Robot Vacuum Cleaner Edge Cleaning Side Brushes Cliff Sensor, Cordless and Lightweight Includes Additional Accessories tiffany
2 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Batteries not included. Remote control - 2 x AAA size battery required. Virtual Wall - 2 x D size battery required per wall. 2.
5240 Robot Congratulations on the purchase of your new HOOVER vacuum cleaner. There are many useful features built into your vacuum cleaner and we recommend that you carefully read this instruction manual so that you may take best advantage of them. Features: 1. Infrared Sensor 2. Battery Life Indicator (Light on = Power on) 3. Easy Grab Handle 4. Operating Buttons 5. Side Brush 6. Removable Dust Bin 7. Battery Charger Socket 8. Power Switch 9. Virtual Wall Unit x 2 10. Mains Power Adaptor 11. Rechargeable Battery Pack (Installed) 12. Charging Base Plate 13. Spoon 14. HEPA Filter 15. Remote Controller 16. Cleaning Brush Specifications: Voltage: 14.4V Input of charging base: 24V 1A Please contact Hoover Customer Care 1300 360 845, NZ (09) 263 7573 to find your local spare parts provider. 3.Features
Robot Vacuum Infrared sensor Easy to grab handle Battery life indicator Operating buttons Rechargeable battery (not shown) Sensors Removable dust bin Sensors Main brush Side brush HEPA filter Vacuum inlet lid Power switch Battery charger socket 4.
Virtual Wall unit Power indicator Power switch Range selector switch Infrared wave emitter 0-5m 0-3m 0-1.5m The Virtual Wall Unit has three setting options to choose from depending on the size of the room. CAUTION! Do not use the infrared wave emitter to point at the eyes! Charging Station Signal sensor LCD display Function setting keys Charging base plate 5.Features
Before you Begin This cleaner must be operated in accordance with these instructions and used only for domestic household cleaning to remove DRY dirt and dust from household carpets, flooring, walls and fabrics. This cleaner is not fit to be used as an industrial cleaner hence will void the manufacturer s warranty if used inappropriately. Please read these instructions thoroughly This will ensure you obtain full benefit from your new cleaner. Keep this Instruction Manual in a handy place for future reference. Important Always switch the cleaner off and remove the plug from the electricity supply before cleaning your appliance, when not in use, or attempting any maintenance task. The cleaner must only be connected to an AC supply at the voltage shown on the rating plate. This cleaner should only be used for its intended purpose as described in these instructions. Precautionary measures: 1. Do not operate the vacuum cleaner too close to heaters, radiators, and other hot surfaces. 2. Before inserting the plug into the wall, make sure your hand is dry. 3. Before turning on the vacuum cleaner, remove any large or sharp objects from the floor or cleaning surface in order to prevent damage to the filter. 4. When you want to pull the plug from the wall, do not use the power cable, gently pull the plug from the power socket. 5. Do not use vacuum cleaner to pick up water or liquids. 6.
