FOR SERVICE TECHNICIAN S USE ONLY

Similar documents
KAC - 57 TECHNICAL EDUCATION JOB AID W & 30 Built-In Single and Double Wall Ovens. Multimedia Enhanced

FOR SERVICE TECHNICIAN S USE ONLY

TECH SHEET DO NOT DISCARD PAGE 1. If unsuccessful entry into diagnostic mode, actions can be taken for specific indications:

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless testing requires power.

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless testing requires power.

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless testing requires power.

DIAGNOSTIC GUIDE DIAGNOSTIC TEST DISPLAY FAULT/ERROR CODES IMPORTANT. Activating the Diagnostic Test Mode. Before servicing, check the following:

TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

DIAGNOSTIC GUIDE DISPLAY FAULT/ERROR CODES E1 THERMISTOR OPEN IMPORTANT. Activating the Diagnostic Test Mode. Test Mode Functionality

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

TECH SHEET - DO NOT DISCARD PAGE 1 DIAGNOSTIC GUIDE

DIAGNOSTIC GUIDE DAMP DRY TEST

TECH SHEET - DO NOT DISCARD PAGE

TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

FOR SERVICE TECHNICIAN ONLY DO NOT REMOVE OR DESTROY

FOR SERVICE TECHNICIAN ONLY DO NOT REMOVE OR DESTROY WARNING

TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

Dacor Technical Service

NOTICE . SAFE SERVICING PRACTICES. Electric Wall Oven with Electronic Oven Control

30" BUILT-IN COMBINATION MICROWAVE WALL OVEN Models:

WARNING. Electrical Shock Hazard FOR SERVICE TECHNICIAN ONLY DO NOT REMOVE OR DESTROY L WASHER. Pub # /18/10 GE

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.

Technical Seminar HL-BD82S. Electric Built-In Oven. Panasonic Canada 2013

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires it.

KITCHENAID CONSUMER SERVICES Technical Training Department

DIAGNOSTIC GUIDE LESS DRY TEST

P MODEL AIR CONDITIONER

FOR SERVICE TECHNICIAN S USE ONLY

WARNING FOR SERVICE TECHNICIAN S USE ONLY

NN-A750WB NN-A720MB NN-A770SB 27L WHITE SILVER STAINLESS United Kingdom

SERVICE MANUAL MATRIX 18.2 CU FT TOP MOUNT REFRIGERATOR

Service Manual. Thermador Built-In Oven. for. Models: SMW272 B, SMW272S, SMW272W, SMW272P STOP TIME SELF CLEAN OVEN LIGHT COOK TIME BAKE OFF

OVEN PARTS For Models: KEMS378SBL05, KEMS378SWH05, KEMS378SSS05 (Black) (White) (Stainless)

OVEN PARTS For Models:KEMS308SBL05, KEMS308SWH05, KEMS308SSS05 (Black) (White) (Stainless)

11 05 litho in U.S.A. (cre) 1. Part No

OVEN PARTS For Models: JMW2427WB00, JMW2427WS00, JMW2427WW00 (Black) (Stainless) (White)

Activating the Test Mode. Test Mode Functionality

C Series Oven Training Program

OVEN PARTS For Models:YKEMC308KM02 (STAINLESS STEEL)

Training Bulletin May 2013

OVEN PARTS For Models:YKEHV309PS01, YKEHV309PM01 (Stainless Steel) (Meteorite)

OVEN PARTS. For Models: JMW2430WB02, JMW2430WS02, JMW2430WR02, JMW2430WW02, JMW2430WP02 (Black) (Stainless) (Oil Bronze) (White) (Pro Style)

OVEN PARTS For Models: KEMC308KBL04, KEMC308KWH04, KEMC308KBT04, KEMC308KSS04 (Black) (White) (Biscuit) (Stainless Steel)

OVEN PARTS For Models:YKEMC308KM0 (STAINLESS STEEL)

OVEN PARTS. For Models: JMW3430WB01, JMW3430WS01, JMW3430WR01, JMW3430WP01 (Black) (Stainless) (Oil Bronze) (Pro Style) Part No. W Rev.

VIKING SERVICE MANUAL

30" BUILT-IN ELECTRIC COMBINATION MICROWAVE WALL OVEN MODELS: WOC54EC0AB03 (Black) WOC54EC0AW03 (White) WOC54EC0AS03 (Stainless)

TABLE OF CONTENTS ELECTRIC BUILT-IN OVEN. Model No. HL-BD82S. Canada

KM-24 MICROHOOD COMBINATION

30" BUILT-IN ELECTRIC COMBINATION MICROWAVE WALL OVEN MODELS: WOC54EC0AB01 (Black) WOC54EC0AW01 (White) WOC54EC0AS01 (Stainless)

SERVICE MANUAL. KB-6524PS pictured KB-6525PS pictured

TECH SHEET - DO NOT DISCARD PAGE 1 COMPONENT TERMINAL TEST CONNECTOR P5-1 P5-3 APPLIANCE MANGER P2-6 K9 WARM DRAWER RELAY K3 BAKE IGNITER RELAY T3-3

TECH SHEET - DO NOT DISCARD PAGE 1

OVEN PARTS For Models:KEMC377KBL05, KEMC377KWH05, KEMC377KBT05, KEMC377KSS05 (Black) (White) (Biscuit) (S.Steel)

FOR SERVICE TECHNICIAN S USE ONLY

Service. Over The Range 2001 and 2002 Domestic Microwave Ovens. Models and manufacturing numbers in this manual models are listed in bold.

Installation Instructions

Training Manual MENUMASTERR C O M M E R C I A L M I C R O W A V E O V E N. 50 Hz Watt 50 Hz 1 March

SERVICE MANUAL R-820BK R-820BW SHARP CORPORATION DOUBLE GRILL 2 CONVECTION MICROWAVE OVEN MODELS

Products documentation (REVISION DATE: 03/10/2011) OMFP6010 (60cm PIROLITIC OVEN)

DryAire DRYING CABINET

MODELS TABLE OF CONTENTS

OVEN PARTS For Model: KEHU309SSS06 (Stainless)

Technical Service Guide

L-90. Multimedia Enhanced SERVICE MANUAL AMANA COMPACT WASHER WITH STAINLESS STEEL TUB. NTC3500FW* * represents engineering versions W A

ImPress IRONING STATION

Range Corporation 111 Front St., Greenwood, MS Tel: (888) S52M342O210SS

FOR SERVICE TECHNICIAN S USE ONLY

SERVICE MANUAL R-880B SHARP CORPORATION DOUBLE GRILL CONVECTION MICROWAVE OVEN MODEL

MSPA-MP METAPACK SERVICE MANUAL. Visual step-by-step guide to easily identify & correct technical problems! Gecko Electronics Inc.

Dishwasher Cycle Chart Condensation Dry System

Fast Track Troubleshooting

Hoshizaki America, Inc.

