REGULATORY ENVIRONMENT ON ELECTRICAL AND ELECTRONIC PRODUCTS IN ASEAN. Table of Contents

Size: px
Start display at page:

Download "REGULATORY ENVIRONMENT ON ELECTRICAL AND ELECTRONIC PRODUCTS IN ASEAN. Table of Contents"

Transcription

1 REGULATORY ENVIRONMENT ON ELECTRICAL AND ELECTRONIC PRODUCTS IN ASEAN Table of Contents I. Rationale for Regulation II. III. IV. Regulatory Authority Legislative Framework Mandatory V. Mode of Regulation and Types of Conformity Assessment Regimes VI. VII. VIII. Flowchart of each Member Country's Regime Voltage, Frequency and Mains Plug Configuration Contact Person 1

2 I. RATIONALE FOR REGULATION COUNTRY Brunei Darussalam Cambodia Indonesia Lao PDR Malaysia Myanmar Philippines Singapore Thailand Viet Nam RATIONALE FOR REGULATION Ensure safety and reliability in the supply of electricity Consumer Protection Consumer Protection Consumer's Rights and Benefits Protection. Promote and Facilitate the Producers of Goods and s Ensure safety and Consumer protection. Ensure Safety and Consumer protection. Upgrade the quality of products. Protect and safeguard the interest of consumers especially in matters of health and safety. Consumer Protection. Consumer Protection. Ensure Safety in the use of electrical products. 2

3 II. REGULATION BODY COUNTRY REGULATORY BODY Brunei Darussalam Ministry of Development Department of Electrical Services Cambodia Ministry of Commerce (Cambodia Import Export Inspection and Fraud Repression Department Camcontrol) Indonesia Lao PDR Ministry of Industry Mines and Energy (Department of Industrial of Cambodia ISC) Ministry of Industry and Trade. Ministry of Energy and Mineral Resources. Science, Technology and Environment Agency Department of Intellectual Property, Standardization and Metrology Malaysia Energy Commission (Suruhanjaya Tenaga) Myanmar Ministry of Industry (1) Directorate of Industrial Supervision and Inspection Electrical Inspection Department Philippines Bureau of (BPS) under the Department of Trade and Industry (DTI). Singapore Thailand Viet Nam, ivity and Innovation Board (or SPRING Singapore in short) Thai Industrial Institute (TISI) under the Ministry of Industry. Directorate for and Quality (STAMEQ) under Ministry of Science and Technology (MOST) 3

4 III. LEGISLATIVE FRAMEWORK COUNTRY LEGISLATIVE FRAMEWORK Brunei Darussalam Electricity Act (1984) Cambodia Law on the management of quality and safety of product and services (2000) Indonesia Act No. 8 / 1999 Subdecree No.42 on Industrial of Cambodia (2001) Lao PDR Decree of the Prime Minister regarding the Management on and Quality of s and the Metrology Management Quality Inspection of Import Goods Malaysia Electricity Supply Act 1990; and Electricity Regulations 1994 Myanmar Electricity Law (1984) Philippines Republic Act 4109 Singapore Consumer Protection (Safety Requirements) Regulations 2002* which is based on the Consumer Protection (Trade Descriptions and Safety Requirements) Act (Chapter 53) * Consumer Protection (Safety Requirements) Regulations 1991 has been revoked and replaced by Regulations

5 COUNTRY LEGISLATIVE FRAMEWORK Thailand Industrial Act. (1968) Viet Nam Act on Quality issued by the National Assembly Decision on the Ministry of Science and Technology on Safety Certification. Decision of the Ministry of Science and Technology on State Inspection of ImportExport s Quality. IV. MANDATORY Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Brunei Darussalam No Mandatory standards Country Cambodia 01 Fuses/Fuse Links up to 63 A type or grouping Domestic Please tick box if Relevant International Extent of Alignment CS 0030:2003 IEC ,Ed.3:1998 State reason if MOD 5

6 02 Electrical Hair Dryers 03 Electrical Coffee/Tea Makers 04 Electrical Deep Fryers 05 Electrical Food Steamers 06 Electrical Slow Cookers CS 0010:2003 CS 0011:2003 CS 0010:2003 CS 0012:2003 CS 0010:2003 CS 0013:2003 CS 0010:2003 CS 0012:2003 CS 0010:2003 CS 0012: Electrical Iron CS 0010: Electrical Blenders 09 Electric Food Processors CS 0014:2003 CS 0010:2003 CS 0015:2003 CS 0010:2003 CS 0015:2003 IEC , ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC

7 10 Electric Juice Extractors 11 Electric Grinders 12 Electric Mixers CS 0010: Electric Microwave Ovens 14 Electric ventilating fan & regulators CS 0010:2003 IEC CS 0015:2003 ed.3:1991+am.1&2:19 94+Am.2;1999 IEC CS 0010:2003 IEC ed.3:1991+am.1&2:19 CS 0015: Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 CS 0015: Am.2;1999 IEC CS 0010:2003 IEC ed.3:1991+am.1&2:19 CS 0016: Am.2;1999 IEC CS 0017:2003 IEC Television CS 0029:2003 IEC Carpet CS 0010:2003 Cleaners 17 Vacuum Cleaners and accessories 18 Electric Washing Machines CS 0018:2003 CS 0010:2003 CS 0018:2003 CS 0010:2003 CS 0019:2003 CS 0020:2003 IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC

8 19 Electric Freezers 20 Electric Rice Cookers 21 Electric Sewing Machine 22 Electric Soldering Irons 23 Electric Grinders ( up to 100 mm ) CS 0010:2003 CS 0011:2003 CS 0010:2003 CS 0012:2003 CS 0010:2003 CS 0022:2003 CS 0010:2003 CS 0023:2003 CS 0042:2003 CS 0048: Refrigerators CS 0021:2003 CS 0021: pin 13amp CS 0049:2003 socketoutlet CS 0051: Incandescent lamp IEC , ed.3:1991+am.1&2:19 94+Am.2;1999 IEC ,Ed.4: Am.2:1999 IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC , ed.3:1991+am.1&2:19 94+Am.2;1999 IEC ,Ed.3:1994 IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC :1996 IEC ,Ed.1 :1989 IEC ,Ed Am.1:1995 IEC :1992 IEC :2000 IEC :1997 IEC CS 0006:2003 IEC 60064:1993 IEC :1999 NEQ 8

9 27 PVC insulated copper cable 28 3pin rectangular type 13 amp.plug 29 3pin round type 15 mp.plug 30 Multiway adaptors 31 General purpose switches CS 0024:2003 CS 0025:2003 CS 0017:2003 CS 0051:2003 IEC :1993,Am.1(1995),A m.2(1998) IEC :1997 IEC :1997 IEC CS 0017:2003 IEC :1997 CS 0017:2003 IEC :1997 CS 0026:2003 IEC Cassette player CS 0029:2003 IEC Portable radio cassette player/recorder CS 0029:2003 IEC Video compact disc player 35 Home computer system(inclusi ve of monitor, printer, speaker, other operated accessories and mains CS 0029:2003 IEC CS 0047:2003 IEC 60950:1991 9

10 36 PVC insulated and sheated cable with 300/500 V rated voltage 37 PVC insulated wire with rated voltage 450/750 V 38 Self ballast lamp for general lighting service 39 Lowvoltage distribution link fuses 40 Lampholder for tubular fluorescent lamps 41 Staterhaolder for tubular fluorescent lamps 42 Miniature Circuit Breaker 43 Electrical Standing Lamps 44 Electrical Table Lamps CS 0050:2003 IEC 502:1994 CS 0050:2003 IEC 502:1983 CS 0027:2003 IEC 60968:1988 CS 0030:2003 IEC :1998 CS 0031:2003 IEC CS 0031:2003 IEC CS 0032:2003 IEC CS 0034:2003 CS 0035:2003 CS 0034:2003 CS 0035:2003 IEC IEC IEC IEC

11 45 Electrical Hand Lamps 46 Electrical MultiPurpose Cookers 47 Electrical Hair Clippers 48 Electrical Shavers 49 Electrical Fixed Immersion Heaters 50 Portable Immersion Heaters 51 Electrical Portable Ovens CS 0034:2003 CS 0036:2003 CS 0010:2003 CS 0037:2003 CS 0013:2003 CS 0012:2003 CS 0010:2003 CS 0033:2003 CS 0010:2003 CS 0033:2003 CS 0010:2003 CS 0038:2003 CS 0010:2003 CS 0039:2003 CS 0010:2003 CS 0037:2003 IEC ,Ed.4:1996 IEC ,Ed.2:1996 IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC IEC IEC , ed.3:1991+am.1&2:19 94+Am.2;1999 IEC ,Ed.4: IEC ,Ed.3 + Am.1:1994 +Am.2:1999 IEC ,Ed.4: IEC , ed.3:1991+am.1&2:19 94+Am.2;1999 IEC ,Ed.1:1994 IEC , ed.3:1991+am.1&2:19 94+Am.2;1999 IEC ,Ed.1:1994 IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC

12 52 Electrical Grillers 53 Electrical Roasters 54 Electrical ceiling fan and regulator 55 Electrical movinglouvre fan and regulator 56 Electric Table Fan and regulators 57 Electrical wall fan and regulators 58 Lighting Chains CS 0010:2003 CS 0037:2003 CS 001:2003 CS 0037:2003 CS 0045:2003 CS 0040:2003 CS 0045:2003 CS 0040:2003 CS 0045:2003 CS 0040:2003 CS 0045:2003 CS 0040:2003 CS 0034:2003 CS 0041: Electric Circular Saws CS 0042:2003 and Circular CS 0028:2003 Knives 60 Electric Drill CS 0042:2003 CS 0043:2003 IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC ed.3:1991+am.1&2:19 94+Am.2;1999 IEC IEC IEC IEC IEC IEC IEC IEC IEC IEC ,Ed.5:19999 IEC ,Ed.2: Am.1: IEC ,Ed.1: Am.1:1992 IEC ,Ed.2:1993 IEC ,Ed.1:1989 IEC

13 61 Adapter CS 0044:2003 CS 0046:2003 CS 0029:2003 CS 0047:2003 IEC 60742: Am.1+ Am2.:1992 IEC :1996 IEC 60065:19998 IEC 60950: Fluorescent Lamp: Safety requirements CS 0008:2003 IEC 60081:1997 NEQ Country Indonesia Incandescent lamps type or grouping Domestic Please tick box if Relevant SNI V JIS C 421 International Extent of Alignment State reason if MOD Alternating current ballast for fluorescent lamp Drycells batteries Compound for insulation of electric wire and cable with 1 kv up to 30 kv rated voltage SNI V JIS C 108 SNI V IEC 86, JIS C 8501, ANSI 181 SNI V IEC

14 Country type or grouping Domestic Please tick box if PVC insulated and sheated cable with 300/500 V rated voltage Relevant SNI V IEC International Extent of Alignment State reason if MOD Insulated and PVC covered power cable for ground identification volatage 0,6/1 kv(nyy/nayy) Indonesia PVC insulated and sheated, steel or aluminium wire shielded ground cables rated voltage 0,6/1 kv(nyf Gb Y/ NAYFGbY/NXY RGbY/NARGbY/ NYRY/NAYRY) Indonesia PVC insulated and sheated underground cable, steel or aluminium band shielded with 0,6/1 kv rated voltage SNI V IEC SNI V IEC 5021 SNI V 14

