation and Acceptable
More informationCR7075 Two-Stage Lighting Controller
CR707 Two-Stage Lighting Controller FEATURES PRODUCT DATA Light intensity threshold levels field-adjustable by user. Independent Time of Day (TOD) override inputs. Optimum start/stop of lighting loads.
More informationRemote Booster Power Supplies
Remote Booster Power Supplies XLS-BPS6, XLS-BPS60, XLS-BPS6C, XLS-BPS0, XLS-BPS00, XLS-BPS0C FEATURES SPECIFICATION DATA Extends power available to Notification Appliance Circuits (NACs). Available in
More informationComfortNet -Compatible
GMV8 omfortnet -ompatible Two-Stage, Variable-Speed Gas Furnace 80% AFUE Heating Input: 60,000 00,000 BTU/h Standard Features Aluminized steel, dual-diameter tubular heat exchanger Two-stage gas valve
More informationSLATE. Base Module INSTALLATION INSTRUCTIONS R8001A1001
SLATE Base Module R8001A1001 INSTALLATION INSTRUCTIONS Scan for more information Application SLATE brings configurable safety and programmable logic together into one single platform. The platform can
More information7800 SERIES RM7840E,G,L,M; EC7840L Relay Module
7800 SERIES RM7840E,G,L,M; EC7840L Relay Module SPECIFICATION DATA Valve Proving features including: VPS test time When (Never, Before, After, Split or Both) FEATURES APPLICATION The Honeywell RM7840 is
More informationQ382A,B Pilot Burners
Q382A,B Pilot Burners INSTALLATION INSTRUCTIONS APPLICATION The Q382A,B Pilot Burners provide main burner ignition for natural and LP gas-fired equipment. The design makes them ideal for use with any millivolt
More informationSingle and Multi-Function Aquastat Controllers
L4006; L6006 Aquastat Controller Aquastat Controllers are iersion type devices for limiting or regulating the of liquids in boilers, storage tanks, and other applications where control is required. Totally
More information6 Zone 120/60/1vac 3A 24 VAC class 2 2 x 40 VA 2 x 5 amp fuses 1/6 hp, 120 VAC
Viega Zone Control Applications The Viega Zone Control is a wiring and switching center for individual and / or multi- room control. The Zone Control simplifies wiring between Thermostats and Powerheads.
More informationT8611G Chronotherm Deluxe Zoning Heat Pump Thermostat
T8611G Chronotherm Deluxe Zoning Heat Pump Thermostat INSTALLATION INSTRUCTIONS APPLICATION The T8611G Chronotherm Deluxe Zoning Heat Pump Thermostat provides electronic control of 24 Vac zoned heat pump
More informationHE420A Steam Power Humidifier
READ AND SAVE THESE INSTRUCTIONS HE420A Steam Power Humidifier OWNER S GUIDE 69-1112-2 HE420A STEAM POWER HUMIDIFIER WELCOME... to the comfortable world of humidified air. With your Honeywell humidifier
More informationQ7300H Series 2000 Commercial Thermostat Subbases
Q700H Series 000 Commercial hermostat Subbases INSALLAION INSRUCIONS APPLICAION he Q700H hermostat Subbases are used with 700F hermostats to provide electronic control of commercial Vac single or multistage
More informationCT500 Electronic Thermostat
CT500 Electronic Thermostat OWNER'S GUIDE MERCURY NOTICE If this control is replacing a control that contains mercury in a sealed tube, do not place your old control in the trash. Dispose of it properly.
More informationEL7611A/EL7612A Ultrasonic Occupancy Sensors and EL7621A Power Pack PRODUCT DATA
EL7611A/EL7612A Ultrasonic Occupancy Sensors and PRODUCT DATA Proven 30% to 60% utility cost savings because lights are on only when needed. Low initial cost allows fast payback. Models available for 1000
More informationT8112C,DElectronic ProgrammableThermostats
Honeywell T8112C,DElectronic ProgrammableThermostats APPLICATION The T8112C,D thermostats provide electronic programmable control for 24 to 30 Vac heating and cooling systems. @ RECYCLING NOTICE if this
More information7800 SERIES: EC7895A,C; RM7895A,B,C,D; RM7896A,B,C,D RM7897A,C and RM7898A Relay Modules
7800 SERIES: EC7895A,C; RM7895A,B,C,D; RM7896A,B,C,D RM7897A,C and RM7898A Relay Modules SPECIFICATION DATA The RM7897A1002 offers selectable pilot operation, intermittent on terminal 8 or interrupted
More informationARGO AR SERIES CONTROLS
ARGO AR SERIES CONROLS AR822-II, AR861-2II, AR861-3II INSALLAION, OPERAION & MAINENANCE MANUAL AR861-2II AR822-II AR861-3II Information and specifications outlined in this manual in effect at the time
More informationT7047C,G,H Remote Space Sensors
7047,G,H Remote Space Sensors INSALLAION INSRUIONS APPLIAION he 7047 Remote Space Sensors are used in Series 70 ontrol Systems to provide modulating space temperature control. SPEIFIAIONS IMPORAN he specifications
More informationR7824, R7847, R7848, R7849, R7851, R7852, R7861, R7886 Amplifiers for 7800 SERIES and R7140 Relay Modules
R7824, R7847, R7848, R7849, R7851, R7852, R7861, R7886 Amplifiers for 7800 SERIES and R7140 Relay Modules PRODUCT DATA indicate the presence of flame when used with 7800 SERIES and R7140 Relay Modules.
