Metasys Integrator Airflow Application

Size: px
Start display at page:

Download "Metasys Integrator Airflow Application"

Transcription

1 Metasys Connectivity Technical Manual 69. Metasys Integrator Section Application Note Issue Date 0998 APPLICATION NOTE Metasys Integrator Airflow Application lntroduction Page Application Details * Component Requirements *6 Vendor Contact Information 8 Design Considerations *9 Cable Connections Cable Pinouts * Connecting the Cable * Metasys Integrator Setup Point Mapping Tables 7 Dataguard III Commissioning Tool Labels (Generic Model) 7 DATAC DX Series Dash x0 9 DATAC CG Series Dash x0 DATAC CW Series Dash x0 Drycell Series Dash x04 DATAC Mainframe Chiller Series Dash x0 7 DATAC DX Retrofit Series Dash x07 9 DATAC CW Retrofit Series Dash x08 CCT DX with Hot Gas Bypass Dash x09 TELAC Series Dash x * Indicates those sections where changes have occurred since the last printing. 998 Johnson Controls, Inc. Code No. LIT

2 DATAC CG Series Dash x Page 7 DATAC DX Series Dash x 9 Tech Cool Dash Series 4x0, 4x0 Controller Points *4 CG Series Dash 4x0, 4x06 Points *44 CW Series Dash 4x0, 4x07 Points *47 Main Frame Chiller Series Dash 4x0 Points *49 CCT DX Series Dash 4x06, 4x08 Points * Drycell Series Dash 4x08 Points Ceiling Mounted Unit Dash 4x04, 4x0 Points *7 AFX Series Dash 4x09, 4x00, 4x0, 4x04 Points *60 Metasys Network Setup 6 Mapping to a CS Object *6 Custom Integration *6 * indicates those sections where changes have occurred since the last printing. Metasys Integrator Metasys Integrator Airflow Application

3 lntroduction This document explains Metasys Integrator Airflow applications. Use this document with the Metasys Integrator Technical Bulletin (LIT-690) in the Metasys Connectivity Technical Manual (FAN 69.), which provides information on installing and commissioning Metasys Integrator. For information on Airflow equipment, see Airflow documentation (obtainable from an Airflow representative). Application Details Metasys Integrator allows Airflow equipment to become an integral part of the Metasys and Metasys Companion Networks. Once Airflow Dataguard controllers are connected to a Metasys or Companion Network via the Metasys Integrator, their data is accessible to the full complement of Metasys Facility Management System (FMS) features, including Change-of-State (COS) monitoring, alarm notification, trend, and totalization. Airflow Dataguard controllers are microprocessors mounted on special-purpose air conditioning and refrigeration units (Airflow DATAC series). Metasys Integrator supports integration of the following DATAC systems: DATAC DX Series Dash x0 DATAC CG Series Dash x0 DATAC CW Series Dash x0 Dry Cell Series Dash x04 DATAC Mainframe Chiller Series Dash x0 DATAC DX Retrofit Series Dash x07 DATAC CW Retrofit Series Dash x08 CCT DX with Hot Gas Bypass Dash x09 TELAC Series Dash x DATAC CG Series Dash x DATAC DX Series Dash x Metasys Integrator Metasys Integrator Airflow Application

4 Metasys Integrator supports integration of the following Dataguard 4.0 systems: Tech Cool Series Dash 4x0, 4x0 CG Series Dash 4x0, 4x06 CW Series Dash 4x0, 4x07 Main Frame Chiller Series Dash 4x0 CCT DX Series Dash 4x06, 4x08 Dry Cell Series Dash 4x08 Ceiling Unit Dash 4x04, 4x0 AFX Series Dash 4x09, 4x00, 4x0, 4x04 The Airflow Dataguard series application requires a RS- to RS-4/RS-48 converter between Metasys Integrator and the Airflow Dataguard Series controllers. For this series, use either a B&B Electronics RS- to RS-4 converter (48TBLED) or an Airflow Multicontroller. For Dataguard 4.0 applications, use a Johnson Controls MM-CVT0 RS- to RS-48 converter. Each Metasys Integrator vendor port can connect to one converter or Multicontroller. Each B&B Electronics converter can connect to one Dataguard. Each Multicontroller can connect to up to Dataguard controllers. Each MM-CVT0 can connect to one Dataguard 4.0 network. Up to 0 Dataguard 4.0 controllers can be connected on a Dataguard 4.0 network. Figure shows Metasys and Airflow integration and Figure shows Metasys Companion and Airflow integration. Figure shows Metasys and Airflow Dataguard 4.0 integration. 4 Metasys Integrator Metasys Integrator Airflow Application

5 N LAN Standard NCU RS- B & B Electronics RS- to RS-4/48 Converter RS-4 Airflow Dataguard Unit UNT N Bus Metasys Integrator (-port Version) RS- Airflow Dataguard Unit Multicontroller Airflow Dataguard Unit RS-4 Airflow Dataguard Unit airflow Figure : Airflow. and Metasys Integration Panel Unit M Workstation RS- B & B Electronics RS- to RS-4/48 Converter RS-4 Airflow Dataguard Unit UNT N Bus Metasys Integrator (-port Version) RS- Airflow Dataguard Unit Multicontroller Airflow Dataguard Unit RS-4 Airflow Dataguard Unit Note: A PC version and converter may be substituted for the Panel unit. Figure : Airflow. and Metasys Companion Integration airflow Metasys Integrator Metasys Integrator Airflow Application

6 N LAN Standard NCU Metasys Integrator RS- MM-CVT0 RS- to RS-48 Converter RS-48 UNT Dataguard 4.0 Unit Up to 0 units can be connected for each Dataguard 4.0 network. Dataguard 4.0 Unit 0 N Bus Figure : Airflow Dataguard 4.0 and Metasys Integration airflow7 Component Requirements To integrate Airflow equipment, you ll need the following components: properly installed Airflow equipment RS- to RS-4/RS-48 converter (48TBLED from B&B Electronics or, for Dataguard 4.0, Johnson Controls MM-CVT0 Converter) or Airflow Multicontroller cable for connecting the converter or Multicontroller to the Airflow Dataguard. controller RS- cable (for connecting Metasys Integrator to the converter or Multicontroller) Metasys Integrator N Bus (for connecting Metasys Integrator to the Metasys or Companion Network) portable PC for downloading vendor communication tables (.VCT files) and network setup information into Metasys Integrator, and for running diagnostics cable for connecting portable PC to Metasys Integrator the correct vendor communication table (.VCT file) to download into Metasys Integrator (supplied on Metasys Integrator diskette) To integrate Airflow Dataguard 4.0 Controllers, each Airflow device must have an Airflow RS-4/RS-48 serial interface board, Airflow part number PB06. 6 Metasys Integrator Metasys Integrator Airflow Application

7 This document describes the RS- cable, the RS-4/RS-48 cable, and the vendor communication tables. Airflow documentation describes their equipment. The remaining components are described in the Metasys Integrator Technical Bulletin. Metasys Release Requirements Metasys Companion Release Requirements Vendor Component Requirements To integrate Airflow equipment into the Metasys Network, you ll need: Metasys Operator Workstation (OWS) software Release 9.0 or higher Metasys Integrator software/firmware Release 8.0 or higher To integrate Airflow equipment into the Metasys Companion Network, you ll need: Metasys Companion Release.0 or higher Metasys Integrator software/firmware Release 8.0 or higher Integration between Metasys Integrator and Airflow has been tested with the equipment listed in Table. (Table also lists the B&B Electronics converter.) Changes to this equipment or integration of Airflow products not discussed in this document will require additional software development and testing by Systems Products. For information on integrating other products, refer to the Custom Integration section of this technical bulletin. Table : Vendor Part and Version Numbers Product Part Number Firmware Version Number Airflow Product Multicontroller PB0.4 DATAC DX Series Dash x0 PB098. DATAC CG Series Dash x0 PB099. DATAC CW Series Dash x0 PB0940. Drycell Series Dash x04 PB094.0 DATAC Mainframe Chiller Series Dash x0 PB094.4 DATAC DX Retrofit Series Dash x07 PB0948. DATAC CW Retrofit Series Dash x08 PB0949. CCT DX with Hot Gas Bypass Dash x09 PB094. TELAC Series Dash x PB0946. DATAC CG Series Dash x PB09. DATAC DX Series Dash x PB096. Tech Cool Series Dash 4x0 PB00.00 Tech Cool Redundant Group Dash 4x0 PB09.00 CG Series Dash 4x0 PB006.0 CG Series Redundant Group Dash 4x06 PB00.0 Continued on next page... Metasys Integrator Metasys Integrator Airflow Application 7

8 Product (Cont.) Part Number Firmware Version Number CW Series Dash 4x0 PB CW Series Redundant Group Dash 4x07 PB0.00 Main Frame Chiller Series Dash 4x0 PB CCT Series Dash 4x06 PB00.0 CCT DX Series Redundant Group Dash 4x08 PB0.00 Drycell Series Dash 4x08 PB0.0 Ceiling Unit Dash 4x004 PB008.0 Ceiling Unit Redundant Group Dash 4x0 PB09.0 AFX Series Single Compressor Dash 4x0 PB0.00 AFX Series Single Compressor Redundant Group Dash 4x04 PB0.00 AFX Series Dual Compressor Dash 4x09 PB047.0 AFX Series Dual Compressor Redundant Group Dash 4x00 PB048.0 Airflow RS-4/48 Serial Interface Board PB06 n/a B&B Electronics RS- to RS-4/48 Converter 48TBLED n/a RS- to RS-4/48 Power Supply 48 PS n/a Johnson Controls Product RS- to RS-48 Converter MM-CVT0 n/a Vendor Contact Information Airflow Company 9 Bailes Lane Frederick, MD 70 Service and Warranty Peter Lease or Percy James Phone: (0) FAX: (0) B&B Electronics Company 707 Dayton Rd. P.O. Box 040 Ottawa, IL 60 Phone: (8) 4-00 FAX: (8) htttp:// 8 Metasys Integrator Metasys Integrator Airflow Application

