DELTA Switches and Outlets DELTA refle motion detector IP55 Quick and easy installation via plug-in terminals Advantages Simple mounting via plug-in terminals Automatic test mode when the rated voltage is applied for the first time Standard set values two minutes ON period and 7 lu brightness Fast set-up via two buttons Fleible implementation: wall, ceiling, or corner installation Attractive price/performance ratio Attractive design Available in colors titanium white or anthracite Supplemental functions via remote control for model 290 IR Electrical Installation from A to Z The new DELTA refle motion detector IP55 is characterized by its attractive design. It can be installed quickly and easily thanks to the plug-in terminals in the mounting base. The motion detector is adjusted automatically or via the two buttons on the device. This makes start-up quite simple. The DELTA refle motion detector IP55 is available for two different detection areas: 120 and 290. The 290 version is also available with remote control. www.siemens.com/delta
Installation with Plug-in Terminals Convenient wiring is possible thanks to installation with plug-in terminals. Installation steps: 1. Installing and wiring the connection bo The first step is to install and wire the connection bo. Afterwards, wiring can be eecuted in a simple manner. 2. Mounting the motion detector The second step is to simply plug the motion detector onto the connection bo. The three connecting pins establish the connection between the motion detector and the connecting wires. 3. Attaching the motion detector The third step is to screw the motion detector onto the connection bo. This ensures protection class IP55. Attaching with a screw makes undesired removal or theft of the motion detector more difficult. One, two, three... that s it! Three steps to install and the motion detector is ready for service. Configuration with two buttons Easy and convenient configuration and start-up of the motion detector via two buttons located behind the lens.
Remote Control With the remote control, which is included with the motion detector 290 IR, the following functions are possible. Holiday function/ Presence simulation Light 4 h ON The holiday function is a fied ON/OFF profile which simulates the presence of the inhabitants. The ON/OFF profile is activated for appro. 4 hours with the beginning of dusk. Shuts the motion detection off and switches the light for 4 hours permanently ON. OFF function Light is permanently OFF, motion detection is deactivated. Test function Activation of the test function for 10 minutes (brightness-independent, 1 second ON and 2 seconds OFF). Standard mode By pressing this button, the operating modes of the blue buttons are quit and the formerly set operating mode is activated once again. Save brightness-/ dusk-settings With this function, the already set brightness factor is replaced with the currently detected brightness factor. Brightnessindependent day mode The motion detector is also activated during day time independent from brightness. Set overrun time (start and stop time recording) With this button, the individual overrun time, ranging between 5 seconds to 30 minutes, can be programmed. Overrun time 10 min. Impulse function This function can be chosen when the motion detector is used with individual settings (standard operating mode) or in brightness-independent mode (day mode). The currently set delay time will be replaced. Impulse mode for 1 second ON, 9 seconds OFF. Options for use e.g. for staircase time switches, doorbells. Programming button For the programming of the yellow-button functions it is always necessary to press the programming button. Reset button The reset function can be used while in any operating mode (also in OFF function) and switches the motion detector back to factory settings (7 Lu / ON period 2 min.).
Technical Data DELTA refle motion detectors IP55 Variants DELTA refle motion detector 120 DELTA refle motion detector 290 DELTA refle motion detector 290 IR MLFB titanium white (similar to RAL 9010) 5TC7 210 5TC7 212 5TC7 214 anthracite 5TC7 211 5TC7 213 5TC7 215 Incl. remote control Technical data Protection class IP55 IP55 IP55 Detection area 120 290 290 Connected load 1000 W 5AX 2500 W 10AX 2500 W 10AX Load Bulbs 1000 W 2500 W 2500 W HV halogen bulbs 1000 W 2500 W 2500 W Fluorescent tubes 8 58 W 20 58 W 20 58 W Energy-saving bulbs ma. 4 ma. 8 ma. 8 Terminals for rigid conductors 1 mm² 4 mm², ma. 2 2.5 mm² fleible conductors 1 mm² 2.5 mm², ma. 1 2.5 mm² Range at 22 C 10 m 16 m 16 m Mounting height 2 4 m 2 4 m 2 4 m Wall or ceiling mounting Surface mount model with plug-in terminals, detector is simply plugged onto the connection bo after convenient wiring Mounting with special base Features Rear field detection Control via opener button Light ON (delay time), Continuous ON (4 h), Light OFF (back to normal mode) here only light ON (delay time) possible Pulse mode (1 s ON, 9 s OFF) Ambient light suppression (glare protection 60 s) Switching error suppression Range stabilization Presence simulation/vacation function After twilight 4 h permanently programmed ON/OFF profile in 24 h rhythm Wall and ceiling mounting Remote control Generous wiring area Numerous cable entries Convenient installation by plugging the detector onto the mounting base Convenient detector adjustment via 2 button operation Automatic set-up adjustment the first time voltage is applied Convenient two-button operation: Saves desired brightness value Saves desired delay time between 5 s and 30 min Changes to brightness-independent mode and pulse mode Reset values 7 lu and 2 min ON period Test mode to check the monitoring range
Installation There are three different ways to install the motion detector: Wall installation Ceiling installation Inside corner installation and outside corner installation Adjusting and reducing the detection area The detection area can be changed by turning the lens to the left or right + / 30. The detection range can be changed by adjusting the swivel arm. The motion detector has a cover blind that can be used to limit the detection area. It is necessary to cut out the cover blind accordingly to do this. Adjust the detection area by cutting out the cover blind
DELTA Switches and Outlets Product Order No. PU (unit) DELTA refle motion detector IP55 120 titanium white 5TC7 210 1 120 anthracite 5TC7 211 1 290 titanium white 5TC7 212 1 290 anthracite 5TC7 213 1 290 IR titanium white 5TC7 214 1 290 IR anthracite 5TC7 215 1 DELTA refle special base, for IP55 motion detector titanium white 5TC7 900 1 anthracite 5TC7 901 1 DELTA refle remote control, for IP55 motion detector 5TC7 902 1 The desired features are only binding if they have been epressly agreed when a contract is concluded. All product designations can be trademarks or products of Siemens AG or other supplier companies, the use of which by third parties for their own purposes can violate the rights of the owners. This product information contains only general descriptions or features that may not always apply in the specific application case in the form described, or that can change due to further development of the products. See catalog ET D1 for accessories and technical details. Siemens AG Automation and Drives Electrical Installation Technology P.O. Bo 10 09 53 93009 REGENSBURG GERMANY www.siemens.com/delta Siemens AG 2006 E20001-A5760-P440-X-7600 Update: http://www.siemens.com/delta Information subject to change without notice