15 Country Indonesia PVC insulated and sheated flexible cable with 500 V rated voltage (NYMHY) type or grouping Domestic Please tick box if SNI V Relevant International Extent of Alignment State reason if MOD Indonesia PVC insulated and sheated flexible cable with 500 V rated voltage (NYMHY oval) Indonesia PVC insulated and sheated flexible cable with 1000V rated voltage Indonesia PVC insulated and sheated flexible double wire and triple wire cable with rated voltage up to 380 V Indonesia PVC insulated and sheated double wire up to five wire cable with rated voltage up to 380 V SNI V SNI V SNI V SNI V 15

16 Country Indonesia PVC insulated wire rated voltage with 450/750 V type or grouping Domestic Please tick box if Relevant SNI V IEC International Extent of Alignment State reason if MOD Indonesia Selfballast lamp for general lighting service SNI V IEC Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Lao PDR No standards 16

17 Country Malaysia 1 PLUG TOP (PLUGS) type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Two pole plugs & supply cords 13A Fused plugs 15A Fused plugs Adaptors (multiway) MS 1578:2003 BS EN MS 589:PT.1:1997 BS 1363: PT.1 MS 1577:2003 BS 546 MS 589: PT.3:1997 BS 1363:PT.3 Cable Connectors No Corresponding MS IEC IEC IEC IEC IEC IEC Appliance Connectors 2 SWITCHES AND DIMMERS MS IEC :1996 IEC General purpose switches MS 616:PT.1:1998 IEC MOD Testing ambient temperature = 25 C ± 5 C (IEC amb temp = 20 C ± 5 C) 17

18 Country type or grouping Domestic Please tick box if Electronic switches Malaysia Remotecontrol switches Relevant International Extent of Alignment MS 616:PT.2:Sect.1:2000 IEC MOD MS 616:PT.2:Sect.2:2000 IEC MOD Malaysia Time Delay Switches MS 616:PT.2:Sect.3:2000 IEC MOD 3 SOCKET OUTLES 15A AND BELOW (with or without elcb/rcd) State reason if MOD Testing ambient temperature = 25 C ± 5 C (IEC amb temp = 20 C ± 5 C) Testing ambient temperature = 25 C ± 5 C (IEC amb temp = 20 C ± 5 C) Testing ambient temperature = 25 C ± 5 C (IEC amb temp = 20 C ± 5 C) Electric Shaver Socket Outlets Isolating Transformer MS EN 60742:1998 EN IEC MS EN 60742:1998 EN IEC NEQ NEQ 13A Portable Switched Socket Outlets 13A Unswitched Socket Outlets 15A Socket Outlets MS 589:PT.2:1997 BS 1363:PT.2 MS 589:PT.2:1997 BS 1363:PT.2 MS 1577:2003 BS 546 ACDC or ACAC Converter (Adaptor) MS EN 60742:1998 EN IEC IEC (IT Equip.) NEQ NEQ 18

19 Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Portable 2Pin Socket Outlets MS 1579:2003 SS 448:2001 Cooker Control Units 4 LAMPHOLDERS Lampholders for tubular fluorescent lamps Staterholders for tubular fluorescent lamps No Corresponding MS BS 4177 : 1992 MS IEC 60400:1999 IEC MS IEC 60400:1999 IEC CEILING ROSES 6 BAYONET CAPS AND MULTIWAYS ADAPTORS MS 770:1982 Bayonet Lampholders MS 769:1982 Malaysia Bayonet Adaptors MS 769: FLUORESCENT LAMPS FITTING EXCLUDING TUBES IF IMPORTED SEPARATELY Fixed general purpose luminaires MS IEC :1997 IEC MS IEC :1997 IEC

20 Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Recessed luminaires MS IEC :1997 IEC MS IEC :1998 IEC Lampholders / Starterholders MS IEC 60400:1999 IEC Glowstarters for tubular fluorescent MS IEC 60155: 1996 IEC CAPACITORS FOR FLUORESCENT LAMPS Capacitors for use in tubular fluorescent lamp circuit MS IEC 61048:1999 MS IEC 61049:1999 IEC IEC BALLAST FOR FLUORESCENT Malaysia Ballast for tubular fluorescent lamps MS 141 :PT.1:1992 & MS 141 :PT.2:1992 IEC IEC MOD MOD Additional ballast lost requirement Electronic Ballast MS IEC 60928:1995 MS IEC 60929:1995 IEC IEC

21 Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD 10 CIRCUIT BREAKER INCLUDING AC CURRENT OPERATED LEAKAGE CIRCUIT BREAKERS AND MINIATURE CIRCUIT BREAKERS Residual Current Circuit Breakers MS IEC :2003 IEC 10081, Ed.2 Miniature Circuit Breaker (MCB) MS IEC 60898:1998 IEC RCBO s No Corresponding MS IEC IEC IEC Fuse Base & Carrier up to 32A Fuses/Fuse Links up to 63A No Corresponding MS IEC , Ed.3 IEC , No Corresponding MS IEC IEC , IEC WATER HEATER INCLUDING HEATING ELEMENTS IF IMPORTED SEPARATELY Electric Stationary Instantaneous Water Heaters MS 472 :PT.3 :SEC.3.1 :1986 BS 3456:PT.3, SEC. 3.9 IEC IEC NEQ NEQ Electric Storage Water Heaters MS IEC :1995 MS IEC :2000 IEC IEC

22 Country type or grouping Domestic Please tick box if 12 HAND OPERATED HAIR DRYERS Relevant International Extent of Alignment State reason if MOD Malaysia Electric Hair Dryers MS IEC 3351:1995 IEC MS IEC :1999 IEC Electric Hair Styling Sets MS IEC 3351:1995 IEC MS IEC :1999 IEC DOMESTIC LIGHT FITTINGS HAVING ACCESSIBLE METAL PARTS Electric Standing Lamps MS IEC :1997 IEC MS IEC :1997 IEC Electric Table Lamps MS IEC :1997 IEC MS IEC :1997 IEC Electric Hand Lamps IEC , Ed.4:1996 IEC , Ed.2:1996 IEC , Ed.4 IEC , Ed.2 22

23 Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment 14 ELECTRIC KETTLE INCLUDING HEATING ELEMENTS IF IMPORTED SEPARATELY State reason if MOD Malaysia Electric Coffee MS IEC :1995 IEC / Tea Makers MS IEC :1999 IEC Electric Deep Fryers MS IEC 3351:1995 IEC MS IEC :1995 IEC Electric Egg Boilers MS IEC 3351:1995 IEC MS IEC :1999 IEC Electric Jugs MS IEC 3351:1995 IEC MS IEC :1999 IEC

24 Country Malaysia Electric Food Steamers type or grouping Domestic Please tick box if MS IEC :1995 Relevant International Extent of Alignment State reason if MOD IEC MS IEC :1999 IEC Electric Warming Plates No Corresponding MS IEC IEC , Ed. 4 Electric Slow Cookers MS IEC :1995 IEC MS IEC :1999 IEC Electric Steam Boats MS IEC :1995 IEC MS IEC :1999 IEC Electric Built in Hobs MS IEC :1995 IEC MS IEC :1995 IEC Malaysia Electric Kettles MS IEC 3351:1995 IEC MS IEC :1999 IEC

25 Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Electric Airpots MS IEC :1995 IEC MS IEC :1999 IEC Electric Steam Generator Appliances MS IEC :1995 IEC MS IEC :1999 IEC Electric Aroma Vaporisers No corresponding MS IEC IEC Electric MS IEC :1995 Heating Elements for Kettles MS IEC : ELECTRIC SMOOTHING IRONS Electric Irons MS IEC :1995 MS IEC : ELECTRIC SHAVERS IEC IEC IEC IEC Malaysia Electric Hair Clippers MS IEC :1995 MS IEC :2002 IEC , Ed.3 IEC , Ed 4: Electric Shavers MS IEC :1995 MS IEC :2002 IEC , Ed.3 IEC 33528, Ed 4 25

26 Country type or grouping Domestic Please tick box if 17 FOOD MIXERS/BLENDERS Relevant International Extent of Alignment State reason if MOD Electric Blenders MS IEC :1995 MS IEC :1996 IEC IEC Electric Choppers MS IEC :1995 MS IEC :1996 IEC IEC Malaysia Electric Food Processors MS IEC :1995 MS IEC :1996 IEC IEC Electric Juice Extractors MS IEC :1995 MS IEC :1996 IEC IEC Electric Grinders MS IEC :1995 MS IEC :1996 IEC IEC Electric Mixers MS IEC :1995 MS IEC : IMMERSION WATER HEATERS IEC IEC Electric Fixed Immersion Heaters MS IEC :1995 MS IEC :1996 IEC , Ed.3 IEC , Ed.1 Malaysia Portable Immersion Heater MS IEC :1995 MS IEC :1996 IEC , Ed.3 IEC , Ed.1 26

27 Country type or grouping Domestic Please tick box if 19 HIFI SETS Relevant International Extent of Alignment State reason if MOD Subwoofer MS IEC 60065:1997 IEC Amplifier MS IEC 60065:1997 IEC Cassette Player MS IEC 60065:1997 IEC Equalizers/ Mixers MS IEC 60065:1997 IEC HiFi System MS IEC 60065:1997 IEC Karaoke MS IEC 60065:1997 IEC Laser Disc Player MS IEC 60065:1997 IEC PA System MS IEC 60065:1997 IEC Portable HiFi System Portable RadioCassette Player / Recorder MS IEC 60065:1997 IEC MS IEC 60065:1997 IEC Radio MS IEC 60065:1997 IEC Radio Alarm MS IEC 60065:1997 IEC Malaysia Tuner / Receiver Turn tables / Record Players MS IEC 60065:1997 IEC MS IEC 60065:1997 IEC

28 Country type or grouping Domestic Please tick box if Compact Disc Players Relevant International Extent of Alignment State reason if MOD MS IEC 60065:1997 IEC MOSQUITO MATT VAPORISERS 21 TOASTERS/OVENS MS IEC :1995 IEC IEC Electric Bread Makers MS IEC :1995 MS IEC :1995 MS IEC IEC Electric Bread Toasters MS IEC :1995 MS IEC :1995 MS IEC IEC Electric Portable Ovens MS IEC :1995 MS IEC :1995 MS IEC IEC Electric Grillers MS IEC :1995 MS IEC :1995 MS IEC IEC Malaysia Electric Microwave Ovens MS IEC :1995 IEC MS IEC :1995 IEC Electric Sandwich Makers / Waffle Makers MS IEC :1995 MS IEC :1995 MS IEC IEC

29 Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Electric Stationary Electric Ovens MS IEC :1995 IEC MS IEC :1999 IEC Electric Roasters MS IEC :1995 MS IEC FANS Electric movinglouvre fans & regulators Electric ceiling fans & regulators Malaysia Electric ventilating fans & regulators Electric auto fans & regulators MS IEC :1995 MS IEC MS 1219 : 2002 MS 1220 : 2001 MS IEC MS 1219 : 2002 MS 1220 : 2001 MS IEC MS 1219 : 2002 MS IEC MS 1219 : 2002 MS 1220 : 2001 IEC IEC IEC IEC IEC IEC IEC MS IEC IEC IEC IEC IEC MOD MOD MOD MOD MOD MOD MOD MS 1219: New requirement for detachable part, temperature marking, maintenance instruction, moisture resistance, supply connection, external flexible cord and mechanical strength MS 1220: 1) Cl 7.2: statement with at least five running positions is replaced by with at least three running positions 2) Cl : Rating of frequency is defined to suit local conditions 29