9 Design Considerations When integrating Airflow equipment, consider the following: Make sure all Airflow equipment is set up and running properly before attempting to integrate with the Metasys or Companion Network. (The Airflow representative is responsible for operation of Airflow equipment.) Dataguard 4.0 controllers must have the baud rate set to 9600 (factory default is 00; the Airflow representative is responsible for setting the Airflow baud rate). For integration to a Dataguard 4.0 controller, the Airflow RS-4/RS-48 serial interface board s jumper (JP) must be set for RS-48 communications (Pins and jumpered). The Airflow representative is responsible for setting the Airflow communications type. When integrating Airflow Dataguard 4.0 Controllers to Metasys, run s accumulated on the Airflow controller must be manually reset when they reach a value close to,000,000 s. For Dataguard 4.0, an alarm reset will reset the associated alarm. For example, if there is a Return Temperature Sensor Failure alarm, BO4 - Return Air Temperature Alarm Reset - is used to reset it. If you are using the B&B Electronics converter, make sure it has the pin settings shown in Figure 4. Control should be set to SD and Echo to Off. RTS CONTROL SD ECHO ON OFF Figure 4: B&B Electronics Converter (48TBLED) Jumper Pin Settings For Dataguard 4.0, the high and low limits for the Analog Output (AO) values are correct for configuration using Degrees F only. The integration will work for hardware configured to run Celsius, but commands to the Dataguard 4.0 will be clipped by the Dataguard unit instead of by Metasys Integrator. Metasys Integrator Metasys Integrator Airflow Application 9

10 If you are using the Multicontroller, make sure its baud rate is set correctly to (The Airflow representative is responsible for operation of Multicontroller baud rate.) RS- cable distance between Metasys Integrator and the 48TBLED converter or MM-CVT0 converter can be a maximum of 0 feet. Dataguard. Controller Monitor Link Enable Dataguard. controllers with version codes of.8 or later have a configuration option added to enable or disable communications with monitoring systems. The default is DISABLED and must be changed to ENABLED to allow monitoring systems to operate with Dataguard.. The Operation and Maintenance Manual for the Dataguard. controller, included with each unit, describes the location of the option and its settings. In version codes of.46 and later, the configuration option resides in the Monitor menu. In earlier versions, it is in the Calibration section. To access the Monitor menu or the Calibration section, complete the following steps:. Press the pushbutton labeled SETUP in the upper center of the controller board to enter the Configuration mode.. Use the NEXT key to step the display to the Monitor menu or the Calibration Entry Point.. If your version does not have a Monitor menu, find the Calibration Entry Point and, while holding the SETUP pushbutton down, press the NEXT key. Failure to hold down the pushbutton will cause you to skip over the Calibration section and return to the main screen. 4. Once in the Calibration section, use the NEXT key to step through the items until the Monitor Link item is displayed (right after the LOW VOLT RESET item).. Enable Monitor Link. 0 Metasys Integrator Metasys Integrator Airflow Application

11 Cable Connections Cable Pinouts Figure shows the cable pinouts for the RS- connection between Metasys Integrator and the B&B Electronics converter or Multicontroller. Figure 6 shows the pinouts for the connection between the converter and the Airflow Dataguard controller. (Airflow documentation describes the cable between the Multicontroller and Dataguard.) Vendor Port A or B on Metasys Integrator RS- Port on Converter or Multicontroller DB-9 Female Signal Pin Pin Signal RS- DCD RD TD DTR GND DSR RTS CTS DCD RD TD DTR GND DSR RTS CTS (0 ft maximum) airflow Figure : Cable Pinouts (Metasys Integrator to Converter) B & B Electronics Converter TD (B) TD (A) RD (B) RD (A) SHLD Connector J on Dataguard. R+ R- 7 T+ 4 T- 9 GND Top View of Pinouts on Connector J on Dataguard Figure 6: Cable Pinouts (B&B Electronics Converter to Airflow Dataguard.) Metasys Integrator Metasys Integrator Airflow Application

12 Johnson Controls MM-CVT0 RS- to RS-48 Converter N+ N- Ref RS-4/48 Serial Interface Board on Dataguard 4.0 T- T+ Ref Airflow8n Figure 7: Cable Pinouts (Johnson Controls RS- to RS-48 Converter to Airflow Dataguard 4.0) Connecting the Cable Connect the female end of the RS- cable to either Vendor Port A or Vendor Port B on Metasys Integrator. Connect the other end of the cable to the RS- port on the B&B Electronics converter, the MM-CVT0 Converter, or the Multicontroller. Connect the converter or Multicontroller to the J connector on the Airflow Dataguard. Metasys Integrator 48 TBLED Converter or Multicontroller Dataguard. Controller Vendor Port A or B RS- Cable RS- Port RS-4 Cable J Connector Figure 8: Port-to-Port Connection for Dataguard. Metasys Integrator MM-CVT0 RS- to RS-48 Converter Dataguard 4.0 Controller Vendor Port A or B RS- Cable RS- Port RS-48 Cable Serial Communications Card airflow9 Figure 9: Port-to-Port Connection for Dataguard 4.0 Metasys Integrator Metasys Integrator Airflow Application

13 Metasys Integrator Setup To set up Metasys Integrator, use a portable PC connected to the Metasys Integrator Terminal Port. Metasys Integrator setup involves: downloading the correct vendor communication table (.VCT file) setting up the ports assigning network addresses to the controllers The following tables provide setup information specific to Airflow applications. Use Table if you are connecting Dataguard controllers to a B&B Electronics converter (see Table Note). Use Table if you are connecting Dataguard controllers to the Airflow Multicontroller (see Table Note). Use Table 4 if you are connecting Dataguard 4.0 controllers to the MM-CVT0 converter. For detailed procedures, see the Metasys Integrator Technical Bulletin. Table : Metasys Integrator Setup Using a B&B Electronics Converter to Dataguard. Vendor Communication Table (.VCT File) Using a B&B Electronics Converter AF_DGD.VCT, AF_DGD_H.VCT (for applications needing to set humidifier) Port Setup Baud Rate (for converter) 00 Word Length 8 Stop Bits Parity Interface Network Setup Vendor Address Timeout Value Poll Delay Performance Guide None RS-48 n/a 6000 ms ms Approximate Scan Time (for a single N address) Any Dataguard 8 seconds Note: Use AF_DGD_H.VCT if you want to set the humidifier On or Off. This table is valid only for Series: x0, x0, x0, x07, x08, x, and x. Metasys Integrator Metasys Integrator Airflow Application

14 Table : Metasys Integrator Setup Using the Multicontroller to Dataguard. Vendor Communication Table (.VCT File) Using the Multicontroller AF_DGM.VCT, AF_DGM_H.VCT (for applications needing to set humidifier) Port Setup Baud Rate (for converter) 9600 Word Length 8 Stop Bits Parity Interface Network Setup Vendor Address Timeout Value Poll Delay Performance Guide Approximate Scan Time (for a single N address) Any Dataguard None RS- Dataguard unit, Multicontroller Where: Dataguard = to Multicontroller = * example for Dataguard :, example for Dataguard :, 6000 ms ms 6 seconds * The Multicontroller, when powered up, has no address until synched by Metasys Integrator. If the address is modified, the Multicontroller must be powered down, then up, before it will accept a new address. Note: Use AF_DGM_H.VCT if you want to set the humidifier On or Off. This table is valid only for Series: x0, x0, x0, x07, x08, x, and x. 4 Metasys Integrator Metasys Integrator Airflow Application

15 Table 4: Metasys Integrator Setup Using an MM-CVT0 Converter to Dataguard 4.0 Vendor Communication Table (.VCT File) CW, CG,CCT-DX, or Tech Cool AF_DG4.VCT Controllers Dry Cell Series AF_DG4DC.VCT Main Frame Series AF_DG4MF.VCT Ceiling Unit and AFX Series AF_DG4CU.VCT Port Setup Baud Rate (for converter) 9600 Word Length 8 Stop Bits Parity Interface Network Setup None RS-48 Vendor Address Airflow Dataguard address to 0 Timeout Value Poll Delay Performance Guide Approximate Scan Time (For a single N address) Any Dataguard Initialization Time (For a single N address) Any Dataguard 000 ms ms Worst case time to report a single change of value is: 7 seconds times number of units 8 seconds times number of units Metasys Integrator Metasys Integrator Airflow Application

16 6 Metasys Integrator Metasys Integrator Airflow Application

17 Point Mapping Tables Dataguard III Commissioning Tool Labels (Generic Model) To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. This table is a generic model for the Airflow Dataguard III. Table : Dataguard III Commissioning Tool Labels (Generic Model) NPT NPA Unit Description RH Volt Volt RH Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage Channel Value Channel Value Channel Value J-4 J6-0 Temperature Setpoint Humidity Setpoint Input Temperature Temperature Setpoint Channel Value Deg C Channel Value Deg C Channel Value Deg C BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on Network Point Type Continued on next page... Metasys Integrator Metasys Integrator Airflow Application 7

18 NPT (Cont.) NPA Unit Description BO Unit Mode 0-standby, -run BO Acknowledge All Unack Alarms * 0-n/a, -ack High Channel Alarm Low Channel Alarm High Channel Alarm 4 Low Channel Alarm High Channel Alarm 6 Low Channel Alarm 7 Low Voltage 8 External Alarm (J-8) 9 External Alarm (J-7) 0 External Alarm (J-6) External Alarm 4 (J-) External Alarm (J-4) External Alarm 6 (J-) 4 External Alarm 7 (J-) External Alarm 8 (J-) 6 External Alarm 9 (J6-8) 7 External Alarm 0 (J6-9) 8 Runtime Alarm Exists Hour Hour Hour Hour Hour Hour Hour Hour Runtime (J-) Runtime (J-4) Runtime (J-) Runtime 4 (J-) Runtime (J-8) Runtime 6 (J-9) Runtime 7 (J-4) Warranty Runtime (Unit) Controller Type 0=.0, =., =. Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. 8 Metasys Integrator Metasys Integrator Airflow Application

19 DATAC DX Series Dash x0 To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Note: Binary output (BO) writes to the controller s EEPROM. Take care to limit the number of writes to this point. Table 6: DATAC DX Series Dash x0 NPT NPA Unit Description RH Volt Volt RH RH Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage Return Air Temperature Return Air Humidity Supply Air Temperature Proportional Cool Unused Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Return Air Temperature Unused Supply Air Temperature BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby, -run BO Acknowledge All Unack Alarms* 0-n/a, -ack BO Set Humidifier 0-off, -on Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application 9

