Streamline ontrol Panel 4804-RQ
OFF ED... 4. 5. 6. 7. 8. 9. 0.... 4. 5. 6. 7. 8. 9. Packing ist Streamline ontrol Panel (4804-RQ) No. Qty. Part No. Description 6 09-VUT -SUA 458-VUS 845-VU 857-VU 899-VU 860-VU 86-VU 844-VU 0557-VUP 0-VUW -VUW 8-VUI 49075-VUI 4904 49007 64-VU -VUW 9-VUW 48 Adjustable Rotary Slide POT w/ Pigtail -Spd Rotary 0-4 Nyloc Nut 7/6 Shaft Nut 8- X /8 ex Screw 0-4 Nut w/ Star Washer #8 Star Washer 0-4 X.75 Skr Set Screw ight ulb #0 Ring Terminal (/8) /4 Spade Terminal (/8) /4 Rubber Grommet Streamline Panel AS Knob AS, Strmln 50 X 56 Pol Streamline Slide POT Knob polish Streamline ontrol Panel rkt uddy lip 6 Jumper Wire ** efore beginning installation, open all packages and check contents of shipment. Please report any shortages directly to Vintage Air within 5 days. After 5 days, Vintage Air will not be responsible for missing or damaged items. 9 8 8 6 5 7 7 4 0 NOTE: Images may not depict actual parts and quantities. Refer to packing list for actual parts and quantities. 5 A 9 4 6
Streamline ontrol Panel Template 5.0 Template For 4804-RQ evel This ine.0 NOTE: Ensure that template measures to dimensions noted above prior to cutting dash. ontrol Panel Installation. Select a suitable location for the control panel. onsider heater control valve location, wiring harness length and capillary tube to evaporator distance.. After selecting a location for the panel, mask the area ½ (tall) x 5 ½ (wide).. ut out grey section of template on dotted line. 4. ark dash with marker or scribe. NOTE: e sure to level template on dash. 5. ut out opening for panel. 6. Remove backing plate from face. 7. Install face in dash and reinstall backing plate, making sure the wires for the lights exit the holes in the backing plate. 8. Install the nuts with star washers, and then the bracket and nyloc nut. Do not overtighten the nyloc nut. 9. Tie one wire from each light bulb together and run them to a ground. 0. Tie the other wires together and connect to the wire in your vehicles harness that powers your instrument panel lights (+ volts).. Wire according to the wiring diagram on Page 7 for Gen II ompac & Gen II Super Units, or see Page 8 for the Gen II ini.. Insert capillary tube through the sticker on top of the evaporator, the entire thickness of the coil.
OFF ED ode Slide Potentiometer Nut ex Screw Star Washer Knob AS Top View Nut Nyloc Nut Top racket Nut W/ Star Washer acking Plate Streamline Polished Knob AS Panel Face OFF ottom racket ED Knob A Knob Retained y Allen Set Screw Set Screw Knob Assy Insert apillary Tube Through This ole the Entire Thickness of Evaporator oil. Dash racket acking Plate Side View 0-4 Nyloc Nut 0-4 Nut w/ Star Washer Streamline ontrol Panel Wiring Diagram Rotary ontrol Panel (Rear View) onnect to Existing Instrument Panel ight Wiring (+) ode onnect to hassis Speed apillary Tube Plug From Potentiometer ust be onnected to Electronic odule arness.