Washers and Dryers with Fifth Generation Solid State Electronic Control Systems

TECH SHEET - DO NOT DISCARD PAGE 1

WARNING DIAGNOSTIC GUIDE DIAGNOSTIC TESTS IMPORTANT ACTIVATING THE DIAGNOSTIC TEST MODE. DIAGNOSTIC: Saved Fault Codes. DIAGNOSTIC: Active Fault Codes

SERVICE MANUAL. for Thermador Professional Series Built-in Wall Ovens. Models: PO301, POD301, PO302, POD302, PODC302, POM301, POMW301

Technical Service Guide

Model OD302 Model OS302 MODELS A

Service. Compact Commercial Microwave Oven


CAUTION. To avoid risk of electrical shock, personal injury, or death, disconnect power to dishwasher before servicing. MDBTT50AW*

WARNING IMPORTANT DIAGNOSTIC GUIDE DIAGNOSTIC TESTS ACTIVATING THE DIAGNOSTIC TEST MODE. DIAGNOSTIC: Unsuccessful Entry

OWNER S MANUAL Manufactured Home Downflow Gas Furnace: MGD-B Series

Compact Range ESSE-N / A.S. April 2005

SERVICE MANUAL VC3ED FULL SIZE ELECTRIC CONVECTION OVEN - NOTICE -

Service. Electric Slide-In Range

30 & 36 FLUSH-MOUNT GAS COOKTOPS

! WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power to dishwasher before servicing.

TECH SHEET - DO NOT DISCARD PAGE 1

CONTROL BOARD PARTS. Illus. Part No. No. DESCRIPTION

Electric Slide-In Range JES8750BA* JES8850BA* JES8850BC* JES9750BA* JES9800BA* JES9860BA* JES9860BC* JES9900BA* JES9900BC*

OVEN PARTS For Models:WOC95EC0AB00, WOC95EC0AW00, WOC95EC0AS00, WOC95EC0AE00, WOC95EC0AH00 (Black) (White) (Stainless) (Black Ice) (White Ice)

Service Countertop Domestic Microwave Ovens

! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power.

SERVICE DATA SHEET (9704) Rev. D

Technical Information- Dishwasher MDB8750AWB MDB8750AWQ MDB8750AWS MDB8750AWW MDB9750AWB MDB9750AWQ MDB9750AWS MDB9750AWW

Transcription:

Tech Sheet FOR SERVICE TECHNICIAN S USE ONLY Do not discard DANGER WARNING Electrical Shock Hazard Only authorized technicians should perform diagnostic voltage measurements. After performing voltage measurements, disconnect power before servicing. Failure to follow these instructions can result in death or electrical shock. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before Failure to do so can result in death or electrical shock. Voltage Measurement Safety Information When performing live voltage measurements, you must do the following: Verify the controls are in the off position so that the appliance does not start when energized. Allow enough space to perform the voltage measurements without obstructions. Keep other people a safe distance away from the appliance to prevent potential injury. Always use the proper testing equipment. After voltage measurements, always disconnect power before servicing. IMPORTANT: Electrostatic Discharge (ESD) Sensitive Electronics ESD problems are present everywhere. ESD may damage or weaken the electronic control assembly. The new control assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress. Use an antistatic wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the appliance -OR- Touch your finger repeatedly to a green ground connection point or unpainted metal in the appliance. Before removing the part from its package, touch the antistatic bag to a green ground connection point or unpainted metal in the appliance. Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only. When repackaging failed electronic control assembly in antistatic bag, observe above instructions. W0767738B FOR SERVICE TECHNICIAN S USE ONLY

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY a. Do not operate or allow the oven to be operated with the door open. b. Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary:. Interlock Operation. Proper Door Closing 3. Seal and Sealing Surfaces (Arcing, Wear and Other Damage) 4. Damage to or Loosening of Hinges and Latches 5. Evidence of Dropping or Abuse c. Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, waveguide or transmission line, and cavity for proper alignment, integrity and connections. d. Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in service manual before the oven is released to the owner. e. A microwave leakage check to verify compliance with the CSA should be performed on each oven prior to release to the owner. f. Do not attempt to operate the oven if the door glass is broken.

IMPORTANT: Before powering MWO magnetron, be sure that a load, such as a microwave-safe cup of water, is present in the microwave oven cavity. Unplug oven or disconnect power before performing the following checks: A potential cause of a control not functioning is corrosion on connections. Observe connections and check for continuity with an ohmmeter. All tests/checks should be made with a VOM or DVM having a sensitivity of 0,000Ω per volt DC or greater. Check all connections before replacing components, looking for broken or loose wires, failed terminals, or wires not pressed into connectors far enough. Damaged harness must be entirely replaced. Do not rework a harness. Resistance checks must be made with power cord unplugged from outlet, and with wiring harness or connectors disconnected. IMPORTANT: Do not replace the control if there is no evidence of any failure. To Enter Diagnostics Mode: Before proceeding with any corrective action, perform the following steps to enter the Diagnostics Mode.. Enter Diagnostics Mode by pressing LOWER OVEN>LOWER LIGHT>OVEN CANCEL (repeat two more times) TIP: You can also swipe your finger from left to right over the buttons 3 times. NOTE: You do not need to wait for any audible or visual feedback from the control between keypad presses.. If control does not enter Diagnostics, continue repeating the keypad sequence from Step. All the keypads will light up when the control enters Diagnostics. 3. From the Diagnostic Menu, scroll to the desired selection using the touch screen. Error Diagnostics: View and clear the failure Component Activation: Manually activate each relay. Sensors & Switches: View the traditional oven cavity temperatures and door/latch switch status. System Information: View the model number, serial number, and software versions. Wi-Fi: View Wi-Fi related content such as IP Address, Gateway, SSID, and connection status. Exit Diagnostics Diagnostics General Procedure: Error Codes NOTE: All failures are stored in the failure To check if the error code is still present, start a cooking function and wait minute to check if the error appears.. Plug in oven or connect power.. Enter Diagnostics Mode. 3. Touch or scroll to Error Diagnostics in the Diagnostics menu, and then touch OK. 350 4. To clear error codes, touch Clear History. 5. If no failures are listed, the message No Error will appear on the screen. General Procedure: Component Activation. Plug in oven or connect power.. Enter Diagnostics Mode. 3. Touch or scroll to Component Activation in the Diagnostics menu, and then touch OK. 4. Touching the following selections will activate/ deactivate corresponding relay. 3