20 NPT (Cont.) NPA Unit Description Network Point Type High Return Air Temperature Low Return Air Temperature High Return Air Humidity Low Return Air Humidity High Supply Air Temperature Low Supply Air Temperature Low Voltage External : Smoke Alarm External : Fire Alarm External : Water Detected External 4: Clogged Filter External : Loss of Airflow External 6: Compressor Hi Head Press External 7: Compressor Hi Head Press External 8: Compressor Hi Head Press External 9: Closed=Unack Alarm External 0: Closed=Unack Alarm Runtime Alarm Exists Runtime : Blower Runtime : Proportional Cool Runtime : Cool Runtime 4: Cool Runtime : Cool Runtime 6: Cool 4 or Heat Runtime 7: Humidifier Warranty Runtime: Unit Controller Type (0=.0, =., =.) 0 Metasys Integrator Metasys Integrator Airflow Application

21 DATAC CG Series Dash x0 To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Note: Binary output (BO) writes to the controller s EEPROM. Take care to limit the number of writes to this point. Table 7: DATAC CG Series Dash x0 NPT NPA Unit Description RH Volt Volt RH RH Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage Return Air Temperature Return Air Humidity Supply Air Temperature Proportional Cool Unused Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Return Air Temperature Unused Supply Air Temperature BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby, -run BO Acknowledge All Unack Alarms* 0-n/a, -ack BO Set Humidifier 0-off, -on Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application

22 NPT (Cont.) NPA Unit Description Network Point Type High Return Air Temperature Low Return Air Temperature High Return Air Humidity Low Return Air Humidity High Supply Air Temperature Low Supply Air Temperature Low Voltage External : Smoke/Fire Alarm External : Manual Start Prot Fault External : Water Detected External 4: Clogged Filter External : Loss of Airflow External 6: Compressor Hi Head Press External 7: Compressor Hi Head Press External 8: Humidifier Canister External 9: Closed=Unack Alarm External 0: Closed=Unack Alarm Runtime Alarm Exists Runtime : Blower Runtime : Proportional Cool Runtime : Compressor Liquid Line Runtime 4: Compressor Liquid Line Runtime : Compressor Hot Gas Bypass Runtime 6: Compressor Hot Gas Bypass Runtime 7: Humidifier Warranty Runtime: Unit Controller Type (0=.0, =., =.) Metasys Integrator Metasys Integrator Airflow Application

23 DATAC CW Series Dash x0 To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Note: Binary output (BO) writes to the controller s EEPROM. Take care to limit the number of writes to this point. Table 8: DATAC CW Series Dash x0 NPT NPA Unit Description 4 RH Volt Volt Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage RH RH Return Air Temperature Return Air Humidity Supply Air Temperature Proportional Cool Unused Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Return Air Temperature Unused Supply Air Temperature BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby,-run BO Acknowledge All Unack Alarms* 0-n/a, -ack BO Set Humidifier 0-off, -on Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application

24 NPT (Cont.) NPA Unit Description Network Point Type High Return Air Temperature Low Return Air Temperature High Return Air Humidity Low Return Air Humidity High Supply Air Temperature Low Supply Air Temperature Low Voltage External : Smoke Alarm External : Fire Alarm External : Water Detected External 4: Clogged Filter External : Loss of Airflow External 6: Humidifier Canister External 7: Pump Failure External 8: Loss of Water Flow External 9: Closed=Unack Alarm External 0: Closed=Unack Alarm Runtime Alarm Exists Runtime : Blower Runtime : Proportional Cool Runtime : Not Used Runtime 4: Not Used Runtime : Not Used Runtime 6: Heat Runtime 7: Humidifier Warranty Runtime: Unit Controller Type (0=.0, =., =.) 4 Metasys Integrator Metasys Integrator Airflow Application

25 Drycell Series Dash x04 To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Table 9: Drycell Series Dash x04 NPT NPA Unit Description 4 RH Volt Volt Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage RH Reactivation Temperature Bypass/Prop DX/Prop Proportional Bypass Damper Proportional heat/cool Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Reactivation Temperature Unused Unused BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby,-run BO Acknowledge All Unack Alarms* 0-n/a, -ack Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application

26 NPT (Cont.) NPA Unit Description Network Point Type High Reactivation Temperature Low Reactivation Temperature High Bypass/Prop Low Bypass/Prop High DX/Prop Low DX/Prop Low Voltage External : Loss Process Air Flow External : Loss Reactivation Air Flow External : Process Fan Fault External 4: Reactivation Fan Fault External : Reactivation Temp Cut Out External 6: Customer Defined Alarm External 7: Wheel Rotation Sensor External 8: Humidistat Over Setpoint External 9: Closed=Unack Alarm External 0: Closed=Unack Alarm Runtime Alarm Exists Runtime : Wheel Motor Runtime : Proportional Heat/Cool Runtime : Process Fan Runtime 4: Compressor Liquid Line Runtime : Compressor Cold Start Runtime 6: Reactivation Heater Stage Runtime 7: Reactivation Fan Warranty Runtime: Unit Controller Type (0=.0, =., =.) 6 Metasys Integrator Metasys Integrator Airflow Application

27 DATAC Mainframe Chiller Series Dash x0 To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Table 0: DATAC Mainframe Chiller Series Dash x0 NPT NPA Unit Description 4 RH Volt Volt Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage RH Return Water Temperature Supply Water Temperature Unused Proportional Cool Unused Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Return Water Temperature Supply Water Temperature Unused BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby, -run BO Acknowledge All Unack Alarms* 0-n/a, -ack Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application 7

28 NPT (Cont.) NPA Unit Description High Return Air Temperature Low Return Air Temperature High Return Air Humidity Low Return Air Humidity Unused Unused Low Voltage External : Smoke Alarm External : Pump Failure External : Water Detected External 4: Pump Failure External : Loss of Water Flow External 6: Compressor Hi Head Press External 7: Compressor Low Head Press External 8: Freeze Alarm External 9: Closed=Unack Alarm External 0: Closed=Unack Alarm Runtime Alarm Exists Runtime : Liquid Line Solenoid Runtime : Proportional Cool Runtime : Pump 4 Runtime 4: Unloader in Unloaded State Runtime : Not Used 6 Runtime 6: Not Used 7 Runtime 7: Pump 8 Warranty Runtime: Unit 9 Controller Type (0=.0, =., =.) Network Point Type 8 Metasys Integrator Metasys Integrator Airflow Application

29 DATAC DX Retrofit Series Dash x07 To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Note: Binary output (BO) writes to the controller s EEPROM. Take care to limit the number of writes to this point. Table : DATAC DX Retrofit Series Dash x07 NPT NPA Unit Description 4 RH Volt Volt Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage RH RH Return Air Temperature Return Air Humidity Supply Air Temperature Proportional Cool Unused Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Return Air Temperature Unused Supply Air Temperature BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby, -run BO Acknowledge All Unack Alarms* 0-n/a, -ack BO Set Humidifier 0-off, -on Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application 9

30 NPT (Cont.) NPA Unit Description High Return Water Temperature Low Return Water Temperature High Supply Water Humidity 4 Low Supply Water Humidity 6 7 Unused Unused Low Voltage 8 External : Smoke Alarm 9 External : Fire Alarm 0 External : Water Detected External 4: Clogged Filter External : Loss of Airflow External 6: Compressor Hi Head Press 4 External 7: Compressor Hi Head Press External 8: Compressor Hi Head Press 6 External 9: Closed=Unack Alarm 7 External 0: Closed=Unack Alarm 8 Runtime Alarm Exists Runtime : Blower Runtime : Proportional Cool Runtime : Cool Runtime 4: Cool Runtime : Cool Runtime 6: Cool 4 or Heat Runtime 7: Humidifier Warranty Runtime: Unit Controller Type (0=.0, =., =.) Network Point Type 0 Metasys Integrator Metasys Integrator Airflow Application

31 DATAC CW Retrofit Series Dash x08 To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Note: Binary output (BO) writes to the controller s EEPROM. Take care to limit the number of writes to this point. Table : DATAC CW Retrofit Series Dash x08 NPT NPA Unit Description 4 RH Volt Volt Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage RH RH Return Air Temperature Return Air Humidity Supply Air Temperature Proportional Cool Unused Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Return Air Temperature Unused Supply Air Temperature BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby, -run BO Acknowledge All Unack Alarms* 0-n/a, -ack BO Set Humidifier 0-off, -on Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application

32 NPT (Cont.) NPA Unit Description High Return Air Temperature Low Return Air Temperature High Return Air Humidity 4 Low Return Air Humidity High Supply Air Temperature 6 Low Supply Air Temperature 7 Low Voltage 8 External : Smoke Alarm 9 External : Fire Alarm 0 External : Water Detected External 4: Clogged Filter External : Loss of Airflow External 6: Humidifier Canister 4 External 7: Pump Failure External 8: Loss of Water Flow 6 External 9: Closed=Unack Alarm 7 External 0: Closed=Unack Alarm 8 Runtime Alarm Exists Runtime : Blower Runtime : Proportional Cool Runtime : Not Used Runtime 4: Not Used Runtime : Not Used Runtime 6: Heat Runtime 7: Humidifier Warranty Runtime: Unit Controller Type (0=.0, =., =.) Network Point Type Metasys Integrator Metasys Integrator Airflow Application

33 CCT DX with Hot Gas Bypass Dash x09 To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Table : CCT DX with Hot Gas Bypass Dash x09 NPT NPA Unit Description 4 RH Volt Volt Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage RH RH Return Air Temperature Return Air Humidity Supply Air Temperature Damper Proportional Cool Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Return Air Temperature Unused Supply Air Temperature BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby, -run BO Acknowledge All Unack Alarms* 0-n/a, -ack Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application

34 NPT (Cont.) NPA Unit Description High Return Air Temperature Low Return Air Temperature High Return Air Humidity 4 Low Return Air Humidity High Supply Air Temperature 6 Low Supply Air Temperature 7 Low Voltage 8 External : Smoke Alarm 9 External : Fire Alarm 0 External : Water Detected External 4: Clogged Filter External : Loss of Airflow External 6: Compressor Hi Head Press 4 External 7: Compressor Hi Head Press External 8: Customer Defined Alarm 6 External 9: Closed=Unack Alarm 7 External 0: Closed=Unack Alarm 8 Runtime Alarm Exists Runtime : Blower Runtime : Proportional Cool Runtime : Compressor Liquid Line Runtime 4: Compressor Liquid Line Runtime : Compressor Hot Gas Bypass Runtime 6: Compressor Hot Gas Bypass Runtime 7: Humidifier Warranty Runtime: Unit Controller Type (0=.0, =., =.) Network Point Type 4 Metasys Integrator Metasys Integrator Airflow Application

