Assembly Instructions CELESTIAL LARGE PENDANT General Materials: Glass & Iron Length: 70 cm Width: 70 cm Height: 58 cm Weight: 4.15 kg Picture shown for reference is in rouille finish. Important Safty Instructions For your safety it is very important that you read these instructions before installing this pendant - we strongly advise that you use a certified electrician for both consultation and installation. 1. Use an authorised and certified electrician for consultation and installation. 2. This pendant has been rated for 12 x 7.5-watt maximum (90W). S11-E12-7.5W x 12 S11-E14-7.5W x 12 To avoid the risk of fire, do not exceed the recommended wattage. 3. Check your ceiling capacity. The ceiling must be able to support at least 5 times the weight of the ceiling light. For this light, a ceiling capacity of at least 20.75 kg is required. 4. The manufacturer and distributer accept no liability for incorrect installation. 5. For indoor use only. 6. Keep out of reach of children. 7. Remember to turn off your electricity supply at main circuit panel before installing. Do not reconnect the electricity supply until your light is fully assembled and installed. 8. All wires are connected inside the light. Do not remove the pendant from its packaging by pulling on the power cord, as this could affect the connection. 9. To reduce the risk of electric shock or personal injury, always switch the light off and allow it to cool down before replacing light bulbs. Do not touch or look directly at the light bulbs when the light is turned on. 10. To reduce the risk of fire, do not place flammable materials near the light bulbs. 11. Ignoring these instructions may result in a risk of fire or personal injury. 1
Your pendant has been handcrafted with pride and care. These instructions are designed to make assembly as easy as possible, so make yourself a cup of tea, sit down and take some time to read through them before you start. Assembly: What s in the Box PART DIAGRAM DESCRIPTION QTY. PART DIAGRAM DESCRIPTION QTY. (A1) Ceiling Plate (E) Bulbs + Spare 2+4 () (A3) Canopy Cap Nuts... 2 You also need (F) Junction Box (B) Fixture (G) Mounting Screws... 2 sets (C) Metal Tubes... 3 (H1) Wire Nuts... 3 or (D) Fixture 2 (H2) Terminal Box & Cross-head Screwdriver A Qualified Electrician Warning Before You Start Turn OFF the power to the junction box at your main circuit panel. Carefully unpack the box (lift the body out by the frame, not the power cord) and lay out all the parts on a flat surface. Tips Estimated assembly time: 15 minutes Wear gloves. Protect your light from marks and fingerprints when handling, for maximum sparkle and drama. Remove all the plastic wrapping. Steps Step 1: Mount the Light You need: Drill, screwdriver, parts A & G 1. Unscrew the cap nuts (A3) on the canopy () and remove the ceiling plate (A1). F 2. Drill 2 holes into the ceiling according to the ceiling plate (A1). 3. Position the ceiling plate (A1) onto the ceiling and fix it in place with mounting screws (G). A1 G A3 Assembly Instructions - Celestial Large Pendant 2
Step 2: Hang the Fixture You need: Parts, B & C 1. Screw in a metal tube (C) into the fixture (B). 2. Connect the remaining two tubes (C) one by one to the tube joined to the fixture so that they become one piece. 3. Fasten the tubes with the fixture to the canopy (). C B Step 3: Fix the Canopy You need: Parts, A3, H1 & H2 1. Connect the wires to the ceiling wires, referring to Wire & Safety Guidelines, using either wire nuts (H1) or a terminal box (H2). 2. Move the canopy () up to the ceiling and tighten the cap nuts (A3). H1 H2 A3 Assembly Instructions - Celestial Large Pendant 3
Step 4: Add Bulbs 1. You need: Part B & E 2. Screw in the light bulbs (E). Step 5: Add Glass Shades 1. You need: Parts B & D 2. Add glass shades (D) to cover the light bulbs (E). D E Assembly Instructions - Celestial Large Pendant 4
Finish Once the pendant is installed, switch on the light to test it. Sit back, relax, and enjoy. It s time to get your friends over and show them your new centrepiece. Care Advice Flast Brass / Matt Black / Natural Metal / Rouille Frame 1. Clean regularly with a clean, soft, slightly damp cloth. Wipe dry. 2. Wipe up any spills immediately. 3. Avoid the use of chemical and abrasive cleaners. 4. Do not use steel wool or scouring pads as they may scratch the surface. Clear Glass 1. Clean regularly with a soft, slightly damp cloth. Wipe dry with a clean, dry cloth. 2. Wipe up spills immediately 3. Glass cleaner may be used on clear glass, do not use on glass with a coloured finish. Take care not to spray the metal frame with the glass cleaner. 4. Avoid the use of chemical and abrasive cleaners. 5. Do not use steel wool or scouring pads as they may scratch the surface of the glass. Environment Discarding this light may require special waste handling. Please contact your local authorities for more information. haloest.com Assembly Instructions - Celestial Large Pendant 5