30 Country type or grouping Domestic Please tick box if Electric pedestal fans & regulators Electric table fans & regulators Electric wall fans & regulators Electric range hoods MS IEC MS 1219 : 2002 MS 1220 : 2001 MS IEC MS 1219 : 2002 MS 1220 : 2001 MS IEC MS 1219 : 2002 MS 1220 : 2001 Relevant International Extent of Alignment IEC IEC IEC IEC IEC IEC IEC IEC IEC No Corresponding MS IEC , Ed.3 IEC , Ed.2 MOD MOD MOD MOD MOD MOD State reason if MOD MS 1219: New requirement for detachable part, temperature marking, maintenance instruction, moisture resistance, supply connection, external flexible cord and mechanical strength MS 1220: 3) Cl 7.2: statement with at least five running positions is replaced by with at least three running positions 4) Cl : Rating of frequency is defined to suit local conditions Malaysia Electric Air Coolers 23 TELEVISION No Corresponding MS IEC IEC Television MS IEC : 1997 IEC Projection Television MS IEC : 1997 IEC

31 Country type or grouping Domestic Please tick box if 24 VACUUM CLEANERS Relevant International Extent of Alignment State reason if MOD Carpet Cleaners MS IEC : 1995 IEC MS IEC : 1995 IEC Vacuum MS IEC : 1995 Cleaners & Accessories MS IEC : VIDEO PLAYER IEC IEC Video compact disc players Video Cassette Recorder / Players Digital versatile disc players Video Rewinder MS IEC : 1997 IEC MS IEC : 1997 IEC MS IEC : 1997 IEC MS IEC : 1997 IEC

32 Country Malaysia Children Video Games type or grouping Domestic Please tick box if 26 WASHING MACHINES Relevant International Extent of Alignment MS IEC : 1997 IEC State reason if MOD Electric Cloth Dryers No Corresponding MS IEC 3351 IEC , Ed. 2 Electric Washing Machines MS IEC : 1995 MS IEC : 1995 IEC IEC MS IEC : 1995 IEC REFRIGERATORS Malaysia Electric Refrigerators MS IEC : 1995 MS IEC : 2002 IEC , IEC Electric Freezers MS IEC : 1995 MS IEC : 2002 IEC , IEC Malaysia Electric Minibars MS IEC : 1999 MS IEC : 1999 IEC , IEC ELECTRIC RICE COOKER MS IEC : 1995 IEC MS IEC : 1999 IEC

33 Country type or grouping Domestic Please tick box if 29 LIGHTING CHAINS Relevant International Extent of Alignment State reason if MOD Lighting chains MS IEC : 1997 MS IEC : DOMESTIC POWER TOOLS IEC , Ed. IEC , Ed. Electric Circular Saws and circular knives (Cutting Blade up to 160 mm) No Corresponding MS IEC , IEC , Malaysia Electric Drills (Drill bit size up to 10 mm) No Corresponding MS IEC IEC Electric Sewing Machines MS IEC : 1995 MS IEC : 1996 IEC , Ed. 3 IEC , Ed. 3 Electric Soldering Irons MS IEC : 1991 MS IEC : 1996 IEC IEC Electric Grinders (up to 100 mm) No Corresponding MS IEC , IEC Electric spray guns for nonflammable liquids (up to 100 bars) No Corresponding MS IEC , IEC , 33

34 Country Malaysia Electric Jig and Sabre Saws (up to 60 mm) type or grouping Domestic Please tick box if No Corresponding MS Relevant International IEC , IEC , Extent of Alignment State reason if MOD Electric hedge trimmers and Grass shears (up to 750 W) No Corresponding MS IEC , IEC Electric Planers (up to 500 W) No Corresponding MS IEC IEC Portable Battery Chargers (up to 12V) MS IEC :1995 MS IEC :1996 IEC :1995 IEC Electric Routers and trimmers (up to 500 W) No Corresponding MS IEC , IEC , Electric Sanders (up to 300 W) Malaysia Trimmers (up to 300 W) No Corresponding MS IEC IEC , No Corresponding MS IEC IEC

35 Country type or grouping Domestic Please tick box if Relevant International 31 WIRES / CABLES / CORDS (nonarmoured) 0.5 sq mm35 sq. mm Extent of Alignment State reason if MOD Insulated flexible cords and cable MS 140 : 1987 BS 6500 PVCinsulated cable (nonarmoured) for electric power and supply MS 136 : 1995 MS 140: 1987 BS 6004 BS 6004 Polyvinyl chloride Insulated flexible cords Rubber insulated cord and flexible cables MS 140:1987 IEC , IEC , MS 140:1987 BS 6500 IEC IEC , NEQ NEQ NEQ NEQ 35

36 Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Myanmar No Mandatory standards Country Philippines Ballast for tubular fluorescent lamps Safety type or grouping Domestic Please tick box if PNS 121:1996 Amd. 02:1997 Relevant International IEC 920:1990 Amd. 01:1993 Amd. 02:1995 Extent of Alignment State reason if MOD Ballast for tubular fluorescent lamps Performance PNS 122:1996 Amd. 01 & 02:1997 IEC 921:1990 Amd. 01:1990 Amd. 02:1994 Class H Fuses PNS 13:1999 UL 198B:1995 Note: Adopted IEC but subject to implementation. PVC insulated electric copper wires and cables PNS 35:1996 IEC 228:1978 Not equivalent 36

37 Country Philippines Tungsten filament lamps for domestic and similar general lighting purposes Safety type or grouping Domestic Please tick box if Relevant International PNS 381:1995 IEC 4321:1993 And. 01:1995 Extent of Alignment State reason if MOD Tungsten filament lamps for domestic and similar general lighting purposes Performance Lamp holders and starter holders for tubular fluorescent lamps PNS 382:1995 IEC 64:1993 PNS 42:1997 IEC 400:1996 Glowstarters for fluorescent lamps PNS 45:1997 Amd. 01:1997 IEC 155:1993 Amd. 01:1995 Fuseholders specifications Snap switches for general use PVC tapes for electrical insulation PNS 56:1996 ANSI/UL 512:1992 PNS 57:1996 UL 20:1995 PNS 79:1992 IEC 4543 NEQ Note: IEC was already adopted subject to implementation. 37

38 Country Philippines Edison Screw lamp holders type or grouping Domestic Please tick box if Relevant International PNS 80:1997 IEC 238:1996 Extent of Alignment State reason if MOD Ballast for high pressure mercury vapour lamp PNS 105:1986 Knife switches PNS 118:1992 AC supplied electronic ballast for tubular fluorescent lamps Safety PNS 1351:1997 IEC 928: AC supplied electronic ballast for tubular fluorescent lamps Performance PNS 1352:1993 Amd. 01 & 02: 1997 IEC 929:1990 Amd. 01:1994 & 02:1996 Polyvinyl chloride insulated flexible cords Lighting sets using miniature and subminiature lamps for decorative purposes for indoor use PNS 163:1994 IEC 227 NEQ Note: PNS is single sheathed while IEC is double sheathed. PNS 189:

39 Country Philippines Non ducted air conditioners and heat pumps testing and rating for performance type or grouping Domestic Please tick box if PNS 240:1998 Amd. 01:2000 Relevant International ISO 5151:1994 Extent of Alignment State reason if MOD Safety requirements for electric irons PNS 2541:1994 Amd. 01:2000 IEC 33523:1993 Amd. 01:2000 Safety requirements for appliances for heating liquids Household appliances mains operated electronic appliance Safety Safety requirements for toasters, grills, roasters and similar appliances PNS 255:1996 IEC :1995 PNS 256:1999 IEC 65:1998 PNS 272:1996 IEC33529:

40 Country Philippines Nonducted air conditioners Energy Efficiency Ratio (EER) and labelling requirements type or grouping Domestic Please tick box if Relevant International PNS 3961:1998 Extent of Alignment State reason if MOD Refrigerators and freezers Energy Efficiency Factor (EEF) and labelling requirements Moulded case circuit breakers Selfballasted lamps for general lighting services Safety Selfballasted lamps for general lighting services Performance PNS 3962:1997 PNS 519:1991 PNS 6031:1993 IEC 968:1988 PNS 6032:1993 IEC 969:

41 Country Philippines General Requirements for safety of household and similar electrical appliances type or grouping Domestic Please tick box if Relevant International PNS 1079:1994 IEC 3351:1991 Amd. 01:1994 Extent of Alignment State reason if MOD Safety requirements for vacuum cleaners and water suction cleaning appliances Safety requirements for kitchen machines Singlecapped fluorescent lamps Performance PNS 1169:1993 IEC33522:1993 PNS 1244:1994 IEC335214:1984 PNS 1261:1995 IEC 901:1992 Luminaires PNS 1328:1996 IEC 5981:1992 Plugs and socket outlets for households and similar purposes General requirements PNS 14861:1996 IEC 8841:

42 Country Philippines Safety requirements for storage water heaters type or grouping Domestic Please tick box if PNS 1558:1997 Amd. 01,02,03: 1997 Relevant International IEC335221:1989 Amd. 01,02:1990 Amd. 03:1992 Extent of Alignment State reason if MOD Plugs and socket outlets for domestic and similar general use standards Capacitors for use in tubular fluorescent and other discharge lamps circuits Safety Capacitors for use in tubular fluorescent and other discharge lamps circuits Performance Safety requirements for electric ironers Safety requirements for spin extractors Boxes for rigid metal conduits PNS 1572:1997 IEC 83:1975 MOD Put another column for configuration of plugs to meet Philippine condition. PNS 1574:1997 IEC 1048:1991 PNS 1575:1997 IEC 1049:1991 PNS 1679:1998 IEC :1987 PNS 1680:1988 IEC 33524:1993 PNS 1829:1999 JISC 8336:

43 Country Philippines Safety requirements for stationary cooking ranges, hobs, ovens and similar appliances type or grouping Domestic Please tick box if Relevant International PNS IEC :2000 IEC :2000 (IEC Published 1998) Extent of Alignment State reason if MOD Safety requirements for washing machines PNS IEC :2000 IEC :2000 (IEC Published 1998) MOD Class 01appliance is allowed. Safety requirements for refrigerating appliances and ice makers PNS IEC :2000 IEC :2000 (IEC Published 1999) Safety requirements for microwave ovens PNS IEC :2000 IEC :2000 (IEC Published 1998) Safety requirements for range hoods PNS IEC :2000 IEC :2000 (IEC Published 1995) Safety requirements for massage appliances PNS IEC :2000 IEC :2000 (IEC Published 1993) 43

44 Country Philippines Safety requirements for motor compressors type or grouping Domestic Please tick box if PNS IEC :2000 Relevant International IEC :2000 (IEC Published 1998) Extent of Alignment State reason if MOD Safety requirements for instantaneous water heaters PNS IEC :2000 IEC :2000 (IEC Published 1997) Safety requirements for electrical heat pumps airconditioners and dehumidifiers PNS IEC :2000 IEC :2000 (IEC Published 1995) Safety requirements for portable immersion heaters PNS IEC :2000 IEC :2000 (IEC Published 1994) Safety requirements for Fans PNS IEC :2000 IEC :2000 (IEC Published 1997) Double capped fluorescent lamps Performance PNS IEC 60081:2001 IEC 60081:

45 Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment Singapore 41 1Air cooler No corresponding SS IEC :1997 State reason if MOD 2Adaptor No corresponding SS IEC :1983 with Amendments 1&2 (1992) Electrical appliances or IEC : 1999 SS 143 : 1988 with A1 & A2 or SS 143 : 2000 (applicable for electronic appliances) IEC :1985 with A1, 2, & 3 (Electronic appliances) or IEC 60065: 1998 SS 337:1997 (applicable for computer / telephonic appliances) IEC :1991 with A1, 2, 3 & 4 Computer / telephonic appliances or IEC 60950: 1999 MOD Humidity test under tropical conditions 3Any other audio products SS 143 : 1988 with A1 & A2 or SS 143 : 2000 IEC :1985 with Amendment 1 (1987) & Amendment 2 (1989) & Amendment 3 (1992) or IEC 60065:1998 4Cooking range SS 146: Part 2: 7: 1988 with A1 or SS 146:Part 2:7:1999 IEC :1986 or IEC :1997 5Coffee maker, slow cooker, steam boat and similar appliances SS 146 Part 2:2 :1997 IEC :1986 or IEC :

