Innovation in Technology for Aircraft Maintenance and Fabrication Equipment, Solution Engineering, Research, Training RADIANT SYSTEMS for Anita Bonding Consoles P/N: GMIWRP-MKD011 Revised July 2012 GMI AERO - 9 rue Buffault 75009 Paris Tel : +33142821144 - Fax : +33142829838 Email : gmi@gmi-aero.com - Web : www.gmi-aero.com
RADIANT SYSTEMS for Anita Bonding Consoles, GMI AERO offers a selection of RADIANT equipment to meet a certain variety of use in a composite repair workshop. curing composite repair patch with epoxy resin drying resin, polymerization of paint, primer 1 CERAMIC RADIANT PANEL HEATER When a heating blanket cannot be used for bonding a composite repair, radiant panels constitute a very useful alternative. GMI designs very high quality radiant panels perfectly appropriate to composite repair bonding. This family identified as RAYBOND is designed to produce an even temperature distribution on the part. To allow an easy installation adjustable legs are mounted on each side; the leg position can be adapted so that two panels can be installed side by side to constitute a continuous heating panel.they can be adjusted in height. These panels are designed in terms of power to allow classical curings up to 120/180 C on a composite part Each panel is equipped with an input power stud; a cable is mounted (3 meters long) with a plug compatible to be connected to ANITA Bonding Console. Each panel has 4 adjustable legs; maximum adjustable height: 120 mm. Electrical Connection lead to the Anita for control Legs adjustable in position and height Table 1 :P/N and Definitions Dimensions P/N 30 x 30 cm GMIRP030030-1Z-V 40 x 40 cm GMIRP040040-1Z-V 50 x 50 cm GMIRP050050-1Z-V 60 x 60 cm GMIRP060060-1Z-V 2
2 INFRARED LAMP PANELS MOUNTED ON ARTICULATED ARM ASSEMBLY 2-1STANDARD MODELS This second family of radiant panels regroups models mounted on articulated arms to ease the positioning above complex and large parts. They are mainly used for paint, primers and small area curing of epoxies at low temperature (typically 120 C/250 F). They are proposed mounted on an articulated arm, itself on a rolling assembly. 2-2MODEL STANDARD FOR LARGE SURFACE Its design features provide a large surface coverage with good temperature distribution a. One cassette with 3 infra-red emitters b. high life duration of emitters due to permanent ventilation c. ventilation provides high security for the user d. 10000 hours life duration of emitters e. The panel can be controlled by Anita Bonding Console through direct connection like a heating blanket Figure 1: Articulated Model standard P/N:GMIWRP-MKD011-July 12 3
Connection for Anita Console control cable Figure 2 : Selection Switch and Modes: Left: Timer Mode; Right: Anita Control On the right we see the connection to the bonding console - see also pictures below 2-3TECHNICAL SPECIFICATIONS 1. Rated voltage: 220V - 240 V, 50/60 Hz Single Phase 2. Rated input (Nominal): 3 emitters, full power 3000 W 3. Heating elements: 3 quartz, tungsten filament, Infra Red emitters 4. Area of coverage: 1 m x 0.90 m larger surface for drying temperature (black sheet metal as reference) 5. Dimensions nominal: WxDxH: 95 x 164 x 150 cm 6. Weight: 46 kg 7. Noise level Less than 70 db 8. Max ambient temperature during operation 40 C 9. Max ambient temperature during storage and transportation 70 C 10.Manual mode with timer 4
2-4 xcontrol BY ANITA CONSOLE Figure 3: The infra red heating system is controlled by the Anita like a heating blanket thanks to our adapted interface All our panels are wired to be able to connect to our portable control unit (Anita Bonding Consoles). Our bonding control console will «see the system as an Infra Red Heater. Power connections P/N:GMIWRP-MKD011-July 12 5
are specifically designed. Power is fed to the heaters through a cable to connect safely (see picture below). A selection switch allows to select between Manual Mode with a Timer or Automatic with Anita Bonding Console control. FUSE Figure 4: Connection of the control cable from Anita Console 2-5TO ORDER The radiant system complete P/N: GMIWRP-01M-2 (230 Volts) 2-5.1 SPARES One tube for a cassette as replacement: To order: P/N: GMIWRP-01M-ST-01 (230 Volts) Filter To order: P/N: GMIWRP-01M-F-01 6