In-Wall Subwoofer Series Owners Manual IWS-10 IWS-8

In-Wall Subwoofer Series Owners Manual IWS-10 IWS-8

Installation Tools needed for installation - Pencil - Drill - Tape Measure - Wire cutter - Philips-head screwdriver - Sandpaper Quick installation guide - Where is the best place to install the speakers - Where do the speakers sound the best - Try to separate the speakers 6-10 feet apart. - When placing the speakers in the wall, try to locate them so that the sound is projected towards the general listening area. - If you intend to paint the grilles, try to do so before installation. STEP 1 Trace along the inclusive template. Cut along the traced line using a drywall saw or rotary drill. A simple, inexpensive drywall saw (about $10 at your local hardware store) is the best choice for beginners. Caution: This is the most important part of the entire installation. If you are not certain whether any obstructions exist behind the desired mounting area, you should start by cutting a small hole in the center of your penciled mounting hole with a drywall saw. Use a piece of sandpaper to sand down the cut out edge for a smoother contour. (See Diagram 1 and Diagram 2) STEP 2 ---------------- -------------- - - Utility knife - Safety eyewear - Gloves Diagram 1: Cutout tracing Run the cable into the cut out location while leaving an extra two feet to make the connection to the speaker easier. Strip back approximately ½ of the speaker cable insulation and twist the copper wires tightly for easy insertion. Speaker wire To determine the length and the gauge of speaker wire, you will need to measure the distance between your receiver/amplifier and the speakers. - Measure the distance from the receiver/amplifier to the speakers. - Always buy more than you think you would need. - Equal wire lengths should always be used to maintain an equal balance in sound volume. - Sound quality is lost when using thin wire gauge over a long distance. 18AWG minimum - for distances up to.. 10 ft 16AWG - from. 10 to 50 ft 14AWG - from 50 to 100ft STEP 3 Tighten the dog-ear brackets by simply turning the screws on the slowly clockwise. The quick-turn mounting system and frame will "sandwich" or clamp around the wall to hold the speaker securely in place. (See Diagram 3) Diagram 3: Mounting Dog Ear Loose Closed STEP 4........ dog ear Loose...... Closed Tighten the four mounting screws with the same amount of force until the speaker is aligned and held securely to the wall surface. Caution: do not over tighten! (See Diagram 4) On the back of the speaker, press down on the gold-plated compression terminal to reveal the "eye" and insert the speaker cable through the eye for secure connection. Release the compression terminal to lock each cable securely. ---------------- Diagram 2: Cut Out Diagram 4:

- - Next, individually turn each of the screws (Diagram 5) that operate the dogears counter clockwise a few turns until you feel the dogear is loose from the resting position. Then turn the scew clockwise until you feel the dogear makes contact with the wall surface. Diagram 5: comparable to the speaker s power handling. Please refer to your owner s manual for reference. TIP: Blown-in insulation can sometimes work its way into the moving components of the speaker and negatively impacting performance. It is best to replace about a one square foot section directly behind the speaker with rolled-in (bat) insulation. (See Diagram 5) (See Diagram 7) Diagram 7: Subwoofer Amplifier Diagram 6: Terminal identification Note: The speakers wire should be about the same lenght. if excess wire behind the wall Note: Speaker terminals have corresponding () and (-) terminals. It is important to connect both speakers in phase. Out of phase will result in thin sound and weak bass. (See Diagram 6) Power Handling (25 Watts) Minimum - Warranty & Repair All OSD AUDIO speaker products have (10) year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all claims. During the warranty period OSD AUDIO will replace any defective part and correct any defect in workmanship without charge for either parts or labor are not OSD AUDIO s responsibility. For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by OSD AUDIO. The unit must be returned to OSD AUDIO at the owner's expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor is damaged resulting from abuse or from servicing performed by an agency or person OSD AUDIO sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any OSD AUDIO product purchased from an unauthorized dealer or other source, including retailers, mail over dealers and online sellers will not be honored or serviced under existing OSD AUDIO warranty policy. Any sale of product by an unauthorized source or other manner not authorized by OSD AUDIO shall void the warranty on the applicable product. Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail value of the parts and labor. To return for repairs, you must email customer service at RMA@OSDAUDIO.com for a Returned Merchandise Authorization (RMA) number# then the unit must be shipped to OSD AUDIO at the owner's expense, along with a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit. This Warranty Does Not Cover: Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) Any product whose identifying number of decal, serial #, etc. has been altered, defaced or removed Normal wear and maintenance.