Safety Precautions & Warnings WARNING: Electricity can be extremely dangerous. This appliance is powered by rechargeable Ni-MH batteries and is provided with a charging base plate. Please ensure the voltage marked on the mains power adaptor is suitable for connection to standard mains power outlet voltage. REMINDERS: 1. Always store the appliance indoors. Do not use outdoors or expose the appliance to the elements, humidity or heating sources (oven, fireplace, wet floor). 2. Do not expose the Robot or accessories to excessive heat/cold (Keep between 0-30 C). 3. Do not drop the Robot or use any accessory if it has been dropped, damaged, left outdoors or dropped in water. 4. Never unplug or pull the mains power adaptor by the power cord. 5. Never pick up matches, hot ash, cigarette ends, or sharp objects. 6. Do not spray with, or pick up flammable liquids, cleaning fluids, aerosols, or their vapours, as this may increase the risk of fire/explosion. 7. Do not continue to use your Robot if it appears to be faulty. If the mains power adaptor power cord is damaged, stop using it IMMEDIATELY: to avoid a safety hazard, only an authorised Godfrey s Service technician must replace the Power Cord. 8. This Robot is for use on wooden flooring, rubber, ceramic tile, linoleum and short pile carpet. 9. Do not use to clean stairs. After Use: Return the Robot to the Charger Base Station. Always switch off and disconnect the mains power adaptor before cleaning or attempting any maintenance task. If the Robot will not be used for a long time (several weeks), unplug the Charger Base Station according to the instructions in this User Manual. Safety with children, the elderly or infirm: This cleaner is not a toy. Do not let children play with the appliance or its controls. Please supervise the use of the appliance by older children, the elderly or the infirm. 7.Before you Begin
Safety Precautions & Warnings No one else can disassemble, maintain or transform the product except the maintenance technicians designated by our company, or it may cause fire, electric shock or personal injury. Don t touch high-voltage power cable of the electric appliance with your hands or it may cause electric shock. Don t twist clothes or any part of the body (head, finger, etc.) into the brush or wheel of the Robot, or it may cause personal injury. Don t use other chargers only the one supplied with the unit or it may cause product damage, electric shock or fire due to high voltage. CAUTION Don t bend the power cable overly or place weight on it, or it may cause power cable damage, fire or electric shock. Don t approach cigarette, lighter, match and other heat objects or combustible materials such as the gasoline cleaner. Don t forget to turn off the power while transporting or storing the cleaner for long or the battery may be damaged. Check that the charger and socket are connected well, or it may cause charging failure or even fire. Insert the power cable of the charger well or it may cause electric shock, short circuit, smoking or fire. Remove all easily damaged objects (including luminous objects, fabrics, glass bottles, etc.) before using, or it may cause damage to these objects or affect the use of the cleaner. Don t stand or sit on the cleaner, or it may cause damage to the cleaner or personal injury. ATTENTION Please use the cleaner cautiously in the presence of children to avoid frightening or harming them. Don t allow the cleaner to suck up any water or other liquids to avoid damage to the product and harm to yourself. Don t use the cleaner outdoors, or it may cause damage to the product. v Don t use the cleaner on small tables and chairs or other small spaces, otherwise the cleaner may be damaged. Don t use the cleaner in commercial places, or the cleaner may be damaged by excessive use. Don t leave movable threads, wire and other objects with the length of more than 150mm on the ground or the brush may be entangled. The cleaner is not for use by the disabled (people with physical or mental handicap) or children. Users of the cleaner should read the manual before operating the unit. 8.
Assembly WARNING! The cleaner should be switched off and disconnected from the mains power supply before assembling. Outlet Setting the Auto Charging Base Plate Battery charger socket Battery charger socket Outlet Wall fixing plate 1. The cleaner may be charged directly by the charger as well as by the auto charging base plate. If the battery is about to run out, the indicator will turn blue and the cleaner will automatically stop cleaning and seek the charging base plate for charging when machine is set under turbo and timing mode. 9.Safety Precautions & Warnings
Assembly (continued) 2. For charging with auto charging base plate, the plug of charger should be inserted into the DC socket at the back of the base plate, meanwhile, the screen on the base plate will display the time, etc. 3. The charging base plate must be correctly installed and be placed on the floor with the back on the wall and no object under it. The base plate may be fixed on the wall by the soft glue on the wall fixing plate space. (Remove the paper from the wall fixing plate and fix the charging base plate on the wall with the adhesive). 4. In order to prolong the life of the battery, it should be charged for 8-9 hours for the first use or when being used again after a long time. It can only reach its best performance after 2-3 cycles of charging and discharging. 5. While charging, the charging light (on top of the unit) will flash indicating that the battery is being charged, once fully charged, the charging light will remain on. 6. If the room is too large and the cleaner cannot find the charging base plate immediately, you may manually return it to the base plate. Place the cleaner 1.5m away from the base plate, and then press the power switch and Turbo Clean key. Alternatively, return the cleaner near to the base plate and it will automatically find it and begin to charge. 10.
