ICPE 313 Splaiul Unirii, Bucharest, Romania Tel/Fax: +40 021 589 34 80 sicit@icpe.ro www.icpe.ro Alina Pǎun Marketing Assistant 0723046531 alina.paun@icpe.ro UNDERFLOOR ELECTRICAL HEATING Brief description Benefits Applications Design ICPE s solution Brief description The electrical underfloor heating is a modern, simple to install and efficient solution for heating any type of buildings, even for temperature sensitive floors, ensuring maximum of comfort, as the warm air is distributed efficiently across the floor, and a precise adjustment of temperature with low running costs. These systems allow the substitution of the old techniques for removal of ice and snow, that were mainly based on treating the desired surfaces with salt and sand or applying mechanical methods for clearing, thus increasing the time life of the construction materials. Benefits This type of system can be installed for any type of finite floor: marble, sand stones, mosaic, linoleum, parquet, wood floor, land, rooms for animal growth. The design of the electrical heating systems depends on the room size, floor material, climate, etc. This system is practically invisible, silent and ensures an uniform temperature distribution on the entire heated surface, thus obtaining a superior degree of comfort with respect to the classical radiators heating methods. An additional benefit is the increasing of space, aspect essential for new buildings and projects. In the case of the later ones, the hot air case is lifted to the superior part of the room, while for the electrical underfloor heating systems it is kept on the floor vertical direction, being known the fact that temperature decreases with 2 Celsius degrees/meter on the vertical axis. This is one of the reasons for which this type of systems is also known as healthy heating systems. Another reason is the fact that the air dust is significantly reduced as the air is no longer circulated inside the heated space. Other advantages of the underfloor heating Low heating surface temperature Lack of the lateral air currents Non-polluting Highest yield No maintenance
Applications Direct-rapid heating Steam accumulation heating Supplementary heating Bathrooms, halls Temporary heating Heating of greenhouses Loading platforms, side-walks, roofs Conducts, transmissions antenna, raceways Design This type of heating system can be used for every finite floor type: marble, sand stones, mosaic, linoleum, parquet, wood floor, land, rooms for animal growth. The design of the electrical heating systems depends on the room size, floor material, climate, etc. The underfloor-heating system is generally suitable for direct heating. For underfloor-heating through concrete layer, cables of maximum power (18 W/m 2 ) are used. For medium size rooms, the cables are assembled so that the power installed should vary between 60-100 W/m 2 (direct heating). For bathrooms, it is recommended that the power installed should be less than 100 W/m 2 as, for such rooms, a warm floor is desired. For heating through accumulation (concrete, land), the heating cables are introduced in a bulk concrete layer (with a thickness of minimum 10 cm);the later accumulates the heat produced by the cables during the reduced consumption periods ( on the night times) and releases it during the day and in the evening, the maximum installed power being of 175 W/m 2. ICPE s solution ICPE Center of Electrotechnical Materials and Environmental Technologies is an important producer of electrical heating cables and is specialised in designing, manufacturing and installing a complete underfloor electrical heating system, suitable for various applications, like: industrial, commercial and domestic heating, external surface heating, removal of ice and snow and protection against and anti-freezing. Stranded resistant conductor Fluorocarbon resin insulation (200 o C) Tinned copper screen for electrical protection Protection sheath Manufactured according to directives of the International Electrotechnical Commission: IEC STANDARD Publication 800 - heating cables for a nominal current of 300/500V used in the heating of rooms as well as freezing prevention. Manufactured according to the ISO 9001 Quality Assurance System.
Types C6YEY 640 W 21 W/m 230V C6YEY - 483 W 23 W/m 230 V C6YEY 560 W 10 W/m 230V C6YEY 453 W - 18 W/m 230V C6YEY 1050 W 15 W/m 230V C6YEY 1200 W 12 W/m 230V C6YEY 1550 W 15 W/m 230 V Stages Cable assembly Net assembly FLIR Systems Li1 Ar1 Sp1 22.2 C 22 20 18 16.2 IR Analysis of the heated surface