46 Country Singapore 6Decorative lighting fixture type or grouping Domestic Please tick box if SS 263: Part 10: 1990 or SS 263 Part 10 : 2000 Relevant International IEC :1982 with Amendment 1 (1987) & Amendment 2 (1992) or IEC :1998 Extent of Alignment State reason if MOD 7Hairdryer SS 146: Part 2: 9: 1994 with A1 or SS146:Part 2:9:1997 IEC :1986 or IEC :1996 8Home computer system (inclusive of monitor, printer, speaker and other mains operated accessories) 9Highfidelity set SS 337:1997 IEC :1991 with Amendment 1 (1992) & Amendment 2 (1993) & Amendment 3 (1995) and Amendment 4 SS 143: 1998 with A1 & A2 or SS 143 : 2000 IEC :1985 with Amendment 1 (1987) & Amendment 2 (1989) & Amendment 3 (1992) or IEC 60065: Iron SS146:Part 2:1:1996 IEC :1993 MOD Humidity test under tropical conditions 11Immersion water heater SS 146 Part 2: 14 : 1998 IEC : Kettle SS146:Part 2:2:1997 IEC :1986 or IEC : Laser disc set SS 143: 1988 with A1 & A2 or SS 143 : 2000 IEC :1985 with Amendment 1 (1987) & Amendment 2 (1989) & Amendment 3 (1992) or IEC :

47 Country Singapore 14Microwave Oven type or grouping Domestic Please tick box if SS 146: Part 2: 10 : 1994 with A1 or SS 146 Part 2:10:1998 Relevant International IEC :1993 with Amendment 1 (1995) or IEC :1996 Extent of Alignment State reason if MOD 15Mobile split air conditioner 16Mixer, blender, mincer and similar appliances SS 146 Part 2:16:1998 IEC :1992 or IEC :1995 SS 146 Part 2: 13:1998 IEC :1984 with Amendment 1 (1989) & Amendment 2 (1990) or IEC : Refrigerator SS 146 Part 2:17:1998 IEC :1992 or IEC : Rice cooker SS 146 Part 2:2: 1997 IEC :1986 or IEC : Room Air Conditioner SS 146 Part 2:16:1998 IEC :1992 or IEC :1995 MOD Water temperature for ice maker from 15 to 25 C 20 Television/video display unit 21Table or standing fan SS 143: 1988 with A1 & A2 or SS 143 : 2000 IEC :1985 with Amendment 1 (1987) & Amendment 2 (1989) & Amendment 3 (1992) or IEC 60065:1998 SS 146 Part 2:18:2000 IEC (1997) MOD Subclause Replace "A load equals to 4 times" by "..10 times" 47

48 Country Singapore type or grouping Domestic Please tick box if 22Table lamp/standing lamp SS 263: Part 6: 1989 or SS 263 Part 6:2000 Relevant International IEC :1979 with Amendments 1,2 & 3 (1990) or IEC :1997 Extent of Alignment State reason if MOD 23Toaster, grill, roaster, hot plate and similar appliances SS 146 Part 2:15:1998 (applicable for toaster, grill, oven and similar appliances) IEC :1993 (applicable for toaster, grill, oven and similar appliances), IEC :1986 (applicable for hot plate and similar appliances) IEC (1993) with Amendment 1 and/or Amendment 2 (applicable for deep fryer, electric wok and similar appliances) 24Video cassette recorder 25Vacuum cleaner 26Washing machine 27Wall fan/ceiling fan 283pin rectangular type 13Amp Plug SS 143: 1988 with A1 & A2 or SS 143 : 2000 IEC :1985 with Amendment 1 (1987) & Amendment 2 (1989) & Amendment 3 (1992) or IEC 60065:1998 SS146:Part 2:4:1996 IEC :1993 SS146: Part 2:3:1995 IEC :1993 MOD Water temperature for normal operation from 15 to 25 C SS 146 Part 2:18:2000 & SS 360: 1992 subclause 5.7 & 5.8 (applicable for ceiling fan) IEC :1997 & [ SS 360 (1992) subclauses 5.7 & 5.8 applicable for Ceiling fan ] SS 145:Part 1:1997 based on BS 1363:Part 1:1995 MOD Subclause Replace "A load equals to 4 times" by "..10 times" 48

49 Country Singapore 29Fuses ( 13A) for use in plug 303pin round type 15amp plug 31Multiway Adaptors type or grouping Domestic Please tick box if 323pin Portable Socketoutlet 33Portable Cable Reels 34Instantaneous Electric Water Heater 35Mains Pressure Electric Storage Water Heater Relevant International Extent of Alignment SS 167:1977 based on BS 1362:1973 SS 472: 1999 based on BS 546: 1950 SS 246:1996 based on BS 1363:Part 3:1995 SS 145: Part 2:1997 based on BS 1363 Part 2:1995 SS 307:1996 based on Draft IEC 1242 document reference 23B (Central Office) 192 SS 146:Part 2:5: 1999 SS 146:Part 2:8: Residual Current Circuit Breaker (RCCB) SS 97: Part 1: pin 13amp socketoutlet SS 145: Part 2: pin round type 15amp socketoutlet SS 472: Domestic electric wall switch SS 227: Part 1: 2000 IEC :1997 IEC :1997 MOD MOD MOD based on BS 1363: Part 2: 1995 based on BS 546: 1950 IEC : 1998 State reason if MOD a) Bare heating element not allowed b) Water temperature from 15 to 25 C c) Water heater shall be at least IPX4 a) Bare heating element not allowed b) Additional markings requirements c) To incorporate pressure relief valve, thermostat and thermo cutout Incorporated national wiring code requirement. 49

50 Country type or grouping Domestic Please tick box if 40 Ballast for tubular fluorescent lamp 41 Isolating transformer for downlight fitting SS 490: Part 2: 8: 2001 (magnetic ballast) or SS 490: Part 2: 3: 2002 (electronic ballast) Relevant International IEC : 2000 IEC : 2000 IEC : 1997 or IEC : 2000 (electronic isolating transformer) Extent of Alignment State reason if MOD 50

51 Country Thailand 15 type or grouping Ballast for fluorescent lamps PVC insulated aluminium cables Domestic Please tick box if mandat ory Relevant International TIS (1978) IEC (1990), Am.1(1993), Am.2(1995) IEC 60921(1988), Am.1(1990), Am.2(1994) Extent of Alignment State reason if MOD NEQ TIS (1998) Electric irons TIS (1985) IEC (1993), Am.1(1999), Am.2(1999) Starters TIS (1985) IEC 60155(1993), for fluorescent Am.1(1995) lamps Incandescent lamps Lowvoltage distribution link fuses Lampholders for tubular fluorescent lamps and starterholders PVC insulated copper cables Fluorescent lamps : safety requirements TIS 4 Part (1986) IEC (1993) IEC (1999) NEQ NEQ NEQ TIS (1986) IEC (1998) NEQ TIS (1987) IEC (1999) NEQ TIS (1988) IEC (1993), Am.1(1995), Am.2(1998) IEC (1997) NEQ TIS (1990) IEC 60081:1997 NEQ 51

52 Country type or grouping Domestic Please tick box if Relevant International Extent of Alignment State reason if MOD Thailand 15 AC electric fans : safety requirements TIS (1990) IEC :1997 NEQ Electric stoves; open type heating elements : safety requirements TIS (1989) Mains operated electronic and related apparatus for household and similar general use : safety requirements TIS (1993) IEC 60065:1985 MOD TIS Subclause the current measured shall not exceed 0.3 ma (peak) Lighting and similar equipment : radio disturbance limits TIS (1999) CISPR 15:

53 Country type or grouping Thailand 15 Washing machines : safety requirements Domestic TIS (1997) Please tick box if Relevant International Extent of Alignment State reason if MOD IEC :1993 MOD TIS Subclause water temperature 45+5C. Subclause 4.7 ambient temperature 27+2C. Subclause 29.1 requirements on creepage distance, clearance and distance through insulation. Annex B.5 ambient temperature 27+2C, humidity 65+5%. 53

54 Country type or grouping Thailand 15 Tumbler dryers : safety requirements Domestic TIS (1996) Please tick box if Relevant International Extent of Alignment State reason if MOD IEC :1993 MOD TIS Subclause 1.1 Scope excluding rated voltage 480 V. Subclause temp. rise of the accessible front surface made of glass, ceramic and plastic pards. Subclause minimum crosssectional area of conductors of supply cords Subclause nominal crosssectional area of conductors. Subclause requirements on creepage distance, clearance and distance through insulation. 54

55 Country Viet Nam 4 According to certification Scheme 14 According to import, export certification Scheme type or grouping Domestic Pleas e tick box if mand atory Relevant Extent International Alignment Electric Kettle TCVN :2000 IEC335215:1995 and other and aments 1999 heating apparatuses with capacity not exceeding 10 litter Electric Fans TCVN :2000 IEC (includes desk 80:1997 fans, floor fans, wall fans) Electric Iron TCVN :2000 IEC33523:1993 and aments 1:1999 Electric TCVN :2000 IEC :1996 Hairdryers Fan: TCVN 56991:1998 IEC 3351:1991 (includes desk TCVN :1997 IEC fans, floor fans, 80:1997 wall fans, window fans, ceiling fans or roof fans, with electric motors, of a capacity not exceeding 125W ) Electric immersion sticks Storage Water Heaters Electric instantaneous water heaters Microwave Ovens Electric rice cookers Storage heating radiators TCVN 56991:1998 TCVN :2000 TCVN 56991:1998 TCVN :2001 TCVN 56991:1998 TCVN :2001 TCVN 56991:1998 TCVN :2001 TCVN IEC 3351:1991 IEC :1995 IEC 3351:1991 IEC :1989 IEC 3351:1991 IEC :1997 IEC 3351:1991 IEC :2001 TCVN 56991:1998 IEC 3351:1991 IEC of State reason if MOD 55

56 Electrothermic hairdressing apparatus TCVN 5699:1998 TCVN :2000 IEC 3351:1991 IEC :1996 Electric irons TCVN 56991:1998 TCVN :2000 IEC 3351:1991 IEC 33523:1993 Electric TCVN 64801:1999 IEC 6691:1993 Switches Knife switches TCVN 64801:1999 IEC 6691:1993 and reverse knifes witches One phase TCVN 61881:1996 IEC 8841:1994 electric sockets and Plugs TCVN 6190:1999 IEC 8841:1994 Electric Wires coated with PVC or PE TCVN 66101:2000 TCVN 66102:2000 TCVN 66103:2000 TCVN 66104:2000 TCVN 66105:2000 TCVN 66106:2000 TCVN 6612:2000 TCVN 6612A:2000 TCVN 66131:2000 TCVN 66141:2000 TCVN :2000 TCVN :2000 TCVN :2000 TCVN :2000 IEC 2271:1993 IEC :1997 IEC 2273:1993 IEC 2274:1992 IEC :1997 IEC 2276:1985 IEC 228:1978 IEC 228A:1982 IEC 3321:1993 IEC 81111:1993 IEC 81112:1985 IEC 81114:1985 IEC 81131:1985 IEC 81132:1985 Electric motors and generators (excluding generating units) TCVN 66271:2000 TCVN 66272:2001 TCVN 66272A:2001 IEC 341:2000 IEC 342:1972 Amd 1:1995 IEC 342A:1974 TCVN 66273:2000 IEC 343:1988 TCVN 66278:2000 TCVN 66279:2000 IEC 348:1972 Amd 1:1990 IEC 349:1990 Amd 1 :