Selection MW Light MW Turntable MW Cooling Fan MW Grill MW Convection Element FOR SERVICE TECHNICIAN S USE ONLY MW Convection Fan MW Magnetron/ Cooling Fan Oven Bake Element Oven Broil Element Convection Element - Up Convection Element - Low Convection Fan HS - Up Convection Fan LS - Up Convection Fan HS - Low Convection Fan LS - Low Oven Cooling Fan High Speed Oven Cooling Fan Low Speed Oven Light Oven Door Latch Motor Relay MW Light Relay MW Turntable Relay MW Cooling Fan Relay MW Broil Element Relay MW Convection Element Relay MW Convection fan Relay MW Magnetron and MW Cooling Fan Relay Oven Bake Element Relay Oven Broil Element Relay Upper Convection Element Relay Lower Convection Element Relay Upper High Speed Convection Fan Relay Upper Low Speed Convection Fan Relay Lower High Speed Convection Fan Relay Lower Low Speed Convection Fan Relay General Procedure: Sensors & Switches NOTE: This procedure is to view the current status of oven switches and sensor readings. Display MW Door Switch MW Cavity Temp Oven Door Switch Oven Latch Switch Oven Cavity Temp Oven Meat Probe Temp Oven Cooling Fan High Speed Relay Oven Cooling Fan Low Speed Triac Oven Light Triac Oven Door Latch Motor Relay Status Open or Closed Degrees in Celsius Open or Closed Open or Closed Degrees in Celsius Degrees in Celsius. Plug in oven or connect power.. Enter Diagnostics Mode. 3. Touch or scroll to Sensors & Switches in the Diagnostics menu, and then touch OK. 4 4. Touch or scroll through the Sensors & Switches menu to view the desired status. NOTE: Touching Back will return the display to the main Diagnostics menu. General Procedure: System Information NOTE: This procedure is to view the following system information: System Display Information Model # Serial # UI Serial # Oven ACU Serial # UI Version HMI Central SW HMI Left SW HMI Left EE HMI Right SW HMI Right EE Kernel Version Touch Calibration Version Database Version Audio Version Oven ACU SW MWO ACU SW Diagnostics Entries Model Information Product Serial Number User Interface Serial Number Appliance Control Unit Serial Number User Interface Software Version HMI Central Board Software Version HMI Left Keyboard Software Version HMI Left Keyboard EEPROM Version HMI Right Keyboard Software Version HMI Right Keyboard EEPROM Version HMI Central Board Software Version LCD/TP FPC Tail Software Version HMI Central Board Database Structure HMI Central Board Software Version Oven Appliance Control Unit Software Version Microwave Oven Appliance Control Unit Software Version Number of times Diagnostic Menu has been entered. Plug in oven or connect power.. Enter Diagnostics Mode. 3. Touch or scroll to System Information in the Diagnostics menu, and then touch OK. 4. Touch or scroll through the System Information menu to view the desired status. NOTE: Touching Back will return the display to the main Diagnostics menu. General Procedure: Model Selection NOTE: When a new User Interface is installed, you will be prompted to select a new model number upon power up. To change the model number on an existing UI, follow the steps below.. Plug in oven or connect power.. Enter Diagnostics Mode. 3. Touch or scroll to System Information in the Diagnostics menu, and then touch OK. 4. Touch or scroll to Model Number, and then touch OK. 5. Touch or scroll to the correct model number in the list, and then touch Select.

Switch Mode No Display - control is blank Power Supply (SMPS), User Interface (UI) oven (power Off, wait 0 seconds, and then power On).. Remove plastic cover from UI. Check connection from display to UI. 3. Check wiring from main line to SMPS (CONN 7). NLL HMI Left J6 CONN7 6 SMPS 5 4 4 V DC 3 5W CONN YL BU Line 0A Fuse P3 P33 Line BR Filter L 4 4 5 BU P3 P34 Cavity Thermostat J4 User Interface J5 34 345P6 4 P 3 Microwave Appliance Manager 4. Check the wiring harness connection at UI (J5). 5. Check proper voltage input at J5- (GND) to J5-4 (4 VDC) on the UI by completing the following steps: 6. Connect voltage measurement equipment to J5- and J5-4 on UI. 7. Plug in oven or reconnect power. 8. Measure voltage and confirm voltage reading is 4 VDC. If voltage is correct, unplug oven or disconnect power and go to Step 3. If voltage is not correct, go to Step 9. 9. Unplug oven or disconnect power. Replace the SMPS. 0. Reassemble all parts and panels before. Plug in oven or reconnect power.. Check for control board display. If still no display, unplug oven or disconnect power. 3. Replace HMI-Central/UI board. 4. Reassemble all parts and panels before 5. Plug in oven or reconnect power. If the UI was replaced, follow the on-screen prompts to select the model number. 6. Verify operation is normal. If problem persists, replace the Control Panel Assembly and repeat steps 4 through 6. User Interface not reacting to touch Control Panel Assembly oven (power Off, wait 0 seconds, and power On).. Enter the Diagnostic Menu, and then touch POWER.. To reset Touch Calibration: unplug oven or disconnect power, wait 0 seconds, and then plug in oven or reconnect power. If still no response, go to Step 3. 3. Unplug oven or disconnect power. 4. Replace Control Panel Assembly. 6. Plug in oven or reconnect power. 7. Verify operation is normal. J5 OR YL Failure/Error Display Codes OR YL OR J7 HMI Right Control Panel Assembly BR OR P 345 J8 Oven Appliance Manager 5 Speaker, Control Panel No Sound Assembly oven (power Off, wait 0 seconds, and power On).. Verify sound is enabled. Touch the Tools menu, and then scroll to the Sound Menu. Confirm Key Press, Timer & Alert, and Power On & Off actions are all turned on and set to the desired volume.. Unplug oven or disconnect power. 3. Confirm the speaker is firmly connected to the HMI- Central/UI board at J8. If speaker is firmly connected, go to the Step 4. If speaker connection is loose, reconnect and proceed to Step 5. Speaker J8 HMI-C User Interface 4. Replace speaker. 6. Plug in oven or reconnect power. 7. Confirm operation of the speaker. If problem persists, unplug oven or disconnect power, replace Control Panel Assembly, and repeat steps 5 through 7. F Internal E0 Oven User Interface (UI) Failure oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics. NOTE: If other error codes are stored, troubleshoot those other error codes first.. Confirm the control panel assembly is grounded to the oven chassis. If it is, go to Step 6. If it is not, fix the connection. 3. Reassemble all parts and panels before 4. Plug in oven or reconnect power and cycle power. 5. If error persists, unplug oven or disconnect power. 6. Replace HMI-Central/UI board. 7. Reassemble all parts and panels before 8. Plug in oven or reconnect power and cycle power. 9. If error persists after HMI-Central/UI board is replaced, unplug oven or disconnect power and replace Control Panel Assembly. 0. Reassemble all parts and panels before. Plug in oven or reconnect power. Follow the onscreen prompts for model selection.. Verify operation is normal. Enter Diagnostics Mode, select Error Diagnostics, and clear the If the Control Panel Assembly was replaced, there is no need to clear the error