In Ceiling Model ICE-850 ICE-840 ICE-810 Tweete: 8 Kevlar Ceiling Home Theater Speakers 8 Kevlar Cones 92dB 8 High Definition Pro Series 91dB 8 Custom Series 89dB 26Hz - 22kHz 36Hz - 22kHz 140 Watts Dimensions: (D x H) 11 x 4 ¼ 10 ¾ x 3 10 ¾ x 3 Ceiling Cut Out: 9 9 9 Unit of Measure: Pair Pair Pair In Ceiling Model ICE-650 ICE-640 ICE-620 6 ½ Kevlar Ceiling 6 ½ Kevlar Cones Pro Series 91dB 6 ½ Custom Series 89dB 58Hz - 22kHz Dimensions: (D x H) 9 ¼ x 3 9 ½ x 3 3 8 9 ½ x 2 Ceiling Cut Out: 8 7 7 ¾ Unit of Measure: Pair Pair Pair LCR Ceiling Model ICE-870 ICE-670 ICE-660 ICE-630 Dimensions: (D x H) Ceiling Cut Out: 8 Kevlar LCR Ceiling 8 Kevlar Cones 26Hz - 22kHz 11 x 5 7 8 9 6 ½ Kevlar LCR Ceiling 6 ½ Kevlar Cone 9 ¼ x 4 8 ¼ Pro LCR 50Hz - 22kHz 10 ½ x 5 8 Unit of Measure: Each Each Each Each 6 ½ Custom LCR Series 91dB 52Hz - 22kHz 10 ½ x 5 8 OSD Audio 775 Columbia Street Brea, CA 92821 Ph: 888.779.4968 osdaudio.com

In Wall Model IW-850 IW-840 IW-810 IW-690 8 Kevlar Inwall 8 Kevlar Cones 8 High Definition Pro Series 8 Custom Series 6 ½ Kevlar Inwall 6 ½ Kevlar Cones 26Hz - 22kHz 36Hz - 22kHz 150 Watts Dimensions: (H x W x D) 14 x 10 x 3 ¾ 13 ¾ x 10 x 3 ¾ 13 ¾ x 10 x 3 5 8 12 ¼ x 8 x 3 13 x 8 ¾ 8 ¾ x 12 ¾ 12 ¾ x 8 ¾ 10 x 6 ¾ Unit of Measure: Pair Pair Pair Pair In Wall Model IW-680 IW-670 IW-540 IW-530 Pro Series 6 ½ Custom Series el 5 ¼ High Definition Pro Series In Wall Speaker 5 ¼ Custom Series 87dB 87dB 48Hz - 22kHz 58Hz - 22kHz 68Hz - 22kHz Dimensions: (H x W x D) 12 x 8 x 3 3 8 12 x 8 ½ x 3 10 x 7 x 2 ¾ 10 x 7 x 2 ½ 7 x 10 13 16 10 x 7 5 6 6 x 9 5 8 9 x 6 1 8 Unit of Measure: Pair Pair Pair Pair In Wall Center LCR IW-550 IW-545 IW-525 Dimensions: (H x W x D) 5 ¼ Kevlar Center Channel LCR In wall Home Theater Speakers Dual 5 ¼ Kevlar Cones 91dB 1w/1m 8 x 15 x 3 5 ¼ High Definition Pro Series Center In Wall LCR Speakers Dual 50Hz - 22kHz 15 x 8 3 ½ 6 x 14 ½ 13 x 6 7 8 Unit of Measure: Each Each 5 ¼ Custom Series Center Channel LCR Dual 55Hz - 22kHz 15 x 8 3 ½ 13 x 6 7 8 Each OSD Audio 775 Columbia Street Brea, CA 92821 Ph: 888.779.4968 osdaudio.com

In Ceiling Model ICE-540 5 ¼ High Definition Pro Series ¾ Silk Dome ICE-530 5 ¼ Custom Series ¾ Silk Dome Swivel 88dB Dimensions: (D x H) 58Hz - 22kHz 7 ¾ x 2 ¾ 65Hz - 22kHz 8 x 2 ¾ Ceiling Cut Out: 6 6 Unit of Measure: Pair Pair Dual Tweeter ICE-840TT ICE-640TT ICE-620TT 8 High Definition Pro Series Dual ¾ Silk Dome Pro Series Dual ¾ Silk Dome 6 ½ Custom Series Stereo Speakers Dual ¾ Silk Dome 86/89dB 86/89dB 86/89dB 36Hz - 22kHz 40Hz - 22kHz 150 Watts 40Hz - 22kHz Dimensions:(D x H) 11 ¾ x 3 9 ½ x 3 9 ½ x 3 Ceiling Cut Out: 9 7 7 ¾ Unit of Measure: Each Each Each In Wall Subwoofer IW-S10 10 In Wall Subwoofer IW-S8 8 In Wall Subwoofer 10 Polyproplene Subwoofer 86dB 87dB Mounting Depth: 38Hz - 200Hz /- 3dB 25-200 watts 40Hz - 200Hz /- 3dB 25-150 Watts 3 3 ¾ 10 x 10 8 ¾ x 8 ¾ Unit of Measure: Each Each OSD Audio 775 Columbia Street Brea, CA 92821 Ph: 888.779.4968 osdaudio.com