57 V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES COUNTRY Brunei Darussalam TYPES OF CON FORMITY ASSESS MENT REGIMES Registration MODE OF REGULATION Suppliers registering products should register through the Procurement Section. Assessment Committee shall strictly review and analyse input information prior to endorsing approval of product registration based upon the mentioned requirements : Corporate information Quality and Performance (Quality Assurance details, test reports & certification carried out by International Test Bodies and representation of International used). Reliability and safety Maintenance management Track record Stock and delivery schedules After sale service Technical Presentation Cambodia ISC Mark Certification Treatment of Domestically Produced s: Application Assessment Type Test Assessment Awarding of Certificate Treatment for Import: I Registration / Type Approval for Imported s a Registration of Manufacturers 1 Application for registration attached with inspection data conducted by designated inspection bodies. 57

58 COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES 2 Issuing registration certificate MODE OF REGULATION Indonesia SNI Mark Certification b Type approval of products 1 application for type approval of products attached with testing reports conducted by designated testing laboratories ) 2 Issuing type approval certificate of the products 3 Manufacturers affix ISC mark on the products 4 Sale in Cambodian market 5 Surveillance II For the lot of Imported s (No Registration and Type Approval ) 1 Application for verification attached with testing reports conducted by designated testing laboratories 2 Issuing verification certificate 3 Affixing of ISC label 4 Sale in Cambodian market The Ministry of Industry and Trade through the Secretary General gazetted the procedure of SNI Mark product certification on June 1996 to ensure that the product meet the specified Indonesia National (SNI) requirements. There are two types of SNI i.e : Voluntary and Mandatory For the products, the producer/manufacturer has to fulfil two requirements i.e : 1. has to comply with the standard (SNI) 2. Mnufacturer has to implement one of the following modules which is based on Quality Management System i.e : Module I, BSN 10 Guidelines (16 elemenst/clause of ISO 9001) Module II, ISO 9003 Module III, ISO 9002 Module IV, ISO 9001 Module V, QMS which is equal to ISO

59 COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES MODE OF REGULATION Producers/manufacturers who wish to seek SNI mark certification have to send an application to Centre for Standardization and Accreditation (PSA) Ministry of Industry and Trade. Then PSA proceeds for evaluation of the application and verification to the manufacturers premises. PSA issued SNI certificate if they comply with the requirements This regime is only applied for domestic electrical and electronic products since Indonesia does not have technical regulation for imported electrical and electronic products. Clause 19 article (2) in Government Regulation No. 102/2000 of National Standardization stipulates import products must fulfil SNI Lao PDR NIL Regulation is yet to be implemented. The procedures for certification of products where certification is voluntary is as follows: Malaysia Registration/certificati on Application Assessment Type test Assessment Awarding of certification A certificate of approval is required. To obtain approval, the following are needed: Test reports from local or foreign laboratories which are acceptable to ST. 59

60 COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES MODE OF REGULATION Submission of Form ST (PE) 3, test report and certificate. Enter the SIRIM Certification Scheme/SIRIM Batch Testing Scheme (every consignment is subjected to inspection and testing) Use of SIRIM s label Myanmar Treatment of Domestically Produced Equipment s have to be registered at the Electrical Inspection Department. Treatment of Imports British and Japanese standards are used. Philippines Registration/ Certification Philippine Standard (PS) Quality and/or Safety Certification Mark Scheme These marks are awarded to domestic and foreign manufacturers that consistently comply with quality management system standards. These are awarded after a thorough assessment of the manufacturer based on ISO 9000 series standards. The products are also subjected to laboratory testing to verify compliance with PNS. Even after the issuance of the license to use PS certification marks, surveillance is regularly conducted. Treatment of Imports s covered by certification shall secure Import Commodity Clearance with BPS. Import shipment that meets product quality and safety requirements of the specific Philippine National is issued the Import Commodity Clearance Certificate. 60

61 COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES MODE OF REGULATION Singapore Registration The regulatory regime consists of two phases premarket approval and postmarket surveillance. There is a regulator intervention prior to the entry of the regulated products into the market. The controlled goods have to go through a structured process of approval, which starts with testing and ends with labelling. Please see Section VI Flowchart of Singapore's Regime. After entry into the market, SPRING Singapore conducts regular visits to shops and retail outlets to ensure that only approved controlled goods are displayed or offered for sale. Treatment of Controlled Goods Registration of controlled goods is based on certification by designated Conformity Assessment Bodies. Thailand Certification Certification System of TISI consists of two phases: 1. License Granting Granting a license is based on: 1.1 The results of tests which are conducted on products in accordance with the application standards. Consideration on this matter may be: (1) Acceptation of testing results, or (2) testing by designated laboratories, or (3) testing by testing at manufacturer s premises, or (4) testing by supervised manufacturer s testing. 1.2 The results of manufacturer s quality control system assessment according to specified conditions. Consideration on this matter may be: (1) Acceptation of quality system certificates, or 61

62 COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES MODE OF REGULATION (2) Factory visit for quality control system assessment, or (3) Manufacturer s quality control system assessment on technical file of factory. Vietnam Registration/Certificat ion 2. Surveillance After granting a license, the licensee will be followed up by: 2.1 sampling from factories for testing, 2.2 sampling from market for testing, 2.3 sampling for testing each import, 2.4 Factory visit for audit. The procedures for certification of those products where certification is is as follows: Application Plan for assessment Assessment of conformity to standards Type Test/ Testing result + Surveillance (local product) Assessment Awarding of Certification Surveillance 62

63 COUNTRY TYPES OF CON FORMITY ASSESS MENT REGIMES Registration/Import Export Goods Control The procedures for importexport goods control Application Type sampling Testing sample (s) Assessment Notification of control result MODE OF REGULATION 63

64 VI. FLOWCHART OF MEMBER COUNTRIES REGIME BRUNEI DARUSSALAM 64

65 CAMBODIA Ia Flowchart of Certification of Registration Foreign Manufacture, etc. Local Manufacture, etc. Request for Inspection Application for registration Application for Spot registration verification data registration and verification inspection Designated inspection bodies inspection data attached and document examination Department of Industrial of Cambodia Ministry of Industry, Mines and Energy Note:,, and are for accepting the testing data provided by designated inspection Bodies. and and are for other cases and for manufacturers in Cambodia 65

66 Ib Flowchart of Certification of Type Approval Foreign Manufacture, etc. Local Manufacture, etc. Request for Inspection Application for type Application for product Type verification data type approval approval type approval testing approval Specific foreign Testing institutes and inspection data attached Department of Industrial of Cambodia Ministry of Industry, Mines and Energy Foreign manufacturers, etc. Local manufacturers, etc. Affixing of standard mark by Manufacturers itself Imported product SALE Note:,, and are for accepting the testing data provided by designated testing laboratories., and are for other cases and for manufacturers in Cambodia 66

67 II Flowchart of Certification of Verification Foreign Manufacture, etc. Request for Inspection Application for Certification of verification data verification and verification inspection data Specific foreign attached Testing institutes Department of Industrial of Cambodia Ministry of Industry, Mines and Energy Affixing of standard mark by Department of Industrial of Cambodia SALE Note:,, and are for accepting the testing data provided by designated testing laboratories. 67

68 FLOWCHART OF INDONESIA S REGIME Diagrammatic Representation or flowchart of the regime Flow Chart of SNI Certification Process Incomplete 1 Applicant Administrative Disposition 2 Head of PSA Incomplete Incomplete 3 Head Of Accreditation Certification Process (Accreditation Division) Rej 4 Verification (Assessor) Module II, III, IV and V Process 14 days 6 Head of PSA 7 Administration 9 8 Company 68

69 MALAYSIA To apply for the Certificate of Approval from ST Submission of Form ST(PE 3), test reports and certificate. The test reports and certificate are from local / foreign laboratories which are recognized by ST/DSM (Department of Standard Malaysia) After obtaining Certificate of Approval (COA) from ST, applicant needs to enter the SIRIM Certification Scheme/SIRIM Batch Testing Scheme (every Consignment Test at SIRIM is subject to inspection and testing) Use of SIRIM s label. 69

70 PHILIPPINES PS Quality and/or Safety Certification Mark Scheme No Supplier s application for PS Certification Mark License to CAB Review of application Factory assessment assessment and inplant testing Independent testing Evaluation of Factory and Assessment reports Passed Yes Issuance of PS Mark License 70

71 Import Commodity Clearance Scheme Start Submission of Application Application Review Exempted Issuance of Certificate of Exemption With Test Certificate A Retest Denial: Destruction or Exportation Conditional Release Passed Issuance of ICC A Draw Samples for Testing/Re Testing Evaluation of Test Report/ Certificate 71

72 SINGAPORE Supplier applies to SPRING Singapore to be a Registered Supplier Registered Supplier submits Controlled Goods to a CAB (Local) or CAB (ForeignMRA) for Certification to SPRING Singapore safety standards requirements CAB (Local) or CAB (ForeignMRA) issues COC (valid for 3 years) to Registered Supplier after certifying the Controlled Goods Registered Supplier submits COC to SPRING Singapore for registration of the certified Controlled Goods SPRING Singapore issues acknowledgement to Registered Supplier and lists the controlled goods in the Register Registered Supplier affixes SAFETY Mark and commences supply of registered controlled goods The SAFETY Mark comprises of a safety logo enclosed in a square on the left and the word SAFETY MARK enclosed in a rectangle on the right. Below the logo is an unique certification number traceable to the registrant. The colour used is Pantone 287C Blue Colour. Registered Supplier submits the registered controlled goods to the CAB for recertification before COC expires 72

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

List of Harmonised Standards for EEE. Household and similar electrical appliances- Safety Part 1: General requirements

List of Harmonised Standards for EEE. Household and similar electrical appliances- Safety Part 1: General requirements Updated on 13 November 2015 List of Harmonised Standards for EEE *or any newer edition No. Agreed edition* of IEC Standards for ASEAN Harmonization Standard Title Scope of Standard 1 IEC 60065 Ed.7.0(2001)

More information

SINGAPORE I. RATIONALE FOR REGULATION. COUNTRY RATIONALE FOR REGULATION Singapore Consumer Protection II. REGULATION BODY

SINGAPORE I. RATIONALE FOR REGULATION. COUNTRY RATIONALE FOR REGULATION Singapore Consumer Protection II. REGULATION BODY As of June 2016 SINGAPORE I. RATIONALE FOR REGULATION COUNTRY RATIONALE FOR REGULATION Singapore Consumer Protection II. REGULATION BODY COUNTRY REGULATORY BODY Singapore SPRING Singapore III. LEGISLATIVE

More information

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

SINGAPORE I. RATIONALE FOR REGULATION. COUNTRY RATIONALE FOR REGULATION Singapore Consumer Protection II. REGULATION BODY

SINGAPORE I. RATIONALE FOR REGULATION. COUNTRY RATIONALE FOR REGULATION Singapore Consumer Protection II. REGULATION BODY As of October 2017 SINGAPORE I. RATIONALE FOR REGULATION COUNTRY RATIONALE FOR REGULATION Singapore Consumer Protection II. REGULATION BODY COUNTRY REGULATORY BODY Singapore SPRING Singapore III. LEGISLATIVE

More information

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

CONTROLLED GOODS AND THE APPLICABLE SAFETY STANDARDS PART I DOMESTIC OR HOUSEHOLD APPLIANCES AND SIMILAR ELECTRICAL APPLIANCES

CONTROLLED GOODS AND THE APPLICABLE SAFETY STANDARDS PART I DOMESTIC OR HOUSEHOLD APPLIANCES AND SIMILAR ELECTRICAL APPLIANCES CONTROLLED GOODS AND THE APPLICABLE SAFETY STANDARDS PART I DOMESTIC OR HOUSEHOLD APPLIANCES AND SIMILAR ELECTRICAL APPLIANCES 1 Hair Dryers 8516.31 MS IEC 60335-2-23 Household and similar electrical appliances-

More information

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

MUTUAL RECOGNITION ARRANGEMENT ON CONFORMITY ASSESSMENT OF ELECTRICAL AND ELECTRONIC EQUIPMENT. APEC EEMRA Information Interchange Format PART 1

MUTUAL RECOGNITION ARRANGEMENT ON CONFORMITY ASSESSMENT OF ELECTRICAL AND ELECTRONIC EQUIPMENT. APEC EEMRA Information Interchange Format PART 1 MUTUAL RECOGNITION ARRANGEMENT ON CONFORMITY ASSESSMENT OF ELECTRICAL AND ELECTRONIC EQUIPMENT APEC EEMRA Information Interchange Format PART 1 Introduction This format is being prepared to assist member

More information

THAILAND REGULATORY BODY LEGISLATIVE FRAMEWORK RATIONALE FOR REGULATION. Consumer Protection.