F E Internal Oven ACU Error oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics. NOTE: If other error codes are stored, troubleshoot those other error codes first.. Replace Copernicus Appliance Manager. 3. Reassemble all parts and panels before 4. Plug in oven or reconnect power. 5. If error persists after Copernicus Appliance Manager is replaced, unplug oven or disconnect power, and then go to Step 6. If not, go to Step 0. 6. Replace Control Panel Assembly. 7. Reassemble all parts and panels before 8. Plug in oven or reconnect power. 9. Follow the on-screen prompts to select the model number 0. Verify operation is normal. Enter Diagnostics Mode, select Error Diagnostics, and clear the If the Control Panel Assembly was replaced, there is no need to clear the error F E4 Microwave Oven Relay 4903 Error oven (power Off, wait 0 seconds, and then power On). After powering on, be sure that a load, such as a microwavesafe cup of water, is present in the microwave oven cavity, and start a microwave cooking function. Wait minute, and then verify that the failure happens again.. Make sure that all interlock switches works properly: when door is open, microwave light is On; when door is closed, microwave light is Off.. Unplug oven or disconnect power. 3. Check the following on the Microwave Appliance Manager: a. Wire connections to Relay 4903. Line Fuse 0A BR L Primary 4 Interlock Switch Microwave Relay 4903 Inverter b. Check if Relay 4903 is shorted. If so then go to Step 7. 4. Reassemble all parts and panels before 5. Plug in oven or reconnect power. 6. To check if the error code is still present, be sure that a load, such as a microwave-safe cup of water, is present in the microwave oven cavity, and start a cooking function in the microwave oven. Wait minute to check if the error appears. If error remains, go to Step 7. If not, go to Step 0. 7. Unplug oven or disconnect power and replace the Microwave Appliance Manager. 8. Reassemble all parts and panels before 9. Plug in oven or reconnect power. 0. Verify operation is normal. Enter the Diagnostics BU CN70 F E5 Microwave Oven Inverter Error oven (power Off, wait 0 seconds, and then power On). After powering on, be sure that a load, such as a microwavesafe cup of water, is present in the microwave oven cavity, and start a microwave cooking function. Wait minute, and then verify that the failure happens again.. Make sure that all interlock switches works properly: when door is open, microwave light is on; when door is closed, microwave light is off.. Unplug oven or disconnect power. 3. Check the following connections on Microwave Appliance Manager: a. Relay 4903. b. Connector P8. P8 To MW Relay 4903 P355 P354 3 BU 3 CN70 Magnetron CN70 MW Inverter PWM CN703 E70 YL/ GN 4. Check the following connections on the Inverter board: a. CN70. b. CN70. c. CN703. 5. If the door works properly and all connections are okay, replace the Microwave Inverter Board. 6. Reassemble all parts and panels before 7. Plug in oven or reconnect power. 8. To check if the error code is still present, be sure that a load, such as a microwave-safe cup of water, is present in the microwave oven cavity, and start a cooking function in the microwave oven. Wait minute to check if the error appears. If error remains, then go to Step 9. If not, go to Step 7. 9. Unplug oven or disconnect power. 0. Replace the Magnetron.. Reassemble all parts and panels before. Plug in oven or reconnect power. 3. To check if the error code is still present, be sure that a load, such as a microwave-safe cup of water, is present in the microwave oven cavity, and start a cooking function in the microwave oven. Wait minute to check if the error appears. If error remains, then go to Step 4. If not, go to Step 7. 4. Unplug oven or disconnect power and replace the Microwave ACU. 6. Plug in oven or reconnect power. 7. Verify operation is normal. Enter the Diagnostics 6

F E6 Microwave Generation Error oven (power Off, wait 0 seconds, and then power On). After powering on, be sure that a load, such as a microwavesafe cup of water, is present in the microwave oven cavity, and start a microwave cooking function. Wait minute, and then verify that the failure happens again.. Make sure that all interlock switches works properly: when door is open, microwave light is on; when door is closed, microwave light is off.. Unplug oven or disconnect power. 3. Check the following connections on Microwave Appliance Manager: a. Relay 4903. Line Fuse 0A BR L Primary 4 Interlock Switch Microwave Relay 4903 Inverter 4. If the door works properly and all connections are okay, replace the Magnetron. 6. Plug in oven or reconnect power. 7. To check if the error code is still present, be sure that a load, such as a microwave-safe cup of water, is present in the microwave oven cavity, and start a cooking function in the microwave oven. Wait minute to check if the error appears. If error remains, then go to Step 8. If not, go to Step 6. 8. Unplug oven or disconnect power and replace the Inverter Board. 9. Reassemble all parts and panels before 0. Plug in oven or reconnect power.. To check if the error code is still present, be sure that a load, such as a microwave-safe cup of water, is present in the microwave oven cavity, and start a cooking function in the microwave oven. Wait minute to check if the error appears. If error remains, then go to Step. If not, go to Step 6. 3. Replace the Microwave ACU. 4. Reassemble all parts and panels before 5. Plug in oven or reconnect power. 6. Verify operation is normal. Enter the Diagnostics BU CN70 7 F E0 Keypad disconnected Keypad E Stuck/shorted key oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics.. Check that connectors J4, J5, J6, and J7 are firmly connected. If they are not, go to Step 3. If they are, go to Step 6. HMI Left J6 J4 User Interface J7 HMI Right 3. Reconnect any loose connectors. 4. Reassemble all parts and panels before 5. Plug in oven or reconnect power. If the failure is gone, go to Step 9. If the failure is still present, unplug oven or disconnect power. 6. Replace the Control Panel Assembly. 7. Reassemble all parts and panels before 8. Follow the on-screen prompts to select the model number 9. Verify operation is normal. Enter Diagnostics Mode, select Error Diagnostics, and clear the If the Control Panel Assembly was replaced, there is no need to clear the error F3 E0 Main oven sensor open or shorted Sensors oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics.. Disconnect connector P3 from Oven Appliance Manager, and measure the resistance of the sensor between P3- and P3-. Test for 000Ω to 00Ω at 77 F (5 C). Check sensor for short to ground. If checks on sensor are not correct, replace sensor and repeat the checks. Oven Temperature Sensor Speaker J8 V V 3 3. Reassemble all parts and panels and plug in oven or reconnect power. 4. Enter the Diagnostics Menu and select Sensors & Switches to verify if the temperature shown in the Cavity Temp display is correct (ambient temperature). If it is, go to Step 8. If it is not, unplug oven or disconnect power. NOTE: On the status screen, the unit of measurement is Celsius. 5. Replace the Copernicus Appliance Manager board. 6. Reassemble all parts and panels before J5 J5 3 4 Control Panel Assembly 4 5 6 7 8 9 0 P3 Copernicus Appliance Manager