35 TELAC Series Dash x To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Table 4: TELAC Series Dash x NPT NPA Unit Description 4 RH Volt Volt Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage RH RH Return Air Temperature Return Air Humidity Mixed Air Temperature Proportional Damper Proportional Cool Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Return Air Temperature Unused Supply Air Temperature BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby, -run BO Acknowledge All Unack Alarms* 0-n/a, -ack Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application

36 NPT (Cont.) NPA Unit Description High Return Air Temperature Low Return Air Temperature High Return Air Humidity 4 Low Return Air Humidity High Supply Air Temperature 6 Low Supply Air Temperature 7 Low Voltage 8 External : Smoke/Fire Alarm 9 External : Fault Alarm 0 External : Water Detected External 4: Clogged Filter External : Loss of Airflow External 6: Compressor Hi Head Press 4 External 7: Compressor Hi Head Press External 8: Main Power 6 External 9: Closed=Unack Alarm 7 External 0: Closed=Unack Alarm 8 Runtime Alarm Exists Runtime : Blower Runtime : Proportional Cool Runtime : Compressor Liquid Line Runtime 4: Compressor Liquid Line Runtime : Compressor Hot Gas Bypass Runtime 6: Compressor Hot Gas Bypass Runtime 7: Humidifier Warranty Runtime: Unit Controller Type (0=.0, =., =.) Network Point Type 6 Metasys Integrator Metasys Integrator Airflow Application

37 DATAC CG Series Dash x To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Note: Binary output (BO) writes to the controller s EEPROM. Take care to limit the number of writes to this point. Table : DATAC CG Series Dash x NPT NPA Unit Description 4 RH Volt Volt Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage RH RH Return Air Temperature Return Air Humidity Supply Air Temperature Damper Proportional Cool Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Return Air Temperature Unused Supply Air Temperature BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby, -run BO Acknowledge All Unack Alarms* 0-n/a, -ack BO Set Humidifier 0-off, -on Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application 7

38 NPT (Cont.) NPA Unit Description High Return Air Temperature Low Return Air Temperature High Return Air Humidity 4 Low Return Air Humidity High Supply Air Temperature 6 Low Supply Air Temperature 7 Low Voltage 8 External : Smoke/Fire Alarm 9 External : Manual Start Protector Fault 0 External : Water Detected External 4: Clogged Filter External : Loss of Airflow External 6: Compressor Hi Head Press 4 External 7: Compressor Hi Head Press External 8: Water Flow Alarm 6 External 9: Closed=Unack Alarm 7 External 0: Closed=Unack Alarm 8 Runtime Alarm Exists Runtime : Blower Runtime : Proportional Cool Runtime : Compressor Liquid Line Runtime 4: Compressor Liquid Line Runtime : Compressor Hot Gas Bypass Runtime 6: Compressor Hot Gas Bypass Runtime 7: Humidifier Warranty Runtime: Unit Controller Type (0=.0, =., =.) Network Point Type 8 Metasys Integrator Metasys Integrator Airflow Application

39 DATAC DX Series Dash x To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Temperature Setpoint is. Note: Binary output (BO) writes to the controller s EEPROM. Take care to limit the number of writes to this point. Table 6: DATAC DX Series Dash x NPT NPA Unit Description 4 RH Volt Volt Input Temperature Input Humidity Input AC Volts Model Number (dash) AC Voltage RH RH Return Air Temperature Return Air Humidity Supply Air Temperature Proportional Cool Unused Temperature Setpoint Humidity Setpoint (40 to 60) Input Temperature Temperature Setpoint Return Air Temperature Unused Supply Air Temperature BI Any Alarm Exists BI Blower 0-off, -on BI Humidifier 0-off, -on BI 4 Dehumidifier 0-off, -on BI Free Cool 0-off, -on BI 6 Temperature Units 0-, - BI 7 Cool Stage 0-off, -on BI 8 Cool Stage 0-off, -on BI 9 Cool Stage 0-off, -on BI 0 Heat Stage 0-off, -on BI Heat Stage 0-off, -on BI Heat or Cool 4 Stage 0-off, -on BO Unit Mode 0-standby, -run BO Acknowledge All Unack Alarms* 0-n/a, -ack BO Set Humidifier 0-off, -on Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application 9

40 NPT (Cont.) NPA Unit Description Network Point Type High Return Air Temperature Low Return Air Temperature High Return Air Humidity Low Return Air Humidity High Supply Air Temperature Low Supply Air Temperature Low Voltage External : Smoke Alarm External : Fire Alarm External : Water Detected External 4: Clogged Filter External : Loss of Airflow External 6: Compressor Hi Head Press External 7: Compressor Hi Head Press External 8: Compressor Hi Head Press External 9: Closed=Unack Alarm External 0: Closed=Unack Alarm Runtime Alarm Exists Runtime : Blower Runtime : Proportional Cool Runtime : Cool Runtime 4: Cool Runtime : Cool Runtime 6: Cool 4 or Heat Runtime 7: Humidifier Warranty Runtime: Unit Controller Type (0=.0, =., =.) 40 Metasys Integrator Metasys Integrator Airflow Application

41 Tech Cool Dash Series 4x0, 4x0 Controller Points To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Chilled Water Temperature Low Alarm Setpoint is AO. Table 7: Tech Cool Series Dash 4x0, 4x0 Controller Point Mapping Table NPT NPA Unit Description 4 Deg Deg Deg Return Air Temperature Chilled Water Temperature Hot Water Temperature Return Air Humidity AO Deg Return Air Temperature High Alarm Setpoint 0-00 AO Deg Chilled Water Temperature High Alarm Setpoint 0-00 AO 4 Deg Hot Water Temperature High Alarm Setpoint 0-00 AO Humidity High Alarm Setpoint 0-00 AO 9 Deg Return Air Temperature Low Alarm Setpoint AO Deg Chilled Water Temperature Low Alarm Setpoint 0-00 AO Deg Hot Water Temperature Low Alarm Setpoint 0-00 AO Humidity Low Alarm Setpoint 0-00 AO 7 Deg Setpoint, Cooling -9 AO 8 Deg Setpoint, Heating 0-8 AO 9 Setpoint, Dehumidification 0-9 AO 0 Setpoint, Humidification 0-8 AO Proportional Cool Offset 0-0 AO Standby Unit in Redundant Group 0- Celsius Flag 0= false (), =true () Cooling Enabled 0=false, =true Heating Type 0=Electric, =Valve BI Operational Mode - Cooling 0-off, -on BI Operational Mode - Heating 0-off, -on BI Operational Mode - Dehumidifying 0-off, -on BI 4 Operational Mode - Humidifying 0-off, -on BI Unit Type 0-slave -master BI 7 Airflow Alarm BI 8 Clogged Filter Alarm BI 9 Water Detector Alarm BI 0 Low Pressure Alarm BI System Enable BI Water Flow Alarm BI 4 Firestat Alarm BI Smoke Monitor Alarm BI 6 Humidifier Alarm BI 7 High Head Pressure Alarm BI 9 Return Air Temperature High Alarm BI 0 Return Air Temperature Low Alarm Network Point Type Valid only on the master controller in a redundant group. Continued on next page... Metasys Integrator Metasys Integrator Airflow Application 4

42 NPT (Cont.) NPA Unit Description BI Chilled Water Temperature High Alarm BI 4 Chilled Water Temperature Low Alarm BI Hot Water Temperature High Alarm BI 6 Hot Water Temperature Low Alarm BI 7 Humidity High Alarm BI 8 Humidity Low Alarm BI Power Loss Alarm BI 6 Blower 0-off, -on BI 7 Heater Stage 0-off, -on BI 8 Heater Stage 0-off, -on BI 9 Humidifier 0-off, -on BI 40 Liquid Line Solenoid 0-off, -on BI 4 Compressor 0-off, -on BI 4 Hot Gas 0-off, -on BI 46 Common Alarm BI BI Return Temperature Sensor Failure Alarm Chilled Water Temperature Sensor Fail Alarm BI 0 Hot Water Temperature Sensor Failure Alarm BI Return Humidity Sensor Failure Alarm BO Unit Start/Stop 0-stop, -start BO Airflow Alarm Reset* 0-n/a, -reset BO Clogged Filter Alarm Reset* 0-n/a, -reset BO 4 Water Detector Alarm Reset* 0-n/a, -reset BO Low Pressure Alarm Reset* 0-n/a, -reset BO 8 Water Flow Alarm Reset* 0-n/a, -reset BO 9 Firestat Alarm Reset* 0-n/a, -reset BO 0 Smoke Monitor Alarm Reset* 0-n/a, -reset BO Humidifier Alarm Reset* 0-n/a, -reset BO High Head Pressure Alarm Reset* 0-n/a, -reset BO 4 Return Air Temperature Alarm Reset* 0-n/a, -reset BO 6 Chilled Water Temperature Alarm Reset* 0-n/a, -reset BO 7 Hot Water Temperature Alarm Reset* 0-n/a, -reset BO 8 Humidity Alarm Reset* 0-n/a, -reset BO Power Loss Alarm Reset* 0-n/a, -reset BO Pump Down Alarm Reset* 0-n/a, -reset Network Point Type * Do not map these points to Companion BO points. If you map these points to Metasys BO objects, make sure the Auto Restore option in the BO object s Definition and Focus window is disabled. Continued on next page... 4 Metasys Integrator Metasys Integrator Airflow Application

43 NPT (Cont.) NPA Unit Description 4 Model Number 4xxxx Version (Integer Portion) Number of Heat Stages On Master Redundant Unit State Slave Redundant Unit State Slave Redundant Unit State Slave Redundant Unit State 8 0 hrs hrs hrs Pre-Free Cool/ECWS (0-00.0) Humidifier (0-00.0) Hot Water Valve (0-00.0) Run Hours, Blower Run Hours, Humidifier Run Hours, Compressor Network Point Type Points only valid on the master controller in a redundant group. Metasys Integrator Metasys Integrator Airflow Application 4