THAILAND REGULATORY BODY LEGISLATIVE FRAMEWORK RATIONALE FOR REGULATION. Consumer Protection. THAILAND I. RATIONALE FOR REGULATION COUNTRY RATIONALE FOR REGULATION Thailand Consumer Protection. II. REGULATION BODY COUNTRY Thailand REGULATORY BODY Thai Industrial tandards Institute (TII) under the

More information

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

THAILAND REGULATORY BODY LEGISLATIVE FRAMEWORK RATIONALE FOR REGULATION. Consumer Protection.

THAILAND REGULATORY BODY LEGISLATIVE FRAMEWORK RATIONALE FOR REGULATION. Consumer Protection. THAILAND I. RATIONALE FOR REGULATION COUNTRY RATIONALE FOR REGULATION Thailand Consumer Protection. II. REGULATION BODY COUNTRY Thailand REGULATORY BODY Thai Industrial tandards Institute (TII) under the

More information

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

Deemed to Comply Standards

Deemed to Comply Standards 1 of 5 28/10/2009 1:31 p.m. Deemed to Comply Standards Type of Product Standards Compliance with the appropriate product safety standards listed below, will satisfy the requirements of AS/NZS 3820 "Essential

More information

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

CRITICAL INTERPRETATION/ ADDITIONAL REQUIREMENTS WHERE LISTED STANDARDS ARE INSUFFICIENT/SILENT/VAGUE

CRITICAL INTERPRETATION/ ADDITIONAL REQUIREMENTS WHERE LISTED STANDARDS ARE INSUFFICIENT/SILENT/VAGUE As of April 2017 CRITICAL INTERPRETATION/ ADDITIONAL REQUIREMENTS WHERE LISTED STANDARDS ARE INSUFFICIENT/SILENT/VAGUE Member Product 1 Applied Clause/s Issues/Concerns Critical Interpretation Additional

More information

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

INDONESIA REGULATORY BODY. as of 3 November 2017 I. COUNTRIES WITH MANDATORY STANDARDS FOR GOVERNMENT PROCUREMENT ONLY RATIONALE FOR REGULATION

INDONESIA REGULATORY BODY. as of 3 November 2017 I. COUNTRIES WITH MANDATORY STANDARDS FOR GOVERNMENT PROCUREMENT ONLY RATIONALE FOR REGULATION I. COUNTRIES WITH MANDATORY STANDARDS FOR GOVERNMENT PROCUREMENT ONLY INDONESIA I. RATIONALE FOR REGULATION COUNTRY RATIONALE FOR REGULATION Indonesia Consumer Protection II. REGULATION BODY COUNTRY REGULATORY

More information

Government Notices

Government Notices Government Notice No. 200 of 2017 Government Notices 2017 1265 THE CONSUMER PROTECTION ACT Regulations made by the Minister under section 4 of the Consumer Protection Act 1. These regulations may be cited

More information

Controlled Goods Definitions Safety Standards

Controlled Goods Definitions Safety Standards CONTROLLED GOODS AND THEIR APPLICABLE SAFETY STANDARDS Low Risk Controlled Goods Definitions Safety Standards Air cooler Air cooler, which is an electrical appliance intended f household use to agitate

More information

Consumer Protection (Safety Requirements) (Amendment) Regulations 2017

Consumer Protection (Safety Requirements) (Amendment) Regulations 2017 Consumer Protection (Safety Requirements) (Amendment) Regulations 2017 GN No. 200 of 2017 Government Gazette of Mauritius No. 95 of 7 October 2017 THE CONSUMER PROTECTION ACT Regulations made by the Minister

More information

10.6 Schedule of Accreditation

10.6 Schedule of Accreditation Product Certification Body Accreditation is accredited by the GCC Accreditation Center () in accordance with the recognized International Standard, Conformity assessment -- Requirements for bodies certifying

More information

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

Declaring Definitions for Electrical Products 7 March 2014

Declaring Definitions for Electrical Products 7 March 2014 Page 1 of 11 Regulatory definitions for Australia and New Zealand This document sets out the regulatory definitions of: The Declared Articles under the NSW Electricity (Consumer Safety) Act 2004; and Level

More information

Customs Procedures. (Import & Export) Control on importation of electrical appliances and. accessories

Customs Procedures. (Import & Export) Control on importation of electrical appliances and. accessories Control on importation of electrical appliances and Customs Procedures accessories (Import & Export) Consumer Protection (Safety Requirements) Regulations 2017 Presented by: MRA Customs 1st March 2017

More information

... II.. s::. U II!.! 0 I Q I! n) ~}.St.ll ~I Jq~ (Jql.siLII U" I? o Jq~ GCC Standardization Organization. Designation of a Notified Body

... II.. s::. U II!.! 0 I Q I! n) ~}.St.ll ~I Jq~ (Jql.siLII U I? o Jq~ GCC Standardization Organization. Designation of a Notified Body ... II.. s::. U II!.! 0 I Q I! n) ~}.St.ll ~I Jq~ (Jql.siLII U" I? o Jq~ GCC Standardization Organization Designation of a Notified Body The GCC Standardization Organization (GSO) hereby affirms that Bureau

More information

... II.. s:. U".!.! 0 I a'.! n) '4-!J..SZ.ll ~~ Jq~ (Jql.sii.JI u l?o Jq~ GCC Standardization Organization. Designation of a Notified Body

... II.. s:. U.!.! 0 I a'.! n) '4-!J..SZ.ll ~~ Jq~ (Jql.sii.JI u l?o Jq~ GCC Standardization Organization. Designation of a Notified Body .... II.. s:. U".!.! 0 I a'.! n) '4-!J..SZ.ll ~~ Jq~ (Jql.sii.JI u l?o Jq~ GCC Standardization Organization Designation of a Notified Body The GCC Standardization Organization (GSO) hereby affirms that

More information

24 (Second Section) OFFICIAL BULLETIN Friday, September 10, 2010

24 (Second Section) OFFICIAL BULLETIN Friday, September 10, 2010 24 (Second Section) OFFICIAL BULLETIN Friday, September 10, 2010 SECRETARY OF ENERGY The CATALOG of equipment and appliances used by manufacturers, importers, distributors and marketers that require mandatory

More information

10.6 Schedule of Accreditation

10.6 Schedule of Accreditation Product Certification Body Accreditation is accredited by the GCC Accreditation Center () in accordance with the recognized International Standard, Conformity assessment -- Requirements for bodies certifying

More information

Notice That Particular Low Voltage or Extra-low Voltage Fittings or Appliances are Declared Medium Risk Articles

Notice That Particular Low Voltage or Extra-low Voltage Fittings or Appliances are Declared Medium Risk Articles Notice That Particular Low Voltage or Extra-low Voltage Fittings or Appliances are Declared Medium Risk Articles Pursuant to Regulation 83 of the Electricity (Safety) Regulations 2010, I, Mark Stephen

More information

NSW Government Notice

NSW Government Notice Schedule 1 Declared Electrical Articles Interpretation: In this schedule a reference to- AS/NZS 60335.1 means AS/NZS 60335.1:2011+A1-3; AS/NZS 3100 means AS/NZS 3100:2009+A1-4; AS/NZS 60745.1 means AS/NZS

More information

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 1

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 1 EUROFINS PRODUCT SERVICE (THAILAND) CO., LTD 344/2 Soi Soonvijai 4, Rama 9 Rd., Bangkapi, Huaykwang, Bangkok, 10320 THAILAND Mr. Dirk Fleischer (Quality Manager

More information

Declaring Definitions for Electrical Products Gazetted: 18 November 2016

Declaring Definitions for Electrical Products Gazetted: 18 November 2016 Page 1 of 12 Regulatory definitions for Australia and New Zealand This document sets out the regulatory definitions of: The Declared Articles under the NSW Electricity (Consumer Safety) Act 2004; and Reference

More information

Listing of standards providing presumption of conformity for List (2) products under Regulation BD

Listing of standards providing presumption of conformity for List (2) products under Regulation BD BD-142004-01 List Standards Listing Listing of standards providing presumption of conformity for List products under Regulation BD-142004-01 Ed. 1.0 -February 2018 2018-02-18 The standard references below

More information

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 EUROFINS PRODUCT SERVICE (THAILAND) CO., LTD. 1 344/2 Soi Soonvijai 4, Rama 9 Rd., Bangkapi, Huaykwang, Bangkok, 10320 Thailand Mr. Dirk Fleischer (Quality

More information

22 (Second Section) OFFICIAL JOURNAL Friday, September 10th, 2010 MINISTRY OF ENERGY

22 (Second Section) OFFICIAL JOURNAL Friday, September 10th, 2010 MINISTRY OF ENERGY 22 (Second Section) OFFICIAL JOURNAL Friday, September 10th, 2010 MINISTRY OF ENERGY CATALOG of equipment and appliances for which manufacturers, importers, suppliers, and distributors must include energy

More information

10.6 Schedule of Accreditation

10.6 Schedule of Accreditation Accreditation Manager: Product Certification Body Accreditation is accredited by the GCC Accreditation Center () in accordance with the recognized International Standard, Conformity assessment -- Requirements

More information

CONFORMITY ASSESSMENT OF LOW VOLTAGE DEVICES (LVD) AND TOYS AS PER GSO TECHNICAL REGULATIONS

CONFORMITY ASSESSMENT OF LOW VOLTAGE DEVICES (LVD) AND TOYS AS PER GSO TECHNICAL REGULATIONS GUIDELINES OF IMPORTS FOR THE TRADE CONFORMITY ASSESSMENT OF LOW VOLTAGE DEVICES (LVD) AND TOYS AS PER GSO TECHNICAL REGULATIONS This data sheet has been prepared specifically in respect of exports to

More information

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES

ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES ASEAN SECTORAL MRA ON ELECTRICAL AND ELECTRONIC EQUIPMENT (ASEAN EE MRA) LISTING OF THE DESIGNATED CONFORMITY ASSESSMENT BODIES In accordance to the ASEAN Sectoral MRA for Electrical and Electronic Equipment,

More information

10.6 Schedule of Accreditation

10.6 Schedule of Accreditation Product Certification Body Accreditation is accredited by the GCC Accreditation Center () in accordance with the recognized International Standard, Conformity assessment -- for bodies certifying products,

More information

10.6 Schedule of Accreditation

10.6 Schedule of Accreditation Accreditation Manager: Product Certification Body Accreditation is accredited by the GCC Accreditation Center () in accordance with the recognized International Standard, Conformity assessment -- Requirements

More information

PROVINCE OF BRITISH COLUMBIA ORDER OF THE LIEUTENANT GOVERNOR IN COUNCIL

PROVINCE OF BRITISH COLUMBIA ORDER OF THE LIEUTENANT GOVERNOR IN COUNCIL PROVINCE OF BRITISH COLUMBIA ORDER OF THE LIEUTENANT GOVERNOR IN COUNCIL Order in Council No. 691, Approved and Ordered DEC 1 0 200q Lieutenant Governor Executive Council Chambers, Victoria On the recommendation

More information

- Full test except clause (IPX1 IPX2) (Oxygen bomb test) and annex ต

- Full test except clause (IPX1 IPX2) (Oxygen bomb test) and annex ต Laboratory name Japan Electrical Testing Laboratory (Thailand) Co., Ltd. Address 46/173 Nuanchan Road, Nuanchan, Bueng Kum, Bangkok 1. A.C. electric fans - TIS 934-2533 (1990) - TIS 934-2558 (2015) 2.