P.1 of 2 CELESTIAL PENDANT Description Raw lightweight industrial design meets delicate outer bulbs in glass. Inspired by Atom pendant design from the 70 s. Available in compact or large sizes, versatile collection in 4 finishes, Natural, Rouille (rust coating), matt black and flat brass. As shown in: Large, Rouille L W H Weight Watt Bulbs Small 50 50 33 3 kg 45 6 Large 70 70 58 4 kg 90 12 Specification Material: Bulb Type 200-240V*: Bulb Type 100-120V**: Iron and Glass Type B E14 7.5W Clear (Halogen) Type B E12 7.5W Clear (Incandescent) Available Finishes: Clear Glass and Rouille (coated Rust) / Flat Brass / Matt Black / Natural *200-240V = Europe/Asia/Australia **100-120V = USA HOME PAGE CHANDELIER PENDANT 57
P.2 of 2 CELESTIAL PENDANT Small General Dimension 50 L x 50 W x 33 H cm Large General Dimension 70 L x 70 W x 58 H cm HOME PAGE CHANDELIER PENDANT 58
Assembly Instructions CELESTIAL SMALL PENDANT General Materials: Glass & Iron Length: 50 cm Width: 50 cm Height: 33 cm Weight: 3.28 kg Picture shown for reference is in flat brass finish. Important Safty Instructions For your safety it is very important that you read these instructions before installing this pendant - we strongly advise that you use a certified electrician for both consultation and installation. 1. Use an authorised and certified electrician for consultation and installation. 2. This pendant has been rated for 6 x 7.5-watt maximum (45W). S11-E12-7.5W x 6 S11-E14-7.5W x 6 To avoid the risk of fire, do not exceed the recommended wattage. 3. Check your ceiling capacity. The ceiling must be able to support at least 5 times the weight of the ceiling light. For this light, a ceiling capacity of at least 16.4 kg is required. 4. The manufacturer and distributer accept no liability for incorrect installation. 5. For indoor use only. 6. Keep out of reach of children. 7. Remember to turn off your electricity supply at main circuit panel before installing. Do not reconnect the electricity supply until your light is fully assembled and installed. 8. All wires are connected inside the light. Do not remove the pendant from its packaging by pulling on the power cord, as this could affect the connection. 9. To reduce the risk of electric shock or personal injury, always switch the light off and allow it to cool down before replacing light bulbs. Do not touch or look directly at the light bulbs when the light is turned on. 10. To reduce the risk of fire, do not place flammable materials near the light bulbs. 11. Ignoring these instructions may result in a risk of fire or personal injury. 1
Your pendant has been handcrafted with pride and care. These instructions are designed to make assembly as easy as possible, so make yourself a cup of tea, sit down and take some time to read through them before you start. Assembly: What s in the Box PART DIAGRAM DESCRIPTION QTY. PART DIAGRAM DESCRIPTION QTY. (A1) Ceiling Plate (E) Bulbs + Spare... 6+2 () (A3) Canopy Cap Nuts... 2 You also need (F) Junction Box (B) Fixture (G) Mounting Screws... 2 sets (C) Metal Tubes... 3 (H1) Wire Nuts... 3 or (D) Fixture... 6 (H2) Terminal Box & Cross-head Screwdriver A Qualified Electrician Warning Before You Start Turn OFF the power to the junction box at your main circuit panel. Carefully unpack the box (lift the body out by the frame, not the power cord) and lay out all the parts on a flat surface. Tips Estimated assembly time: 15 minutes Wear gloves. Protect your light from marks and fingerprints when handling, for maximum sparkle and drama. Remove all the plastic wrapping. Steps Step 1: Mount the Light You need: Drill, screwdriver, parts A & G 1. Unscrew the cap nuts (A3) on the canopy () and remove the ceiling plate (A1). F 2. Drill 2 holes into the ceiling according to the ceiling plate (A1). 3. Position the ceiling plate (A1) onto the ceiling and fix it in place with mounting screws (G). A1 G A3 Assembly Instructions - Celestial Small Pendant 2
Step 2: Hang the Fixture You need: Parts, B & C 1. Screw in a metal tube (C) into the fixture (B). 2. Fasten the tube with the fixture to the canopy (). C B Step 3: Fix the Canopy You need: Parts, A3, H1 & H2 1. Connect the wires to the ceiling wires, referring to Wire & Safety Guidelines, using either wire nuts (H1) or a terminal box (H2). 2. Move the canopy () up to the ceiling and tighten the cap nuts (A3). H1 H2 A3 Step 4: Add Bulbs 1. You need: Part B & E 2. Screw in the light bulbs (E). Step 5: Add Glass Shades 1. You need: Parts B & D 2. Add glass shades (D) to cover the light bulbs (E). D E Assembly Instructions - Celestial Small Pendant 3
Finish Once the pendant is installed, switch on the light to test it. Sit back, relax, and enjoy. It s time to get your friends over and show them your new centrepiece. Care Advice Flast Brass / Matt Black / Natural Metal / Rouille Frame 1. Clean regularly with a clean, soft, slightly damp cloth. Wipe dry. 2. Wipe up any spills immediately. 3. Avoid the use of chemical and abrasive cleaners. 4. Do not use steel wool or scouring pads as they may scratch the surface. Clear Glass 1. Clean regularly with a soft, slightly damp cloth. Wipe dry with a clean, dry cloth. 2. Wipe up spills immediately 3. Glass cleaner may be used on clear glass, do not use on glass with a coloured finish. Take care not to spray the metal frame with the glass cleaner. 4. Avoid the use of chemical and abrasive cleaners. 5. Do not use steel wool or scouring pads as they may scratch the surface of the glass. Environment Discarding this light may require special waste handling. Please contact your local authorities for more information. haloest.com Assembly Instructions - Celestial Small Pendant 4