44 CG Series Dash 4x0, 4x06 Points To get the hardware reference for mapping points to CS object attributes (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Return Air Temperature is. Table 8: CG Series Dash 4x0, 4x06 Point Mapping Table NPT NPA Unit Description Deg Deg Return Air Temperature PC/ECWS Water Temperature Return Air Humidity AO Deg Return Air Temp High Alarm Setpoint 0-00 AO Deg PC/ECWS Water Temp High Alarm Setpoint 0-00 AO 4 Deg Hot Water Temp High Alarm Setpoint 0-00 AO Return Air Humidity High Alarm Setpoint 0-00 AO 9 Deg Return Air Temp Low Alarm Setpoint AO Deg PC/ECWS Water Temp Low Alarm Setpoint 0-00 AO Deg Hot Water Temp Low Alarm Setpoint 0-00 AO Return Air Humidity Low Alarm Setpoint 0-00 AO 7 Deg Setpoint, Cooling -9 AO 8 Deg Setpoint, Heating 0-8 AO 9 Setpoint, Dehumidification 0-9 AO 0 Setpoint, Humidification 0-8 AO Proportional Cool Offset 0-0 AO Standby Unit in Redundant Group 0- Celsius Flag 0-false (), -true () Cooling Enabled 0-false -true Heating Type 0-Electric -Valve BI Operational Mode - Cooling 0-off, -on BI Operational Mode - Heating 0-off, -on BI Operational Mode - Dehumidifying 0-off, -on BI 4 Operational Mode - Humidifying 0-off, -on BI Unit Type 0-slave, -master BI 6 Compressor Pump Down Alarm BI 7 Airflow Alarm BI 8 Clogged Filter Alarm BI 9 Water Detector Alarm BI 0 Compressor Low Pressure Alarm BI System Enable BI Compressor Low Pressure Alarm BI Water Flow Alarm BI 4 Firestat Alarm BI Smoke Monitor Alarm Network Point Type Points only valid on the master controller in a redundant group. Continued on next page Metasys Integrator Metasys Integrator Airflow Application

Metasys Integrator Compu-Aire Application

Metasys Integrator Compu-Aire Application Metasys Connectivity Technical Manual 629.5 Metasys Integrator Section Application Note Issue Date 0496 APPLICATION NOTE Metasys Integrator Compu-Aire Application lntroduction Page 3 Application Details

More information

Metasys Integrator Vilter Application

Metasys Integrator Vilter Application Metasys Connectivity Technical Manual 629.5 Metasys Integrator Section Application Note Issue Date 1294 APPLICATION NOTE Metasys Integrator Vilter Application lntroduction Page 3 Application Details *3

More information

Metasys Integrator TITUS Application

Metasys Integrator TITUS Application Metasys Connectivity Technical Manual 629.5 Metasys Integrator Section Application Note Issue Date October 12, 2005 APPLICATION NOTE Metasys Integrator TITUS Application lntroduction Page 3 Application

More information

Metasys Integrator Cleaver-Brooks Application

Metasys Integrator Cleaver-Brooks Application Metasys Connectivity Technical Manual 69. Metasys Integrator Section Application Note Issue Date 0900 APPLICATION NOTE Metasys Integrator Cleaver-Brooks Application lntroduction Page Application Details

More information

Metasys Integrator Liebert Application

Metasys Integrator Liebert Application Application Note Issue Date May, 00 Metasys Integrator Liebert Application lntroduction Application Details Component Requirements 0 Vendor Contact Information Design Considerations Cable Connections Cable

More information

APOGEE Open Processor with Airflow Dataguard Driver: CCT DX Unit

APOGEE Open Processor with Airflow Dataguard Driver: CCT DX Unit Point Map Rev. 2, July, 2002 Systems Integration APOGEE Open Processor with Airflow Dataguard Driver: CCT DX Unit Table 1. CCT DX Unit, Analog Points. 01 LAI Return Air Temperature F 02 LAI Supply Air

More information

Metasys Integrator McQuay Application

Metasys Integrator McQuay Application Metasys Connectivity Technical Manual. Metasys Integrator Section Application Note Issue Date 000 APPLICATION NOTE Metasys Integrator McQuay Application Introduction Page * Application Details * Component

More information

Metasys Integrator York Application

Metasys Integrator York Application Metasys Connectivity Technical Manual. Metasys Integrator Section Application Note Issue Date 000 APPLICATION NOTE Metasys Integrator York Application lntroduction Page * Application Details * Component

More information

7.1 Data Guard 5.0 variable list

7.1 Data Guard 5.0 variable list INTERNAL ONLY Issue: DG5 Modbus Register Map Product line: Airflow with DG5 Board Environment: Airflow with DG5 Board Cause: Resolution: 7.1 Data Guard 5.0 variable list BACNET MODBU S Airflow DG5 Binary

More information

Reciprocating Chiller

Reciprocating Chiller HVAC PRO for Windows User s Manual 637.5 OEM Section Technical Bulletin Issue Date 1094 Reciprocating Chiller Reciprocating Chiller Page 3 Description 3 Theory of Operation 5 Overview 5 Control Sequence

More information

DX-9100 Applications from Engineering Services

DX-9100 Applications from Engineering Services System 9100 Technical Manual 636.4 Application Examples Section Technical Bulletin Issue Date 0896 DX-9100 Applications from Engineering Services Introduction Page 3 Overview 3 Air Handling Unit Applications

More information

NetworkAIR AFX. Operation and Maintenance AFX65 AFX18

NetworkAIR AFX. Operation and Maintenance AFX65 AFX18 NetworkAIR AFX Operation and Maintenance AFX65 AFX18 Contents Operation... 1 Display Interface.......................................... 1 Using the Display......................................... 3

More information

Data Aire DAP TM III. Metasys Control Points

Data Aire DAP TM III. Metasys Control Points Data Aire DAP TM III Metasys Control Points Data Aire, Inc. 230 West BlueRidge Avenue Orange, California 92865 Document Number 600-000-703 September 2009 Rev. 5.0 Document 600-000-703 Page 1 of 7 Table

More information

Multistate Alarm. Introduction

Multistate Alarm. Introduction Object Dictionary 1 Multistate Alarm Introduction The Multistate Alarm object adds the alarming capability for a Boolean or multistate attribute for any object, such as the Present Value of a Binary Input

More information

TC-9102 Applications

TC-9102 Applications Application Note January 7, 2004 APPLICATION NOTE TC-9102 Applications Configuring TC-9102 Applications...3 Introduction... 3 Key Concepts... 4 TC-9102 Controller... 4 Control Modes...8 Procedure Overview...

More information

READ AND SAVE THESE INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS XXXXXXX-0 EN 1904 READ AND SAVE THESE INSTRUCTIONS BASIC-PLC CONTROLLER MANUAL For all Condair desiccant dryer with equipped with Basic- PLC valid from version: PLC-35/PLC-45 18.04.03 Dehumidification

More information

UNT Applications. Using UNT Applications...3. Introduction Key Concepts UNT Controller Applications Fan Coil Units...

UNT Applications. Using UNT Applications...3. Introduction Key Concepts UNT Controller Applications Fan Coil Units... Application Note Issue Date 04/17/08 Supersedes 01/11/01 APPLICATION NOTE Using...3 Introduction... 3 Key Concepts... 4 UNT Controller Applications... 4 Fan Coil Units... 8 Unit Ventilators... 11 Rooftop

More information

Series 9. Commissioning Checklist. MISSION CRITICAL Air Conditioning Systems. ClimateWorx International Inc.

Series 9. Commissioning Checklist. MISSION CRITICAL Air Conditioning Systems. ClimateWorx International Inc. MISSION CRITICAL Air Conditioning Systems Series 9 Commissioning Checklist S9-CL2017.doc ClimateWorx International Inc. 14 Chelsea Lane, Brampton, Ontario, Canada L6T 3Y4 2 S9-CL2017.doc Commissioning

More information

MicroTech Self-Contained Air Conditioning System

MicroTech Self-Contained Air Conditioning System Open Protocol Data Information Packet Version 2.3 Group: Controls Date: October 1999 MicroTech Self-Contained Air Conditioning System Open Protocol Data Communications t 2002 McQuay International - C O

More information

Weekly Testing of Dedicated Smoke Control Dampers - Metasys System Extended Architecture

Weekly Testing of Dedicated Smoke Control Dampers - Metasys System Extended Architecture Weekly Testing of Dedicated Smoke Control Dampers - Metasys System Extended Architecture Code No. LIT-1201743 Release 1.2 Issued Date July 30, 2004 Supersedes Document Introduction.................................................

More information

Weekly Testing of Dedicated Stairwell Pressurization Fans- Metasys System Extended Architecture Code No. LIT

Weekly Testing of Dedicated Stairwell Pressurization Fans- Metasys System Extended Architecture Code No. LIT Weekly Testing of Dedicated Stairwell Pressurization Fans- Metasys System Extended Architecture Code No. LIT-1201739 Release 1.2 Issued Date July 30, 2004 Supersedes Document Introduction.................................................

More information

DAP III Zone Master User s Guide

DAP III Zone Master User s Guide DAP III Zone Master User s Guide Data Aire, Inc. 230 West BlueRidge Avenue Orange, California 92865 Document Number 600-000-788 March 2010 Revision 1.0 Document # 600-000-788 1 Overview The Data Aire DAP

More information

MicroTech Unit Ventilator

MicroTech Unit Ventilator Open Protocol Data Information Packet Version 2.2 Group: Controls Date: April 1996 MicroTech Unit Ventilator Open Protocol Data Communications 2002 McQuay International - C O N F I D E N T I A L - This

More information

P2267 NETWORK INTERFACE

P2267 NETWORK INTERFACE P2267 NETWORK INTERFACE USER MANUAL FOR OPERATING SYSTEMS: 22031-03 23636-01 October 2009 Associated Controls (Australia) Pty. Limited 2-4 Norfolk Road Greenacre, NSW, 2190. PH +61 2 9642 4922, FAX +61

More information

Introduction. What is the W2W Open controller?