Streamline Operation of ontrols OT OT System Off Turning the speed Knob to OFF will shut down the system in any mode. OT Vent eat ode Select fan speed. Rotate mode knob to and slide the heater control lever to the right for mode. ot air will exit the dash vents. Defrost ode (Optional, for Defrost Only!) Select fan speed. Rotate mode Knob to. Turn the knob slightly clockwise to engage the compressor. Slide heater control lever to the right to open hot water valve to provide heated defrost air. Dehumidified defrost air will be directed to windshield. OT ode Turn thermostat knob clockwise for cold air, and adjust mode knob to or. old air will flow from vents. NOTE: Duct temperature can be raised by slightly sliding hot air lever to the right to open hot water OT valve. ot water valve must be closed (full left) for coldest setting. Floor eat ode Select fan speed. Rotate mode knob to, and slide the heater control lever to the right for mode. ot air will exit the floor vents. -evel eat ode Select fan speed. Rotate mode knob to. For level, slide the heater control lever to the right for. ot air will exit the dash floor & vents. OT
Wiring Diagram Gen II ompac/super Units eat/ool/defrost (Optional) ompressor Safety (inary Type) lutch lack ode Fan Speed Pink Green Power Relay 87 87a 86 85 0 (Optional) For Defrost Only! / / Grey/lack / / Grey/lack 87 87a 86 85 0 igh Relay eater ontrol Valve Potentiometer Aux. otor onnect to Key on Ignition Source (5 Amp Fuse) 0 Amp circuit breaker at. ontrol odule To attery or attery Terminal on Starter Solenoid. lack rown t. Floor/Vent Servo GREY PURPE (Optional) For Defrost Defrost Only! Servo Note Orientation of Plugs lack/ / / /rown / eater ontol Valve Servo
Wiring Diagram Gen II ini Units eat/ool/defrost (Optional) ompressor Safety (inary Type) lutch lack ode Fan Speed Pink Green Power Relay 87 87a 86 85 0 (optional) For Defrost Only! / / Grey/lack / / Grey/lack 87 87a 86 85 0 igh Relay eater ontrol Valve Potentiometer lack Spal Type otor Aux. Resister On onnect to Key on Ignition Source (5 Amp Fuse) 0 Amp circuit breaker at. To attery or attery Terminal on Starter Solenoid. ontrol odule rown lack t. Floor/Vent Servo Grey (optional) For Defrost Defrost Only! Servo (Rear View of Plug) Note Orientation of Plugs lack/ / / /rown / eater ontol Valve Servo
Imporatant Notice Please Read! NOTE: Evaporator thermostat capillary tube must be inserted Through evaporator sub case coil. See illustrations below. Refer to seperate instructions included with your evaporator kit to insert the capillary tube. ompact Sub case Top View Shown INSERT TEROSTAT APIARY TUE TRU TS OE TE ENTIRE TKNESS OF EVAPORATOR OI. Insert thermostat capillary tube here into the coil the entire thickness. Then carefully bring it back out approx. one inch This sticker is located on the top side of the evaporator case. Insert apillary Tube Through This ole the Entire Thickness of Evaporator oil. older Warmer lockwise Adjustable Knob ounterclockwise OFF ED apillary Tube to Evaporator oil Air onditioning Adjustments. The air conditioner thermostat controls coil temperature. It is shipped adjusted fully cold (clockwise) and, in the majority of cases, the will operate correctly as shipped.. Turning the knob on the thermostat to the right (clockwise) makes the system operate colder. If the thermostat is set too cold, the evaporator will ice up. If this happens, the evaporator coil is restricted with ice and cold air flow will be reduced.. Turning the knob to the left (counterclockwise) makes the system operate warmer. The compressor clutch will cycle off frequently and the system will not get as cool as it could. Adjusting. Symptom: The works well at first, but then quits cooling. The air flow from the vents is low and the compressor cycles infrequently. Solution: The thermostat is set too cold and the evaporator is icing up and restricting air flow. Allow the ice to melt and set the thermostat warmer (counter clockwise) 0% of a turn each adjustment until the symptoms diminish.. Symptom: never gets cold and the compressor clutch cycles frequently. Solution: The thermostat is set too warm. Set the thermostat colder (clockwise) 0% of a turn each adjustment until the compressor clutch cycles infrequently. Avoid setting the thermostat too cold.. Symptom: The never gets cold, sometimes even blows hot, and the compressor clutch infrequently cycles off. Solution: The heater may be on at all times. arefully feel around the heater hoses at the firewall. They should be cold when the is on. If the hoses are hot: A) The heater control valve may be installed backwards. heck the flow direction arrow on the valve against the illustration in your installation instructions. ) The heater control valve is installed in wrong heater hose.
OFF ED Packing ist Streamline ontrol Panel (4804-RQ) No. Qty. Part No. Description... 4. 5. 6. 7. 8. 9. 0.... 4. 5. 6. 7. 8. 9. 6 09-VUT -SUA 458-VUS 845-VU 857-VU 899-VU 860-VU 86-VU 844-VU 0557-VUP 0-VUW -VUW 8-VUI 49075-VUI 4904 49007 64-VU -VUW 9-VUW 48 Adjustable Rotary Slide POT w/ Pigtail -Spd Rotary 0-4 Nyloc Nut 7/6 Shaft Nut 8- X /8 ex Screw 0-4 Nut w/ Star Washer #8 Star Washer 0-4 X.75 Skr Set Screw ight ulb #0 Ring Terminal (/8) /4 Spade Terminal (/8) /4 Rubber Grommet Streamline Panel AS Knob AS, Strmln 50 X 56 Pol Streamline Slide POT Knob polish Streamline ontrol Panel rkt uddy lip 6 Jumper Wire EKED Y: PAKED Y: DATE: 9 8 8 6 5 7 7 4 0 5 9 4 NOTE: Images may not depict actual parts and quantities. Refer to packing list for actual parts and quantities. A 6