1 Clock Timing Clock key Timing key a. Press the clock key to adjust the time of clock as shown. b. Press the clock key three times and respectively adjust hour, minute and week. Press +/- key to adjust the specific parameters. After setting the time, press the clock key and the clock setting is ok. At this time, there is 1 before the time displayed in the screen. Timing Clean Function 2 Clock Timing Clock key Timing key Press the timing key to set the alarm time, and the cleaner will automatically work as per the set specified time with the specific operating methods: a. Press timing key to set the hour. It can be adjusted by the key +/-. b. Press timing key again to set the minutes. It can be adjusted by the key +/-. c. Press timing key three times and the screen will display OFF. At such time, the alarm function is off. If you want to turn on the alarm, you may press + key, the screen will display ON and then press the timing key again. d. After it displays ON for alarm setting, there will be 2 displayed before the time in the screen. CAUTION! The time intervals between the pre-set time set by the timing key and the standard time set by the clock key is above 4.5 hours. The timing cleaning function will be affected merely when the battery is fully charged for 4.5 hours. Assembly 11.
Assembly (continued) Auto Cleaning Function a. The cleaner will automatically work after being fully charged. Full go key Clock key Clock Timing Timing key b. Press the full go key there will be a broom icon displayed at lower right corner of the screen, which means the function is on. Press the key again; the broom icon will disappear, which means the function is off. c. There is a charging dynamic image flashing on the screen when the cleaner is charging on the auto charging base plate. Meanwhile, the battery indicator will flash. If it turns green, it means it has been fully charged and is able to work. Generally, the charging time is 4-6 hours. Infrared Remote Control Power key Spot clean key Auto clean key Indicator Turbo clean key The cleaner can be controlled manually using the infrared remote control. The three setting keys are the same as the ones that are on the unit. The direction keys can operate the cleaner to work in different directions. SPOT CLEAN LEFT AUTO CLEAN FORWARD TURBO CLEAN RIGHT Direction keys a. The P key is for powering on/off. Press the P key, the indicator on the panel will turn off and the cleaner enters sleep mode, which enables the unit to save energy when not in use. BACK b. Press the P key again, the indicator will turn on, and the unit will enter the standby stage, waiting for the next command. c. When the virtual wall and remote control are used in the same area, as they all use the infrared signal, this may lead to temporary failure of the remote control, you may operate the remote control after turning off the virtual wall or when the unit is far away from the Virtual Wall. 12.
Instructions for Use It s better to put the Virtual Wall Unit behind the door. Infrared ray 1. Please ensure the battery is fully charged before starting the cleaner. 2. Please ensure any unfixed articles are removed from the floor space before using the cleaner, and ensure that there are no spikes on the edges of the carpet or power cables lying on the floor. 3. Turn on its main power start button, there are three start buttons: Spot, Auto and Turbo, representing three different cleaning modes. In addition, there is a timing work mode: a. Spot mode (S): The cleaner can make repeated screw type cleaning within the scope of 3 feet of diameter, focusing to clean a spot for 4 minutes. This mode is applicable for cleaning a room that is dirty in some places. b. Auto mode (M): The cleaner will automatically clean the room for 30 minutes. This mode is applicable for cleaning small rooms. c. Turbo mode (L): The cleaner won t stop running until complete consumption of its power. The working time is excess 75 minutes. If the auto charging base plate is used, the cleaner will automatically return to it for charging. d. Timing mode: The cleaning time can be set by the time setting key on the charging base plate. The cleaner will leave the auto charging base plate to work as per the pre-set time and the cleaning time is 75 minutes, and then it will automatically return to the socket for charging. Assembly 13.