Introduction. What is the W2W Open controller? W2W Open CARRIER CORPORATION 2017 A member of the United Technologies Corporation family Stock symbol UTX Catalog No. 11-808-538-01 2/8/2017 Verify that you have the most current version of this document

More information

A36D/TPSD Modbus RTU (Serial) SCADA INTERFACE INSTRUCTIONS

A36D/TPSD Modbus RTU (Serial) SCADA INTERFACE INSTRUCTIONS SCADA INTERFACE INSTRUCTIONS - OPTION 21S - FOR A36D/TPSD SYSTEMS with option 500 and 550. A36D/TPSD Modbus RTU (Serial) SCADA INTERFACE OPTION 21S INSTRUCTIONS This manual is valid for A36D/TPSD Chargers

More information

Manual Supplement. Model Number: 8680-N2. Communications Protocol. Contents of this manual supplement include:

Manual Supplement. Model Number: 8680-N2. Communications Protocol. Contents of this manual supplement include: Model Number: 8680-N2 Product/System Title: Room Pressure AOC Controller with N2 Communications Protocol Contents of this manual supplement include: 1) Sequence of Operation 2) Variable map 3) Description

More information

DX-9100/9120 Warehouse Smoke Exhaust and Reset Logic for a Rooftop Unit

DX-9100/9120 Warehouse Smoke Exhaust and Reset Logic for a Rooftop Unit Metasys Network Technical Manual 636 DX-9100/9120 Applications Section Application Note Issue Date 0497 APPLICATION NOTE DX-9100/9120 Warehouse Smoke Exhaust and Reset Logic for a Rooftop Unit Introduction

More information

USER MANUAL FOR OPERATING SYSTEM

USER MANUAL FOR OPERATING SYSTEM P2262 ALARM PANEL USER MANUAL FOR OPERATING SYSTEM 21765-07 September 1999 Associated Controls (Aust) PTY. LTD. 29 Smith Street, Hillsdale, NSW, 2036. PH (02) 9311 3255, FAX (02) 9311 3779 Page 1 of 177

More information

*IG1583EW* Aurora Touch UPC Kit Instruction Guide. Aurora Touch UPC Kit Instruction Guide

*IG1583EW* Aurora Touch UPC Kit Instruction Guide. Aurora Touch UPC Kit Instruction Guide Aurora Touch UPC Kit Instruction Guide For use in single compressor water-to-air equipment utilizing fi rmware UPCSWASTD01-01 Aurora Touch UPC Kit Instruction Guide *IG1583EW* IG1583EW 08/14 Aurora Touch

More information

Instruction Guide: Thermostat Operation

Instruction Guide: Thermostat Operation Instruction Guide: Elite Communicating Thermostats TPCM32U03*/TPCM32U04* (*GSR, GSM, TRN, AST) INSTRUCTION GUIDE: ELITE COMMUNICATING THERMOSTAT Thermostat Operation NOTE: These communicating thermostats

More information

Smart thermostat with Humidification/De-humidification control

Smart thermostat with Humidification/De-humidification control x Smart thermostat with Humidification/De-humidification control Enter/Confirm Scroll Right = Increase Left = Decrease Back/Cancel TABLE OF CONTENTS Everyday Use 1. Adjusting Temperature...3 2. Adjusting

More information

EOS INTERFACE GUIDE AND POINTS LIST For EOS BTCII Firmware Version J1239D-570 and newer

EOS INTERFACE GUIDE AND POINTS LIST For EOS BTCII Firmware Version J1239D-570 and newer Installation and interface must be performed by a qualified controls technician. IMPORTANT: THIS MANUAL CONTAINS INFORMATION REQUIRED FOR INSTALLATION, INTERFACE AND CONFIGURATION OF THIS EQUIPMENT. READ

More information

MicroTech Series-200 Flooded Screw Chiller

MicroTech Series-200 Flooded Screw Chiller Open Protocol Data Infomation Packet Version 1.0 Group: Controls Date: February 1997 MicroTech Series-200 Flooded Screw Chiller Open Protocol Data Communications 2002 McQuay International - C O N F I D

More information

Open Protocol Data Communications

Open Protocol Data Communications MicroTech Series-100 Centrifugal Chiller Open Protocol Data Communications Information Packet Version 3.2 April, 1996 - C O N F I D E N T I A L - This Document may not be copied or reproduced in any way

More information

Data Aire DAP TM III. LonWorks Protocol Integration Information

Data Aire DAP TM III. LonWorks Protocol Integration Information Data Aire DAP TM III LonWorks Protocol Integration Information Data Aire, Inc. 230 West BlueRidge Avenue Orange, California 92865 Document Number 600-000-685 Feb 2011 Revision 2.0 Table of Contents 1 Introduction...

More information

SIMPLICITY BY DESIGN M52 CONTROLLER

SIMPLICITY BY DESIGN M52 CONTROLLER SIMPLICITY BY DESIGN M52 CONTROLLER CO-WORK TM CONNECTIVITY Our controller is at the heart of all of ClimateWorx product intelligence. Co-Work TM is based on a unique multi-master network system designed

More information

MICROPROCESSOR CONTROLLER OPERATION AND MAINTENANCE MANUAL February 1, 2002

MICROPROCESSOR CONTROLLER OPERATION AND MAINTENANCE MANUAL February 1, 2002 MICROPROCESSOR CONTROLLER OPERATION AND MAINTENANCE MANUAL February 1, 2002 This manual provides information for installation, operation and preventive maintenance. The user should observe the guidelines

More information

Data Aire DAP TM III. LonWorks Protocol Integration Information

Data Aire DAP TM III. LonWorks Protocol Integration Information Data Aire DAP TM III LonWorks Protocol Integration Information Data Aire, Inc. 230 West BlueRidge Avenue Orange, California 92865 Document Number 600-000-685 June 2009 Revision 1.0 Document 600-000-685

More information

A. Base Bid: 1. Heating Contractor provide: a. Control sequences for HVAC systems, subsystems, and equipment.

A. Base Bid: 1. Heating Contractor provide: a. Control sequences for HVAC systems, subsystems, and equipment. SECTION 23 09 93 - SEQUENCE OF OPERATIONS FOR HVAC CONTROLS PART 1 - GENERAL 1 WORK INCLUDES A. Base Bid: Heating Contractor provide: Control sequences for HVAC systems, subsystems, and equipment. B. Alternate

More information

ARO Series. Description. Features. Modbus CO2 VOC. Networkable* ARO AROB24TGVH AROB24TGH. room controller. (AROB series only) or network

ARO Series. Description. Features. Modbus CO2 VOC. Networkable* ARO AROB24TGVH AROB24TGH. room controller. (AROB series only) or network ARO Series Universal Room Controller s Models ARO24T ARO24TH ARO24TGH ARO24TGVH Temp RH CO2 VOC Networkable* AROB24T AROB24TH AROB24TGH AROB24TGVH * Networkable: BACnet MS/TP or Modbus (selectable using

More information

Fan Coil Thermostat Controller Specification and Installation Instructions. Model TFHB24F3XYZ1 with External Humidity Sensor and BACnet Communication

Fan Coil Thermostat Controller Specification and Installation Instructions. Model TFHB24F3XYZ1 with External Humidity Sensor and BACnet Communication Model TFHB24F3XYZ1 with External Humidity Sensor and BACnet Communication Description The TFHB24F3XYZ1 is a fully configurable controller designed specifically for 2 pipe and 4 pipe fan coil applications.

More information

Metasys Integrator Carrier Application

Metasys Integrator Carrier Application Application Note Issue Date April 15, 2003 Metasys Integrator Carrier Application lntroduction 3 Application Details 3 Component Requirements 6 Vendor Contact Information 7 Design Considerations 7 Cable

More information

Model A1700 Series Annunciator

Model A1700 Series Annunciator Seekirk Model A1700 Series Annunciator Applications: For usage in all types of process industries, electric generation, transmission and distribution, gas and water utilities. Features: The Seekirk model

More information

Refrigeration Controller Operator s Manual (HRC) PO Box 6183 Kennewick, WA

Refrigeration Controller Operator s Manual (HRC) PO Box 6183 Kennewick, WA Refrigeration Controller Operator s Manual (HRC) PO Box 6183 Kennewick, WA 99336 www.jmcvr.com 1-509-586-9893 Table of Contents TABLE OF FIGURES...1 OVERVIEW OF THE HRC CAPABILITIES...2 INSTALLATION AND

More information

VTI MODEL itc5000 HEAT TRACING CONTROL SYSTEM OPERATIONS MANUAL

VTI MODEL itc5000 HEAT TRACING CONTROL SYSTEM OPERATIONS MANUAL VTI MODEL itc5000 HEAT TRACING CONTROL SYSTEM OPERATIONS MANUAL 1 Operations Manual for the VTI Model itc5000 Heat Tracing Control System Description The VTI Model itc5000 Heat Tracing Control System consists

More information

APC APPLICATION NOTE #119

APC APPLICATION NOTE #119 #119 InRow RP-CW and InRow RP-DX Environmental Control By Henry Jespersen Abstract The primary function of the InRow RP product is to cool air from the hot aisle and deliver it to the cold aisle at the

More information

Replaceable LED modules. Sleep or unattended mode. Auto-silence and auto-acknowledge

Replaceable LED modules. Sleep or unattended mode. Auto-silence and auto-acknowledge Replaceable LED modules 11 Alarm Sequences as per ISA-18.1 standard Each channel/window fully field programmable RS232 or RS485 MODBUS-RTU communication Repeat relay for each window and multifunction relays

More information

AIS750 Series Alarm Annunciator User Manual (Ver. 2.3 / JUNE. 2014)

AIS750 Series Alarm Annunciator User Manual (Ver. 2.3 / JUNE. 2014) AIS750 Series Alarm Annunciator User Manual (Ver 23 / JUNE 2014) 3-350 John Street, Thornhill, tario L3T 5W6 Phone: 289 597 APEX (2739) Fax: 289 597 2200 Toll Free: 1 866 776 2943 Email: mail@annunciatorca

More information

Instruction manual MTL process alarm equipment. October 2016 CSM 725B rev 2 MTL RTK 725B. Configuration Software Manual

Instruction manual MTL process alarm equipment. October 2016 CSM 725B rev 2 MTL RTK 725B. Configuration Software Manual Instruction manual MTL process alarm equipment October 2016 CSM 725B rev 2 MTL RTK 725B Configuration Software Manual SECTION 1 - INTRODUCTION... 5 Basic Requirements... 5 SECTION 2 - SOFTWARE INSTALLATION...