7. Plug in oven or reconnect power. 8. Verify operation is normal. Enter the Diagnostics Menu, select Error Diagnostics, and clear the F3 Sensors E3 Meat Probe Connector Jack or Meat Probe Shorted oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics.. Remove meat probe if connected. 3. Disconnect connector P3 from Copernicus Appliance Manager. Meat Probe Sensor OR GN Copernicus Appliance Manager 4. Check connector jack resistance between P3-3 and P3-4. If it is 0Ω, change the jack assembly, and then go to Step 5. If it is not 0Ω, the jack assembly is working properly. Go to Step 5. 5. Plug in the meat probe and check for short to ground or open. If checks on meat probe are not correct, replace the meat probe. At 77 F (5 C) the expected value is approximately 50KΩ. If they are correct, replace the Copernicus Appliance Manager. 6. Reassemble all parts and panels before 7. Plug in oven or reconnect power. 8. Verify operation is normal. Enter the Diagnostics Check the meat probe reading by entering the Diagnostics Menu and selecting Sensors & Switches. The meat probe should detect the ambient temperature. 3 4 5 6 7 8 9 0 P3 F4 E Microwave Cavity Temperature Sensor Error oven (power Off, wait 0 seconds, and then power On). After powering on, be sure that a load, such as a microwavesafe cup of water, is present in the microwave oven cavity, and start a microwave cooking function that uses the temperature sensor, such as a Convect cycle. Wait minute, and then verify that the failure happens again.. Check that the P connection of the Microwave Appliance Manager is firmly connected. If it is, go to Step 3. If it is not, reconnect and go to Step 5. Cavity Thermistor Microwave Appliance Manager P 3. Disconnect connector P from the Microwave Appliance Manager, and measure the resistance of the thermistor. It should be (approximately) 30kΩ at 77 F ± 0 F (5 C ± 0 C). 4. Check thermistor for short to ground. If check on thermistor is not correct, replace the thermistor. If thermistor check is correct, replace the Microwave Appliance Manager. 6. Plug in oven or reconnect power. 7. Verify operation is normal. Enter the Diagnostics F4 E Magnetron Temperature Sensor Error oven (power Off, wait 0 seconds, and then power On). After powering on, be sure that a load, such as a microwavesafe cup of water, is present in the microwave oven cavity, and start a microwave cooking function. Wait minute, and then verify that the failure happens again.. Check that the P connection of the Microwave Appliance Manager is firmly connected. If it is, go to Step 3. If it is not, reconnect and go to Step 5. Magnetron Thermistor P Microwave Appliance Manager 8 3. Disconnect connector P from the Microwave Appliance Manager. Measure the resistance of the thermistor. It should be (approximately) 0kΩ at 77 F ± 0 F (5 C ± 0 C). 4. Check thermistor for short to ground. If check on thermistor is not correct, replace the thermistor. If thermistor check is correct, replace the Microwave Appliance Manager. 6. Plug in oven or reconnect power. 7. Verify operation is normal. Enter the Diagnostics

F4 Inputs E4 Microwave Oven Humidity Sensor Error oven (power Off, wait 0 seconds, and then power On). After powering on, be sure that a load, such as a microwavesafe cup of water, is present in the microwave oven cavity, and start a microwave cooking function that uses the humidity sensor, such as a Steam cycle. Wait minute, and then verify that the failure happens again.. Check that the P3 connection of the Microwave Appliance Manager is firmly connected. If it is, go to Step 3. If it is not, reconnect and go to Step 5. Humidity Sensor 600 Microwave Appliance Manager P3 3. Disconnect connector P3 from Microwave Appliance Manager and measure the resistance of the sensor: Between pins 3 and. It should be approximately 800Ω at 77 F ± 0 F (5 C ± 0 C). Between pins 3 and. It should be approximately 800Ω at 77 F ± 0 F (5 C ± 0 C). 4. Check sensor for short to ground. If checks on sensor are not correct, replace the sensor. If sensor checks are correct, replace the Microwave Appliance Manager. 6. Plug in oven or reconnect power. 7. Verify operation is normal. Enter the Diagnostics F4 E8 Inverter Over Temperature oven (power Off, wait 0 seconds, and then power On). After powering on, be sure that a load, such as a microwavesafe cup of water, is present in the microwave oven cavity, and start a microwave cooking function. Wait minute, and then verify that the failure happens again.. Check the following: a. Cooling fan connection for any loose connectors. b. Oven installation and make sure there is no air blockage at the bottom vent. 3. Reassemble all parts and panels before 4. Plug in oven or reconnect power. 5. To check if the cooling fan is stalled, be sure that a load, such as a microwave-safe cup of water, is present in the microwave oven cavity, and start a cooking function in the microwave oven. Make sure the fan is running. If it is not, unplug oven or disconnect power, replace the fan and go to Step 8. If it is, go to Step 6. 6. Unplug oven or disconnect power. 7. Replace the inverter board. 8. Reassemble all parts and panels before 9. Plug in oven or reconnect power. 0. Verify operation is normal. Enter the Diagnostics 9

F4 E9 Inverter and Magnetron Over Temperature oven (power Off, wait 0 seconds, and then power On). After powering on, be sure that a load, such as a microwavesafe cup of water, is present in the microwave oven cavity, and start a microwave cooking function. Wait minute, and then verify that the failure happens again.. Check the following: a. Cooling fan connection for any loose connectors. b. Oven Installation and make sure there is no air blockage at the bottom vent. 3. Reassemble all parts and panels before 4. Plug in oven or reconnect power. 5. To check if the cooling fan is stalled, be sure that a load, such as a microwave-safe cup of water, is present in the microwave oven cavity, and start a cooking function in the microwave oven. Make sure the fan is running. If it is not, unplug oven or disconnect power, replace the fan and go to Step 8. If it is, go to Step 6. 6. Unplug oven or disconnect power. 7. Replace the Magnetron and the inverter board. 8. Reassemble all parts and panels before 9. Plug in oven or reconnect power. 0. Verify operation is normal. Enter the Diagnostics F5 E0 Door and latch switch do not agree Inputs oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics.. Enter the Diagnostics Menu and select Component Activation. Touch or scroll to Door Latch Motor, and then touch OK. Touch Latch Door. Wait at least 5 seconds, and then check if latch status changes on screen. If status does not change, unplug oven or disconnect power and go to Step. If status changes, unplug oven or disconnect power and go to Step 5.. If the oven door did not unlatch, unplug connector P3 and check for continuity (on the latch wire) between P3-5 and P3-7. BU Motor Latch Switch Door Switch TN BR OR/ 3 4 5 6 7 8 9 0 P3 Copernicus Appliance Manager 3. Disconnect J8 connector from Copernicus Appliance Manager. 4. Measure the resistance between connectors J8- and P5-. It should be 500Ω to 3000Ω at 77 F (5 C). N Copernicus Appliance Manager 3 4 5 6 7 P5 YL Motor Door Latch J8 5. If the resistance check is outside the range, replace the affected door latch assembly. Verify that the error is gone. 6. Reassemble all parts and panels. 7. Plug in oven or reconnect power. 8. Enter the Diagnostics Menu and select Component Activation. Check the door status on the screen by opening and closing the oven door. 9. If status does not change, unplug the oven or disconnect power. 0. Check for continuity with door open and closed at P3-5 to P3-6. Door open = infinite resistance. Door closed = zero resistance.. If continuity check is not correct, replace the door latch assembly. If all checks were correct, replace Copernicus Appliance Manager.. Reassemble all parts and panels before 3. Plug in oven or reconnect power. 4. Verify operation is normal. Enter the Diagnostics 0