More informationT6572A, T6573A,B, T6992A,B, T6993B Digital Fan-Coil Thermostats XE88/XE100 SERIES
T7A, T7A,B, TA,B, TB Digital Fan-Coil Thermostats XE/XE00 SERES FEATURES PRODUCT DATA Attractive modern styling with digital display makes the thermostat ideal for offices or hotels. Hotel card key input
More informationINSTALLATION INSTRUCTIONS Low Ambient Kit NASA201LA, NASA401LA
INSTALLATION INSTRUTIONS Low Ambient Kit NASA201LA, NASA401LA These instructions must be read and understood completely before attempting installation. DANGER, WARNING, AUTION, and NOTE The signal words
More informationT7100D Microelectronic Conventional Thermostat
T7100D Microelectronic Conventional Thermostat INSTALLATION INSTRUCTIONS APPLICATION A. ENGAGE TABS AT TOP OF THERMOSTAT AND SUBBASE. The T7100D Microelectronic Thermostat provides electronic control of
More informationRA890G Protectorelay Primary Control
Protectorelay Primary Control The RA890G Protectorelay control provides solid state electronic safeguard protection for industrial and commercial gas, oil, or combination gas-oil burners. Designed for
More informationLOW VOLTAGE CONTROL CIRCUIT WIRING
INSTALLATION INSTRUTIONS LOW VOLTAGE ONTROL IRUIT WIRING W**A W**AD WA*S* MODELS W**L WL*S* Bard Manufacturing ompany, Inc. Bryan, Ohio 506 Since 9...Moving ahead just as planned. Manual : 00-58 Supersedes:
More informationR8888A,B Hydronic Circulator Zone Panels with Priority Control
A,B Hydronic Circulator Zone Panels with Priority Control EAURES PRODUC DAA APPLICAION he A,B Hydronic Circulator Zone Panels with Priority Control provide relay switching for multizone hot water control
More informationW7100G Discharge Water Temperature Control
W700G Discharge Water Temperature ontrol FETURES PRODUT DT PPLITION Up to six stages of cooling provided. Expandable system up to 0 cooling stages using a W70. dvanced proportional plus integral microprocessor
More informationREAD AND SAVE THESE INSTALLATION INSTRUCTIONS
Nomenclature: D F I 0 0 H : Open coil element T: Tubular element F: Finned tubular element I: Slip in type F: Flange type 0: No screen left of the heater 1: Screen left of the heater 0: No screen right
More informationInstallation Instructions
KSALA0201R22 KSALA0301410 Low--Ambient Pressure Switch Installation Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY ONSIDERATIONS Improper installation, adjustment,
More informationC6097A,B Pressure Switches
C6097A,B Pressure Switches FEATURES PRODUCT DATA APPLICATION The C6097 Pressure Switches are safety devices used in positive-pressure or differential-pressure systems to sense gas or air pressure changes.
More informationWiring Diagrams. 9AB4-12 Air-Cooled Remote Condenser INDEX OPERATING SEQUENCE ACCESSORIES LEGEND AND NOTES FOR FIG. 1-6
9AB4-12 Air-ooled Remote ondenser Wiring Diagrams INDEX UNIT 9AB DRAWING TYPE DRAWING NUMBER FIG. NO. 4,6 Label Diagram 9AB6-10816 1 8,12 Label Diagram 9AB12-10816 2 AESSORIES OMPONENT PART NO. FIG. NO.
More informationH1008A,D Automatic Humidity Controls
H00A,D Automatic Humidity Controls FEATURES PRODUCT DATA The H00A,D provides automatic control for by-pass flow-through, powered flow-through, steam and drum humidifiers in central heating systems. The
More informationInstallation Instructions HEAT COOL FAN POWER
DIGITAL THERMOSTAT Installation Instructions P/N P474-2300RE MULTI-STAGE & PUMP WIRELESS REEIVER Use with most Air onditioning & Heating Systems including: 1 or 2 Stage Electric ooling & Gas Heating, Heat
More information232xt Wiring Diagrams and Specifications SPECIFICATIONS: REV 1.01
232xt Wiring Diagrams and Specifications Voltage Selection Settings 1 2 3 Wire Xtreme Pad color to color to the wires on Programmer (Red to Red, ect.) ( / Yellow ) Position 12-24VA 15-24VD P5* Position
More information