NO. 6, 6, 690, 697 SIOUX AIR RANDOM ORBITAL SANDER INCLUDES B, V, VV, & X SUFFIXES (SERIAL E ) Form Z262A Date 9-99/B Page of CAUTION Do not at any time attempt to operate this tool without shroud and pad in place. OPERATION The sander is designed to operate on 90 p.s.i. air pressure. An air regulator is recommended if pressures are higher than 90 p.s.i. A filter is strongly recommended to provide clean air for long life of the sander. Lubricate the sander by adding 8-0 drops of air motor oil into the air inlet each day before using. HOSE AND HOSE CONNECTIONS Hoses should not be smaller than /8" I.D. with /" pipe thread fittings. LUBRICATION As mentioned above, 8-0 drops of Sioux air motor oil, Cat. No. 288, should be added to the air intake before using each day. This will help protect the motor parts from rusting due to water in the air lines and also lubricate the parts for longer life. Caution should be taken not to add too much oil as it will blow through the tool and may get on the surface being sanded. An air line oiler will increase the life of the tool. The setting should be about drop of oil per -2 minutes of use. SPEED CONTROL AND SHUT OFF COUNTERWEIGHT A speed control and air shut off is located on the bottom of the housing. This control is adjusted as shown in the diagram. This is to control the speed of the MAXIMUM SPEED tool for various sanding operations and to control excessive air pressure. The control is also used to shut off the air to the tool to safely change sand paper on the pad. COUNTER BALANCE The units are equipped with different counterweights to decrease the vibration. Following is a chart of pad size and counterweight. APPROX. PAD SIZE PAD WEIGHT COUNTER WEIGHT 5" 90-00 Grams 6 W/Lockout 6" 5-25 Grams 68 W/Lockout 5" 90-00 Grams 60 WO/Lockout 6" 5-25 Grams 67 WO/Lockout OFF LOSS OF POWER & SPEED The air motor is probably dirty and sticky. Flush out by adding very light weight oil to the air intake and run unit. Do this several times until it runs properly. Then add 8-0 drops of Sioux air motor oil, Cat. No. 288, in the air intake and run tool to lubricate. WARNING Continued exposure to vibration may cause injury to your hands or arms. Printed In U.S.A.
2 2 6 62 6 65 6 9 0 2 27 28 29 0 2 5 6 7 8 9 0 2 5 6 7 8 9 50 6 7 8 9 20 2 22 2 2 25 26 57 57 56 55 5 5 52 5 5 6 7 8 5 5 55 56 6 62
NO. 6, 6, 690, 697 SIOUX AIR RANDOM ORBITAL SANDER INCLUDES B, V, VV, & X SUFFIXES (SERIAL E ) No. No. Description. 669 Housing [Also Includes (2*) Fig. 2, (*) Fig. 6 & (*) Fig. 52] 2. 06205 Screw Fillister Hd. #6-2 x 5/6 Taptite (2)*. 56 Lever Valve (Palm Grip). 50 Pin 5. 2 Lever Valve 6. 6 Sleeve 7. 5 Cover 8. 07225 Screw Phil. Pan Hd. #0-2 x /8 9. 6575 Stem Valve (6, 6 Units) 6667 Stem Valve (690, 697 Units) 0. 65289 Ring O. 22 Spring 2. 62 Control Output. 2 Ring O (/6 x 7/6 x 9/6). 8 Washer Wave 5. 25680 Washer 6. 2826 Ring Retaining 7. 56 Lever Output Control 8. 6 Washer Belleville 9. 06672 Screw Phil. Rd. Hd. #8-2 x /" 20. 255 Ring Retaining 2. 0 Bearing Ball 22. 622 Plate Upper End 2. 625 Cylinder 2. 7 Vane Rotor (Set of ) 25. 622 Rotor 26. 000 Key Woodruff 27. 65572 Plate Lower End 28. 6557 Bearing Ball 29. 6576 Spindle Rotor 0. 0005 Bearing Needle. 60 Counterweight (WO/Lockout)(5" Pad) 67 Counterweight (WO/Lockout)(6" Pad) 2. 07097 Screw Button Hd. Soc. #0-2 x /2. 275 Ring Retaining. 6650 Bearing Ball (All units except V & VV) 0228 Bearing Ball (All V & VV units) No. No. Description 5. 6 Spindle Pad 6. 25 Ring Retaining 7. 6 Counterweight (W/Lockout)(5" Pad) 68 Counterweight (W/Lockout)(6" Pad) 8. 222 Spring 9. 00 Ball Steel (/8" Dia.) 0. 5 Ring Lock. 66 Knob 2. 0726 Screw Flat Hd. Cap #0-2 x 5/8. 0508 Gasket (2 required on V units). 66250 Shroud Rubber 5. 66 Retainer 6. 678 Screw Pan Hd. #0-2 x 5/8 (Taptite)()* 7. 695 5" PSA Tapered Edge Pad 696 6" PSA Tapered Edge Pad 8. 6 Retainer Motor 9. 0056 Shroud Vacuum 50. 7 Retainer Motor 5. 52 Washer ()* 52. 0725 Screw Pan Hd. #0-2 x (Taptite)()* 5. 5V 5" Backing Pad, Vacuum Type 5. V 6" Backing Pad, Vacuum Type 5. 629 Housing Muffler 55. 0509 Pad Silencer 56. 028 Spacer 57. 6 Adapter Intake. 09 Ring O (/6 x /2 x 5/8). 06 Screen. 25 Ring Retainer 6. 656 Ass y Exhaust Tube 62. 76 Ass y Air Hose 6. 60 Handle 6. 62 Adapter Intake (Long) 65. 67 Adapter Intake (Remote Exhaust) Not Shown: 05 Wrench 5/8 *Order Quantity As Required FURNISH CATALOG, SERIAL, AND MODEL NUMBER WHEN ORDERING PARTS
NO. 690VV, 697VV (SERIAL D ) 5 6 2 5 7 6 8 7 8 9 No.. No. 5V Description Vacuum Pad 5" V Vacuum Pad 6" 2. 0728 Screw Pan Head #0-2 X / (Taptite)()*. 66 Retainer Motor. 657 Shroud Flexible 5. Ring O (/6 X X -/8) 6. 6572 Extractor 7. 28 Ring O (/6 X 5/8 X /) 8. 25206 Washer 9. 09 Ring O (/6 X /2 X 5/8) 0. 6 Adaptor Intake (Includes Fig s. 2, & 5). 06 Screen 2. 25 Ring Retaining. 85 Hose Dust Collection. 9A Ass y Disposable Dust Bag (Includes Fig s., 5, 7, & [ Only] Fig. 6) 65768 Bag Outer 5. 65770 Washer 6. 92 Bag Filter (Quantity of 5) 7. 6577 Clip 8. 2799 Ring Retaining ** 65505 Cable Ties (Set of ) (Not Shown) 0 Note: To ensure maximum dust pick-up, periodic cleaning of extractor & filter bag replacement is required. 2 ** Cable ties used to secure supply hose to vacuum hose if desired. *Order Quantity As Required Printed In U.S.A.
This pdf incorporates the following model numbers: 6, 6, 690, 697