Instructions for Use (continued) 4. If you don t want your cleaner to clean those areas beyond your desired cleaning area, please place the Virtual Wall Unit at the proper place. 5. When the wrong start button is pressed, the other start switch needs to be pressed twice before cleaning. 6. The maximum working time for the cleaner is about 75 minutes, which can meet the requirements for cleaning a normal room. If the battery power is about to run out, the battery life indicator will become blue, and it will stop working. Intelligent Path Judgment The Intelligent Robotic Vacuum is self controlled and can avoid any obstruction. It will also change direction before falling down steps. TABLE CAUTION! Ensure all small objects such as vases, small paper boxes etc are removed from cleaning area. These can be knocked down during cleaning. 14.
Helpful Hints 1. For the purpose of ensuring the cleaner is automatically charged, regularly wipe the charging contact at the front of the unit and the charging dome on the base plate with a dry cloth, so as to keep it free of dust, otherwise it may result in poor contact. 2. The charging base plate should be installed in as open place as possible, and do not place any obstacle within the range of 1.5m of the charging base plate, this will affect auto charging. 3. The Cleaner should be matched with the attached charger. Do not use any other charger and battery to avoid damage to the unit. 4. In order to prolong the life of the battery, it should be charged for 8-9 hours for the first use or when being used again after a long time. It only can reach its best performance after 2-3 cycles of charging and discharging. 5. If the cleaner is switched on but stops after the short music playing, this may mean the battery is low or off and charging is required. 6. Do not use the cleaner on high-pile carpets. 7. Avoid using the cleaner where there are objects such as clothing, power cables, towels,etc. As these things may entangle the brushes of the cleaner. 8. It is good to turn off the power switch after use and must be fully charged if it s not used for a long time. Take the battery out of the unit and store the battery and unit in a cool, dry place when not in use. Instructions for Use 15.
Maintenance (continued) IMPORTANT! Ensure the vacuum cleaner is not connected to the power supply when performing any maintenance procedures. Use a damp cloth and mild detergent when cleaning the appliance. Emptying the Dust Bin 1. Turn off the power switch. 2. Press down the bin clip and pull out the dustbin. 3. Empty the dustbin. 4. When inserting the dustbin, press the clip on the bin to facilitate return. Cleaning the HEPA Filter 1. Turn the dustbin upside down. 2. Press the bottom slightly, remove the HEPA filter gently. 3. Clear the dirt on the HEPA filter mesh. 4. Fit the HEPA filer back to the dustbin. Press the clip slightly and put the dustbin back into the cleaner. 16.
Cleaning the Main Brushes of the Cleaner 1. Turn off the power switch and put the cleaner on a flat surface upside down. 2. Using right thumb, push forward the locking rod and lift up the cover; using left hand, hold the middle hairbrush and lift up. 3. Clean the chamber where the brush is located and the contaminants on the brushes. 4. Wipe out dirt on the metal shaft and bearing of the brush coupler and the brushes (this may not be necessary to do after every use). If necessary, you may add a little lubricant to it. 5. Put the brush coupler and brushes back and tighten the screw. Maintenance 17.
Maintenance (continued) Cleaning the Vacuum Inlet Lid 1. Turn off the power switch; turn the cleaner upside down on flat surface. 2. Remove the vacuum inlet lid out as per following drawing. 3. Clean the vacuum inlet lid and the fan-shaped mechanism to ensure good ventilation. 4. Guide the hinge tabs on the vacuum inlet lid back into their holes carefully. CAUTION! Please open the vacuum cover as shown: 1. Pressing the board as No.1; 2. Pushing the buckle slightly as No.2; 3. Rotate it up as No.3. 3 2 1 Replacing the Side Brush The side brush is a consumable and will wear out over time. 1. Screw out the two screws. 2. Turn the side brush to the extent that the screwdriver can be inserted, loosen the screen, take off the old brush and replace with a new one. 3. Install the side brush and bottom housing in adverse order. 18.