F5 E Latch not operating Inputs oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics.. Enter the Diagnostics Menu and select Component Activation. Touch or scroll to Door Latch Motor, and then touch OK. Touch Latch Door. Wait at least 5 seconds, and then check if latch status changes on screen. If status does not change, go to Step. If status changes, unplug oven or disconnect power, replace Copernicus Appliance Manager and go to Step 6.. If latch status on screen is open, unplug oven or disconnect power and check for loose harness connection between motor latch switch and P3-5 and P3-7. F6 E0 Oven user interface - lost communication Oven appliance manager - E6 lost communication oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics.. Check continuity of wirings between P-4 and J5-3, then P-5 and J5-. 3. Check for continuity between P- and P-. 4. If all checks are correct, replace Copernicus Appliance Manager. HMI Left J6 J4 User Interface J5 J7 HMI Right BU Motor Latch Switch Door Switch TN BR OR/ 3 4 5 6 7 8 9 0 P3 Copernicus Appliance Manager 3. Disconnect connector J8 from Copernicus Appliance Manager. 4. Measure the resistance between connectors J8- and P5-. It should be 500Ω to 3000Ω at 77 F (5 C). Copernicus Appliance Manager YL 3 4 5 6 7 P5 Motor Door Latch N N L L J5 3 4 Control Panel Assembly YL CONN7 CONN 6 5 YL BR OR P SMPS 3 4 3 4 5 4V DC BU 5 W Oven Appliance Manager OR 5. Reassemble all parts and panels. 6. Plug in oven or reconnect power. 7. If the error appears again, unplug oven or disconnect power. 8. Replace HMI-Central/UI board. 9. Reassemble all parts and panels before 0. Plug in oven or reconnect power.. Follow the on-screen prompts to select the model number if the UI was replaced.. Verify operation is normal. Enter the Diagnostics J8 5. If the resistance check is outside the range, replace the door latch assembly. Verify that the error is gone. If all checks were correct, replace Copernicus Appliance Manager. 6. Reassemble all parts and panels before 7. Plug in oven or reconnect power. 8. Verify operation is normal. Enter the Diagnostics

F6 E Over temperature oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics.. Check for elements shorted to ground. Check resistance of elements: a. PX4- and PX3- to check Broil element (3.Ω to 4.6Ω). b. PX- and PX3- to check Bake element (9Ω to Ω). c. PX-3 and PX3- to check Upper Conv element (5.Ω to 7.3Ω). d. PX-4 and PX3- to check Lower Conv element (5.Ω to 7.3Ω). 3. If any element is shorted to ground, replace the element. 4. Check for shorted relays. Disconnect PX, PX and PX4 connectors and check for shorts between: a. PX- and PX- (Bake relay). b. PX-3 and PX-4 (Up Convect relay). c. PX4- and PX4- (Broil relay). d. PX-3 and PX-4 (Low Convect relay). Copernicus Appliance Manager K K0 K K3 K BU Broil - 4000W PX4 Bake - 800W 3 4 YL Upper Convect - 3400W PX PX3 5. If there is a shorted relay, replace the Copernicus Appliance Manager. Go to Step 9. 6. If everything is correct, disconnect connector P3 from Copernicus Appliance Manager. 7. Measure the resistance of the oven sensor. It should be 000Ω to 00Ω at 77 F (5 C). BU YL / 3 4 PX YL Lower Convect - 3400W YL Temperature Limiter Open Temp 30 F (50 C) NLL 8. Check sensor for short to ground. If checks on sensor are not correct, replace sensor and repeat the checks. Oven Temperature Sensor V V 3 4 5 6 7 8 9 0 P3 Copernicus Appliance Manager 9. Reassemble all parts and panels before 0. Plug in oven or reconnect power.. Enter the Diagnostic Menu and select Sensors & Switches to verify that the corresponding oven temperature displayed is correct (ambient temperature). If not, unplug oven or disconnect power, and replace the Copernicus Appliance Manager board. NOTE: On the status screen, the unit of measurement is Celsius.. Reassemble all parts and panels before 3. Plug in oven or reconnect power. 4. Verify operation is normal. Enter the Diagnostics F6 E4 User Interface/Appliance Manager state status mismatch oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics.. Replace Copernicus Appliance Manager. 3. Reassemble all parts and panels before 4. Plug in oven or reconnect power. 5. Cycle power. If error persists after the Copernicus Appliance Manager is replaced, unplug oven or disconnect power. Go to Step 7. 6. If the error is gone, go to Step 0. 7. Replace the HMI-Central/UI board. 8. Reassemble parts and panels before 9. Plug in oven or reconnect power, and follow the onscreen prompts for model selection. 0. Verify operation is normal. If operation is normal, go to Step 4. If error still exists, go to Step.. Replace the control panel assembly. 3. Plug in oven or reconnect power. 4. Follow the on-screen prompts for model selection. 5. Verify operation is normal. Enter Diagnostics Mode, select Error Diagnostics, and clear the

F6 E8 Lost communications with Microwave Oven Appliance Manager oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics.. Make sure the oven is plugged in. Open microwave door to check if light comes on.. Ensure the Sabbath mode is disabled. 3. Unplug oven or disconnect power. 4. Check the connection between User Interface J5- (yellow) and J5-3 (orange) and Microwave Appliance Manager P6-3 (orange) and P6-4 (yellow). User Interface Wide/Power Nav 3 4 YL OR J5 F9 E0 Product not wired correctly oven (power Off, wait 0 seconds, and then power On). PROCEDURE: Before proceeding, verify the error code by entering the Diagnostics Menu and selecting Error Diagnostics.. Access the electrical wiring from the house power supply to the oven. 3. Check house wiring to the product. Check to see if the neutral connection is switched with L or L (refer to the Installation Instructions for product wiring). 4. Reassemble all parts and panels before 5. Plug in oven or reconnect power. 6. Verify operation is normal by running a cooking function. Enter the Diagnostics Menu, select Error Diagnostics, and clear the OR YL 3 4 5 P6 Microwave Appliance Manager 5. If harness is correct, replace the Microwave Appliance Manager. 6. Reassemble all parts and panels before 7. Plug in oven or reconnect power. 8. If the error appears again, unplug or disconnect power and replace HMI-Central/UI board. 9. Reassemble all parts and panels before 0. Plug in oven or reconnect power.. Follow the on-screen prompts to select the model number if the UI was replaced.. Verify operation is normal. Enter the Diagnostics 3