More information

ANNEX. to the. Proposal for a Council Decision. on the conclusion of the Free Trade Agreement between the European Union and the Republic of Singapore

ANNEX. to the. Proposal for a Council Decision. on the conclusion of the Free Trade Agreement between the European Union and the Republic of Singapore EUROPEAN COMMISSION Brussels, 18.4.2018 COM(2018) 196 final ANNEX 3 ANNEX to the Proposal for a Council Decision on the conclusion of the Free Trade Agreement between the European Union and the Republic

More information

PROVINCE OF BRITISH COLUMBIA ORDER OF THE LIEUTENANT GOVERNOR IN COUNCIL

PROVINCE OF BRITISH COLUMBIA ORDER OF THE LIEUTENANT GOVERNOR IN COUNCIL PROVINCE OF BRITISH COLUMBIA ORDER OF THE LIEUTENANT GOVERNOR IN COUNCIL Order in Council No. 900 Approved and Ordered DEC - 8 2008 Executive Council Chambers, Victoria Lieutenant Governor On the recommendation

More information

DETAIL OF NOTIFICATION SCOPE GSO Technical Regulation. Gulf Technical Regulation for Low Voltage Electrical Equipment and Appliances (BD )).

DETAIL OF NOTIFICATION SCOPE GSO Technical Regulation. Gulf Technical Regulation for Low Voltage Electrical Equipment and Appliances (BD )). Locations where notification activities covered: Address: 10, Chungui-ro, Jinju-si, Gyeongsangnam-do, 52852, Rep. of KOREA Contact: Lee Won Bok Telephone: +82 2 860 1306 Facsimile: +82 2 860 1339 Email:

More information

First Catalogue of Products Subject to Compulsory Certification

First Catalogue of Products Subject to Compulsory Certification First Catalogue of Products Subject to Compulsory Certification 1. Electrical wires and cables ( total 5 categories ) Cord sets, Flexible rubber-sheathed cables for mining purposes, Insulated cables (wires)

More information

INDONESIAN MANDATORY EE STANDARDS (26 Products) as of 12 Feb 2016

INDONESIAN MANDATORY EE STANDARDS (26 Products) as of 12 Feb 2016 INDONEIAN MANDATORY EE TANDARD (26 Products) as of 12 Feb 2016 Domestic tandards mandaty TANDARD tandards Incandescent lamps NI 04-3560-1994 V IEC 60064 Ed.6 (1993-12) elf-ballast lamp f general lighting

More information

CONFORMITY ASSESSMENT OF LOW VOLTAGE DEVICES (LVD) AND TOYS AS PER GSO TECHNICAL REGULATIONS

CONFORMITY ASSESSMENT OF LOW VOLTAGE DEVICES (LVD) AND TOYS AS PER GSO TECHNICAL REGULATIONS GUIDELINES OF IMPORTS FOR THE TRADE CONFORMITY ASSESSMENT OF LOW VOLTAGE DEVICES (LVD) AND TOYS AS PER GSO TECHNICAL REGULATIONS This data sheet has been prepared specifically in respect of exports to

More information

Waste Electrical and Electronic Equipment Declaration Form 2019

Waste Electrical and Electronic Equipment Declaration Form 2019 Waste Electrical and Electronic Equipment Declaration Form 2019 Company Name Address Contact Person VAT Reg. no. email Contact Telephone 1. Temperature Exchange Equipment Refrigerators Combined refrigerators-freezers

More information

LIST OF PUBLISHED STANDARDS

LIST OF PUBLISHED STANDARDS Report : 08-0-0 Page o : Of 5 LST OF PUBLSHED STDRDS Total Count: 9 SS nt pproved mendment SBS/TC 07 SS 60065:05/EC 60065:0 7. udio, video and similar electronic apparatus 05-0- - Safety requirements 00-0-

More information

10.6 Scope of Accreditation

10.6 Scope of Accreditation Testing Laboratory Accreditation is accredited by the GCC Accreditation Center () in accordance with the recognised International Standard, General requirements for the competence of testing and calibration

More information

(Notices) EUROPEAN COMMISSION

(Notices) EUROPEAN COMMISSION 14.8.2012 Official Journal of the European Union C 245/1 IV (Notices) NOTICES FROM EUROPEAN UNION INSTITUTIONS, BODIES, OFFICES AND AGENCIES EUROPEAN COMMISSION Commission communication in the framework

More information

NB VDE Testing and Certification Institute. Schedule of Notification

NB VDE Testing and Certification Institute. Schedule of Notification Locations where notification activities covered: Address: MerianStrasse 28, 63069 Offenbach, Germany Contact: Mr Wolfgang NIEDZIELLA Tel: +49 69 8306-0 Fax: +49 69 8306-555 Email: vde-institute@vde.com

More information

Regulatory definitions for Australia and New Zealand

Regulatory definitions for Australia and New Zealand Page 1 of 16 Regulatory definitions for Australia and New Zealand This document sets out the regulatory definitions of: The Declared Articles for REAS under the NSW Electricity (Consumer Safety) Act 2004;

More information

Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK

Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK Product Test Centre 15 Progress Road Eastwood Leigh-on-Sea Essex SS9 5JA Contact: Mr S Bailey Tel: +44 (0)1702 425738 E-Mail: stuart.bailey@honeywell.com

More information

Annex 2. Indicative list of electrical and electronic equipment which falls within the categories in Annex 1 and under the fractions in section 27(1).

Annex 2. Indicative list of electrical and electronic equipment which falls within the categories in Annex 1 and under the fractions in section 27(1). From; Statutory Order on placing on the market of electrical and electronic equipment and management of waste electrical and electronic equipment no. 130, 6. feb. 2014 Annex 2 Indicative list of electrical

More information

De accreditatie werd uitgereikt aan/ L'accréditation est délivrée à/ The accreditation is granted to/ Die akkreditierung wurde erteilt für:

De accreditatie werd uitgereikt aan/ L'accréditation est délivrée à/ The accreditation is granted to/ Die akkreditierung wurde erteilt für: Bijlage bij accreditatie-certificaat Annexe au certificat d'accréditation Annex to the accreditation certificate Beilage zur Akkreditatierungszertifikat 472-TEST NBN EN ISO/IEC 17025:2005 Versie/Version/Fassung

More information

Annex to the Accreditation Certificate D-PL according to DIN EN ISO/IEC 17025:2005

Annex to the Accreditation Certificate D-PL according to DIN EN ISO/IEC 17025:2005 Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D-PL-19065-02-00 according to DIN EN ISO/IEC 17025:2005 Period of validity: 2017-05-23 to 2022-05-22 Date of issue: 2017-05-23

More information

home energy consumption list A list of electric household appliances, and their operating cost northlandutilities.com

home energy consumption list A list of electric household appliances, and their operating cost northlandutilities.com 3 7 home energy consumption list 8 4 A list of electric household appliances, and their operating cost 6 3 9 1 5 9 2 northlandutilities.com 4 Helping Northerners make wise electricity choices electricity

More information

Information Booklet 2002 Edition

Information Booklet 2002 Edition SINGAPORE CONSUMER PROTECTION (SAFETY REQUIREMENTS) Information Booklet 2002 Edition (version 3) (established since 1991) 2002 Standards, Productivity and Innovation Board SPRING Singapore 2 Bukit Merah

More information

10.6 Schedule of Accreditation

10.6 Schedule of Accreditation Certification Body Accreditation is accredited by the GCC Accreditation Center () in accordance with the recognized International Standard, Conformity assessment -- Requirements for bodies certifying products,

More information

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 TUV RHEINLAND OF NORTH AMERICA, INC. 12 Commerce Road Newtown, CT 06470 Mr. Bruce Fagley: 203 426 0888 x119 Email: bfagley@us.tuv.com www.tuv.com ELECTRICAL

More information

Performance of household electrical appliances-refrigerating. EN Domestic cooking appliances burning gas - Part 1-1: Safety - General

Performance of household electrical appliances-refrigerating. EN Domestic cooking appliances burning gas - Part 1-1: Safety - General IAS Accreditation Number Company Name Address Contact Name TL-601 Baglar Mah. Osmanpasa Cad. No: 95 Is Istanbul Plaza E Girişi 34209 Gunesli Istanbul Turkey Ms. Muge Okumus E&E Section Manager Telephone

More information

Gas-fired water heaters, volume III, storage water heaters with input ratings above 75,000 Btu per hour, circulating and instantaneous

Gas-fired water heaters, volume III, storage water heaters with input ratings above 75,000 Btu per hour, circulating and instantaneous IAS Accreditation Number Company Name Address TL-657 Room 209, No. 46, Nanxiang 3 rd Road Science City Development Zone Guangzhou 510663 People s Republic of China Javen Xuan, Quality Manager Contact Name

More information

K W H - I N 1 H o t S p l a s h I N S TA N T W AT E R G E Y S E R

K W H - I N 1 H o t S p l a s h I N S TA N T W AT E R G E Y S E R K W H - I N 1 H o t S p l a s h I N S TA N T W AT E R G E Y S E R Dear Customer, Congratulations! Thank you for buying this KORYO appliance. Your new Water Heater has been designed for your convenience.