More information

ibox Modbus Server Gateway for the integration of Notifier ID3000 / ID3002 / ID60 / ID50 fire panels in Modbus enabled monitoring and control systems

ibox Modbus Server Gateway for the integration of Notifier ID3000 / ID3002 / ID60 / ID50 fire panels in Modbus enabled monitoring and control systems Honeywell Life Safety Iberia C/Pau Vila 15-19; 08911 Badalona Barcelona T. 902 03 05 45; Internacional:+34932424236 www.honeywelllifesafety.es infohlsiberia@honeywell.com ibox Modbus Server Gateway for

More information

FCD-wire Contents. List of Figures

FCD-wire Contents. List of Figures FCD-wire Contents FCD-X21 Configuration 1 Introduction... 1 2 Opening the FCD Application... 1 3 FCD Window... 2 4 FCD LEDs... 3 5 Configuration Operations... 4 FCD Info...4 FCD System Info...5 FCD Interface

More information

York 25-Ton VAV Rooftop Unit

York 25-Ton VAV Rooftop Unit HVAC PRO for Windows User s Manual 637.5 OEM Section Technical Bulletin Issue Date 0996 York 25-Ton VAV Rooftop Unit Introduction Page 3 Overview *3 Configuration 5 Sequence of Operation 7 Modes of Operation

More information

FieldServer Driver - Serial FS McQuay Microtech Open Protocol

FieldServer Driver - Serial FS McQuay Microtech Open Protocol Description FieldServer Driver - Serial FS-8700-80 McQuay Microtech Open Protocol This is an active client protocol. The driver is capable of acting as a master or slave. As a master, the Fieldserver polls

More information

AD-1272 Advanced Thermal Dispersion Probe Airflow Measuring System

AD-1272 Advanced Thermal Dispersion Probe Airflow Measuring System AD-1272 Advanced Thermal Dispersion Probe Airflow Measuring System Technical Bulletin AD-1272 Code No. LIT-12012477 Issued December 2017 Refer to the QuickLIT website for the most up-to-date version of

More information

Database for CTS6000 MODBUS

Database for CTS6000 MODBUS Database for CTS6000 MODBUS Valid for: LONcard SW1.7.4B, Variable List V2.02 Version 1.08-4, 01-05-2016 Contents Contents... 2 1. Installation... 3 1.1. Installation and operating instructions... 3 2.

More information

Metasys System Extended Architecture Smoke Control UL 864 UUKL Compliance

Metasys System Extended Architecture Smoke Control UL 864 UUKL Compliance Metasys System Extended Architecture Smoke Control UL 864 UUKL Compliance Checklist Code No. LIT-1201754 Release 1.2 Issued February 10, 2005 Document Introduction.................................................

More information

ExactLogic BACnet Communicating Thermostat EXL01625 Sequence Datasheet Fan Coil with Modulatating H/C and PO-PC H/C

ExactLogic BACnet Communicating Thermostat EXL01625 Sequence Datasheet Fan Coil with Modulatating H/C and PO-PC H/C ExactLogic BACnet Communicating Thermostat EXL01625 Sequence Datasheet Fan Coil with Modulatating H/C and PO-PC H/C DataSheet ev 1.10.403/4.02 November 6, 2012 Operating Sequence Standard Occupied During

More information

Marvel S MICROPROCESSOR CONTROLLER. Installation, Operation and Maintenance Manual Effective October 2018 DISCONTINUED. For Reference Only

Marvel S MICROPROCESSOR CONTROLLER. Installation, Operation and Maintenance Manual Effective October 2018 DISCONTINUED. For Reference Only Marvel S MICROPROCESSOR CONTROLLER Installation, Operation and Maintenance Manual Effective October 2018 DISCONTINUED For Reference Only ***Interactive PDF*** Contents General Purpose...3 Standard And

More information

Adaptive CyCLO Technical and HMI User Guide. CyCLO User Guide. Version th December 2017 REV

Adaptive CyCLO Technical and HMI User Guide. CyCLO User Guide. Version th December 2017 REV CyCLO User Guide Version 2.00 19 th December 2017 REV 2.00 1 Contents 1. Hardware... 3 1.1. Introduction... 3 1.2. Electrical Specification... 3 1.3. Board Overview... 4 1.4. Electrical Installation...

More information

TEC Networked Multi-Stage Economizer Thermostat

TEC Networked Multi-Stage Economizer Thermostat Installation Instructions Issue Date January 19, 2005 TEC2104-2 Networked Multi-Stage Economizer Thermostat Application The TEC2104-2 thermostat is an N2 networked thermostat that provides control of single-

More information

TEC3000 Series Field-Selectable BACnet MS/TP or N2 Networked Thermostat Controllers

TEC3000 Series Field-Selectable BACnet MS/TP or N2 Networked Thermostat Controllers TEC3000 Series Field-Selectable BACnet MS/TP or N2 Networked Thermostat Controllers Technical Bulletin Code No. LIT-12011956 Issued November 23, 2015 Refer to the QuickLIT website for the most up-to-date

More information

MicroTech Series 200 Centrifugal Chiller

MicroTech Series 200 Centrifugal Chiller Protocol Data Information Packet Version 2.2 Group: Controls Date: March 1999 MicroTech Series 200 Centrifugal Chiller Data Communications Packet for Protocol 2002 McQuay International Revision History

More information

Tempered Water Logic Control OPERATION l TROUBLE SHOOTING

Tempered Water Logic Control OPERATION l TROUBLE SHOOTING Tempered Water Logic Control OPERATION l TROUBLE SHOOTING English For MPE Multiple Chiller Units Control Panel TEMPERED WATER SYSTEMS L-2199 Rev. 20080223 Revision: L-2199 20101104 *** IMPORTANT NOTICE

More information

Table of Contents. WSHP Open v3

Table of Contents. WSHP Open v3 WSHP Open v3 Integration Guide CARRIER CORPORATION 2012 A member of the United Technologies Corporation family Stock symbol UTX Catalog No. 11-808-500-01 11/29/2012 Table of Contents Introduction... 1

More information

ModSync Sequencing System Installation & Operation Manual. For use with Fulton Steam Boilers.

ModSync Sequencing System Installation & Operation Manual. For use with Fulton Steam Boilers. ModSync Sequencing System Installation & Operation Manual For use with Fulton Steam Boilers. Revision 3.0 8/21/2008 - 2 - Table of Contents Introduction Page 4 Features Page 4 Sequence of Operation Page

More information

Installation & Maintenance

Installation & Maintenance Installation & Maintenance CM.comm Host Communications Software Table Of Contents System Overview System Features System Requirements Communications Overview CM.comm Quick Start Hardware Setup RS-232 Identification

More information

ExactLogic BACnet Communicating Thermostat EXL01627 Sequence Datasheet Fan Coil with Modulating Fan and Heat or Cool Floating Heating and Cooling

ExactLogic BACnet Communicating Thermostat EXL01627 Sequence Datasheet Fan Coil with Modulating Fan and Heat or Cool Floating Heating and Cooling ExactLogic BACnet Communicating Thermostat EXL01627 Sequence Datasheet Fan Coil with Modulating Fan and Heat or Cool Floating Heating and Cooling DataSheet ev 1.12.304/4.0 June 14, 2016 Operating Sequence

More information

NGC-UIT2 MODBUS PROTOCOL INTERFACE MAPPING FOR NGC-30 SYSTEMS. Firmware versions up to V2.0.X

NGC-UIT2 MODBUS PROTOCOL INTERFACE MAPPING FOR NGC-30 SYSTEMS. Firmware versions up to V2.0.X NGC-UIT2 MODBUS PROTOCOL INTERFACE MAPPING FOR NGC-30 SYSTEMS Firmware versions up to V2.0.X INDUSTRIAL HEAT TRACING SOLUTIONS EN-RaychemNGCUIT2Protocol-IM-H57880 06/15 1/32 Contents Section I Introduction

More information

THERMOSTATS 126. MECHANICAL THERMOSTATS 1C20 / 1C21 / 1C26 / 1E30 / 1E56 / 1F56... Wiring Diagrams / Configuration

THERMOSTATS 126. MECHANICAL THERMOSTATS 1C20 / 1C21 / 1C26 / 1E30 / 1E56 / 1F56... Wiring Diagrams / Configuration INDEX THERMOSTATS 126 l (s) Description Page(s) EMERSON BI BLUE 12" TOUCHSCREEN 1F97-1277... Wiring Diagrams / Configuration... 126 131 1F95-1280 / 1F95-1291... Wiring Diagrams / Configuration... 128 131

More information

Setup Instructions. This manual is only valid for A36D/TPSD Chargers. equipped with a 341S control card with P341S0012 or P341S0013 software

Setup Instructions. This manual is only valid for A36D/TPSD Chargers. equipped with a 341S control card with P341S0012 or P341S0013 software La Marche Manufacturing Company www.lamarchemfg.com DNP 3.0 Serial (RS232/RS485) and Ethernet (TCP/IP) SCADA Interface for A36D & TPSD Chargers with S2A-341S and S2A-383S communication cards. Option 21P,

More information

Contents. Appendix E: LonWorks Protocol Implementation Conformance Statement Document revision history... 47

Contents. Appendix E: LonWorks Protocol Implementation Conformance Statement Document revision history... 47 WSHP Open v3 CARRIER CORPORATION 2017 A member of the United Technologies Corporation family Stock symbol UTX Catalog No. 11-808-539-01 2/8/2017 Verify that you have the most current version of this document

More information

Instruction Manual Model Backup Switch, 1 for 8

Instruction Manual Model Backup Switch, 1 for 8 Instruction Manual Model 2582-282 Backup Switch, 1 for 8 December 2011, Rev. 0 MODEL 2582 SWITCH CROSS TECHNOLOGIES INC. SWITCH ALARM PSA PSB ALARM OFFLINE ONLINE UNIT STATUS 1 2 3 4 5 6 7 8 BU PROT MODE

More information

Modbus RTU RS485 Manual

Modbus RTU RS485 Manual Modbus RTU RS485 Manual AUTOMATED FUEL MAINTENANCE SYSTEMS FTI-5A, FTI-10A, FTI-20A FUEL TECHNOLOGIES INTERNATIONAL 06/10/2014 Rev B - Fuel Technologies - Modbus The Modbus Communications Setup Button

More information

OPERATION AND MAINTENANCE MANUAL

OPERATION AND MAINTENANCE MANUAL OPERATION AND MAINTENANCE MANUAL Prg Sel line alarm on on/off alarm enter Clear EMIpro MICROPROCESSOR CONTENTS 1 GENERAL CHARACTERISTICS Page 2 1.1 General description Page 2 2 EMIPRO USER INTERFACE Page

More information

EMERSON BLUE Wireless Comfor t Inter face 1F98EZ-1621 HOMEOWNER USER GUIDE

EMERSON BLUE Wireless Comfor t Inter face 1F98EZ-1621 HOMEOWNER USER GUIDE EMERSON BLUE Wireless Comfor t Inter face 1F98EZ-1621 HOMEOWNER USER GUIDE Emerson Blue Wireless Comfort Interface - Homeowner User Guide Message to Homeowners Congratulations on choosing the Emerson Blue

More information

Ethernet General Purpose

Ethernet General Purpose Ethernet General Purpose Technical Manual Revision 1.03 8 November 2013 Pakton Technologies IO PAE224 Ethernet GPIO Manual.docx Page 1 of 22 Revision 1.03 Last updated 8/11/2013 Table of Contents INTRODUCTION...3

More information

AKSolutions Data Sheet April 2007 AK882X RF POWER MONITOR. Description: Features:

AKSolutions Data Sheet April 2007 AK882X RF POWER MONITOR. Description: Features: AK882X RF POWER MONITOR Features:. > Operates from 9-30VDC power input > Installs inline to simplify mounting > Bidirectional sensor automatically detects forward and reflected power, and calculates VSWR

More information

CBI-064. User Manual. Caddx to KNX-BUS Interface

CBI-064. User Manual. Caddx to KNX-BUS Interface CBI-064 Caddx to KNX-BUS Interface User Manual GDS Intelligence in Buildings El. Venizelou 116 Nea Erithrea 14671 Tel: +30 2108071288 Email: info@gds.com.gr Web: gds.com.gr Contents 1 Device Description...