Troubleshooting Problems and Solutions If you come across a problem, please use the checklist of troubleshooting tips before ringing Hoover Customer Care. Problem Cleaner is falling down stairs (ie: not changing direction when stairs are sensed). Cleaner stops running and all indicators are on during cleaning. Cleaner is rotating in the one position abnormally. The virtual wall doesn t work. The battery will not charge. Cleaner can not find the charging base plate. Cleaner does not perform timing cleaning function. Solution Wipe away the dust for the probe at the bottom of the front plate with a dry cloth. Ensure there are no large objects blocking the main brush or the wheels and clean the dust bin if full. Ensure there are no large objects blocking the main brush or the wheels and clean the dust bin if full. Place the virtual wall unit in the right place. Replace the battery for the virtual wall if the green indicator keeps flashing. Check whether the battery is correctly installed and you should hear two sounds when installing the battery. Then check whether the contact on the front plate and dome on the base plate is dirty. If it can t be charged on the base plate directly use the charger for the unit to charge. The wrong mode has been selected, the robot can only find the charging base plate under turbo and timing mode. The base plate will produce an infrared signal and it only returns to the base plate after finding the signal. You should confirm the power is on for the base plate and do not use the virtual wall near the base plate as its signal may affect the robot s ability to find the position of the base plate. If the room is large, it is possible that the cleaner won t find the base plate after cleaning. In such circumstances, you should replace the base plate and do not put any obstacles within 3-4m around it. Check whether there is power failure for the charging base plate or while in operation. If the displayed parameters change, it should re-set them again. Maintenance 19.
tiffany Robot Vacuum Cleaner Conditions of warranty Your Hoover cleaner, in the case of domestic use, has a one year parts and labour warranty against product defects and failures when the product is used in accordance with the terms and conditions of this warranty statement. This warranty commences from the original date of purchase and is not transferable; please retain your original proof of purchase for any warranty claims. This warranty is valid only in the country where the cleaner is purchased. The cleaner must be operated in accordance with these instructions and used only for domestic household cleaning to remove DRY dirt and dust from household carpets, flooring and fabrics. This cleaner is not fit to be used as an industrial cleaner, and is not designed for the collection of vitreous building material including particle board, construction products and similar products such as wood/fibres, cement, fillers, fibre glass etc or excessive or frequent sand. The infrequent pick-up of these materials in these circumstances may be harmful to your cleaner and may void the manufacturer s warranty. Accessories and consumables including dust bags and filters, unless defective in manufacture, are not subject to this warranty. In order to prolong the life of accessories and consumables, regular care and maintenance is recommended. When properly used and cared for, your cleaner will render excellent service; refer to the instruction manual for further details, as misuse or failure to follow the instructions makes this warranty void. In the event of service or advice being needed, please contact Hoover Floorcare Asia Pacific Pty Ltd, Level 1, Building 2 Brandon Business Park, 530 Springvale Road, Glen Waverley Victoria 3150, or on 1300 360 845, Monday-Friday 9am-5pm EST. The decision to repair or replace the cleaner is at the sole discretion of Hoover Floorcare. If Hoover Floorcare decide to repair or replace the cleaner, it will do so at its own cost. Hoover Floorcare is unable to accept responsibility under this warranty for any repair work not carried out by an authorised Hoover Service Agent or from the use of non-genuine parts. If any part is no longer available or manufactured, Hoover Floorcare will replace it with a genuine functional replacement part. This warranty does not apply to the cost of replacing any parts of the product due to normal wear and tear, alterations, improper installation, physical abuse, misuse or accidental damage. Any transportation costs involved in the repair of defective parts shall be borne by the claimant. If proof of purchase cannot be provided at the time of a warranty claim or service, any work carried out on the cleaner is chargeable. The repair or replacement of the cleaner under this warranty does not extend the original period of warranty. The benefits conferred by this warranty are in addition to all other rights and remedies in respect of the product as outlined under the Competition and Consumer Act and other State and Territory laws. Our goods come with guarantees that cannot be excluded in the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Call Hoover Floorcare with any product queries Australia 1300 360 845 New Zealand (09) 263 7573 To find out more about our range, visit: www.hoover.com.au www.hoover.co.nz email: sales@hooverfloorcare.com.au SAVE TIME, REGISTER WARRANTY ONLINE! www.hoover.com.au and www.hoover.co.nz V1 08/14