Microwave Oven Components Component Locations Upper Microwave Oven A B C E D F G H T S V U I J R K Q P O N M L A. Convect motor B. Convect thermostat (behind cover) C. Convect element D. Line filter E. Humidity sensor F. Magnetron fan motor G. Copernicus appliance manager (lower oven) H. Switch mode power supply (SMPS) I. Secondary interlock switch J. Turntable motor K. Broil element L. Microwave appliance manager M. Cavity halogen lamp N. Primary interlock switch O. Monitor interlock switch P. Magnetron thermistor Q. Magnetron R. Microwave light transformer S. Microwave inverter T. Cavity temperature sensor U. Grill thermostat V. Cavity thermostat Not shown: Monitor fuse, 0A line fuse 4

Lower Oven FOR SERVICE TECHNICIAN S USE ONLY A. HMI-Central/UI board B. Cooling fan C. Oven temperature sensor D. Convection assembly E. Temperature limiter F. Light assembly G. Bake element (hidden) H. Broil element I. Door lock assembly J. Control panel assembly K. WiFi antenna 5

Cooling Fan Relay Logic Oven High Speed Blower (Main/Upper or Lower) Oven Cooking - Cold - O Oven Cooking - Warm - O Oven Cooking - Hot O - Oven Self-Clean O - Oven Low Speed Blower (Main/Upper or Lower) Cold Warm Hot LEGEND Cavity Temperature is less than F (00 C) Cavity Temperature is between F and 599 F (00 C and 35 C) Cavity Temperature is greater than 599 F (35 C) Mode Bake Broil Upper Convect Ring Lower Convect Ring Upper Convect Fan Convect Frozen Pizza C C C C O O Convect Pastry C C C C C C Convect Slow Roast hrs C C C C O O Convect Slow Roast 8 hrs C C C C O O Convect Slow Roast 4 hrs C C C C O O Convect Roast C C C C O O Convect Broil - C - - C C Convect Bake C C C C C C Convect Bake- Rapid Preheat C C C C C C Bake C C C C C C Broil - C - - - - Keep Warm C C - - C C Rapid Proof C C - - - - Proof C C - - - - No Preheat C C C C C C True Convect C C C C C C Self Clean C C - - - - LEGEND Relay Off Relay Cycles Relay On Not Available - C O NA Lower Convect Fan 6

To properly check for voltage, complete the following steps:. Connect voltage measurement equipment to check points. Component Serviceable Side Component Testing Chart - Oven Check Points Copernicus 3. Plug in oven or reconnect power and confirm voltage reading. 4. Unplug oven or disconnect power. Results-Resistance Results-Voltage Lights Front P7- to L (J8-) 0-40Ω 0V Latch Switch Front P3-7 to P3-5 Open circuit Door Switch Front P3-6 to P3-5 Closed circuit with oven door closed Latch Motor Front P5- to N (J8-) 500 to 3000Ω 0V motor running Oven Temperature Sensor Front P3- to P3-075Ω at 68 F (0 C)DLB Meat Probe Side P3-3 to P3-4 9876-0075Ω Blower Motor - Rear PX- to L (J8-) 5Ω to 3Ω 0V motor running High Speed Blower Motor - Rear P7- to L (J8-) 5Ω to 3Ω 0V motor running Low Speed Thermal Limiter Rear PX3- to L (Main line) Closed circuit 0V closed, N/A open Thermal Fuse (only Front J8- to L Closed circuit 0V closed, N/A open for single/double) Upper Convection Rear P5-3 to N (J8-) 5 to Ω 0VAC motor running Fan - High Speed Upper Convection Rear P5- to N (J8-) 7 to 5Ω 0VAC motor running Fan - Low Speed Lower Convection Rear P5-5 to N (J8-) 5 to Ω 0VAC motor running Fan - High Speed Lower Convection Fan - Low Speed Rear P5-4 to N (J8-) 7 to 5Ω 0VAC motor running Upper Convection Element Lower Convection Element Front PX-3 to PX3-5. to 7.3Ω 40 VAC Convection cycle operating Front PX-4 to PX3-5. to 7.3Ω 40 VAC Convection cycle operating Bake Element Rear PX- to PX3-9.0 to.6ω 40V Bake cycle operating Broil Element Front PX4- to PX3-3.5 to 4.9Ω 40V Broil cycle operating User Interface Board Front J5- to J5-4 N/A 4 VDC Copernicus Appliance Manager Side (Combo) P- to P-5 N/A 4 VDC 7

NOTES: Disconnect the harness from the board before performing measurements. See the following table for connector pin identification. Pin Pin Pin Copernicus Appliance Manager PX3 Pin Pin Pin Pin PX4 P P3 P4 K3 P6 J8 P7 Pin K PX-4 K9 K9A K KA K KA K0 K0A K4 K5 K6 K7 K8 P5 PX- PX- PX-3 PX-4 PX-4 PX-3 PX- PX- Pin Harness Connector Pin PX- PX- PX-3 PX-4 PX- PX- PX-3 PX-4 Copernicus Appliance Manager Pin J J6 J3 J7 J9 J5 J8 J4 8

Component Appliance Manager Cavity Thermostat Magnetron Fan Motor Turntable Motor Monitor Fuse MW Light Transformer FOR SERVICE TECHNICIAN S USE ONLY Serviceable Side Top Component Testing Chart - Microwave Procedure Results - Resistance Check wiring to MW microwave appliance manager:. Unplug the microwave oven or disconnect power.. Visually inspect connectors on the microwave appliance manager, P, P, P8, P, P, P3, P6, P354, P355 and the top connectors (relays 4903, 4904 and 4905) to see whether there are signs of overheating or any signs of failure due to loose wires, bad crimping, etc. 3. Reassemble all parts and panels before 4. Plug in microwave oven or reconnect power. Top. Unplug microwave oven or disconnect power.. Remove wire leads. Top. Unplug microwave oven or disconnect power.. Remove wire leads. 3. Measure resistance (ohmmeter scale: Rx). Bottom. Unplug microwave oven or disconnect power.. Remove wire leads. 3. Measure resistance (ohmmeter scale: Rx). Top. Unplug microwave oven or disconnect power.. Remove wire leads. Top. Unplug microwave oven or disconnect power.. Remove wire leads. 3. Measure resistance (ohmmeter scale: Rx). Line Fuse Top. Unplug microwave oven or disconnect power.. Remove wire leads. Normal = Continuity Abnormal = Infinite Normal = 5Ω Abnormal = Infinite Normal =500Ω (approximately) Abnormal = Infinite Normal = Continuity Abnormal = Infinite Primary Winding = 40Ω (approximately) Secondary Winding = 0.4Ω (approximately) Normal = Continuity Abnormal = Infinite Component Location G V F J Not shown R Not shown 9

