Part No. 74271 Revised December 2002 DESIGNER SERIES NACHO CABINETS Instruction Manual Model #5510, 5511 AND 5512
Safety Precautions 2
FORWARD This manual covers the all models #5510, #5511 and #5512 nacho display cabinet. You can be very proud of your 5510, 5511 or 5512 Designer Series Nacho Cabinet. In addition to being an attractive "eye catcher", it contains various engineering innovations which make it the leader in the industry. The exterior of the machine is designed and built-up to present an attractive appearance for many years. INSTALLATION CHECKING SHIPMENT Unpack the shipping crate and check thoroughly for any damage which may have occurred in transit. Any claims should be filed immediately with the transportation company. ELECTRICAL REQUIREMENTS Voltage for your warmer is 120 Volt, 60 Cycle. The Holding Cabinets will draw 660 Watts. Your electrician must furnish sufficient current for the proper operation of your machine. The switches and controls which operate the display are located on the top right side of the machine. 3
OPERATING INSTRUCTIONS CONTROLS AND THEIR FUNCTIONS LIGHT SWITCH Flipping this switch to the "ON" position energizes the light. HEAT SWITCH Flipping this switch to the "ON" position energizes the heat element. Note: The is heat element is controlled by the bulb cap thermostat in the top of the cabinet. HEAT CONTROL The machine comes with a set 145 degree F bulb cap thermostat. 1. Turn light switch to on position 2. Turn heat switch to on position.. EASY STEPS FOR USING UNIT CARE AND CLEANING The aluminum body of the diaplay is easy to keep clean. Usually a damp cloth will remove all dirt and grease spots. NEVER USE ABRASIVES on the stainless steel body. The glass should always be clean and sparkling. Remember the inside of the glass must be cleaned too. 4
MAINTENANCE INSTRUCTIONS Nacho Cabinets 5
ORDERING SPARE PARTS 1. Identify the desired part by checking it against the photos, illustrations, and/or the parts list. 2. When ordering, please include part number, part name, and quantity desired. 3. Please include your model name and machine serial number (located on the machine nameplate) with your order. 4. Address all parts orders to: Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807 or, place orders at: (513) 769-7676 (800) 543-0862 Fax: (513) 769-8500 E-mail: goldme19@eos.net 6
PARTS LIST Model # Model # Model # 5510 5511 5512 Item No Part No Part No Part No Description 1 74264 74264 74264 Heat Element 600 Watt 2 38914 Heat Element 10 Watt Foil 3 42798 42798 42798 Rocker On/Off Switch 4 40721 40721 40721 Axial Fan 5 47199 47199 47199 Blower Plug and Cord 6 41020 41020 41020 Light Tube Holder 7 41021 41021 41021 Light Tube Holder W/ Starter 8 41022 41022 41022 Ballast 9 41023 41023 75026 Light Starter 10 41057 41057 39016 Light Tube 11 74216 74216 74228 Light Shield 12 38995 38995 38995 Heater Deflector 13 74211 74211 74231 Access Cover 14 74212 74212 74230 Top Plate Weldment 15 74219 74224 74226 Doors 16 74218 74218 74227 Shelf 17 74220 74220 74220 Hammer Head Screws 18 87996 87996 87996 Thermostat 149 Degree F 19 38915 38915 38915 Base Rail (Short) 74238 Base Rail (Long) 20 38916 74221 38916 Corner Post 21 38917 38917 38917 Top Rail ( Short ) 74239 Top Rail ( Long ) 22 38919 74222 38919 Verticle Door Track 23 74200 74200 Upper Door Track ( Short ) 74241 Upper Door Track ( Long ) 24 74215 74215 74215 Upper Rail ( Short ) 74240 Upper Rail ( Long ) 25 74210 74210 74242 Horizontal Door Track 26 74207 74207 74207 End Connectors 27 74217 74225 74217 Groove Filler Long 28 74270 74270 74270 Groove Filler Short 29 74201 74201 74201 Side Plate 30 74243 74243 74243 Control Side Plate 31 74244 74244 74244 Switch Plate 32 74232 Back Plate 33 74202 74202 74235 Sign Plate 34 74268 74268 74269 Sign 35 74779 77501 74779 Front and Side Glass 36 74245 Front Glass 37 74213 74213 74229 Base Plate Weldment 38 74266 74266 74266 Wrench 7
ELECTRICAL SCHEMATIC CABINET WIRING IS #18 AWG CSA LISTED, 600VOLT 105C U.L. RECOGNIZED. WIRING DIAGRAM FOR MODELS 5510 AND 5512 8
ELECTRICAL SCHEMATIC CABINET WIRING IS #18 AWG CSA LISTED, 600VOLT 105C U.L. RECOGNIZED. WIRING DIAGRAM FOR MODEL 5511 9
WARRANTY WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any defective part for a period of six (6) months from the date of sale to the Original Purchaser with regard to labor and two (2) years with regard to parts and does not cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. We neither assume, nor authorize any other person to assume for us, any other obligation or liability in connection with the sale of said GOLD MEDAL equipment or any part thereof. The term Original Purchaser as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS COMPANY, or their authorized distributor for the equipment. THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800- 543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS. NOTE: This equipment is manufactured and sold for commercial use only. GOLD MEDAL PRODUCTS COMPANY 10700 Medallion Drive Cincinnati, Ohio 45241-4807 USA 10