INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com issue No.:3 Status: Current Date of Issue: 2011-12-07 Page 1 of 5 Certificate history: Issue No. 3 (2011-12-7) Issue No. 2 (2011-7-13) Issue No. 1 (2011-2-14) Issue No. 0 (2010-9-9) Applicant: Cooper Crouse-Hinds Wolf & 7th North Street P.O. Box 4999 Syracuse, NY 13221 Electrical Apparatus: Optional accessory: NFMV Floodlight Series Type of Protection: Protection by Enclosure "td" and Restricted Breathing "nr" Marking: Ex nr II T5 Ex nr II T3 Ex td A21 IP66 T100 C Ex td A21 IP66 T200 C Approved for issue on behalf of the IECEx Certification Body: Position: Paul T. Kelly Principal Engineer, Global Hazardous Locations Signature: (for printed version) Date: 1. This certificate and schedule may only be reproduced in full. 2. This certificate is not transferable and remains the property of the issuing body. 3. The Status and authenticity of this certificate may be verified by visiting the Official IECEx Website. Certificate issued by: Underwriters Laboratories Inc (UL) 333 Pfingsten Road Northbrook IL 60062-2096
Page 2 of 5 Manufacturer: Cooper Crouse-Hinds Wolf & 7th North Street P.O. Box 4999 Syracuse, NY 13221 Manufacturing location(s): Cooper Crouse- Cooper Crouse- Hinds Hinds Korea Co, AV Javier Rojo Ltd. Gomez No 1170 106-4 Dwoong-Ri CP 09300 Dochuk-Myun Mexico City Kwangji-Si Mexico Kyunggi-Do Korea, Republic of Cooper Crouse- Hinds SA Avda Santa Eulalia 290 E-08223 Terrassa (Barcelona) Spain Cooper Electrical Australia Pty. Ltd. 205-209 Woodpark Road Smithfield NSW 2164 Australia Cooper Electronic Technologies (Shanghai) Co Ltd 955 Shen Li Road Heqing Pudong Shanghai 201201 China This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational Documents as amended. STANDARDS: The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards: IEC 60079-0 : 2004 Edition: 4.0 IEC 60079-15 : 2005-03 Edition: 3 IEC 61241-0 : 2004 Edition: 1 IEC 61241-1 : 2004 Edition: 1 Electrical apparatus for explosive gas atmospheres - Part 0: General requirements Electrical apparatus for explosive gas atmospheres Part 15: Construction, test and Marking of Type of Protection "n" electrical apparatus Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements Electrical apparatus for use in the presence of combustible dust - Part 1: Protection by enclosures "td" This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standards listed above. TEST & ASSESSMENT REPORTS: A sample(s) of the equipment listed has successfully met the examination and test requirements as recorded in Test Report: US/UL/ExTR09.0027/00 US/UL/ExTR09.0027/01 US/UL/ExTR09.0027/02 US/UL/ExTR09.0027/03 Quality Assessment Report: AU/TSA/QAR06.0020/05 GB/BAS/QAR07.0041/03 GB/BAS/QAR10.0015/01 GB/ITS/QAR10.0005/01 HU/BKI/QAR07.0001/04
Page 3 of 5 Schedule EQUIPMENT: Equipment and systems covered by this certificate are as follows: NFMV Series floodlights consists of aluminium restricted breathing enclosure with a glass cover. The glass cover is attached to the body of the floodlight by two hinges and sercured by six cover screws. A yoke mounting bracket is secured into two blind holes on teh enclosure allowing the floodlight to be mounted 30 past vertical, 60 before vertical or at 90. The yoke mount is attached to a pole mount with a SFA6 Slipfitter. The enclosure is provided with two conduit openings. Nomenclature for Type NFMV Series: NFMV M Y 400 /220 60 76 M20 I II III IV V VI VII I - Series NFMV II - Lamp/Function M - Metal Halide (M - H) S - High Pressure Sodium (HPS) III - Mounting Y - Yoke CONDITIONS OF CERTIFICATION: NO
Page 4 of 5 EQUIPMENT(continued): IV - Wattage 150-150 W (HPS only) 250-250 W 400-400 W V - Voltage /220 60-220 V, 50 Hz /230 50-230 V, 50 Hz /230 60-230 V, 60 Hz /240 50-240 V, 50 Hz /240 60-240 V, 60 Hz VI - Optical Distrubution 76 - NEMA 7X6 Beam Spread VII - Suffixes M20-20mm metric threads for conduit opening (supplied with one plug and one cable gland) M25-25mm metric threads for conduit opening (supplied with one plug and one cable gland) S714 - Furnished with lamps (lamp not installed in lampholder) S886 - Two conduit/cable glands of like thread installed S831 - Retention cable FA - Factory assembled, lamp installed in lampholder (this suffix is always last in string) Note: Standard conduit machining is two 3/4 NPT threaded entries with one cable gland and one plug installed.
Page 5 of 5 DETAILS OF CERTIFICATE CHANGES (for issues 1 and above): Issue 1: Additional manufacturing locations in Australia and China added. Issue 2: Additional manufacturing location in Spain added. Issue 3: Additional manufacturing locations in Mexico and Korea added.