More information

Revision November 2013 JVA Technologies. Ethernet General Purpose IO Technical Manual

Revision November 2013 JVA Technologies. Ethernet General Purpose IO Technical Manual Revision 1.03 8 November 2013 JVA Technologies Ethernet General Purpose IO Technical Manual www.jva-fence.com.au Table of Contents INTRODUCTION...3 Scope and Purpose...3 Glossary...3 SPECIFICATIONS...4

More information

SECTION SEQUENCE OF OPERATIONS FOR HVAC CONTROLS

SECTION SEQUENCE OF OPERATIONS FOR HVAC CONTROLS PART 1 - GENERAL SECTION 23 09 93 SEQUENCE OF OPERATIONS FOR HVAC CONTROLS 1.1 SUMMARY A. This Section includes control sequences for HVAC systems, subsystems, and other equipment. B. See Division 23 Section

More information

Manual Supplement. Product/System Title: Static Pressure Controller. Contents of this manual supplement include:

Manual Supplement. Product/System Title: Static Pressure Controller. Contents of this manual supplement include: Model Number: Product/System Title: 8635-ST Static Pressure Controller Contents of this manual supplement include: 1) Sequence of operation 2) Description of new software items 3) Deleted software menu

More information

NGC-40 Bridge. Modbus Overview. Raychem-AR-H58862-NGC40BridgeModbusOV-EN-1805 nvent.com 1

NGC-40 Bridge. Modbus Overview. Raychem-AR-H58862-NGC40BridgeModbusOV-EN-1805 nvent.com 1 NGC-40 Bridge Overview Raychem-AR-H58862-NGC40BridgeOV-EN-1805 nvent.com 1 Table of Contents 1. NGC-40 Overview... 9 1.1 Example NGC-40 System... 10 2. Legal stuff... 11 3. Protocols... 12 3.1 Data es...

More information

725B Configuration Software Manual

725B Configuration Software Manual 725B Configuration Software Manual REV DATED DESCRIPTION AUTHOR APPROVED 0 09-03-10 First Issue P.Cartmell Page 1 of 80 SECTION 1 - SOFTWARE INSTALLATION... 5 725B ConfigurationSoftware Installation...

More information

Module Features are-configurable, no module jumpers to set

Module Features are-configurable, no module jumpers to set December 2011 PACSystems* RX3i Isolated Thermocouple Input Module, 6 Channels, IC695ALG306 Isolated Thermocouple Input Module, 12 Channels, IC695ALG312 Isolated Thermocouple Input module IC695ALG306 provides

More information

SAT- 3 Installation Setup Guide

SAT- 3 Installation Setup Guide SAT- 3 Installation Setup Guide Date: 4 February 2016 Issue: 2 Applies to: SAT- 3 room temperature controller, part number 201-000- 146 Contents 1. Quick Start Guide...2 1.1. General... 2 1.1.1. Installation

More information

HGM300/RDM800 PREVENTATIVE MAINTENANCE AND TECHNICAL SUPPORT. SECTION 1 HGM300 CPU reset, RDM800 CPU reset, WARM UP notes and HGM300 Self Test

HGM300/RDM800 PREVENTATIVE MAINTENANCE AND TECHNICAL SUPPORT. SECTION 1 HGM300 CPU reset, RDM800 CPU reset, WARM UP notes and HGM300 Self Test HGM300/RDM800 PREVENTATIVE MAINTENANCE AND TECHNICAL SUPPORT SECTION 1 HGM300 CPU reset, RDM800 CPU reset, WARM UP notes and HGM300 Self Test SECTION 2 HGM300/RDM800 Mechanical Room layout SECTION 3 HGM300

More information

Installation Guide Bacharach Communications Adapter HGM-MZ to Johnson Controls Metasys N2 Network (Electrically Isolated N2 Port Version)

Installation Guide Bacharach Communications Adapter HGM-MZ to Johnson Controls Metasys N2 Network (Electrically Isolated N2 Port Version) Installation Guide Bacharach Communications Adapter HGM-MZ to Johnson Controls Metasys N2 Network (Electrically Isolated N2 Port Version) 621 Hunt Valley Circle New Kensington, PA 15068 Tel: 724-334-5000

More information

Safety & Installation Instructions

Safety & Installation Instructions Model 8800 Universal Communicating Thermostat Safety & Installation Instructions READ AND SAVE THESE INSTRUCTIONS Table of contents Installation Installation location recommendations... 2 Thermostat mounting...

More information

The system shall be described in the following specification as manufactured by Schneider Electric

The system shall be described in the following specification as manufactured by Schneider Electric Guide Specifications Uniflair LE High Capacity Chilled Water Units THIS GUIDE SPECIFICATION IS WRITTEN IN ACCORDANCE WITH THE CONSTRUCTION SPECIFICATIONS INSTITUTE (CSI) MASTER FORMAT. THIS SECTION MUST

More information

ACCURATE ELECTRONICS INC

ACCURATE ELECTRONICS INC ACCURATE ELECTRONICS INC Page 1 of 7 Model 108078 2 Sept 09 WWW.ACCURATE.ORG PO BOX 1654 97075-1654 8687 SW Hall Blvd 97008 BEAVERTON OR USA 503.641.0118 FAX 503.646.3903 Practice Section 108078 Rev A

More information

BACnet Points List for Single Compressor Water to Water PROSSWWE-01

BACnet Points List for Single Compressor Water to Water PROSSWWE-01 The network variables will be listed by point type instance convention. 2:1 would mean point type 2, point instance 1. All volatile (Output) type points will revert to the uncommanded values after a power

More information

ENERGY LIGHT USER S GUIDE ENERGY LIGHT USER S GUIDE

ENERGY LIGHT USER S GUIDE ENERGY LIGHT USER S GUIDE ENERGY LIGHT USER S GUIDE Release January 2001 CONTENTS 1.0 GENERAL CHARACTERISTICS... 4 1.1 MAIN CHARACTERIS TICS... 4 2.0 USER INTERFACE (CODE C5121230)... 5 2.1 DISPLAY... 5 2.2 MEANING OF THE LEDS...

More information

TECHNICAL MANUAL CVM 20 C 5005 CV/04-99 GB

TECHNICAL MANUAL CVM 20 C 5005 CV/04-99 GB Summary 1 CONNECTIONS... 3 1.1 TEMPERATURE PROBES...3 1.2 LOW VOLTAGE DIGITAL INPUTS...3 1.3 LIVE DIGITAL INPUTS...4 1.4 RELAY OUTPUTS...5 2 POWER SUPPLY... 6 3 SERIAL CONNECTIONS... 6 4 SOFTWARE... 7

More information

FlameGard 5 MSIR HART

FlameGard 5 MSIR HART FlameGard 5 MSIR HART Multi-Spectral Infrared Flame Detector HART Communication with the FlameGard 5 Multi-spectral Infrared Detector The information and technical data disclosed in this document may be

More information

RF SCOUT PLUS INSTRUCTION MANUAL. Dielectric, LLC 22 Tower Rd. Raymond, ME Phone: January 2015, Rev B 1

RF SCOUT PLUS INSTRUCTION MANUAL. Dielectric, LLC 22 Tower Rd. Raymond, ME Phone: January 2015, Rev B 1 RF SCOUT PLUS INSTRUCTION MANUAL Dielectric, LLC 22 Tower Rd. Raymond, ME 04071 Phone: 800.341.9678 www.dielectric.com 21 January 2015, Rev B 1 WARNING Powering RF sensors above +30dBm (1W) will cause

More information

ACT2-CS Convenience Store Controller

ACT2-CS Convenience Store Controller Refrigeration Systems Technical Manual 804 Product Bulletins Section Product Bulletin Issue Date 0899 ACT2-CS Convenience Store Controller The ACT2-CS Convenience Store Controller is a fully programmable,

More information

icomfort Residential Communicating Control System icomfort Touch Communicating Thermostat

icomfort Residential Communicating Control System icomfort Touch Communicating Thermostat C O N T R O L S icomfort Residential Communicating Control System icomfort Touch Communicating Thermostat P R O D U C T S P E C I F I C AT I O N S Bulletin No. 210538 March 2012 Supersedes October 2011

More information

DS9400 Series. Release Notes for Firmware V2.07. Fire Alarm Control Panel

DS9400 Series. Release Notes for Firmware V2.07. Fire Alarm Control Panel DS9400 Series EN Release Notes for Firmware V2.07 Fire Alarm Control Panel DS9400 Series Release Notes for Firmware V2.07 Trademarks Trademarks Gentex is a trademark of Gentex Corporation, Fire Protection

More information

Bacnet Room Setpoint & Temp Display. Descriptions. Specifications

Bacnet Room Setpoint & Temp Display. Descriptions. Specifications Descriptions Bacnet Room Setpoint & Temp Display is designed for environment monitoring and controlling in industrial, commercial and other buildings. These transmitters can be used to monitor air temperature

More information