More information

NZECP 19: 1994 ISSN COVER PAGE

NZECP 19: 1994 ISSN COVER PAGE NZECP 19: 1994 ISSN 0114-0663 COVER PAGE NZECP:19 1994 NEW ZEALAND ELECTRICAL CODE OF PRACTICE for DETERMINATION OF MAXIMUM DEMAND in ELECTRICAL INSTALLATIONS Issued by the Office of The Chief Electrical

More information

Update Note on the Disposal of Waste Electrical and Electronic Equipment (WEEE)

Update Note on the Disposal of Waste Electrical and Electronic Equipment (WEEE) The Update Note on the Disposal of Waste Electrical and Electronic Equipment (WEEE) Background The Waste Electrical and Electronic Equipment (WEEE) Regulations came into force across the UK on 5 January

More information

AS/NZS IEC :2013

AS/NZS IEC :2013 AS/NZS IEC 61347.2.13:2013 (IEC 61347-2-13, Ed.1.0 2006, MOD) Australian/New Zealand Standard Lamp controlgear Part 2.13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED

More information

Products Under Mandatory Certification HOUSEHOLD APPLIANCES. Philippine National Standard (PNS) No. PNS IEC :2015 (IEC published 2015)

Products Under Mandatory Certification HOUSEHOLD APPLIANCES. Philippine National Standard (PNS) No. PNS IEC :2015 (IEC published 2015) Products Under Mandatory Certification HOUSEHOLD APPLIANCES 1 Electric fans PNS IEC 60335-2-80:2015 (IEC published 2015) similar electrical appliances Part 2 : Particular requirements for fans Plastic/Metal

More information

G-Marking Low Voltage Electrical Equipment & Appliances. GCC-GSO Conformity Assessment Scheme (RCAS)

G-Marking Low Voltage Electrical Equipment & Appliances. GCC-GSO Conformity Assessment Scheme (RCAS) G-Marking Low Voltage Electrical Equipment & Appliances GCC-GSO Conformity Assessment Scheme (RCAS) 1 Agenda TOPIC G-Marking Scheme Overview G-Marking Now and Post July 2016 Affected Products, Standards,

More information

CITY OF BARTOW (COB)

CITY OF BARTOW (COB) CITY OF BARTOW (COB) WATT CHOPPER knows how to take a bite out of your electric bill and save both energy and money... 5 Quick Steps for you to Conserve Energy Today... 1. CHANGE A LIGHT Replace three

More information

Use numbers given in the box to complete the following sentences. In the UK, the mains electricity supply is volts.

Use numbers given in the box to complete the following sentences. In the UK, the mains electricity supply is volts. DOMESTIC USES AND SAFETY PART II Q1. Use numbers given in the box to complete the following sentences. 12 50 110 230 In the UK, the mains electricity supply is volts. The frequency of the UK mains electricity

More information

Wattage Estimation Guide

Wattage Estimation Guide Estimation Guide Tip: Don't just add up the total wattage for everything you want to power. See the section on power management to learn how to use a smaller generator to power more. Home Applications

More information

2012/SCSC/WKSP4/018 Barriers of Applying International Program for ICT Products

2012/SCSC/WKSP4/018 Barriers of Applying International Program for ICT Products 2012/SCSC/WKSP4/018 Program for ICT Products Submitted by: Korea Energy Management Corporation (KEMCO) Aligning Energy Efficiency Regulations for ICT Products: Developing a Strategic Approach Seoul, Korea

More information

REGULATORY ENVIRONMENT ON ELECTRICAL AND ELECTRONIC PRODUCTS IN MALAYSIA. Table of Contents

REGULATORY ENVIRONMENT ON ELECTRICAL AND ELECTRONIC PRODUCTS IN MALAYSIA. Table of Contents REGULATORY ENVIRONMENT ON ELECTRICAL AND ELECTRONIC PRODUCT IN MALAYIA Table of Contents I. Rationale for Regulation II. III. IV. Regulatory Authority Legislative Framework Mandatory tandards V. Mode of

More information

Title. Rev. 3 of 09/04/2018. Revision and date entry into force. PR.PART. PRD/GMARK Rev. 3 of 09/04/2018 Page 1 di 36 Mod. 3268/1

Title. Rev. 3 of 09/04/2018. Revision and date entry into force. PR.PART. PRD/GMARK Rev. 3 of 09/04/2018 Page 1 di 36 Mod. 3268/1 Title SPECIAL REQUIREMENTS FOR THE ISSUING OF GULF-TYPE EXAMINATION CERTIFICATES IN THE FRAME OF THE STANDARDIZATION ORGANIZATION FOR THE COOPERATION COUNCIL FOR THE ARAB STATES OF THE GULF (GSO) Reference

More information

Anti-Counterfeiting Measures on Electrical Appliances in Japan

Anti-Counterfeiting Measures on Electrical Appliances in Japan Anti-Counterfeiting Measures on Electrical Appliances in Japan Seiichi Matsuo Forum of Electrical Safety Inspection Associations, Japan 1 1 Locations of Electrical Safety Inspection Associations in Japan

More information

Energy Use Rationalization Act

Energy Use Rationalization Act Energy Use Rationalization Act 3 Energy Efficiency Labeling and Standard Mandatory labeling Applying MEPS e-standby Power Voluntary reporting High-efficiency Electric Product Certification Voluntary certification

More information

SUPPLIER FAMILY qty MEDISANA ACUPUNCTURE 8 LAICA AEROSOL 7 LAICA AEROSOL 836 MEDISANA AEROSOL 1 MIXT VARIOUS BRANDS UK AUDIO 1 MIXT VARIOUS BRANDS UK AUDIO 1 ADE BATH SCALE 16 MIXT VARIOUS BRANDS UK BATH

More information

KUWAIT CONFORMITY ASSURANCE SCHEME

KUWAIT CONFORMITY ASSURANCE SCHEME TECHNICAL INSPECTION REPORT (TIR) CERTIFICATE FOR GOODS TO BE EXPORTED TO STATE OF KUWAIT GUIDELINES OF IMPORTS FOR THE TRADE KUWAIT CONFORMITY ASSURANCE SCHEME This data sheet has been prepared specifically

More information

Safety Standards for Electronic Products

Safety Standards for Electronic Products Safety Standards for Electronic Products The following are some of the safety standards for all types of electronic products. ANSI C95.3:1972 / Techniques & instrumentation for measurement of potentially

More information

EN Light And Lighting - Measurement And Presentation Of Photometric Data Of Lamps And Luminaires - Part 1: Measurement And File Format

EN Light And Lighting - Measurement And Presentation Of Photometric Data Of Lamps And Luminaires - Part 1: Measurement And File Format IAS Accreditation Number TL-553 Company Name Address Via delle Industrie 5 & 6, 20061 Carugate (MI), Italy Contact Name Dario Rivoltella, Laboratory Manager Telephone +39 02 92526427 Effective Date of

More information

Fluorescent Lamps - Guide for Electrical Measurements

Fluorescent Lamps - Guide for Electrical Measurements IAS Accreditation Number TL-471 Company Name UL-CCIC Company Limited Address No. 2, Chengwan Road Suzhou Industrial Park Suzhou 215122 People s Republic of China Contact Name Antonio Zhang, Laboratory

More information

U.S. Census Bureau Electric Housewares and Fans MA335E(07) Issued May 2008

U.S. Census Bureau Electric Housewares and Fans MA335E(07) Issued May 2008 U.S. Census Bureau Electric Housewares and Fans - 2007 MA335E(07) Issued May 2008 Address inquiries concerning these data to Consumer Goods Industries Branch, U.S. Department of Commerce, Census Bureau,

More information

EU Declaration of Conformity Annex

EU Declaration of Conformity Annex EU Declaration of Conformity Annex Document number: 2016 / 9C1-3423710-EN-00 The conformity of the designated product(s) with the provisions of the European radio equipment Directive is given by the compliance

More information

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 TÜV SÜD CERTIFICATION AND TESTING (CHINA) CO., LTD. 1 SHANGHAI BRANCH 3-13 F No. 151 Heng Tong Road Shanghai, 200 070, People's Republic of China Testing Location:

More information

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 COSMOS CORPORATION 1 718-1, Katsurase-Cho Matsusaka-shi, Mie 515-1104 JAPAN Akira Sakai (Authorized Representative) +81 598-30-6211 sakai-akira@cosmos-corp.com

More information

Energy Efficiency Standards for Electric Fans

Energy Efficiency Standards for Electric Fans Energy Efficiency Standards & Labels for Residential Appliances EES&L 2 nd. Phase Energy Efficiency Standards for Electric Fans Eng. Khaled Zahran City Star Hotel-Cairo 22 May 2014 Electricity Consumption

More information

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 AUSTEST LABORATORIES MELBOURNE 53 Latitude Blvd. Thomastown, Victoria, 3074, Australia Martin Garwood Phone: +61 (0)3 9464 4016 Fax: +61 (0)3 9464 0687 ELECTRICAL

More information

Catalogue of CCC Aug, 2006

Catalogue of CCC Aug, 2006 Catalogue of CCC Aug, 2006 1 st Catalogue mandatory from August 1, 2003 2 nd Catalogue mandatory from August 1, 2005 Decoration Material 3 rd Catalogue mandatory from October 1, 2005 Security Technology

More information

Authorised Collection Point CODE OF PRACTICE

Authorised Collection Point CODE OF PRACTICE Authorised Collection Point CODE OF PRACTICE Health & Safety It is the Sites responsibility to ensure that all loading & unloading takes place in a safe manner. The material should always be stored in

More information

Energy Efficiency Labelling

Energy Efficiency Labelling THE KINGDOM OF SAUDI ARABIA IMPORT GUIDE No 02 Energy Efficiency Labelling Important Note : this Import Guide is intended to give Bureau Veritas Customers essential information as reference related to

More information

Put on the market 1 Production Export. EEE used in households 3 = The obligations 4 to show visibly "RF" YES YES YES YES YES YES YES YES YES YES

Put on the market 1 Production Export. EEE used in households 3 = The obligations 4 to show visibly RF YES YES YES YES YES YES YES YES YES YES 1. 1.1.1 Ventilators and hot air ventilators except bathroom ventilators, heaters, convectors, portable mini washing machines, accessories to large household appliances 1.1.2 Unclassified large household

More information

INTERNATIONAL STANDARD

INTERNATIONAL STANDARD INTERNATIONAL STANDARD IEC 60598-1 Edition 6.1 2006-09 Edition 6:2003 consolidated with amendment 1:2006 Luminaires Part 1: General requirements and tests This English-language version is derived from

More information

United Arab Emirates Emirates Conformity Assessment Scheme & Emirates Quality Mark

United Arab Emirates Emirates Conformity Assessment Scheme & Emirates Quality Mark GUIDELINES OF IMPORTS FOR THE TRADE United Arab Emirates United Arab Emirates Emirates Conformity Assessment Scheme & Emirates Quality Mark This data sheet has been prepared specifically in respect of

More information

Resource efficiency and Circular Economy in the EU and Japan Overview of the EU Ecodesign and Energy Labelling schemes. Tokyo, 15 February 2016

Resource efficiency and Circular Economy in the EU and Japan Overview of the EU Ecodesign and Energy Labelling schemes. Tokyo, 15 February 2016 Resource efficiency and Circular Economy in the EU and Japan Overview of the EU Ecodesign and Energy Labelling schemes Tokyo, 15 February 2016 Policy context Europe 2020 Strategy: objectives on employment,

More information

13799 Commerce Parkway Richmond, British Columbia V6V 2N9 Canada Benjamin Barker, Senior Manager Accreditations

13799 Commerce Parkway Richmond, British Columbia V6V 2N9 Canada Benjamin Barker, Senior Manager Accreditations IAS Accreditation Number Company Name Address Contact Name Telephone (604) 273-4581 Effective Date of Scope February 9, 2018 Accreditation Standard ISO/IEC 17025:2005 TL-270 - Vancouver 13799 Commerce

More information

UGANDA NATIONAL BUREAU OF STANDARDS EXPORTER AND IMPORTER GUIDELINES APPENDIX B REGULATED PRODUCT LIST PRODUCTS SUBJECT TO PVOC PROGRAMME (COVERED)

UGANDA NATIONAL BUREAU OF STANDARDS EXPORTER AND IMPORTER GUIDELINES APPENDIX B REGULATED PRODUCT LIST PRODUCTS SUBJECT TO PVOC PROGRAMME (COVERED) PRODUCTS SUBJECT TO PVOC PROGRAMME (COVERED) GROUP I TOYS I-01 Dolls representing only human beings-dolls, whether or not dressed 9502.10.00 US ISO 4210 Cycles Safety requirements for bicycles US ISO 8124-1:2005

More information