Component Primary Interlock Switch Secondary Interlock Switch Monitor Interlock Switch Halogen Light FOR SERVICE TECHNICIAN S USE ONLY Serviceable Side Procedure Results - Resistance Top Test :. Unplug microwave oven or disconnect power.. Disconnect the wires at the Primary Interlock Switch. 3. Check from the common terminal (brown wire) to the normally open terminal (yellow wire). 4. Reconnect the wires at the Primary Interlock Switch. Test :. Unplug microwave oven or disconnect power.. Disconnect the wires at the Primary Interlock Switch. 3. Check from the common terminal (brown wire) to the normally closed terminal (blue wire). 4. Reconnect the wires at the Primary Interlock Switch. Top. Unplug microwave oven or disconnect power.. Disconnect the wires at the Secondary Interlock Switch. 3. Check from the common terminal (blue wire) to the normally open terminal (white wire). 4. Reconnect the wires at the Secondary Interlock Switch. Top. Unplug microwave oven or disconnect power.. Disconnect the wires at the Monitor Interlock Switch. 3. Check from the common terminal (yellow wire) to the normally closed terminal (blue wire). 4. Reconnect the wires at the Monitor Interlock Switch. Top. Unplug microwave oven or disconnect power.. Remove wire leads. Test : Door Open = Infinite. Door Closed = Continuity. Test : Door Open = Continuity. Door Closed = Infinite Door Open = Continuity. Door Closed = Infinite Door Open = Continuity. Door Closed = Infinite Normal = approximately 3Ω Abnormal = Infinite Component Location N I O M 0

Component FOR SERVICE TECHNICIAN S USE ONLY Inverter Top Check wiring to MW inverter:. Unplug the microwave oven or disconnect power.. Visually inspect 4 connectors on the MW inverter boards, CN70, CN70, CN703 and E70 to see whether there are signs of overheating or any signs of failure due to loose wires, bad crimping, etc. 3. Reassemble all parts and panels before 4. Plug in microwave oven or reconnect power. Magnetron Top. Unplug microwave oven or disconnect power.. Remove wire leads. Check that the seal is in good condition. Line Filter Top. Unplug microwave oven or disconnect power.. Remove wire leads. Humidity Sensor Magnetron Thermistor Grill Thermostat Convect Thermostat Serviceable Side Procedure Results - Resistance Top. Unplug microwave oven or disconnect power.. Remove the 3-pin connector from MW Appliance Manager. 3. Measure resistance across pins and 3 and across pins and 3. 4. Replace the 3-pin connector from MW Appliance Manager.. Unplug microwave oven or disconnect power.. Remove wire leads. Top. Unplug microwave oven or disconnect power.. Remove wire leads. Rear. Unplug microwave oven or disconnect power.. Remove wire leads. Filament Terminals Normal = <Ω Filament to Chassis Normal = Infinite P3 to P3, P33 to P34 Normal >/= 300kΩ Abnormal </= 00kΩ P3 to P34, P3 to P33 Normal = 0Ω Abnormal >/= 00kΩ Normal =.8kΩ (approximately) at 77 F +/- 0 F (5 C +/- 0 C) Abnormal = Infinite. Normal = 0kΩ (approximately) at 77 F +/- 0 F (5 C +/-0 C) Abnormal = Infinite. Normal = Continuity Abnormal = Infinite Normal = Continuity Abnormal = Infinite Component Location S Q D E P U B

Component Broil Element Convect Element Cavity Temp Sensor Convect Fan Motor FOR SERVICE TECHNICIAN S USE ONLY Serviceable Side Procedure Results - Resistance Rear. Unplug microwave oven or disconnect power.. Remove wire leads. 4. Replace wire leads Rear. Unplug microwave oven or disconnect power.. Remove wire leads. Rear. Unplug microwave oven or disconnect power.. Remove wire leads. Rear. Unplug microwave oven or disconnect power.. Remove wire leads. Normal = 9Ω Abnormal = Infinite Normal = Ω Abnormal = Infinite Normal = 30KΩ (approximately) at 77 F ±0 F (5 C ±0 C) Abnormal = Infinite Normal = 48Ω Abnormal = Infinite Component Location K C T A

NOTES: End of line tester (EOL) is for manufacturing purposes only. Dots indicate connections or splices. Wiring Diagrams Circuit shown in STANDBY/OFF mode with oven door closed. All voltages in the wiring diagrams are designated as 0/40 VAC. If oven is connected to 0/08 VAC, replace 40V with 08V. N L L Grill r The mostat 4 P3 P33 Line Filter L P3 P34 BU 4 HMI Left 7 BR 7 BR J6 Speaker Primary Interlock 0A Switch Line Fuse BR 4 3 YL BR 4 Monitor Interlock 43 BU Switch Cavity Thermostat CONN7 CONN SMPS 4V DC 5W 4 5 BU 6543 J4 BU 8 BR 8 BR 4906 Turntable 84 83 490 Magnetron Fan Halogen Light 85 BR 490 86 BR MW Light Transformer Conv. Thermoactuator 8 BU J8 YL 80 Conv. Fan 89 3 YL Magnetron Thermistor 5 BU Cavity Thermistor Humidity Sensor 600 HMI-C User Interface J5 3 4 3456 7 8 34 WIFI CORE P P P P P3 J5 J OR YL 3 4 5 P6 Fuse 50mA Control Inverter Control Panel Assembly J7 YL OR Oven Temperature Sensor Grill Relay 4904 Conv. Relay 4905 HMI Right OR Meat Probe Sensor V V OR GN BU TN Motor Latch Switch BR Door Switch OR/ Broil 600W BR OR P 3 4 5 7 Conv. 00W 8 BU 44 BU P8 MW Relay CN70 3 4903 MW Inverter 9 BU PWM P355 63 CN703 E70 CN70 P354 90 9 Microwave Appliance 9 YL/ Manager Magnetron GN Secondary Interlock Switch 4 6 3 3 Antenna 3456 7 8 90 J8 P3 / Copernicus Appliance Manager K4 K5 K6 K7 K8 K K0 K K3 K9 K TR TR EOL Convection Thermostat Opens at 93 F (45 C) Closes at F (05 C) GN BU Broil - 4000W BU PX4 Bake - 800W 34 34 YL Up Convect - 3400W YL PX Temperature Limiter Open Temp 30 F (50 C) / YL HS Cooling Fan PX YL Low Convect - 3400W YL 34 34567 PX3 P7 P5 GY GY GY/ Oven Lights LS Cooling Fan YL Motor Door Latch OR/ LS Convect Fan - Upper HS Convect Fan - Upper LS Convect Fan - Lower HS Convect Fan - Lower N L L LEGEND Ground (Chassis) Plug With Female Connector Receptacle With Male Connector Light(s) AC Drive Motor Door Switch Relay Contact Heating Element Enclosed Thermistor Latch Switch Thermal Fuse (Non- Resettable) Temperature Limiter Thermoactuator Microwave Light Transformer Magnetron Fuse 3

W0767738B For patent information, please see Pat. www.patent-listing.com 05. All rights reserved. W0767738B NOTE: This sheet contains important Technical Service Data. FOR SERVICE TECHNICIAN ONLY DO NOT REMOVE OR DESTROY 6/5 FOR SERVICE TECHNICIAN S USE ONLY